Shinwa 8811X Car Kit Bluetooth Module User Manual

Shinwa Industries (China) Ltd. Car Kit Bluetooth Module

User manual

BT-MC88-1X 产品说明书 1. 介绍 Introduction 1.1 简要 Overview ★ BT-MC88-1X是 一 款 基 于 CSR8811芯 片 设 计 的 HCI模 组 . BT-MC88-1X is a H CI module bas ed on CSR8811 ch ip. ★ BT-MC88-1X是 由 一 单 射 频 和 基 带 IC组 成 并 应 用 于 蓝 牙 2.4GHz系 统 的 模 组 . The BT-MC88-1X i s a module that Integrate a single-chip r adio and baseband IC for Bluetooth 2.4G Hz systems. 1.2 特征 Features ★ 蓝牙双模/蓝牙低功耗 Dual-mode Bluetoo th/Bluetooth low energy ★ 高品质蓝牙4.0 High qualit y Bluetooth v4.0 ★ Class2蓝牙功率等级 Bluetooth powe r level：Class 2 ★ 高速串行通讯接口（最高到4Mbps） High-speed UAR T port (up to 4Mbp s) ★ PCM/I2S兼容数字音频接口 PCM/I2S digital audio inter faces. ★ 支持IEEE 802.11协议 Support for IEEE 802.11 ★ 模组尺寸23*16*3.2mm，邮票孔，24个脚位（带屏蔽罩） Module size 23 *16*3.2mm, Sta mp-24(with shi eld case) ★ 模组内置PCB天线 Built-in pat tern antenna o n the module ★ 标准的HCI通讯接口 Standard HC I support ★ 宽电源供电，电压范围：2.7-3.6V Flexible voltage supply, supp ly range: 2.7 -3.6V ★ 环保RoHS Environmental car e: RoHS 1.3 应用 Applications ★ 车载免提 Hands-Free Car Kits ★ 低端手机、功能手机、智能手机 Low-cost phones , Feature phone s, Smart-phone s ★ 便携式媒体播放器 Portable media players
BT-MC88-1X Specification 12.规格 参数 3 射频规格 RF Spe 规格 Specification 条件 Condition 最小 Min. 典型 Type 最大 Max. 单位 Unit 输出功率 Output transmit power Normal -6 0 4 dBm 调制特性 Modulation characteristics f1 avg 140 175 kHz f2 max 115 kHz f2avg/f1avg 80 % 初始载波频率容限 Initial carrier-frequency tolerance Normal -20 20 kHz 载波频率漂移 Carrier frequency drift DH1 -25 25 kHz DH3 -40 40 kHz DH5 -40 40 kHz Draft rate/50us -20 20 kHz 备注：常温下是25±5℃ Remark: Normal Test Condition is 25±5℃ 1 产品或项目名称 Product/ Project Name 车载蓝牙模组 Car kit Bluetooth Module 2 芯片类型 Chip set BlueCore CSR8811 A08 0.5mm WLCSP 3 产品射频功率等级 Power class level Class 2 (-6dBm < PAV < 4dBm) 4 波特率 Baud Rate 9600bps～4Mbps 5 额定电压 Rated Voltage 3.3V 6 工作电压范围 Operation Voltage range 2.7V～3.6V 7 工作范围 Operation Range 10 meters (33 feet) 8 尺寸 Dimension 23*16*3.2mm （L*W*H） 9 核心规格版本 Core Specification Version □1.2 □2.0 □2.0+EDR □2.1 □2.1+EDR ■3.0 □3.0+HS ■4.0 10 认证 Test of certification FCC\CE\IC\MIC\BQB 11 工作温度范围 Operation Temperature range -30～85℃ 12 储存温度范围 Storage Temperature range -40～85℃
BT-MC88-1X Specification 24 管脚配置 No. 名称 Pin Name I/O 接口类型 Pad Type 描述 Pin Description 1 GND - VSS Ground of supply voltage 2 SPI_CS#/PCM_SYNC I/O Bi-directional, Tristate, with weak internal pull-down SPI chip select(active low) or PCM synchronous data sync 3 SPI_MISO/PCM_OUT O Output, Tristate, with weak internal pull-down SPI data output or PCM synchronous data output 4 SPI_CLK/PCM_CLK I/O Bi-directional, Tristate, with weak internal pull-down SPI clock or PCM synchronous data-clock 5 SPI_MOSI/PCM_IN I Input, Tristate, with weak internal pull-down SPI data input or PCM synchronous data input 6 SPI_PCM#_SEL I Input with weak internal pull-down Control line to select SPI or PCM interface, H=SPI, L=PCM 7 RESET# I Input with strong internal pull-down Active low reset, to ensure a full reset the reset sigma should be asserted for period greater than 5ms. 8 VDD_3V3 I VDD Positive supply for module, -Supply voltage: Typical 3.3V 9 VDD_PADS I VDD Positive supply for module, -Supply voltage: Typical 3.3V 10 GND - VSS Ground of supply voltage 11 I2C_SDA I/O Bi-directional, Tristate EEPROM data pin, Internal 4.7K pull-up resistor 12 I2C_SCL I Input clock EEPROM clock pin, Internal 4.7K pull-up resistor 13 I2C_WP I Write protect input EEPROM write protect pin, Internal 4.7K pull-up resistor 14 VDD_1V8 I VDD Output from internal high-voltage regulator 15 GND - VSS Ground of supply voltage 16 UART_CTS I Bi-directional, Tristate, with weak internal pull-up UART clear to send, active low 17 UART_RTS O Bi-directional, Tristate, with weak internal pull-up UART request to send, active low. 18 UART_RX I Bi-directional, Tristate, with weak internal pull-up UART data input, active high -Recommended external 10K pull-up resistor. 19 UART_TX O Bi-directional, Tristate, with weak internal pull-up UART data output, active high -Recommended external 10K pull-up resistor. 20 GND - VSS Ground of supply voltage 21 NC - NC NC 22 NC - NC NC 23 NC - NC NC 24 GND - VSS Ground of supply voltage 备注：建议PCM,I2C以及 UART都串联一个10Ω-1K的外置电阻 Remark: Recommended external 10Ω-1K serial resistor for all the PCM, I2C and UART transfer ports.
BT-MC88-1X Specification 35 模组尺寸 Module Dimension 模块尺寸 23*16*3.2mm(长*宽*高) 公差: ±0.1mm Module Size：23*16*3.2mm (L*W*H) tolerance: ±0.1mm 6试验规格 Routine Test Specification 序号 No. 测试项目 Test Item 测试条件 Conditions 换1 高温存储 High Temperature (Storage) 在+85℃环境下放置 48 小时，在标准测试条件下三小时内进行测试，模块应满足可靠性测试标准 +85℃, 48hrs, In standard test condition take measurements within 3 hours. 2 低温存储 Low Temperature (Storage) 在-40±3℃环境下放置 48 小时，在标准测试条件下三小时内进行测试，模块应满足可靠性测试标准 -40±3℃,48hrs, In standard test condition, take measurements within 3 hours 3 高湿存储 High Humidity (Storage) 在40±3℃,90±5%RH 环境中放置 48 小时，在标准测试条件下三小时内进行测试，模块应满足可靠性测试标准 40±3℃,90±5%RH, 48hrs, In standard test condition, take measurements within 3 hours 4 高低温循环 High and low temperature cycling test 在+85℃环境下放置 30 分钟，然后温度降低到到-40℃（温度转换时间为 2个小时）放置 30 分钟；然后温度升高到 85℃放置 30 分钟（温度转换时间为 2个小时），如此重复循环 5次。实验完成后，在标准测试条件下，模块应满足可靠性测试标准 Tstg Max 85℃ 30 min s, Temperature shift time: within 2hrs. Tstg Min -40℃ 30 min s. 5 cycles 5 热冲击 Thermal Shock 在+85℃环境下放置 20 分钟后，温度切换到-40℃（在 5分钟之内）放置 20 分钟，然后温度切换到 85℃（在 5分钟之内）放置 20 分钟，如此重复循环 5次，实验完成后，在标准测试条件下，模块应满足基本功能
BT-MC88-1X Specification 4Tstg Max 85℃ 20 mins, Temperature shift time: within 5 mins. Tstg Min -40℃ 20 mins. 50 cycles 6 静电测试 Electrostatic Resistance 人体接触放电 ±2KV，3次，静电测试后，在标准测条件下，模块应满足基本功能 human body model ±2KV, 3 times 7 振动测试 Vibration Resistance 振动频率：10～55Hz，扫频速率：0.1 oct/min，最大加速度：4G。X ，Y，Z三个方向各两个小时，振动完成后，在标准测试条件下三个小时内测试，满足基本功能 Freq: 10~55Hz, 0.1 oct/min, max acceleration: 4Grms- Test time: X,Y, Z axis for 6 hours. After 1 hour vibration test, do the test in each direction. In standard test condition, take measurements within 3 hours. 8 冲击测试 Impact Resistance 冲击测试：冲击加速度：50G(m/sec2)；冲击时间：11 毫秒；冲击频率和方向：6个方向每个方向 10 次。在标准测试条件下三个小时内测试，模块应满足可靠性测试标准 跌落测试：将模块从 100 厘米的高度跌落到一块 10 毫米厚的胶合板上，重复 5次，实验完成后在标准测试条件下，模块应满足基本功能 Shock Test: Impact acceleration: 50G(m/sec2), impact time: 11msec, impact frequency and direction: 10 times each in 6 directions. In standard test condition, take measurements within 3hr. Drop Test: Test height: 100cm. Frequency: 5 times. Drop the module onto 10mm thickness plywood. In standard test condition, take measurements within 3 hours 9 蒸压测试 Pressurizing Vapour 在-30℃环境下放置 1个小时，在 1分钟之内切换至 25℃,90%RH 环境下，放置 1个小时，开启 15 分钟，然后关闭 15 分钟。在标准测试条件下进行 3个循环，实验完成后在常温下放置 2个小时后测试，模块应满足基本功能 -30℃ 1 hour, shift to 25℃,90%RH within 1 min, stay 25℃,90%RH 1 hour, On:15min then Off: 15min. 3 cycle In Standard test condition, take measurements 2 hours after
9. 附录 Appendix9.1 FCC&IC 提示 FCC&IC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following : “Contains Transmitter Module FCC ID: ZWY8350X”or“Contains FCC ID: ZWY8350X.” When the module is installed inside another device,the user manual of this device must contain below warning statements ; 1.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference . (2) this device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. If the IC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains transmitter module IC : 12033A-8811X” or “Contains IC : 12033A-8811X” When the module is installed inside another device, the user manual of this device must contain below warning statements ; This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product.

Navigation menu