Signify 9290012630X LED MODULE User Manual 2AGBW9290012630X Rev4

Philips Lighting(China) Investment Co.,Ltd. LED MODULE 2AGBW9290012630X Rev4

2AGBW9290012630X_User manual_Rev4

Hue Engine V1.0Specification item Value Unit ConditionDescriptionThe Hue Engine is a general purpose Zigbee certified building block for Hueconnected lighting applications e.g. Hue White, Hue White Ambiance and HueWhite and Color ambiance for lamps and luminaires. It does not work stand-alonebut is meant to be SMT soldered on a application specific motherboard thatcontains the proper interfacing for stand-alone usage.Logistical data12NC 929001263055Minimum Order Quantity 500 PCEElectrical input dataVcc voltage 3.0~3.6 Volt Ripple<50 mVCurrent (normal) 25 mAElectrical output dataAverage power consumption 85mW WattPSU wattage <60W Watt maximum wattageStandby power <150mWWiring & ConnectionsI/O definitionGround 1 GNDADC2, e.g. for voltage sensing General purpose in/out 2 2 ADC2ADC1, e.g. for current sensing 3 ADC1to be used as ADC (e.g. NTC read-out), I2C, SPI or PWM 4 Mixed_out_1to be used as ADC, I2C, SPI or PWM PWM_CHN1 5 Mixed_out_2General purpose in/out 1: E.g. for button control 6GPIO1General purpose in/out 2: E.g. for button controlPWM_CHN3 7GPIO2i.e. for current source 8EnablePWM output 9PWM_CH0PWM output 10 PWM_CH1PWM output 11 PWM_CH2PWM output 12 PWM_CH3PWM output 13 PWM_CH4Ground 14 GND3V power in 15 VDDUsed for SW programming, UART bus communication 16 TXDUsed for SW programming, UART bus communication 17 RXDUsed for SW debugging 18 NresetUsed for SW debugging 19 SWCLKUsed for SW debugging 20 SWDIOFeatures & FunctionsHue White Color Ambience yesHue White Ambiance yesHue White yesDimming yesDevice diversity yes by late state configurationAutomatic color consistency yesOTA upgrade yes Over the air upgradable when connected to the Hue BridgeWireless specificationsWireless RF mode frequency band 2400–2483.5 MHz MHzWireless communications protocol IEEE 802.15.4 ZigBee Light Link protocol Operating channel 11 – 26 channelsRange 12 meter indoorFrequency tolerances (Typical) +/-30 ppm Continuous single toneOutput power (Typical) 4 dBM Measured at antenna feedpointSpurious emissions* (Typical) -36 dBM 30 – 1000MHz-30 dBM 1 – 12.75GHz
-47 dBM 1.8 – 1.9GHz-47 dBM 5.15 – 5.3GHzEVM (Typical) 15 %rmsReceiver Sensitivity (Typical) -99 dBM PER < 1%TRP -2 dBM when mounted on a motherboard of 30x40mm (i.e. Hue Connect)LED board requirementsHue White Color Ambience Unified Gamut covered by L1.5 specificationsTunable white CCT range: 2000-6500KCRI > 80 for CCT 2000-4000KCRI > 65 for CCT 6500KR9 > 0 for CCT 2000-4000KColor consistency: 95% within 5SDCM covered by L1.5 specificationsMinimum dim-level: 2% Hue White Ambiance Tunable white CCT range: 2000-6500KCRI > 80 for CCT 2000-4000KCRI > 65 for CCT 6500KR9 > 0 for CCT 2000-4000KColor consistency: 95% within 5SDCM covered by L1.5 specificationsMinimum dim-level: 2% Hue White 2700K / 3000K / 4000KCRI > 80R9 >Color consistency: 95% within 5SDCM covered by L1.5 specificationsMinimum dim-level: 2% InsulationsDimensions & WeightLength 23.5 mm ±10% toleranceWidth 18 mm ±10% toleranceHeight 3.7 mm ±10% toleranceFixing hole diameter NA mmFixing hole distance NA mmWeight gramOperational temperatures and humidityAmbient temperature -10 to 50°C CelciusTcase-max 70°C Celcius to be measured on Hue Engine shieldMaximum housing temperatureRelative humidity Non-condensingStorage temperature and humidityAmbient temperature For 6 monthsRelative humidity Non-condensingLifetimelifetime hoursMeasured temperature at Tc-point is Tcase- max.Maximum failures = 10%Surge capabilityESD rating +/-2 KV Contact+/-4 KV AirCertificates and standardsApproval marks CE, FCC, ETSI, ROHS & REACH, ZLLCompliances and approvals
FCC FCC Labelling RequirementsWhen integrating HUE Engine V1.0 into a product it must be ensured that the FCC labelling requirements aremet. This includes a clearly visible label on the outside of the finished product specifying the FCC identifier (FCCID:2AGBW9290012630X). This exterior label can use wording such as “Contains Transmitter Module FCC ID:2AGBW9290012630X” although any similar wording that expresses the same meaning may be used.Note: Changes or modifications made to this device that are not expressly approved by Philips Lighting NorthAmerica Corporation(“Philips”) may void the user's authority to operate the device.The advance interface module complies with FCC radiation exposure limits set forth for an uncontrolledenvironment.The module and associated antenna must be installed to provide a separation distance of at least 20cm from allpersons and must not transmit simultaneously with any other antenna or transmitter.FCC ApprovalsFCC statement:This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.FCC notice:This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This device generates, uses, and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this device does causeharmful interference to radio or television reception, which can be determined by turning the device off and on,the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the separation between the device and receiver Connect the device into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/television technician for help .ICIC (Industry Canada) ApprovalsThis device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the followingtwo conditions: (1) this device may not cause interference, and (2) this device must accept any interference,including interference that may cause undesired operation of the device.Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type andmaximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interferenceto other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power(e.i.r.p.) is not more than that permitted for successful communication This module complies with FCC and Industry Canada RF radiation exposure limits set forth for generalpopulation. To maintain compliance, this module must not be co-located or operating in conjunction with anyother antenna or transmitter Immediately following the above notice, the manufacturer shall provide a list of allantenna types approved for use with the transmitter, indicating the maximum permissibleantenna gain (in dBi) and required impedance for each.The labelling requirements for Industry Canada are similar to those of the FCC. Again a clearly visibly label mustbe placed on the outside of the finished product stating something like “Contains Transmitter Module, IC-ID:20812-2630X”, although any similar wording that expresses the same meaning may be used.
Le présent appareil est conforme aux CNR d’lndustrie Canada applicables aux appareils radio exempts delicence. L’exploitation est autorisée aux deux conditions suivantes: (1) I’appareil ne doit pas produire debrouillage, et (2)I’utilisateur de I’appareil doit accepter tout brouillage radioélectrique subi, même si lebrouillage est susceptible d’en compromettre le fonctionnement.En vertu de la réglementation d’Industrie Canada, cet émetteur radio risquera uniquement à l’aide d’uneantenne de type et de gain maximum (ou moins) pour l’émetteur a approuvé par Industrie Canada. Pour réduireles interférences radio potentielles à d’autres utilisateurs, le type d’antenne et son gain doivent être choisiesque la puissance isotrope rayonnée équivalente (p.i.r.e.) n’est pas plus que celle autorisée pour unecommunication réussieCe module est conforme à la FCC et Industrie Canada RF limites d’exposition aux rayonnements définies pour l’ensemble de la population. Pour maintenir la conformité, ce module ne doit pas être co-implanté ou fonctionneren conjonction avec toute autre antenne ou émetteurÀ la suite de l’avis ci-dessus, le fabricant doit fournir une liste de tous lestypes d’antenne approuvés pour une utilisation avec l’émetteur, indiquant au maximumgain d’antenne (en dBi) et impédance requise pour chacun.Les exigences d’étiquetage pour Industrie Canada sont semblables à celles de la FCC. Encore une fois unclairement visiblement étiquette doit être placée à l’extérieur du produit fini indiquant quelque chose comme"Module émetteur de Contains, IC ID: 20812-2630 X", bien que tout même libellé qui exprime que le même senspeuvent être utilisé.IC notice:This Class B complies with Canadian ICES-005.---Cet appareil numérique de la classe B est conforme à la norme NMB 005 du CanadaCE European Certification (ETSI)The module have been certified to the following standards:• Radio: EN 300 328:V1.9.1• EMC: EN 301 489-17:V2.2.1• Safety: EN 60950-1:2006 / A12:2011If the module is incorporated into an OEM product, the OEM product manufacturer must ensure compliance of thefinal product to the European Harmonized EMC, and low voltage/safety standardsJP TELEC This exterior label can use wording such as “Contains Transmitter Module ” althoughany similar wording that expresses the same meaning may be used.CN SRRC This exterior label can use wording such as “Contains Transmitter Module ”although any similar wording that expresses the same meaning may be used.Inrush currentEarth leakage currentHue Connect 24V DC in/out 60W HWCA V1.0Specification item Value Unit Condition
DescriptionThe Hue Connect is a motherboard that accommodates the Hue Engine. Itsapplication is intended to be used for color tunable luminaires. In combinationwith the a 24V DC power supply and defined L1.5 LED kit, color consistencycan between luminaires or light points within a luminaire can be guaranteed.Logistical data12NC 929001263155Minimum Order Quantity 1024 PCEFeatures & FunctionsElectrical input dataInput power 60WCurrent of single channel 2.5A AmpereElectrical output data WattVoltage 24V Volt +/-1VAverage power consumptionStandby powerWiring & ConnectionsJ1 connector Output to Sensor or 2nd light sourceGND 1 GND3V3 supply to auxilary microcontroller of sensor / 2nd light source 2 VDDInput pin for simple sensor or reset pin for auxiliary micro 3GPIO1I2C 4SDAI2C 5SCLInput pin for simple sensor or reset pin for auxiliary micro 6GPIOJ2 connector connector to L2 LED boardVBUS 1Pin connects to Red (Hue), 2200K (Tone), 2700K (Lux) or 4000K (Lux2Pin connects Green (Hue or Tone) or Lime (Tone) to GND via MOSFE3Pin connects Blue (Hue) or 6500K (Tone) to GND via MOSFET 4Pin connects 2200K (Hue) to GND via MOSFET 5Pin connects 6500K (Hue) to GND via MOSFET 6J3 connector Power in24V 1GND 2J4 connector Pragram connector (internal use)Operational temperatures and humidityAmbient temperature -10 to 50°C CelciusTcase-maxMaximum housing temperatureRelative humidityStorage temperature and humidityAmbient temperatureRelative humidityLifetimelifetimeSurge capabilityESD rating +/-2 KV Contact+/-4 KV AirCertificates and standardsApproval marksCompliances and approvals
Inrush currentEarth leakage current

Navigation menu