Sercomm SWPIR03N Z-Wave Motion Sensor User Manual

Sercomm Corporation Z-Wave Motion Sensor Wireless 802 11g Network Camera

a href="https://usermanual.wiki/Sercomm" itemprop="url"> Sercomm >

Users Manual

1 SW-PIR03N Z-Wave Motion Sensor Installation Guide SW-PIR03N is a PIR (Passive Infrared) sensor, which can detect levels of infrared radiation from objects in its range of view. This Motion Detector is fully compatible with any Z-Wave controller and can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network." It is also a pet immune motion sensor, which is used to ignore the motion caused by animals and thus reduce the likelihood of false alarms. The sensitivity of the sensor will disregard the motion caused by animals under 85 pounds, like a full-grown dog or small cats. In addition, the SW-PIR03N has walk test mode and white light immunity, which can be used to reduce false alarms caused by lights, flashlights or other reflective objects. These outstanding features of the sensor provides the professional security for protecting any home or business to save time, money and deliver a great surveillance experience as well. Specification Frequency 908.4~916 MHz Battery Type GP CR123A * 1 RF Transmission Range Outdoor: 60 Meters Temperature Sensor ±1 C Accuracy Rearm Timer 3 Minutes Operating Temperature 0 C to 50 C (32° - 122°F) Storage Temperature -20 C to 65 C (-4° - 149°F) Battery Life 2 Years (Assume 30 trigger events per day @25°C) Dimensions (H xW x D) 93.4mm x 50mm x 31.8mm Detect Range Distance: Max. 15M (±1M) w/mounting height 1.8M @25°C Angle: Max. 90 (±10) Degree @25°C Package Contents Installation 1. Detach the mount bracket from the device. 2. Install the provided battery correctly. 3. Attach the mount bracket back to the device.
2 Operation 1. PIR LED (Red) 5. Pairing LED (Green) 2. Tamper Switch 6. Battery Cover (Wall Mount Bracket) 3. Jumper (Walk Test) 4. Battery  Remove the protection film on front panel before installation.  When the battery is installed, the PIR LED will be blinking for 30 seconds and then turn off when the Motion Sensor is ready to be used.  After the tamper switch is pressed, the Motion Detector will be in normal mode. The PIR LED on the device will illuminate when the Motion Detector is triggered.  When the Motion Detector is triggered, it will send Basic Set ON (0xFF).  If no movement detected in three minutes, it will send Basic Set OFF (0x00). CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECTED TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Add (Inclusion) Sensor For adding in (Inclusion) a network: Put the Z-Wave controller into "Add (Inclusion)" mode, and follow its instruction to add SW-PIR03N to your controller. This sensor needs to be included before installation. 1. Install the battery and the Pairing LED indicator will be lit for one second to indicate a successful booting. 2. It will blink one time every second while scanning the network. 3. If the network is not found after 30 seconds, the sensor will go into sleep mode. To wake the sensor again, you need to use the tamper switch to trigger the adding (Inclusion) process, and then the sensor will repeat steps from 2 to 3. Remove (Exclusion) Sensor 1. Set the Z-Wave controller to "Exclusion" mode. 2. Press the tamper button 3 times within 2 seconds. 3. The PIR LED will light up for 1 second if success. 4. The device will begin to search for a new network. Association Associations (Association Command Class Version 2) This Sensor supports 2 association groups. This has the effect that when the sensor is triggered, all devices associated with the sensor will receive the relevant reports. Through an association the sensor may control another Z-Wave network device, e.g. a alarm device, wall plug, lamp etc.
Download:
Mirror Download [FCC.gov]
Document ID3257350
Application IDgLdk0/CL6wT4YfJx5s1W0Q==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize56.05kB (700586 bits)
Date Submitted2017-01-13 00:00:00
Date Available2017-01-17 00:00:00
Creation Date2016-12-21 18:43:23
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2016-12-21 18:43:23
Document TitleWireless (802.11g) Network Camera
Document CreatorMicrosoft® Office Word 2007
Document Author: KAREN CHOU
FCC ID Filing: P27SWPIR03N

Navigation menu