Silex Technology SXDS3000WAN SX-DS-3000WAN User Manual Manual
Silex Technology, Inc. SX-DS-3000WAN Manual
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1612586 |
| Application ID | qZk7JE6kyIcO7EVP5mokeQ== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 237.18kB (2964702 bits) |
| Date Submitted | 2011-12-30 00:00:00 |
| Date Available | 2011-12-30 00:00:00 |
| Creation Date | 2011-12-21 15:18:09 |
| Producing Software | Adobe Acrobat Pro 9.2.0 |
| Document Lastmod | 2011-12-21 15:18:31 |
| Document Title | Manual |
| Document Creator | Adobe Acrobat Pro 9.2.0 |
English Easy Setup Using WPS Feature WA100070XX SX-DS-3000WAN allows you to configure its wireless settings easily using a push switch if your wireless router supports WPS (Wi-Fi Protected Setup). This sheet explains how to configure wireless settings using the push switch. ! NOTE To perform the wireless configuration using WPS, your wireless router must support WPS. Please make sure that a wireless router supporting WPS is set up in your environment. While performing this configuration, please temporarily move SX-DS-3000WAN closer to your wireless router to make it easier for both devices to communicate. Depending on your wireless router, WPS may need to be enabled manually. For details, refer to the operation manual that came with your wireless router. If a security feature such as MAC Address filtering is enabled on your wireless router, disable it temporarily so that SX-DS-3000WAN can communicate with your wireless router. Connect the AC adaptor to SX-DS-3000WAN and the AC plug to the power outlet. Confirm that the Wireless LED(WLAN) on SX-DS-3000WAN blinks in Orange or turns to Green. Press the WPS button on your wireless router. Confirm that your wireless router is ready for a wireless connection to be made. Power Outlet SX-DS-3000WAN or SX-DS-3000WAN Searching for network AC Adaptor - If the Wireless LED does not blink in Orange or turn to Green, reset SX-DS-3000WAN to factory defaults and start from step 1 again. For how to reset SX-DS-3000WAN to its factory defaults, refer to the Users Manual or Setup Guide. - It is not necessary to connect a network cable to SX-DS-3000WAN. Press and hold the push switch on SX-DS-3000WAN. When the Wireless LED blinks in Green, release the push switch. Connected to existing network SX-DS-3000WAN will start to communicate with your wireless router. The Wireless LED's lighting pattern will show you if the wireless configuration succeeded or failed. SX-DS-3000WAN or Push Switch SX-DS-3000WAN Success WPS Wireless Router - The name, position and shape of the WPS button will differ depending on your wireless router. For details, refer to the operation manual that came with your wireless router. - Please use only one wireless router. If two or more routers are waiting for wireless connections, SX-DS-3000WAN will not be able to connect properly. When successful, the Wireless LED will turn to Green. In this case, wireless configuration is complete. - Power off SX-DS-3000WAN, move it to where you wish to use it and then power it on again. - Connect the USB device(s) that you wish to use over the network to SX-DS-3000WAN. - To install the software applications onto your computer, click Computer Configuration from the menu screen. For details, refer to the Users Manual. Fail - It is not necessary to install the applications if you plan to use printers with the standard Windows printing feature. When wireless configuration has failed, the Wireless LED will blink in Red. - Within 3-10 sec after pressing and holding down the push switch, the Wireless LED will blink in Green. - It may take a while to complete the wireless configuration depending on your environment (up to 2 min). Read the instructions on this sheet and start from step 3 again. August, 2011 SX-DS-3000WAN User Registration Step1 Necessary Wireless Setting Information Please complete the user registration after you finish the setup. It is required to provide you better technical supports and services. To use SX-DS-3000WAN in your wireless network, SX-DS-3000WAN must have the same settings as your wireless router (Access Point). Please check the wireless settings of your router and write it down on the table below: User Registration Website * The information below will be your own information that is used on your network and none of us are able to find it from our side. For how to see each setting, please refer to the operating manual that came with your router or contact the manufacturer. http://www.silex.jp/register/ For the user registration, a Serial Number is required. The Serial Number is a last 6-digit number of the Ethernet Address(12-digit number) which can be found on the bottom of the unit. Configuration Memo Wireless Mode There are "Infrastructure" mode and "Ad hoc" mode. Select "Infrastructure" mode when you wish to connect to your network via a wireless router. Select "Ad hoc" mode when you wish to make a direct connection to your wireless computer without using a wireless router. When using this mode, set the same channel as your wireless computer. SSID The SSID is an ID that distinguishes a wireless LAN network from others. For wireless devices to communicate with each other on a wireless network, they must share the same SSID. (The SSID is also referred to as "ESSID".) Depending on your wireless router, it may have several SSIDs. If there are different SSIDs for a game machine and computer, use the one for the computer. Example: If the Ethernet Address is "00:80:92:00:11:22", the Serial Number will be "001122". English WA06170XX Thank you very much for purchasing our wireless USB Device Server "SX-DS-3000WAN". This Setup Guide provides information on how to configure and use SX-DS-3000WAN in your network environment. Please follow instructions on Step1- Step 4 to configure SX-DS-3000WAN. Before you begin, please carefully read the "Safety Instructions" and "About Wireless Interference" in the online manual included in the CD-ROM to properly configure SX-DS-3000WAN. (De) Auf der CD-ROM befindet sich ein deutschsprachiges Setup-Handbuch im PDF-Format. Zum Anzeigen der PDF-Datei unter Windows benötigen Sie den Acrobat Reader. (Fr) Un guide d'installation en français au format PDF est inclus dans le CD-ROM. Acrobat Reader est nécessaire pour lire les fichiers PDF dans un environnement Windows. Una Guida alla configurazione in italiano è inclusa nel CD-ROM come file PDF. Per visualizzare il file PDF in ambiente Windows è necessario Acrobat Reader. (It) (Es) En el CD-ROM se incluye una Guía de instalación en español como archivo PDF. Se necesita Acrobat Reader para ver el archivo PDF en un entorno Windows. (Pt) Um Guia de Configuração em português é fornecido no CD-ROM no formato de arquivo PDF. É necessário ter o Acrobat Reader para visualizar o arquivo PDF em um ambiente Windows. Please check the following items are bundled with SX-DS-3000WAN: (Including configuration software and online manual) About configuration methods Setup Guide (this document) SX Virtual Link User’s Guide Warranty Booklet Rubber feet (4 psc) This Setup Guide explains how to configure SX-DS-3000WAN using a network cable. For other configuration methods, please refer to the online manual included in the CD-ROM. - Configuration using a network cable (Recommended) By connecting SX-DS-3000WAN to your existing network using a network cable, you can configure the network settings from your computer. For this method, a network cable is required. Sample connection No Encryption Network Cable Wireless Router Encryption Mode (Network Authentication) SX-DS-3000WAN - Configuration using a WPS feature of your wireless router If your wireless router supports WPS (Wi-Fi Protected Setup), the network configuration can be done automatically by pressing the wireless connection button on your wireless router and the push switch on SX-DS-3000WAN. For this configuration method, a wireless router supporting WPS is required. Network Authentication WEP WPA / WPA2 Uses PSK for network authentication. The encryption key will be generated by communicating with the wireless router using a Pre-Shared key. WEP key setting is not used for this mode. Set the same "Pre-Shared key" and "Encryption Mode"(TKIP/AES) as your wireless router. The Pre-Shared key is also referred to as "Network Key" or "Password". By saving the configuration information to a USB flash drive and connecting it to SX-DS-3000WAN, you can configure the network settings. To save the configuration information to the USB flash drive, please use the configuration utility contained in the CD-ROM. For this configuration method, a USB flash drive is required. Connect SX-DS-3000WAN to your wireless router using a network cable. Wireless Router Connect the AC adaptor to SX-DS-3000WAN and the AC plug to the power outlet. SX-DS-3000WAN WPA2 Power Outlet POWER LED The AC adaptor is not plugged properly. Start from Step2-2 again. LAN LED If LAN LED turns to Green or Orange Succsessfully connected to your network. Go on to Step 3. SX-DS-3000WAN (4) (6) (8) Network Cable (10) If POWER LED is OFF Confirm that both POWER LED and LAN LED turn on. If LAN LED is OFF The network cable is not plugged properly. Start from Step2-1 again. If the network cable is plugged properly, SX-DS-3000WAN may contain ON (9) WPA WEP key Size and Key Index or Encryption Mode SX-DS-3000WAN E/ A : 008092XXXXXX S/ N : YYYYYYYYY WEP (Open / Shared) WEP Key or Pre-Shared Key and (5) (7) Connect SX-DS-3000WAN to your network using a network cable. Parts and Fucntions (1) (2)(3) Ad hoc (ch. SSID Uses no encryption for wireless communication. (In this case, you do not have to check any of your settings beforehand.) If WEP encryption is used, wireless communication will be encrypted using the settings for "WEP Key 1-4" and "Key Index". Set the same "WEP key Size(64bit/128bit)", "WEP Key" and "Key Index" as your wireless router. - Configuration using a USB flash drive Following 3 configuration methods are supported. Step2 Getting Started Package Contents SX-DS-3000WAN AC Adaptor Device Server Setup CD Before You Begin Infrastructure ON AC Adaptor icorrect network settings. In such a case, reset SX-DS-3000WAN to factory defaults and start from Step2-1 again. For details on how to reset SX-DS-3000WAN to factory defaults, refer to “Factory Default Configuration”. Factory Default Configuration (1) Power Connector (6) STATUS LED (2) Network Port (7) POWER LED (3) Push Switch (8) USB Port (4) Wireless LED (9) Ethernet Address (5) LAN LED (10) Serial Number If SX-DS-3000WAN has been used in other network or you wish to start configuration from factory defaults again, follow the instructions below. Remove the AC plug from the power outlet. Power Outlet Press and hold down the push switch on SX-DS-3000WAN while inserting the AC plug back into the power outlet. Keep holding a while and release the push switch when LAN LED turns to Red. Push Switch SX-DS-3000WAN Power Outlet Keep holding down the push switch Push Switch SX-DS-3000WAN LAN LED ON Configure SX-DS-3000WAN using the configuration software included in the Device Server Setup CD. The configuration can be done from Windows or Macintosh computers. Step3 Setup SX-DS-3000WAN <<< Windows environment >>> Click Device Server Configuration. Click Yes. Check the notice information and click Next. Read the software license agreement and click Yes. Insert the Device Server Setup CD into your computer. * If the menu screen does not appear automatically, open My Computer, select the CD-ROM drive and execute Autorun.exe. Click Configure using the setup utility (Recommended). Select SX-DS-3000WAN and click Next. * If SX-DS-3000WAN is not displayed in a list,,, - Check the network setting on your computer (IP address setting) is properly configured. - Please temporarily disable the security software (e.g. "Virus Buster" of Trend Micro, Inc.) or the firewall function of Windows XP. <<< Macintosh environment >>> Insert the Device Server Setup CD into your computer. Select SX-DS-3000WAN and click Next. Restart SX-DS-3000WAN to take effect of the new settings. Select the wireless network that you wish to connect to from a list , enter the network key and click Next. * If you wish to assign the IP address manually, click Assign IP Address and enter the IP address, subnet mask and default gateway. * If the window does not have the option, ”Get IP Address Automatically”, it is unable to obtain the IP address from DHCP server. In such a case, the sample address created with your computer's setting will be displayed. Please enter the IP address manually. Double click the CD-ROM icon ( and then double click DSSetup ( Select Get IP Address Automatically and click Next. ). Remove the AC plug from the power outlet and then network cable from SX-DS-3000WAN. Power Outlet SX-DS-3000WAN Click Device Server Configuration. Select the wireless network that you wish to connect to from a list, enter the network key and click Next. Click Configure using the setup utility (Recommended). Connect the USB device that you wish to use over the network to SX-DS-3000WAN using a USB cable and then insert the AC plug of SX-DS-3000WAN to the power outlet. Confirm that the Wireless LED turns on. Wireless LED Power Outlet Check the notice information and click Next. 10 Check the settings and click Execute. USB Devices * The information diplayed here will differ depending on how you have configured. If Wireless LED turns to Green Successfully connected to the wireless network. The setup is complete now. If Wireless LED blinks in Orange SX-DS-3000WAN Network Cable Check the settings and click Execute. * The information diplayed here will differ depending on how you have configured. * Use the wireless setting information that you have checked at Step 1. Select the SSID of the wireless network that you with to connect to and enter the network key. If the wireless network that you wish to connect to is not shown on a list, click Detailed Config button and configure each setting in the window displayed. * If you plan to use SX-DS-3000WAN on a wired network using a network cable, check Skip wireless configuration and click Next. SX-DS-3000WAN * If you plan to use SX-DS-3000WAN on a wired network, it is not necessary to unplug the network cable. 10 * Use the wireless setting information that you have checked at Step 1. Select the SSID of the wireless network that you to connect to and enter the network key. If the wireless network that you wish to connect to is not shown on a list, click Detailed Config button and configure each setting in the window displayed. * If you plan to use SX-DS-3000WAN on a wired network using a network cable, check Skip wireless configuration and click Next. * If you wish to assign the IP address manually, click Assign IP Address and enter the IP address, subnet mask and default gateway. * If the window does not have the option, ”Get IP Address Automatically“, it is unable to obtain the IP address from DHCP server. In such a case, the sample address created with your computer's setting will be displayed. Please enter the IP address manually. * If SX-DS-3000WAN is not displayed in a list,,, - Check the network setting on your computer (IP address setting) is properly configured. Step4 Enabling the New Settings Select Get IP Address Automatically and click Next. * In Windows 7 (or Windows Vista), the User Account Control screen is displayed. Click Yes. (Click Continue in Windows Vista). ON Searching for a wireless network. Please wait until a wireless connection is made. When not connected within 2-3 min, the SX-DS-3000WAN's wiress settings may not have been configured properly. Go back to Step 1 and check the wireless setting information once again. 11 Click Yes and click Finish. Before clicking Finish, follow the instructions on Step 4 to take effect of the configuration you made. After completing Step 4, click Finish and go on to install the USB device connection utility, "SX Virtual Link". 11 Read the software license agreement and click Yes. Click Yes and click Finish. Before clicking Finish, follow the instructions on Step 4 to take effect of the configuration you made. After completing Step 4, click Finish and go on to install the USB device connection utility, "SX Virtual Link". If Wireless LED is OFF The network cable is plugged. When you plan to use SX-DS-3000WAN in a wireless network, follow the instructions from Step 4-1 again. When you plan to use SX-DS-3000WAN in a wired network, check the LAN LED's lighting pattern. If the LAN LED turns to Green or Orange, SX-DS-3000WAN has been connected to a wired network. The setup is complete now. Go on to install the USB device connection utility, SX Virtual Link. Please refer to the "SX Virtual Link User's Guide". Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. a particular installation. However, there is no guarantee that interference will not occur in If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device is restricted to indoor use when operated in the 5.15 to 5.25 GHz frequency range. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Canada Request This device complies with Industry Canada licence‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The device for the band 5150‐5250 MHz is only for indoor usage to reduce potential for harmful interference to co‐channel mobile satellite systems; This Class B digital apparatus complies with Canadian ICES‐003. Cet appareil numerique de la classe B est conforme a la norme NMB‐003 du Canada. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Create Date : 2011:12:21 15:18:09+08:00 Creator : Adobe Acrobat Pro 9.2.0 Modify Date : 2011:12:21 15:18:31+08:00 Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2011:12:21 15:18:31+08:00 Creator Tool : Adobe Acrobat Pro 9.2.0 Format : application/pdf Document ID : uuid:b4cdd73a-1a21-4e8a-9772-14ebefc20494 Instance ID : uuid:47026e7b-0d55-4131-bb8d-2f4182ecb9bb Producer : Adobe Acrobat Pro 9.2.0 Page Count : 4 For : saimyouji, Title : WA06170XX_01.ai Bounding Box : -1094 -598 1488 317 Container Version : 11 Creator Version : 15EXIF Metadata provided by EXIF.tools