Siemens RF340R01 Inductive Tag Reader User Manual SIMATIC RF300

Siemens AG Inductive Tag Reader SIMATIC RF300

User Manual I

Introduction 1 Safety information 2 System overview 3 RF300 system planning 4 Readers 5 RF300 transponder 6 ISO transponder 7 System integration 8 System diagnostics 9 Appendix A SIMATIC Sensors RFID systemsSIMATIC RF300 System Manual 11/2009 - Zwischenstand 17.09.2009A5E01642529-04
Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe personal injury will result if proper precautions are not taken. WARNING indicates that death or severe personal injury may result if proper precautions are not taken. CAUTION with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken. CAUTION without a safety alert symbol, indicates that property damage can result if proper precautions are not taken. NOTICE indicates that an unintended result or situation can occur if the corresponding information is not taken into account. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage. Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation for the specific task, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems. Proper use of Siemens products Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be adhered to. The information in the relevant documentation must be observed. Trademarks All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. Siemens AG Industry Sector Postfach 48 48 90026 NÜRNBERG GERMANY A5E01642529-04 Ⓟ 11/2009 Copyright © Siemens AG . Technical data subject to change
SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 5 Table of contents 1 Introduction.............................................................................................................................................. 11 1.1 Navigating in the system manual.................................................................................................11 1.2 Preface.........................................................................................................................................11 2 Safety information.................................................................................................................................... 13 3 System overview...................................................................................................................................... 15 3.1 RFID systems...............................................................................................................................15 3.2 SIMATIC RF300...........................................................................................................................15 3.2.1 RF300 system overview...............................................................................................................15 3.2.2 RFID components and their function ...........................................................................................17 3.2.3 Application areas of RF300..........................................................................................................20 3.3 System configuration ...................................................................................................................21 3.3.1 Overview ......................................................................................................................................21 3.3.2 Assembly line example: Use of RF300 tags................................................................................21 3.3.3 Example of container and paper board container handling: Use of ISO tags .............................23 3.4 System data .................................................................................................................................25 4 RF300 system planning ........................................................................................................................... 27 4.1 Fundamentals of application planning .........................................................................................27 4.1.1 Selection criteria for SIMATIC RF300 components.....................................................................27 4.1.2 Transmission window and read/write distance ............................................................................27 4.1.3 Width of the transmission window................................................................................................32 4.1.4 Impact of secondary fields ...........................................................................................................32 4.1.5 Permissible directions of motion of the transponder....................................................................35 4.1.6 Operation in static and dynamic mode ........................................................................................35 4.1.7 Dwell time of the transponder ......................................................................................................36 4.1.8 Communication between communication module, reader and transponder ...............................37 4.1.9 Calculation example (RS422) ......................................................................................................39 4.2 Field data for transponders, readers and antennas.....................................................................41 4.2.1 Field data of RF300 transponders ...............................................................................................41 4.2.2 Field data of ISO transponders....................................................................................................44 4.2.3 Minimum clearances ....................................................................................................................47 4.3 Dependence of the volume of data on the transponder speed with RF300 tags ........................49 4.3.1 RF320T with RF310R, RF340R, RF350R, RF380R....................................................................49 4.3.2 RF340T with RF310R, RF340R, RF350R, RF380R....................................................................49 4.3.3 RF350T with RF310R, RF340R, RF350R, RF380R....................................................................50 4.3.4 RF360T with RF310R, RF340R, RF350R, RF380R....................................................................51 4.3.5 RF370T with RF340R, RF350R, RF380R ...................................................................................52 4.3.6 RF380T with RF340R, RF350R, RF380R ...................................................................................53 4.4 Dependence of the volume of data on the transponder speed with ISO tags.............................54 4.4.1 MDS D100 with RF310R, RF340R/RF350R and RF380R ..........................................................54 4.4.2 MDS D124 with RF310R, RF340R/RF350R and RF380R ..........................................................55 4.4.3 MDS D139 with RF310R, RF340R/RF350R and RF380R ..........................................................56 4.4.4 MDS D160 with RF310R, RF340R/RF350R and RF380R ..........................................................57
Table of contents SIMATIC RF300 6 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 4.4.5 MDS D324 with RF310R and RF380R ....................................................................................... 58 4.4.6 MDS D424 with RF310R, RF340R/RF350R and RF380R ......................................................... 59 4.4.7 MDS D428 with RF310R, RF340R/RF350R and RF380R ......................................................... 60 4.4.8 MDS D460 with RF310R, RF340R/RF350R and RF380R ......................................................... 61 4.5 Installation guidelines.................................................................................................................. 62 4.5.1 Overview ..................................................................................................................................... 62 4.5.2 Reduction of interference due to metal ....................................................................................... 63 4.5.3 Effects of metal on different transponders and readers.............................................................. 65 4.5.4 Impact on the transmission window by metal ............................................................................. 66 4.5.4.1 Impact on the transmission window by metal ............................................................................. 66 4.5.4.2 RF310R....................................................................................................................................... 66 4.5.4.3 RF340R....................................................................................................................................... 68 4.5.4.4 RF350R....................................................................................................................................... 70 4.5.4.5 RF380R....................................................................................................................................... 75 4.6 Chemical resistance of the transponders.................................................................................... 77 4.6.1 Chemical resistance of the RF300 transponders........................................................................ 77 4.6.2 Chemical resistance of the ISO transponders ............................................................................ 82 4.7 EMC Directives ........................................................................................................................... 86 4.7.1 Overview ..................................................................................................................................... 86 4.7.2 What does EMC mean?.............................................................................................................. 87 4.7.3 Basic rules................................................................................................................................... 88 4.7.4 Propagation of electromagnetic interference .............................................................................. 89 4.7.5 Cabinet configuration .................................................................................................................. 92 4.7.6 Prevention of interference sources .............................................................................................94 4.7.7 Equipotential bonding.................................................................................................................. 95 4.7.8 Cable shielding............................................................................................................................ 96 5 Readers................................................................................................................................................... 99 5.2 SIMATIC RF310R with IQ-Sense interface............................................................................... 100 5.2.1 Features .................................................................................................................................... 100 5.2.2 Ordering data of RF310R with IQ-Sense interface ................................................................... 100 5.2.3 Pin assignment of RF310R IQ-Sense interface........................................................................ 100 5.2.4 Display elements of the RF310R reader with IQ-Sense interface ............................................ 101 5.2.5 Ensuring reliable data exchange............................................................................................... 101 5.2.6 Metal-free area.......................................................................................................................... 101 5.2.7 Minimum distance between RF310R readers........................................................................... 102 5.2.8 Technical data for RF310R reader with IQ-Sense interface..................................................... 102 5.2.9 FCC information ........................................................................................................................ 103 5.2.10 Dimension drawing.................................................................................................................... 104 5.3 SIMATIC RF310R with RS422 interface................................................................................... 104 5.3.1 Features .................................................................................................................................... 104 5.3.2 Ordering data for RF310R with RS422 interface ...................................................................... 105 5.3.3 Pin assignment of RF310R RS422 interface ............................................................................ 105 5.3.4 Display elements of the RF310R reader with RS422 interface ................................................ 105 5.3.5 Ensuring reliable data exchange............................................................................................... 105 5.3.6 Metal-free area.......................................................................................................................... 106 5.3.7 Minimum distance between RF310R readers........................................................................... 106 5.3.8 Technical specifications of the RF310R reader with RS422 interface...................................... 107 5.3.9 FCC information ........................................................................................................................ 108 5.3.10 Dimension drawing.................................................................................................................... 108 5.4 SIMATIC RF340R ..................................................................................................................... 109 5.4.1 Features .................................................................................................................................... 109 5.4.2 Ordering data for RF340R......................................................................................................... 109
Table of contents SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 7 5.4.3 Pin assignment of RF340R RS422 interface.............................................................................109 5.4.4 Display elements of the RF340R reader....................................................................................110 5.4.5 Ensuring reliable data exchange................................................................................................110 5.4.6 Metal-free area...........................................................................................................................110 5.4.7 Minimum distance between RF340R readers............................................................................111 5.4.8 Technical data of the RF340R reader........................................................................................111 5.4.9 FCC information.........................................................................................................................112 5.4.10 Dimension drawing ....................................................................................................................113 5.5 SIMATIC RF350R ......................................................................................................................113 5.5.1 Features.....................................................................................................................................113 5.5.2 Ordering data for RF350R .........................................................................................................114 5.5.3 Pin assignment of RF350R RS422 interface.............................................................................114 5.5.4 Display elements of the RF350R reader....................................................................................115 5.5.5 Ensuring reliable data exchange................................................................................................115 5.5.6 Metal-free area...........................................................................................................................115 5.5.7 Technical data of the RF350R reader........................................................................................115 5.5.8 FCC information.........................................................................................................................116 5.5.9 Dimension drawing ....................................................................................................................117 5.5.10 Antennas....................................................................................................................................118 5.5.10.1 Features.....................................................................................................................................118 5.5.10.2 Ordering data for antennas........................................................................................................119 5.5.10.3 Ensuring reliable data exchange................................................................................................119 5.5.10.4 Metal-free area...........................................................................................................................119 5.5.10.5 Minimum distance between antennas .......................................................................................121 5.5.10.6 Technical data for antennas.......................................................................................................123 5.5.10.7 Dimension drawings for antennas..............................................................................................124 5.6 SIMATIC RF380R ......................................................................................................................125 5.6.1 Features.....................................................................................................................................125 5.6.2 RF380R ordering data ...............................................................................................................125 5.6.3 Pin assignment of RF380R RS232/RS422 interface.................................................................126 5.6.4 Display elements of the RF380R reader....................................................................................126 5.6.5 Ensuring reliable data exchange................................................................................................126 5.6.6 Metal-free area...........................................................................................................................127 5.6.7 Minimum distance between RF380R readers............................................................................127 5.6.8 Technical specifications of the RF380R reader.........................................................................128 5.6.9 FCC information.........................................................................................................................129 5.6.10 Use of the reader in hazardous areas .......................................................................................129 5.6.11 Use of the reader in hazardous areas for gases........................................................................130 5.6.12 Installation and operating conditions for the hazardous area....................................................130 5.6.13 Dimension drawing ....................................................................................................................131 6 RF300 transponder................................................................................................................................ 133 6.1 Overview of RF300 tags ............................................................................................................133 6.2 Memory configuration of the RF300 tags...................................................................................134 6.3 SIMATIC RF320T ......................................................................................................................136 6.3.1 Features.....................................................................................................................................136 6.3.2 Ordering data .............................................................................................................................136 6.3.3 Mounting on metal .....................................................................................................................136 6.3.4 Technical data............................................................................................................................138 6.3.5 Dimension drawing ....................................................................................................................139 6.4 SIMATIC RF340T ......................................................................................................................139 6.4.1 Features.....................................................................................................................................139 6.4.2 Ordering data .............................................................................................................................139
Table of contents SIMATIC RF300 8 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 6.4.3 Mounting on metal..................................................................................................................... 140 6.4.4 Technical specifications ............................................................................................................ 141 6.4.5 Dimension drawing.................................................................................................................... 142 6.5 SIMATIC RF350T...................................................................................................................... 142 6.5.1 Features .................................................................................................................................... 142 6.5.2 Ordering data ............................................................................................................................ 143 6.5.3 Mounting on metal..................................................................................................................... 143 6.5.4 Technical data........................................................................................................................... 144 6.5.5 Dimension drawing.................................................................................................................... 146 6.6 SIMATIC RF360T...................................................................................................................... 147 6.6.1 Features .................................................................................................................................... 147 6.6.2 Ordering data ............................................................................................................................ 147 6.6.3 Mounting on metal..................................................................................................................... 147 6.6.4 Technical data........................................................................................................................... 150 6.6.5 Dimension drawing.................................................................................................................... 151 6.7 SIMATIC RF370T...................................................................................................................... 151 6.7.1 Features .................................................................................................................................... 151 6.7.2 Ordering data ............................................................................................................................ 152 6.7.3 Mounting on metal..................................................................................................................... 152 6.7.4 Mounting instructions ................................................................................................................ 154 6.7.5 Technical data for RF370T with 32 KB FRAM.......................................................................... 154 6.7.6 Dimensional drawing................................................................................................................. 155 6.8 SIMATIC RF380T...................................................................................................................... 156 6.8.1 Features .................................................................................................................................... 156 6.8.2 Ordering data ............................................................................................................................ 156 6.8.3 Installation guidelines for RF380T ............................................................................................ 157 6.8.3.1 Mounting instructions ................................................................................................................ 157 6.8.3.2 Metal-free area.......................................................................................................................... 159 6.8.4 Configuring instructions............................................................................................................. 161 6.8.4.1 Temperature dependence of the transmission window ............................................................ 161 6.8.4.2 Temperature response in cyclic operation ................................................................................ 163 6.8.5 Use of the transponder in the Ex protection area ..................................................................... 165 6.8.6 Use of the transponder in hazardous areas for gases.............................................................. 166 6.8.7 Installation and operating conditions for the hazardous area ................................................... 167 6.8.8 Technical specifications ............................................................................................................ 167 6.8.9 Dimensional drawing................................................................................................................. 168 7 ISO transponder .................................................................................................................................... 169 7.2 Memory configuration of the ISO tags ...................................................................................... 170 7.3 MDS D100................................................................................................................................. 172 7.3.1 Characteristics .......................................................................................................................... 172 7.3.2 Ordering data ............................................................................................................................ 172 7.3.3 Mounting on metal..................................................................................................................... 173 7.3.4 Technical data........................................................................................................................... 176 7.3.5 Dimension drawing.................................................................................................................... 177 7.4 MDS D124................................................................................................................................. 177 7.4.1 Characteristics .......................................................................................................................... 177 7.4.2 Ordering data ............................................................................................................................ 178 7.4.3 Mounting on metal..................................................................................................................... 178 7.4.4 Technical specifications ............................................................................................................ 179 7.4.5 Dimension drawing.................................................................................................................... 181 7.5 MDS D139................................................................................................................................. 181
Table of contents SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 9 7.5.1 Characteristics ...........................................................................................................................181 7.5.2 Ordering data .............................................................................................................................182 7.5.3 Mounting on metal .....................................................................................................................182 7.5.4 Technical specifications .............................................................................................................184 7.5.5 Use of the MDS D139 in hazardous areas ................................................................................185 7.5.6 Dimensional drawing..................................................................................................................185 7.6 MDS D160..................................................................................................................................186 7.6.1 Characteristics ...........................................................................................................................186 7.6.2 Information for RF300 compatibility ...........................................................................................186 7.6.3 Ordering data .............................................................................................................................187 7.6.4 Mounting on metal .....................................................................................................................187 7.6.5 Technical specifications .............................................................................................................188 7.6.6 Dimension drawing ....................................................................................................................189 7.7 MDS D324..................................................................................................................................190 7.7.1 Characteristics ...........................................................................................................................190 7.7.2 Ordering data .............................................................................................................................190 7.7.3 Mounting on metal .....................................................................................................................191 7.7.4 Technical specifications .............................................................................................................192 7.7.5 Dimension drawing ....................................................................................................................193 7.8 MDS D421..................................................................................................................................193 7.8.1 Characteristics ...........................................................................................................................193 7.8.2 Ordering data .............................................................................................................................194 7.8.3 Mounting on metal .....................................................................................................................194 7.8.4 Technical specifications .............................................................................................................196 7.8.5 Dimension drawing ....................................................................................................................197 7.9 MDS D424..................................................................................................................................198 7.9.1 Characteristics ...........................................................................................................................198 7.9.2 Ordering data .............................................................................................................................198 7.9.3 Mounting on metal .....................................................................................................................199 7.9.4 Technical specifications .............................................................................................................200 7.9.5 Dimension drawing ....................................................................................................................201 7.10 MDS D428..................................................................................................................................201 7.10.1 Characteristics ...........................................................................................................................201 7.10.2 Ordering data .............................................................................................................................202 7.10.3 Application example of MDS D428 ............................................................................................202 7.10.4 Technical specifications .............................................................................................................203 7.10.5 Dimension drawing ....................................................................................................................204 7.11 MDS D460..................................................................................................................................204 7.11.1 Characteristics ...........................................................................................................................204 7.11.2 Ordering data .............................................................................................................................205 7.11.3 Mounting on metal .....................................................................................................................205 7.11.4 Technical specifications .............................................................................................................206 7.11.5 Dimension drawing ....................................................................................................................207 8 System integration................................................................................................................................. 209 8.2 Introduction ................................................................................................................................209 8.3 ASM 452 ....................................................................................................................................211 8.3.1 Features.....................................................................................................................................211 8.3.2 Ordering data .............................................................................................................................211 8.3.3 Pin assignment and display elements .......................................................................................213 8.3.4 Configuration..............................................................................................................................214 8.3.5 Technical data............................................................................................................................217
Table of contents SIMATIC RF300 10 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 8.3.6 PROFIBUS Diagnosis............................................................................................................... 218 8.3.7 Dimension drawing.................................................................................................................... 219 8.4 ASM 456.................................................................................................................................... 220 8.5 ASM 473.................................................................................................................................... 221 8.5.1 Features .................................................................................................................................... 221 8.5.2 Ordering data ............................................................................................................................ 221 8.5.3 Pin assignment and display elements....................................................................................... 223 8.5.4 Configuration............................................................................................................................. 224 8.5.5 Technical data........................................................................................................................... 227 8.5.6 Dimensional drawings............................................................................................................... 228 8.6 ASM 475.................................................................................................................................... 229 8.6.1 Features .................................................................................................................................... 229 8.6.2 Ordering data ............................................................................................................................ 230 8.6.3 Indicators................................................................................................................................... 231 8.6.4 Configuration............................................................................................................................. 233 8.6.5 Technical data........................................................................................................................... 235 8.7 RF170C..................................................................................................................................... 237 8.8 RF180C..................................................................................................................................... 238 8.9 RF182C..................................................................................................................................... 239 8.10 8xIQ-Sense ............................................................................................................................... 240 8.10.1 Features .................................................................................................................................... 240 8.10.2 Ordering data ............................................................................................................................ 240 8.10.3 Indicators................................................................................................................................... 241 8.10.4 Configuration............................................................................................................................. 242 8.10.5 Addressing ................................................................................................................................ 244 8.10.6 Technical data........................................................................................................................... 246 9 System diagnostics................................................................................................................................ 247 9.1 Error codes................................................................................................................................ 247 9.2 Diagnostics functions ................................................................................................................ 248 9.2.1 Overview ................................................................................................................................... 248 9.2.2 Reader diagnostics with SLG Status ........................................................................................ 248 9.2.3 Transponder diagnostics with MDS Status............................................................................... 251 A Appendix................................................................................................................................................ 255 A.1 Certificates and approvals......................................................................................................... 255 A.2 Accessories............................................................................................................................... 257 A.3 Connecting cable ...................................................................................................................... 258 A.3.1 Reader RF3xxR (RS422) with ASM 452/ASM 473................................................................... 258 A.3.2 Reader RF3xxR (RS422) with ASM 456/RF170C/RF180C...................................................... 258 A.3.3 Reader RF3xxR (RS422) with ASM 475................................................................................... 259 A.3.4 RF310R and IQ-Sense.............................................................................................................. 260 A.3.5 Reader RF380R (RS232) - PC ................................................................................................. 260 A.4 Ordering data ............................................................................................................................ 261 A.5 Service & Support ..................................................................................................................... 266 Glossary ................................................................................................................................................ 269 Index...................................................................................................................................................... 271
SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 11 Introduction 11.1 Navigating in the system manual Structure of contents Contents Table of contents Organization of the documentation, including the index of pages and chapters Introduction Purpose, layout and description of the important topics. Safety instructions Refers to all the valid technical safety aspects which have to be adhered to while installing, commissioning and operating from the product/system view and with reference to statutory regulations. System overview Overview of all RF identification systems, system overview of SIMATIC RF300 RFID system planning Information about possible applications of SIMATIC RF300, support for application planning, tools for finding suitable SIMATIC RF300 components. Readers Description of readers which can be used for SIMATIC RF300 RF300 transponder Description of RF300 transponders which can be used for SIMATIC RF300 ISO transponder Description of ISO transponders which can be used for SIMATIC RF300 System integration Overview of the communication modules and function blocks that can be used for SIMATIC RF300 System diagnostics Description of system diagnostics available for SIMATIC RF300 Appendix  Certificates and approvals  Accessories  Connecting cable  Ordering data  Service & Support 1.2 Preface Purpose of this document This system manual contains all the information needed to plan and configure the system. It is intended both for programming and testing/debugging personnel who commission the system themselves and connect it with other units (automation systems, further programming devices), as well as for service and maintenance personnel who install expansions or carry out fault/error analyses. Scope of validity of this document This documentation is valid for all supplied variations of the SIMATIC RF300 system and describes the state of delivery as of November 2009.
Introduction 1.2 Preface SIMATIC RF300 12 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Conventions The following terms/abbreviations are used synonymously in this document: ● Reader, read/write device, write/read device ● Tag, transponder, mobile data memory, data carrier, MDS ● Communication module, interface module, ASM History Currently released versions of the SIMATIC RF300 system manual: Edition Remark 05/2005 First Edition 11/2005 Revised edition, components added: RF310R with RS422 interface, RF350T and RF360T; ASM 452, ASM 456, ASM 473 and ASM 475 04/2006 Revised edition, components added: RF340R as well as RF350R with the antenna types ANT 1, ANT 18 and ANT 30 12/2006 Revised edition, components added: RF370T, RF380T and RF170C 07/2007 Revised edition, degrees of protection changed for the RF300 reader 09/2007 Revised edition, components added: RF380R and RF180C 06/2008 Revised edition 01/2009 Revised edition, expanded by the reader functions "RF300 Tags" and "ISO Tags" for the SIMATIC RF310R and SIMATIC RF380R readers 11/2009 Revised edition, expanded by the reader functions "RF300 Tags" and "ISO Tags" for the SIMATIC RF340R and SIMATIC RF350R readers Expanded by the following components:  ANT 12 (in conjunction with RF350R)  ISO transponders MDS D421, MDS D424, MDS D428, MDS D460
SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 13 Safety information 2 SIMATIC RFID products comply with the salient safety specifications to IEC, VDE, EN, UL and CSA. If you have questions about the validity of the installation in the planned environment, please contact your service representative. CAUTION Alterations to the devices are not permitted. Failure to observe this requirement shall constitute a revocation of the radio equipment approval, CE approval and manufacturer's warranty. Repairs Repairs may only be carried out by authorized qualified personnel. WARNING Unauthorized opening of and improper repairs to the device may result in substantial damage to equipment or risk of personal injury to the user. System expansion Only install system expansion devices designed for this device. If you install other upgrades, you may damage the system or violate the safety requirements and regulations for radio frequency interference suppression. Contact your technical support team or your sales outlet to find out which system upgrades are suitable for installation. CAUTION If you cause system defects by installing or exchanging system expansion devices, the warranty becomes void.
SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 15 System overview 33.1 RFID systems RFID systems from Siemens control and optimize material flow. They identify reliably, quickly and economically, are insensitive to contamination and store data directly on the product. Identification system Frequency Range, max. Max. memory Data transfer rate (maximum) in byte/s Temperature, max. Special features RF300 13.56 MHz 0.2 m 20 byte EEPROM, 64 KB FRAM RF300 tags: 8000 ISO tags: - Read: 600 - Write: 400 Readers: -25 °C to +70 °C Transponder: -40 °C to +85 °C +220 °C cyclic IQ-Sense interface available; integrated diagnostic functions; battery-free data memory; additional ISO 15693 functionality (RF310R, 340R, RF350R, RF380R) MOBY D 13.56 MHz 0.8 m 112 byte EEPROM - Read: 600 - Write: 400 + 85 °C or + 200 °C SmartLabels based on ISO 15693 e.g. Tag-it/I-Code MOBY E 13.56 MHz 0,1 m 752 byte EEPROM - Read: 400 - Write: 350 + 150 °C Battery-free data memory MOBY I 1.81 MHz 0.15 m 32 KB FRAM 1250 + 85 °C or + 220 °C cyclic Battery-free data memory 3.2 SIMATIC RF300 3.2.1 RF300 system overview SIMATIC RF300 is an inductive identification system specially designed for use in industrial production for the control and optimization of material flow. Thanks to its compact dimensions, RF300 is the obvious choice where installation conditions are restricted, especially for assembly lines, handling systems and workpiece carrier systems. RF300 is suitable for both simple and demanding RFID applications and it stands out for its persuasive price/performance ratio.
System overview 3.2 SIMATIC RF300 SIMATIC RF300 16 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Low-performance applications With the cost-effective IQ-Sense interface, RF300 provides an especially favorable solution concept for low-performance applications. Medium-performance applications RF300 in conjunction with ISO tags provides a cost-effective solution for medium-performance applications. High-performance applications The high-performance components of RF300 provide advantages in terms of high data transmission rates and storage capacities. File handler functionality In addition to standard addressing, the ASM 456 interface module in conjunction with the FC 56 offers a file handler functionality. The required parameters correspond to those of MOBY I which are described in the FC56 documentation (http://support.automation.siemens.com/WW/view/en/18690683). Available ASMs can be found in an overview table in Chapter "System integration, Introduction (Page 209),Table 8-1).
System overview 3.2 SIMATIC RF300 SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 17 Table 3- 1 Overview of RF300 low-, medium- and high-performance components System components RF300 for low-performance applications RF300 for medium performance Applications with ISO 15693 tags RF300 for high-performance applications Communication modules 8xIQ-Sense for ET 200M (PROFIBUS) and for direct connection to an S7-300  ASM 452  ASM 456  ASM 473 (PROFIBUS)  ASM 475 (S7 300/ET 200M)  RF170C  RF180C  RF182C  ASM 452  ASM 456  ASM 473 (PROFIBUS)  ASM 475 (S7 300/ET 200M)  RF170C  RF180C  RF182C Readers  RF310R with IQ-Sense interface  RF310R with RS422 interface  RF340R  RF350R  RF380R  RF310R with RS422 interface  RF340R  RF350R  RF380R Transponder  RF320T  RF340T  RF350T  RF360T  MDS D100  MDS D124  MDS D1391)  MDS D1602)  MDS D324  MDS D421  MDS D424  MDS D428  MDS D460  RF320T  RF340T  RF350T  RF360T  RF370T  RF380T 1) only with the MLFB 6GT2600-0AA10 2) only with the MLFB 6GT2600-0AB10 3.2.2 RFID components and their function System components overview Component Description Communication module A communication module (interface module) is used to integrate the RF identification system in controllers/automation systems. Readers The reader (read/write device) ensures inductive communication and power supply to the transponder, and handles the connection to the various controllers (e.g. SIMATIC S7) through the communication module (e.g. ASM 475). Transponder The transponder (data memory) stores all data relevant to the production process and is used, for example, instead of barcode.
System overview 3.2 SIMATIC RF300 SIMATIC RF300 18 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 RF300 system components for low- and high-performance applications 7UDQVSRQGHU 5HDGHU &RPPXQLFDWLRQPRGXOHV3RZHUDQGGDWDWUDQVPLVVLRQ0+]6HULDODV\QFKURQRXVLQWHUIDFH56 56563&LQWHUIDFH7KLUGSDUW\3/&$60IRU6,0$7,&65)&IRU(7SUR$60IRU(7;$60IRU352),%86'39$60bIRU352),%86'3'395)&IRU352),1(7,2,46HQVHLQWHUIDFH[,46HQVHIRU(702Q65)5,46HQVH5)7 5)7 5)7 5)7 5)7 5)75)55)0 5)55)55)5 Figure 3-1 System overview low- and high-performance Table 3- 2 Reader-tag combination options for low- and high-performance applications Tags/ MDS RF310R (IQ-Sense) RF310R (RS422) RF340R RF350R with ANT 1 RF350R with ANT 18 RF350R with ANT 30 RF380R RF320T ✓ ✓ ✓ ✓ ✓ ✓ ✓ RF340T ✓ ✓ ✓ ✓ ✓ ✓ ✓ RF350T ✓ ✓ ✓ ✓ ○ ✓ ✓ RF360T ✓ ✓ ✓ ✓ -- ○ ✓ RF370T ○ ○ ✓ ✓ -- ○ ✓ RF380T ○ ○ ✓ ✓ -- -- ✓
System overview 3.2 SIMATIC RF300 SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 19 ✓ Combination possible -- Combination not possible ○ Combination possible, but not recommended @ in Grafik fehlt noch MDS D424 und die Fotos von MDS D460/MDS D424 RF300 system components for medium-performance applications 0'6'5HDGHUV &RPPXQLFDWLRQPRGXOHV3RZHUDQGGDWDWUDQVPLVVLRQ0+]6HULDODV\QFKURQRXVLQWHUIDFH56 56563&LQWHUIDFHWKLUGSDUW\3/&$60IRU6,0$7,&65)&IRU(7SUR$60IRU(7;$60IRU352),%86'39$60bIRU352),%86'3'395)&IRU352),1(7,27UDQVSRQGHU0'6'0'6' 0'6' 0'6' 0'6' 0'6' 0'6'5)0 5)55)5 5)5 5)5 Figure 3-2 System overview medium-performance
System overview 3.2 SIMATIC RF300 SIMATIC RF300 20 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Table 3- 3 Reader-tag combination options for medium-performance applications Tags/ MDS RF310R (IQ-Sense) RF310R (RS422) RF340R RF350R with ANT 1 RF350R with ANT 12 RF350R with ANT 18 RF350R with ANT 30 RF380R MDS D100 -- ✓ ✓ ✓ -- -- ○ ✓ MDS D124 -- ✓ ✓ ✓ ○ ✓ ✓ ✓ MDS D139 -- ○ ✓ ✓ -- -- ○ ✓ MDS D160 -- ✓ ✓ ✓ ✓ ✓ ✓ ✓ MDS D324 -- ✓ ✓ ✓ ○ ✓ ✓ ✓ MDS D421 -- -- -- -- ✓ ✓ -- -- MDS D424 -- ✓ ✓ ✓ ○ ✓ ✓ ✓ MDS D428 -- ✓ ✓ ✓ ✓ ✓ ✓ ✓ MDS D460 -- ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Combination possible -- Combination not possible ○ Combination possible, but not recommended Note ISO15693 is only possible with MLFB 6GT2801-xxBxx readers. Conventions The RF310R, RF340R and RF380R readers are equipped with an integral antenna, whereas the RF350R reader is operated over an external antenna. In this system manual, the term "Reader" is used throughout even where it is actually referring to the antenna of the reader. 3.2.3 Application areas of RF300 SIMATIC RF300 is primarily used for non-contact identification of containers, palettes and workpiece holders in a closed production circuit. The data carriers (transponders) remain in the production chain and are not supplied with the products. SIMATIC RF300, with its compact transponder and reader enclosure dimensions, is particularly suitable in confined spaces. Main applications ● Mechanical engineering, automation systems, conveyor systems ● Ancillary assembly lines in the automotive industry, component suppliers ● Small assembly lines
System overview 3.3 System configuration SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 21 Application examples ● Production lines for engines, gearboxes, axles, etc. ● Assembly lines for ABS systems, airbags, brake systems, doors, cockpits, etc. ● Assembly lines for household electrical appliances, consumer electronics and electronic communication equipment ● Assembly lines for PCs, small-power motors, contactors, switches Advantages ● Reading and writing of large data volumes within a short time results in shorter production cycle times and thus help to boost productivity ● Can be used in harsh environments thanks to rugged components with high degree of protection ● Simple and low-cost system integration into SIMATIC S7 and PROFIBUS (TIA) ● Shorter commissioning times and fewer plant failures and downtimes thanks to integral diagnostic functionalities ● Cost savings thanks to maintenance-free components 3.3 System configuration 3.3.1 Overview The SIMATIC RF300 system is characterized by a high level of standardization of its components. This means that the system follows the TIA principle throughout: Totally Integrated Automation. It provides maximum transparency at all levels with its reduced interface overhead. This ensures optimum interaction between all system components. The RF300 system with its flexible components offers many possibilities for system configuration. This chapter shows you how you can use the RF300 components on the basis of various example scenarios. 3.3.2 Assembly line example: Use of RF300 tags In assembly lines, such as in engine manufacturing, many work steps are completed in succession. Automated or manual assembly work is carried out at the individual workstations in relatively short periods of time. The special features of the RF300 tags, which stand out for their large data memory and high transmission speeds, bring about many advantages in regard to the production unit numbers of such plants. The possibility of saving large volumes of data means savings in terms of data management on the HOST system and considerably contributes to data security. (redundant data management, e.g. HOST database, or controller and data carrier) Advantages at a glance:
System overview 3.3 System configuration SIMATIC RF300 22 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 ● Redundant data storage on the basis of large memory, availability of decentralized data ● High data rate ● Data management savings on the host system Characteristics of the scenario In this example scenario, engine blocks that are placed on metal pallets are conveyed on an assembly line. The engines are assembled piece-by-piece at the individual workstations. The SIMATIC RF340T RFID tag is securely affixed on the underside of the pallet. The transport speed is approx. 0.5 m/s. In this scenario, it is an advantage that the tag can be directly secured to metal on the metal pallets. The small-dimensioned SIMATIC RF310R reader is integrated in the conveyor elements in such a manner that it can communicate with the tags from below. Thus, it is not necessary to align the pallets or to attach several tags. The data of the entire production order (5000 bytes) is stored on the tag. This data is read at each workstation and changed or supplemented depending on the workstation, and then written back again. Thus, the status of the engine block assembly can be determined at any point in time, even if there is a failure at the HOST level. Thanks to the extremely high data rate, a very short cycle time for the work steps can be factored in, which results in high end product unit numbers (engines). The entire production order that is saved on the tag can also be manually read via the WIN-LC terminal located at each workstation. This means that virtually no additional data management is required on the control PC. The production order data can also be read for servicing purposes via the mobile SIMATIC RF310M handheld terminal.
System overview 3.3 System configuration SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 23 0HWDOSDOOHW(QJLQHEORFN6,0$7,&6FRQWUROOHU+DQGKHOGWHUPLQDO5)0$605)75)5 Figure 3-3 Example of engine block production 3.3.3 Example of container and paper board container handling: Use of ISO tags Containers of varying sizes are conveyed to picking workstations in a delivery center. There, the individual goods are removed and packed in cartons according to the delivery note. These cartons are marked with low-cost transponder labels and sorted to small or large packaging workstations (according to the delivery note) by being guided or transported via the corresponding conveyor system. The containers are marked using the MDS D100 ISO tag. Advantages at a glance: ● Decision points in the conveyor system can be installed in a more favorable way (mechanically) ● Different sizes of containers with different depths can be identified due to the range
System overview 3.3 System configuration SIMATIC RF300 24 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 ● In contrast to bar codes, tags can also be written to ● Different types of tags can be processed using one and the same reader Characteristics of the scenario In this example scenario, containers of varying sizes are conveyed on a conveyor system. Only the unique identification number (8 bytes) is read. The containers to be picked are sorted to the corresponding workstations. The maximum transport speed is 1.0 m/s. In this scenario, it is an advantage that the RF380R reader can read and write the tags at different distances on the containers without a great deal of mechanical or control system effort due to the reading range. During the picking process, the goods are immediately placed in different containers or packed in cartons depending on the destination (small packaging or large packaging station). The containers are equipped with the MDS D100 ISO tag. The low-cost "one-way tag" (label) is used on the cartons: it is simply glued onto the carton. Thus the goods can be identified at any time. Again, one and the same reader is used for this. The maximum transport speed is 0.8 m/s. In addition, flexible identification is possible at each location and at any time using the mobile SIMATIC RF310M handheld terminal.
System overview 3.4 System data SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 25 5)5UHDGHU6,0$7,&6FRQWUROOHU+DQGKHOGWHUPLQDO5)00'6'$60 Figure 3-4 Example of container and paper board container handling 3.4 System data Type Inductive identification system for industrial applications Transmission frequency data/energy 13.56 MHz Memory capacity  20 bytes to 64 KB user memory (r/w)  4 bytes fixed code as serial number (ro) Memory type EEPROM / FRAM Write cycles  EEPROM: > 200 000  FRAM: Unlimited
System overview 3.4 System data SIMATIC RF300 26 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Read cycles Unlimited Data management Byte-by-byte access RF300 tags ISO tags Read (maximum values) 8000 byte/s approx. 600 byte/s Data transmission rate Transponder reader Write (maximum values) approx. 8000 byte/s approx. 400 byte/s Read/write distance (system limit; depends on reader and transponder)  RF300 tags: up to 0.15 m  ISO tags: up to 0.2 m Readers: -25°C to +70°C Operating temperature Transponder: -40 to +125 °C +220 °C cyclically Degree of protection Reader: IP 67 2) Transponder: > IP 67 Can be connected to  SIMATIC S7-300  PROFIBUS DP V1  PROFINET  PC 1)  Third-party control 1) Special features  Very high data transfer rate  High noise immunity  Compact components  Extensive diagnostic options  A reader with IQ-Sense interface  ISO 15693 functionality can be parameterized Approvals  ETS 300 330 (Europe)  FCC Part 15 (USA),  UL/CSA CE,  operating license for Japan 1) By means of RS422 interface and 3964R protocol 2) Exception RF350R: IP 65
SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 27 RF300 system planning 44.1 Fundamentals of application planning 4.1.1 Selection criteria for SIMATIC RF300 components Assess your application according to the following criteria, in order to choose the right SIMATIC RF300 components: ● Transmission distance (read/write distance) ● Tracking tolerances ● Static or dynamic data transfer ● Data volume to be transferred ● Speed in case of dynamic transfer ● Metal-free rooms for transponders and readers ● Ambient conditions such as relative humidity, temperature, chemical impacts, etc. 4.1.2 Transmission window and read/write distance The reader generates an inductive alternating field. The field is strongest near to the reader. The strength of the field decreases in proportion to the distance from the reader. The distribution of the field depends on the structure and geometry of the antennas in the reader and transponder. A prerequisite for the function of the transponder is a minimum field strength at the transponder achieved at a distance Sg from the reader or the ANT1. The picture below shows the transmission window between transponder and reader or ANT1:
RF300 system planning 4.1 Fundamentals of application planning SIMATIC RF300 28 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Table 4- 1 RF310R reader and ANT 1 (RF350R) transmission window and read/write distance 3ODQYLHZ6LGHYLHZ7UDQVSRQGHU7UDQVSRQGHU7UDQVPLVVLRQZLQGRZ636J6D/'/6DPD[ /G/6DPLQ /PD[6,(0(166,0$7,&5)75)7 Sa: Operating distance between transponder and reader Sg Limit distance (maximum clear distance between upper surface of the reader and the transponder, at which the transmission can still function under normal conditions) L Length of a transmission window The length Ld is valid for the calculation. At Sa,min , the field length increases from Ld to Lmax. SP Intersection of the axes of symmetry of the transponder
RF300 system planning 4.1 Fundamentals of application planning SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 29 Table 4- 2 RF340R reader transmission window and read/write distance 7UDQVSRQGHU637RSYLHZ7UDQVPLVVLRQZLQGRZ6LGHYLHZ)URQWYLHZ7UDQVSRQGHU0/[PD[/[PD[6DPLQ/[/\PD[6DPLQ/[/\6,(0(166,0$7,&5)75)7/\6J6D/\PD[ All dimensions in mm. Sa: Operating distance between transponder and reader Sg Limit distance (maximum clear distance between upper surface of the reader and the transponder, at which the transmission can still function under normal conditions) Lx Length of a transmission window in the x-direction (Lx = Ly with RF340R) The length Lx is valid for the calculation. At Sa,min , the field length increases from Lx to Lmax. Ly Length of a transmission window in the y-direction (Lx = Ly with RF340R) The length Ly is valid for the calculation. At Sa,min , the field length increases from Ly to Ly max. M Field centerpoint
RF300 system planning 4.1 Fundamentals of application planning SIMATIC RF300 30 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Table 4- 3 ANT 12, ANT 18 and ANT 30 (RF350R) transmission window and read/write distance 637RSYLHZ6LGHYLHZ7UDQVPLVVLRQZLQGRZ6,(0(167UDQVSRQGHU6,0$7,&5)77UDQVSRQGHU5)7/6DPD[ /G6J6D/G/6DPLQ /PD[/PD[0'6' Sa: Operating distance between transponder and reader Sg Limit distance (maximum clear distance between upper surface of the reader and the transponder, at which the transmission can still function under normal conditions) L Diameter of a transmission window The length Ld is valid for the calculation. At Sa,min , the field length increases from Ld to Lmax. SP Intersection of the axes of symmetry of the transponder
RF300 system planning 4.1 Fundamentals of application planning SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 31 Table 4- 4 RF380R reader transmission window and read/write distance 7RSYLHZ)URQWYLHZ6LGHYLHZ7UDQVPLVVLRQZLQGRZ7UDQVSRQGHU7UDQVSRQGHU63/\6J6D/[/[PD[6DPLQ/\6DPLQ/[PD[/\PD[/\/[06,(0(166,0$7,&5)75)7 Sa: Operating distance between transponder and reader Sg Limit distance (maximum clear distance between upper surface of the reader and the transponder, at which the transmission can still function under normal conditions) Lx Length of a transmission window in the x direction The length Lx is valid for the calculation. At Sa,min , the field length increases from Lx to Lmax. Ly Length of a transmission window in the y direction The length Ly is valid for the calculation. At Sa,min , the field length increases from Ly to Ly max. M Field centerpoint The transponder can be used as soon as the intersection (SP) of the transponder enters the area of the transmission window.
RF300 system planning 4.1 Fundamentals of application planning SIMATIC RF300 32 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 From the diagrams above, it can also be seen that operation is possible within the area between Sa and Sg. The active operating area reduces as the distance increases, and shrinks to a single point at distance Sg. Only static mode should thus be used in the area between Sa and Sg. 4.1.3 Width of the transmission window Determining the width of the transmission window The following approximation formula can be used for practical applications: % y/ B: Width of the transmission window L: Length of the transmission window Tracking tolerances The width of the transmission window (B) is particularly important for the mechanical tracking tolerance. The formula for the dwell time is valid without restriction when B is observed. 4.1.4 Impact of secondary fields Secondary fields in the range from 0 to 20 mm always exist. They should only be applied during planning in exceptional cases, however, since the read/write distances are very limited. Exact details of the secondary field geometry cannot be given, since these values depend heavily on the operating distance and the application.
RF300 system planning 4.1 Fundamentals of application planning SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 33 Secondary fields without shielding The following graphic shows typical primary and secondary fields, if no shielding measures are taken. 7DJ6HFRQGDU\ILHOG0DLQILHOG5HDGHU7DJ7DJ&RQYH\LQJGLUHFWLRQ&RQYH\LQJGLUHFWLRQ Figure 4-1 Secondary field without shielding In this arrangement, the reader can also read tags via the secondary field. Shielding is required in order to prevent unwanted reading via the secondary field, as shown and described in the following. Secondary fields with shielding The following graphic shows typical primary and secondary fields, with metal shielding this time. The metal shielding prevents the reader from detecting tags via the secondary field.
RF300 system planning 4.1 Fundamentals of application planning SIMATIC RF300 34 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 5HDGHUV6HFRQGDU\ILHOG 0DLQILHOG0HWDOVKLHOGLQJ&RQYH\RUGLUHFWLRQ&RQYH\RUGLUHFWLRQ7DJ7DJ7DJ Figure 4-2 Secondary field with shielding
RF300 system planning 4.1 Fundamentals of application planning SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 35 4.1.5 Permissible directions of motion of the transponder Detection area and direction of motion of the transponder The transponder and reader have no polarization axis, i.e. the transponder can come in from any direction, be placed at any position, and cross the transmission window. The figure below shows the active area for various directions of transponder motion: RU RU%%%/// Transmission window Direction of motion of the transponder Detection area L x W Figure 4-3 Detection areas of the reader for different directions of transponder motion 4.1.6 Operation in static and dynamic mode Operation in static mode If working in static mode, the transponder can be operated up to the limit distance (Sg). The transponder must then be positioned exactly over the reader: 7UDQVPLVVLRQZLQGRZ7UDQVSRQGHU5HDGHU6J Figure 4-4 Operation in static mode
RF300 system planning 4.1 Fundamentals of application planning SIMATIC RF300 36 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Operation in dynamic mode When working in dynamic mode, the transponder moves past the reader. The transponder can be used as soon as the intersection (SP) of the transponder enters the circle of the transmission window. In dynamic mode, the operating distance (Sa) is of primary importance. [Operating distances, see Chapter Field data for transponders, readers and antennas (Page 41)] 7UDQVPLVVLRQZLQGRZ7UDQVSRQGHU7UDQVSRQGHU3ODQYLHZ6363 Figure 4-5 Operation in dynamic mode 4.1.7 Dwell time of the transponder The dwell time is the time in which the transponder remains within the transmission window of a reader. The reader can exchange data with the transponder during this time. The dwell time is calculated thus: 0,8 [ ][/]TagvL mtv m s⋅= tV: Dwell time of the transponder L: Length of the transmission window vTag: Speed of the transponder (tag) in dynamic mode 0,8: Constant factor used to compensate for temperature impacts and production tolerances The dwell time can be of any duration in static mode. The dwell time must be sufficiently long to allow communication with the transponder. The dwell time is defined by the system environment in dynamic mode. The volume of data to be transferred must be matched to the dwell time or vice versa. In general:
RF300 system planning 4.1 Fundamentals of application planning SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 37 Kvtt≥ tV:: Dwell time of the data memory within the field of the reader tK: Communication time between transponder and communication module 4.1.8 Communication between communication module, reader and transponder Communication between the communication module, reader and transponder takes place asynchronously through the RS422 interface. Depending on the communication module (ASM) used, transfer rates of 19200 baud, 57600 baud or 115200 baud can be selected. Calculation of the communication time for interference-free transfer The communication time for fault-free data transfer is calculated as follows: =+ ⋅tKtnKByte(n >1) If the transmission is interrupted briefly due to external interference, the communication module automatically continues the command. Calculation of the maximum amount of user data The maximum amount of user data is calculated as follows: tk: Communication time between communication module, reader and transponder tv: Dwell time n: Amount of user data in bytes nmax: Max. amount of user data in bytes in dynamic mode tbyte: Transmission time for 1 byte K: Constant; the constant is an internal system time. This contains the time for power buildup on the transponder and for command transfer
RF300 system planning 4.1 Fundamentals of application planning SIMATIC RF300 38 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Time constants K and tbyte for medium and high-performance applications Table 4- 5 Static mode RF300 mode FRAM ISO mode Read/write Read Write Data volume ≤ 233 bytes Data volume >233 bytes Data volume ≤ 233 bytes Data volume >233 bytes Independent of data volume Transfer rate [baud] K [ms] tbyte [ms] K [ms] tbyte [ms] K [ms] tbyte [ms] K [ms] tbyte [ms] K [ms] tbyte [ms] 19200 28 0.67 28 0.67 35 1.08 64 0.75 41 2.66 57600 15 0.30 25 0.22 34 0.59 34 0.59 28 2.28 115200 11 0.21 30 0.12 26 0.56 26 0.56 26 2.17 The values for K and tbyte include the overall time that is required for communication in static mode. It is built up from several different times:  Serial communication between communication module, reader and  Processing time between reader and transponder and their internal processing time. The values shown in the table must be used when calculating the maximum quantity of user data in static mode. They are applicable for both reading and writing in the FRAM area. For writing in the EEPROM area (max. 20 bytes), the byte time tByte is approx. 11 ms. Table 4- 6 Dynamic mode RF300 tags ISO tags Transfer rate [baud] Memory area K [ms] tbyte [ms] K [ms] tbyte [ms] Independent FRAM 8 0.13 - - Independent Write Read EEPROM 8 8 12.20 0.13 15 12 1.99 0.56 In dynamic mode, the values for K and tbyte are independent of the transmission speed. The communication time only includes the processing time between the reader and the transponder and the internal system processing time of these components. The communication times between the communication module and the reader do not have to be taken into account because the command for reading or writing is already active when the transponder enters the transmission field of the reader. The values shown above must be used when calculating the maximum quantity of user data in dynamic mode. They are applicable for both writing and reading.
RF300 system planning 4.1 Fundamentals of application planning SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 39 Time constants K and tbyte for low-performance applications (IQ-Sense) Table 4- 7 Static mode K (ms) tbyte (ms) Command 15 15 Read (FRAM/EEPROM area) 15 15 Write (FRAM area) 30 30 Write (EEPROM area) The table of time constants applies to every command. If a user command consists of several subcommands, the above tK formula must be applied to each subcommand. 4.1.9 Calculation example (RS422) A transport system moves pallets with transponders at a maximum velocity of VTag = 1.0 m/s (dynamic mode). The following RFID components were selected: ● ASM 475 communication module ● RF310R reader with RS422 interface ● Transponder RF340T Task a) The designer of the plant is to be given mechanical specifications. b) The programmer should be given the maximum number of bytes in dynamic mode. Refer to the tables in the "Field data of transponders and readers" section for the technical data. Determine tolerance of pallet transport height 'LUHFWLRQRIPRWLRQ7UDQVSRQGHUVLGHYLHZ++6D+PP5HDGHUV Figure 4-6 Tolerance of pallet transport height
RF300 system planning 4.1 Fundamentals of application planning SIMATIC RF300 40 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Determine tolerance of pallet side transport &HQWHUOLQHRIWUDQVSRQGHUDQGUHDGHU'LUHFWLRQRIPRWLRQRIWKHWUDQVSRQGHU% ZLGWKRIWKHWUDQVPLVVLRQZLQGRZLQG\QDPLFPRGH%7ROHUDQFHEDQGRIVLGHWUDQVSRUW7UDQVSRQGHU5HDGHUV Figure 4-7 Tolerance of pallet side transport Minimum distance from reader to reader Refer to the field data of the reader for this value. Minimum distance from transponder to transponder Refer to the field data of the transponder for this value. Calculation of the maximum amount of user data in dynamic mode Step Formula/calculation 1. Calculate dwell time of the transponder Refer to the "Field data of all transponders and readers" table for value L. Value vTag = 1.00 m/s /ವY7DJPವPVWY V PV 2. Calculate maximum user data (nmax) for reading or writing (FRAM area) Take value tv from Step 1. Take values K and t Byte from Table "Time constants K and t Byte". 5HDGZULWH QPD[ปE\WHVE\WHVWE\WHVWY.PVPVPV යResult A maximum of 172 bytes can be read or written when the transponder passes by.
RF300 system planning 4.2 Field data for transponders, readers and antennas SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 41 4.2 Field data for transponders, readers and antennas The following table shows the field data for all SIMATIC RF300 components of transponders and readers. It facilitates the correct selection of a transponder and reader. All the technical specifications listed are typical data and are applicable for an ambient temperature of between 0 C and +50 °C, a supply voltage of between 22 V and 27 V DC and a metal-free environment. Tolerances of ±20 % are admissible due to production or temperature conditions. If the entire voltage range at the reader of 20 V DC to 30 V DC and/or the entire temperature range of transponders and readers is used, the field data are subject to further tolerances. Note Transmission gaps If the minimum operating distance (Sa) is not observed, a transmission gap can occur in the center of the field. Communication with the transponder is not possible in the transmission gap. 4.2.1 Field data of RF300 transponders Observe the following information for field data of RF300 transponders: ● A maximum median deviation of ±2 mm is possible in static mode (without affecting the field data) ● The field data are reduced by approx. 15% if the transponder enters the transmission window laterally (see also "Transmission window" figure) RF310R reader Table 4- 8 RF310R reader Length of transmission window (L) Operating distance (Sa) Limit distance (Sg) RF320T 30 2...10 16 RF340T 38 2...20 26 RF350T 45 5...22 [26] 30 [35] RF360T 45 5...26 35 All values are in mm Values in brackets [ ] refer to RF310R with the MLFB 6GT2801-1AB10
RF300 system planning 4.2 Field data for transponders, readers and antennas SIMATIC RF300 42 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 RF340R reader Table 4- 9 RF340R reader Length of the transmission window (L) Operating distance (Sa) Limit distance (Sg) RF320T 45 2...20 25 RF340T 60 5...25 35 RF350T 60 5...35 50 RF360T 70 8...40 60 RF370T 75 15...36 52 RF380T 85 15...47 55 All values are in mm RF350R reader / ANT 1 Table 4- 10 RF350R reader / ANT 1 Length of the transmission window (L) Operating distance (Sa) Limit distance (Sg) RF320T 45 2...20 25 RF340T 60 5...25 35 RF350T 60 5...35 50 RF360T 70 8...40 60 RF370T 70 15...45 65 RF380T 88 15...53 65 All values are in mm RF350R reader / ANT 18 Table 4- 11 RF350R reader / ANT 18 Diameter of the transmission window (Ld) Operating distance (Sa) Limit distance (Sg) RF320T 10 2...8 10 RF340T 20 2...10 13 All values are in mm
RF300 system planning 4.2 Field data for transponders, readers and antennas SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 43 RF350R reader / ANT 30 Table 4- 12 RF350R reader / ANT 30 Diameter of the transmission window (Ld) Operating distance (Sa) Limit distance (Sg) RF320T 15 2...11 15 RF340T 25 5...15 20 RF350T 25 5...16 22 RF380R reader Table 4- 13 RF380R reader Length of the transmission window in the x-direction (Lx) in the y-direction (Ly) Operating distance (Sa) Limit distance (Sg) RF320T 100 40 2...30 [40] 47 [55] RF340T 115 50 20...70 [80] 90 [100] RF350T 120 60 35...70 [100] 105 [130] RF360T 120 70 40...120 140 [150] RF370T 135 65 35...85 [100] 125 [135] RF380T 155 75 25...85 [110] 125 [140] All values are in mm Values in brackets [ ] refer to RF380R with the MLFB 6GT2801-3AB10 The RF380R with MLFB 6GT2801-3AB10 enables the user to set the transmission output power with the aid of the "distance_limiting" input parameter. For this, values from approx. 0.5 W to approx. 2.0 W can be set in 0.25 W increments. Depending on the setting, the change to the transmission output power increases the performance in the lower operating distance (low performance) or in the upper limit distance (high performance). The "dili" value range goes from 02 (= 0.5 W) and 05 (default value: 1.25 W) to 08 (= 2 W). Note A dili value setting outside of the value range of 02 to 08 leads to the default setting (05) and does not generate an error message. Also see Chapter Minimum clearances (Page 47) Section "Minimum distance from reader to reader". You can find exact information regarding the parameters in the Product Information "FB 45 and FC 45 input parameters for RF300 and ISO transponders" (http://support.automation.siemens.com/WW/view/en/33315697).
RF300 system planning 4.2 Field data for transponders, readers and antennas SIMATIC RF300 44 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 4.2.2 Field data of ISO transponders Observe the following information for field data of ISO transponders: ● A maximum median deviation of ±2 mm is possible in static mode (without affecting the field data) ● The field data are reduced by approx. 15% if the transponder enters the transmission window laterally (see also "Transmission window" figure) RF310R reader Length of the transmission window (L) Operating distance (Sa) Limit distance (Sg) MDS D100 50 2...78 90 MDS D124 30 2...22 30 MDS D160 36 2...25 37 MDS D324 40 2...30 38 MDS D424 MDS D428 MDS D460 1) Combination with the RF310R is basically possible, but is not recommended because the antenna geometries for the reader and transponder are not ideally matched. All values are in mm RF340R reader Table 4- 14 RF340R reader Length of the transmission window (Lx) Operating distance (Sa) Limit distance (Sg) MDS D100 MDS D124 MDS D139 MDS D160 MDS D324 MDS D421 MDS D424 MDS D428 MDS D460 All values are in mm
RF300 system planning 4.2 Field data for transponders, readers and antennas SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 45 RF350R reader / ANT 1 Table 4- 15 RF340R reader / ANT 1 Length of the transmission window (L) Operating distance (Sa) Operating distance (Sa) MDS D100 MDS D124 MDS D139 MDS D160 MDS D324 MDS D424 MDS D428 MDS D460 All values are in mm RF350R reader with ANT 12 Table 4- 16 RF340R reader / ANT 12 Length of the transmission window (L) Operating distance (Sa) Limit distance (Sg) MDS D160 MDS D421 MDS D428 MDS D460 RF350R reader with ANT 18 Table 4- 17 RF340R reader / ANT 18 Length of the transmission window (L) Operating distance (Sa) Limit distance (Sg) MDS D124 MDS D160 MDS D324 MDS D421 MDS D424 MDS D428 MDS D460
RF300 system planning 4.2 Field data for transponders, readers and antennas SIMATIC RF300 46 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 RF350R reader with ANT 30 Table 4- 18 RF340R reader / ANT 30 Length of the transmission window (L) Operating distance (Sa) Limit distance (Sg) MDS D124 MDS D160 MDS D324 MDS D424 MDS D428 MDS D460 RF380R reader Table 4- 19 RF380R reader Length of the transmission window Operating distance (Sa) Limit distance (Sg) in the x-direction (Lx) in the y-direction (Ly) MDS D100 160 100 15…170 210 MDS D124 100 80 0…72 90 MDS D139 155 90 15...160 200 MDS D160 120 40 0…64 80 MDS D324 130 60 0…96 120 MDS D424 MDS D428 MDS D460 All values are in mm Note Only the MDS D139 with MLFB 6GT2600-0AA10 is compatible with SIMATIC RF300.
RF300 system planning 4.2 Field data for transponders, readers and antennas SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 47 4.2.3 Minimum clearances Minimum distance from transponder to transponder The specified distances refer to a metal-free environment. For a metallic environment, the specified minimum distances must be multiplied by a factor of 1.5. Table 4- 20 RF300 tags RF310R RF340R RF350R / ANT 1 RF350R / ANT 12 RF350R / ANT 18 RF350R / ANT 30 RF380R RF320T ≥ 50 ≥ 70 ≥ 70 ≥ 20 ≥ 40 ≥ 120 RF340T ≥ 60 ≥ 80 ≥ 80 ≥ 40 ≥ 40 ≥ 140 RF350T ≥ 60 ≥ 80 ≥ 80 __ ≥ 50 ≥ 150 RF360T ≥ 60 ≥ 80 ≥ 80 __ __ ≥ 120 RF370T __ ≥ 80 ≥ 80 __ __ ≥ 130 RF380T __ ≥ 80 ≥ 80 __ __ ≥ 150 The values are all in mm, relative to the operating distance (Sa) between reader and tag Table 4- 21 ISO tags RF310R RF340R RF350R / ANT 1 RF350R / ANT 12 RF350R / ANT 18 RF350R / ANT 30 RF380R MDS D100 ≥ 120 ≥ 300 MDS D124 ≥ 100 ≥ 170 MDS D139 ≥ 120 ≥ 230 MDS D160 ≥ 120 ≥ 150 MDS D324 ≥ 120 ≥ 250 MDS D421 MDS D424 MDS D428 MDS D460 The values are all in mm, relative to the operating distance (Sa) between reader and tag
RF300 system planning 4.2 Field data for transponders, readers and antennas SIMATIC RF300 48 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Minimum distance from reader to reader RF310R to RF310R RF340R to RF340R RF380R to RF380R1) ≥ 100 ≥ 100 ≥ 400 All values are in mm 1) The permissible minimum distance between two RF380Rs depends on the transmission output power that is set. The specified minimum distance must be multiplied by the following factor, depending on the output: DILI byte Factor 02; 03 0,8 04; 05; 06 1,0 07; 08 1,2 Minimum distance from antenna to antenna ANT1 ANT18 ANT30 ≥ 100 ≥ 100 ≥ 100 All values are in mm See also Minimum distance between antennas (Page 121) NOTICE Effect on inductive fields by not maintaining the minimum distances of the readers When the values specified in the "minimum distance from reader to reader" table are not met, there is a risk of affecting inductive fields. In this case, the data transfer time would increase unpredictably or a command would be aborted with an error. Adherence to the values specified in the "Minimum distance from reader to reader" table is therefore essential. If the specified minimum distance cannot be complied with due to the physical configuration, the SET-ANT command can be used to activate and deactivate the HF field of the reader. The application software must be used to ensure that only one reader is active (antenna is switched on) at a time. Note Please also observe the graphic representations of the minimum distances in the respective chapters on readers.
RF300 system planning 4.3 Dependence of the volume of data on the transponder speed with RF300 tags SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 49 4.3 Dependence of the volume of data on the transponder speed with RF300 tags The curves seen here show the relation between speed and data transfer volume for each transponder. They should make it easier to preselect the transponders for dynamic use. 4.3.1 RF320T with RF310R, RF340R, RF350R, RF380R The following table is used to calculate the curves. The indicated speeds are applicable for operation without presence check. RF310R RF340R/ RF350R RF380R Operating distance (Sa) 10 mm 10 mm 40 mm RF320T: Display of speed relative to data volume (write)       ① RF380R ② RF340R / RF350R + ANT 1 ③ RF310R Figure 4-8 RF320T with RF310R, RF340R/RF350R, RF380R 4.3.2 RF340T with RF310R, RF340R, RF350R, RF380R The following table is used to calculate the curves. The indicated speeds are applicable for operation without presence check.
RF300 system planning 4.3 Dependence of the volume of data on the transponder speed with RF300 tags SIMATIC RF300 50 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 RF310R RF340R/ RF350R RF380R Operating distance (Sa) 20 mm 20 mm 40 mm RF340T: Display of speed relative to data volume (read/write) %\WHYPV          5)55)55)55)5$17 Figure 4-9 RF340T with RF310R, RF340R/RF350R and RF380R 4.3.3 RF350T with RF310R, RF340R, RF350R, RF380R The following table is used to calculate the curves. The indicated speeds are applicable for operation without presence check. RF310R RF340R/ RF350R RF380R Operating distance (Sa) 22 mm 22 mm 40 mm
RF300 system planning 4.3 Dependence of the volume of data on the transponder speed with RF300 tags SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 51 RF350T: Display of speed relative to data volume (read/write)           %\WHYPV5)55)55)55)5$17 Figure 4-10 RF350T with RF310R, RF340R/RF350R and RF380R 4.3.4 RF360T with RF310R, RF340R, RF350R, RF380R The following table is used to calculate the curves. The indicated speeds are applicable for operation without presence check. RF310R RF340R/ RF350R RF380R Operating distance (Sa) 26 mm 26 mm 60 mm
RF300 system planning 4.3 Dependence of the volume of data on the transponder speed with RF300 tags SIMATIC RF300 52 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 RF360T: Display of speed relative to data volume (read/write)           5)55)55)55)5$17%\WHYPV Figure 4-11 RF360T with RF310R, RF340R/RF350R and RF380R 4.3.5 RF370T with RF340R, RF350R, RF380R The following table is used to calculate the curves. The indicated speeds are applicable for operation without presence check. RF340R/ RF350R RF380R Operating distance (Sa) 22 mm 60 mm
RF300 system planning 4.3 Dependence of the volume of data on the transponder speed with RF300 tags SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 53 RF370T: Display of speed relative to data volume (read/write)           5)55)55)5$17%\WHYPV Figure 4-12 RF370T with RF340R/RF350R and RF380R 4.3.6 RF380T with RF340R, RF350R, RF380R The following table is used to calculate the curves. The indicated speeds are applicable for operation without presence check. RF340R/ RF350R RF380R Operating distance (Sa) 22 mm 60 mm
RF300 system planning 4.4 Dependence of the volume of data on the transponder speed with ISO tags SIMATIC RF300 54 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 RF380T: Display of speed relative to data volume (read/write)           5)55)55)5$17%\WHYPV Figure 4-13 RF380T with RF340R/RF350R and RF380R 4.4 Dependence of the volume of data on the transponder speed with ISO tags The curves seen here show the relation between speed and data transfer volume for each transponder. They should make it easier to preselect the transponders for dynamic use. 4.4.1 MDS D100 with RF310R, RF340R/RF350R and RF380R The following table is used to calculate the curves. The indicated speeds are applicable for operation without presence check. RF310R RF340R/ RF350R RF380R Operating distance (Sa) 30 mm @ 30 mm
RF300 system planning 4.4 Dependence of the volume of data on the transponder speed with ISO tags SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 55 MDS D100: Display of speed relative to data volume (read/write) %\WHYPV5HDG5)55HDG5)5:ULWH5)5:ULWH5)5  Figure 4-14 MDS D100 with RF310R, RF340R/RF350R/ANT 12 and RF380R 4.4.2 MDS D124 with RF310R, RF340R/RF350R and RF380R The following table is used to calculate the curves. The indicated speeds are applicable for operation without presence check. RF310R RF340R/RF350R RF380R Operating distance (Sa) 25 mm 40 mm
RF300 system planning 4.4 Dependence of the volume of data on the transponder speed with ISO tags SIMATIC RF300 56 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 MDS D124: Display of speed relative to data volume (read/write) 5HDG5)55HDG5)5:ULWH5)5:ULWH5)5%\WHYPV  Figure 4-15 MDS D124 with RF310R, RF340R/RF350R and RF380R 4.4.3 MDS D139 with RF310R, RF340R/RF350R and RF380R The following table is used to calculate the curves. The indicated speeds are applicable for operation without presence check. RF340R/RF350R RF380R Operating distance (Sa) 60 mm
RF300 system planning 4.4 Dependence of the volume of data on the transponder speed with ISO tags SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 57 MDS D139: Display of speed relative to data volume (read/write) %\WHYPV5HDG5)5:ULWH5)5  Figure 4-16 MDS D139 with RF310R, RF340R/RF350R and RF380R 4.4.4 MDS D160 with RF310R, RF340R/RF350R and RF380R The following table is used to calculate the curves. The indicated speeds are applicable for operation without presence check. RF310R RF340R/RF350R RF380R Operating distance (Sa) 20 mm 40 mm
RF300 system planning 4.4 Dependence of the volume of data on the transponder speed with ISO tags SIMATIC RF300 58 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 MDS D160: Display of speed relative to data volume (read/write) %\WHYPV5HDG5)55HDG5)5:ULWH5)5:ULWH5)5  Figure 4-17 MDS D160 with RF310R, RF340R/RF350R and RF380R 4.4.5 MDS D324 with RF310R and RF380R The following table is used to calculate the curves. The indicated speeds are applicable for operation without presence check. RF310R RF340R/RF350R RF380R Operating distance (Sa) 20 mm 40 mm
RF300 system planning 4.4 Dependence of the volume of data on the transponder speed with ISO tags SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 59 MDS D324: Display of speed relative to data volume (read/write) %\WHYPV 0,000,200,400,600,801,001,201,401,601,802,00 ① Read RF380R ② Write RF380R ③ Read RF310R ④ Write RF310R Figure 4-18 MDS D324 with RF310R, RF340R/RF350R and RF380R 4.4.6 MDS D424 with RF310R, RF340R/RF350R and RF380R The following table is used to calculate the curves. The indicated speeds are applicable for operation without presence check. RF310R RF340R/RF350R RF380R Operating distance (Sa) 20 mm 40 mm
RF300 system planning 4.4 Dependence of the volume of data on the transponder speed with ISO tags SIMATIC RF300 60 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 MDS D424: Display of speed relative to data volume (read/write) 'XPP\'XPP\ Figure 4-19 MDS D424 with RF310R, RF340R/RF350R and RF380R 4.4.7 MDS D428 with RF310R, RF340R/RF350R and RF380R The following table is used to calculate the curves. The indicated speeds are applicable for operation without presence check. RF310R RF340R/RF350R RF380R Operating distance (Sa) 20 mm 40 mm
RF300 system planning 4.4 Dependence of the volume of data on the transponder speed with ISO tags SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 61 MDS D428: Display of speed relative to data volume (read/write) 'XPP\'XPP\ Figure 4-20 MDS D428 with RF310R, RF340R/RF350R and RF380R 4.4.8 MDS D460 with RF310R, RF340R/RF350R and RF380R The following table is used to calculate the curves. The indicated speeds are applicable for operation without presence check. RF310R RF340R/RF350R RF380R Operating distance (Sa) 20 mm 40 mm
RF300 system planning 4.5 Installation guidelines SIMATIC RF300 62 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 MDS D460: Display of speed relative to data volume (read/write) 'XPP\'XPP\ Figure 4-21 MDS D460 with RF310R, RF340R/RF350R and RF380R 4.5 Installation guidelines 4.5.1 Overview The transponder and reader complete with their antennas are inductive devices. Any type of metal, in particular iron and ferromagnetic materials, in the vicinity of these devices will affect their operation. Some points need to be considered during planning and installation if the values described in the "Field data" section are to retain their validity: ● Minimum spacing between two readers or their antennas ● Minimum distance between two adjacent data memories ● Metal-free area for flush-mounting of readers or their antennas and transponders in metal ● Mounting of multiple readers or their antennas on metal frames or racks The following sections describe the impact on the operation of the identification system when mounted in the vicinity of metal.
RF300 system planning 4.5 Installation guidelines SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 63 4.5.2 Reduction of interference due to metal Interference due to metal rack Problem 6KHHW0HWDOUDFN6D1RQPHWDOOLFVSDFHU0HWDO7UDQVSRQGHU5HDGHUV A metal rack is located above the transmission window of the reader. This affects the entire field. In particular, the transmission window between reader and transponder is reduced. Remedy: 7UDQVSRQGHU5HDGHU The transmission window is no longer affected if the transponder is mounted differently.
RF300 system planning 4.5 Installation guidelines SIMATIC RF300 64 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Flush-mounting Flush-mounting of transponders and readers Problem 1RQPHWDOOLFVSDFHU 6KHHW0HWDO0HWDO5HDGHUV Flush-mounting of transponders and readers is possible in principle. However, the size of the transmission window is significantly reduced. The following measures can be used to counteract the reduction of the window: Remedy: PP [!PP5HDGHU Enlargement of the non-metallic spacer below the transponder and/or reader. The transponder and/or reader are 10 to 20 mm higher than the metal surround. (The value x ≥ 100 mm is valid, e.g. for RF310R. It indicates that, for a distance x ≥ 100 mm, the reader can no longer be significantly affected by metal.) Remedy: DDEE5HDGHU Increase the non-metallic distance a, b. The following rule of thumb can be used:  Increase a, b by a factor of 2 to 3 over the values specified for metal-free areas  Increasing a, b has a greater effect for readers or transponders with a large limit distance than for readers or transponders with a small limit distance. Mounting of several readers on metal frames or racks Any reader mounted on metal couples part of the field to the metal frame. There is normally no interaction as long as the minimum distance D and metal-free areas a, b are maintained. However, interaction may take place if an iron frame is positioned unfavorably. Longer data transfer times or sporadic error messages at the communication module are the result.
RF300 system planning 4.5 Installation guidelines SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 65 Mounting of several readers on metal racks Problem: Interaction between readers Remedy '5HDGHU 5HDGHU Increase the distance D between the two readers. Remedy 5HDGHU 5HDGHU Introduce one or more iron struts in order to short-circuit the stray fields. Remedy 1RQPHWDOOLFVSDFHU5HDGHU 5HDGHU Insert a non-metallic spacer of 20 to 40 millimeter thickness between the reader and the iron frame. This will significantly reduce the induction of stray fields on the rack: 4.5.3 Effects of metal on different transponders and readers Mounting different transponders and readers on metal or flush-mounting Certain conditions have to be observed when mounting the transponders and readers on metal or flush-mounting. For more information, please refer to the descriptions of the individual transponders and readers in the relevant section.
RF300 system planning 4.5 Installation guidelines SIMATIC RF300 66 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 4.5.4 Impact on the transmission window by metal 4.5.4.1 Impact on the transmission window by metal In general, the following points should be considered when mounting RFID components: ● Direct mounting on metal is allowed only in the case of specially approved transponders. ● Flush-mounting of the components in metal reduces the field data; a test is recommended in critical applications. ● When working inside the transmission window, it should be ensured that no metal rail (or similar part) intersects the transmission field. The metal rail would affect the field data. The impact of metal on the field data (Sg, Sa, L, B) is shown in tabular format in this section. The values in the table describe the reduction of the field data in % with reference to non-metal (100% means no impact). 4.5.4.2 RF310R RF300 mode Table 4- 22 Reduction of field data by metal (in %): Transponder and RF310R RF310R reader Transponder Without metal On metal Flush-mounted In metal (20 mm all around) Without metal 100 95 80 On metal; distance 20 mm 100 80 70 RF320T Flush-mounted in metal; distance all-round 20 mm 80 70 60 Without metal 100 95 80 On metal 80 80 80 RF340T Flush-mounted in metal; distance all-round 20 mm 70 70 70 Without metal 100 95 85 On metal 70 65 65 RF350T Flush-mounted in metal; distance all-round 20 mm 60 60 60 Without metal 100 95 85 On metal; distance 20 mm 100 95 75 RF360T Flush-mounted in metal; distance all-round 20 mm 60 60 60
RF300 system planning 4.5 Installation guidelines SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 67 ISO mode Table 4- 23 Reduction of field data by metal (in %): Transponder and RF380R (ISO mode) RF310R reader (ISO mode) Transponder Without metal On metal Flush-mounted In metal (20 mm all around) Without metal 100 95 80 On metal; distance 20 mm 77 70 67 MDS D100 Flush-mounted in metal; distance all-round 20 mm 58 55 52 Without metal 100 98 82 On metal 93 94 87 MDS D124 Flush-mounted in metal; distance all-round 20 mm 82 76 60 Without metal 100 92 83 On metal; distance 20 mm 78 77 74 MDS D160 Flush-mounted in metal; distance all-round 20 mm 70 63 60 Without metal 100 95 76 On metal 83 81 78 MDS D324 Flush-mounted in metal; distance all-round 20 mm 79 76 72 Without metal On metal MDS D424 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D428 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D460 Flush-mounted in metal; distance all-round 20 mm
RF300 system planning 4.5 Installation guidelines SIMATIC RF300 68 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 4.5.4.3 RF340R RF300 mode Table 4- 24 Reduction of field data by metal (in %): Transponder and RF340R RF340R reader Transponder Without metal On metal Flush-mounted In metal (20 mm all around) Without metal 100 95 80 On metal; distance 20 mm 100 90 75 RF320T Flush-mounted in metal; distance all-round 20 mm 80 70 60 Without metal 100 95 85 On metal 80 80 70 RF340T Flush-mounted in metal; distance all-round 20 mm 70 70 70 Without metal 100 95 80 On metal 70 65 65 RF350T Flush-mounted in metal; distance all-round 20 mm 60 60 60 Without metal 100 95 85 On metal; distance 20 mm 90 90 75 RF360T Flush-mounted in metal; distance all-round 20 mm 70 60 60 Without metal 100 98 96 On metal 100 97 94 RF370T Flush-mounted in metal; distance all-round 20 mm 90 88 86 Without metal 100 86 76 (all-round 40 mm) On metal 100 86 76 (all-round 40 mm) RF380T Flush-mounted in metal; distance all-round 40 mm 83 71 55 (all-round 40 mm)
RF300 system planning 4.5 Installation guidelines SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 69 ISO mode Table 4- 25 Reduction of field data by metal (in %): Transponder and RF340R RF310R reader (ISO mode) Transponder Without metal On metal Flush-mounted In metal (20 mm all around) Without metal On metal; distance 20 mm MDS D100 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D124 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D139 Flush-mounted in metal; distance all-round 20 mm Without metal On metal; distance 20 mm MDS D160 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D324 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D424 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D428 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D460 Flush-mounted in metal; distance all-round 20 mm
RF300 system planning 4.5 Installation guidelines SIMATIC RF300 70 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 4.5.4.4 RF350R RF350R reader with ANT 1: RF300 mode Table 4- 26 Reduction of field data by metal (in %): Transponder and RF350R with ANT 1 RF350R reader Transponder Without metal On metal Flush-mounted In metal (20 mm all around) Without metal 100 95 80 On metal; distance 20 mm 100 90 75 RF320T Flush-mounted in metal; distance all-round 20 mm 80 70 60 Without metal 100 95 85 On metal 80 80 70 RF340T Flush-mounted in metal; distance all-round 20 mm 70 70 70 Without metal 100 95 80 On metal 70 65 65 RF350T Flush-mounted in metal; distance all-round 20 mm 60 60 60 Without metal 100 95 85 On metal; distance 20 mm 90 90 75 RF360T Flush-mounted in metal; distance all-round 20 mm 70 60 60 Without metal 100 86 73 On metal 100 83 69 RF370T Flush-mounted in metal; distance all-round 20 mm 90 74 61 Without metal 100 83 73 (all-round 40 mm) On metal 100 83 73 (all-round 40 mm) RF380T Flush-mounted in metal; distance all-round 40 mm 80 68 53 (all-round 40 mm)
RF300 system planning 4.5 Installation guidelines SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 71 RF350R reader with ANT 1: ISO mode Table 4- 27 Reduction of field data by metal (in %): Transponder and RF350R with ANT 1 RF310R reader (ISO mode) Transponder Without metal On metal Flush-mounted In metal (20 mm all around) Without metal On metal; distance 20 mm MDS D100 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D124 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D139 Flush-mounted in metal; distance all-round 20 mm Without metal On metal; distance 20 mm MDS D160 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D324 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D424 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D428 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D460 Flush-mounted in metal; distance all-round 20 mm
RF300 system planning 4.5 Installation guidelines SIMATIC RF300 72 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 RF350R reader with ANT 12: ISO mode Table 4- 28 Reduction of field data by metal (in %): Transponder and RF350R with ANT 12 RF310R reader (ISO mode) Transponder Without metal On metal Flush-mounted In metal (20 mm all around) Without metal On metal; distance 20 mm MDS D160 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D421Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D428Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D460Flush-mounted in metal; distance all-round 20 mm RF350R reader with ANT 18: RF300 mode Table 4- 29 Reduction of field data by metal (in %): Transponder and RF350R with ANT 18 Mounting the antenna Transponder Without metal Flush-mounted In metal (10 mm all-round; 10 mm deep) Without metal 100 100 On metal; distance 20 mm 100 100 RF320T Flush-mounted in metal; distance all-round 20 mm 80 80 Without metal 100 100 On metal 80 80 RF340T Flush-mounted in metal; distance all-round 20 mm 70 70
RF300 system planning 4.5 Installation guidelines SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 73 RF350R reader with ANT 18: ISO mode Table 4- 30 Reduction of field data by metal (in %): Transponder and RF350R with ANT 18 RF310R reader (ISO mode) Transponder Without metal On metal Flush-mounted In metal (20 mm all around) Without metal On metal MDS D124 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D160 Flush-mounted in metal; distance all-round 20 mm Without metal On metal; distance 20 mm MDS D324 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D421 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D424 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D428 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D460 Flush-mounted in metal; distance all-round 20 mm
RF300 system planning 4.5 Installation guidelines SIMATIC RF300 74 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 RF350R reader with ANT 30: RF300 mode Table 4- 31 Reduction of field data by metal (in %): Transponder and RF350R with ANT 30 Mounting the antenna Transponder Without metal Flush-mounted In metal (20 mm all-round; 20 mm deep) Without metal 100 80 On metal; distance 20 mm 100 80 RF320T Flush-mounted in metal; distance all-round 20 mm 100 80 Without metal 100 80 On metal 80 65 RF340T Flush-mounted in metal; distance all-round 20 mm 70 60 Without metal 100 80 On metal 70 60 RF350T Flush-mounted in metal; distance all-round 20 mm 65 55 RF350R reader with ANT 30: ISO mode Table 4- 32 Reduction of field data by metal (in %): Transponder and RF350R with ANT 30 RF310R reader (ISO mode) Transponder Without metal On metal Flush-mounted In metal (20 mm all around) Without metal On metal MDS D124 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D160Flush-mounted in metal; distance all-round 20 mm Without metal On metal; distance 20 mm MDS D324 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D424Flush-mounted in metal; distance all-round 20 mm
RF300 system planning 4.5 Installation guidelines SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 75 RF310R reader (ISO mode) Transponder Without metal On metal Flush-mounted In metal (20 mm all around) Without metal On metal MDS D428 Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D460 Flush-mounted in metal; distance all-round 20 mm 4.5.4.5 RF380R Reader RF380R-RF300 mode Table 4- 33 Reduction of field data by metal (in %): Transponder and RF380R (RF300 mode) Reader RF380R (RF300 mode) Transponder Without metal On metal Flush-mounted In metal (20 mm all around) Without metal 100 95 90 On metal; distance 20 mm 85 75 70 RF320T Flush-mounted in metal; distance all-round 20 mm 60 55 50 Without metal 100 90 80 On metal 70 65 60 RF340T Flush-mounted in metal; distance all-round 20 mm 63 60 55 Without metal 100 85 80 On metal 70 65 60 RF350T Flush-mounted in metal; distance all-round 20 mm 55 50 45 Without metal 100 95 85 On metal; distance 20 mm 75 70 65 RF360T Flush-mounted in metal; distance all-round 20 mm 60 55 50 Without metal 100 95 85 On metal 90 85 80 RF370T Flush-mounted in metal; distance all-round 20 mm 65 63 60
RF300 system planning 4.5 Installation guidelines SIMATIC RF300 76 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Reader RF380R (RF300 mode) Transponder Without metal On metal Flush-mounted In metal (20 mm all around) Without metal 100 95 85 On metal 95 90 80 RF380T Flush-mounted in metal; distance all-round 40 mm 65 60 58 RF380R reader: ISO mode Table 4- 34 Reduction of field data by metal (in %): Transponder and RF380R (ISO mode) Reader RF380R (ISO mode) Transponder Without metal On metal Flush-mounted In metal (20 mm all around) Without metal 100 95 80 On metal; distance 20 mm 65 62 58 MDS D100 Flush-mounted in metal; distance all-round 20 mm 58 53 48 Without metal 100 98 92 On metal 95 92 87 MDS D124 Flush-mounted in metal; distance all-round 20 mm 70 65 50 Without metal 100 92 75 MDS D139 On metal, distance 30 mm 93 88 72 Without metal 100 95 90 On metal; distance 20 mm 87 85 80 MDS D160 Flush-mounted in metal; distance all-round 20 mm 73 65 60 Without metal 100 95 85 On metal 85 83 80 MDS D324 Flush-mounted in metal; distance all-round 20 mm 70 65 60 Without metal On metal MDS D424Flush-mounted in metal; distance all-round 20 mm Without metal On metal MDS D428Flush-mounted in metal; distance all-round 20 mm
RF300 system planning 4.6 Chemical resistance of the transponders SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 77 Reader RF380R (ISO mode) Transponder Without metal On metal Flush-mounted In metal (20 mm all around) Without metal On metal MDS D460 Flush-mounted in metal; distance all-round 20 mm 4.6 Chemical resistance of the transponders 4.6.1 Chemical resistance of the RF300 transponders The following table provides an overview of the chemical resistance of the data memories made of glass-fiber-reinforced epoxy resin. It must be emphasized that the plastic enclosure is extremely resistant to chemicals in automobiles (e.g.: oil, grease, diesel fuel, gasoline) which are not listed separately. Transponders RF320T, RF360T Transponder RF 320T is resistant to the substances specified in the following table. Concentration 20 °C 40 °C 60 °C Allylchloride ￮￮￮￮ Formic acid 50 % ￮￮￮￮ 100 % ￮￮ Ammonia gas ￮￮￮￮ Ammonia liquid, water-free ￚ Ammonium hydroxide 10 % ￮￮￮￮ Ethyl acrylate ￮￮￮￮ Ethyl glycol ￮￮￮￮ Gasoline, aroma-free ￮￮￮￮ Gasoline, containing benzol ￮￮￮￮ Benzoate (Na–, Ca.a.) ￮￮￮￮ Benzoic acid ￮￮￮￮ Benzole ￮￮￮￮ Benzenesulphonic acid ￮￮￮￮ Benzyl chloride ￚ Borax ￮￮￮￮ Boric acid ￮￮￮￮ Bromine, liquid ￚ Bromine, gas, dry ￚ
RF300 system planning 4.6 Chemical resistance of the transponders SIMATIC RF300 78 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Concentration 20 °C 40 °C 60 °C Bromide (K–, Na.a.) ￮￮￮￮ Bromoform 100 % ￮￮￮￮ Bromine water ￚ Butadiene (1,3–) ￮￮￮￮ Butane gas ￮￮￮￮ Butanol ￚ Butyric acid 100 % ￮￮ Carbonate (ammonium, Na.a.) ￮￮￮￮ Chlorine, liquid ￚ Chlorine, gas, dry 100 % ￚ Chlorobenzene ￮￮￮￮ Chloride (ammonium, Na.a.) ￮￮￮￮ Chloroform ￚ Chlorophyl ￮￮￮￮ Chlorosulphonic acid 100 % ￚ Chlorine water (saturated solution) ￮￮ Chromate (K–, Na.a.) Up to 50 % ￮￮￮￮ Chromic acid Up to 30 % ￚ Chromosulphuric acid ￚ Citric acid ￮￮￮￮ Cyanamide ￮￮￮￮ Cyanide (K–, Na.a.) ￮￮￮￮ Dextrin, w. ￮￮￮￮ Diethyl ether ￮￮￮￮ Diethylene glycol ￮￮￮￮ Dimethyl ether ￮￮￮￮ Dioxane ￚ Developer ￮￮￮￮ Acetic acid 100 % ￮￮ Ethanol ￮￮￮￮ ￮￮￮￮ Fixer ￮￮￮￮ Fluoride (ammonium, K–, Na.a.) ￮￮￮￮ Hydrofluoric acid Up to 40 % ￮￮￮￮ Formaldehyde 50 % ￮￮￮￮ Formamide 100 % ￮￮￮￮ Glucon acid ￮￮￮￮ Glycerine ￮￮￮￮ Glycol ￮￮￮￮ Urine ￮￮￮￮ Uric acid ￮￮￮￮
RF300 system planning 4.6 Chemical resistance of the transponders SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 79 Concentration 20 °C 40 °C 60 °C Hydroxide (ammonium) 10 % ￮￮￮￮ Hydroxide (Na–, K–) 40 % ￮￮￮￮ Hydroxide (alkaline earth metal) ￮￮￮￮ Hypochlorite (K–, Na.a.) ￮￮￮￮ Iodide (K–, Na.a.) ￮￮￮￮ Silicic acid ￮￮￮￮ Cresol Up to 90 % ￚ Methanol 100 % ￮￮￮￮ Methylene chloride ￚ Lactic acid 100 % ￮￮ Mineral oils ￮￮￮￮ Nitrate (ammonium, K.a.) ￮￮￮￮ Nitroglycerine ￚ Oxalic acid ￮￮￮￮ Phenol 1 % ￮￮￮￮ Phosphate (ammonium, Na.a.) ￮￮￮￮ Phosphoric acid 50 % ￮￮￮￮ 85 % ￮￮￮￮ Propanol ￮￮￮￮ Nitric acid 25 % ￚ Hydrochloric acid 10 % ￚ Brine ￚ Sulphur dioxide 100 % ￮￮ Carbon disulfide 100 % ￚ Sulphuric acid 40 % ￚ Sulphurous acid ￮￮ Soap solution ￮￮￮￮ Sulfate (ammonium, Na.a.) ￮￮￮￮ Sulfite (ammonium, Na.a.) ￚ Tar, aroma-free ￮￮￮￮ Turpentine ￮￮￮￮ Trichloroethylene ￚ Hydrogen peroxide 30 % ￮￮￮￮ Tartaric acid ￮￮￮￮ Abbreviations ￮￮￮￮ Resistant ￮￮￮ Virtually resistant ￮￮ Partially resistant ￮ Less resistant
RF300 system planning 4.6 Chemical resistance of the transponders SIMATIC RF300 80 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Abbreviations ￚ Not resistant w. Aqueous solution k. g. Cold saturated Transponders RF340T, RF350T, 370T The following table gives an overview of the chemical composition of the data memories made from polyamide 12. The plastic housing has a notably high resistance to chemicals used in automobiles (e.g.: oil, grease, diesel fuel, gasoline) which are not listed separately. Concentration 20 °C 60 °C Battery acid 30 ￮￮ ￚ Ammonia gas ￮￮￮￮ ￮￮￮￮ Ammonia, w. conc. ￮￮￮￮ ￮￮￮￮ 10 ￮￮￮￮ ￮￮￮￮ Benzol ￮￮￮￮ ￮￮￮ Bleach solution (12.5% effective chlorine) ￮￮ ￚ Butane, gas, liquid ￮￮￮￮ ￮￮￮￮ Butyl acetate (acetic acid butyl ester) ￮￮￮￮ ￮￮￮￮ n(n) ￮￮￮￮ ￮￮￮ Calcium chloride, w. ￮￮￮￮ ￮￮￮ Calcium nitrate, w. k. g. ￮￮￮￮ ￮￮￮ Chlorine ￚ ￚ Chrome baths, tech. ￚ ￚ Iron salts, w. k. g. ￮￮￮￮ ￮￮￮￮ Acetic acid, w. 50 ￚ ￚ Ethyl alcohol, w., undenaturated 96 ￮￮￮￮ ￮￮￮ 50 ￮￮￮￮ ￮￮￮￮ Formaldehyde, w. 30 ￮￮￮ ￚ 10 ￮￮￮￮ ￮￮￮ Formalin ￮￮￮ ￚ Glycerine ￮￮￮￮ ￮￮￮￮ Isopropanol ￮￮￮￮ ￮￮￮ Potassium hydroxide, w. 50 ￮￮￮￮ ￮￮￮￮ Lysol ￮￮ ￚ Magnesium salts, w. k. g. ￮￮￮￮ ￮￮￮￮ Methyl alcohol, w. 50 ￮￮￮￮ ￮￮￮￮ Lactic acid, w. 50 ￮￮ ￚ 10 ￮￮￮ ￮￮ Sodium carbonate, w. (soda) k. g. ￮￮￮￮ ￮￮￮￮ Sodium chloride, w. k. g. ￮￮￮￮ ￮￮￮￮ Sodium hydroxide ￮￮￮￮ ￮￮￮￮ Nickel salts, w. k. g. ￮￮￮￮ ￮￮￮￮
RF300 system planning 4.6 Chemical resistance of the transponders SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 81 Concentration 20 °C 60 °C Nitrobenzol ￮￮￮ ￮￮ Phosphoric acid 10 ￮ V Propane ￮￮￮￮ ￮￮￮￮ Mercury ￮￮￮￮ ￮￮￮￮ Nitric acid 10 ￮ ￚ Hydrochloric acid 10 ￮ ￚ Sulphur dioxide Low ￮￮￮￮ ￮￮￮￮ Sulphuric acid 25 ￮￮ ￚ 10 ￮￮￮ ￚ Hydrogen sulphide Low ￮￮￮￮ ￮￮￮￮ Carbon tetrachloride ￮￮￮￮ ￮￮￮￮ Toluene ￮￮￮￮ ￮￮￮ Detergent High ￮￮￮￮ ￮￮￮￮ Plasticizer ￮￮￮￮ ￮￮￮￮ Abbreviations ￮￮￮￮ Resistant ￮￮￮ Virtually resistant ￮￮ Partially resistant ￮ Less resistant ￚ Not resistant w. Aqueous solution k. g. Cold saturated Transponder RF380T The housing of the heat-resistant data storage unit is made of polyphenylene sulfide (PPS). The chemical resistance of the data storage unit is excellent. No solvent is known that can dissolve the plastic at temperatures below 200 °C. A reduction in the mechanical properties has been observed in aqueous solutions of hydrochloric acid (HCl) and nitric acid (HNO3) at 80 °C. The excellent resistance to all fuel types including methanol is a particular characteristic. The following table provides an overview of the chemicals investigated. Test conditions Substance Time[days] Temperature[°C] Evaluation Acetone 180 55 + n-Butanol (butyl alcohol) 180 80 + Butanon-2 (methyl ethyl ketone) 180 60 + n-butyl acetate 180 80 + Brake fluid 40 80 + Calcium chloride (saturated) 40 80 + Diesel fuel 180 80 +
RF300 system planning 4.6 Chemical resistance of the transponders SIMATIC RF300 82 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Test conditions Substance Time[days] Temperature[°C] Evaluation Diethyl ether 40 23 + Frigen 113 40 23 + Anti-freeze 180 120 + Kerosine 40 60 + Methanol 180 60 + Engine oil 40 80 + Sodium chloride (saturated) 40 80 + Sodium hydroxide (30%) 180 80 + Sodium hypochlorite (5%) 30 80 / 180 80 – Caustic soda (30%) 40 93 + Nitric acid (10%) 40 23 + Hydrochloric acid (10%) 40 80 – Sulphuric acid (10%) 40 23 + (10%) 40 (30%) 40 Tested fuels: 40 80 + (FAM-DIN 51 604-A) 180 80 / Toluene 1, 1, 1-trichloroethane 180 80 + Xylene Zinc chloride (saturated) 180 80 / 180 75 + 180 80 + 40 80 + Assessment: + Resistant, weight gain < 3 % or weight loss < 0.5 % and/or reduction in fracture resistance < 15 % / Partially resistant, weight gain 3 to 8 % or weight loss 0.5 to 3 % and/or reduction in fracture resistance 15 to 30 % – Not resistant, weight gain > 8 % or weight loss > 3 % and/or reduction in fracture resistance > 30 % 4.6.2 Chemical resistance of the ISO transponders MDS D100, MDS D200 The housing of the MDS D100 is made of PVC. MDS D100 is resistant to the substances specified in the following table.
RF300 system planning 4.6 Chemical resistance of the transponders SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 83 Table 4- 35 Chemical resistance of MDS D100, MDS D200 Substance Concentration Saline solution 5 % Sugared water 10 % Acetic acid, aqueous solution 5 % Sodium carbonate, aqueous solution 5 % Ethanol, aqueous solution 60 % Ethylene glycol 50 % Fuel B according to ISO 1817 Human sweat (Reference: ISO 10373 / ISO 7810) MDS D139, MDS D124 The housing of the heat-resistant data storage unit MDS D139 is made of polyphenylene sulfide (PPS). The chemical resistance of the data storage unit is excellent. No solvent is known that can dissolve the plastic at temperatures below 200 °C. A reduction in the mechanical properties has been observed in aqueous solutions of hydrochloric acid (HCl) and nitric acid (HNO3) at 80 °C. The excellent resistance to all fuel types including methanol is a particular characteristic. The following table provides an overview of the chemicals investigated. Table 4- 36 Chemical resistance of MDS D139, MDS D124 Test conditions Substance Time [days] Temperature [°C] Evaluation Acetone 180 55 + n-Butanol (butyl alcohol) 180 80 + Butanon-2 (methyl ethyl ketone) 180 60 + n-butyl acetate 180 80 + Brake fluid 40 80 + Calcium chloride (saturated) 40 80 + Diesel fuel 180 80 + Diethyl ether 40 23 + Frigen 113 40 23 + Anti-freeze 180 120 + Kerosine 40 60 + Methanol 180 60 + Engine oil 40 80 + Sodium chloride (saturated) 40 80 + Sodium hydroxide (30 percent) 180 80 + Sodium hypochlorite (5 percent) 30 180 80 80 / - Caustic soda (30 percent) 40 93 +
RF300 system planning 4.6 Chemical resistance of the transponders SIMATIC RF300 84 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Test conditions Substance Time [days] Temperature [°C] Evaluation Nitric acid (10 percent) 40 23 + Hydrochloric acid (10 percent) 40 80 - Sulphuric acid (10 percent) (10 percent) (30 percent) 40 40 40 23 80 23 + / + Tested fuels: 40 80 + (FAM-DIN 51604-A) Toluol 180 80 / 1, 1, 1-trichloroethane xylene 180 80 + Zinc chloride (saturated) 180 180 180 40 80 75 80 80 / + + + Assessment: + Resistant, weight gain < 3 % or weight loss < 0.5 % and/or reduction in fracture resistance < 15 % / Limited resistance, weight gain 3 to 8 % or weight loss 0.5 to 3 % and/or reduction in fracture resistance 15 to 30 % - Not resistant, weight gain > 8 % or weight loss > 3 % and/or reduction in fracture resistance > 30 % MDS D324, MDS D421, MDS D424, MDS D460 The housing of the MDS D124 is made of epoxy casting resin. The following table provides an overview of the chemical resistance. Table 4- 37 Chemical resistance of MDS D324, MDS D421, MDS D424, MDS D460 Chemical compound Concentration 20 °C 40 °C 60 °C Formic acid 50 % ■ Ammonia liquid, water-free □ Ethanol ■ ■ Gasoline, aromatic-free/containing benzol ■ Benzol, benzoic acid ■ Borax ■ Boric acid ■ Bromine, liquid, bromine water □ Butyric acid 100 % ◪ Carbonate (ammonium, sodium, etc.) ■ Chlorine, liquid □ Chlorobenzene ■ Chloroform □
RF300 system planning 4.6 Chemical resistance of the transponders SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 85 Chemical compound Concentration 20 °C 40 °C 60 °C Chlorine water (saturated solution) ◪ Chromate (potassium, sodium, etc.) Up to 50 % ■ Chromic acid Up to 30 % □ Citric acid ■ Cyanide (potassium, sodium, etc.) ■ Diethylene glycol ■ Dioxane □ Acetic acid 100 % ◪ Fixer ■ Fluoride (ammonium, potassium, sodium, etc.) ■ Hydrofluoric acid Up to 40 % ■ Formaldehyde 50 % ■ Glycerine ■ Glycol ■ Urine, uric acid ■ Hydroxide (sodium, potassium) 40 % ■ Iodide (potassium, sodium, etc.) ■ Silicic acid ■ Methanol 100 % ■ Lactic acid 100 % ◪ Mineral oils ■ Nitrate (ammonium, potassium, etc.) ■ Nitroglycerine □ Phosphate (ammonium, sodium, etc.) ■ Phosphoric acid 50 % ■ Propanol ■ Hydrochloric acid, nitric acid 10 % □ Brine □ Sulphur dioxide 100 % ◪ Sulphuric acid 40 % □ Soap solution ■ Sulphate (ammonium, sodium, etc.) ■ Sulfide (ammonium, sodium, etc.) □ Turpentine ■ Trichloroethylene □ Hydrogen peroxide 30 % ■ Tartaric acid ■ Abbreviations: ■ Resistant ◪ Limited resistance □ Not resistant
RF300 system planning 4.7 EMC Directives SIMATIC RF300 86 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 MDS D160 The housing of the MDS D160 is made of PPA (polyphthalamide). The following table provides an overview of the chemical resistance. Table 4- 38 Chemical resistance of the MDS D160 Chemical compound Resistance Mineral lubricants ■ Aliphatic hydrocarbons ■ Aromatic hydrocarbons ■ Petroleum spirit ■ Weak mineral acids ■ Strong mineral acids ◪ Weak organic acids ■ Strong organic acids □ Oxidizing acids □ Weak alkalis ■ Strong alkalis ■ Trichlorethylene ■ Acetone ■ Alcohol ■ Abbreviations ■ Resistant ◪ Limited resistance □ Not resistant MDS D428 @ fehlt noch 4.7 EMC Directives 4.7.1 Overview These EMC Guidelines answer the following questions: ● Why are EMC guidelines necessary? ● What types of external interference have an impact on the system? ● How can interference be prevented? ● How can interference be eliminated? ● Which standards relate to EMC? ● Examples of interference-free plant design
RF300 system planning 4.7 EMC Directives SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 87 The description is intended for "qualified personnel": ● Project engineers and planners who plan system configurations with RFID modules and have to observe the necessary guidelines. ● Fitters and service engineers who install the connecting cables in accordance with this description or who rectify defects in this area in the event of interference. NOTICE Failure to observe notices drawn to the reader's attention can result in dangerous conditions in the plant or the destruction of individual components or the entire plant. 4.7.2 What does EMC mean? The increasing use of electrical and electronic devices is accompanied by: ● Higher component density ● More switched power electronics ● Increasing switching rates ● Lower power consumption of components due to steeper switching edges The higher the degree of automation, the greater the risk of interaction between devices. Electromagnetic compatibility (EMC) is the ability of an electrical or electronic device to operate satisfactorily in an electromagnetic environment without affecting or interfering with the environment over and above certain limits. EMC can be broken down into three different areas: ● Intrinsic immunity to interference: immunity to internal electrical disturbance ● Immunity to external interference: immunity to external electromagnetic disturbance ● Degree of interference emission: emission of interference and its effect on the electrical environment All three areas are considered when testing an electrical device. The RFID modules are tested for conformity with the limit values required by the CE and RTTE guidelines. Since the RFID modules are merely components of an overall system, and sources of interference can arise as a result of combining different components, certain guidelines have to be followed when setting up a plant.
RF300 system planning 4.7 EMC Directives SIMATIC RF300 88 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 EMC measures usually consist of a complete package of measures, all of which need to be implemented in order to ensure that the plant is immune to interference. Note The plant manufacturer is responsible for the observance of the EMC guidelines; the plant operator is responsible for radio interference suppression in the overall plant. All measures taken when setting up the plant prevent expensive retrospective modifications and interference suppression measures. The plant operator must comply with the locally applicable laws and regulations. They are not covered in this document. 4.7.3 Basic rules It is often sufficient to follow a few elementary rules in order to ensure electromagnetic compatiblity (EMC). The following rules must be observed: Shielding by enclosure ● Protect the device against external interference by installing it in a cabinet or housing. The housing or enclosure must be connected to the chassis ground. ● Use metal plates to shield against electromagnetic fields generated by inductances. ● Use metal connector housings to shield data conductors. Wide-area ground connection ● Bond all passive metal parts to chassis ground, ensuring large-area and low-HF-impedance contact. ● Establish a large-area connection between the passive metal parts and the central grounding point. ● Don't forget to include the shielding bus in the chassis ground system. That means the actual shielding busbars must be connected to ground by large-area contact. ● Aluminium parts are not suitable for ground connections. Plan the cable installation ● Break the cabling down into cable groups and install these separately. ● Always route power cables, signal cables and HF cables through separated ducts or in separate bundles. ● Feed the cabling into the cabinet from one side only and, if possible, on one level only. ● Route the signal cables as close as possible to chassis surfaces. ● Twist the feed and return conductors of separately installed cables.
RF300 system planning 4.7 EMC Directives SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 89 ● Routing HF cables: avoid parallel routing of HF cables. ● Do not route cables through the antenna field. Shielding for the cables ● Shield the data cables and connect the shield at both ends. ● Shield the analog cables and connect the shield at one end, e.g. on the drive unit. ● Always apply large-area connections between the cable shields and the shielding bus at the cabinet inlet and make the contact with clamps. ● Feed the connected shield through to the module without interruption. ● Use braided shields, not foil shields. Line and signal filter ● Use only line filters with metal housings ● Connect the filter housing to the cabinet chassis using a large-area low-HF-impedance connection. ● Never fix the filter housing to a painted surface. ● Fix the filter at the control cabinet inlet or in the direction of the source. 4.7.4 Propagation of electromagnetic interference Three components have to be present for interference to occur in a system: ● Interference source ● Coupling path ● Interference sink HJFRQQHFWLQJFDEOH,QWHUIHUHQFHVRXUFHGHYLFHHPLWWLQJLQWHUIHUHQFH&RXSOLQJSDWKHJGULYHXQLW HJUHDGHU,QWHUIHUHQFHVLQNGHYLFHDIIHFWHGE\LQWHUIHUHQFH Figure 4-22 Propagation of interference If one of the components is missing, e.g. the coupling path between the interference source and the interference sink, the interference sink is unaffected, even if the interference source is transmitting a high level of noise. The EMC measures are applied to all three components, in order to prevent malfunctions due to interference. When setting up a plant, the manufacturer must take all possible measures in order to prevent the occurrence of interference sources:
RF300 system planning 4.7 EMC Directives SIMATIC RF300 90 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 ● Only devices fulfilling limit class A of VDE 0871 may be used in a plant. ● Interference suppression measures must be introduced on all interference-emitting devices. This includes all coils and windings. ● The design of the system must be such that mutual interference between individual components is precluded or kept as small as possible. Information and tips for plant design are given in the following sections. Interference sources In order to achieve a high level of electromagnetic compatibility and thus a very low level of disturbance in a plant, it is necessary to recognize the most frequent interference sources. These must then be eliminated by appropriate measures. Table 4- 39 Interference sources: origin and effect Interference source Interference results from Effect on the interference sink Contacts System disturbances Contactors, electronic valves Coils Magnetic field Collector Electrical field Electrical motor Winding Magnetic field Contacts Electrical field Electric welding device Transformer Magnetic field, system disturbance, transient currents Power supply unit, switched-mode Circuit Electrical and magnetic field, system disturbance High-frequency appliances Circuit Electromagnetic field Transmitter (e.g. service radio) Antenna Electromagnetic field Ground or reference potential difference Voltage difference Transient currents Operator Static charge Electrical discharge currents, electrical field Power cable Current flow Electrical and magnetic field, system disturbance High-voltage cable Voltage difference Electrical field What interference can affect RFID? Interference source Cause Remedy Switched-mode power supply Interference emitted from the current infeed Replace the power supply Cable is inadequately shielded Better cable shielding Interference injected through the cables connected in series The reader is not connected to ground. Ground the reader
RF300 system planning 4.7 EMC Directives SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 91 Interference source Cause Remedy HF interference over the antennas caused by another reader  Position the antennas further apart.  Erect suitable damping materials between the antennas.  Reduce the power of the readers. Please follow the instructions in the section Installation guidelines/reducing the effects of metal Coupling paths A coupling path has to be present before the disturbance emitted by the interference source can affect the system. There are four ways in which interference can be coupled in: ,17(5)(5(1&(6,1.*DOYDQLFFRXSOLQJSDWK&DSDFLWLYHFRXSOLQJSDWK,QGXFWLYHFRXSOLQJSDWK5DGLDWLRQFRXSOLQJ5),'5HDGHU5),'5HDGHU5),'5HDGHU5),'5HDGHU,17(5)(5(1&(6285&( Figure 4-23 Ways in which interference can be coupled in When RFID modules are used, different components in the overall system can act as a coupling path:
RF300 system planning 4.7 EMC Directives SIMATIC RF300 92 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Table 4- 40 Causes of coupling paths Coupling path Invoked by Conductors and cables  Incorrect or inappropriate installation  Missing or incorrectly connected shield  Inappropriate physical arrangement of cables Control cabinet or housing  Missing or incorrectly wired equalizing conductor  Missing or incorrect earthing  Inappropriate physical arrangement  Components not mounted securely  Unfavorable cabinet configuration 4.7.5 Cabinet configuration The influence of the user in the configuration of an electromagnetically compatible plant encompasses cabinet configuration, cable installation, ground connections and correct shielding of cables. Note For information about electromagnetically compatible cabinet configuration, please consult the installation guidelines for SIMATIC PLCs. Shielding by enclosure Magnetic and electrical fields and electromagnetic waves can be kept away from the interference sink by using a metal enclosure. The easier the induced interference current can flow, the greater the intrinsic weakening of the interference field. All enclosures and metal panels in the cabinet should therefore be connected in a manner allowing good conductance. Figure 4-24 Shielding by enclosure
RF300 system planning 4.7 EMC Directives SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 93 If the control cabinet panels are insulated from each other, a high-frequency-conducting connection can be established using ribbon cables and high-frequency terminals or HF conducting paste. The larger the area of the connection, the greater the high-frequency conductivity. This is not possible using single-wire connections. Prevention of interference by optimum configuration Good interference suppression can be achieved by installing SIMATIC PLCs on conducting mounting plates (unpainted). When setting up the control cabinet, interference can be prevented easily by observing certain guidelines. Power components (transformers, drive units, load power supply units) should be arranged separately from the control components (relay control unit, SIMATIC S7). As a rule: ● The effect of the interference decreases as the distance between the interference source and interference sink increases. ● The interference can be further decreased by installing grounded shielding plates. ● The load connections and power cables should be installed separately from the signal cables with a minimum clearance of 10 cm. 3RZHUVXSSO\&&(8'ULYH6KLHOGSODWH Figure 4-25 Prevention of interference by optimum configuration
RF300 system planning 4.7 EMC Directives SIMATIC RF300 94 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 Filtering of the supply voltage External interference from the mains can be prevented by installing line filters. Correct installation is extremely important, in addition to appropriate dimensioning. It is essential that the line filter is mounted directly at the cabinet inlet. As a result, interference is filtered promptly at the inlet, and is not conducted through the cabinet. /LQHILOWHU,V&RUUHFW/LQHILOWHU,QFRUUHFW,F LQWHUIHUHQFHFXUUHQW,V Figure 4-26 Filtering of the supply voltage 4.7.6 Prevention of interference sources A high level of immunity to interference can be achieved by avoiding interference sources. All switched inductances are frequent sources of interference in plants. Suppression of inductance Relays, contactors, etc. generate interference voltages and must therefore be suppressed using one of the circuits below. Even with small relays, interference voltages of up to 800 V occur on 24 V coils, and interference voltages of several kV occur on 230 V coils when the coil is switched. The use of freewheeling diodes or RC circuits prevents interference voltages and thus stray interference on conductors installed parallel to the coil conductor.
RF300 system planning 4.7 EMC Directives SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 95 9DOYHV%UDNHV5HOD\FRLOV&RQWDFWRUV Figure 4-27 Suppression of inductance Note All coils in the cabinet should be suppressed. The valves and motor brakes are frequently forgotten. Fluorescent lamps in the control cabinet should be tested in particular. 4.7.7 Equipotential bonding Potential differences between different parts of a plant can arise due to the different design of the plant components and different voltage levels. If the plant components are connected across signal cables, transient currents flow across the signal cables. These transient currents can corrupt the signals. Proper equipotential bonding is thus essential. ● The equipotential bonding conductor must have a sufficiently large cross section (at least 10 mm2). ● The distance between the signal cable and the associated equipotential bonding conductor must be as small as possible (antenna effect). ● A fine-strand conductor must be used (better high-frequency conductivity). ● When connecting the equipotential bonding conductors to the centralized equipotential bonding strip (EBS), the power components and non-power components must be combined. ● The equipotential bonding conductors of the separate modules must lead directly to the equipotential bonding strip.
RF300 system planning 4.7 EMC Directives SIMATIC RF300 96 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 &DELQHW &DELQHW,QFRUUHFW3RZHUVXSSO\'ULYH'HYLFH3/&(%6'HYLFH'HYLFH,QFRUUHFW Figure 4-28 Equipotential bonding (EBS = Equipotential bonding strip) The better the equipotential bonding in a plant, the smaller the chance of interference due to fluctuations in potential. Equipotential bonding should not be confused with protective earthing of a plant. Protective earthing prevents the occurrence of excessive shock voltages in the event of equipment faults whereas equipotential bonding prevents the occurrence of differences in potential. 4.7.8 Cable shielding Signal cables must be shielded in order to prevent coupling of interference. The best shielding is achieved by installing the cables in steel tubes. However, this is only necessary if the signal cable is routed through an environment prone to particular interference. It is usually adequate to use cables with braided shields. In either case, however, correct connection is vital for effective shielding. Note An unconnected or incorrectly connected shield has no shielding effect. As a rule: ● For analog signal cables, the shield should be connected at one end on the receiver side ● For digital signals, the shield should be connected to the enclosure at both ends ● Since interference signals are frequently within the HF range (> 10 kHz), a large-area HF-proof shield contact is necessary
RF300 system planning 4.7 EMC Directives SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 97 Figure 4-29 Cable shielding The shielding bus should be connected to the control cabinet enclosure in a manner allowing good conductance (large-area contact) and must be situated as close as possible to the cable inlet. The cable insulation must be removed and the cable clamped to the shielding bus (high-frequency clamp) or secured using cable ties. Care should be taken to ensure that the connection allows good conductance. 5HPRYHSDLQW&DEOHWLH Figure 4-30 Connection of shielding bus The shielding bus must be connected to the PE busbar. If shielded cables have to be interrupted, the shield must be continued via the corresponding connector housing. Only suitable connectors may be used for this purpose.
RF300 system planning 4.7 EMC Directives SIMATIC RF300 98 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 6KLHOGWXUQHGXSVLGHGRZQWKURXJKrDQGFRQQHFWHGWRFRQQHFWRUKRXVLQJ5XEEHUVOHHYH Figure 4-31 Interruption of shielded cables If intermediate connectors, which do not have a suitable shield connection, are used, the shield must be continued by fixing cable clamps at the point of interruption. This ensures a large-area, HF-conducting contact.
SIMATIC RF300 System Manual, 11/2009 - Zwischenstand 17.09.2009, A5E01642529-04 99 Readers 5 Overview The reader ensures inductive communication with the transponders, and handles the serial connection to the communication modules or the 8xIQ-Sense module. Communication between the transponder and reader takes place over inductive alternating fields. The transmittable data volume between reader and transponder depends on: ● the speed at which the transponder moves through the transmission window of the reader. ● the length of the transmission window. ● the RF300 transponder type (FRAM, EEPROM). ● the use of ISO transponders ISO functionality With the following readers, you can also use ISO tags: ● SIMATIC RF310R reader (with RS422 interface) ● Reader SIMATIC RF340R ● Reader SIMATIC RF350R ● SIMATIC RF380R reader The readers must either be parameterized for the RF300 or ISO mode. The parameterization is done with the aid of the RESET message frame (INIT-Run). You can find more detailed information on the software parameterization in Product Information "FB 45 and FC 45 input parameters for RF300 and ISO transponders" (http://support.automation.siemens.com/WW/view/en/33315697) or the Function Manual FB 45 (http://support.automation.siemens.com/WW/view/en/21738808) from edition A3 onwards. Note ISO functionality is only possible with certain reader MLFBs. Only the SIMATIC RF310R and SIMATIC RF380R readers with the MLFB 6GT2801-xxBxx are suitable for operating with ISO tags.

Navigation menu