Sharp BSC0001 Wireless Module User Manual

Sharp Corporation Wireless Module

User manual

26-Aug.-2016 Ver.0.3 SHARP CORPORATION 1/7 RUITZ0004MPZZ Bluetooth ® low energy Module Bluetooth® 4.2 low energy RUITZ0004MPZZ Data Report Please note that this manual should not be provided to end-users.
26-Aug.-2016 Ver.0.3 SHARP CORPORATION 2/7 RUITZ0004MPZZ Control No. HD-AG-A150049 (1/5) Control name General Items Scope This specification (“Specification”) applies to the hybrid IC “RUITZ0004MPZZ”, a Bluetooth® 4.2 low energy module (“Product”). 1. Type: RUITZ0004MPZZ 2. Function: Radio frequency module. Bluetooth® standard Ver 4.2 low energy conformity 3. Application: Health & Fitness Equipment, Sensor, Toys 4. Note: a. Regulatory information: Compliance with each radio law and/or regulation in below listed countries has been confirmed under the conditions follows: - Company name of Manufacturer: SHARP CORPORATION - Equipment name/ Model name: Wireless Module / RUITZ0004MPZZ - Manufacturing date: traceable from “lot number” shown on device - Country of origin: JAPAN - Countries: Canada, Japan, U.S.A. To maintain the compliance, please install RUITZ0004MPZZ into your final product within the scope of the specification and regulation of each country. Japan Regulatory Information This module is approved with the specific antenna on this module. a) Please ensure that your product can bear a label with the following information. If the product is so small that it is not practicable to place the label, please place it in the instruction manual and package. The mark diameter shall be equal or greater than 3mm. This product installs a radio system which has been approved as a radio station in a low power data communication system based on the Radio Law. RUITZ0004MPZZ : 001-A05676
26-Aug.-2016 Ver.0.3 SHARP CORPORATION 3/7 RUITZ0004MPZZ Control No. HD-AG-A150049 (2/5) Control name General Items Canada Regulatory Information a) This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. L'utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l'utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. b) This product is certified as type of the portable device with Industry Canada Rules. To maintain compliance with RF Exposure requirement,please use within specification of this product. - IC: 548B-RUITZ0004MP Ce produit est certifié comme type de l'appareil portable avec Industrie Règles de Canada. Pour maintenir l'acquiescement avec exigence Exposition de RF, veuillez utiliser dans spécification de ce produit. - IC: 548B-RUITZ0004MP c) Please notify certified ID by either one of the following method on your product. Specifiez ID certifiée dans votre produit par une de méthode suivante. -Contains Transmitter module IC : 548B-RUITZ0004MP -Contains IC : 548B-RUITZ0004MP Pecifiez ID certifiée dans votre produit par une de méthode suivante. -Contains Transmitter module IC : 548B-RUITZ0004MP -Contains IC : 548B-RUITZ0004MP FCC Regulatory Information a) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. b) Please notify certified ID by either one of the following method on your product. -Contains Transmitter Module FCC ID: APYBSC0001 -Contains FCC ID: APYBSC0001 c) CAUTION: changes or modifications not expressly approved by the party responsible for compliance could void the use’s authority to operate the equipment. d) This product is certified as type of the portable device with FCC Rules. To maintain compliance with RF Exposure requirement, please use within specification of this product. - FCC ID: APYBSC0001 e) The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
26-Aug.-2016 Ver.0.3 SHARP CORPORATION 4/7 RUITZ0004MPZZ Control No. HD-AM-A150049 (1/1) Control name Absolute maximum ratings Absolute maximum ratings Symbol Parameter Min. Max. Units VCC_NRF -0.3 +3.6 V GND 0 V VIO -0.3 VCC_NRF+ 0.3 V Storage temperature -40 +85 Deg-C MSL Moisture Sensitivity Level 3 ESD HBM Human Body Model 1 kV ESD MM Machine Model 100 V Endurance Flash Memory Endurance 20000 write/erase cycles Retention Flash Memory Retention 10 years At 40 deg-C Number of times an address can be written between erase cycles 2 times
26-Aug.-2016 Ver.0.3 SHARP CORPORATION 5/7 RUITZ0004MPZZ Control No. HD-AE-A150049 (1/7) Control name Electrical characteristics Electrical characteristics Recommendation operating range Symbol Parameter Min. Typ. Max. Units VCC_NRF Supply voltage, normal mode 1.8 3.0 3.6 V VCC_NRF Supply voltage, normal mode, DC/DC converter output voltage 1.9 V 2.1 3.0 3.6 V tR_VCC_NRF Supply rise time (0V to 1.8V)*1 100 ms TA Operation temperature -25 25 75 Deg-C *1 The on-chip power-on reset circuitry may not function properly for rise times outside the specified interval. Also after power off, please start up from below 0.3V. RF Specifications Symbol Description Min. Typ. Max. Units Fop Operating frequencies 2402 2480 MHz PLLres PLL programming resolution 1 MHz Df Frequency deviation +/-225 +/-250 +/-275 kHz PRF Maximum output power 4 dBm PRFC RF power control range 20 24 dB PRFCR RF power accuracy +/-4 dB PWHISP RF power whisper mode -30 dBm PBW 20 dB bandwidth for modulated carrier 950 1100 kHz PRF1 1st Adjacent Channel Transmit Power 1 MHz -20 dBc PRF2 2nd Adjacent Channel Transmit Power 2 MHz -45 dBc PRXMAX Maximum received signal strength at < 0.1% PER 0 dBm PSENS IT Receiver sensitivity (0.1% BER) Ideal transmitter -93 dBm PSENS DT Receiver sensitivity (0.1% BER) dirty transmitter -91 dBm
26-Aug.-2016 Ver.0.3 SHARP CORPORATION 6/7 RUITZ0004MPZZ Control No. HD-BA-A150049 (1/2) Control name Pin Layout Pin Descriptions Pin Pin name Pin function Description 1 GND Ground Ground (0 V) 2 P0.27 AIN1 XL1 Digital I/O Analog input Analog input General purpose I/O pin ADC input 1 Crystal connection for 32.768kHz crystal oscillator or external 32.768kHz crystal reference 3 P0.26 AIN0 XL2 Digital I/O Analog input Analog output General purpose I/O pin ADC input 0 Crystal connection for 32.768kHz crystal oscillator 4 P0.21 Digital I/O General purpose I/O pin 5 VCC_NRF Power Power supply 6 AVDD Power Analog Power supply 7 P0.23 Digital I/O General purpose I/O pin 8 P0.17 Digital I/O General purpose I/O pin 9 GND Ground Ground (0 V) 10 DEC2 Power Power supply for low voltage mode 11 P0.19 Digital I/O General purpose I/O pin 12 GND Ground Ground (0 V) 13 OUT_ANT Antenna In/Out Internal antenna. It should be connected to Pin 14 OUT_MOD for normal operation. 14 OUT_MOD RF In/Out RF I/O pin. It should be connected to Pin 13 OUT_ANT for normal operation. 15 GND Ground Ground (0 V) 16 SWDIO Digital I/O System reset (active low). Also HW debug and flash programming I/O 17 SWDCLK Digital input HW debug and flash programming I/O 18 P0.25 Digital I/O General purpose I/O pin 19 P0.03 AIN4 Digital I/O Analog input General purpose I/O pin ADC input 4 20 GND Ground Ground (0 V) 21 P0.01 AIN2 Digital I/O Analog input General purpose I/O pin ADC input 2 22 P0.02 AIN3 Digital I/O Analog input General purpose I/O pin ADC input 3
26-Aug.-2016 Ver.0.3 SHARP CORPORATION 7/7 RUITZ0004MPZZ Control No. HD-BA-A150049 (2/2) Control name Pin Layout Pin Pin name Pin function Description 23 P0.00 AREF0 Digital I/O Analog input General purpose I/O pin ADC Reference voltage 24 DCC Power DC/DC output 25 P0.05 AIN6 Digital I/O Analog input General purpose I/O pin ADC input 6 26 P0.06 AIN7 AREF1 Digital I/O Analog input Analog input General purpose I/O pin ADC input 7 ADC Reference voltage 27 P0.04 AIN5 Digital I/O Analog input General purpose I/O pin ADC input 5 28 GND Ground Ground (0 V)

Navigation menu