Sensys Networks FLEXRAD FLEXRADIO CABINET User Manual Quick Start Guide

Download:
Mirror Download [FCC.gov]
Document ID	3455200
Application ID	sO6VdCG5CyXMqNCPXXDCBA==
Document Description	Quick Start Guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	61.9kB (773762 bits)
Date Submitted	2017-07-07 00:00:00
Date Available	2017-07-07 00:00:00
Creation Date	2017-07-05 13:15:13
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2017-07-06 12:31:57
Document Title	Quick Start Guide
Document Creator	Adobe InDesign CS6 (Windows)

Quick Start Guide: FlexRadio Cabinet
Assemble
Tools Required
FlexRadio Cabinet requires the following tools for installation:
• #2 Phillips bit screwdriver
• 0.75” ( 1.9 cm) hole saw or step drill bit with power drill
FT
• Hand wrench
M3x4 mm screw x 4
Rail x 2
DR
FlexRadio Cabinet Installation Parts
A FlexRadio Cabinet assembly requires a single FlexRadio Cabinet module, omni
directional antenna, 6 foot coaxial cable, and the bracket/DIN mount kit.
Install FlexRadio Cabinet
M3x4 mm screw x 4
Rail x 2
Install FlexRadio Cabinet
Use the Sensys Networks provided DIN or bracket mounts to install the FlexRadio Cabinet inside the traffic cabinet.
Refer to Assembly Instructions Bracket and DIN Mounts for more information.
1608 4th Street Suite 200 Berkeley CA 94710 | info@sensysnetworks.com | P 510.548.4620 F 510.548.8264
Quick Start Guide: FlexRadio Cabinet
Install Omni Directional Antenna
Omni Directional Antenna Installation
FT
Please refer to Bolt-On Antenna Installation Guide Slotted Washer & Nut that is provided in the antenna
packaging for more details.
Drill a Hole in Traffic Cabinet
Drill a hole ¾ inches ( 1.9 cm) diameter for aluminum ferrule antenna on top of the flat
surface of the traffic cabinet with a hole saw or a step drill bit where the omni directional
antenna will be installed.
Note: Ensure the antenna hole location will not interfere with the traffic cabinet inside.
DR
Thread Connectors into Cabinet
Pass the connectors through the hole. Pull the cable
until the threaded end of the antenna ferrule appears
in the hole. DO NOT pull on connectors. Pulling on
the connectors may cause them to detach or may cause
internal damage to the cable connection.
Add Washer
Install the plastic washer (a) onto
the threaded ferrule. Ensure the
flange on the washer is seated on
the ¾ inch hole. The flat side of
the washer contacts the nut.
1608 4th Street Suite 200 Berkeley CA 94710 | info@sensysnetworks.com | P 510.548.4620 F 510.548.8264
Quick Start Guide: FlexRadio Cabinet
Install Omni Directional Antenna (cont.)
Connect Cables to the FlexRadio Cabinet
DR
FT
Secure Nut
Install nut on threaded ferrule. Hand tighten the nut until it contacts
the plastic washer. Use a wrench to tighten the nut two more turns to
secure the antenna and to seat the antenna’s gasket.
Connect the Antenna to FlexRadio Cabinet
Connect the RP TNC male end to the
FlexRadio cabinet.
WARNING: DO NOT OVER BEND
CABLE. Do not bundle excess cable; only
loop with bend radius no smaller than 6
inches (15.2 cm).
Power FlexRadio Cabinet
Connect FlexRadio Cabinet module to FlexControl Module
using CAT5 (or better) straight-through cables via TO: SPP
PORT on the FlexRadio Cabinet module and the SPP-0 (or
SPP-1) port on the FlexControl Module.
Notice: Any changes or modifications not expressly approved by
Sensys Networks could void the user’s authority to operate the
equipment. The external antenna must have gain less than +6dBi to
meet regulatory requirements.
Local Distributor
Sensys Networks and the Sensys Networks logo are trademarks of Sensys Networks, Inc. All other trademarks are the property of their respective owners.
Information contained herein is believed to be reliable, but Sensys Networks makes no warranties as to its accuracy or completeness.
Copyright © 2017 Sensys Networks, Inc. • ALL RIGHTS RESERVED • P/N 152-240-XXX-XXX Rev A

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2017:07:05 13:15:13-07:00
Creator                         : Adobe InDesign CS6 (Windows)
Modify Date                     : 2017:07:06 12:31:57-07:00
Has XFA                         : No
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2017:07:06 12:31:57-07:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:09d945fc-af93-4984-b6e2-62d660419436
Original Document ID            : xmp.did:F77F1174072068118083FBAF5E674C88
Document ID                     : xmp.id:62892B7BBE61E711BB12E1DAC7B850D8
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:60892B7BBE61E711BB12E1DAC7B850D8
Derived From Document ID        : xmp.did:A5C428BC56CFE511926CE633F6FEF101
Derived From Original Document ID: xmp.did:F77F1174072068118083FBAF5E674C88
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2017:07:05 13:15:13-07:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 3

EXIF Metadata provided by EXIF.tools