Siemens RF280R RFID Reader 13.56 MHz User Manual SIMATIC RF200
Siemens AG RFID Reader 13.56 MHz SIMATIC RF200
Siemens >
Contents
- 1. SYH_RF200_76_Part 1
- 2. SYH_RF200_76_Part 2
- 3. SYH_RF200_76_Part 3
SYH_RF200_76_Part 1
Introduction Safety notes SIMATIC Ident System overview RFID systems SIMATIC RF200 Planning the RF200 system Readers Antennas Transponder System integration System diagnostics Appendix System Manual 07/2017 J31069-D0227-U001-A9-7619 Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe personal injury will result if proper precautions are not taken. WARNING indicates that death or severe personal injury may result if proper precautions are not taken. CAUTION indicates that minor personal injury can result if proper precautions are not taken. NOTICE indicates that property damage can result if proper precautions are not taken. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage. Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems. Proper use of Siemens products Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed. Trademarks All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. Siemens AG Division Process Industries and Drives Postfach 48 48 90026 NÜRNBERG GERMANY Ⓟ 07/2017 Subject to change Copyright © Siemens AG 2010 - 2017. All rights reserved Table of contents Introduction ........................................................................................................................................... 13 1.1 Abbreviations and naming conventions ..................................................................................14 Safety notes .......................................................................................................................................... 15 System overview ................................................................................................................................... 19 3.1 RFID components and their function ......................................................................................20 3.2 Overview of transponders .......................................................................................................23 Planning the RF200 system .................................................................................................................. 27 4.1 4.1.1 4.1.2 4.1.3 4.1.4 4.1.5 4.1.6 4.1.7 4.1.8 Fundamentals of application planning ....................................................................................27 Selection criteria for SIMATIC RF200 components ................................................................27 Transmission window and read/write distance .......................................................................27 Width of the transmission window ..........................................................................................30 Impact of secondary fields ......................................................................................................31 Permissible directions of motion of the transponder ...............................................................34 Operation in static and dynamic mode ...................................................................................35 Dwell time of the transponder .................................................................................................36 Communication between communication module, reader and transponder ..........................37 4.2 4.2.1 4.2.2 Field data of transponders and readers ..................................................................................38 Field data ................................................................................................................................39 Minimum clearances ...............................................................................................................48 4.3 4.3.1 4.3.2 4.3.3 4.3.4 4.3.4.1 4.3.4.2 4.3.4.3 4.3.4.4 4.3.4.5 4.3.4.6 4.3.4.7 4.3.5 4.3.5.1 4.3.5.2 4.3.5.3 4.3.6 4.3.6.1 4.3.6.2 Installation guidelines..............................................................................................................50 Overview .................................................................................................................................50 Reduction of interference due to metal ...................................................................................51 Effects of metal on different transponders and readers ..........................................................53 Impact of metal on the transmission window ..........................................................................54 RF210R ...................................................................................................................................55 RF220R ...................................................................................................................................58 RF240R ...................................................................................................................................60 RF250R ...................................................................................................................................63 RF260R ...................................................................................................................................71 RF280R ...................................................................................................................................74 RF290R ...................................................................................................................................76 Installation and connection of 2 to 6 antennas with one RF290R reader ...............................80 Installation options with the antenna splitter (2-4 antennas) ..................................................80 Antenna installation.................................................................................................................84 Installation options with the antenna multiplexer (2-6 antennas) ...........................................88 Chemical resistance of the reader and transponders .............................................................89 Readers ..................................................................................................................................89 Transponder ............................................................................................................................93 4.4 Further information................................................................................................................101 SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Table of contents Readers ...............................................................................................................................................103 5.1 5.1.1 5.1.2 5.1.3 5.1.4 5.1.5 5.1.6 5.1.7 5.1.8 SIMATIC RF210R ................................................................................................................ 104 Features ............................................................................................................................... 104 RF210R ordering data ......................................................................................................... 104 Pin assignment RF210R with RS422 interface .................................................................... 105 LED operating display .......................................................................................................... 105 Minimum distance between RF210R readers ...................................................................... 106 Technical specifications of the RF210R reader ................................................................... 107 Approvals ............................................................................................................................. 108 Dimension drawing .............................................................................................................. 109 5.2 5.2.1 5.2.2 5.2.3 5.2.4 5.2.5 5.2.6 5.2.7 5.2.8 SIMATIC RF210M ................................................................................................................ 110 Features ............................................................................................................................... 110 Ordering data RF210M ........................................................................................................ 110 Installing the RF210M reader............................................................................................... 111 Pin assignment RF210M with RS-422 interface .................................................................. 112 LED operating display .......................................................................................................... 112 Technical specifications of the RF210M reader ................................................................... 113 Approvals ............................................................................................................................. 114 Dimension drawing .............................................................................................................. 115 5.3 5.3.1 5.3.2 5.3.3 5.3.4 5.3.5 5.3.6 5.3.7 5.3.8 SIMATIC RF220R ................................................................................................................ 116 Features ............................................................................................................................... 116 RF220R ordering data ......................................................................................................... 116 RF220R pin assignment with RS422 interface .................................................................... 117 LED operating display .......................................................................................................... 117 Minimum distance between RF220R readers ...................................................................... 118 Technical specifications of the RF220R reader ................................................................... 119 Approvals ............................................................................................................................. 120 Dimension drawing .............................................................................................................. 121 5.4 5.4.1 5.4.2 5.4.3 5.4.4 5.4.5 5.4.6 5.4.7 5.4.8 SIMATIC RF240R ................................................................................................................ 122 Features ............................................................................................................................... 122 RF240R ordering data ......................................................................................................... 122 Pin assignment RF240R ...................................................................................................... 123 LED operating display .......................................................................................................... 123 Minimum distance between several RF240R readers ......................................................... 124 Technical specifications of the RF240R reader ................................................................... 125 Approvals ............................................................................................................................. 127 Dimension drawing .............................................................................................................. 128 5.5 5.5.1 5.5.2 5.5.3 5.5.4 5.5.5 5.5.6 5.5.7 SIMATIC RF250R ................................................................................................................ 128 Features ............................................................................................................................... 128 Ordering data RF250R ......................................................................................................... 129 Pin assignment RF250R ...................................................................................................... 129 LED operating display .......................................................................................................... 129 Technical specifications of the RF250R reader ................................................................... 130 Approvals ............................................................................................................................. 131 Dimension drawing .............................................................................................................. 133 5.6 5.6.1 5.6.2 5.6.3 SIMATIC RF260R ................................................................................................................ 134 Features ............................................................................................................................... 134 Ordering data for RF260R ................................................................................................... 134 Pin assignment RF260R ...................................................................................................... 135 SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Table of contents 5.6.4 5.6.5 5.6.6 5.6.7 5.6.8 LED operating display ...........................................................................................................135 Minimum distance between several RF260R .......................................................................136 Technical data of the RF260R reader...................................................................................137 Approvals ..............................................................................................................................138 Dimension drawing ...............................................................................................................139 5.7 5.7.1 5.7.2 5.7.3 5.7.4 5.7.5 5.7.6 5.7.7 5.7.8 SIMATIC RF280R .................................................................................................................140 Features ................................................................................................................................140 Ordering data RF280R..........................................................................................................140 Pin assignment RF280R .......................................................................................................141 LED operating display ...........................................................................................................141 Minimum distance between RF280R readers ......................................................................142 Technical specifications of the RF280R reader ....................................................................143 Approvals ..............................................................................................................................144 Dimension drawing ...............................................................................................................146 5.8 5.8.1 5.8.2 5.8.3 5.8.4 5.8.5 5.8.5.1 5.8.5.2 5.8.5.3 5.8.6 5.8.7 5.8.8 5.8.9 SIMATIC RF290R .................................................................................................................147 Features ................................................................................................................................147 Ordering data RF290R..........................................................................................................147 Pin assignment RF290R .......................................................................................................149 LED operating display ...........................................................................................................151 Installing the RF290R reader ................................................................................................152 Wall mounting .......................................................................................................................152 Installing on the S7-300 standard rail ...................................................................................153 Installation on a DIN rail ........................................................................................................153 Technical specifications of the RF290R reader ....................................................................155 Approvals ..............................................................................................................................156 Note on the use of the RF290R as a replacement for SLG D10 / SLG D10S ......................158 Dimension drawing ...............................................................................................................159 Antennas ............................................................................................................................................ 161 6.1 6.1.1 6.1.2 6.1.3 6.1.4 6.1.5 6.1.6 6.1.7 ANT 1 ....................................................................................................................................161 Characteristics ......................................................................................................................161 Ordering data ........................................................................................................................161 Flush-mounted in metal ........................................................................................................162 Operating / limit distances ....................................................................................................162 Minimum clearances .............................................................................................................163 Technical specifications ........................................................................................................164 Dimension drawing ...............................................................................................................165 6.2 6.2.1 6.2.2 6.2.3 6.2.4 6.2.5 6.2.6 6.2.7 ANT 3 ....................................................................................................................................166 Features ................................................................................................................................166 Ordering data ........................................................................................................................166 Mounting on/in metal.............................................................................................................167 Operating / limit distances ....................................................................................................168 Minimum spacing ..................................................................................................................169 Technical data .......................................................................................................................170 Dimension drawing ...............................................................................................................171 6.3 6.3.1 6.3.2 6.3.3 6.3.4 ANT 8 ....................................................................................................................................172 Features ................................................................................................................................172 Ordering data ........................................................................................................................172 Transmission window............................................................................................................173 Flush-mounted in metal ........................................................................................................173 SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Table of contents 6.3.5 6.3.6 6.3.7 Minimum spacing ................................................................................................................. 174 Technical data ...................................................................................................................... 175 Dimension drawing .............................................................................................................. 176 6.4 6.4.1 6.4.2 6.4.3 6.4.4 6.4.5 6.4.6 6.4.7 ANT 12 ................................................................................................................................. 177 Features ............................................................................................................................... 177 Ordering data ....................................................................................................................... 177 Transmission window ........................................................................................................... 178 Flush-mounted in metal ....................................................................................................... 178 Minimum spacing ................................................................................................................. 179 Technical data ...................................................................................................................... 180 Dimension drawing .............................................................................................................. 181 6.5 6.5.1 6.5.2 6.5.3 6.5.4 6.5.5 6.5.6 6.5.7 ANT 18 ................................................................................................................................. 182 Features ............................................................................................................................... 182 Ordering data ....................................................................................................................... 182 Transmission window ........................................................................................................... 183 Flush-mounted in metal ....................................................................................................... 183 Minimum spacing ................................................................................................................. 184 Technical data ...................................................................................................................... 185 Dimension drawing .............................................................................................................. 186 6.6 6.6.1 6.6.2 6.6.3 6.6.4 6.6.5 6.6.6 6.6.7 ANT 30 ................................................................................................................................. 187 Features ............................................................................................................................... 187 Ordering data ....................................................................................................................... 187 Transmission window ........................................................................................................... 188 Flush-mounted in metal ....................................................................................................... 189 Minimum spacing ................................................................................................................. 189 Technical data ...................................................................................................................... 190 Dimension drawing .............................................................................................................. 191 6.7 6.7.1 6.7.2 6.7.3 6.7.4 6.7.5 6.7.6 6.7.7 ANT D5 ................................................................................................................................ 192 Features ............................................................................................................................... 192 Ordering data ....................................................................................................................... 192 Transmission window ........................................................................................................... 193 Flush-mounted in metal ....................................................................................................... 194 Minimum spacing ................................................................................................................. 194 Technical data ...................................................................................................................... 195 Dimension drawing .............................................................................................................. 197 6.8 6.8.1 6.8.2 6.8.3 6.8.4 6.8.5 6.8.6 6.8.7 ANT D6 ................................................................................................................................ 198 Features ............................................................................................................................... 198 Ordering data ....................................................................................................................... 198 Transmission window ........................................................................................................... 199 Metal-free area ..................................................................................................................... 200 Minimum spacing ................................................................................................................. 200 Technical data ...................................................................................................................... 201 Dimensional diagram ........................................................................................................... 202 6.9 6.9.1 6.9.2 6.9.3 6.9.4 6.9.5 ANT D10 .............................................................................................................................. 203 Features ............................................................................................................................... 203 Ordering data ....................................................................................................................... 203 Transmission window ........................................................................................................... 204 Metal-free area ..................................................................................................................... 205 Minimum spacing ................................................................................................................. 206 SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Table of contents 6.9.6 6.9.7 Technical data .......................................................................................................................206 Dimensional diagram ............................................................................................................208 Transponder ....................................................................................................................................... 209 7.1 Memory configuration of ISO the transponders ....................................................................209 7.2 7.2.1 7.2.2 7.2.3 7.2.4 7.2.5 MDS D100 ............................................................................................................................210 Characteristics ......................................................................................................................210 Ordering data ........................................................................................................................210 Metal-free area ......................................................................................................................211 Technical data .......................................................................................................................212 Dimension drawing ...............................................................................................................214 7.3 7.3.1 7.3.2 7.3.3 7.3.4 7.3.5 MDS D117 ............................................................................................................................215 Features ................................................................................................................................215 Ordering data ........................................................................................................................215 Mounting in metal..................................................................................................................215 Technical specifications ........................................................................................................216 Dimension drawing ...............................................................................................................217 7.4 7.4.1 7.4.2 7.4.3 7.4.4 7.4.5 7.4.6 MDS D124 ............................................................................................................................218 Characteristics ......................................................................................................................218 Ordering data ........................................................................................................................218 Mounting on metal ................................................................................................................219 Technical specifications ........................................................................................................220 Use of the MDS D124 in hazardous area .............................................................................221 Dimension drawing ...............................................................................................................223 7.5 7.5.1 7.5.2 7.5.3 7.5.4 7.5.5 MDS D126 ............................................................................................................................224 Characteristics ......................................................................................................................224 Ordering data ........................................................................................................................224 Mounting on metal ................................................................................................................225 Technical specifications ........................................................................................................226 Dimension drawing ...............................................................................................................227 7.6 7.6.1 7.6.2 7.6.3 7.6.4 7.6.5 MDS D127 ............................................................................................................................228 Features ................................................................................................................................228 Ordering data ........................................................................................................................228 Mounting in metal..................................................................................................................229 Technical specifications ........................................................................................................230 Dimension drawing ...............................................................................................................231 7.7 7.7.1 7.7.2 7.7.3 7.7.4 7.7.5 7.7.6 7.7.7 7.7.8 MDS D139 ............................................................................................................................232 Characteristics ......................................................................................................................232 Ordering data ........................................................................................................................232 Metal-free area ......................................................................................................................233 Mounting in metal..................................................................................................................234 Cleaning the transponder .....................................................................................................234 Technical specifications ........................................................................................................235 Use of the MDS D139 in hazardous areas ...........................................................................236 Dimension drawings..............................................................................................................238 7.8 7.8.1 7.8.2 7.8.3 MDS D160 ............................................................................................................................239 Characteristics ......................................................................................................................239 Ordering data ........................................................................................................................239 Mounting on metal ................................................................................................................240 SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Table of contents 7.8.4 7.8.5 Technical specifications ....................................................................................................... 240 Dimension drawings ............................................................................................................. 242 7.9 7.9.1 7.9.2 7.9.3 7.9.4 MDS D165............................................................................................................................ 243 Features ............................................................................................................................... 243 Ordering data ....................................................................................................................... 243 Technical data ...................................................................................................................... 244 Dimension drawing .............................................................................................................. 245 7.10 7.10.1 7.10.2 7.10.3 7.10.4 7.10.5 MDS D200............................................................................................................................ 246 Features ............................................................................................................................... 246 Ordering data ....................................................................................................................... 246 Mounting on metal ............................................................................................................... 247 Technical data ...................................................................................................................... 248 Dimension drawing .............................................................................................................. 250 7.11 7.11.1 7.11.2 7.11.3 7.11.4 MDS D261............................................................................................................................ 250 Features ............................................................................................................................... 250 Ordering data ....................................................................................................................... 250 Technical data ...................................................................................................................... 251 Dimension drawing .............................................................................................................. 252 7.12 7.12.1 7.12.2 7.12.3 7.12.4 7.12.5 MDS D324............................................................................................................................ 253 Characteristics ..................................................................................................................... 253 Ordering data ....................................................................................................................... 253 Mounting on metal ............................................................................................................... 254 Technical specifications ....................................................................................................... 255 Dimension drawing .............................................................................................................. 256 7.13 7.13.1 7.13.2 7.13.3 7.13.4 7.13.5 7.13.6 7.13.7 7.13.8 MDS D339............................................................................................................................ 257 Characteristics ..................................................................................................................... 257 Ordering data ....................................................................................................................... 257 Mounting on metal ............................................................................................................... 258 Mounting in metal ................................................................................................................. 259 Cleaning the transponder ..................................................................................................... 259 Technical specifications ....................................................................................................... 260 Use of the MDS D339 in hazardous areas .......................................................................... 261 Dimensional drawing ............................................................................................................ 263 7.14 7.14.1 7.14.2 7.14.3 7.14.4 7.14.5 MDS D400............................................................................................................................ 264 Features ............................................................................................................................... 264 Ordering data ....................................................................................................................... 264 Mounting on metal ............................................................................................................... 265 Technical specifications ....................................................................................................... 266 Dimension drawing .............................................................................................................. 268 7.15 7.15.1 7.15.2 7.15.3 7.15.4 7.15.5 MDS D421............................................................................................................................ 269 Characteristics ..................................................................................................................... 269 Ordering data ....................................................................................................................... 269 Mounting on metal ............................................................................................................... 270 Technical specifications ....................................................................................................... 272 Dimension drawing .............................................................................................................. 273 7.16 7.16.1 7.16.2 MDS D422............................................................................................................................ 274 Characteristics ..................................................................................................................... 274 Ordering data ....................................................................................................................... 274 SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Table of contents 7.16.3 7.16.4 7.16.5 Mounting in metal..................................................................................................................274 Technical specifications ........................................................................................................275 Dimension drawing ...............................................................................................................276 7.17 7.17.1 7.17.2 7.17.3 7.17.4 7.17.5 MDS D423 ............................................................................................................................277 Characteristics ......................................................................................................................277 Ordering data ........................................................................................................................277 Mounting on metal ................................................................................................................277 Technical specifications ........................................................................................................279 Dimensional drawing.............................................................................................................281 7.18 7.18.1 7.18.2 7.18.3 7.18.4 7.18.5 MDS D424 ............................................................................................................................281 Characteristics ......................................................................................................................281 Ordering data ........................................................................................................................282 Mounting on metal ................................................................................................................282 Technical specifications ........................................................................................................283 Dimension drawing ...............................................................................................................285 7.19 7.19.1 7.19.2 7.19.3 7.19.4 7.19.5 MDS D425 ............................................................................................................................285 Characteristics ......................................................................................................................285 Ordering data ........................................................................................................................286 Application example ..............................................................................................................286 Technical specifications ........................................................................................................286 Dimension drawing ...............................................................................................................288 7.20 7.20.1 7.20.2 7.20.3 7.20.4 7.20.5 MDS D426 ............................................................................................................................288 Characteristics ......................................................................................................................288 Mounting on metal ................................................................................................................289 Ordering data ........................................................................................................................290 Technical specifications ........................................................................................................290 Dimension drawing ...............................................................................................................291 7.21 7.21.1 7.21.2 7.21.3 7.21.4 7.21.5 MDS D428 ............................................................................................................................292 Characteristics ......................................................................................................................292 Ordering data ........................................................................................................................292 Application example ..............................................................................................................293 Technical specifications ........................................................................................................293 Dimension drawing ...............................................................................................................295 7.22 7.22.1 7.22.2 7.22.3 7.22.4 7.22.5 MDS D460 ............................................................................................................................295 Characteristics ......................................................................................................................295 Ordering data ........................................................................................................................296 Mounting on metal ................................................................................................................296 Technical specifications ........................................................................................................297 Dimension drawings..............................................................................................................298 7.23 7.23.1 7.23.2 7.23.3 7.23.4 7.23.5 MDS D521 ............................................................................................................................299 Characteristics ......................................................................................................................299 Ordering data ........................................................................................................................299 Mounting on metal ................................................................................................................299 Technical specifications ........................................................................................................301 Dimension drawing ...............................................................................................................303 7.24 7.24.1 7.24.2 MDS D522 ............................................................................................................................303 Characteristics ......................................................................................................................303 Ordering data ........................................................................................................................304 SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Table of contents 7.24.3 7.24.4 7.24.5 Mounting in metal ................................................................................................................. 304 Technical specifications ....................................................................................................... 305 Dimension drawing .............................................................................................................. 306 7.25 7.25.1 7.25.2 7.25.3 7.25.4 7.25.5 7.25.6 MDS D522 special variant ................................................................................................... 307 Characteristics ..................................................................................................................... 307 Ordering data ....................................................................................................................... 307 Mounting in metal ................................................................................................................. 308 Installation instructions ......................................................................................................... 308 Technical specifications ....................................................................................................... 310 Dimensional drawing ............................................................................................................ 311 7.26 7.26.1 7.26.2 7.26.3 7.26.4 7.26.5 MDS D524............................................................................................................................ 312 Characteristics ..................................................................................................................... 312 Ordering data ....................................................................................................................... 312 Mounting on metal ............................................................................................................... 313 Technical specifications ....................................................................................................... 314 Dimension drawing .............................................................................................................. 315 7.27 7.27.1 7.27.2 7.27.3 7.27.4 7.27.5 MDS D526............................................................................................................................ 316 Characteristics ..................................................................................................................... 316 Ordering data ....................................................................................................................... 316 Mounting on metal ............................................................................................................... 317 Technical specifications ....................................................................................................... 318 Dimension drawing .............................................................................................................. 319 7.28 7.28.1 7.28.2 7.28.3 7.28.4 7.28.5 MDS D528............................................................................................................................ 320 Characteristics ..................................................................................................................... 320 Ordering data ....................................................................................................................... 320 Application example ............................................................................................................. 321 Technical specifications ....................................................................................................... 321 Dimension drawing .............................................................................................................. 323 System integration ...............................................................................................................................325 System diagnostics ..............................................................................................................................329 9.1 Error codes of the RF200 readers ....................................................................................... 329 9.2 9.2.1 9.2.2 Diagnostics functions - STEP 7 ........................................................................................... 331 Reader diagnostics with "Reader Status" (SLG Status) ...................................................... 331 Transponder diagnostics with "Tag Status" (MDS Status) .................................................. 333 Appendix .............................................................................................................................................335 A.1 Certificates & approvals ....................................................................................................... 335 A.2 A.2.1 A.2.2 A.2.2.1 A.2.2.2 A.2.2.3 A.2.2.4 A.2.2.5 A.2.2.6 A.2.2.7 A.2.2.8 Accessories .......................................................................................................................... 337 Antenna splitter .................................................................................................................... 337 Antenna multiplexer SIMATIC RF260X ............................................................................... 339 Characteristics ..................................................................................................................... 339 Ordering data ....................................................................................................................... 339 Description ........................................................................................................................... 340 Principle of operation ........................................................................................................... 340 Connectors ........................................................................................................................... 341 Configuration ........................................................................................................................ 342 Parameterization .................................................................................................................. 342 RF260X commands ............................................................................................................. 344 SIMATIC RF200 10 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Table of contents A.2.2.9 A.2.2.10 A.2.3 A.2.3.1 A.2.3.2 A.2.3.3 A.2.3.4 A.2.3.5 A.2.3.6 A.2.3.7 A.2.3.8 A.2.3.9 A.2.4 Technical specifications ........................................................................................................345 Dimensional drawing.............................................................................................................346 Wide-range power supply unit for SIMATIC RF systems .....................................................347 Features ................................................................................................................................347 Scope of supply ....................................................................................................................348 Ordering data ........................................................................................................................348 Safety Information .................................................................................................................348 Connecting ............................................................................................................................349 Technical specifications ........................................................................................................350 Pin assignment of DC outputs and mains connection ..........................................................352 Dimension drawing ...............................................................................................................353 Certificates and approvals ....................................................................................................354 Transponder holders .............................................................................................................355 A.3 A.3.1 A.3.2 A.3.3 A.3.4 A.3.5 Connecting cable ..................................................................................................................361 Reader RF2xxR (RS-422) with ASM 456 / RF160C / RF170C / RF180C / RF182C ...........361 Reader RF2xxR (RS-422) with ASM 475 .............................................................................363 Reader RF2xxR (RS-422) with RF120C...............................................................................364 Reader RF240R/RF260R/RF290R (RS232) with PC ...........................................................364 Reader RF290R ....................................................................................................................366 A.4 Ordering data ........................................................................................................................367 A.5 Service & Support .................................................................................................................377 Index................................................................................................................................................... 379 SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 11 Table of contents SIMATIC RF200 12 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Introduction Introduction SIMATIC RF200 is a compact RFID system in the SIMATIC RFID product family. The product range comprises cost-efficient RF readers that are ideal for use in small assembly lines or in intralogistics. SIMATIC RF200 RFID readers only support the RFID standard ISO 15693 and are therefore ideal for operation with the extensive range of ISO 15693 transponders. The readers of the RF200 product family are available with the following interfaces: ● RS-422 for connecting to the communications modules ● RS-232 with a simple ASCII protocol for connection to PCs and third-party controllers ● IO-Link for connection to IO Link masters from Siemens and third-party controllers Readers with an internal antenna have a particularly compact design (RF210R/RF220R/RF240R/RF260R). RF250R and RF290R are designed for operation with external antennas either to achieve longer distances or larger field sizes (RF290R with ANT D5/D6/D10) or to allow installation where there is very little space (RF250R with ANT 3/8/12/18/30). Scope of validity of this document This documentation is valid for all variants of the SIMATIC RF200 system and describes the devices shipped as of July 2015. Registered trademarks SIMATIC ®, SIMATIC RF ®, MOBY ®, RF MANAGER ® and SIMATIC Sensors ® are registered trademarks of Siemens AG. Further information For additional information, refer to the manuals: ● Function manual "Ident profile and Ident blocks" (https://support.industry.siemens.com/cs/us/en/view/106368029) ● Function manual "FB 45" (https://support.industry.siemens.com/cs/ww/en/view/21738808) ● Operating instructions "RF200 IO-Link" (https://support.industry.siemens.com/cs/ww/en/view/60641859) ● System manual "MOBY D" (https://support.industry.siemens.com/cs/ww/en/view/13628689) SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 13 Introduction 1.1 Abbreviations and naming conventions ● Operating instructions "RF310M" (https://support.industry.siemens.com/cs/us/en/view/51812642) ● Product information "RF200 command set" (https://support.industry.siemens.com/cs/us/en/view/44864850) History The following issues of the SIMATIC RF200 system manual have been published: Output Note 03/2011 First edition 05/2011 Expansion of the documentation with the addition of the device variant RF260R with RS-232 interface 09/2011 Expansion of the documentation with the device variant RF240R 03/2013 Expansion of the documentation with the device variant RF290R 09/2013 Expansion of the documentation by the following: 07/2015 05/2017 1.1 • The device variant RF250R • The device variants RF240R and RF260R with ASCII interface • Antennas ANT 8, ANT 12, ANT 18 and ANT 30 • Transponder Expansion of the documentation by the following: • ANT 3 antennas • MDS D5xx transponder • Mobile reader RF210R Expansion of the documentation by the following: • Device version RF280R • Mobile Reader RF350M Abbreviations and naming conventions Abbreviations and naming conventions The following terms/abbreviations are used synonymously in this document: Reader Write/read device (SLG) Transponder, tag Data carrier, mobile data storage, (MDS) Communications module (CM) Interface module (ASM) SIMATIC RF200 14 System Manual, 07/2017, J31069-D0227-U001-A9-7619 2 Safety notes SIMATIC RFID products comply with the salient safety specifications acc. to IEC, VDE, EN, UL and CSA. If you have questions about the permissibility of the installation in the planned environment, please contact your service representative. WARNING Opening the device Do not open the device when when the power supply is on. Unauthorized opening of and improper repairs to the device may result in substantial damage to equipment or risk of personal injury to the user. NOTICE Alterations not permitted Alterations to the devices are not permitted. Failure to observe this requirement shall constitute a revocation of the radio equipment approval, CE approval and manufacturer's warranty. Installation instructions NOTICE Switch/fuse to disconnect the reader from the power supply Make sure that the readers can be disconnected from the power supply with a switch or a fuse. The function of the switch or fuse must be clearly recognizable. Operating temperature CAUTION Danger of burns Note that some outer components of the reader are made of metal. Depending on the environmental conditions temperatures can occur on the device that are higher than the maximum permitted operating temperature. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 15 Safety notes Repairs WARNING Repairs only by authorized qualified personnel Repairs may only be carried out by authorized qualified personnel. Unauthorized opening of and improper repairs to the device may result in substantial damage to equipment or risk of personal injury to the user. System expansions Only install system expansions intended for this system. If you install other expansions, you may damage the system or violate the safety requirements and regulations for radio frequency interference suppression. Contact Technical Support or your local sales department to find out which system expansions are suitable for installation. NOTICE Warranty conditions If you cause system defects by installing or exchanging system expansion devices, the warranty becomes void. Safety distances CAUTION Safety distance between reader/antenna and persons Note that for permanent exposure, the following safety distances must be adhered to: • RF310R: ≥ 80 mm • RF340R: ≥ 130 mm • RF350R + ANT 1: ≥ 140 mm • RF350R + ANT 3: ≥ 80 mm • RF350R + ANT 12: ≥ 25 mm • RF350R + ANT 18: ≥ 50 mm • RF350R + ANT 30: ≥ 80 mm • RF380R: ≥ 250 mm • RF382R: ≥ 130 mm Note Safety distance with pacemakers A safety distance between reader/antenna and persons with pacemakers is not necessary. SIMATIC RF200 16 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Safety notes Security information Siemens provides products and solutions with industrial security functions that support the secure operation of plants, systems, machines and networks. In order to protect plants, systems, machines and networks against cyber threats, it is necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial security concept. Siemens’ products and solutions only form one element of such a concept. Customer is responsible to prevent unauthorized access to its plants, systems, machines and networks. Systems, machines and components should only be connected to the enterprise network or the internet if and to the extent necessary and with appropriate security measures (e.g. use of firewalls and network segmentation) in place. Additionally, Siemens’ guidance on appropriate security measures should be taken into account. For more information about industrial security, please visit Link: (http://www.siemens.com/industrialsecurity) Siemens’ products and solutions undergo continuous development to make them more secure. Siemens strongly recommends to apply product updates as soon as available and to always use the latest product versions. Use of product versions that are no longer supported, and failure to apply latest updates may increase customer’s exposure to cyber threats. To stay informed about product updates, subscribe to the Siemens Industrial Security RSS Feed under Link: (http://www.siemens.com/industrialsecurity). SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 17 Safety notes SIMATIC RF200 18 System Manual, 07/2017, J31069-D0227-U001-A9-7619 System overview SIMATIC RF200 is an inductive identification system that is compatible with the ISO 15693 standard and was specially designed for use in industrial production for the control and optimization of material flows. In contrast to SIMATIC RF300, SIMATIC RF200 is intended for RFID applications where performance requirements are not very high, for example with regard to data volume, transfer rate or diagnostics options. SIMATIC RF200 is characterized by particularly favorable prices. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 19 System overview 3.1 RFID components and their function 3.1 RFID components and their function RF200 system components Figure 3-1 RF200 system overview SIMATIC RF200 20 System Manual, 07/2017, J31069-D0227-U001-A9-7619 System overview 3.1 RFID components and their function Table 3- 1 Reader-transponder combination options, Part 1 Transponder RF210R/ RF210M RF220R RF240R RF260R RF280R RF290R 4) RF350M MDS D100 -- ○ ✓ ✓ ✓ ✓ ✓ MDS D117 ○ -- -- -- -- -- ✓ 6) MDS D124 ✓ ✓ ✓ ✓ ✓ ✓ ✓ MDS D126 -- ✓ ✓ ✓ ✓ ✓ ✓ MDS D127 ✓ -- -- -- -- -- ✓ 6) MDS D139 1) -- ○ ○ ✓ ✓ ✓ ✓ MDS D160 2) ✓ ✓ ✓ ✓ ✓ ✓ ✓ MDS D165 -- ○ ✓ ✓ ✓ ✓ ✓ MDS D200 -- ○ ✓ ✓ ✓ ✓ ✓ MDS D261 -- ○ ✓ ✓ ✓ ✓ ✓ MDS D324 ✓ ✓ ✓ ✓ ✓ ✓ ✓ MDS D339 -- ○ ○ ✓ ✓ ✓ ✓ MDS D400 -- -- ✓ ✓ ✓ ✓ ✓ MDS D421 ✓ ○ -- -- -- -- ✓ 6) MDS D422 ✓ ✓ ✓ -- -- -- ✓ 6) MDS D423 ✓ ✓ ✓ ✓ ✓ -- ✓ MDS D424 ✓ ✓ ✓ ✓ ✓ ✓ ✓ MDS D425 ✓ ✓ ✓ -- ✓ -- ✓ MDS D426 -- ✓ ✓ ✓ ✓ ✓ ✓ MDS D428 ✓ ✓ ✓ ✓ ✓ -- MDS D460 ✓ ✓ ✓ ✓ ✓ MDS D521 ✓ ○ -- -- -- -- ✓ 6) MDS D522 3) ✓ ✓ ✓ -- -- -- ✓ 6) MDS D524 ✓ ✓ ✓ ✓ ✓ ✓ ✓ MDS D525 ✓ ✓ ✓ -- ✓ -- -- MDS D526 -- ✓ ✓ ✓ ✓ ✓ ✓ MDS D528 ✓ ✓ ✓ ✓ ✓ -- ✓ ○/✓ ✓ 5) 1) only with the article number 6GT2600-0AA10 2) only with the article number 6GT2600-0AB10 3) The transponder MDS D522 special variant has the same compatibility as the transponder MDS D522. 4) in conjunction with ANT D5, D6 or D10 5) combination recommended only in conjunction with ANT D5. 6) Only in conjunction with RF350M for external antennas (6GT2803-1BA10) ✓ Combination possible -- Combination not possible ○ Combination possible, but not recommended ✓ SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 21 System overview 3.1 RFID components and their function Table 3- 2 Reader-transponder combination options, Part 2 RF250R with Transponder ANT 1 ANT 3 ANT 8 ANT 12 ANT 18 ANT 30 MDS D100 ✓ ○ -- -- -- ○ MDS D117 -- -- ✓ ✓ -- -- MDS D124 ✓ ✓ -- -- ✓ ✓ MDS D126 ✓ ✓ -- -- -- ✓ MDS D127 -- -- ✓ ✓ -- -- MDS D139 ✓ ○ -- -- -- ○ MDS D160 ✓ ✓ -- ✓ ✓ ✓ MDS D165 ✓ ○ -- -- -- ○ MDS D200 ✓ ○ -- -- -- ○ MDS D261 ✓ ○ -- -- -- ○ MDS D324 ✓ ✓ -- ○ ✓ ✓ MDS D339 ✓ ○ -- -- -- ○ MDS D400 ✓ ○ -- -- -- ○ MDS D421 -- -- ✓ ✓ ✓ -- MDS D422 -- ✓ -- ✓ ✓ ✓ MDS D423 ✓ ✓ -- -- ✓ ✓ MDS D424 ✓ ✓ -- -- ✓ ✓ MDS D425 ✓ ✓ -- ✓ ✓ ✓ MDS D426 ✓ ✓ -- -- -- ✓ MDS D428 ✓ ✓ -- ✓ ✓ ✓ MDS D460 ✓ ✓ -- ✓ ✓ ✓ MDS D521 -- -- ✓ ✓ ✓ -- D522) -- ✓ -- ✓ ✓ ✓ MDS D524 ✓ ✓ -- -- ✓ ✓ MDS D525 ✓ ✓ -- ✓ ✓ ✓ MDS D526 ✓ ✓ -- -- -- ✓ MDS D528 ✓ ✓ -- ✓ ✓ ✓ MDS ✓ Combination possible -- Combination not possible ○ Combination possible, but not recommended SIMATIC RF200 22 System Manual, 07/2017, J31069-D0227-U001-A9-7619 System overview 3.2 Overview of transponders 3.2 Overview of transponders Overview of typical areas of application of ISO transponders for RF200 Transponder Area of application MDS D100 From simple identification such as electronic barcode replacement or supplementation, through warehouse and distribution logistics, right up to product identification. With this transponder, the maximum ranges are achieved in combination with the SIMATIC RF260R reader. MDS D117 Very compact data carrier that can be cemented into objects where precise positioning is necessary. e.g. tool identification. MDS D124 Application areas in factory automation (e.g. small paintshops to 180°C). MDS D126 Compact and rugged ISO transponder; suitable for identification of transport units in production-related logistics; can also be deployed in harsh conditions. MDS D127 Very compact data carrier that can be screwed into areas where precise positioning is necessary. e.g. tool identification. MDS D139 1) Applications in production automation with high temperature demands (up to +220 °C). Typical application areas: • MDS D160 2) • Primer coat, electrolytic dip area, cataphoresis with the associated drying furnaces • Top coat area with drying furnaces • Washing areas at temperatures > 85 °C • Other applications with higher temperatures Typical applications are, for example: • MDS D165 Paintshops and their preparatory treatments Rented work clothing • Hotel laundry • Surgical textiles • Hospital clothing • Dirt collection mats • Clothing for nursing homes/hostels • Assembly lines with very small workpiece holders Smart label (self-adhesive label) From simple identification such as electronic barcode replacement/supplementation, through warehouse and distribution logistics, right up to product identification MDS D200 From simple identification such as electronic barcode replacement/supplementation, through warehouse and distribution logistics, right up to product identification. MDS D261 Smart label (self-adhesive label) The design of the transponder (self-adhesive label) permits a variety of designs in order to ensure optimum dimensioning for the widest variety of applications. From simple identification such as electronic barcode replacement/supplementation, through warehouse and distribution logistics, right up to product identification. MDS D324 Production and distribution logistics as well as in assembly and production lines MDS D339 Applications in production automation with high temperature demands (up to +220 °C). For typical areas of application, see "MDS D139". SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 23 System overview 3.2 Overview of transponders Transponder Area of application MDS D400 Simple identification such as electronic barcode replacement/supplements, from warehouse and distribution logistics right through to product identification. MDS D421 The MDS D421 is designed for tool coding according to DIN 69873. It can be used wherever small data carriers and exact positioning are required, e.g. tool identification, workpiece holders MDS D422 Identification of metallic workpiece holders, workpieces or containers MDS D423 Identification of metallic workpiece holders, workpieces or containers, production automation MDS D424 Production and distribution logistics as well as in assembly and production lines MDS D425 Compact and rugged ISO transponder; suitable for screw mounting. Use in assembly and production lines in the powertrain sector; ideal for mounting on motors, gearboxes, and workpiece holders MDS D426 Compact and rugged ISO transponder; suitable for identification of transport units in production-related logistics; can also be deployed in harsh conditions MDS D428 Compact and rugged ISO transponder; suitable for screw mounting Use in assembly and production lines in the powertrain sector MDS D460 Assembly lines with very small workpiece holders MDS D521 The MDS D521 is constructed for tool coding according to DIN 69873. It can be used wherever small data carriers and exact positioning are required, e.g. tool identification, workpiece holders. MDS D522 Identification of metallic workpiece holders, workpieces or containers MDS D522 Special variants If Identification of metallic workpiece holders or workpieces MDS D524 Production and distribution logistics as well as in assembly and production lines MDS D526 Compact and rugged ISO transponder; suitable for identification of transport units in production-related logistics; can also be deployed in harsh environmental conditions MDS D528 Compact and rugged ISO transponder; suitable for screw mounting Use in assembly and production lines in the powertrain sector 1) Only with the MLFB 6GT2600-0AA10 2) Only with the MLFB 6GT2600-0AB10 Overview of the memory sizes of the ISO transponders for RF200 Transponder Memory size MDS D1xx 112 bytes of EEPROM MDS D2xx 256 bytes of EEPROM MDS D3xx 992 bytes of EEPROM MDS D4xx 2000 bytes FRAM MDS D5xx 8192 bytes FRAM SIMATIC RF200 24 System Manual, 07/2017, J31069-D0227-U001-A9-7619 System overview 3.2 Overview of transponders SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 25 Planning the RF200 system 4.1 Fundamentals of application planning 4.1.1 Selection criteria for SIMATIC RF200 components Assess your application according to the following criteria, in order to choose the right SIMATIC RF200 components: ● Static or dynamic data transfer ● Data volume to be transferred ● Speed in case of dynamic transfer ● Ambient conditions such as relative humidity, temperature, chemical impacts, etc. 4.1.2 Transmission window and read/write distance The reader generates an inductive alternating field. The field is strongest close to the reader; however, a read/write distance of "zero" between reader and transponder is not recommended. The field strength of the alternating field decreases quickly in proportion to the distance from the reader. The distribution of the field depends on the structure and geometry of the antennas in the reader and transponder A prerequisite for the function of the transponder is a minimum field strength at the transponder, which is still barely achieved at distance Sg from the reader. The picture below shows the transmission window of the SIMATIC RF210R and SIMATIC RF220R readers between transponder and reader: SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 27 Planning the RF200 system 4.1 Fundamentals of application planning Sa Operating distance between transponder and reader Sg Limit distance (maximum clear distance between upper surface of the reader and the transponder, at which the transmission can still function under normal conditions) Diameter of a transmission window SP Intersection of the axes of symmetry of the transponder Figure 4-1 RF210R/RF220R transmission window The figure below shows the transmission window of the SIMATIC RF240R and SIMATIC RF260R readers between transponder and reader: SIMATIC RF200 28 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.1 Fundamentals of application planning Sa Operating distance between transponder and reader Sg Limit distance (maximum clear distance between upper surface of the reader and the transponder, at which the transmission can still function under normal conditions) Length of a transmission window Field centerpoint Figure 4-2 RF240R/RF260R transmission window The transponder can be used as soon as the intersection (SP) of the transponder enters the area of the transmission window. From the diagrams above, it can also be seen that operation is possible within the area between Sa and Sg. The active operating area reduces as the distance increases, and shrinks to a single point at distance Sg. Only static mode should thus be used in the area between Sa and Sg. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 29 Planning the RF200 system 4.1 Fundamentals of application planning 4.1.3 Width of the transmission window Determining the width of the transmission window The following approximation formula can be used for practical applications: B: Width of the transmission window L: Length of the transmission window Tracking tolerances The width of the transmission window (B) is particularly important for the mechanical tracking tolerance. The formula for the dwell time is valid without restriction when B is observed. SIMATIC RF200 30 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.1 Fundamentals of application planning 4.1.4 Impact of secondary fields Secondary fields in the range from 0 mm to 30% of the limit distance (Sg) generally always exist. They should, however, only be used during configuration in exceptional cases, since the read/write distances are very limited. Exact details of the secondary field geometry cannot be given, since these values depend heavily on the operating distance and the application. When working in dynamic mode, remember that during the transition from the secondary field to the main field the presence of the tag is lost temporarily. It is therefore advisable to select a distance > 30 % of Sg. ① ② Main field Secondary field Figure 4-3 Gap in the field resulting from secondary fields SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 31 Planning the RF200 system 4.1 Fundamentals of application planning Secondary fields without shielding The following graphic shows typical primary and secondary fields, if no shielding measures are taken. ① ② Main field Secondary field Figure 4-4 Secondary field without shielding In this arrangement, the reader can also read tags via the secondary field. Shielding is required in order to prevent unwanted reading via the secondary field, as shown and described in the following. SIMATIC RF200 32 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.1 Fundamentals of application planning Secondary fields with shielding The following graphic shows typical primary and secondary fields, with metal shielding this time. The metal shielding prevents the reader from detecting tags via the secondary field. ① ② Main field Secondary field Figure 4-5 Secondary field with shielding SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 33 Planning the RF200 system 4.1 Fundamentals of application planning 4.1.5 Permissible directions of motion of the transponder Detection area and direction of motion of the transponder The transponder and reader have no polarization axis, i.e. the transponder can come in from any direction, assume any position as parallel as possible to the reader, and cross the transmission window. The figure below shows the active area for various directions of transponder motion: Transmission window Direction of motion of the transponder Detection area L x W Figure 4-6 Detection areas of the reader for different directions of transponder motion SIMATIC RF200 34 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.1 Fundamentals of application planning 4.1.6 Operation in static and dynamic mode Operation in static mode If working in static mode, the transponder can be operated up to the limit distance (Sg). The transponder must then be positioned exactly over the reader: Figure 4-7 Operation in static mode Note Note that in a metallic environment the values for the limit distance are reduced. Operation in dynamic mode When working in dynamic mode, the transponder moves past the reader. The transponder can be used as soon as the intersection (SP) of the transponder enters the circle of the transmission window. In dynamic mode, the operating distance (Sa) is of primary importance. [Operating distances, see Chapter Field data of transponders and readers (Page 38)] Figure 4-8 Operation in dynamic mode SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 35 Planning the RF200 system 4.1 Fundamentals of application planning 4.1.7 Dwell time of the transponder The dwell time is the time in which the transponder remains within the transmission window of the reader. The reader can exchange data with the transponder during this time. The dwell time is calculated as follows: tV: Dwell time of the transponder L: Length of the transmission window vTag: Speed of the transponder (tag) in dynamic mode 0.8: Constant factor used to compensate for temperature influence and production tolerances The dwell time can be of any duration in static mode. The dwell time must be sufficiently long to allow communication with the transponder. The dwell time is defined by the system environment in dynamic mode. The volume of data to be transferred must be matched to the dwell time or vice versa. As a general rule: tV:: Dwell time of the data memory in the field of the reader tK: Communication time between transponder and communication module or Calculation of the maximum amount of user data tK: Communication time between transponder and communication module Constant; the constant is an internal system time. This includes the time for power buildup on the MDS and for command transfer tByte Transmission time for 1 byte Amount of user data in bytes nmax Maximum amount of user data in bytes in dynamic mode tV Dwell time of the data memory in the field of the reader SIMATIC RF200 36 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.1 Fundamentals of application planning 4.1.8 Communication between communication module, reader and transponder Aids for calculating the data transmission times User-friendly calculation tools are available for the communications modules ASM 456, RF160C, RF170C and RF180C to calculate data transfer times. The calculation tools can be found on the DVD "Ident Systems Software & Documentation", article number 6GT20802AA20. Figure 4-9 User interface of the calculation tool for command processing time SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 37 Planning the RF200 system 4.2 Field data of transponders and readers Aids for calculating the field data You will also find a tool for calculating field data on the DVD "Ident Systems, Software & Documentation". Using this tool, among other things you can calculate the operating distance (Sa), limit distance (Sg) and transmission window (L). Figure 4-10 4.2 User interface of the calculation tool for field data acquisition Field data of transponders and readers The following tables show the field data for all SIMATIC RF200 components of transponders and readers. This makes the correct selection of a transponder and reader particularly easy. All the technical specifications listed are typical data and are applicable for an ambient temperature between 0 °C and +50 °C, a supply voltage between 22 and 27 VDC and a metal-free environment. Tolerances of ±20 % are permitted due to production or temperature conditions. If the entire voltage range at the reader of 20 VDC to 30 VDC and/or the entire temperature range of transponders and readers is used, the field data is subject to further tolerances. Note Transmission gaps If the minimum operating distance (Sa) is not observed, a transmission gap can occur in the center of the field. Communication with the transponder is not possible in the transmission gap. SIMATIC RF200 38 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.2 Field data of transponders and readers Note Possible reader-transponder combinations The tables of the following section show the possible reader-transponder combinations. 4.2.1 Field data The limit distances (Sg) and operating distances (Sa) along with the length of the transmission window for each reader-transponder combination are listed in the tables below. Table 4- 1 SIMATIC RF210R field data Length of the transmission window (Ld) Operating distance (Sa) Limit distance (Sg) 25 1 ... 18 20 MDS D124 MDS D127 0 ... 2 MDS D160 20 1 ... 10 12 MDS D324 20 1 ... 8 MDS D421 0 ... 3 MDS D422 1 ... 9 10 MDS D423 20 2 ... 10 12 MDS D424 24 1 ... 16 18 MDS D425 12 1 ... 6 MDS D428 20 1 ... 10 11 MDS D460 1…8 MDS D521 0 ... 3 MDS D522 1 ... 8 MDS D522 Special variants 1 ... 8 MDS D524 20 1 ... 15 17 MDS D525 12 1 ... 6 MDS D528 15 1 ... 10 11 1) 1) The transponder is only suitable for static mode. All dimensions in mm. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 39 Planning the RF200 system 4.2 Field data of transponders and readers Table 4- 2 SIMATIC RF220R field data Length of the transmission window (Ld) Operating distance (Sa) Limit distance (Sg) MDS D124 35 1 ... 28 31 MDS D126 45 2 ... 30 35 MDS D160 20 1 ... 20 22 MDS D324 30 2 ... 21 25 MDS D422 18 1 ... 12 14 MDS D423 30 2 ...24 28 MDS D424 30 2 ... 25 29 MDS D425 20 1 ... 11 13 MDS D426 40 2 ... 25 30 MDS D428 25 1 ... 18 21 MDS D460 25 1 ... 18 20 MDS D522 15 1 ... 10 12 MDS D522 Special variants 15 1 ... 10 12 MDS D524 25 2 ... 22 25 MDS D525 20 1 ... 11 13 MDS D526 30 2 ... 25 30 MDS D528 20 1 ... 15 20 Length of the transmission window (L) Operating distance (Sa) Limit distance (Sg) MDS D100 100 2 ... 84 95 MDS D124 65 2 ... 53 60 MDS D126 80 2 ... 57 65 MDS D160 50 1 ... 33 37 MDS D165 105 2 ... 80 94 MDS D200 90 2 ... 69 78 MDS D261 70 2 ... 60 70 MDS D324 55 1 ... 36 40 MDS D400 95 2 ... 80 90 MDS D422 25 1 ... 12 15 MDS D423 45 2 ... 35 40 MDS D424 75 1 ... 47 53 MDS D425 30 1 ... 15 17 MDS D426 65 2 ... 45 55 MDS D428 50 1 ... 30 34 MDS D460 50 1 ... 30 34 All dimensions in mm. Table 4- 3 SIMATIC RF240R field data SIMATIC RF200 40 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.2 Field data of transponders and readers Length of the transmission window (L) Operating distance (Sa) Limit distance (Sg) MDS D522 20 1 ... 10 12 MDS D522 Special variants 20 1 ... 10 12 MDS D524 60 1 ... 45 55 MDS D525 30 1 ... 15 17 MDS D526 60 2 ... 45 55 MDS D528 40 1 ... 30 35 Length of the transmission window (Ld) Operating distance (Sa) Limit distance (Sg) MDS D100 80 5 ... 95 115 MDS D124 55 2 ... 60 75 MDS D126 150 2 ... 80 95 MDS D139 75 5 ... 90 105 MDS D160 50 2 ... 35 45 MDS D165 140 5 ... 95 110 MDS D200 130 5 ... 90 100 MDS D261 100 2 ... 90 110 MDS D324 50 5 ... 60 70 MDS D339 110 2 ... 85 100 MDS D400 140 10 ... 95 110 MDS D423 50 2 ... 35 45 MDS D424 40 2 ... 70 80 MDS D425 40 2 ... 25 30 MDS D426 110 2 ... 80 95 MDS D428 40 2 ... 40 50 MDS D460 50 2 ... 30 40 MDS D524 50 2 ... 65 80 MDS D525 40 2 ... 25 30 MDS D526 110 2 ... 80 95 MDS D528 40 2 ... 40 45 All dimensions in mm. Table 4- 4 Field data SIMATIC RF250R, with ANT 1 All dimensions in mm. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 41 Planning the RF200 system 4.2 Field data of transponders and readers Table 4- 5 Field data SIMATIC RF250R, with ANT 3 Length of the transmission window (Ld) Operating distance (Sa) Limit distance (Sg) MDS D124 40 1 ... 32 40 MDS D126 65 0 ... 47 60 MDS D160 24 1 ... 23 30 MDS D324 32 1 ... 22 35 MDS D422 20 0 ... 12 15 MDS D423 30 2 ... 18 26 MDS D424 37 0 ... 34 48 MDS D425 22 1 ... 12 20 MDS D426 65 0 ... 44 58 MDS D428 30 1 ... 20 32 MDS D460 24 1 ... 21 27 MDS D522 20 1 ... 12 15 MDS D522 Special variants 20 1 ... 12 15 MDS D524 35 1 ... 35 40 MDS D525 22 1 ... 12 20 MDS D526 45 2 ... 35 45 MDS D528 25 1 ... 20 25 Length of the transmission window (Ld) Operating distance (Sa) Limit distance (Sg) MDS D117 0 ... 2 MDS D127 0 ... 3 MDS D421 0 ... 3 MDS D521 0 ... 3 All dimensions in mm. Table 4- 6 Field data SIMATIC RF250R, with ANT 8 All dimensions in mm. SIMATIC RF200 42 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.2 Field data of transponders and readers Table 4- 7 Field data SIMATIC RF250R, with ANT 12 Length of the transmission window (Ld) Operating distance (Sa) Limit distance (Sg) MDS D117 0 ... 3 MDS D127 0 ... 4 MDS D160 18 0 ... 12 17 MDS D421 10 0 ... 3 MDS D422 22 0 ... 7 10 MDS D425 12 0 ... 8 10 MDS D428 18 1 ... 8 12 MDS D460 16 1 ... 10 14 MDS D521 0 ... 3 MDS D522 10 1 ... 7 MDS D522 Special variants 10 1 ... 7 MDS D525 12 1 ... 8 10 MDS D528 15 1 ... 8 12 Length of the transmission window (Ld) Operating distance (Sa) Limit distance (Sg) MDS D124 26 0 ... 24 37 MDS D160 22 1 ... 18 26 MDS D324 30 1 ... 18 27 MDS D421 16 0 ... 3 MDS D422 24 1 ... 8 14 MDS D423 21 1 ... 15 18 MDS D424 26 1 ... 27 36 MDS D425 19 1 ... 11 16 MDS D428 19 1 ... 18 25 MDS D460 19 1 ... 17 21 MDS D521 0 ... 4 MDS D522 15 1 ... 10 12 MDS D522 Special variants 15 1 ... 10 12 MDS D524 30 1 ... 25 30 MDS D525 19 1 ... 11 16 MDS D528 20 1 ... 15 20 All dimensions in mm. Table 4- 8 Field data SIMATIC RF250R, with ANT 18 All dimensions in mm. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 43 Planning the RF200 system 4.2 Field data of transponders and readers Table 4- 9 Field data SIMATIC RF250R, with ANT 30 Length of the transmission window (Ld) Operating distance (Sa) Limit distance (Sg) MDS D124 40 1 ... 35 48 MDS D126 65 0 ... 47 60 MDS D160 24 1 ... 23 30 MDS D324 32 1 ... 22 35 MDS D422 27 0 ... 12 15 MDS D423 30 2 ... 18 26 MDS D424 37 0 ... 34 48 MDS D425 22 1 ... 12 20 MDS D426 65 0 ... 44 58 MDS D428 30 1 ... 20 32 MDS D460 24 1 ... 21 27 MDS D522 20 1 ... 12 15 MDS D522 Special variants 20 1 ... 12 15 MDS D524 35 1 ... 35 40 MDS D525 22 1 ... 12 20 MDS D526 60 2 ... 35 45 MDS D528 25 1 ... 20 25 Length of the transmission window (L) Operating distance (Sa) Limit distance (Sg) 120 2 ... 110 130 All dimensions in mm. Table 4- 10 MDS D100 SIMATIC RF260R field data MDS D124 80 2 ... 80 85 MDS D126 110 2 ... 75 100 MDS D139 120 2 ... 80 110 MDS D160 60 2 ... 40 45 MDS D165 120 2 ... 120 135 MDS D200 120 2 ... 100 120 MDS D261 80 2 ... 75 90 MDS D324 80 2 ... 60 70 MDS D339 110 5 ... 65 80 MDS D400 140 2 ... 110 140 MDS D423 55 2 ... 40 45 MDS D424 80 2 ... 60 70 MDS D426 75 2 ... 70 85 MDS D428 50 2 ... 40 45 MDS D460 50 2 ... 40 45 SIMATIC RF200 44 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.2 Field data of transponders and readers Length of the transmission window (L) Operating distance (Sa) Limit distance (Sg) MDS D524 70 2 ... 60 70 MDS D526 80 2 ... 70 85 MDS D528 50 2 ... 35 40 All dimensions in mm. Table 4- 11 Field data SIMATIC RF280R Length of the transmission window (L) Operating distance (Sa) Limit distance (Sg) in the x direction (Lx) in the y direction (Ly) 140 100 10 ... 160 200 MDS D100 1) MDS D124 80 80 2 ... 110 130 MDS D126 180 140 2 ... 135 160 MDS D139 140 90 5 ... 115 190 MDS D160 80 40 2 ... 55 70 MDS D165 1) 200 140 10 ... 160 190 MDS D200 2) 200 160 20 ... 140 185 MDS D261 3) 190 120 20 ... 110 150 MDS D324 100 60 2 ... 85 110 MDS D339 290 140 5 ... 115 170 MDS D400 240 120 10 ... 170 200 MDS D423 110 60 5 ... 60 70 MDS D424 100 70 2 ... 100 140 MDS D425 80 45 2 ... 30 40 MDS D426 220 160 2 ... 145 175 MDS D428 80 50 2 ... 60 88 MDS D460 80 70 2 ... 55 70 MDS D524 100 70 2 ... 110 130 MDS D525 80 45 2 ... 30 40 MDS D526 220 160 2 ... 135 165 MDS D528 80 50 2 ... 60 85 All dimensions in mm. 1) Be aware that the minimum distance must be increased 10 mm starting at 40 °C ambient temperature. 2) Be aware that the minimum distance of the reader to the transponder must be increased approximately 6 mm every 5 °C starting at an ambient temperature of 25 °C and approximately 15 mm starting at an ambient temperature of 50 °C. 3) Be aware that the minimum distance of the reader to the transponder must be increased approximately 3 mm every 5 °C starting at an ambient temperature of 25 °C and approximately 14 mm starting at an ambient temperature of 50 °C. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 45 Planning the RF200 system 4.2 Field data of transponders and readers Table 4- 12 Field data SIMATIC RF290R, with ANT D5 (at 4 W) Length of the transmission window (L) Operating distance (Sa) Limit distance (Sg) MDS D100 320 0 ... 400 500 MDS D124 300 0 ... 200 280 MDS D126 320 0 ... 350 400 MDS D139 320 0 ... 400 500 MDS D160 300 0 ... 130 180 MDS D165 320 0 ... 350 450 MDS D200 320 0 ... 400 500 MDS D261 320 0 ... 300 400 MDS D324 300 0 ... 200 280 MDS D339 320 0 ... 300 380 MDS D400 320 0 ... 400 500 MDS D424 300 0 ... 200 280 MDS D426 320 0 ... 300 350 MDS D460 300 0 ... 120 160 MDS D524 300 0 ... 200 280 MDS D526 320 0 ... 300 350 All dimensions in mm. Table 4- 13 Field data SIMATIC RF290R, with ANT D6 (at 4 W) Length of the transmission window (L) Operating distance (Sa) Limit distance (Sg) X direction Y direction MDS D100 520 420 0 ... 550 650 MDS D124 500 400 0 ... 220 300 MDS D126 520 420 0 ... 400 500 MDS D139 520 420 0 ... 500 600 MDS D160 500 400 0 ... 130 180 MDS D165 520 420 0 ... 400 500 MDS D200 520 420 0 ... 500 600 MDS D261 520 420 0 ... 350 450 MDS D324 500 400 0 ... 200 280 MDS D339 520 420 0 ... 400 480 MDS D400 520 420 0 ... 500 650 MDS D424 500 400 0 ... 220 300 MDS D426 520 420 0 ... 350 400 MDS D524 500 400 0 ... 220 300 MDS D526 520 420 0 ... 350 400 All dimensions in mm. SIMATIC RF200 46 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.2 Field data of transponders and readers Table 4- 14 Field data SIMATIC RF290R, with ANT D10 (at 4 W) Length of the transmission window (L) Operating distance (Sa) Limit distance (Sg) X direction Y direction MDS D100 1050 350 0 ... 500 600 MDS D124 1000 300 0 ... 200 280 MDS D126 1050 350 0 ... 400 500 MDS D139 1050 350 0 ... 450 550 MDS D160 1000 300 0 ... 130 180 MDS D165 1050 350 0 ... 350 450 MDS D200 1050 350 0 ... 450 550 MDS D261 1050 350 0 ... 350 450 MDS D324 1000 300 0 ... 200 280 MDS D339 1050 350 0 ... 300 380 MDS D400 1050 350 0 ... 400 500 MDS D424 1000 300 0 ... 200 280 MDS D426 1050 350 0 ... 350 400 MDS D524 1000 300 0 ... 220 300 MDS D526 1050 350 0 ... 350 400 All dimensions in mm. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 47 Planning the RF200 system 4.2 Field data of transponders and readers 4.2.2 Minimum clearances Minimum distance from transponder to transponder The specified distances refer to a metal-free environment. For a metallic environment, the specified minimum distances must be multiplied by a factor of 1.5. The transponders designed specifically for installation in/on metal are an exception to this. Table 4- 15 Minimum clearances for transponders RF210R RF220R RF240R RF260R RF280R MDS D100 -- -- -- ≥ 240 ≥ 420 MDS D117 ≥ 15 -- -- -- -- MDS D124 ≥ 25 ≥ 40 ≥ 90 ≥ 180 ≥ 360 MDS D126 -- ≥ 50 ≥ 100 ≥ 180 ≥ 400 MDS D127 ≥ 15 -- -- -- -- MDS D139 -- -- -- ≥ 200 ≥ 450 MDS D160 ≥ 20 ≥ 25 ≥ 70 ≥ 150 ≥ 300 MDS D165 -- -- -- ≥ 240 ≥ 500 MDS D200 -- -- -- ≥ 240 ≥ 500 MDS D261 -- -- -- ≥ 200 ≥ 400 MDS D324 ≥ 25 ≥ 40 ≥ 90 ≥ 180 ≥ 360 MDS D339 -- -- -- ≥ 200 ≥ 450 MDS D400 -- -- -- ≥ 240 ≥ 500 MDS D421 ≥ 10 -- -- -- -- MDS D422 ≥ 15 ≥ 20 ≥ 50 -- -- MDS D423 -- -- ≥ 80 ≥ 160 ≥ 250 MDS D424 ≥ 25 ≥ 40 ≥ 90 ≥ 180 ≥ 360 MDS D425 ≥ 20 ≥ 25 ≥ 75 -- ≥ 250 MDS D426 -- ≥ 50 ≥ 90 ≥ 180 ≥ 400 MDS D428 ≥ 25 ≥ 25 ≥ 75 ≥ 150 ≥ 300 MDS D460 ≥ 20 ≥ 25 ≥ 70 ≥ 150 ≥ 300 MDS D521 ≥ 10 -- -- -- -- MDS D522 ≥ 15 ≥ 20 ≥ 50 -- -- MDS D522 Special variants ≥ 15 ≥ 20 ≥ 50 -- -- MDS D524 ≥ 25 ≥ 40 ≥ 90 ≥ 180 ≥ 360 MDS D526 -- ≥ 50 ≥ 90 ≥ 180 ≥ 400 MDS D528 ≥ 25 ≥ 25 ≥ 75 ≥ 150 ≥ 300 All values are in mm, relative to the operating distance (Sa) between reader and transponder, and between transponder edge and transponder edge SIMATIC RF200 48 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.2 Field data of transponders and readers Table 4- 16 Minimum clearances for transponders RF250R 1) RF290R 2) ANT 3 ANT 8 ANT 12 ANT 18 ANT 30 ANT D5 ANT D6 ANT D10 MDS D100 -- -- -- -- -- ≥ 1000 ≥ 1500 ≥ 2000 MDS D117 -- ≥ 30 ≥ 50 -- -- -- -- -- MDS D124 ≥ 100 -- -- ≥ 80 ≥ 100 ≥ 800 ≥ 1200 ≥ 1800 MDS D126 ≥ 100 -- -- -- ≥ 100 ≥ 1000 ≥ 1500 ≥ 2000 MDS D127 -- ≥ 40 ≥ 60 -- -- -- -- -- MDS D139 -- -- -- -- -- ≥ 1000 ≥ 1500 ≥ 2000 MDS D160 ≥ 100 -- ≥ 60 ≥ 80 ≥ 100 ≥ 800 ≥ 1200 ≥ 1800 MDS D165 -- -- -- -- -- ≥ 1000 ≥ 1500 ≥ 2000 MDS D200 -- -- -- -- -- ≥ 1000 ≥ 1500 ≥ 2000 MDS D261 -- -- -- -- -- ≥ 1000 ≥ 1500 ≥ 2000 MDS D324 ≥ 100 -- -- ≥ 80 ≥ 100 ≥ 800 ≥ 1200 ≥ 1800 MDS D339 -- -- -- -- -- ≥ 1000 ≥ 1500 ≥ 2000 MDS D400 -- -- -- -- -- ≥ 1000 ≥ 1500 ≥ 2000 MDS D421 -- ≥ 30 ≥ 40 ≥ 50 -- -- -- -- MDS D422 ≥ 70 -- ≥ 50 ≥ 60 ≥ 70 -- -- -- MDS D423 ≥ 100 -- -- ≥ 80 ≥ 100 -- -- -- MDS D424 ≥ 100 -- -- ≥ 80 ≥ 100 ≥ 800 ≥ 1200 ≥ 1800 MDS D425 ≥ 80 -- ≥ 50 ≥ 60 ≥ 80 -- -- -- MDS D426 ≥ 100 -- -- -- ≥ 100 ≥ 800 ≥ 1200 ≥ 1800 MDS D428 ≥ 80 -- ≥ 50 ≥ 60 ≥ 80 -- -- -- MDS D460 ≥ 100 -- ≥ 60 ≥ 80 ≥ 100 ≥ 800 -- -- MDS D521 -- ≥ 30 ≥ 40 ≥ 50 -- -- -- -- MDS D522 ≥ 70 -- ≥ 50 ≥ 60 ≥ 70 -- -- -- MDS D522 Special variants ≥ 70 -- ≥ 50 ≥ 60 ≥ 70 -- -- -- MDS D524 ≥ 100 -- -- ≥ 80 ≥ 100 ≥ 800 ≥ 1200 ≥ 1800 MDS D526 ≥ 100 -- -- -- ≥ 100 ≥ 800 ≥ 1200 ≥ 1800 MDS D528 ≥ 80 -- ≥ 50 ≥ 60 ≥ 80 -- -- -- 1) Depends on the connected antenna (ANT 3, 8, 12, 18 or 30). 2) Depends on the connected antenna (ANT D5, D6 or D10). All values are in mm, relative to the operating distance (Sa) between reader and transponder, and between transponder edge and transponder edge SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 49 Planning the RF200 system 4.3 Installation guidelines Minimum distance from reader to reader Table 4- 17 Minimum distances to readers or antennas RF210R to RF210R RF220R to RF220R RF240R to RF240R ANT x to ANT x with RF250R ≥ 60 ≥ 100 ≥ 120 ANT 3: ≥ 100 RF260R to RF280R to RF260R RF280R ≥ 150 ANT 8: ≥ 50 ANT 12: ≥ 60 ANT 18: ≥ 80 ANT 30: ≥ 100 with 2 readers ≥ 400 with multiple readers ≥ 500 ANT Dx to ANT Dx with RF290R ANT D5: ≥ 2000 ANT D10: ≥ 2000 All values are in mm Note Effect on inductive fields by not maintaining the minimum distances of the readers If the values fall below those specified in the "minimum distance readers or antennas", there is a risk of the function being affected by inductive fields. In this case, the data transfer time would increase unpredictably or a command would be aborted with an error. Keeping to the values specified in the "Minimum distance readers or antennas" table is therefore essential. If the specified minimum distance cannot be complied with due to the physical configuration, the SET-ANT command can be used to activate and deactivate the HF field of the reader. The application software must be used to ensure that only one reader is active (antenna is switched on) at a time. 4.3 Installation guidelines 4.3.1 Overview The transponder and reader complete with their antennas are inductive devices. Any type of metal in the vicinity of these devices affects their functionality. Some points need to be considered during planning and installation if the values described in the "Field data (Page 39)" section are to retain their validity: ● Minimum spacing between two readers or their antennas ● Minimum distance between two adjacent data memories ● Metal-free area for flush-mounting of readers or their antennas and transponders in metal ● Mounting of multiple readers or their antennas on metal frames or racks SIMATIC RF200 50 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines The following sections describe the impact on the operation of the RFID system when mounted in the vicinity of metal. 4.3.2 Table 4- 18 Reduction of interference due to metal Interference due to metal rack Representation Description Problem: A metal rack is located above the transmission window of the reader. This affects the entire field. In particular, the transmission window between reader and transponder is reduced. Remedy: The transmission window is no longer affected if the transponder is mounted differently. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 51 Planning the RF200 system 4.3 Installation guidelines Table 4- 19 Flush-mounting of transponders and readers Representation Description Problem: Flush-mounting of transponders and readers is possible in principle. However, the size of the transmission window is significantly reduced. The following measures can be used to counteract the reduction of the window: Remedy: Enlargement of the non-metallic spacer below the transponder and/or reader. The transponder and/or reader are 10 to 20 mm higher than the metal surround. (The value x ≥ 100 mm is valid, for example, for RF260R. It indicates that, for a distance x ≥ 100 mm, the reader can no longer be significantly affected by metal.) Remedy: Increase the distances a, b to metal. The following rule of thumb can be used: • Increase a, b by a factor of 2 to 3 over the values specified for metal-free areas • Increasing a, b has a greater effect for readers or transponders with a large limit distance than for readers or transponders with a small limit distance. SIMATIC RF200 52 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Mounting of several readers on metal frames or racks Any reader mounted on metal couples part of the field to the metal frame. There is normally no interaction as long as the minimum distance D and metal-free areas a, b are maintained. However, interaction may take place if an iron frame is positioned unfavorably. Longer data transfer times or sporadic error messages at the communication module are the result. Table 4- 20 Mounting of several readers on metal frames or racks Representation Description Problem: Interaction between readers Remedy: Increase the distance D between the two readers. Remedy: Introduce one or more iron struts in order to shortcircuit the stray fields. Remedy: Insert a non-metallic spacer of 20 to 40 millimeter thickness between the reader and the iron frame. This will significantly reduce the induction of stray fields on the rack: 4.3.3 Effects of metal on different transponders and readers Mounting different transponders and readers on metal or flush-mounting Certain conditions have to be observed when mounting the transponders and readers on metal or flush-mounting. For more information, please refer to the descriptions of the individual transponders and readers in the relevant section. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 53 Planning the RF200 system 4.3 Installation guidelines 4.3.4 Impact of metal on the transmission window In general, the following points should be considered when mounting RFID components: ● Direct mounting on metal is allowed only in the case of specially approved transponders. ● Flush-mounting of the components in metal reduces the field data; a test is recommended in critical applications. ● When working inside the transmission window, make sure that no metal rail (or similar part) intersects the transmission field. The metal rail would affect the field data. ● With readers with a large antenna surface (e.g. RF340R) for reasons of communication reliability, when the transponders are flush-mounted in metal, a metal-free space around the transponders is recommended. This metal-free space should match the size of the antenna surface. ● The reduction of field data is also based on the minimum distance between the reader and transponder. The respective recommendations are listed in the following table. The impact of metal on the field data (Sg, Sa, L) is shown in a table in this section. The values in the tables describe field data reduction and show the reduced range as a percentage. The range relates to use in a non-metallic environment. A value of 100% means no influence on the range. Note Possible reader-transponder combinations The tables of the following section show the possible reader-transponder combinations. SIMATIC RF200 54 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines 4.3.4.1 RF210R The RF210R can be flush-mounted in metal. Please allow for a possible reduction in the field data values. To avoid reduction in the case of d), the distance a should be ≥ 10 mm. The following table shows the different arrangements for the reader with and without a metallic environment: Case Diagram Description a) Reader metal-free b) Reader on metal, distance from metal ≥ 12 mm c) Reader in metal, flush against M18 nut d) Reader in metal, all around SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 55 Planning the RF200 system 4.3 Installation guidelines Table 4- 21 Reduction of field data due to metal, range as %: Transponder and RF210R Transponder Reader without direct metal influence Reader flushmounted in metal (Case a, b and d) (Case c) Metal-free 100 82 On metal, distance 15 mm 90 90 Flush-mounted in metal; distance all round 15 mm 85 80 MDS D127 Flush-mounted in metal; distance all round 0 mm 100 75 MDS D160 1) Metal-free 100 95 On metal, distance 10 mm 100 95 Metal-free 100 90 On metal, distance 15 mm 90 90 Flush-mounted in metal; distance all round 25 mm 80 90 Metal-free 100 90 Flush-mounted in metal; distance all round 0 mm 75 50 Metal-free 100 80 Flush-mounted in metal; distance all round 0 mm 90 40 Metal-free 100 90 On metal, distance 0 mm 110 2) 100 2) Flush-mounted in metal; distance all round 10 mm 95 85 Metal-free 100 60 On metal, distance 15 mm 90 80 Flush-mounted in metal; distance all round 25 mm 85 75 Metal-free 100 85 On metal, distance 0 mm 100 85 Metal-free 100 90 On metal, distance 0 mm 100 80 Metal-free 100 90 On metal, distance 25 mm 100 90 Metal-free 100 90 Flush-mounted in metal; distance all round 0 mm 75 50 Metal-free 100 80 Flush-mounted in metal; distance all round 0 mm 90 40 Metal-free 100 80 Flush-mounted in metal; distance all round 0 mm 90 40 MDS D124 1) MDS D324 1) MDS D421 MDS D422 MDS D423 MDS D424 1) MDS D425 MDS D428 MDS D460 1) MDS D521 MDS D522 MDS D522 Special variants SIMATIC RF200 56 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Transponder MDS D524 1) MDS D528 Reader without direct metal influence Reader flushmounted in metal (Case a, b and d) (Case c) Metal-free 100 60 On metal, distance 15 mm 90 80 Flush-mounted in metal; distance all round 25 mm 85 75 Metal-free 100 90 On metal, distance 0 mm 100 80 1) Mounting the transponder on or in metal is only possible with the appropriate spacer or if there is adequate clearance to the metal. 2) Values of > 100 % related to non metal surroundings can occur if transponders were developed specifically for mounting in/on metallic surroundings. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 57 Planning the RF200 system 4.3 Installation guidelines 4.3.4.2 RF220R The RF220R can be flush-mounted in metal. Please allow for a possible reduction in the field data values. To avoid reduction in the case of d), the distance a should be ≥ 15 mm. The following table shows the different arrangements for the reader with and without a metallic environment: Case Diagram Description a) Reader metal-free b) Reader on metal, distance from metal ≥ 12 mm c) Reader in metal, flush against M30 nut d) Reader in metal, all round SIMATIC RF200 58 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Table 4- 22 Reduction of field data due to metal, range as %: Transponder and RF220R Transponder MDS D124 1) MDS D126 1) MDS D160 1) MDS D324 1) MDS D422 MDS D423 MDS D424 1) MDS D425 MDS D426 1) MDS D428 MDS D460 1) MDS D522 Reader without direct metal influence Reader flushmounted in metal (Case a, b and d) (Case c) Metal-free 100 94 On metal, distance 15 mm 97 89 Tag flush-mounted in metal; distance all round 15 mm 86 83 Metal-free 100 75 On metal, distance 25 mm 85 70 Flush-mounted in metal; distance all round 50 mm 80 65 Metal-free 100 89 On metal, distance 10 mm 100 89 Metal-free 100 90 On metal, distance 15 mm 97 86 Flush-mounted in metal; distance all round 25 mm 93 86 Metal-free 100 90 Flush-mounted in metal; distance all round 0 mm 85 85 Metal-free 100 90 On metal, distance 0 mm 125 Flush-mounted in metal; distance all round 10 mm 80 75 Metal-free 100 93 On metal, distance 15 mm 96 89 Flush-mounted in metal; distance all round 25 mm 86 82 Metal-free 100 90 Screwed onto metal 100 75 Flush-mounted in metal; distance all round 25 mm 95 75 Metal-free 100 90 On metal, distance 25 mm 90 75 Flush-mounted in metal; distance all round 50 mm 80 70 Metal-free 100 94 On metal, distance 0 mm 100 94 Metal-free 100 92 On metal, distance 0 mm 100 92 Metal-free 100 90 Flush-mounted in metal; distance all round 0 mm 85 85 2) 115 2) SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 59 Planning the RF200 system 4.3 Installation guidelines Transponder Reader flushmounted in metal (Case a, b and d) (Case c) MDS D522 Special variants Metal-free 100 90 Flush-mounted in metal; distance all round 0 mm 85 85 MDS D524 1) Metal-free 100 93 On metal, distance 0 mm 96 89 Flush-mounted in metal; distance all round 0 mm 86 82 Metal-free 100 90 On metal, distance 25 mm 90 75 Flush-mounted in metal; distance all round 50 mm 80 70 Metal-free 100 94 On metal, distance 0 mm 100 94 MDS D526 1) MDS D528 4.3.4.3 Reader without direct metal influence 1) Mounting the transponder on or in metal is only possible with the appropriate spacer or if there is adequate clearance to the metal. 2) Values of > 100 % related to non metal surroundings can occur if transponders were developed specifically for mounting in/on metallic surroundings. RF240R The RF240R can be flush-mounted in metal. Please allow for a possible reduction in the field data values. To avoid reduction, the distance a should be ≥ 20 mm. Figure 4-11 Metal-free space RF240R SIMATIC RF200 60 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Table 4- 23 Reduction of field data due to metal, range as %: Transponder and RF240R Transponder MDS D100 1) MDS D124 1) MDS D126 1) MDS D160 1) MDS D165 MDS D200 1) MDS D261 MDS D324 1) MDS D400 1) MDS D422 MDS D423 MDS D424 1) Reader without direct metal influence Reader on metal Reader flushmounted in metal (metal plate) (all round 20 mm) Without metal 100 95 80 On metal, distance 20 mm 95 90 75 Flush-mounted in metal; distance all round 20 mm 90 75 70 Without metal 100 85 75 On metal, distance 15 mm 90 80 75 Flush-mounted in metal; distance all round 25 mm 85 70 65 Without metal 100 80 70 On metal, distance 25 mm 80 75 60 Flush-mounted in metal; distance all round 50 mm 70 55 55 Without metal 100 90 80 On metal, distance 10 mm 90 85 80 Without metal 100 95 75 On metal, distance 25 mm 75 70 65 Without metal 100 95 85 On metal, distance 20 mm 95 80 70 Flush-mounted in metal, distance all round 20 mm 70 60 50 Without metal 100 90 90 On metal, distance 25 mm 85 80 70 Without metal 100 90 80 On metal, distance 15 mm 95 85 80 Flush-mounted in metal; distance all round 25 mm 90 75 70 Without metal 100 90 80 On metal, distance 20 mm 80 75 55 Flush-mounted in metal, distance all round 20 mm 75 70 50 Without metal 100 90 85 Flush-mounted in metal; distance all round 0 mm 90 60 40 Without metal 100 95 90 On metal, distance 0 mm 150 2) 140 2) 140 2) Flush-mounted in metal; distance all round 10 mm 70 60 60 Without metal 100 85 80 On metal, distance 15 mm 90 80 75 SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 61 Planning the RF200 system 4.3 Installation guidelines Transponder Reader without direct metal influence Reader on metal Reader flushmounted in metal (metal plate) (all round 20 mm) Flush-mounted in metal; distance all round 25 mm 80 70 65 Without metal 100 90 85 On metal, distance 0 mm 95 85 80 Without metal 100 80 70 On metal, distance 25 mm 90 80 70 Flush-mounted in metal; 85 65 60 Without metal 100 90 85 On metal, distance 0 mm 95 85 83 Without metal 100 90 80 On metal, distance 0 mm 90 85 80 Metal-free 100 90 85 Flush-mounted in metal; distance all round 0 mm 90 60 40 MDS D522 Special variant Metal-free 100 90 85 Flush-mounted in metal; distance all round 0 mm 90 60 40 MDS D524 1) Metal-free 100 85 80 On metal, distance 0 mm 90 80 75 Flush-mounted in metal; distance all round 0 mm 80 70 65 Metal-free 100 80 70 On metal, distance 25 mm 90 80 70 Flush-mounted in metal; distance all round 50 mm 85 65 60 Metal-free 100 90 85 On metal, distance 0 mm 95 85 83 MDS D425 MDS D426 1) Distance all-round 50 mm MDS D428 MDS D460 1) MDS D522 MDS D526 1) MDS D528 1) Mounting the transponder on or in metal is only possible with the appropriate spacer or if there is adequate clearance to the metal. 2) Values of > 100 % related to non metal surroundings can occur if transponders were developed specifically for mounting in/on metallic surroundings. SIMATIC RF200 62 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines 4.3.4.4 RF250R The RF250R reader is operated with the external antennas ANT 3, 8, 12, 18 and 30. The antennas can be flush-mounted in metal. Please allow for a possible reduction in the field data values. Figure 4-12 Metal-free space for ANT 8 / ANT 12 and ANT 18 / ANT 30 Table 4- 24 Reduction of field data due to metal, range as %: Transponder and RF250R with ANT 1 Transponder ANT 1 without metal ANT 1 on metal ANT 1 mounted in metal (all round 40 mm) MDS D1001) Without metal 100 85 80 On metal; distance 20 mm 70 60 65 Flush-mounted in metal; distance all round 20 mm 60 45 45 100 95 85 On metal; distance 15 mm 85 85 80 Flush-mounted in metal; distance all round 20 mm 85 80 50 MDS D1241) Without metal MDS D1261) Without metal 100 85 85 On metal; distance 25 mm 85 75 75 Flush-mounted in metal; distance all round 50 mm 80 70 70 100 90 85 On metal; distance 30 mm 95 85 85 Flush-mounted in metal; distance all round 100 mm 95 85 85 MDS D1391) Without metal MDS D1601) Without metal MDS D165 100 95 90 On metal; distance 10 mm 85 85 80 Without metal 100 85 85 On metal; distance 25 mm 90 80 75 100 85 80 On metal; distance 20 mm 85 75 75 Flush-mounted in metal; distance all round 20 mm 75 65 65 MDS D2001) Without metal SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 63 Planning the RF200 system 4.3 Installation guidelines Transponder ANT 1 without metal ANT 1 on metal ANT 1 mounted in metal (all round 40 mm) MDS D261 Without metal 100 90 85 On metal; distance 25 mm 85 80 80 100 85 85 On metal; distance 15 mm 90 80 80 Flush-mounted in metal; distance all round 25 mm 80 75 65 MDS D3241) Without metal MDS D3391) Without metal 100 90 85 On metal; distance 30 mm 95 85 85 Flush-mounted in metal; distance all round 100 mm 95 85 85 100 90 85 On metal; distance 20 mm 80 70 65 Flush-mounted in metal; distance all round 20 mm 65 60 60 MDS D4001) Without metal MDS D423 Without metal 100 90 90 On metal; distance 0 mm 1152) 1152) 1152) Flush-mounted in metal; distance all round 0 mm 80 65 65 100 90 75 On metal; distance 15 mm 85 80 75 Flush-mounted in metal; distance all round 25 mm 75 70 70 Without metal 100 95 95 MDS D4241) Without metal MDS D425 On metal; distance 0 mm 90 85 85 100 90 85 On metal; distance 25 mm 85 80 75 Flush-mounted in metal; distance all round 50 mm 80 75 70 Without metal 100 90 85 MDS D4261) Without metal MDS D428 On metal; distance 0 mm MDS D4601) Without metal On metal; distance 10 mm 80 80 90 80 85 80 75 100 90 75 On metal; distance 15 mm 85 80 75 Flush-mounted in metal; distance all round 25 mm 75 70 70 Without metal 100 95 95 MDS D5241) Without metal MDS D525 85 100 On metal; distance 0 mm MDS D5261) Without metal On metal; distance 25 mm 90 85 85 100 90 85 85 80 75 SIMATIC RF200 64 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Transponder ANT 1 without metal ANT 1 on metal ANT 1 mounted in metal (all round 40 mm) MDS D528 Flush-mounted in metal; distance all round 50 mm 80 75 70 Without metal 100 90 85 On metal; distance 0 mm 85 80 80 1) Mounting the transponder on or in metal is only possible with the appropriate spacer or if there is adequate clearance to the metal. 2) Values of > 100 % can occur if transponders were developed specifically for mounting in/on metallic surroundings. Table 4- 25 Reduction of field data due to metal, range as %: Transponder and RF250R with ANT 3 Transponder RF250R with ANT 3 Antenna without metal Antenna flushmounted in metal (all round 20 mm) MDS D124 1) MDS D126 1) MDS D160 1) MDS D324 1) MDS D422 MDS D423 MDS D424 1) Without metal 100 80 On metal, distance 15 mm 90 75 Flush-mounted in metal; distance all round 25 mm 75 70 Without metal 100 80 On metal, distance 25 mm 85 75 Flush-mounted in metal; distance all round 50 mm 60 50 Without metal 100 85 On metal, distance 10 mm 95 80 Without metal 100 80 On metal, distance 15 mm 95 75 Flush-mounted in metal; distance all round 25 mm 85 70 Without metal 100 95 Flush-mounted in metal; distance all round 0 mm 95 80 Without metal 100 90 On metal, distance 0 mm 130 Flush-mounted in metal; distance all round 10 mm 80 70 Without metal 100 85 On metal, distance 15 mm 90 75 Flush-mounted in metal; distance all round 25 mm 75 70 2) 110 2) SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 65 Planning the RF200 system 4.3 Installation guidelines Transponder RF250R with ANT 3 Antenna without metal Antenna flushmounted in metal (all round 20 mm) MDS D425 Without metal 100 90 On metal, distance 0 mm 95 75 Without metal 100 70 On metal, distance 25 mm 90 65 Flush-mounted in metal; distance all round 25 mm 55 45 Without metal 100 90 On metal, distance 0 mm 100 90 Without metal 100 85 On metal, distance 10 mm 90 75 Without metal 100 95 Flush-mounted in metal; distance all round 0 mm 95 80 MDS D522 Special variants Without metal 100 95 Flush-mounted in metal; distance all round 0 mm 95 80 MDS D524 1) Without metal 100 85 On metal, distance 15 mm 90 75 Flush-mounted in metal; distance all round 25 mm 75 70 Without metal 100 70 On metal, distance 25 mm 90 65 Flush-mounted in metal; distance all round 25 mm 55 45 Without metal 100 90 On metal, distance 0 mm 100 90 MDS D426 1) MDS D428 MDS D460 1) MDS D522 MDS D526 1) MDS D528 1) Mounting the transponder on or in metal is only possible with the appropriate spacer or if there is adequate clearance to the metal. 2) Values of > 100 % related to non metal surroundings can occur if transponders were developed specifically for mounting in/on metallic surroundings. SIMATIC RF200 66 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Table 4- 26 Reduction of field data due to metal, range as %: Transponder and RF250R with ANT 8 Transponder MDS D117 MDS D127 MDS D421 MDS D521 Table 4- 27 RF250R with ANT 8 Antenna without metal Antenna flushmounted in metal Without metal 100 85 Flush-mounted in metal; distance all round 0 mm 65 55 Without metal 100 85 Flush-mounted in metal; distance all round 0 mm 70 60 Without metal 100 85 Flush-mounted in metal; distance all round 0 mm 75 70 Without metal 100 85 Flush-mounted in metal; distance all round 0 mm 75 70 Reduction of field data due to metal, range as %: Transponder and RF250R with ANT 12 Transponder RF250R with ANT 12 Antenna without metal Antenna flushmounted in metal (all round 7 mm) MDS D117 MDS D127 MDS D160 1) MDS D421 MDS D422 MDS D425 Without metal 100 85 Flush-mounted in metal; distance all round 0 mm 50 40 Without metal 100 85 Flush-mounted in metal; distance all round 0 mm 65 50 Without metal 100 90 On metal, distance 10 mm 90 85 Without metal 100 90 Flush-mounted in metal; distance all round 0 mm 65 45 Without metal 100 90 Flush-mounted in metal; distance all round 0 mm 90 75 Without metal 100 On metal, distance 0 mm MDS D428 Without metal MDS 90 100 100 85 110 2) 95 Without metal 100 95 On metal, distance 10 mm 90 80 Flush-mounted in metal; distance all round 0 mm 85 75 On metal, distance 0 mm D460 1) 115 2) SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 67 Planning the RF200 system 4.3 Installation guidelines Transponder RF250R with ANT 12 Antenna without metal Antenna flushmounted in metal (all round 7 mm) MDS D521 MDS D522 MDS D528 Without metal 100 90 Flush-mounted in metal; distance all round 0 mm 65 45 Without metal 100 90 Flush-mounted in metal; distance all round 0 mm 90 75 100 85 110 2) 95 Without metal On metal, distance 0 mm 1) Mounting the transponder on or in metal is only possible with the appropriate spacer or if there is adequate clearance to the metal. 2) Values of > 100 % related to non metal surroundings can occur if transponders were developed specifically for mounting in/on metallic surroundings. Table 4- 28 Reduction of field data due to metal, range as %: Transponder and RF250R with ANT 18 Transponder RF250R with ANT 18 Antenna without metal Antenna flushmounted in metal (all round 10 mm) MDS D124 1) MDS D160 1) MDS D324 1) MDS D421 MDS D422 MDS D423 MDS D424 1) Without metal 100 80 On metal, distance 15 mm 100 80 Flush-mounted in metal; distance all round 25 mm 95 70 Without metal 100 90 On metal, distance 10 mm 100 90 Without metal 100 80 On metal, distance 15 mm 100 80 Flush-mounted in metal; distance all round 25 mm 95 75 Without metal 100 85 Flush-mounted in metal; distance all round 0 mm 65 50 Without metal 100 100 Flush-mounted in metal; distance all round 0 mm 90 90 Without metal 100 85 On metal, distance 0 mm 120 Flush-mounted in metal; distance all round 10 mm 90 75 Without metal 100 75 On metal, distance 15 mm 95 75 2) 110 2) SIMATIC RF200 68 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Transponder RF250R with ANT 18 Antenna without metal Antenna flushmounted in metal (all round 10 mm) Flush-mounted in metal; distance all round 25 mm 95 75 Without metal 100 90 On metal, distance 0 mm 100 90 Without metal 100 85 On metal, distance 0 mm 100 85 Without metal 100 85 On metal, distance 10 mm 100 85 Without metal 100 85 Flush-mounted in metal; distance all round 0 mm 65 50 Without metal 100 100 Flush-mounted in metal; distance all round 0 mm 90 90 MDS D522 Special variants Without metal 100 100 Flush-mounted in metal; distance all round 0 mm 90 90 MDS D524 1) Without metal 100 75 On metal, distance 15 mm 95 75 Flush-mounted in metal; distance all round 25 mm 95 75 Without metal 100 85 On metal, distance 0 mm 100 85 MDS D425 MDS D428 MDS D460 1) MDS D521 MDS D522 MDS D528 1) Mounting the transponder on or in metal is only possible with the appropriate spacer or if there is adequate clearance to the metal. 2) Values of > 100 % related to non metal surroundings can occur if transponders were developed specifically for mounting in/on metallic surroundings. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 69 Planning the RF200 system 4.3 Installation guidelines Table 4- 29 Reduction of field data due to metal, range as %: Transponder and RF250R with ANT 30 Transponder RF250R with ANT 30 Antenna without metal Antenna flushmounted in metal (all round 20 mm) MDS D124 1) MDS D126 1) MDS D160 1) MDS D324 1) MDS D422 MDS D423 MDS D424 1) MDS D425 MDS D426 1) MDS D428 MDS D460 1) MDS D522 Without metal 100 80 On metal, distance 15 mm 90 75 Flush-mounted in metal; distance all round 25 mm 75 70 Without metal 100 80 On metal, distance 25 mm 85 75 Flush-mounted in metal; distance all round 50 mm 60 50 Without metal 100 85 On metal, distance 10 mm 95 80 Without metal 100 80 On metal, distance 15 mm 95 75 Flush-mounted in metal; distance all round 25 mm 85 70 Without metal 100 95 Flush-mounted in metal; distance all round 0 mm 95 80 Without metal 100 90 On metal, distance 0 mm 130 2) 110 2) Flush-mounted in metal; distance all round 10 mm 80 70 Without metal 100 85 On metal, distance 15 mm 90 75 Flush-mounted in metal; distance all round 25 mm 75 70 Without metal 100 90 On metal, distance 0 mm 95 75 Without metal 100 70 On metal, distance 25 mm 90 65 Flush-mounted in metal; distance all round 25 mm 55 45 Without metal 100 90 On metal, distance 0 mm 100 90 Without metal 100 85 On metal, distance 10 mm 90 75 Without metal 100 95 Flush-mounted in metal; distance all round 0 mm 95 80 SIMATIC RF200 70 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Transponder RF250R with ANT 30 Antenna without metal Antenna flushmounted in metal (all round 20 mm) MDS D522 Special variants Without metal 100 95 Flush-mounted in metal; distance all round 0 mm 95 80 MDS D524 1) Without metal 100 85 On metal, distance 15 mm 90 75 Flush-mounted in metal; distance all round 25 mm 75 70 Without metal 100 70 On metal, distance 25 mm 90 65 Flush-mounted in metal; distance all round 25 mm 55 45 Without metal 100 90 On metal, distance 0 mm 100 90 MDS D526 1) MDS D528 4.3.4.5 1) Mounting the transponder on or in metal is only possible with the appropriate spacer or if there is adequate clearance to the metal. 2) Values of > 100 % related to non metal surroundings can occur if transponders were developed specifically for mounting in/on metallic surroundings. RF260R The RF260R can be flush-mounted in metal. Please allow for a possible reduction in the field data values. To avoid reduction, the distance a should be ≥ 20 mm. Figure 4-13 Metal-free space for RF260R SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 71 Planning the RF200 system 4.3 Installation guidelines Table 4- 30 Reduction of field data due to metal, range as %: Transponder and RF260R Transponder MDS D100 1) MDS D124 1) MDS D126 1) MDS D139 1) Reader without metal direct metal influence Reader on metal Reader flushmounted in metal (metal plate) (all round 20 mm) Without metal 100 85 65 On metal, distance 20 mm 70 65 50 Flush-mounted in metal; distance all round 20 mm 4) 65 50 40 Without metal 100 93 75 On metal, distance 15 mm 95 85 70 Flush-mounted in metal; distance all round 25 mm 2) 78 75 65 Without metal 100 85 73 On metal, distance 25 mm 75 68 60 Flush-mounted in metal; distance all round 50 mm 3) 55 53 40 Without metal 100 90 75 95 90 75 Without metal 100 90 75 On metal, distance 10 mm 90 80 80 Without metal 100 85 65 On metal; distance 25 mm 4) 65 60 45 Without metal 100 85 70 On metal, distance 20 mm 70 65 50 Flush-mounted in metal, distance all round 20 mm 3) 55 50 45 Without metal 100 85 70 On metal; distance 25 mm 3) 80 70 60 Without metal 100 90 75 On metal, distance 15 mm 90 80 70 Flush-mounted in metal; distance all round 25 mm 2) 70 65 55 Without metal 100 90 75 On metal; distance 30 mm 4) 95 90 75 Without metal 100 85 70 On metal, distance 20 mm 70 65 50 Flush-mounted in metal; distance all round 20 mm 4) 55 50 45 Without metal 100 On metal; distance 30 mm MDS D160 1) MDS D165 MDS D200 1) MDS D261 MDS D324 1) MDS D339 1) MDS D400 1) MDS D423 4) On metal, distance 0 mm Flush-mounted in metal; distance all round 10 mm 2) 120 75 5) 95 115 65 85 5) 110 5) 60 SIMATIC RF200 72 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Transponder MDS D424 1) MDS D426 1) MDS D428 MDS MDS D460 1) D524 1) MDS D526 1) MDS D528 Without metal Reader without metal direct metal influence Reader on metal Reader flushmounted in metal (metal plate) (all round 20 mm) 100 90 80 On metal, distance 15 mm 90 80 70 Flush-mounted in metal; distance all round 25 mm 2) 60 60 50 Without metal 100 100 73 On metal, distance 25 mm 88 85 68 Flush-mounted in metal; distance all round 50 mm 3) 65 55 55 Without metal 100 90 90 On metal, distance 0 mm 90 90 85 Without metal 100 95 90 On metal, distance 10 mm 90 85 80 Without metal 100 90 80 On metal, distance 15 mm 90 80 70 Flush-mounted in metal; distance all round 25 mm 2) 60 60 50 Without metal 100 100 73 On metal, distance 25 mm 88 85 68 Flush-mounted in metal; distance all round 50 mm 3) 65 55 55 Without metal 100 90 90 On metal, distance 0 mm 90 90 85 1) Mounting the transponder on or in metal is only possible with the appropriate spacer or if there is adequate clearance to the metal. 2) Transponder flush-mounted in metal; minimum distance to reader 5 mm 3) Transponder flush-mounted in metal; minimum distance to reader 10 mm 4) Transponder flush-mounted in metal; minimum distance to reader 15 mm 5) Values > 100 % can occur if transponders were developed specifically for mounting in/on metallic surroundings. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 73 Planning the RF200 system 4.3 Installation guidelines 4.3.4.6 RF280R The RF280R can be flush-mounted in metal. Please allow for a possible reduction in the field data values. To avoid reduction, the distance a should be ≥ 20 mm. Figure 4-14 Metal-free area RF280R Table 4- 31 Reduction of field data due to metal, range as %: Transponder and RF280R Transponder MDS D1001) Without metal 95 80 65 60 55 Flush-mounted in metal; distance all round 20 mm 2) 55 50 45 100 95 90 On metal; distance 15 mm 95 90 85 Flush-mounted in metal; distance all round 20 mm 2) 70 65 50 100 90 80 On metal; distance 25 mm 80 75 70 Flush-mounted in metal; distance all round 50 mm 3) 75 65 65 MDS D1391) Without metal 100 90 75 On metal; distance 30 mm 95 85 70 Flush-mounted in metal; distance all round 100 mm 4) 90 80 70 100 95 90 MDS D1601) Without metal On metal; distance 10 mm 85 85 80 100 90 80 80 75 70 Without metal 100 90 80 On metal; distance 20 mm 80 75 70 2) Without metal On metal; distance 25 mm MDS Flush-mounted in metal (20 mm all-round) 100 MDS D1261) Without metal D2001) Reader on metal (metal plate) On metal; distance 20 mm MDS D1241) Without metal MDS D165 Reader without metal direct metal influence 4) SIMATIC RF200 74 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Transponder MDS D261 Reader without metal direct metal influence Reader on metal (metal plate) Flush-mounted in metal (20 mm all-round) Flush-mounted in metal; distance all round 20 mm 3) 65 60 55 Without metal 100 95 85 85 80 75 On metal; distance 25 mm MDS D3241) 4) Without metal 100 95 85 On metal; distance 15 mm 85 85 80 Flush-mounted in metal; distance all round 25 mm 2) 70 65 60 100 90 80 On metal; distance 30 mm 85 80 75 Flush-mounted in metal; distance all round 100 mm 4) 80 75 70 MDS D3391) Without metal MDS D4001) Without metal 100 90 80 On metal; distance 20 mm 75 70 60 Flush-mounted in metal; distance all round 20 mm 4) 60 60 55 Without metal 100 95 85 1005) 1005) 905) 75 65 60 100 90 75 On metal; distance 15 mm 75 75 60 Flush-mounted in metal; distance all round 25 mm 2) 60 55 40 MDS D425 Without metal 100 70 90 MDS D525 On metal; distance 0 mm 2) 75 70 60 Without metal 100 90 80 MDS D423 On metal; distance 0 mm Flush-mounted in metal; distance all round 10 mm 2) MDS D4241) Without metal MDS MDS D5241) D4261) MDS D5261) On metal; distance 25 mm 80 75 70 Flush-mounted in metal; distance all round 50 mm 3) 75 65 65 MDS D428 Without metal 100 90 80 MDS D528 On metal; distance 0 mm 2) 85 80 65 Without metal 100 95 80 On metal; distance 10 mm 2) 80 75 60 MDS D4601) 1) Mounting the transponder on or in metal is only possible with the appropriate spacer or if there is adequate clearance to the metal. 2) Transponder flush-mounted in metal; minimum distance to reader 5 mm 3) Transponder flush-mounted in metal; minimum distance to reader 10 mm 4) Transponder flush-mounted in metal; minimum distance to reader 15 mm 5) Values > 100 % in relation to non-metal surroundings can occur if transponders were developed specifically for mounting in/on metallic surroundings. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 75 Planning the RF200 system 4.3 Installation guidelines 4.3.4.7 RF290R The RF290R reader is operated with the external antennas ANT D5, D6 and D10. The antennas can be flush-mounted in metal. Please allow for a possible reduction in the field data values. To avoid reduction, the distance a should be ≥ 150 or 200 mm. Figure 4-15 Metal-free space for ANT D5 Table 4- 32 Reduction of field data due to metal, range as %: Transponder and RF290R with ANT D5 Transponder RF290R with ANT D5 Antenna on metal (metal plate) MDS D100 1) MDS D124 1) MDS D126 1) MDS D139 1) MDS D160 1) MDS D165 MDS D200 1) Antenna flushmounted in metal (all round 150 mm) Without metal 100 95 On metal, distance 20 mm 65 60 Flush-mounted in metal; distance all round 20 mm 45 40 Without metal 100 95 On metal, distance 15 mm 85 80 Flush-mounted in metal; distance all round 25 mm 65 60 Without metal 100 95 On metal, distance 25 mm 70 65 Flush-mounted in metal; distance all round 50 mm 55 50 Without metal 100 95 On metal, distance 30 mm 90 85 Without metal 100 95 On metal, distance 10 mm 70 65 Without metal 100 95 On metal, distance 25 mm 65 60 Without metal 100 95 On metal, distance 20 mm 65 60 SIMATIC RF200 76 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Transponder RF290R with ANT D5 Antenna on metal (metal plate) MDS D261 MDS D324 1) MDS MDS D339 1) D400 1) MDS D424 1) MDS D426 1) MDS D460 1) 1) Antenna flushmounted in metal (all round 150 mm) Flush-mounted in metal; distance all round 20 mm 45 40 Without metal 100 95 On metal, distance 25 mm 65 60 Without metal 100 95 On metal, distance 15 mm 75 70 Without metal 100 95 On metal, distance 30 mm 90 85 Without metal 100 95 On metal, distance 20 mm 65 60 Flush-mounted in metal; distance all round 20 mm 45 40 Without metal 100 95 On metal, distance 15 mm 75 70 Without metal 100 95 On metal, distance 25 mm 70 65 Flush-mounted in metal; distance all round 50 mm 50 45 Without metal 100 95 On metal, distance 10 mm 70 65 Mounting the transponder on or in metal is only possible with the appropriate spacer or if there is adequate clearance to the metal. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 77 Planning the RF200 system 4.3 Installation guidelines Table 4- 33 Reduction of field data due to metal, range as %: Transponder and RF290R with ANT D6 Transponder RF290R with ANT D6 Antenna on metal (metal plate) MDS D100 1) MDS D124 1) MDS MDS D126 1) D139 1) MDS D160 1) MDS D165 MDS D200 1) MDS D261 MDS D324 1) MDS D339 1) MDS MDS MDS 1) D400 1) D424 1) D426 1) Without metal Antenna flushmounted in metal (all round 200 mm) 100 95 On metal, distance 20 mm 65 60 Without metal 100 95 On metal, distance 25 mm 80 75 Without metal 100 95 On metal, distance 25 mm 65 60 Without metal 100 90 On metal, distance 30 mm 80 70 Without metal 100 90 On metal, distance 25 mm 60 55 Without metal 100 95 On metal, distance 20 mm 50 45 Without metal 100 95 On metal, distance 20 mm 65 60 Without metal 100 95 On metal, distance 20 mm 50 45 Without metal 100 95 On metal, distance 25 mm 75 70 Without metal 100 90 On metal, distance 30 mm 80 70 Without metal 100 95 On metal, distance 20 mm 60 55 Without metal 100 95 On metal, distance 25 mm 75 70 Without metal 100 95 On metal, distance 25 mm 65 60 Mounting the transponder on or in metal is only possible with the appropriate spacer or if there is adequate clearance to the metal. SIMATIC RF200 78 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Table 4- 34 Reduction of field data due to metal, range as %: Transponder and RF290R with ANT D10 Transponder RF290R with ANT D10 Antenna on metal (metal plate) MDS D100 1) MDS D124 1) MDS MDS D126 1) D139 1) MDS D160 1) MDS D165 MDS D200 1) MDS D261 MDS D324 1) MDS D339 1) MDS MDS MDS D400 1) D424 1) D426 1) MDS D524 1) MDS 1) D526 1) Without metal 100 Antenna flushmounted in metal (all round 200 mm) 95 On metal, distance 20 mm 50 40 Without metal 100 90 On metal, distance 25 mm 70 60 Without metal 100 95 On metal, distance 25 mm 65 60 Without metal 100 90 On metal, distance 30 mm 80 70 Without metal 100 90 On metal, distance 25 mm 60 55 Without metal 100 90 On metal, distance 20 mm 40 30 Without metal 100 95 On metal, distance 20 mm 50 40 Without metal 100 90 On metal, distance 20 mm 40 30 Without metal 100 90 On metal, distance 25 mm 70 60 Without metal 100 90 On metal, distance 30 mm 80 70 Without metal 100 95 On metal, distance 20 mm 50 40 Without metal 100 90 On metal, distance 25 mm 70 60 Without metal 100 95 On metal, distance 25 mm 70 65 Without metal 100 90 On metal, distance 25 mm 70 60 Without metal 100 95 On metal, distance 25 mm 70 65 Mounting the transponder on or in metal is only possible with the appropriate spacer or if there is adequate clearance to the metal. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 79 Planning the RF200 system 4.3 Installation guidelines 4.3.5 Installation and connection of 2 to 6 antennas with one RF290R reader If several antennas need to be operated on one reader, this can be achieved by using the antenna splitter or the antenna multiplexer RF260X. Note that the antenna splitter is a purely passive device that splits the power at the input to two outputs and therefore halves it. This is possible both in PC mode (RS-232) and CM mode (RS-422). You can cascade the antenna splitters in such a way that up to 4 antennas can be connected at the same time. The antenna multiplexer RF260X works only in PC mode (RS-232) in time division multiplex mode. This means that each antenna operates with full power for a certain time before the device moves on automatically to the next antenna. The antenna multiplexer normally operates in scan mode or buffered read mode which with suitable parameter assignment add the information about the antenna number to the reply of the transponder. You can operate up to six antennas on one reader via the multiplexer. 4.3.5.1 Installation options with the antenna splitter (2-4 antennas) Possible configurations of the antennas The antenna installations described here have been designed for reading smartlabels (transponders) on goods on conveyor belts, conveyor systems or pallets. A prerequisite is that there are no magnetically conducting materials (e.g. metal) in the vicinity of the antenna or the label. SIMATIC RF200 80 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Figure 4-16 Possible configuration of RF290R with ANT D5/D6/D10 SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 81 Planning the RF200 system 4.3 Installation guidelines Installation examples Figure 4-17 Installation example with 2 ANT D6 (portal) Figure 4-18 Installation example with ANT D6 (C arrangement) SIMATIC RF200 82 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Figure 4-19 Installation example with ANT D6 (tunnel) Note The minimum spacings between the antennas for operation with only one reader may be less than the distances described because this configuration has the same phase. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 83 Planning the RF200 system 4.3 Installation guidelines 4.3.5.2 Antenna installation Configuring instructions The antenna installation described below enables detection of transponders moving horizontally through the installation. Depending on the installation (antennas exactly opposite each other or offset in parallel), the label is aligned in parallel with the antennas or arbitrarily. The size of the sensing range depends on the label alignment: Note Remember that the entire acquisition range of the antenna is larger than the transmission window in which the transponder is normally configured. This means there can be label alignments where even labels outside the transmission window will be identified. Labels aligned in parallel with the antennas, for example, can also be detected at larger distances beside or outside the antenna range. For this reason, goods with labels must not be stored within a distance of up to 0.5 m from the installation. If this cannot be complied with, the antennas must be shielded. To achieve three-dimensional detection of the labels in the sensing range, the following requirements must be met: • The gate width must be less than or equal to 800 mm. • The antenna size of the labels should be at least the size of an ISO card (85 mm x 54 mm). • The distance from label to label must be greater than 100 mm. The distance from label to label can be reduced if the gate width is correspondingly reduced. This applies especially for distances under 50 mm. • There should be no more than 16 labels within the sensing range of the antennas at the same time. The number of labels can be increased if the gate width is correspondingly reduced and the maximum speed suitably adapted. • The maximum speed of the labels must not exceed 1 m/s. (This depends on the number and alignment of the labels, the number of data blocks to be processed, the data protocol required and the label type). • To the front and sides of the antenna, there must be a distance of more than 150 mm to metal parts. • There must be no interference to the write/read device from other electrical equipment in the surrounding area. Note The RF290R reader is not capable of multitag operation in the CM mode. SIMATIC RF200 84 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Required components For installation with ● 2 antennas (gate) ● 3 antennas (C arrangement) ● 4 antennas (tunnel) the following components are required: Table 4- 35 Components required for setting up with 2, 3 or 4 antennas Number for installation with 2 ant. 3 ant. Component Article number 4 ant. Basic device: RF290R (↔ CM or PC) RF290R: 6GT2821-0AC12 optionally: ASM 475: 6GT2002-0GA10 ASM 456: 6GT2002-0ED00 RF170C: 6GT2002-0HD00 RF180C: 6GT2002-0JD00 RF182C: 6GT2002-0JD10 Antenna ANT D5 / D6 / D10 optionally: ANT D5: 6GT2698-5AA10 ANT D6: 6GT2698-5AB00 ANT D10: 6GT2698-5AF00 With ANT D6 if required: cover 6GT2698-5AD00 Antenna splitter 6GT2603-0AC00 Wide-range power supply unit for SIMATIC RF systems (for PC mode only) EU: 6GT2898-0AA00 UK: 6GT2898-0AA10 US: 6GT2898-0AA20 24 V connecting cable, length 5 m (for PC mode only) 6GT2491-1HH50 Connecting cable: RF290R ↔ PC or RF290R ↔ CM 6GT2891-4KH ... optionally: 6GT2891-4F ... 6GT2891-4EH ... Installation information The cables on the antennas and the antenna splitter are 3.3 m or 10.5 m long. The write/read device must be installed in the vicinity of the antennas. If there are greater distances between the write/read device and the antennas, the antenna cable can be increased by 7.2 m with the extension (6GT2691-0DH72). This results in shorter ranges. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 85 Planning the RF200 system 4.3 Installation guidelines Metal-free space To guarantee perfect functioning of the individual installation versions, all larger metal parts in the vicinity of the antennas must be removed. Figure 4-20 Metal-free space, side view (based on the example of a tunnel arrangement on a conveyor belt) approx. half antenna length min. 100 mm max. 600 mm Metal-free space Figure 4-21 Metal-free space, view from above (based on the example of a tunnel arrangement on a conveyor belt) Metal in the vicinity of the antennas If metal in the vicinity of the antennas cannot be avoided, the following must be noted: ● There must be a minimum allround gap of 100 mm between the antenna and metal. Serious loss of sensing range must be expected above 50 mm. There is no discernible influence at distances greater than 150 mm from the metal. ● The influence of the metal depends heavily on its size and shape. Thin metal rods have less influence on the magnetic field than large surfaces. ● Larger metal surfaces (edge length > 50 mm) in parallel with the antennas or labels result in a short-circuit of the magnetic lines of force. As a result, the labels cannot be read. ● Metal parts under the conveyor belt change the direction of the magnetic lines of force. Serious loss of sensing range must be expected as a result. Horizontally aligned labels cannot be read in such cases. SIMATIC RF200 86 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines ● The metal parts must not form closed loops or circuits. If necessary, these must be electrically interrupted at one point. ● The metal parts in the immediate vicinity of the antenna must be grounded in a mesh with a good HF connection. ● Since the write/read device is installed in a metal housing, and the antennas can couple into the cables to the write/read device, it must be installed at a distance of at least 500 mm from the antennas. Notes on installing and laying the antenna cable To suppress possible interference, an EMC hinged ferrite choke must be fitted to the antenna cables (as well as the antenna cable between the reader and the antenna splitter). The coaxial cable must be wound tightly at least four times through the EMC ring core. The maximum distance between the connecting plug for the reader or the antenna splitter and the ring core must be 100 mm. The antenna cable must always be run vertically from the antennas. A minimum distance of 200 mm to the antennas must be observed as the cables continue. Otherwise, performance losses must be expected. There must be a distance of at least 300 mm between antenna cables and parallel power cables. Unrequired cable length must be secured in a bundle with a diameter of 100 to 150 mm. If the standard antenna cable is too short, it can be increased by 7.20 m with the extension. Slight range losses must be expected here. To achieve optimal read ranges, the antenna cable should not be shortened or lengthened. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 87 Planning the RF200 system 4.3 Installation guidelines 4.3.5.3 Installation options with the antenna multiplexer (2-6 antennas) You can operate up to six antennas on one reader via the multiplexer. The data is processed sequentially. Antenna switchover is performed in time-multiplex mode, so by connecting several antennas together, the processing time / activation time per antenna is lengthened accordingly. Figure 4-22 Configuration example of the antenna multiplexer with ANT D5 SIMATIC RF200 88 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines 4.3.6 Chemical resistance of the reader and transponders 4.3.6.1 Readers Overview of the readers and their housing materials The following sections describe the chemical resistance of the various transponders. The chemical resistance depends on the housing materials used to manufacture the reader. The following table provides an overview of the housing materials used for the readers RF210R, RF220R, RF240R, RF250R, RF260R and RF280R: Readers Individual parts of the reader RF210R, RF220R Sleeves Housing material of the reader Brass (copper alloy) CuZn40Pb2 Fiber-optic cable Makrolon®2405 Cap (antenna) Thermocomp OF-1008-L-EM Valox 357 RF240R, RF250R, RF260R RF280R 1) Top shell and base plate Polyamide 6.6 GF30; The chemical resistance of this plastic is listed in the section "Polyamide 6 and Polyamide 6.6 GF30 (Page 90)". Fiber-optic cable Makrolon®2405 Decorative foil Autotex V200 1) Top shell and base plate Polyamide 12; The chemical resistance of this plastic is listed in the section "Polyamide 12 (Page 91)". Fiber-optic cable Makrolon®2405 Decorative foil Autotex V200 1) Component irrelevant for resistance of the overall housing Note If you have any questions, please contact Siemens Support, see section "Service & Support (Page 377)". SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 89 Planning the RF200 system 4.3 Installation guidelines Polyamide 6 and Polyamide 6.6 GF30 Table 4- 36 Chemical resistance - PA6 and PA6.6 GF30 Substance Test conditions Rating Concentration [%] Temperature [°C] Mineral lubricants Aliphatic hydrocarbons ++++ Aromatic hydrocarbons ++++ Gasoline ++++ Weak mineral acids +++ Strong mineral acids ○ Weak organic acids ++ Strong organic acids ○ Oxidizing acids ○ Weak alkaline solutions ++ Strong alkaline solutions ○ Trichloroethylene ++++ Perchloroethylene ++++ Acetone ++++ Alcohols ++++ Hot water (hydrolysis resistance) ++ ++++ Explanation of the rating ++++ Resistant +++ Practically resistant ++ Conditionally resistant Less resistant ○ Not resistant SIMATIC RF200 90 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Polyamide 12 The resistance of the plastic housing to chemicals used in the automobile sector (e.g.: oils, greases, diesel fuel, gasoline, etc,) is not listed extra. Table 4- 37 Chemical resistance - Polyamide 12 Substance Battery acid Ammonia, gaseous Ammonia, w. Benzene Test conditions Rating Concentration [%] Temperature [°C] 30% 20 ℃ ++ 60 ℃ ++++ conc. 60 ℃ ++++ 10% 60 ℃ ++++ 20 ℃ ++++ 60 ℃ +++ Bleach solution (12.5% effective chlorine) 20 ℃ ++ Butane, gas, liquid 60 ℃ ++++ Butyl acetate (acetic acid butyl ester) 60 ℃ ++++ n(n) 20 ℃ ++++ 60 ℃ +++ 20 ℃ ++++ Calcium chloride, w. Calcium nitrate, w. 60 ℃ +++ c. s. 20 ℃ ++++ c. s. 60 ℃ +++ Chlorine 20 ℃ ○ Chrome baths, tech. 20 ℃ ○ Iron salts, w. c. s. 60 ℃ ++++ Acetic acid, w. 50% 20 ℃ ○ Ethyl alcohol, w., undenaturated 95% 20 ℃ ++++ 95% 60 ℃ +++ 50% 60 ℃ ++++ 30% 20 ℃ +++ 10% 20 ℃ ++++ 10% 60 ℃ +++ Formalin 20 ℃ +++ Glycerine 60 ℃ ++++ Isopropyl alcohol 20 ℃ ++++ Formaldehyde, w. Potassium hydroxide, w. Lysol 60 ℃ +++ 50% 60 ℃ ++++ 20 ℃ ++ Magnesium salts, w. c. s. 60 ℃ ++++ Methyl alcohol, w. 50% 60 ℃ ++++ Lactic acid, w. 50% 20 ℃ ++ 10% 20 ℃ +++ SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 91 Planning the RF200 system 4.3 Installation guidelines Substance Test conditions Concentration [%] Temperature [°C] 10% 60 ℃ Rating ++ Sodium carbonate, w. (soda) c. s. 60 ℃ ++++ Sodium chloride, w. c. s. 60 ℃ ++++ Sodium hydroxide Nickel salts, w. Nitrobenzene Phosphoric acid Propane Mercury 60 ℃ ++++ c. s. 60 ℃ ++++ 20 ℃ +++ 60 ℃ ++ 10% 20 ℃ 60 ℃ ++++ 60 ℃ ++++ Nitric acid 10% 20 ℃ Hydrochloric acid 10% 20 ℃ Sulfur dioxide low 60 ℃ ++++ Sulfuric acid 25% 20 ℃ ++ 10% 20 ℃ +++ low 60 ℃ ++++ Carbon tetrachloride 60 ℃ ++++ Toluene 20 ℃ ++++ 60 ℃ +++ Detergent high 60 ℃ ++++ Plasticizer 60 ℃ ++++ Hydrogen sulfide Explanation of the rating ++++ Resistant +++ Practically resistant ++ Conditionally resistant Less resistant ○ Not resistant w. Water solution c. s. Cold saturated SIMATIC RF200 92 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines 4.3.6.2 Transponder Overview of the transponders and their housing materials The following sections describe the resistance to chemicals of the various transponders. Resistance to chemicals depends on the housing material used to manufacture the transponders. The following table provides an overview of the housing materials of the transponders: Table 4- 38 Overview of the housing materials of the transponders Housing material Transponder Polyphenylene sulfide (PPS) MDS D117 MDS D124 (6GT2600-0AC10) MDS D139 MDS D160 MDS D339 MDS D423 Polycarbonate (PC) MDS D100 (6GT2600-0AD10) Polyvinyl chloride (PVC) MDS D100 (6GT2600-0AD00-0AX0) MDS D200 MDS D400 Epoxy resin MDS D124 (6GT2600-0AC00) MDS D324 MDS D421 MDS D424 MDS D460 MDS D521 MDS D524 PA6 MDS D127 PA6.6 GF30 MDS D126 MDS D422 MDS D425 MDS D426 MDS D428 MDS D522 MDS D526 MDS D528 SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 93 Planning the RF200 system 4.3 Installation guidelines Note Chemical substances not listed The following sections describe the resistance of the various transponders to specific substances. If you require information about chemical substances that are not listed, contact Customer Support. Polyphenylene sulfide (PPS) The data memory has special chemical resistance to solutions up to a temperature of 200 °C. A reduction in the mechanical properties has been observed in aqueous solutions of hydrochloric acid (HCl) and nitric acid (HNO3) at 80 °C. The plastic housings are resistant to all types of fuel including methanol. Table 4- 39 Chemical resistance - polyphenylene sulfide (PPS) Substance Test conditions Rating Concentration [%] Temperature [°C] Acetone 55 ℃ ++++ n-Butanol (butyl alcohol) 80 ℃ ++++ Butanone-2 (methyl ethyl ketone) 60 ℃ ++++ n-Butyl acetate 80 ℃ ++++ Brake fluid 80 ℃ ++++ Calcium chloride (saturated) 80 ℃ ++++ Diesel fuel 80 ℃ ++++ Diethyl ether 23 ℃ ++++ Frigen 113 23 ℃ ++++ Anti-freeze 120 ℃ ++++ Kerosene 60 ℃ ++++ Methanol 60 ℃ ++++ Engine oil 80 ℃ ++++ Sodium chloride (saturated) 80 ℃ ++++ Sodium hydroxide 30% 80 ℃ ++++ Sodium hypochlorite (30 or 180 days) 5% 80 ℃ ++ 5% 80 ℃ Sodium hydroxide solution 30% 90 ℃ ++++ Nitric acid 10% 23 ℃ ++++ Hydrochloric acid 10% 80 ℃ Sulfuric acid 10% 23 ℃ ++++ 10% 80 ℃ ++ 30% 23 ℃ ++++ 80 ℃ ++++ Tested fuels SIMATIC RF200 94 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Substance Test conditions Rating Concentration [%] Temperature [°C] FAM testing fluid acc. to DIN 51 604-A Toluene 80 ℃ ++ 1, 1, 1-Trichloroethane Xylene 80 ℃ ++++ Zinc chloride (saturated) 80 ℃ ++ 75 ℃ ++++ Explanation of the rating ++++ Resistant +++ Practically resistant ++ Conditionally resistant Less resistant ○ Not resistant SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 95 Planning the RF200 system 4.3 Installation guidelines Polycarbonate (PC) Table 4- 40 Chemical resistance - polycarbonate (PPS) Substance Test conditions Rating Concentration [%] Temperature [°C] Mineral lubricants Aliphatic hydrocarbons ++++ Aromatic hydrocarbons ○ Gasoline ○ Weak mineral acids ++++ Strong mineral acids ++ Weak organic acids ++++ Strong organic acids ++ Oxidizing acids ○ Weak alkaline solutions ○ Strong alkaline solutions ○ Trichloroethylene ○ Perchloroethylene ○ Acetone ○ Alcohols ++ Hot water (hydrolysis resistance) ○ ++ Explanation of the rating ++++ Resistant +++ Practically resistant ++ Conditionally resistant Less resistant ○ Not resistant SIMATIC RF200 96 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Polyvinyl chloride (PVC) Table 4- 41 Chemical resistance - polyvinyl chloride (PVC) Substance Test conditions Rating Concentration [%] Temperature [°C] Salt water 5% Sugared water 10% ++++ Acetic acid, w. 5% ++++ Sodium carbonate, w. 5% ++++ Ethyl alcohol, w. 60% ++++ Ethylene glycol 50% ++++ Fuel B (acc. to ISO 1817) ++++ Human sweat ++++ ++++ Explanation of the rating ++++ Resistant ++++ Practically resistant ++ Conditionally resistant Less resistant ○ Not resistant Epoxy resin Table 4- 42 Chemical Resistance - epoxy resin Substance Test conditions Rating Concentration [%] Temperature [°C] Allyl chloride 20 ℃ ++++ Formic acid 50% 20 ℃ ++++ 100% 20 ℃ ++ Ammonia, gaseous 20 ℃ ++++ Ammonia, liquid, water-free 20 ℃ ○ 10% 20 ℃ ++++ 40 ℃ ++++ 60 ℃ ++++ Ammonium hydroxide Ethanol Ethyl acrylate 20 ℃ ++++ Ethyl glycol 60 ℃ ++++ Gasoline, aroma-free 20 ℃ ++++ Gasoline, containing benzene 20 ℃ ++++ Benzoates (Na–, Ca– among others) 40 ℃ ++++ Benzoic acid 20 ℃ ++++ SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 97 Planning the RF200 system 4.3 Installation guidelines Substance Test conditions Rating Concentration [%] Temperature [°C] Benzene 20 ℃ Borax 60 ℃ ++++ Boric acid 20 ℃ ++++ Bromine, liquid 20 ℃ ○ Bromides (K–, Na– among others) 60 ℃ ++++ 100% 20 ℃ ++++ Bromine water 20 ℃ ○ Butadien (1.3–) 20 ℃ ++++ Butane, gaseous 20 ℃ ++++ Bromoform Butanol ++++ 20 ℃ ○ 100% 20 ℃ ++ Carbonates (ammonium–, Na– among others) 60 ℃ ++++ Chlorine, liquid 20 ℃ ○ Butyric acid Chlorine, gaseous, dry 100% 20 ℃ ○ Chlorobenzene 20 ℃ ++++ Chlorides (ammonium–, Na– among others) 60 ℃ ++++ Chloroform 20 ℃ ○ Chlorophyll 20 ℃ ++++ 100% 20 ℃ ○ 20 ℃ ++ Chlorosulfuric acid Chlorine water (saturated solution) Chromates (K–, Na– among others) Up to 50 % 40 ℃ ++++ Chromic acid Up to 30 % 20 ℃ ○ Chromosulfuric acid 20 ℃ ○ Citric acid 20 ℃ ++++ Cyanamide 20 ℃ ++++ Cyanides (K–, Na– among others) 60 ℃ ++++ Dextrin, w. 60 ℃ ++++ Diethyl ether 20 ℃ ++++ Diethylene glycol 60 ℃ ++++ Dimethyl ether 20 ℃ ++++ Dioxane 20 ℃ ○ Developer 40 ℃ ++++ Acetic acid 100% 20 ℃ ++ Ethanol 60 ℃ ++++ Fixing bath 40 ℃ ++++ Fluorides (ammonium–, K–, Na– among others) 40 ℃ ++++ Up to 40 % 20 ℃ ++++ Formaldehyde 50% 20 ℃ ++++ Formamide 100% 20 ℃ ++++ Hydrofluoric acid SIMATIC RF200 98 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.3 Installation guidelines Substance Test conditions Rating Concentration [%] Temperature [°C] Gluconic acid 20 ℃ Glycerine 60 ℃ ++++ Glycol 60 ℃ ++++ Urine 20 ℃ ++++ Uric acid 20 ℃ ++++ Hydroxides (ammonium...) 10% 20 ℃ ++++ Hydroxides (Na–, K–) ++++ 40% 20 ℃ ++++ Hydroxides (alkaline earth metal) 60 ℃ ++++ Hypochlorites (K–, Na– among others) 60 ℃ ++++ Iodides (K–, Na– among others) 60 ℃ ++++ Silicic acid 60 ℃ ++++ Up to 90 % 20 ℃ ○ 100% 40 ℃ ++++ 20 ℃ ○ Lactic acid 100% 20 ℃ ++ Mineral oils 40 ℃ ++++ Nitrates (ammonium..., K– among others) 60 ℃ ++++ Nitroglycerin 20 ℃ ○ Cresol Methanol Methylene chloride Oxalic acid 20 ℃ ++++ 1% 20 ℃ ++++ 60 ℃ ++++ 50% 60 ℃ ++++ 85% 20 ℃ ++++ Propanol 20 ℃ ++++ Nitric acid 25% 20 ℃ ○ Hydrochloric acid 10% 20 ℃ ○ Phenol Phosphates (ammonium..., Na– among others) Phosphoric acid Brine 60 ℃ ○ Sulfur dioxide 100% 20 ℃ ++ Carbon disulfide 100% 20 ℃ ○ Sulfuric acid 40% 20 ℃ ○ Sulfurous acid 20 ℃ ++ Soap solution 60 ℃ ++++ Sulphates (ammonium..., Na– among others) 60 ℃ ++++ Sulfites (ammonium..., Na– among others) 60 ℃ ○ Tar, aroma-free 60 ℃ ++++ Turpentine 20 ℃ ++++ Trichloroethylene 20 ℃ ○ SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 99 Planning the RF200 system 4.3 Installation guidelines Substance Test conditions Rating Concentration [%] Temperature [°C] 30% 20 ℃ ++++ 20 ℃ ++++ Hydrogen peroxide Tartaric acid Explanation of the rating ++++ Resistant +++ Practically resistant ++ Conditionally resistant Less resistant ○ Not resistant Polyamide 6 and Polyamide 6.6 GF30 Table 4- 43 Chemical resistance - PA6 and PA6.6 GF30 Substance Test conditions Rating Concentration [%] Temperature [°C] Mineral lubricants ++++ Aliphatic hydrocarbons ++++ Aromatic hydrocarbons ++++ Gasoline ++++ Weak mineral acids +++ Strong mineral acids ○ Weak organic acids ++ Strong organic acids ○ Oxidizing acids ○ Weak alkaline solutions ++ Strong alkaline solutions ○ Trichloroethylene ++++ Perchloroethylene ++++ Acetone ++++ Alcohols ++++ Hot water (hydrolysis resistance) ++ Explanation of the rating ++++ Resistant +++ Practically resistant ++ Conditionally resistant Less resistant ○ Not resistant SIMATIC RF200 100 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Planning the RF200 system 4.4 Further information 4.4 Further information Further information on "Fundamentals of application planning" and "EMC" can be found in RF300 system manual (https://support.industry.siemens.com/cs/ww/en/view/21738946). SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 101 Planning the RF200 system 4.4 Further information SIMATIC RF200 102 System Manual, 07/2017, J31069-D0227-U001-A9-7619 5 Readers NOTICE Pulling and plugging readers Pull or plug the reader only when the power supply is turned off If this is not observed, under certain conditions, the reader will not start up correctly and communication with a transponder will not be possible. Note IO-Link variants of the RF200 readers The IO-Link variants of the readers are not included in the system manual. You will find these in the "SIMATIC RF200 IO-Link (https://support.industry.siemens.com/cs/ww/en/view/60641859)" operating instructions. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 103 Readers 5.1 SIMATIC RF210R 5.1 SIMATIC RF210R 5.1.1 Features SIMATIC RF210R 5.1.2 Characteristics Design ① RS422 interface ② Status display Application Identification tasks on assembly lines in harsh industrial environments RF210R ordering data Article number RF210R with RS422 interface (3964R) 6GT2821-1AC10 SIMATIC RF200 104 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.1 SIMATIC RF210R 5.1.3 Pin assignment RF210R with RS422 interface Pin Pin Assignment Device end 8-pin M12 5.1.4 + 24 V - Transmit 0V + Transmit + Receive - Receive Unassigned Ground (shield) LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 1 LED LED operating display on the reader Meaning The reader is turned off. Operating voltage present, reader not initialized or antenna switched off Operating voltage present, reader initialized and antenna switched on • Operating mode "with presence": Transponder present • Operating mode "without presence": Transponder present and command currently being executed There is an error. The number of flashes provides information about the current error. You can find more information on error messages in the section "Error codes of the RF200 readers (Page 329)". The optical error display is only reset if the corresponding reset parameter ("option_1 = 2") is set (see product information "SIMATIC RF200 Command Set (https://support.industry.siemens.com/cs/ww/en/view/44864850)"). SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 105 Readers 5.1 SIMATIC RF210R 5.1.5 Minimum distance between RF210R readers RF210R side by side ≥ 60 mm Figure 5-1 Minimum distance between RF210R readers RF210R face to face ≥ 100 mm Figure 5-2 Face-to-face distance between two RF210Rs SIMATIC RF200 106 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.1 SIMATIC RF210R 5.1.6 Technical specifications of the RF210R reader Table 5- 2 Technical specifications of the RF210R reader 6GT2821-1AC10 Product type designation SIMATIC RF210R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 20 mm Maximum data transmission speed reader ↔ transponder ISO tags • Read • approx. 1500 bytes/s • Write • approx. 1500 bytes/s Typical transmission time for user data per byte • for write access • 0.6 ms • for read access • 0.6 ms Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader see section "Field data (Page 39)" MTBF (Mean Time Between Failures) 505 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication RS-422 Antenna integrated Mechanical specifications Housing • Material • Brass, nickel-plated • Color • Silver Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 50 mA Permitted ambient conditions Ambient temperature • During operation • -20 … +70 °C SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 107 Readers 5.1 SIMATIC RF210R 6GT2821-1AC10 • During transportation and storage • -25 … +85 °C Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M3 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weight 5.1.7 Dimensions (∅ x thread x L) M18 x 1 x 83 mm Weight 65 g Type of mounting 2x nuts M18 x 1 Cable length for RS-422 interface, maximum 1000 m LED display design 3-color LED (operating voltage, presence, error) Approvals FCC information Siemens SIMATIC RF210R (MLFB 6GT2821-1AC10) FCC ID NXW-RF210R This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. SIMATIC RF200 108 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.1 SIMATIC RF210R IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement. 5.1.8 Dimension drawing Figure 5-3 RF210R dimension drawing Dimensions in mm SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 109 Readers 5.2 SIMATIC RF210M 5.2 SIMATIC RF210M 5.2.1 Features SIMATIC RF210M 5.2.2 Characteristics Design ① RS422 interface ② Status display Application Reader for hand work and rework places, picking, track and trace, tool Ident Ordering data RF210M Article number RF210M with RS-422 interface (3964R) 6GT2823-0AA00 SIMATIC RF200 110 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.2 SIMATIC RF210M 5.2.3 Installing the RF210M reader The following figure shows the completely mounted reader. Note that you can mount the suspension bracket at two different points ①. If you do not mount the handle, we recommend that you close the opening ② with the protective cap. ① ② Holes for mounting the suspension bracket Thread for mounting the handle Figure 5-4 Installing the reader SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 111 Readers 5.2 SIMATIC RF210M 5.2.4 Pin assignment RF210M with RS-422 interface Pin Pin Assignment Device end 8-pin M12 5.2.5 + 24 V - Transmit 0V + Transmit + Receive - Receive Unassigned Ground (shield) LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 3 LED LED operating display on the reader Meaning The reader is turned off. Operating voltage present, reader not initialized or antenna switched off Operating voltage present, reader initialized and antenna switched on • Operating mode "with presence": Transponder present • Operating mode "without presence": Transponder present and command currently being executed There is an error. The number of flashes provides information about the current error. You can find more information on error messages in the section "Error codes of the RF200 readers (Page 329)". The optical error display is only reset if the corresponding reset parameter ("option_1 = 2") is set (see product information "SIMATIC RF200 Command Set (https://support.industry.siemens.com/cs/ww/en/view/44864850)"). SIMATIC RF200 112 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.2 SIMATIC RF210M 5.2.6 Technical specifications of the RF210M reader Table 5- 4 Technical specifications of the RF210M reader 6GT2823-0AA00 Product type designation SIMATIC RF210M Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 20 mm Maximum data transmission speed reader ↔ transponder ISO tags • Read • approx. 1500 bytes/s • Write • approx. 1500 bytes/s Typical transmission time for user data per byte • for write access • 0.6 ms • for read access • 0.6 ms Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader see section "Field data (Page 39)" MTBF (Mean Time Between Failures) 505 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication RS-422 Antenna integrated Mechanical specifications Housing • Material • POM • Color • Black Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 50 mA Permitted ambient conditions Ambient temperature • During operation • -20 … +50 °C • During transportation and storage • -25 … +60 °C SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 113 Readers 5.2 SIMATIC RF210M 6GT2823-0AA00 Degree of protection to EN 60529 IP54 Shock-resistant to EN 60721-3-7, Class 7 M3 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M3 200 m/s2 Design, dimensions and weight Dimensions 5.2.7 • Reader with handle (L x W x H) 195 x 26 x 140 mm • Reader without handle (L x W x H) 195 x 26 x 46 mm • Spiral connecting cable (L) 2m maximum working length 3.5 m Weight 460 g Type of mounting Bracket for for hanging up Cable length for RS-422 interface, maximum 1000 m LED display design 3-color LED (operating voltage, presence, error) Approvals FCC information Siemens SIMATIC RF210R (MLFB 6GT2821-1AC10) FCC ID NXW-RF210R This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. SIMATIC RF200 114 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.2 SIMATIC RF210M IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement. 5.2.8 Dimension drawing Figure 5-5 Dimension drawing RF210M All dimensions in mm, tolerances ± 1 mm SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 115 Readers 5.3 SIMATIC RF220R 5.3 SIMATIC RF220R 5.3.1 Features SIMATIC RF220R 5.3.2 Characteristics Design ① RS422 interface ② Status display Application Identification tasks on assembly lines in harsh industrial environments RF220R ordering data Article number RF220R with RS-422 interface (3964R) 6GT2821-2AC10 SIMATIC RF200 116 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.3 SIMATIC RF220R 5.3.3 RF220R pin assignment with RS422 interface Pin Pin Assignment Device end 8pin M12 5.3.4 + 24 V - Transmit 0V + Transmit + Receive - Receive Unassigned Ground (shield) LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 5 LED LED operating display on the reader Meaning The reader is turned off. Operating voltage present, reader not initialized or antenna switched off Operating voltage present, reader initialized and antenna switched on • Operating mode "with presence": Transponder present • Operating mode "without presence": Transponder present and command currently being executed There is an error. The number of flashes provides information about the current error. You can find more information on error messages in the section "Error codes of the RF200 readers (Page 329)". The optical error display is only reset if the corresponding reset parameter ("option_1 = 2") is set (see product information "SIMATIC RF200 Command Set (https://support.industry.siemens.com/cs/ww/en/view/44864850)"). SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 117 Readers 5.3 SIMATIC RF220R 5.3.5 Minimum distance between RF220R readers RF220R side by side ≥ 100 mm Figure 5-6 Minimum distance between RF220R readers RF220R face to face ≥ 150 mm Figure 5-7 Face-to-face distance between two RF220Rs SIMATIC RF200 118 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.3 SIMATIC RF220R 5.3.6 Technical specifications of the RF220R reader Table 5- 6 Technical specifications of the RF220R reader 6GT2821-2AC10 Product type designation SIMATIC RF220R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 35 mm Maximum data transmission speed reader ↔ transponder ISO tags • Read • approx. 1500 bytes/s • Write • approx. 1500 bytes/s Typical transmission time for user data per byte • for write access • 0.6 ms • for read access • 0.6 ms Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader see section "Field data (Page 39)" MTBF (Mean Time Between Failures) 501 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication RS-422 Antenna integrated Mechanical specifications Housing • Material • Brass, nickel-plated • Color • Silver Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 50 mA Permitted ambient conditions Ambient temperature • During operation • -20 … +70 °C SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 119 Readers 5.3 SIMATIC RF220R 6GT2821-2AC10 • During transportation and storage • -25 … +85 °C Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M3 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weight 5.3.7 Dimensions (∅ x thread x L) M30 x 1.5 x 83 mm Weight 140 g Type of mounting 2x nuts M30 x 1.5 Cable length for RS-422 interface, maximum 1000 m LED display design 3-color LED (operating voltage, presence, error) Approvals FCC information Siemens SIMATIC RF220R (MLFB 6GT2821-2AC10) FCC ID NXW-RF220R This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. SIMATIC RF200 120 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.3 SIMATIC RF220R IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement. 5.3.8 Dimension drawing Figure 5-8 RF220R dimension drawing Dimensions in mm SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 121 Readers 5.4 SIMATIC RF240R 5.4 SIMATIC RF240R 5.4.1 Features SIMATIC RF240R 5.4.2 Characteristics Structure ① RS-422 or RS-232 interface ② Operating indicator Field of application Identification tasks on assembly lines in harsh industrial environments RF240R ordering data Article number RF240R with RS-422 interface (3964R) 6GT2821-4AC10 RF240R with RS-232 interface (3964R) 6GT2821-4AC11 RF240R with RS-232 interface (ASCII) 6GT2821-4AC40 SIMATIC RF200 122 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.4 SIMATIC RF240R 5.4.3 Pin assignment RF240R Pin Pin Interface assignment Device end 8pin M12 RS-422 RS-232 +24 V +24 V - Transmit RXD 0V 0V + Transmit TXD + Receive Unassigned - Receive Unassigned Unassigned Unassigned Ground (shield) Ground (shield) 5.4.4 LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 7 LED LED operating display on the reader Meaning The reader is turned off. Operating voltage present, reader not initialized or antenna switched off Operating voltage present, reader initialized and antenna switched on • Operating mode "with presence": Transponder present • Operating mode "without presence": Transponder present and command currently being executed There is an error. The number of flashes provides information about the current error. You can find more information on error messages in the section "Error codes of the RF200 readers (Page 329)". The optical error display is only reset if the corresponding reset parameter ("option_1 = 2") is set (see product information "SIMATIC RF200 Command Set (https://support.industry.siemens.com/cs/ww/en/view/44864850)"). SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 123 Readers 5.4 SIMATIC RF240R 5.4.5 Minimum distance between several RF240R readers RF240R readers side by side ≥ 120 mm (with 2 readers) ≥ 200 mm (with more than 2 readers) Figure 5-9 Minimum distance between several RF240R readers RF240R face-to-face ≥ 400 mm Figure 5-10 Face-of-face distance between two RF240R readers SIMATIC RF200 124 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.4 SIMATIC RF240R 5.4.6 Technical specifications of the RF240R reader Table 5- 8 Technical specifications of the RF240R reader 6GT2821-4AC10 6GT2821-4AC11 6GT2821-4AC40 Product type designation SIMATIC RF240R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 65 mm Maximum data transmission speed reader ↔ transponder ISO tags • Read • approx. 1500 bytes/s • Write • approx. 1500 bytes/s Typical transmission time for user data per byte • for write access • 0.6 ms • for read access • 0.6 ms Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader see section "Field data (Page 39)" MTBF (Mean Time Between Failures) 430 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication • 6GT2821-4AC10 • RS-422 (3964R protocol) • 6GT2821-4AC11 • RS-232 (3964R protocol) • 6GT2821-4AC40 • RS-232 (ASCII protocol) Antenna integrated Mechanical specifications Housing • Material • Plastic PA 6.6 • Color • Anthracite Recommended distance to metal 0 mm SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 125 Readers 5.4 SIMATIC RF240R 6GT2821-4AC10 6GT2821-4AC11 6GT2821-4AC40 Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 25 mA Permitted ambient conditions Ambient temperature • During operation • -20 … +70 °C • During transportation and storage • -25 … +85 °C Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M3 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weight Dimensions (L x W x H) 50 × 50 × 30 mm Weight 60 g Type of mounting 2 x M5 screw 1.5 Nm Cable length, maximum • RS-422: max. 1000 m • RS-232: max. 30 m LED display design 3-color LED (operating voltage, presence, error) SIMATIC RF200 126 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.4 SIMATIC RF240R 5.4.7 Approvals FCC information Siemens SIMATIC RF240R (MLFB 6GT2821-4AC10) FCC ID NXW-RF240R Siemens SIMATIC RF240R (MLFB 6GT2821-4AC11) FCC ID NXW-RF240R Siemens SIMATIC RF240R (MLFB 6GT2821-4AC40) FCC ID NXW-RF240R This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 127 Readers 5.5 SIMATIC RF250R 5.4.8 Dimension drawing Figure 5-11 Dimension drawing RF240R Dimensions in mm 5.5 SIMATIC RF250R 5.5.1 Features SIMATIC RF250R Characteristics Structure ① RS-422 or RS-232 interface ② Operating indicator ③ Antenna connector, M8 Area of application Identification tasks on assembly lines in harsh industrial environments SIMATIC RF200 128 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.5 SIMATIC RF250R Note Reader requires external antennas Note that the RF250R reader is designed only for operation with external antennas and can only be operated in conjunction with the antennas ANT 3, ANT 8, ANT 12, ANT 18 or ANT 30. 5.5.2 Ordering data RF250R Article number 5.5.3 RF250R with RS-422 interface (3964R) 6GT2821-5AC10 RF250R with RS-232 interface (ASCII) 6GT2821-5AC40 Pin assignment RF250R Pin Pin Interface assignment Device end 8pin M12 5.5.4 RS-422 RS-232 +24 V +24 V - Transmit RXD 0V 0V + Transmit TXD + Receive Unassigned - Receive Unassigned Unassigned Unassigned Ground (shield) Ground (shield) LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 9 LED LED operating display on the reader Meaning The reader is turned off. Operating voltage present, reader not initialized or antenna switched off Operating voltage present, reader initialized and antenna switched on SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 129 Readers 5.5 SIMATIC RF250R LED Meaning • Operating mode "with presence": Transponder present • Operating mode "without presence": Transponder present and command currently being executed There is an error. The number of flashes provides information about the current error. You can find more information on error messages in the section "Error codes of the RF200 readers (Page 329)". The optical error display is only reset if the corresponding reset parameter ("option_1 = 2") is set (see product information "SIMATIC RF200 Command Set (https://support.industry.siemens.com/cs/ww/en/view/44864850)"). 5.5.5 Technical specifications of the RF250R reader Table 5- 10 Technical specifications of the RF250R reader 6GT2821-5AC10 6GT2821-5AC40 Product type designation SIMATIC RF250R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 35 mm Maximum data transmission speed reader ↔ transponder ISO tags • Read • approx. 1500 bytes/s • Write • approx. 1500 bytes/s Typical transmission time for user data per byte • for write access • 0.6 or 1.2 ms • for read access • 0.6 or 1.2 ms Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader see section "Field data (Page 39)" MTBF (Mean Time Between Failures) 430 years Interfaces Electrical connector design M8, 4-pin Standard for interfaces for communication • RS-422 • 3964R protocol • RS-232 • ASCII protocol SIMATIC RF200 130 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.5 SIMATIC RF250R 6GT2821-5AC10 6GT2821-5AC40 Antenna external, ANT 8, ANT 12, ANT 18, ANT 30 can be connected Mechanical specifications Housing • Material • Plastic PA 6.6 • Color • Anthracite Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 50 mA Permitted ambient conditions Ambient temperature • During operation • -20 … +70 °C • During transportation and storage • -25 … +85 °C Degree of protection to EN 60529 IP65 Shock-resistant to EN 60721-3-7, Class 7 M3 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M3 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weight Dimensions (L x W x H) 50 × 50 × 30 mm Weight 60 g Type of mounting 2 x M5 screw 1.5 Nm Cable length, maximum • RS-422: max. 1000 m • RS-232: max. 30 m LED display design 5.5.6 3-color LED Approvals FCC information Siemens SIMATIC RF250R (MLFB 6GT2821-5AC10) FCC ID NXW-RF250R Siemens SIMATIC RF250R (MLFB 6GT2821-5AC40) FCC ID NXW-RF250R SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 131 Readers 5.5 SIMATIC RF250R This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement. If the antenna is detachable, require the following two conditions: (1) To reduce potential radio interference to other users, the antenna type should be chosen that the radiated power is not more than that permitted for successful communication. (2) This device has been designed to operate with the antennas listed below. Antennas not included in this list are strictly prohibited for use with this device. The required antenna impedance is 50 Ω. Si l'antenne est amovible, demandez les deux conditions suivantes : (1) Afin de réduire le risque d'interférence aux autres utilisateurs, il faut choisir le type d'antenne et son gain de façon à ce que la puissance rayonnée ne soit pas supérieure au niveau requis pour l'obtention d'une communication satisfaisante. SIMATIC RF200 132 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.5 SIMATIC RF250R (2) Ce dispositif a été conçu pour fonctionner avec les antennes énumérées ci-dessous. Les antennes non incluses dans cette liste sont strictement interdites pour l'exploitation de ce dispositif. L'impéance d'antenne requise est 50 Ω. 5.5.7 Dimension drawing Figure 5-12 Dimension drawing RF250R Dimensions in mm SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 133 Readers 5.6 SIMATIC RF260R 5.6 SIMATIC RF260R 5.6.1 Features SIMATIC RF260R 5.6.2 Characteristics Structure ① RS-422 or RS-232 interface ② Operating indicator Field of application Identification tasks on assembly lines in harsh industrial environments Ordering data for RF260R Article number RF260R with RS-422 interface (3964R) 6GT2821-6AC10 RF260R with RS-232 interface (3964R) 6GT2821-6AC11 RF260R with RS-232 interface (ASCII) 6GT2821-6AC40 SIMATIC RF200 134 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.6 SIMATIC RF260R 5.6.3 Pin assignment RF260R Pin Pin Interface assignment Device end 8pin M12 RS-422 RS-232 +24 V +24 V - Transmit RXD 0V 0V + Transmit TXD + Receive Unassigned - Receive Unassigned Unassigned Unassigned Ground (shield) Ground (shield) 5.6.4 LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 11 LED LED operating display on the reader Meaning The reader is turned off. Operating voltage present, reader not initialized or antenna switched off Operating voltage present, reader initialized and antenna switched on • Operating mode "with presence": Transponder present • Operating mode "without presence": Transponder present and command currently being executed There is an error. The number of flashes provides information about the current error. You can find more information on error messages in the section "Error codes of the RF200 readers (Page 329)". The optical error display is only reset if the corresponding reset parameter ("option_1 = 2") is set (see product information "SIMATIC RF200 Command Set (https://support.industry.siemens.com/cs/ww/en/view/44864850)"). SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 135 Readers 5.6 SIMATIC RF260R 5.6.5 Minimum distance between several RF260R RF260R side by side ≥ 150 mm (with 2 readers) ≥ 250 mm (with more than 2 readers) Figure 5-13 Minimum distance between several RF260R RF260R face to face ≥ 500 mm Figure 5-14 Face-to-face distance between two RF260R SIMATIC RF200 136 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.6 SIMATIC RF260R 5.6.6 Technical data of the RF260R reader Table 5- 12 Technical specifications of the RF260R reader 6GT2821-6AC10 6GT2821-6AC11 6GT2821-6AC40 Product type designation SIMATIC RF260R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 135 mm Maximum data transmission speed reader ↔ transponder ISO tags • Read • approx. 1500 bytes/s • Write • approx. 1500 bytes/s Typical transmission time for user data per byte • for write access • 0.6 ms • for read access • 0.6 ms Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader see section "Field data (Page 39)" MTBF (Mean Time Between Failures) 480 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication • 6GT2821-6AC10 • RS-422 (3964R protocol) • 6GT2821-6AC11 • RS-232 (3964R protocol) • 6GT2821-6AC40 • RS-232 (ASCII protocol) Antenna integrated Mechanical specifications Housing • Material • Plastic PA 6.6 • Color • Anthracite Recommended distance to metal 0 mm Supply voltage, current consumption, power loss SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 137 Readers 5.6 SIMATIC RF260R 6GT2821-6AC10 6GT2821-6AC11 6GT2821-6AC40 Supply voltage 24 VDC Typical current consumption 50 mA Permitted ambient conditions Ambient temperature • During operation • -20 … +70 °C • During transportation and storage • -25 … +80 °C Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M3 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weight Dimensions (L x W x H) 75 × 75 × 41 mm Weight 200 g Type of mounting 2 x M5 screw 1.5 Nm Cable length, maximum • RS-422: max. 1000 m • RS-232: max. 30 m LED display design 5.6.7 3-color LED (operating voltage, presence, error) Approvals FCC information Siemens SIMATIC RF260R (MLFB 6GT2821-6AC10) FCC ID NXW-RF260R Siemens SIMATIC RF260R (MLFB 6GT2821-6AC11) FCC ID NXW-RF260R Siemens SIMATIC RF260R (MLFB 6GT2821-6AC40) FCC ID NXW-RF260R This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. SIMATIC RF200 138 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.6 SIMATIC RF260R Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement. 5.6.8 Dimension drawing Figure 5-15 Dimension drawing RF260R Dimensions in mm SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 139 Readers 5.7 SIMATIC RF280R 5.7 SIMATIC RF280R 5.7.1 Features SIMATIC RF280R 5.7.2 Characteristics Structure ① RS-422 or RS-232 interface ② Operating indicator Field of application Identification tasks on assembly lines in harsh industrial environments Ordering data RF280R Article number RF280R with RS422 interface (3964R) 6GT2821-8AC10 RF280R with RS232 interface (ASCII) 6GT2821-8AC40 SIMATIC RF200 140 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.7 SIMATIC RF280R 5.7.3 Pin assignment RF280R Pin Pin Interface assignment Device end 8pin M12 RS-422 RS-232 +24 V +24 V - Transmit RXD 0V 0V + Transmit TXD + Receive Unassigned - Receive Unassigned Unassigned Unassigned Ground (shield) Ground (shield) 5.7.4 LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 13 LED LED operating display on the reader Meaning The reader is turned off. Operating voltage present, reader not initialized or antenna switched off Operating voltage present, reader initialized and antenna switched on • Operating mode "with presence": Transponder present • Operating mode "without presence": Transponder present and command currently being executed There is an error. The number of flashes provides information about the current error. You can find more information on error messages in the section "Error codes of the RF200 readers (Page 329)". The optical error display is only reset if the corresponding reset parameter ("option_1 = 2") is set (see product information "SIMATIC RF200 Command Set (https://support.industry.siemens.com/cs/ww/en/view/44864850)"). SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 141 Readers 5.7 SIMATIC RF280R 5.7.5 Minimum distance between RF280R readers RF280R side-by-side ≥ 150 mm (with 2 readers) ≥ 250 mm (with more than 2 readers) Figure 5-16 Minimum distance between RF280R readers RF280R Face-to-Face ≥ 800 mm Figure 5-17 Face-to-face distance between two RF280R SIMATIC RF200 142 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.7 SIMATIC RF280R 5.7.6 Technical specifications of the RF280R reader Table 5- 14 Technical specifications of the RF280R reader 6GT2821-8AC10 6GT2821-8AC40 Product type designation SIMATIC RF280R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 200 mm Maximum data transmission speed reader ↔ transponder ISO transponder • Read • approx. 1500 bytes/s • Write • approx. 1500 bytes/s Typical transmission time for user data per byte • for write access • 0.6 ms • for read access • 0.6 ms Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader see section "Field data (Page 39)" MTBF (Mean Time Between Failures) 172.6 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication • 6GT2821-6AC10 • RS-422 (3964R protocol) • 6GT2821-6AC40 • RS-232 (ASCII protocol) Antenna integrated Mechanical specifications Housing • Material • Plastic PA 12 • Color • TI grey Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 130 mA SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 143 Readers 5.7 SIMATIC RF280R 6GT2821-8AC10 6GT2821-8AC40 Permitted ambient conditions Ambient temperature • During operation • -25 … +70 °C • During transportation and storage • -40 … +85 °C Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M3 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weight Dimensions (L x W x H) 160 x 80 x 41 mm Weight 470 g Type of mounting 4x screws M5 ≤ 1.5 Nm Cable length, maximum • RS-422: max. 1000 m • RS-232: max. 30 m LED display design 3-color LED (operating voltage, presence, error) Standards, specifications, approvals Proof of suitability 5.7.7 Radio according to R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA Approvals FCC information Siemens SIMATIC RF280R (MLFB 6GT2821-8AC10) FCC ID NXW-RF280R Siemens SIMATIC RF280R (MLFB 6GT2821-8AC40) FCC ID NXW-RF280R This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. SIMATIC RF200 144 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.7 SIMATIC RF280R Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 145 Readers 5.7 SIMATIC RF280R 5.7.8 Dimension drawing Figure 5-18 Dimensional drawing of RF280R Dimensions in mm SIMATIC RF200 146 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.8 SIMATIC RF290R 5.8 SIMATIC RF290R 5.8.1 Features SIMATIC RF290R Characteristics Design Application ① RS-422/RS-232 interface, 24 V power supply ② Digital I/O ③ External antenna ④ Operating display, 4 LEDs: • Power (PWR) • Active (ACT) • Present (PRE) • Error (ERR) Identification tasks in production control and in intra-logistics, e.g. skid identification, container management, HF gates (F&B) When connected via a PC multitag operation is possible. Note Reader requires external antennas Note that the RF290R reader is designed only for operation with external antennas and can only be operated in conjunction with the antennas ANT D5, D6 or D10. Note Note on operating the reader with ANT D6 / D10 When operating with a power ≥ 3 W, the limits are adhered to according to 2004/40/EC (minimum requirements concerning the protection of workers). Note that the antennas may only be used in an "industrial environment" and not in buildings used by the public. 5.8.2 Ordering data RF290R Table 5- 15 Ordering data RF290R Article number RF290R with RS-232 interface for PC mode and RS-422 interface for CM mode 6GT2821-0AC12 SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 147 Readers 5.8 SIMATIC RF290R Table 5- 16 Ordering data - accessories - RF290R Article number 24 V connecting cable 5m 6GT2491-1HH50 RS-232 connecting cable, with 4-pin M12 connector for 24 V for connection to the wide-range power supply unit 5m 6GT2891-4KH50 RS-232 connecting cable with open cable ends for 24 V 5m 6GT2891-4KH50-0AX0 Adapter for mounting on a DIN rail (pack of 3) 6GK5798-8ML00-0AB3 Wide-range power supply unit for SIMATIC RF-systems (100 - 240 VAC / 24 VDC / 3 A) with 2 m connecting cable with country-specific plug EU: 6GT2898-0AA00 UK: 6GT2898-0AA10 US: 6GT2898-0AA20 Connecting cables Reader ↔ ASM 475 2m 6GT2891-4EH20 5m 6GT2891-4EH50 Reader ↔ CM/ASM 2m 6GT2891-4FH20 for RF200 / RF300 / RF600 / MV400 or extension cable MOBY U/D 5m 6GT2891-4FH50 10 m 6GT2891-4FN10 20 m 6GT2891-4FN20 50 m 6GT2891-4FN50 Connecting / extension cable Antennas Antenna ANT D5 6GT2698-5AA10 Antenna ANT D6 6GT2698-5AB00 Covering hood for ANT D6 6GT2690-0AD00 Antenna ANT D10 6GT2698-5AF00 Accessories for connecting multiple antennas to SIMATIC RF290R Antenna multiplexer 6GT2894-0EA00 incl. one antenna connecting cable 0.4 m Antenna splitter 6GT2690-0AC00 incl. one antenna connecting cable 3.3 m Antenna cables Antenna cable Antenna cable extension 3.3 m 6GT2691-0CH33 10.5 m 6GT2691-0CN10 7.2 m 6GT2691-0DH72 SIMATIC RF200 148 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.8 SIMATIC RF290R 5.8.3 Pin assignment RF290R RS422/RS232 Table 5- 17 Pin Pin assignment of the RS-422/RS 232 interface Pin Interface assignment Device end 8pin M12 RS-422 RS-232 +24 V +24 V - Transmit RXD 0V 0V + Transmit TXD + Receive not used - Receive not used not used not used Ground (shield) Ground (shield) Digital I/O only possible in PC mode (RS-232) Table 5- 18 Pin Pin assignment of the digital I/O interface Pin Socket assignment Device end 4pin M12 Figure 5-19 DO - relay contact COM (Common) DO - relay contact NO (Normaly Open, NO contact) DI - switched input, +24 V DI - ground, 0 V Pin assignment of the power supply connector SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 149 Readers 5.8 SIMATIC RF290R Digital input (DI): The opto-coupler input is electrically isolated from the reader electronics. The external 24 V must be connected to the DI according to the circuit diagram. Make sure that the polarity of the 24 V is correct. The current is limited to < 10 mA by the integrated resistor. NOTICE Reader may be damaged If you exceed the maximum permitted supply voltage, the reader may be damaged. Make sure that the input voltage does not exceed the maximum permitted supply voltage of the reader. Digital output (DO): At the relay output, a NO contact is available. The output is electrically isolated from the reader electronics and therefore needs to be supplied externally. NOTICE Reader may be damaged If you exceed the maximum permitted voltage of 24 V / 1 A at the relay output, the reader may be damaged. Make sure that the voltage does not exceed 24 V. The output is intended only for switching resistive loads. If it is used to switch inductive loads, the reader may be damaged. Make sure that if inductive loads occur, the relay contacts are protected by an external suppressor circuit. SIMATIC RF200 150 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.8 SIMATIC RF290R 5.8.4 LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 19 Labeling LED operating display on the reader LED Meaning The reader is turned off. PWR CM mode: Operating voltage present, reader not initialized or antenna switched off CM mode: Operating voltage present, reader initialized and antenna switched on PC mode: Supply voltage is on ACT Communication on the data line PRE • Operating mode "with presence": Transponder present • Operating mode "without presence": Transponder present and command currently being executed ERR CM mode: There is an error. The number of flashes provides information about the current error. You can find more information on error messages in the section "Error codes of the RF200 readers (Page 329)". The optical error display is only reset if the corresponding reset parameter ("option_1 = 2") is set (see Product Information " Product information "SIMATIC RF200 command set" (https://support.industry.siemens.com/cs/ww/en/view/44864850 )"). PC mode: Error when connecting the antenna or the interference level in the antenna environment is too high SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 151 Readers 5.8 SIMATIC RF290R 5.8.5 Installing the RF290R reader 5.8.5.1 Wall mounting Use the holes in the housing to screw the device to the wall or onto a horizontal surface. The position of the drill holes is shown in the following figure: Figure 5-20 Drilling pattern for the RF290R (dimensions in mm) A: M4 threaded socket for potential connection of the reader. You will find further information on the potential connection in the section "Further information (Page 101)". SIMATIC RF200 152 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.8 SIMATIC RF290R 5.8.5.2 Installing on the S7-300 standard rail Follow the steps below to mount the RF290R reader on a vertical S7-300 standard rail: 1. Place the device on the upper edge of the S7-300 standard rail (position A). 2. Screw the device to the mounting rail (position B). Figure 5-21 5.8.5.3 Installing the RF290R reader on the S7-300 standard rail Installation on a DIN rail The RF290R reader is suitable for installation on 35 mm rails that comply with DIN EN 50022. Note The adapter for mounting on a DIN rail does not ship with the RF290R The adapter for mounting on a DIN rail does not ship with the product. You can obtain a pack of three with the following article number: 6GK5798-8ML00-0AB3. The mounting fittings consist of the following parts: • 1 DIN rail slider • 1 spring • 2 screws Fit the adapter to the rear of the device as shown in the following figure: SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 153 Readers 5.8 SIMATIC RF290R Figure 5-22 Mounting the DIN rail adapter Follow the steps below to mount the RF290R reader on a DIN rail: 1. Place the device on the upper edge of the DIN rail (position A). 2. Pull the spring-mounted DIN rail slider (position B) down and press the device against the DIN rail until it locks in place. Figure 5-23 Mounting the RF290R reader on a DIN rail SIMATIC RF200 154 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.8 SIMATIC RF290R 5.8.6 Technical specifications of the RF290R reader Table 5- 20 Technical specifications of the RF290R reader 6GT2821-0AC12 Product type designation SIMATIC RF290R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 65 mm Maximum data transmission speed reader ↔ transponder ISO tags • Read • approx. 1500 bytes/s • Write • approx. 1500 bytes/s Typical transmission time for user data per byte • for write access • 0.6 ms • for read access • 0.6 ms Multitag capability When connected via a PC Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader see section "Field data (Page 39)" MTBF (Mean Time Between Failures) 18 years Interfaces Electrical connector design TNC Standard for interfaces for communication • RS-422 • RS-232 Antenna external, ANT D5, D6 or D10 can be connected Mechanical specifications Housing • Material • Aluminum die-casting • Color • Silver/anthracite Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC (± 10%) Typical current consumption 400 mA (at 24 V and 5 W) SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 155 Readers 5.8 SIMATIC RF290R 6GT2821-0AC12 Permitted ambient conditions Ambient temperature • During operation • -20 … +55 °C • During transportation and storage • -25 … +85 °C Degree of protection to EN 60529 IP65 Shock-resistant to EN 60721-3-7, Class 7 M3 300 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M3 20 m/s2 Torsion and bending load Not permitted Design, dimensions and weight Dimensions (W x H x D) 200 × 80 × 140 mm Weight 1.8 kg Type of mounting 2 x M5 screw 1.5 Nm Cable length, maximum • RS-422: max. 1000 m • RS-232: max. 30 m LED display design 5.8.7 4 LEDs Approvals FCC information Siemens SIMATIC RF290R (MLFB 6GT2821-0AC12) FCC ID NXW-RF290R This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. SIMATIC RF200 156 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.8 SIMATIC RF290R Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement. If the antenna is detachable, require the following two conditions: (1) To reduce potential radio interference to other users, the antenna type should be chosen that the radiated power is not more than that permitted for successful communication. (2) This device has been designed to operate with the antennas listed below. Antennas not included in this list are strictly prohibited for use with this device. The required antenna impedance is 50 Ω. Si l'antenne est amovible, demandez les deux conditions suivantes : (1) Afin de réduire le risque d'interférence aux autres utilisateurs, il faut choisir le type d'antenne et son gain de façon à ce que la puissance rayonnée ne soit pas supérieure au niveau requis pour l'obtention d'une communication satisfaisante. (2) Ce dispositif a été conçu pour fonctionner avec les antennes énumérées ci-dessous. Les antennes non incluses dans cette liste sont strictement interdites pour l'exploitation de ce dispositif. L'impéance d'antenne requise est 50 Ω. SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 157 Readers 5.8 SIMATIC RF290R 5.8.8 Note on the use of the RF290R as a replacement for SLG D10 / SLG D10S The RF290R reader is the successor to the MOBY D readers SLG D10 / SLG D10S rounding off the RF200 family; it is operated with external antennas. The following features distinguish the RF290R from the SLG models: Table 5- 21 Differences between the RF290R readers and SLG D10 / SLG D10S Properties SLG D10/SLG D10S Properties RF290R Two devices with different interfaces RS-232/RS-422 interface and PC/CM functionality in one device M 12, 4-pin male connector for the power supply 9-pin D-sub male connector for connection to the various communications modules M12, 8-pin male connector for the power supply and for direct connection to the various communications modules 1) no digital I/O M12, 4-pin female connector for digital I/O (can only be used in PC mode) no operating display via LEDs operating display by four LEDs Maximum transmit power of 10 W Maximum transmit power of 5 W One securing option Different securing options Standard protocol in ISO host mode (in PC mode) Advanced protocol in ISO host mode (in PC mode) 2) Amplitude Shift Keying (ASK) and Frequency Shift Keying (FSK) modes possible Amplitude Shift Keying (ASK) mode possible Support of "ICode1" and "TagIt" and ISO 15693compatible transponders Support of ISO 15693-compatible transponders The total memory for "repeat_command" is limited to 32 kB The total memory for "repeat_command" is limited to 16 kB 1) The RF290R reader connectors are compatible with the SLG D10 if a Y connecting cable is used (6GT2891-4KH50, 6GT2891-4KH50-0AX0). 2) In ISO host mode (in PC mode), a program adaptation is necessary SIMATIC RF200 158 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Readers 5.8 SIMATIC RF290R 5.8.9 Dimension drawing Figure 5-24 Dimensional drawing RF290R (dimensions in mm) SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 159 6 Antennas Note The RF250R and RF290R readers require external antennas Note that the RF250R and RF290R readers are designed for operation with external antennas. The RF250R reader can only be used in conjunction with the antennas ANT 3, 8, 12, 18 or 30. The RF290R reader can only be used in conjunction with the antennas ANT D5, D6 or D10. 6.1 ANT 1 6.1.1 Characteristics ANT 1 6.1.2 Characteristics Area of application Small assembly lines Read/write distance up to 140 mm (depending on the transponder) Connecting cable 3 m (plug-in antenna cable) Connectable readers RF250R Degree of protection IP67 Ordering data Table 6- 1 Ordering data ANT 1 Antenna Article number ANT 1 (including one plug-in antenna cable 3 m) 6GT2398-1CB00 Table 6- 2 Ordering data ANT 1 accessories Accessories Article number Antenna cable, 3 m 6GT2398-0AH30 SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 161 Antennas 6.1 ANT 1 6.1.3 Flush-mounted in metal The tuning of the ANT 1 antenna is optimized for mounting in metal. = 40 mm Figure 6-1 6.1.4 ANT 1 flush-mounted in metal Operating / limit distances The operating / limit distances listed in the following table relate to an ANT 1 mounted in metal. Table 6- 3 Operating / limit distances of the transponders RF250R with ANT 1 RF250R with ANT 1 Operating distance (Sa) Limit distance (Sg) MDS D100 5...110 140 MDS D124 2...65 85 MDS D126 2...90 120 MDS D139 5...85 115 MDS D160 2...35 60 MDS D165 5...100 120 MDS D200 5...95 115 MDS D261 5...80 95 MDS D324 2...66 78 MDS D339 5...90 105 MDS D400 2...110 135 MDS D423 10...40 50 MDS D424 2...75 88 MDS D425 2...25 35 MDS D426 2...85 95 MDS D428 2...40 50 SIMATIC RF200 162 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Antennas 6.1 ANT 1 RF250R with ANT 1 RF250R with ANT 1 Operating distance (Sa) Limit distance (Sg) MDS D460 2...32 38 MDS D524 2...65 85 MDS D525 2...25 35 MDS D526 2...85 105 MDS D528 2...35 50 All values are in mm 6.1.5 Minimum clearances Note Extension of the data transmission time if distance values are undershot If the distance values specified in the tables are undershot, it is possible that the inductive fields will be affected. In this case, the data transmission time can increase unpredictably or a command is aborted with an error. For this reason, please observe the values in the tables. Minimum distances from transponder to transponder (without multitag mode) Table 6- 4 Minimum distances transponder edge to transponder edge RF250R with ANT 1 MDS D423 / MDS D425 MDS D126 / MDS D160 / MDS D165 / MDS D200 / MDS D339 / MDS D426 / MDS D428 / MDS D460 MDS D100 / MDS D124 / MDS D139 / MDS D 261 / MDS D400 / MDS D424 ≥ 120 mm ≥ 150 mm ≥ 240 mm SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 163 Antennas 6.1 ANT 1 Minimum distances from antenna to antenna ≥ 300 mm Figure 6-2 ≥ 500 mm Figure 6-3 6.1.6 Minimum distance ANT 1 Face-to-face minimum distance ANT 1 Technical specifications 6GT2398-1CB00 Product type designation ANT 1 Electrical data Maximum write/read distance ANT ↔ Transponder (Sg) 140 mm Interfaces Plug connection M8, 4-pin; pins on antenna side SIMATIC RF200 164 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Antennas 6.1 ANT 1 6GT2398-1CB00 Mechanical specifications Housing • Material • Plastic PA 12 • Color • Anthracite MTBF 13698 years Permitted ambient conditions Ambient temperature • During operation • -25 ℃ ... +70 ℃ • During transportation and storage • -40 °C ... +85 °C Degree of protection to EN 60529 Shock according to EN 60721-3-7 Class 7 IP67 M31) 500 m/s2 Vibration according to EN 60721-3-7 Class 7 M31) 200 m/s2 Design, dimensions and weight Dimensions (L × W × H) 75 x 75 x 20 mm Weight 225 g Type of mounting 2 x M5 screws Cable length 3 m (plug-in antenna cable) 1) 6.1.7 Warning: The values for shock and vibration are maximum values and must not be applied continuously. Dimension drawing Figure 6-4 Dimensional drawing of ANT 1 (all values in mm) SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 165 Antennas 6.2 ANT 3 6.2 ANT 3 6.2.1 Features ANT 3 6.2.2 Characteristics Area of application Small assembly lines Writing/reading distance up to 50 mm (depending on the transponder) Connecting cable 3 m (plug-in antenna cable) Connectable readers RF250R Degree of protection IP67 Ordering data Table 6- 5 Ordering data ANT 3 Antenna Article number ANT 3 (without antenna cable) 6GT2398-1CD30-0AX0 ANT 3 (incl. one plug-in antenna cable 3 m) 6GT2398-1CD40-0AX0 Table 6- 6 Ordering data ANT 3 accessories Accessories Article number Antenna cable, 3 m 6GT2398-0AH30 SIMATIC RF200 166 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Antennas 6.2 ANT 3 6.2.3 Mounting on/in metal The tuning of the ANT 3 antenna is optimized for mounting on metal. ① ② ANT 3 Metal Figure 6-5 ① ② ANT 3 = 10 mm ANT 3 mounted on metal Metal Figure 6-6 ANT 3 flush-mounted in metal SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 167 Antennas 6.2 ANT 3 6.2.4 Operating / limit distances The operating / limit distances listed in the following table relate to an ANT 3 mounted on metal. Table 6- 7 Operating / limit distances of the transponders RF250R with ANT 3 RF250R with ANT 3 Operating distance (Sa) Limit distance (Sg) MDS D124 2 ... 32 40 MDS D160 1 ... 16 20 MDS D324 2 ... 32 40 MDS D422 1 ... 12 15 MDS D423 (without metal) 0 ... 20 25 MDS D423 (on metal) 0 ... 24 30 MDS D423 (in metal - 10 mm clearance all round) 0 ... 24 30 MDS D423 (in metal - 0 mm clearance all round) 0 ... 16 20 MDS D424 0 ... 45 50 MDS D425 0 ... 16 20 MDS D428 0 ... 25 32 MDS D460 0 ... 18 25 MDS D522 1 ... 12 15 MDS D522 Special variant 1 ... 12 15 MDS D524 1 ... 30 40 MDS D528 1 ... 20 25 All values are in mm SIMATIC RF200 168 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Antennas 6.2 ANT 3 6.2.5 Minimum spacing Note Extension of the data transmission time if distance values are undershot If the distance values specified in the tables are undershot, it is possible that the inductive fields will be affected. In this case, the data transmission time can increase unpredictably or a command is aborted with an error. For this reason, please observe the values in the tables. Minimum distances from transponder to transponder (without multitag mode) Table 6- 8 Minimum distances transponder edge to transponder edge RF250R with ANT 3 MDS D124 / MDS D160 / MDS D324 / MDS D423 / MDS D424 / MDS D428 / MDS D460 / MDS D524 / MDS D528 MDS D422 / MDS D425 / MDS D522 > 80 mm > 60 mm Minimum distances from antenna to antenna ≥ 150 mm Figure 6-7 Minimum distance for ANT 3 SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 169 Antennas 6.2 ANT 3 ≥ 200 mm Figure 6-8 6.2.6 Face-to-face distance between two ANT 3s Technical data 6GT2398-1CD30-0AX0 6GT2398-1CD40-0AX0 Product type designation ANT 3 Electrical data Maximum write/read distance ANT ↔ Transponder (Sg) 50 mm Interfaces Plug connection M8, 4-pin socket on antenna side (with antenna connecting cable: pin cable end) Mechanical specifications Housing • Material • Plastic PA6-V0 • Color • Black MTBF 13698 years Permitted ambient conditions Ambient temperature • During operation • -25 ℃ ... +70 ℃ • During transportation and storage • -40 °C ... +85 °C Degree of protection to EN 60529 IP67 Shock according to EN 60721-3-7 Class 7 M31) 500 m/s2 Vibration according to EN 60721-3-7 Class 7 M31) 200 m/s2 Design, dimensions and weight Dimensions (L × W × H) SIMATIC RF200 170 System Manual, 07/2017, J31069-D0227-U001-A9-7619 Antennas 6.2 ANT 3 6GT2398-1CD30-0AX0 6GT2398-1CD40-0AX0 • Housing without antenna connector • 50 × 28 × 10 mm • Housing with antenna connector • 240 × 28 × 10 mm Weight • Housing with antenna connector • Approx. 35 g • Housing with antenna connector and antenna cable • Approx. 160 g Type of mounting 2 x M4 screws Cable length 3 m (plug-in antenna cable) 1) 6.2.7 Warning: The values for shock and vibration are maximum values and must not be applied continuously. Dimension drawing Figure 6-9 Dimension drawing ANT 3 (all values in mm) SIMATIC RF200 System Manual, 07/2017, J31069-D0227-U001-A9-7619 171 Antennas 6.3 ANT 8 6.3 ANT 8 6.3.1 Features ANT 8 6.3.2 Characteristics Area of application Tool identification Writing/reading distance up to 4 mm (depending on the transponder) Connecting cable 3m Connectable readers RF250R Degree of protection IP67 Ordering data Table 6- 9 Ordering data ANT 8 Antenna Article number ANT 8 (without antenna cable) 6GT2398-1CF00 ANT 8 (including one plug-in antenna cable 3 m) 6GT2398-1CF10 Table 6- 10 Ordering data ANT 8 accessories Accessories Article number Antenna cable, 3 m 6GT2398-0AH30 SIMATIC RF200 172 System Manual, 07/2017, J31069-D0227-U001-A9-7619
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : Siemens AG Create Date : 2017:07:05 15:24:11+02:00 Modify Date : 2017:08:17 16:22:37+02:00 Subject : SIMATIC Ident Has XFA : No Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2017:08:17 16:22:37+02:00 Creator Tool : Acrobat PDFMaker 17 für Word Document ID : uuid:bbce7b7a-f188-413e-baf5-913b15b647bb Instance ID : uuid:e4b9c4f3-b784-4011-a723-5456a6eb8abf Format : application/pdf Title : SIMATIC RF200 Description : SIMATIC Ident Creator : Siemens AG Producer : Adobe PDF Library 15.0 Source Modified : D:20170705132114 Company : Siemens AG Comments : Edition : 0.00347050074367873 System : SIMATIC Ident Print-year : 2010 - 2017 Document-class : System Manual Document-class-mrl : Product-group : RFID systems Order-nr : J31069-D0227-U001-A9-7619 Company-short : Siemens Company-long : Siemens AG Page Layout : OneColumn Page Mode : UseOutlines Page Count : 172EXIF Metadata provided by EXIF.tools