Signify 9290012630X LED MODULE User Manual 2AGBW9290012630X Rev4
Philips Lighting(China) Investment Co.,Ltd. LED MODULE 2AGBW9290012630X Rev4
Signify >
2AGBW9290012630X_User manual_Rev4
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3003195 |
| Application ID | rcVoUSBeeyGXwmcPgcA/bw== |
| Document Description | 2AGBW9290012630X_User manual_Rev4 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 6.58kB (82263 bits) |
| Date Submitted | 2016-05-25 00:00:00 |
| Date Available | 2016-05-25 00:00:00 |
| Creation Date | 2016-05-25 14:34:58 |
| Producing Software | Acrobat Distiller 10.1.16 (Windows) |
| Document Lastmod | 2016-05-25 14:34:58 |
| Document Title | data sheet Hue Engine Hue Connect_draft v0 1_MY.xlsx |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | Alan |
Hue Engine V1.0 Specification item Value Unit The Hue Engine is a general purpose Zigbee certified building block for Hue connected lighting applications e.g. Hue White, Hue White Ambiance and Hue White and Color ambiance for lamps and luminaires. It does not work stand-alone but is meant to be SMT soldered on a application specific motherboard that contains the proper interfacing for stand-alone usage. Description Logistical data 12NC Minimum Order Quantity Condition 929001263055 500 PCE 3.0~3.6 25 Volt mA 85mW <60W <150mW Watt Watt 10 11 12 13 14 15 16 17 18 19 20 GND ADC2 ADC1 Mixed_out_1 Mixed_out_2 GPIO1 GPIO2 Enable PWM_CH0 PWM_CH1 PWM_CH2 PWM_CH3 PWM_CH4 GND VDD TXD RXD Nreset SWCLK SWDIO Electrical input data Vcc voltage Current (normal) Ripple<50 mV Electrical output data Average power consumption PSU wattage Standby power Wiring & Connections Ground ADC2, e.g. for voltage sensing General purpose in/out 2 ADC1, e.g. for current sensing to be used as ADC (e.g. NTC read-out), I2C, SPI or PWM to be used as ADC, I2C, SPI or PWM PWM_CHN1 General purpose in/out 1: E.g. for button control General purpose in/out 2: E.g. for button controlPWM_CHN3 i.e. for current source PWM output PWM output PWM output PWM output PWM output Ground 3V power in Used for SW programming, UART bus communication Used for SW programming, UART bus communication Used for SW debugging Used for SW debugging Used for SW debugging maximum wattage I/O definition Features & Functions Hue White Color Ambience Hue White Ambiance Hue White Dimming Device diversity Automatic color consistency OTA upgrade yes yes yes yes yes yes yes by late state configuration Over the air upgradable when connected to the Hue Bridge Wireless specifications Wireless RF mode frequency band Wireless communications protocol Operating channel Range Frequency tolerances (Typical) Output power (Typical) Spurious emissions* (Typical) 2400–2483.5 MHz IEEE 802.15.4 11 – 26 12 +/-30 -36 -30 MHz ZigBee Light Link protocol channels meter ppm dBM dBM dBM indoor Continuous single tone Measured at antenna feedpoint 30 – 1000MHz 1 – 12.75GHz EVM (Typical) Receiver Sensitivity (Typical) TRP -47 -47 15 -99 -2 dBM dBM %rms dBM dBM 1.8 – 1.9GHz 5.15 – 5.3GHz PER < 1% when mounted on a motherboard of 30x40mm (i.e. Hue Connect) LED board requirements Hue White Color Ambience Hue White Ambiance Hue White Unified Gamut Tunable white CCT range: 2000-6500K CRI > 80 for CCT 2000-4000K CRI > 65 for CCT 6500K R9 > 0 for CCT 2000-4000K Color consistency: 95% within 5SDCM Minimum dim-level: 2% Tunable white CCT range: 2000-6500K CRI > 80 for CCT 2000-4000K CRI > 65 for CCT 6500K R9 > 0 for CCT 2000-4000K Color consistency: 95% within 5SDCM Minimum dim-level: 2% 2700K / 3000K / 4000K CRI > 80 R9 > Color consistency: 95% within 5SDCM Minimum dim-level: 2% covered by L1.5 specifications covered by L1.5 specifications covered by L1.5 specifications covered by L1.5 specifications Insulations Dimensions & Weight Length Width Height Fixing hole diameter Fixing hole distance Weight 23.5 18 3.7 NA NA mm mm mm mm mm gram -10 to 50°C 70°C Celcius Celcius ±10% tolerance ±10% tolerance ±10% tolerance Operational temperatures and humidity Ambient temperature Tcase-max Maximum housing temperature Relative humidity to be measured on Hue Engine shield Non-condensing Storage temperature and humidity Ambient temperature Relative humidity For 6 months Non-condensing Lifetime lifetime hours Measured temperature at Tc-point is Tcase- max. Maximum failures = 10% KV KV Contact Air Surge capability ESD rating +/-2 +/-4 Certificates and standards Approval marks Compliances and approvals CE, FCC, ETSI, ROHS & REACH, ZLL FCC FCC Labelling Requirements When integrating HUE Engine V1.0 into a product it must be ensured that the FCC labelling requirements are met. This includes a clearly visible label on the outside of the finished product specifying the FCC identifier (FCC ID:2AGBW9290012630X). This exterior label can use wording such as “Contains Transmitter Module FCC ID: 2AGBW9290012630X” although any similar wording that expresses the same meaning may be used. Note: Changes or modifications made to this device that are not expressly approved by Philips Lighting North America Corporation(“Philips”) may void the user's authority to operate the device. The advance interface module complies with FCC radiation exposure limits set forth for an uncontrolled environment. The module and associated antenna must be installed to provide a separation distance of at least 20cm from all persons and must not transmit simultaneously with any other antenna or transmitter. FCC Approvals FCC statement: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC notice: This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the separation between the device and receiver Connect the device into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/television technician for help . IC (Industry Canada) Approvals This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication This module complies with FCC and Industry Canada RF radiation exposure limits set forth for general population. To maintain compliance, this module must not be co-located or operating in conjunction with any other antenna or transmitter Immediately following the above notice, the manufacturer shall provide a list of all antenna types approved for use with the transmitter, indicating the maximum permissible antenna gain (in dBi) and required impedance for each. The labelling requirements for Industry Canada are similar to those of the FCC. Again a clearly visibly label must be placed on the outside of the finished product stating something like “Contains Transmitter Module, IC-ID: 20812-2630X”, although any similar wording that expresses the same meaning may be used. IC Le présent appareil est conforme aux CNR d’lndustrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) I’appareil ne doit pas produire de brouillage, et (2)I’utilisateur de I’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. En vertu de la réglementation d’Industrie Canada, cet émetteur radio risquera uniquement à l’aide d’une antenne de type et de gain maximum (ou moins) pour l’émetteur a approuvé par Industrie Canada. Pour réduire les interférences radio potentielles à d’autres utilisateurs, le type d’antenne et son gain doivent être choisies que la puissance isotrope rayonnée équivalente (p.i.r.e.) n’est pas plus que celle autorisée pour une communication réussie Ce module est conforme à la FCC et Industrie Canada RF limites d’exposition aux rayonnements définies pour l ’ensemble de la population. Pour maintenir la conformité, ce module ne doit pas être co-implanté ou fonctionner en conjonction avec toute autre antenne ou émetteur À la suite de l’avis ci-dessus, le fabricant doit fournir une liste de tous les types d’antenne approuvés pour une utilisation avec l’émetteur, indiquant au maximum gain d’antenne (en dBi) et impédance requise pour chacun. Les exigences d’étiquetage pour Industrie Canada sont semblables à celles de la FCC. Encore une fois un clairement visiblement étiquette doit être placée à l’extérieur du produit fini indiquant quelque chose comme "Module émetteur de Contains, IC ID: 20812-2630 X", bien que tout même libellé qui exprime que le même sens peuvent être utilisé. CE IC notice: This Class B complies with Canadian ICES-005.--Cet appareil numérique de la classe B est conforme à la norme NMB 005 du Canada European Certification (ETSI) The module have been certified to the following standards: • Radio: EN 300 328:V1.9.1 • EMC: EN 301 489-17:V2.2.1 • Safety: EN 60950-1:2006 / A12:2011 If the module is incorporated into an OEM product, the OEM product manufacturer must ensure compliance of the final product to the European Harmonized EMC, and low voltage/safety standards JP TELEC This exterior label can use wording such as “Contains Transmitter Module any similar wording that expresses the same meaning may be used. This exterior label can use wording such as “Contains Transmitter Module although any similar wording that expresses the same meaning may be used. ” although ” CN SRRC Inrush current Earth leakage current Hue Connect 24V DC in/out 60W HWCA V1.0 Specification item Value Unit Condition The Hue Connect is a motherboard that accommodates the Hue Engine. Its application is intended to be used for color tunable luminaires. In combination with the a 24V DC power supply and defined L1.5 LED kit, color consistency can between luminaires or light points within a luminaire can be guaranteed. Description Logistical data 12NC Minimum Order Quantity 929001263155 1024 PCE Features & Functions Electrical input data Input power Current of single channel Electrical output data Voltage Average power consumption Standby power 60W 2.5A 24V Ampere Watt Volt +/-1V Wiring & Connections J1 connector GND 3V3 supply to auxilary microcontroller of sensor / 2nd light source Input pin for simple sensor or reset pin for auxiliary micro I2C I2C Input pin for simple sensor or reset pin for auxiliary micro J2 connector VBUS Pin connects to Red (Hue), 2200K (Tone), 2700K (Lux) or 4000K (Lux Pin connects Green (Hue or Tone) or Lime (Tone) to GND via MOSFE Pin connects Blue (Hue) or 6500K (Tone) to GND via MOSFET Pin connects 2200K (Hue) to GND via MOSFET Pin connects 6500K (Hue) to GND via MOSFET J3 connector 24V GND J4 connector Output to Sensor or 2nd light source 1 GND 2 VDD 3 GPIO1 4 SDA 5 SCL 6 GPIO connector to L2 LED board Power in Pragram connector (internal use) Operational temperatures and humidity Ambient temperature Tcase-max Maximum housing temperature Relative humidity -10 to 50°C Celcius +/-2 +/-4 KV KV Storage temperature and humidity Ambient temperature Relative humidity Lifetime lifetime Surge capability ESD rating Certificates and standards Approval marks Compliances and approvals Contact Air Inrush current Earth leakage current
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Alan Create Date : 2016:05:25 14:34:58+08:00 Modify Date : 2016:05:25 14:34:58+08:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Producer : Acrobat Distiller 10.1.16 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Format : application/pdf Title : data sheet Hue Engine Hue Connect_draft v0 1_MY.xlsx Creator : Alan Document ID : uuid:c498cd02-02ca-4cd2-9016-eb707739f3b5 Instance ID : uuid:3ec63759-5245-4317-a0a3-6b044d825fc6 Page Count : 6EXIF Metadata provided by EXIF.tools