Seura BTM1 Bluetooth Receiver Module Board User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3894323
Application ID	gTf78sqSwBZ7U6Xy8G6WFg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	32.27kB (403334 bits)
Date Submitted	2018-06-20 00:00:00
Date Available	2018-06-21 00:00:00
Creation Date	2018-06-20 15:11:36
Producing Software	Foxit PhantomPDF Printer Version 6.1.0.0923
Document Lastmod	2018-06-20 15:11:36
Document Title	User Manual

User Manual For Bluetooth Board
1. Function
Be used for communicating with other Bluetooth device (by Bluetooth mode) or other
sound source device (by AUX Mode), transmitting audio signal to amplify borad
2. Operation
Track playback controller connects to the external keypad through an I2C interface,
enabling play/pause, last song, next song, volume +, volume -, Bluetooth /AUX to be
switched.
Through a 3-pin serial port, you can set the Bluetooth board broadcast name, password,
address, etc.
LINE
OUT
I2C port
AUX in
RS323port
DC-out
24V port
DC-in 24V
Reset
Control command, refer to“RS232 Commands and Responses for BlueTooth
Receiver(20180428).xlsx”. and “CMD(20180503).TXT”.
3. Statement
Federal Communications Commission (FCC) Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generate, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
RF exposure warning
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
This equipment must not be collocated or operating in conjunction with any other antenna
or transmitter.
OEM Integration Instructions：
This device is intended only for OEM integrators under the following conditions：
The module can be used to installation in specific host (Host information as follows). The
module shall be only used with the integral antenna(s) that has been originally tested and
certified with this module. As long as 2 conditions above are met, further transmitter test
will not be required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirement with this module installed.
Host
Product Name: Lighted Bluetooth Mirror
Manufacturer: SEURA
Model Name: S-S-2424-SA-VE.6-BLED-BT
IMPORTANT NOTE：
In the event that these conditions cannot be met (for example certain laptop configuration
or co-location with another transmitter), then the FCC authorization for this module in
combination with the host equipment is no longer considered valid and the FCC ID of the
module cannot be used on the final product. In these and circumstance, the OEM
integrator will be responsible for re-evaluating. The end product (including the transmitter)
and obtaining a separate FCC authorization. The final end product must be labeled in a
visible area with the following: “Contains Transmitter Module FCC ID: 2APLNBTM1 or
Contains FCC ID: 2APLNBTM1”.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Page Count                      : 4
Author                          : 
Create Date                     : 2018:06:20 15:11:36+08:00
Creator                         : 
Modify Date                     : 2018:06:20 15:11:36+08:00
Producer                        : Foxit PhantomPDF Printer Version 6.1.0.0923
Subject                         : 
Title                           : 

EXIF Metadata provided by EXIF.tools