Sierra Wireless U598 USB Modem User Manual USB 598 Modem User Guide rev 1 1

Download:
Mirror Download [FCC.gov]
Document ID	1231048
Application ID	9h6Veh/3PDmn0c2v5aLR5w==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	41.77kB (522149 bits)
Date Submitted	2010-01-20 00:00:00
Date Available	2010-01-20 00:00:00
Creation Date	2010-01-20 14:37:02
Producing Software	Acrobat Distiller 9.2.0 (Windows)
Document Lastmod	2010-01-20 14:43:33
Document Title	USB 598 Modem User Guide (rev 1.1)
Document Creator	FrameMaker 8.0

USB 598 Modem with
User Guide (Windows)
2131176
Rev 1.1
USB 598 modem - User Guide
Important Notice
Due to the nature of wireless communications, transmission
and reception of data can never be guaranteed. Data may be
delayed, corrupted (i.e., have errors) or be totally lost.
Although significant delays or losses of data are rare when
wireless devices such as the Sierra Wireless modem are used in
a normal manner with a well‐constructed network, the Sierra
Wireless modem should not be used in situations where failure
to transmit or receive data could result in damage of any kind
to the user or any other party, including but not limited to
personal injury, death, or loss of property. Sierra Wireless
accepts no responsibility for damages of any kind resulting
from delays or errors in data transmitted or received using the
Sierra Wireless modem, or for failure of the Sierra Wireless
modem to transmit or receive such data.
Safety and Hazards
Do not operate the Sierra Wireless modem:
•
In areas where blasting is in progress
•
Where explosive atmospheres may be present
•
Near medical equipment
•
Near life support equipment, or any equipment that may
be susceptible to any form of radio interference. In such
areas, the Sierra Wireless modem MUST BE POWERED
OFF. The Sierra Wireless modem can transmit signals that
could interfere with this equipment.
Do not operate the Sierra Wireless modem in any aircraft,
whether the aircraft is on the ground or in flight. In aircraft, the
Sierra Wireless modem MUST BE POWERED OFF. When
operating, the Sierra Wireless modem can transmit signals that
could interfere with various onboard systems.
Note: Some airlines may permit the use of cellular phones while the
aircraft is on the ground and the door is open. The Sierra Wireless
modem may be used at this time.
The driver or operator of any vehicle should not operate the
Sierra Wireless modem while in control of a vehicle. Doing so
will detract from the driver or operatorʹs control and operation
of that vehicle. In some states and provinces, operating such
communications devices while in control of a vehicle is an
offence.
2131176
Preface
Limitation of
Liability
The information in this manual is subject to change without
notice and does not represent a commitment on the part of
Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES
SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL
DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL,
CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES
INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR
REVENUE OR ANTICIPATED PROFITS OR REVENUE
ARISING OUT OF THE USE OR INABILITY TO USE ANY
SIERRA WIRELESS PRODUCT, EVEN IF SIERRA WIRELESS
AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES OR THEY ARE
FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY.
Notwithstanding the foregoing, in no event shall Sierra
Wireless and/or its affiliates aggregate liability arising under or
in connection with the Sierra Wireless product, regardless of
the number of events, occurrences, or claims giving rise to
liability, be in excess of the price paid by the purchaser for the
Sierra Wireless product.
Patents
Portions of this product may be covered by some or all of the
following US patents:
5,515,013
5,629,960
5,845,216
5,847,553
5,878,234
5,890,057
5,929,815
6,169,884
6,191,741
6,199,168
6,339,405
6,359,591
6,400,336
6,516,204
6,561,851
6,643,501
6,653,979
6,697,030
6,785,830
6,845,249
6,847,830
6,876,697
6,879,585
6,886,049
6,968,171
6,985,757
7,023,878, 7,053,843
7,106,569
7,145,267
7,200,512
7,287,162
7,295,171
D442,170
D459,303
D559,256
D560,911
and other patents pending.
This product includes technology licensed from
QUALCOMM® 3G.
Manufactured or sold by Sierra Wireless Inc. or its Licensees
under one or more patents licensed from InterDigital Group.
Copyright
Document 2131176. Rev 1.1 Jan.10
©2010 Sierra Wireless. All rights reserved.
USB 598 modem - User Guide
Trademarks
AirCard and “Heart of the Wireless Machine” are registered
trademarks of Sierra Wireless. Watcher is a trademark of Sierra
Wireless, registered in the European Community.
Sierra Wireless, the Sierra Wireless logo, TRU‐Install,
TRU‐Locate, and the red wave design are trademarks of Sierra
Wireless.
Windows® is a registered trademark of Microsoft Corporation.
QUALCOMM® is a registered trademark of QUALCOMM
Incorporated. gpsOne is a trademark of QUALCOMM
Incorporated.
InstallShield® is a registered trademark of Macrovision Corpo‐
ration in the United States of America and/or other countries.
Other trademarks are the property of the respective owners.
Contact
Information
Sales Desk:
Phone: 1-604-232-1488
Hours: 8:00 AM to 5:00 PM Pacific Time
E-mail: sales@sierrawireless.com
Post: Sierra Wireless
13811 Wireless Way
Richmond, BC
Canada
V6V 3A4
Fax: 1-604-231-1109
Web: www.sierrawireless.com
Additional
information and
updates
For up‐to‐date product descriptions, documentation, appli‐
cation notes, firmware upgrades, troubleshooting tips, and
press releases, visit www.sierrawireless.com.
2131176
Table of Contents
Introducing the USB 598 modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Welcome. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Feature summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Wireless modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TRU-Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TRU-Locate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CDMA 3G services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Watcher auto-update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Additional features of the modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
System components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Your host computing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The USB modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The modem drivers and enabling software . . . . . . . . . . . . . . . . . . . . . . . .
CDMA service provider account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The CDMA wireless network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
11
12
12
12
13
Care and maintenance of your modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
The USB 598 software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Account activation and configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installing the modem and software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Removing the modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Using the USB extension cable and laptop clip . . . . . . . . . . . . . . . . . . . . . . . . 21
Document 2131176. Rev 1.1 Jan.10
USB 598 modem - User Guide
Using a microSD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Inserting the microSD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Removing the microSD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Account configuration procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Activation Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Manual activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Watcher Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Starting and closing Watcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Components of the Watcher window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Window controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Interpreting icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Minimized icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
GPS Monitor window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Online Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
LED operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Radio frequency and electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . 36
Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Important safety/compliance information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Information pertaining to OEM customers . . . . . . . . . . . . . . . . . . . . . . . . . 41
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
2131176
1: Introducing the USB 598 modem 1
•
•
•
•
•
Welcome
Feature summary
Package contents
System components
Care and maintenance
of your modem
Note: This document applies to you, only if your wireless device is the
USB 598 modem from Sierra Wireless.
Welcome
The Sierra Wireless USB 598 modem is a wireless USB modem
for cellular and PCS networks, and the GPS frequency band.
The modem enhances the functionality of your mobile
computing device by adding 2‐way messaging and high‐speed
mobile data in extended areas, compared to wireless local area
networks.
This modem allows you to do the following (subject to feature
availability), without using a wireline phone or network:
•
Connect to the Internet, VPN and corporate networks
•
Send and receive large e‐mail messages
•
Send and receive SMS messages
•
Use location‐based services
•
Conduct video‐conferencing
•
Access streaming, real‐time media
•
Play games online
Note: You can view this guide online or print it to keep on hand. If
you're viewing it online, simply click a topic in the Table of Contents, or
a page number in the Index, or any page reference or section
reference. (Most text that is blue is a clickable link.) The PDF
automatically displays the appropriate page.
Document 2131176. Rev 1.1 Jan.10
USB 598 modem - User Guide
Feature summary
Note: For step-by-step instructions to access features of the
modem, consult the online help
available with the Watcher®
software (page 34).
The USB modem is designed to provide a wide range of
capabilities using CDMA network technology. Implemen‐
tation of these features depends on the particular service
provider and account features you have chosen.
Some features described in this manual may not be supported
by your service provider or may not be available with your
network account. For details of the services and accounts
available, contact your service provider.
Wireless modem
Once installed and configured, the modem can connect to the
CDMA network automatically. You just insert the modem,
allow Watcher to autolaunch and authenticate your account on
the network, then launch your Internet browser (which you
can also configure in Watcher to launch automatically)—you’re
online!
Alternatively, you can make a high‐speed data connection
without running Watcher—simply by launching whatever
application you want to use (such as your web browser or
e‐mail application). For details, see the online help topic
“Autoconnect behaviour”.
The modem also allows you to dial up a modem (such as a
corporate server).
TRU-Install
TRU‐Install™ is a Sierra Wireless feature that installs the
necessary software and drivers the first time you insert the
modem into your computer. An installation CD is not
required.
TRU-Locate
With TRU‐Locate™, you can use location‐based services (GPS)
to query, for example, the network for information on points of
interest (POI) that are near your current location, or display
driving instructions.
Note: TRU-Locate is subject to feature availability.
2131176
Introducing the USB 598 modem
Your modem requires an unobstructed view of GPS satellites
(in the sky), and, like any other GPS device, might not perform
well within forested areas or near tall buildings.
Depending on your account, you may be charged for each
position fix or after you have performed a certain number of
fixes. For details, contact your service provider.
Depending on the mechanism that the network and your
modem use to obtain location information, GPS may not be
supported:
•
If Network Mode is set to “EVDO Only”
•
If youʹre roaming
•
If you do not have network coverage
•
Due to other reasons.
If you’re having problems using GPS, contact your service
provider.
CDMA 3G services
The modem operates over a type of wireless network called
CDMA (Code Division Multiple Access).
CDMA 3G technology provides a variety of connectivity
features, depending on your service provider and account:
•
1x‐EVDO Rev. A supports Internet connections with data
rates up to 3.1 Mbps (downlink from the network) and
1.8 Mbps (uplink to the network). Average data rates are
450‐800 Kbps (downlink from the network) and
300‐400 Kbps (uplink to the network). Actual speed
depends on the network conditions.
•
1x‐EVDO Rev. 0 supports Internet connections with data
rates up to 2.4 Mbps (downlink from the network) and
153 Kbps (uplink to the network). Average data rates are
400‐700 Kbps (downlink from the network) and
40‐80 Kbps (uplink to the network). Actual speed depends
on the network conditions.
•
1X supports Internet connections with data rates up to
153 Kbps. Actual speed depends on the network condi‐
tions.
Once the connection is established, you can open your browser
and connect to any web site that is accessible through the
Internet, or access other Internet services (such as e‐mail).
The connection is “active” when data transmission is
occurring. If data transmission stops for a period of time
(determined by the network), the connection becomes
dormant.
Document 2131176. Rev 1.1 Jan.10
USB 598 modem - User Guide
•
Circuit switched (dial‐up) data, using the earlier CDMA
IS‐95 specification, supports data connections to any dial‐
in service at rates up to 14.4 Kbps.
•
QNC (Quick Net Connect) provides a simplified way to
dial into an Internet connection (using circuit switched
data) where 3G (1xEV‐DO or 1X) high‐speed packet
service is not available.
•
SMS (Short Message Service) allows you to send and
receive short text messages using the modem.
Watcher auto-update
The auto‐update feature keeps your firmware, drivers and
Watcher software up‐to‐date. You can set your own prefer‐
ences for when updates are downloaded.
To configure the auto‐update feature:
and select Options.
1.
In Watcher, click the Menu button
2.
In the User Options window, select the Check for updates
field.
3.
From the drop‐down list, select how often Watcher should
check for updates.
4.
Click OK.
Additional features of the modem
Beyond the features of the CDMA network, the modem
provides additional software features:
•
PIN security code to protect your modem and account
from unauthorized use.
•
A wizard to assist with activating your CDMA account.
•
Sound options to customize ringtones for SMS messages.
•
A Call Log to track outgoing calls and determine the
amount of data transferred.
The modem has a microSD™ slot that can be used, with a
microSD card (sold separately), for file transfer or storage. For
more information, see “Using a microSD card” on page 22.
10
2131176
Introducing the USB 598 modem
Package contents
Your package contains the following items:
•
USB 598 modem
•
Quick Start Guide
•
USB extension cable
•
Laptop clip
•
Carrying pouch
•
Lanyard
Note: To meet FCC (regulatory) requirements, use only the supplied
USB extension cable and laptop clip; other cables and laptop clips
should not be used.
To install the modem drivers and software, you do not need an
installation CD. Your modem uses the Sierra Wireless
TRU‐Install feature. The drivers and software are installed
when you insert the modem into your computer and go
through the software installation; an installation CD is not
required.
System components
Your modem is just one part of a system designed to provide
you with a wide range of communication features. Every
component of the system is needed to enable these capabilities.
Your host computing device
Your notebook or desktop computer hosts the modem
hardware and runs the communication software: your web
browser or e‐mail application, and Watcher—the enabling
software for the modem.
You may also have other software on your computer that can
be used wirelessly with the modem, such as: file transfer appli‐
cations (FTP), chat or instant messaging, a VPN (Virtual
Private Network) client, client software for a corporate server
application.
Document 2131176. Rev 1.1 Jan.10
11
USB 598 modem - User Guide
The USB modem
The modem provides your computer with a connection to the
CDMA wireless network.
The modem fits into a USB slot available on most notebook
and desktop computers.
Every CDMA network operates on one of three radio
frequency bands. As a dual‐band product, the modem
operates on two of these bands (see page 36), providing a wide
coverage area.
The modem drivers and enabling
software
The modem drivers and enabling software (Watcher) monitor
and manage your wireless connections.
Your modem uses the Sierra Wireless TRU‐Install feature—the
drivers and software are installed when you insert the modem
into your computer.
The device driver software enables the modem to work with
your computer’s operating system.
Using the Watcher software, you can manage the modem and
monitor your connections.
For step‐by‐step instructions to access features of Watcher, use
the application’s online help.
CDMA service provider account
Companies that operate CDMA networks and provide access
to these networks are called service providers. To use the
modem, you must have an account with a CDMA service
provider.
Note: You can use the Lock
Modem feature to prevent others
from using your account, should
your modem be stolen.
Each service provider has its own pricing options. There may
be flat rate accounts, which provide you a maximum number
of minutes of network usage for a fixed monthly fee. There
may be accounts for which you are charged for network usage
by the minute or by the amount of data transmitted.
Your account may include a variety of other services such as
SMS messaging or location‐based services.
Each modem has been provisioned at the factory for use with a
particular service provider. This sets the modem to use
particular radio channels and enables services specific for that
provider.
12
2131176
Introducing the USB 598 modem
The process of setting up your account is called activation.
Activation involves action by the service provider and configu‐
ration of the modem.
The procedure to configure (activate) your modem is covered
in “Activation” on page 25.
The CDMA wireless network
Note: More information about
CDMA networks is available on
the CDMA Development Group
web site, www.cdg.org.
This is the worldwide infrastructure providing the radio
coverage that allows you to stay connected. Made up of radio
towers and a variety of network switches, routers, and servers,
the network is an interconnection of many service providers.
Note: Most service providers
have coverage maps on their
web sites.
There are CDMA networks that operate in the frequency bands
supported by the modem throughout North America and
parts of Latin America, Asia, and New Zealand. However,
each service provider operates a network that covers a limited
geographical area within the overall CDMA coverage area.
Note: The fee for service is
usually higher when you are
roaming (connecting to a
network other than the one
belonging to your service
provider).
Most service providers have “roaming” agreements with other
service providers, so that they can offer service outside of the
coverage area of their own networks. For example, assuming
you live in Vancouver (Canada), and travel frequently to
Seattle (United States), you can obtain an account with a
Vancouver service provider that has a roaming agreement with
a service provider in Seattle. You would then have local service
in Vancouver, and roaming service in Seattle.
Care and maintenance of your
modem
As with any electronic device, the modem must be handled
with care to ensure reliable operation. Follow these guidelines
in using and storing the modem:
Document 2131176. Rev 1.1 Jan.10
•
The modem should fit easily into your USB slot. Forcing
the modem into a slot may damage connector pins.
•
When inserting or removing the modem, always grip it by
the sides rather than the end.
•
Protect the modem from liquids, dust, and excessive heat.
•
When not installed in your computer, store the modem in
a safe place.
13
USB 598 modem - User Guide
14
2131176
2: Getting Started
• The USB 598 software
• Account activation and
configuration
Before you can begin using the modem, you must:
1.
Insert the modem, to install the enabling software and
drivers.
2.
Activate an account and configure the modem to use your
account (unless the modem has been pre‐activated).
This section provides an overview of this process.
The USB 598 software
The modem comes with the following software:
•
Watcher application that you use to manage the modem
and monitor your connections on your computer
•
The driver software that provides the interface between
the modem and your Windows operating system
Detailed instructions for installing the modem and its software
are provided in “Installation” on page 17.
Account activation and
configuration
To use the modem, you must have an account with a CDMA
service provider. The process of setting up an account is called
activation.
If you purchased the modem directly from a service provider,
you may already have an account; your modem may be pre‐
activated.
Otherwise, run the Watcher software and the Activation
Wizard, which guides you through the activation and configu‐
ration process. (Depending on your configuration, the
software and the activation procedure may start automati‐
cally.)
Configuring the modem involves setting the phone number
assigned by your service provider and may involve entering
other network parameters and settings such as a user name
and password to access services.
Document 2131176. Rev 1.1 Jan.10
15
USB 598 modem - User Guide
Your service provider may need to know:
•
The billing information to use to collect payment for your
network usage.
•
The ESN (Electronic Serial Number) or MEID (Mobile
Equipment Identifier) assigned to your modem during the
manufacturing process. (The ESN or MEID is printed on a
label on the modem and can be displayed in the software.)
This number is used to help authenticate your account
when you connect for service.
You require from your service provider:
16
•
An activation code that gives you access to configure the
account.
•
A phone number for your modem.
•
Additional information specific to your service provider
such as:
· A user ID (username) and password to authenticate your
network connection.
· A SID (System IDentifier) that identifies your home
network area and is used together with your phone
number to determine if you are “home” or “roaming”.
2131176
3: Installation
• System requirements
• Installing the modem
and software
• Removing the modem
• Using the USB
extension cable and
laptop clip
• Using a microSD card
This chapter guides you through the steps necessary to install
the modem on a notebook or desktop computer.
The basic steps are:
1.
Insert the modem into the USB slot to install the modem
drivers and software.
2.
If the modem has not been pre‐activated, use the
Activation Wizard to configure the modem (as described
in “Activation” on page 25).
Before you begin the installation process, ensure your
computer meets the requirements described below.
System requirements
The modem is supported on notebook and desktop computers
running:
•
Windows 7
•
Windows Vista
•
Windows XP (Home and Professional versions) with
Service Pack 2 or later
•
Windows 2000 with Service Pack 4 and Update Rollup 1
To install the modem, you require one USB slot.
Document 2131176. Rev 1.1 Jan.10
17
USB 598 modem - User Guide
Installing the modem and
software
Note: If you’re running Windows XP, you may require administrative
privileges, depending on the Windows XP installation.
If you’re running Windows 7, Windows Vista or Windows 2000, you
must be logged in with administrative privileges to install the modem
software.
If you’re running Windows 2000, your computer might be restarted, as
part of the installation process; save any open documents.
To install Watcher and the modem drivers:
Note: Do not forcefully insert the
modem. This may damage the
connector pins.
1.
If your computer has a WiFi or Bluetooth adapter, turn it
off. (For instructions, see the user guide or online Help of
your computer).
2.
Remove the protective cap from the USB connector of the
modem.
3.
Gently insert the modem into the USB slot. Alternatively:
· You can attach the USB extension cable (included in your
package) to your computer’s USB slot, connect the
modem and laptop clip to the USB extension cable, and
then attach the laptop clip to the top of your laptop’s
screen (see page 21 through page 22).
Note: If your computer’s USB slot is vertical, use the supplied USB
extension cable and laptop clip.
Do not insert the modem or the USB extension cable into a USB hub
or, if your keyboard is separate from your laptop, a USB slot on your
keyboard.
18
2131176
Installation
Warning: If the orientation of your computer’s USB slot or the
thickness of your computer are such that pressure is applied to the
modem’s end or side (as shown by the red circle in the drawing
below), you may damage the modem or your computer. In such
cases, do not insert the modem directly into your computer’s USB
slot; use the supplied USB extension cable and the supplied laptop
clip instead (see page 21).
4.
If the TRU‐Install window is not displayed, in Windows
Explorer browse to the
entry (under My
Computer), then browse to the Win folder and run Setup.exe;
alternatively, if you’re running Windows Vista and the
AutoPlay window is displayed, click Run setup.exe.
5.
In the TRU‐Install window, click OK.
6.
In the “Welcome to the InstallShield Wizard” window,
select Install to launch the InstallShield® Wizard.
7.
If the Open With... window appears, cancel the installation
(your computer is missing some files required for the
installation). Search for Instmsiw.exe (if you’re running
Windows 2000) among the downloads at
www.microsoft.com. Install the file on your computer,
remove the modem from your computer, then rerun the
installation.
8.
If the Ikernel Application Error window appears:
a) Cancel the installation.
b) Download the file:
http://support.installshield.com/kb/files/Q108312/
ikernelupdate.exe.
c) Install the file on your computer, remove the modem
from your computer (see page 20), then rerun the
installation.
9.
Document 2131176. Rev 1.1 Jan.10
Use the Next and Back buttons to navigate through the
wizard noting the following:
· To proceed with the installation, you must click I accept
the terms in the license agreement to indicate your accep‐
tance of the terms of the license agreement.
19
USB 598 modem - User Guide
Windows detects the modem and installs the drivers for it.
This may take a few minutes. Once completed, the system
tray may display the message “Your devices are ready to
use“ or “Your new hardware is installed and ready to use”:
10. If you are prompted to restart your computer:
a) Save any open documents.
b) Select the option to restart your computer.
c) Wait until your computer restarts and Windows is ready.
11. When you are notified that the installation is complete,
click Finish.
12. If Watcher has not started automatically, start it: double‐
click the Watcher icon
on your desktop.
13. Proceed to configure the modem to use your account (if it
was not pre‐activated). See “Activation” on page 25.
Removing the modem
To remove the modem:
1.
Close Watcher if it is open.
2.
If a microSD card is inserted into the modem, ensure
youʹve completed any file transfers.
3.
Click the Safely Remove Hardware icon in the system tray
to display the option to stop the device.
Windows Vista
20
Windows XP
Windows 2000
4.
Click the Safely remove USB Mass Storage Device entry
(Windows Vista or Windows XP) or Stop USB Mass Storage
Device and Stop Sierra Wireless USB 598 EVDO Network
Adapter entries (Windows 2000) for the modem.
5.
If a dialog box appears notifying you that it is safe to
remove the device, click OK.
6.
Pull the device out of the slot by gripping both sides of the
device and pulling the device straight out.
2131176
Installation
Using the USB extension cable
and laptop clip
Optionally, you can use the provided USB extension cable and
laptop clip. The laptop clip fits on top of your laptop screen
and holds your modem. This allows you to use your modem in
crowded spaces.
Note: To meet FCC (regulatory) requirements, use only the supplied
USB extension cable and laptop clip; other cables and laptop clips
should not be used.
To connect the USB extension cable and laptop clip:
1.
Remove the protective cap from the USB connector of the
modem.
2.
Slide the modem into the laptop clip.
3.
Connect the USB extension cable to the modem.
Modem
Laptop clip
USB extension cable
4.
Insert the other end of the USB extension cable into the
USB slot of your computer.
When the modem and the cable are properly connected,
the
Document 2131176. Rev 1.1 Jan.10
LED indicator is lit (blue, or blinking amber).
21
USB 598 modem - User Guide
5.
Place the laptop clip, with the modem in it, on top of your
laptop screen, as shown in the photo below.
Using a microSD card
Your computer recognizes the microSD card as a removable
storage device.
Note: If your microSD card has not been formatted, or is in a format
that your computer does not recognize, you will need to format the
microSD card before you can use it on your Windows computer. The
formatting procedure erases all the data on the microSD card, after
which the files CANNOT be retrieved. To prevent the loss of important
data, please check the contents before you format the microSD card.
The modem supports microSD cards up to 32 GB capacity.
Note: Using microSD cards larger than 32 GB can cause data loss
and damage your modem.
Inserting the microSD card
To insert the microSD card:
1.
Gently flip open the tab (labelled “microSD”) on the side
of the modem (1), as shown in the photo below.
22
2131176
Installation
2.
Hold the modem with the LEDs facing up.
3.
Gently insert the microSD card (label facing up—see the
above photo) into the slot on the side of the modem (2)
until the microSD card clicks into place.
Removing the microSD card
To remove the microSD card:
1.
Ensure youʹve completed any file transfers.
2.
Safely remove the hardware:
Windows Vista and Windows XP: Click the Safely
Remove Hardware icon (
in Windows Vista;
in Win‐
dows XP) in the system tray, and click the Safely remove
USB Mass Storage Device entry for the microSD card.
Windows 2000: Click the Safely Remove Hardware icon
in the system tray, and click the Stop USB Mass Storage
Device entry for the microSD card.
Document 2131176. Rev 1.1 Jan.10
3.
Using your fingernail or a thin blunt
object, gently press the microSD card in
and then release; it should partially pop
out of its slot, as shown in the photo.
4.
Remove the microSD card and store it in
a safe place.
5.
Close the tab over the microSD slot of the modem.
23
USB 598 modem - User Guide
24
2131176
4: Activation
• Account configuration
procedures
Account configuration
procedures
The final step to making the modem operational is configuring
it to use your CDMA service provider account. The process of
activation configures your modem with the required account
parameters (phone number, username, password, and so on).
If you purchased a pre‐activated modem, this step is not
necessary. Once the application software and drivers are
installed, the modem is ready for use. Proceed to “Watcher
Basics” on page 27.
Otherwise, you must either allow use the Activation Wizard to
activate and configure your account.
Activation Wizard
The Activation Wizard walks you through the process of
configuring an account. The process and options vary based on
the service provider.
This section is a guide only. Consult the Quick Start Guide,
and follow the directions on screen and instructions given by
your service provider representative.
If your modem does not have an activated account, and
Watcher has started automatically, then the Activation Wizard
should start automatically. If this does not happen:
1.
Ensure Watcher is running. If it is not, double‐click the
Watcher icon
on your desktop.
2.
Start the Activation Wizard: click the Menu button
select Activation Wizard.
and
3.
If the Automated Activation option is not available, select
Manual Activation and go to “Manual activation” on page 26.
4.
Select the Automated Activation option.
The activation progress is displayed in the Activation Wiz‐
ard window. If the process is successful, the window dis‐
plays “Activation successful”.
Document 2131176. Rev 1.1 Jan.10
25
USB 598 modem - User Guide
Note: If the window does not display “Activation successful”, retry the
process. If the process continues to fail, use manual activation (below)
or contact your service provider.
At this point your modem is ready to use.
Proceed to “Watcher Basics” on page 27.
Manual activation
Manual activation involves phoning your service provider,
exchanging information, and entering your account infor‐
mation into the appropriate fields in the wizard. (To use this
method, you require a phone.)
Use the Next and Back buttons to navigate through the wizard,
noting the following:
•
Prepare your billing information, before you phone the
service provider or proceed to the next window.
•
Contact your service provider. Inform your service
provider that you are activating a Sierra Wireless wireless
device. The representative will request your
ESN (Electronic Serial Number) or MEID. This is displayed
in the Activation Wizard (and is printed on the modem
box and on the label on the back of the modem).
•
As prompted by the wizard, enter the information
provided by the service representative.
•
Select Finish in the final window of the wizard.
On completion of the Activation Wizard, the modem is ready
for use. Proceed to “Watcher Basics” on page 27.
26
2131176
5: Watcher Basics
• Starting and closing
Watcher
• Components of the
Watcher Window
• Interpreting icons
• GPS Monitor window
• Online Help
• Warranty
• Troubleshooting
Watcher is the application that allows you to manage and
monitor the connection between the modem and the CDMA
network. You use Watcher to:
•
Determine your signal strength, roaming status, 3G high‐
speed data availability, and other network connection
parameters
•
Initiate and end data calls
•
Use location‐based services (subject to feature availability)
•
View call statistics
•
Receive and send SMS messages
•
Customize features and options
Depending on Watcher settings, you may be able to connect to
the CDMA network without starting Watcher—simply by
launching whatever application you want to use (such as your
web browser or e‐mail application); for details, see the online
help topic “Autoconnect behaviour”. However, Watcher and
its icon in the system tray won’t be available for you to monitor
the status of the connection. Location‐based services also won’t
be available.
Starting and closing Watcher
Depending on your settings in the Options window, Watcher
may launch automatically anytime you insert the modem. You
can also launch Watcher by:
•
Double‐clicking the Watcher icon
on your desktop
•
Selecting:
In Windows 7, Windows Vista or Windows XP: Start > All
Programs > Sierra Wireless > Watcher > Watcher;
In Windows 2000: Start > Programs > Sierra Wireless >
Watcher > Watcher.
Document 2131176. Rev 1.1 Jan.10
27
USB 598 modem - User Guide
The standard Windows control buttons in the upper right
corner of the window are used to minimize or close Watcher.
When minimized, Watcher does not appear as a taskbar
button. Instead, an icon is shown in the system tray, usually at
the right end of the taskbar. (See “Minimized icons” on
page 32.)
Components of the Watcher
window
The Watcher window has the following items, as shown in
Figure 5‐1:
•
Status indicators (see Table 5‐1 on page 29)
•
Menu button
•
Buttons to open various windows (these windows can also
be accessed by clicking the Menu button)
•
Connect/Disconnect button
•
Windows control buttons (in the top right corner)
Menu button
Minimize
button
Toggle Full/
Compact button
Close button
Status indicators
Connect/
Disconnect
button
Buttons to open
various windows
Status indicators
Figure 5-1: Watcher window
For a detailed description of the indicators and windows, see
the online help.
28
2131176
Watcher Basics
Window controls
•
The Minimize button closes the Watcher window but leaves
the application running. When Watcher is minimized, you
can use the Watcher icon in the system tray to determine
the modem status. (See “Minimized icons” on page 32.)
This icon replaces a taskbar button for Watcher.
Once minimized, you can redisplay the Watcher window
by doing one of the following:
· Clicking the Watcher icon in the system tray
· Double‐clicking the Watcher desktop shortcut
· Launching Watcher from the Start menu.
•
The Toggle Full/Compact button
is used to switch
between the full Watcher window and the compact view:
The compact view allows you to see connection status and
indicators while using less space on the desktop. If you
click the Menu button
, a menu is displayed. From this
menu you can open other Watcher windows and perform
various operations.
To return to full view, click the Toggle Full/Compact button
in the top right.
•
The Close button
is used to exit Watcher.
Interpreting icons
Watcher makes extensive use of icons to indicate status and
events. The various icons are described in the following table.
Table 5-1: Watcher icons
Icon
Meaning
Modem not detected.
You may be able to resolve this by doing one of the
following:
- Unlocking the modem (from the Menu button
select Unlock Modem)
- Powering the modem on (from the Menu button
select Turn Radio On)
- Ejecting the modem and re-inserting it
If this icon is still displayed, restart your computer.
Document 2131176. Rev 1.1 Jan.10
29
USB 598 modem - User Guide
Table 5-1: Watcher icons (continued)
Icon
Meaning
Modem detected but not connected to the network.
Modem detected and connected to the network.
The Signal Strength indicator uses bars to show the
intensity of the radio signal. The number of bars
increases as signal strength increases, to a maximum
of five bars.
When the indicator has an “X”, no connection is
possible, for one of these reasons:
• You are outside the CDMA network coverage
area
• The signal strength is too weak
• A network or account problem is preventing the
modem from obtaining service
Coverage. This icon indicates the types of service that
are currently available. A shaded area indicates this
type of service is not available.
For example, the icon at the left means 1X service is
not available, but EVDO is available.
The ToolTip shows the types of coverage available (for
example, EVDO Rev. 0 or Rev. A).
or
or
or
Fastest service available. The icons indicates the
fastest service that is:
• Available in your current coverage area
• Supported by your modem
The ToolTip shows the types of coverage available.
When the indicator has a dark background and no
white border, you have acquired service (but have not
established a data connection).
When the indicator has a white border around it, you
have a data connection on the wireless service.
When the indicator has a white background, the
network connection is dormant. (You are connected,
but there is currently no traffic.)
30
2131176
Watcher Basics
Table 5-1: Watcher icons (continued)
Icon
Meaning
The Roaming Status indicator shows whether you are
roaming onto the network of a service provider other
than your own.
When the indicator is off (gray), you are within the
local coverage area of your service provider. When
the indicator is on (solid black), you are roaming.
Your coverage area and account charges depend
upon your service provider and the type of account
you have.
There may be surcharges for roaming service.
If there is no roaming agreement between your
service provider and the local carrier, you may be
unable to establish data connections and use other
features.
Location-based services may not be available
(depending on the settings of your device, the
mechanism that the network and your device use to
obtain location information, and other factors).
The SMS message indicator shows whether you have
unread messages. A blinking icon indicates that there
are one or more urgent or important unread
messages.
To display the SMS Express window (in which the
messages are displayed), double-click the icon, or
click the SMS Express button
, or from the Menu
button select SMS Express.
If you position the mouse pointer over the GPS icon,
the ToolTip shows the GPS status (on or off).
Double-click the icon to open the GPS Monitor window
(page 32).
(Network operator dependent; this icon may not be
displayed.)
Document 2131176. Rev 1.1 Jan.10
31
USB 598 modem - User Guide
Minimized icons
Watcher displays an icon in the Windows system tray (which
is usually located in the lower right corner of your screen). The
system tray icon indicates your connection status or notifies
you when you have SMS messages.
Table 5-2: System tray icons
Icon
Meaning
Watcher cannot detect the modem. Ensure that the
modem is powered on, not locked, and properly
connected to your computer.
You are in service on the network but have no active data
connection.
The number of red bars indicates the signal strength.
You have an active data connection.
The number of green bars indicates the signal strength.
You have a new SMS message.
Only one icon can be displayed at a time. The priority of icons,
from highest to lowest, is:
•
No modem detected
•
SMS message(s)
•
Active or inactive connection.
For example, if you have unread SMS messages, and then
establish a data connection, the icon still displays as an unread
SMS message.
GPS Monitor window
The GPS Monitor window reports GPS data from your
modem.
32
2131176
Watcher Basics
The modem must have a fix on at least four satellites to report
latitude, longitude, altitude, velocity and heading. (The status
bar at the bottom of the GPS Monitor window indicates how
many satellites are being tracked.)
To open the GPS Monitor window, in Watcher:
1.
Click the Menu button
and select Display GPS.
‐ or ‐
Click the Display GPS button
‐ or ‐
Double‐click the GPS icon
in the main Watcher
window (network operator dependent; this icon may not
be available).
The GPS Monitor window reports:
•
Longitude and Latitude — your coordinates in degrees,
minutes, and seconds.
•
Direction — your direction in degrees from true north (0),
increasing clockwise.
•
Speed — calculated based on your current latitude and
longitude and the last reading (one second previous). This
is either in kilometers per hour or miles per hour,
depending on your chosen option.
•
Updated — date/time that the GPS values were last
acquired. The display format is based on your Control
Panel settings in Windows.
•
GPS port — port used for GPS activity.
•
Altitude — your altitude relative to mean sea level, in
either feet or meters, depending on your chosen option.
•
HEPE — Horizontal Estimated Position Error. Reflects
accuracy (horizontal/vertical precision).
From the GPS Monitor window you can:
•
Determine the number of satellites being tracked
•
Get your current location
•
View a map of your current location
•
Start/stop a tracking session
•
Configure GPS settings
For detailed information on using GPS and configuring the
settings, see the online Help of GPS Monitor.
Document 2131176. Rev 1.1 Jan.10
33
USB 598 modem - User Guide
Online Help
The Watcher and GPS Monitor applications include extensive
online help to provide operating hints and step‐by‐step
instructions for getting the most from your modem.
You can access online help in several ways:
•
Press  in any window.
•
In Watcher, click the Menu button
and select Help
Topics, or click the Help Topics button
(displays the
online Help of Watcher).
•
Use Windows Explorer to navigate to Program Files >
Sierra Wireless Inc > Watcher > Help, and double‐click
Watcher_ENU.chm (for Watcher help) or GPS_ENU.chm (for
GPS Monitor help).
The help files have a table of contents, an index, and search
capabilities.
Warranty
You can access a PDF of the warranty, in:
•
Windows 7, Windows Vista or Windows XP: Start > All
Programs > Sierra Wireless > Watcher
•
Windows 2000: Start > Programs > Sierra Wireless > Watcher
Troubleshooting
The online help includes descriptions of most common error
messages. Look in the table of contents under Troubleshooting.
For help with other problems:
34
•
Consult the Sierra Wireless web site at
www.sierrawireless.com, where you will find an extensive
knowledge base that can be searched to address most
problems.
•
Contact your service provider.
2131176
6: Technical Specifications
• LED operation
• Radio frequency and
electrical
specifications
• Environmental
specifications
This chapter describes the function of the LEDs, and provides
technical product data for the modem.
LED operation
The modem has two LED lights. The LEDs operate as follows:
Table 6-1: LED operation
LED
State
Indicates
Off
The modem has no power, or the LED has been disabled through the
software.
Check whether any of the following apply:
• You have powered off the modem.
• The modem is not completely inserted into the USB slot.
• The computer is in suspend mode, which powers down the
modem.
• You have set Disable LED (in the General pane of the User
Options window) to “Yes” (subject to feature availability).
Blue, not
blinking
The modem has power and is working properly.
Blue,
blinking
The modem’s firmware is being updated. Do not remove the modem.
Amber,
blinking
The modem is searching for service.
If this LED state persists:
• Ensure the modem is properly connected to your computer.
• If you are inside a building or near a structure that may be blocking
the signal, change the position or location of your computer.
• Ensure you are within the CDMA network coverage area. For
coverage information, contact your service provider.
• Check with your service provider—a network or account problem
may be preventing the wireless device from obtaining service.
Amber, not
blinking
An error has occurred. Remove the modem (page 20) and reinsert it.
Document 2131176. Rev 1.1 Jan.10
35
USB 598 modem - User Guide
Table 6-1: LED operation (continued)
LED
State
Indicates
Off
No service is available.
See the suggestions for “Amber, blinking” on page 35.
Amber,
blinking
1X coverage is detected. Ready to connect to the network (click
Connect).
Amber, not
blinking
The modem is connected to the 1X network, and can send or receive
data.
Blue,
blinking
1x-EVDO coverage (Rev. 0 or Rev. A) is detected. Ready to connect to
the network (click Connect).
Blue, not
blinking
The modem is connected to the 1x-EVDO network, and can send or
receive data.
Radio frequency and electrical
specifications
Table 6-2: Radio frequency and electrical
specifications
36
Approvals
Compliant with:
IS-2000 Release 1.0 (CDMA 1X)
IS-707-A Data, IS-856 (CDMA 1x-EVDO), IS-866,
IS-878, IS-890, CDMA Development Group
FCC
Industry Canada
Voltage
+5.0 Vdc from USB slot
Current
Maximum: 650 mA (from USB port)
Typical data call current (talk mode):
300 mA (1X)
390 mA (1xEV-DO)
Standby:
55 mA (1xEV-DO/IS2000 hybrid
mode)
Transmitter
power
250 mW (+24 dBm) average
Transmit
PCS:
1850 to 1909.95 MHz
Cellular: 824.04 to 848.97 MHz
Receive
PCS:
1930 to 1989.95 MHz
Cellular: 869.04 to 893.97 MHz
GPS:
1575.42 MHz
Channel
spacing
1.25 MHz
Frequency
stability
±150 Hz
2131176
Technical Specifications
Environmental specifications
Table 6-3: Environmental specifications
Document 2131176. Rev 1.1 Jan.10
Operating
temperature
-20 to +55°C
Storage
temperature
-40 to +85°C
Humidity
95%, non-condensing
Vibration
Random vibration, 10 to 1000 Hz, nominal 6G
RMS in each of 3 mutually perpendicular axes.
Test duration of 60 minutes for each axis, for a
total test time of 3 hours (non-operating).
Drop
1 m on concrete on each of 6 faces, 2 times
37
USB 598 modem - User Guide
38
2131176
7: Regulatory Information
• Important safety/
compliance
information
Important safety/compliance
information
Note: This USB modem is approved for use in normal-size laptop
computers only (typically with 12" or larger display screens). To
comply with FCC RF exposure requirements, this modem should not
be used in configurations that cannot maintain at least 12 mm (~0.5")
from users and bystanders. For example, this modem should not be
used in certain laptop and tablet computers and configurations where
the USB connectors are unable to provide or ensure the necessary
separation is available between the modem and its users to satisfy
compliance.
The design of the USB 598 modem complies with U.S. Federal
Communications Commission (FCC) and Industry Canada
(IC) guidelines respecting safety levels of radio frequency (RF)
exposure for portable devices, which in turn are consistent
with the following safety standards previously set by
Canadian, U.S. and international standards bodies:
•
ANSI / IEEE C95.1‐1999, IEEE Standard for Safety Levels with
Respect to Human Exposure to Radio Frequency Electromag‐
netic Fields, 3kHz to 300 GHz
•
National Council on Radiation Protection and Measure‐
ments (NCRP) Report 86, ‐1986, Biological Effects and
Exposure Criteria for Radio Frequency Electromagnetic Fields
•
Health Canada, Safety Code 6, 1999, Limits of Human
Exposure to Radio frequency Electromagnetic Fields in the
Frequency Range from 3 kHz to 300 GHz
•
International Commission on Non‐Ionising Radiation
Protection (ICNIRP) 1998, Guidelines for limiting exposure to
time‐varying electric, magnetic, and electromagnetic fields (up
to 300 GHz)
FCC ID: N7NU598.
CAUTION: The USB 598 modem must be 1.2 cm or more from
users during operation, to satisfy FCC RF exposure require‐
ments. The USB 598 modem has been tested for compliance
with FCC / IC RF exposure limits in the laptop computer(s)
configurations with horizontal and vertical USB slots and can
be used in laptop computers with substantially similar
physical dimensions, construction, and electrical and RF
characteristics. This USB modem must not be used with any
Document 2131176. Rev 1.1 Jan.10
39
USB 598 modem - User Guide
other antenna or transmitter that has not been approved to
operate in conjunction with this modem. Note: This USB
modem must not be used in any unapproved configurations.
For details, contact Sierra Wireless.
WARNING: If the orientation of your computer’s USB slot or
the thickness of your computer are such that pressure is
applied to the modem’s end or side, you may damage the
modem or your computer. In such cases, do not insert the
modem directly into your computer’s USB slot; use the
supplied laptop clip and USB extension cable instead.
WARNING (EMI) - United States FCC Information ‐ This device
complies with Part 15.19(a) (3) of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15.105(b) of
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential instal‐
lation.
This equipment generates, uses, and can radiate radio
frequency energy. If not installed and used in accordance with
the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that inter‐
ference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the distance between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician
for help.
WARNING (EMI) - Canada ‐ This digital apparatus does not
exceed the Class B limits for radio noise emissions from digital
apparatus as set out in the interference causing equipment
standard entitled ʺDigital Apparatusʺ, ICES‐003 of the
Department of Communications.
40
2131176
Regulatory Information
Cet appareil numérique respecte les limites de bruits radioélec‐
triques applicables aux appareils numériques de Classe B
prescrites dans la norme sur le matériel brouilleur: ʺAppareils
Numériquesʺ, NMB‐003 édictée par le ministre des Communi‐
cations.
If you have purchased this product under a United States
Government contract, it shall be subject to restrictions as set
forth in subparagraph (c)(1)(ii) of Defense Federal Acquisitions
Regulations (DFARs) Section 252.227‐7013 for Department of
Defense contracts, and as set forth in Federal Acquisitions
Regulations (FARs) Section 52.227‐19 for civilian agency
contracts or any successor regulations. If further government
regulations apply, it is your responsibility to ensure
compliance with such regulations.
Information pertaining to OEM customers
The USB 598 modem has been granted modular approval for
mobile applications. Integrators may use the USB 598 modem
in their final products without additional FCC / IC certification
if they meet the following conditions. Otherwise, additional
FCC / IC approvals must be obtained.
1.
At least 20 cm separation distance between the antenna
and the user’s body must be maintained at all times.
2.
To comply with FCC / IC regulations limiting both
maximum RF output power and human exposure to RF
radiation, the maximum antenna gain including cable loss
in a mobile‐only exposure condition must not exceed
2.4 dBi in the cellular band and 2.0 dBi in the PCS band.
3.
The USB 598 modem and its antenna must not be
co‐located or operating in conjunction with any other
transmitter or antenna within a host device.
4.
A label must be affixed to the outside of the end product
into which the USB 598 modem is incorporated, with a
statement similar to the following:
This device contains FCC ID: N7NU598.
This equipment contains equipment certified under IC:
2417C-U598.
5.
A user manual with the end product must clearly indicate
the operating requirements and conditions that must be
observed to ensure compliance with current FCC / IC RF
exposure guidelines.
The end product with an embedded USB 598 modem may also
need to pass the FCC Part 15 unintentional emission testing
requirements and be properly authorized per FCC Part 15.
Document 2131176. Rev 1.1 Jan.10
41
USB 598 modem - User Guide
Note: If this modem is intended for use in a portable device, you are
responsible for separate approval to satisfy the SAR requirements of
FCC Part 2.1093.
42
2131176
Appendix A: Glossary
1X
One Times Radio Transmission Technology (the ʺone timesʺ
refers to the frequency spectrum). Supports Internet
connections with data rates up to 153 Kbps. Actual speed
depends on the network conditions. Compare to 1x‐EVDO.
1x-EVDO
A high‐speed standard for cellular packet data communica‐
tions.
Rev. A supports Internet connections with data rates up to
3.1 Mbps (downlink from the network) and 1.8 Mbps (uplink
to the network).
Rev. 0 supports Internet connections with data rates up to
2.4 Mbps (downlink from the network) and 153 Kbps (uplink
to the network).
Average data rates are: for Rev. A: 450–800 Kbps (downlink
from the network) and 300–400 Kbps (uplink to the network);
for Rev. 0: 400‐700 Kbps (downlink from the network) and
40‐80 Kbps (uplink to the network).
Actual speed depends on the network conditions. Compare to
1X.
bps
CDMA
CDMA 1X
dormant
ESN
Document 2131176. Rev 1.1 Jan.10
bits per second—The actual data speed over the transmission
medium.
Code Division Multiple Access—A wideband spread spectrum
technique used in digital cellular, personal communications
services, and other wireless networks. Wide channels
(1.25 MHz) are obtained through spread spectrum transmis‐
sions, thus allowing many active users to share the same
channel. Each user is assigned a unique digital code, which
differentiates the individual conversations on the same
channel.
Also known as 1X, this is a high‐speed standard for CDMA
cellular communications.
The packet data connection has the logical PPP session left
open while the underlying physical link (the radio channel) is
released. When traffic is to resume, a radio channel is
re‐acquired and the original PPP session resumes.
Electronic Serial Number—The unique first‐generation serial
number assigned to the modem for cellular network use.
Compare to MEID.
43
USB 598 modem - User Guide
FCC
Federal Communications Commission—The U.S. federal
agency that is responsible for interstate and foreign communi‐
cations. The FCC regulates commercial and private radio
spectrum management, sets rates for communications services,
determines standards for equipment, and controls broadcast
licensing. Consult www.fcc.gov.
firmware
Software stored in ROM or EEPROM; essential programs that
remain even when the system is turned off. Firmware is easier
to change than hardware but more permanent than software
stored on disk.
GPS
Global Positioning System—A system that uses a series of 24
geosynchronous satellites to provide navigational data.
host
•
A computer that uses a modem or a similar device to
answer a calling computer.
•
A source or destination in the communication network.
•
A computer that contains data or files to be accessed by
client computers. Also known as a server.
IS
IS-95
The standard for CDMA.
Kbps
Kilobits per second—Actually 1000, not 1024, as used in
computer memory size measurements of kilobytes.
LAN
Local Area Network
LED
Light Emitting Diode—A semiconductor diode that emits
visible or infrared light.
MEID
Mobile Equipment Identifier—The unique second‐generation
serial number assigned to the modem for cellular network use.
Compare to ESN.
Mbps
Megabits per second
MHz
Mega‐Hertz—One million cycles per second.
packet
A short fixed‐length block of data, including a header, that is
transmitted as a unit in a communications network.
PCS
Personal Communications Services—A cellular
communication infrastructure that uses a different frequency
range than AMPS.
roaming
44
Interim Standard—After receiving industry consensus, the TIA
forwards the standard to ANSI for approval.
A cellular subscriber is in an area where service is obtained
from a cellular service provider that is not the subscriber’s
provider.
2131176
Glossary
SMS
system tray
TIA
VPN
Document 2131176. Rev 1.1 Jan.10
Short message services—A feature that allows users of a
wireless device on a wireless network to receive or transmit
short electronic alphanumeric messages (up to 160 characters,
depending on the service provider).
Usually located in the lower right corner of your screen
Telecommunications Industry Association—A standards‐
setting trade organization, whose members provide
communications and information technology products,
systems, distribution services and professional services in the
United States and around the world. Consult www.tiaonline.org.
Virtual Private Network
45
USB 598 modem - User Guide
46
2131176
Index
Numerics
1X
description, 9
icon, 30
LED ‐ coverage is detected, 36
1x‐EVDO
description, 9
icon, 30
LED ‐ coverage is detected, 36
3G
description, 9
contact information, 4
coverage
description, 13
indicator, 30
CSD (circuit switched data)
description, 10
current location
get, 33
map of, 33
data
account
configuration, 25
activation
automated, 25
manual, 26
altitude, 33
approvals, 36
automated activation, 25
auto‐update, 10
bands, frequency, 12
cable, USB extension, 21
care and maintenance, 13
CDMA 1X
description, 9
icon, 30
LED ‐ coverage is detected, 36
CDMA 1x‐EVDO
description, 9
icon, 30
LED ‐ coverage is detected, 36
CDMA network
3G services, 9
frequency bands, 12
service providers, 12
Check for updates, 10
circuit switched data (CSD)
description, 10
close button, 29
compact view, 29
connection status
Watcher, 30
Windows (indicator in system tray), 32
Rev 1.1 Jan.10
circuit switched ‐ description, 10
dial‐up ‐ description, 10
high‐speed, 9
QNC, 10
dial‐up data
description, 10
direction, 33
dormant, 30
drivers
description, 12
updates, check for, 10
driving instructions, 8
drop test, 37
electrical specifications, 36
Electronic Serial Number (ESN)
description, 16
EMI warning, 40
environmental specifications, 37
ESN (Electronic Serial Number)
description, 16
EVDO
description, 9
icon, 30
LED ‐ coverage is detected, 36
expanded (full) view
toggle button, 29
extension cable, 21
fastest service available, 30
FCC
compliance, 40
ID, 39
firmware updates, check for, 10
frequency bands, CDMA network, 12
47
USB 598 modem - User Guide
full view
toggle button, 29
GPS
overview, 8
GPS Monitor window, 32
icon, 31
port number, GPS, 33
GPS Monitor window, 32
hardware
memory card (microSD card), 22
modem, removing, 20
hazards, 2
help, online, 34
help, troubleshooting, 34
HEPE (Horizontal Estimated Position Error), 33
high‐speed packet data, 9
Horizontal Estimated Position Error (HEPE), 33
humidity, 37
icons
minimized, 32
system tray, 32
See also indicators.
ID, FCC, 39
ID, Industry Canada, 41
indicators
connection status, 30, 32
coverage, 30
fastest service available, 30
GPS, 31
LED lights, 35
modem status, 29
roaming, 31
signal strength, 30
SMS messages, 31
system tray, 32
Industry Canada, 36, 41
installation, 17
interference, 40
Internet, 9
latitude, 33
LBS (location based services)
See GPS.
LED lights, 35
liability, limitation of, 3
limitation of liability, 3
location based services (LBS)
See GPS.
location, current
get, 33
map of, 33
longitude, 33
map of your current location, 33
MEID (Mobile Equipment Identifier), 16
memory card (microSD card), 22
messaging, text
indicator, 31
microSD card
inserting, 22
removing, 23
minimize button, 29
minimized icons, 32
Mobile Equipment Identifier (MEID), 16
modem status, 29
no service, 36
notices, regulatory, 39
number of satellites being tracked, 33
OEM customers, 41
online Help, 34
operating hints, 34
operating systems supported, 17
operating temperature, 37
package contents, 11
packet data, high‐speed, 9
POI (points of interest), 8
points of interest (POI), 8
port, GPS, 33
pre‐activation, 15
knowledge base, 34
QNC, 10
Quick Net Connect (QNC), 10
laptop clip, 21
48
2131176
Index
radio frequency specifications, 36
regulatory information, 39
requirements, system, 17
roaming
definition, 13
indicator, 31
taskbar icons, 32
temperature, 37
text messaging
indicator, 31
tips, operating, 34
tracking session, 33
traveling speed, 33
troubleshooting, 34
TRU‐Install, 8
TRU‐Locate, 8
See also GPS.
safety, 2
sales desk, 4
satellites being tracked, number of, 33
searching for service, 35
service indicator
system tray, 32
Watcher, 30
short text messaging
indicator, 31
signal strength, CDMA network, 30
SMS
message indicator, 31
software
overview, 12
check for updates, 10
installing, 18
using, 27
specifications
electrical, 36
environmental, 37
radio frequency, 36
speed of travel, 33
status area
Windows system tray, 32
storage temperature, 37
support, 34
suspend mode, 35
system requirements, 17
system tray icons, 32
Document 2131176. Rev 1.1 Jan.10
updates, check for, 10
USB extension cable, 21
vibration, 37
Virtual Private Network (VPN), 7
Vista, 17
VPN (Virtual Private Network), 7
warning
EMI, 40
warranty, 34
Watcher software
overview, 27
check for updates, 10
installing, 18
using, 27
Windows
system tray icons, 32
versions supported, 17
Windows 7, 17
Windows Vista, 17
49
USB 598 modem - User Guide
50
2131176


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2010:01:20 14:37:02Z
Modify Date                     : 2010:01:20 14:43:33-08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Creator                         : 
Title                           : USB 598 Modem User Guide (rev 1.1)
Creator Tool                    : FrameMaker 8.0
Metadata Date                   : 2010:01:20 14:43:33-08:00
Producer                        : Acrobat Distiller 9.2.0 (Windows)
Document ID                     : uuid:474fb762-bcb4-4191-90f7-d17b9a262992
Instance ID                     : uuid:8d1e1672-8efa-43b5-aec5-b42757853027
Page Mode                       : UseOutlines
Page Count                      : 51

EXIF Metadata provided by EXIF.tools