Shinwa 8811X Car Kit Bluetooth Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2708545
Application ID	VrhO545hhhSYMFs7quBEig==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.19kB (252341 bits)
Date Submitted	2015-08-09 00:00:00
Date Available	2015-08-09 00:00:00
Creation Date	2015-05-12 15:37:20
Producing Software	Foxit Reader PDF Printer Version 6.1.0.0923
Document Lastmod	2015-08-04 16:34:23
Document Title	User manual

BT-MC88-1X 产品说明书
1. 介绍 Introduction
1.1
1.2
1.3
简要 Overview
★
BT-MC88-1X是 一 款 基 于 CSR8811芯 片 设 计 的 HCI模 组 .
BT-MC88 -1X is a HC I mo dule based on CSR8 811 chip .
★
BT-MC88-1X是 由 一 单 射 频 和 基 带 IC组 成 并 应 用 于 蓝 牙 2.4GHz 系 统 的 模 组 .
The BT-MC88 -1X is a mo dule th at In tegrate a sing le -ch ip radio and baseband IC fo r
Bluetoo th 2 .4GHz syste ms.
特征 Features
★
蓝牙双模/蓝牙低功耗
Dual-mode Blue too th/Blue too th low energ y
★
高品质蓝牙4.0
High qua lity Blueto oth v4.0
★
Class2蓝牙功率等级
Bluetoo th p owe r le ve l： Class 2
★
高速串行通讯接口（最高到4Mbps）
High -spe ed UART port (up to 4Mbp s)
★
PCM/I2S兼容数字音频接口
P CM/I2S d ig ital audio interfaces.
★
支持IEEE 802.11协议
Support fo r IEEE 802. 1 1
★
模组尺寸23*16*3.2mm，邮票孔，24个脚位（带屏蔽罩）
Module size 23 *16 *3.2 mm, S ta mp -24 (with sh ield ca se )
★
模组内置PCB天线
Built-in pa ttern an tenn a on the mod ule
★
标准的HCI通讯接口
Standa rd HC I sup port
★
宽电源供电，电压范围：2.7-3.6V
Flex ible voltag e supp ly, supp ly range : 2.7 -3.6 V
★
环保RoHS
Environ men tal care: Ro HS
应用 Applications
★
车载免提
Hands-Fre e Car Kits
★
低端手机、功能手机、智能手机
Low-co st p hones, Fea tu re phone s, S mart-p hone s
★
便携式媒体播放器
P ortable med ia p la ye rs
BT-MC88-1X Specification
2.规格 参数
产品或项目名称 Product/ Project Name
车载蓝牙模组 Car kit Bluetooth Module
芯片类型 Chip set
BlueCore CSR8811 A08 0.5mm WLCSP
产品射频功率等级 Power class level
Class 2 (-6dBm < PAV < 4dBm)
波特率 Baud Rate
9600bps～4Mbps
额定电压 Rated Voltage
3.3V
工作电压范围 Operation Voltage range
2.7V～3.6V
工作范围 Operation Range
10 meters (33 feet)
尺寸 Dimension
23*16*3.2mm （L*W*H）
核心规格版本 Core Specification Version
10
认证 Test of certification
FCC\CE\IC\MIC\BQB
11
工作温度范围 Operation Temperature range
-30～85℃
12
储存温度范围 Storage Temperature range
-40～85℃
□1.2
□2.0
□2.0+EDR □2.1
□2.1+EDR
■3.0
□3.0+HS
■4.0
3 射频规格 RF Spe
规格
Specification
输出功率
Output transmit power
调制特性
Modulation characteristics
初始载波频率容限
Initial carrier-frequency tolerance
载波频率漂移
Carrier frequency drift
条件
Condition
最小
Min.
典型
Type
最大
Max.
单位
Unit
Normal
-6
dBm
175
kHz
f1 avg
140
f2 max
115
kHz
f2avg/f1a
vg
80
Normal
-20
20
kHz
DH1
-25
25
kHz
DH3
-40
40
kHz
DH5
-40
40
kHz
Draft rate/50us
-20
20
kHz
备注：常温下是25±5℃
Remark: Normal Test Condition is 25±5℃
BT-MC88-1X Specification
4 管脚配置
名称 Pin Name
No.
GND
SPI_CS#/PCM_SYN
SPI_MISO/PCM_OU
接口类型 Pad Type
I/O
I/O
描述 Pin Description
VSS
Ground of supply voltage
Bi-directional, Tristate, with
SPI chip select(active low) or PCM synchronous data
weak internal pull-down
sync
Output, Tristate, with weak
internal pull-down
Bi-directional, Tristate, with
SPI data output or PCM synchronous data output
SPI_CLK/PCM_CLK
I/O
SPI_MOSI/PCM_IN
SPI_PCM#_SEL
RESET#
VDD_3V3
VDD
VDD_PADS
VDD
10
GND
VSS
Ground of supply voltage
11
I2C_SDA
I/O
Bi-directional, Tristate
EEPROM data pin, Internal 4.7K pull-up resistor
12
I2C_SCL
Input clock
EEPROM clock pin, Internal 4.7K pull-up resistor
13
I2C_WP
Write protect input
EEPROM write protect pin, Internal 4.7K pull-up resistor
14
VDD_1V8
VDD
Output from internal high-voltage regulator
15
GND
VSS
Ground of supply voltage
16
UART_CTS
17
UART_RTS
18
UART_RX
19
UART_TX
20
GND
21
weak internal pull-down
Input, Tristate, with weak
internal pull-down
SPI clock or PCM synchronous data-clock
SPI data input or PCM synchronous data input
Input with weak internal
Control line to select SPI or PCM interface,
pull-down
L=PCM
Input with strong internal
Active low reset, to ensure a full reset the reset sigma
pull-down
should be asserted for period greater than 5ms.
Bi-directional, Tristate, with
weak internal pull-up
Bi-directional, Tristate, with
weak internal pull-up
H=SPI,
Positive supply for module,
-Supply voltage: Typical 3.3V
Positive supply for module,
-Supply voltage: Typical 3.3V
UART clear to send, active low
UART request to send, active low.
Bi-directional, Tristate, with
UART data input, active high
weak internal pull-up
-Recommended external 10K pull-up resistor.
Bi-directional, Tristate, with
UART data output, active high
weak internal pull-up
-Recommended external 10K pull-up resistor.
VSS
Ground of supply voltage
NC
NC
NC
22
NC
NC
NC
23
NC
NC
NC
24
GND
VSS
Ground of supply voltage
备注：建议PCM,I2C以及 UART都串联一个10Ω-1K的外置电阻
Remark: Recommended external 10Ω-1K serial resistor for all the PCM, I2C and UART transfer ports.
BT-MC88-1X Specification
5 模组尺寸 Module Dimension
模块尺寸 23*16*3.2mm(长*宽*高) 公差: ±0.1mm
Module Size：23*16*3.2mm (L*W*H) tolerance: ±0.1mm
6 试验规格 Routine Test Specification
序号
测试项目
测试条件
No.
Test Item
Conditions
高温存储
换
High Temperature (Storage)
在+85℃环境下放置 48 小时，在标准测试条件下三小时内进行测试，模块应满足可
靠性测试标准
+85℃, 48hrs, In standard test condition take measurements within 3 hours.
低温存储
在-40±3℃环境下放置 48 小时，在标准测试条件下三小时内进行测试，模块应满足
Low Temperature (Storage)
可靠性测试标准
-40±3℃,48hrs, In standard test condition, take measurements within 3 hours
高湿存储
在 40±3℃,90±5%RH 环境中放置 48 小时，在标准测试条件下三小时内进行测试，
High Humidity (Storage)
模块应满足可靠性测试标准
40±3℃,90±5%RH, 48hrs, In standard test condition, take measurements within 3 hours
高低温循环
在+85℃环境下放置 30 分钟，然后温度降低到到-40℃（温度转换时间为 2 个小时）
High and low temperature
放置 30 分钟；然后温度升高到 85℃放置 30 分钟（温度转换时间为 2 个小时），如
cycling test
此重复循环 5 次。实验完成后，在标准测试条件下，模块应满足可靠性测试标准
Tstg Max 85℃ 30 min s, Temperature shift time: within 2hrs. Tstg Min -40℃ 30 min s.
5 cycles
热冲击
在+85℃环境下放置 20 分钟后，温度切换到-40℃（在 5 分钟之内）放置 20 分钟，
Thermal Shock
然后温度切换到 85℃（在 5 分钟之内）放置 20 分钟，如此重复循环 5 次，实验完
成后，在标准测试条件下，模块应满足基本功能
BT-MC88-1X Specification
Tstg Max 85℃ 20 mins, Temperature shift time: within 5 mins. Tstg Min -40℃ 20
mins. 50 cycles
静电测试
人体接触放电 ±2KV，3 次，静电测试后，在标准测条件下，模块应满足基本功能
Electrostatic Resistance
human body model ±2KV, 3 times
振动测试
振动频率：10～55Hz，扫频速率：0.1 oct/min，最大加速度：4G。X ，Y，Z 三个
Vibration Resistance
方向各两个小时，振动完成后，在标准测试条件下三个小时内测试，满足基本功能
Freq: 10~55Hz, 0.1 oct/min, max acceleration: 4Grms- Test time: X,Y, Z axis for 6
hours. After 1 hour vibration test, do the test in each direction. In standard test condition,
take measurements within 3 hours.
冲击测试
冲击测试：冲击加速度：50G(m/sec2)；冲击时间：11 毫秒；冲击频率和方向：6
Impact Resistance
个方向每个方向 10 次。在标准测试条件下三个小时内测试，模块应满足可靠性测
试标准
跌落测试：将模块从 100 厘米的高度跌落到一块 10 毫米厚的胶合板上，
重复 5 次，实验完成后在标准测试条件下，模块应满足基本功能
Shock Test: Impact acceleration: 50G(m/sec2), impact time: 11msec, impact frequency
and direction: 10 times each in 6 directions. In standard test condition, take
measurements within 3hr. Drop Test: Test height: 100cm. Frequency: 5 times. Drop the
module onto 10mm thickness plywood. In standard test condition, take measurements
within 3 hours
蒸压测试
在-30℃环境下放置 1 个小时，在 1 分钟之内切换至 25℃,90%RH 环境下，放置 1
Pressurizing Vapour
个小时，开启 15 分钟，然后关闭 15 分钟。在标准测试条件下进行 3 个循环，实验
完成后在常温下放置 2 个小时后测试，模块应满足基本功能
-30℃ 1 hour, shift to 25℃,90%RH within 1 min, stay 25℃,90%RH 1 hour, On:15min
then Off: 15min. 3 cycle In Standard test condition, take measurements 2 hours after
9. 附录 Appendix
9.1 FCC&IC 提示 FCC&IC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
If the FCC identification number is not visible when the module is installed inside another device, then
the outside of the device into which the module is installed must also display a label referring to the
enclosed module. This exterior label can use wording such as the following : “Contains Transmitter
Module FCC ID: ZWY8350X”or“Contains FCC ID: ZWY8350X.”
When the module is installed inside another device,the user manual of this device must contain below
warning statements ;
1.This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference .
(2) this device must accept any interference received, including interference that may cause undesired
operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
The devices must be installed and used in strict accordance with the manufacturer’s instructions as
described in the user documentation that comes with the product.
If the IC identification number is not visible when the module is installed inside another device, then
the outside of the device into which the module is installed must also display a label referring to the
enclosed module. This exterior label can use wording such as the following: “Contains transmitter
module IC : 12033A-8811X” or “Contains IC : 12033A-8811X”
When the module is installed inside another device, the user manual of this device must contain below
warning statements ;
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
The devices must be installed and used in strict accordance with the manufacturer’s instructions as
described in the user documentation that comes with the product.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : 
Description                     : 
Title                           : 
Create Date                     : 2015:05:12 15:37:20+08:00
Creator Tool                    : 
Modify Date                     : 2015:08:04 16:34:23+08:00
Metadata Date                   : 2015:08:04 16:34:23+08:00
Keywords                        : 
Producer                        : Foxit Reader PDF Printer Version 6.1.0.0923
Document ID                     : uuid:32484a0f-4350-4e88-9ff4-b07e13a7385f
Instance ID                     : uuid:f74882e5-9a99-446a-a3fb-de0524540e6d
Page Count                      : 7
Author                          : 
Subject                         : 

EXIF Metadata provided by EXIF.tools