Simrad RS87 RS87 VHF Marine Radiotelephone with Class D DSC User Manual RS87 Manual

Simrad Ltd RS87 VHF Marine Radiotelephone with Class D DSC RS87 Manual

User manual

ALWAYS AT THE FOREFRONT OF TECHNOLOGY
Instruction ManualIIISimrad RS87VHF Radio SystemMANUAL
RS87 VHFIV Part No. E04297 Issue 1.1 05/03/03 MDLThe technical data, information and illustrations contained in this publication were to the best of our knowledge correct at the time ofgoing to print. We reserve the right to change specifications, equipment, installation and maintenance instructions without notice aspart of our policy of continuous development and improvement.No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form, electronic or otherwise withoutprior permission from Simrad Ltd.No liability can be accepted for any inaccuracies or omissions in the publication, although every care has been taken to make it as com-plete and accurate as possible.©2003 Simrad Ltd
CONTENTS1. GENERAL 1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81.2 The Simrad integrated system . . . . . . . . . . . . . . . . . . . . . . . 91.3 Licensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101.4 Entering MMSI numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111.5 Group ID MMSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112. MAIN FUNCTIONS2.1 General notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122.2 Switching on & Second Country mode . . . . . . . . . . . . . . . . 122.3 Changing channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132.3.1 Channel Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142.4 Volume adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152.5 Squelch adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152.6 Dual Watch mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152.7 Tri-Watch mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162.8 All Scan mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172.8.1 Dynamic All Scan Inhibit . . . . . . . . . . . . . . . . . . . . . . 172.9 Memory Scan mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182.9.1 Dynamic Memory Scan Delete . . . . . . . . . . . . . . . . . . 182.10 Adjusting backlighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192.11 Handset off cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193. MENU MODE3.1 Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203.1.1 All Scan inhibit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213.1.2 All Scan reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213.1.3 All Scan show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223.1.4 Memory Scan select . . . . . . . . . . . . . . . . . . . . . . . . . . . 223.1.5 Memory Scan clear . . . . . . . . . . . . . . . . . . . . . . . . . . . 233.1.6 Memory Scan show . . . . . . . . . . . . . . . . . . . . . . . . . . . 233.1.7 Scan dwell time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233.2 Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243.2.1 Ship’s MMSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243.2.2 ATIS number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253.2.3 Group MMSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263.3 VHF items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273.3.1 User channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273.3.2 Position view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283.3.3 Last used channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283.3.4 Interrupt intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293.3.5 Auxiliary audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293.3.6 Speaker settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Instruction ManualV
CONTENTS ctd -4. DSC FUNCTIONS4.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314.2 Making a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314.2.1 Individual Routine call . . . . . . . . . . . . . . . . . . . . . . . . 314.2.2 Public Correspondence call . . . . . . . . . . . . . . . . . . . . . 324.2.3 All Ships Safety call . . . . . . . . . . . . . . . . . . . . . . . . . . . 344.2.4 All Ships Urgency call . . . . . . . . . . . . . . . . . . . . . . . . . 344.2.5 Group call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354.2.6 Distress Alert call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354.3 Receiving a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374.3.1 Individual Routine call . . . . . . . . . . . . . . . . . . . . . . . . 374.3.2 Public Correspondence call . . . . . . . . . . . . . . . . . . . . . 384.3.3 All Ships Safety call . . . . . . . . . . . . . . . . . . . . . . . . . . . 394.3.4 All Ships Urgency call . . . . . . . . . . . . . . . . . . . . . . . . . 394.3.5 Group call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404.3.6 Distress Alert call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414.3.7 Distress Alert acknowledgement . . . . . . . . . . . . . . . . 424.3.8 Distress Relay call . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434.4 Viewing the Call Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444.5 Position over 4 hours old . . . . . . . . . . . . . . . . . . . . . . . . . . . 455. THE DIRECTORY5.1 Switching between the directories . . . . . . . . . . . . . . . . . . . . 465.2 Viewing the directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465.3 Entering a number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475.4 Editing a number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486. MISCELLANEOUS FUNCTIONS6.1 Selecting Weather Watch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 496.1.1 Weather Watch alert . . . . . . . . . . . . . . . . . . . . . . . . . . . 496.2 Security mode (voice scrambler) . . . . . . . . . . . . . . . . . . . . . 506.3 Editing Latitude, Longitude and UTC . . . . . . . . . . . . . . . . . 506.4 Toggling between Lat/Long and UTC views . . . . . . . . . . . 516.5 Intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 526.5.1 Making an intercom call . . . . . . . . . . . . . . . . . . . . . . . 526.5.2 Receiving an intercom call . . . . . . . . . . . . . . . . . . . . . 536.6 Loudhailer / Foghorn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546.6.1 Loudhailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546.6.2 Foghorn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556.7 station speaker mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 566.8 iDSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56RS87 VHF6Part No. E04297
CONTENTS ctd -7. INSTALLATION7.1 Physical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 577.1.2 Transceiver installation . . . . . . . . . . . . . . . . . . . . . . . . 577.1.2 Handset installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 587.1.3 Station speaker installation . . . . . . . . . . . . . . . . . . . . . 597.2 Electronic installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 597.2.1 Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 607.2.2 Loudspeakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 617.2.3 Intercoms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 617.2.4 Loudhailer/Foghorns . . . . . . . . . . . . . . . . . . . . . . . . . 627.2.5 Remote foghorn button . . . . . . . . . . . . . . . . . . . . . . . . 627.2.6 Auxiliary audio input . . . . . . . . . . . . . . . . . . . . . . . . . 637.2.7 NMEA0183 input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 637.2.8 iDSC output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 647.2.9 Future options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 647.2.10 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 657.2.11 Cable strain relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . 667.3 Antenna installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 667.4 Electrical interference suppression . . . . . . . . . . . . . . . . . . . . 688. APPENDIX 8.1 Operating procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 698.1.1 Sending a distress alert . . . . . . . . . . . . . . . . . . . . . . . . 698.1.2 Acknowledging and relaying a distress alert . . . . . . 698.1.3 Cancelling a distress alert . . . . . . . . . . . . . . . . . . . . . . 708.1.4 Alerting all vessels within range . . . . . . . . . . . . . . . . 708.1.5 Calling a coast station . . . . . . . . . . . . . . . . . . . . . . . . . 708.1.6 Making an intership call . . . . . . . . . . . . . . . . . . . . . . . 708.2 NMEA sentences received . . . . . . . . . . . . . . . . . . . . . . . . . . 708.3 Transmission range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 718.4 Frequency of channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 728.5 Fault finding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 738.6 Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 748.7 Technical specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 758.8 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 758.9 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . 768.10 Service & warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Instruction Manual7Part No. E04297
1 GENERAL1.1 IntroductionThe RS87 is a modular VHF radio and Class D DigitalSelective Calling (DSC) radio telephone system using a fullyfeatured telephone-style handset to access and control all func-tions. It supports the latest GMDSS requirements for non-SOLAS vessels from the International Maritime Organisation(IMO). It will enable you to make digitally selected calls,which are quicker and simpler to make than traditional voicecalls using Channel 16. Should a distress situation occur, withthe RS87 you can quickly raise an alert, indicating your identi-ty, your position and automatically establish distress communi-cation on the emergency voice channel.The RS87 transceiver is robustly constructed using a pressuredie cast aluminium case for effective heat dissipation, ensuringmaximum transmission performance even after many hoursconstant use.Thank you for choosing SimradIf you are pleased with your VHF we hope you will be interest-ed in our range of marine electronic equipment, which is man-ufactured to the same high standards as the RS87. Please con-tact your nearest Simrad Agent for a catalogue showing ourincreasing range of high tech navigational instruments, GPS,autopilots, Radar, Echosounders, Chartplotters and VHF radiosets.Simrad operate a policy of continual development and reservethe right to alter and improve the specification of their prod-ucts without notice.RS87 VHF8Part No. E04297WX WATCHSPEAKERDIRTEL CALLVOLVOL ON/CLAT/LONCH SETLIFTCOVER DISTRESS16VOLUME 1 1SQUELCH 07INTFig 1.1 - RS87 Handset
1.2 The Simrad integrated systemThe standard RS87 radiotelephone can support up to two sta-tions with full intercom facility, geographical position inputvia NMEA0183 and iDSC integration with Simrad chartplotterswhich enables the plotters to display DSC call information.With the addition of the expansion board, the system can sup-port an additional two stations, two intercom speakers and for-ward and aft foghorn/loudhailer speakers in addition to thestandard functions.Additional stations can either be another RS87 type telephonehandset, or an RS86 fixed panel display, with a passive tele-phone handset or fistmike allowing great flexibility in installa-tions (Fig 1.2) -Instruction Manual9Part No. E04297Fig 1.2 - RS87 system optionsDUAL STATION SYSTEMEXPANDED SYSTEMBASIC SYSTEM
1.3 LicensingNOTE Prior to use check the national licensing requirements for the operator.In the UK license applications and queries should be made tothe following authority -Ship Radio LicensingRadio Licensing CentreThe Post OfficePO Box 1495BristolBS99 3QSAset may only be operated by, or under the supervision of aholder of a Certificate of Competence and Authority toOperate. This involves a simple examination and an annuallicense renewal fee. The VHF only certificate is administeredby the Royal Yachting Association -Royal Yachting AssociationRYA HouseRomsey RoadEastleighHants, SO5 4YAHolders of the Restricted Certificate of Competence in Radio-telephony (which covers MF/HF SSB etc), do not need a sepa-rate VHF certificate.In all other countries, please contact your regional authority forinformation.RS87 VHF10 Part No. E04297
1.4 Entering MMSI numbersAt the time of issue of your vessel’s radio license, an MMSI(Maritime Mobile Service Identifier) must be requested. This isa nine digit number which must be permanently entered intothe RS87 when the radio is first set up, otherwise the DSCfunctions cannot be accessed.NOTE If the boat or the RS87 are subsequently sold, the radio mustbe returned to an authorised Simrad agent for the MMSI num-ber to be erased and the new owner’s MMSI number entered.For European leisure vessels fitted with VHF DSC equipment, aCEPT Short Range Certificate is required by the operator.Additional requirements, such as GOC or ROC may apply tooperators on commercial vessels. Please enquire with yourlocal licensing authority for full details.Refer to section 3.2.1 to enter the vessel’s MMSI number.1.5 Group ID MMSIFor boats that are part of a flotilla, racing fleet or other group, aGroup ID MMSI number can also be entered which will allowDSC communication within the group. Refer to section 3.2.3 toenter a Group MMSI number.Instruction Manual11Part No. E04297
2. MAIN FUNCTIONS2.1 General notesAlthough it has many advanced features, the RS87 has beendesigned to be as simple and intuitive to operate as possible.The Shift key is used to access the secondary functions printedabove each key - press and release Shift, then press the appro-priate key. These secondary functions are shown in this manu-al in italics (eg Group).NOTE The Shift key will automatically time out of Shift Mode after two seconds if another key is not pressed.At any time, pressing ON/C will cancel the current operation.The lowest occupied port is the master controller - thereforeany operations initiated on this handset will override all otherstations.CAUTION In order for other users to be able to operate the radio, it is imperative that the handset is replaced in the cradle after use.2.2 Switching on & Second Country modeTo turn the radio on, press the ON/C key. The display willshow the handset software issue number two seconds, then thestation number and software issue number for the transceiverunit for two seconds.As a default, the radio switches on tuned to the priority chan-nel (normally 16). If Last Channel Used mode has been set (seesection 3.3.3) the radio will switch on tuned to the previouslyused channel.The radio stores the previous volume and squelch settings andwill use these on startup.In countries where it is permitted, the RS87 can operate on asecondary set of channels, such as the USA channels.To select the secondary channel table, press Shift followed byOK. The display will show the channel set selected for twoseconds before reverting to the default display.NOTE Channels available will depend on programming. Please enquire with your national licensing authority for details ofpermitted channel sets in your own country.RS87 VHF12 Part No. E04297
2.3 Changing channelsTo select a channel, enter the channel number using the numer-ic keypad (Fig 2.1) -Instruction Manual13Part No. E04297Fig 2.1 - Selecting a channelIf the channel is invalid, the display will show “InvalidChannel” and then revert to the previous channel.The priority channel (normally 16) can be selected by pressing16, which will also set the radio to 25W transmit power.The preselected User Channel can be directly selected by press-ing the User key. The display will show “U” next to the chan-nel number to indicate that it is the User Channel (Fig 2.2).72VOLUME 05SQUELCH 03INTU 23VOLUME 05SQUELCH 03INT16VOLUME 05SQUELCH 03INTThe default setting for the User Channel is 16. Refer to section3.3.1 for details on setting the User Channel.Fig 2.2 - User channel selected
2.3.1 Channel SetsIn addition to the standard International Channel, the RS87 canalso be programmed with regional Auxiliary Channels, such asthe marina channels M and M2 in the UK, the USA weatherchannels and the fishing or leisure channels in Scandinavia.To display the channel sets available, press Shift followed by1W (Ch Set). Multiple presses of the 1W key while still in ShiftMode will scroll through the available channel sets.RS87 VHF14 Part No. E04297When the required channel set is displayed, enter the channelnumber using the numeric keypad - eg “2” for M2 (Fig 2.4) -MAR I NAAAAAMAR I NAAAAAINTPR I VATE AAAFig 2.3 - Selecting auxiliary channel sets(sets must be available to be displayed)Fig 2.4 - Selecting auxiliary channel numberThe only exception to this is when selecting UK marina chan-nel M, which has no number associated with it. Simply select-ing the marina channel set will automatically select it.NOTE If no numeric keys are pressed within two seconds the radio will revert to the previous working channel (except for marinachannel M as noted above).2MAR I NAAAAAINT
2.4 Volume adjustmentTo adjust the volume, press the VOL and VOL keys toincrease and decrease the setting respectively. Press and holdthe key to increase/decrease the setting rapidly.The volume setting can be between 1 and 24 (loud).2.5 Squelch adjustmentTo adjust the squelch setting, press the SQ key to enter squelchadjustment mode, then press the and (VOL) keys toincrease or decrease the squelch respectively. Press and holdthe key to increase/decrease the setting rapidly.The squelch setting can be between 0 (open) and 10.NOTE Squelch mode will automatically time out after two seconds if another key is not pressed. Squelch mode can also be cancelledby pressing the ON/C key.2.6 Dual Watch modeDual Watch allows the radio to scan between the selectedworking channel and the watch channel (the priority channel -normally 16).To enter Dual Watch, select the required working channel, thenpress Shift and 3(DW) within two seconds.If Dual Watch is selected while the handset is off cradle, thedisplay will show “Place back on cradle”. If the handset isreplaced within ten seconds of selecting Dual Watch, it willautomatically initiate Dual Watch when the handset isreplaced.The display will show “D/W” - the large digits on the displayindicate the working channel, with the watch channel shownbelow in small digits (Fig 2.5) -Instruction Manual15Part No. E042976D/WAAAAA 16BBBBBBBBBBINTDWFig 2.5 - Dual Watch mode
If the radio detects a signal on the watch channel, it will lockonto this and the large digits will change to show the watchchannel.NOTE All other stations will also show the Dual Watch display. NOTE Normal VHF functions will not be available when in Dual Watch mode. To exit Dual Watch press 16, ON/C or lift the handsetfrom the cradle.2.7 Tri Watch modeTri Watch allows the radio to scan between the selected work-ing channel, the user channel and the watch channel.NOTE Tri Watch cannot be selected if the user channel is set to Ch16.To enter Tri Watch, select the required working channel, pressShift and then press and hold the 3(DW) for two seconds.If Tri Watch is selected while the handset is off cradle, the dis-play will show “Place back on cradle”. If the handset isreplaced within ten seconds of selecting Tri Watch, it will auto-matically initiate Tri Watch when the handset is replaced.The display will show “T/W” - the large digits on the displayindicate the working channel, with the user channel and watchchannel shown below in small digits (Fig 2.6) -RS87 VHF16 Part No. E04297Press & holdT/WAAAAA 16USERBBBBB6INT 10Fig 2.6 - Tri Watch modeIf the radio detects a signal on the user or watch channels, itwill lock onto this and the large digits will change to show therelevant channel.NOTE All other stations will also show the Tri Watch display. NOTE Normal VHF functions will not be available when in Tri Watch mode. To exit Tri Watch press 16, ON/C or lift the handsetfrom the cradle.
If the radio locks onto a busy channel, pressing OK will manu-ally continue the scan. All Scan will otherwise automaticallyrestart when the channel becomes clear.NOTE All other stations will also show the All Scan display. NOTE While in scan mode, normal VHF functions are not available. To exit All Scan press 16, ON/C or lift the handset from thecradle.2.8.1 Dynamic All Scan InhibitIf the radio is constantly locking onto a busy channel whenscanning, this channel can be inhibited from the scan by press-ing Shift then 1while locked on that channel.The display will show “Channel Inhibited” and the channelwill no longer be included in the scan cycle.The channel can be reinstated using the menu option describedin section 3.1.1.2.8 All Scan modeThe scan function cycles the RS87 sequentially through eachenabled channel, pausing when a signal is detected.Press Shift followed by 1(Scan All) to enter All Scan Mode.If Scan is selected while the handset is off cradle, the displaywill show “Place back on cradle”. This function will be can-celled if the handset is not returned to the cradle within 10seconds.The display will show “Scan All” on the display. If the radiodetects a signal, it will lock onto this and the large digits willchange to show the relevant channel number (Fig 2.7) -Instruction Manual17Part No. E0429767INT SCANALLFig 2.7 - All Scan mode
2.9 Memory Scan modeMemory Scan gives the option of scanning a preprogrammedset of channels specified by the user (see sections 3.1.4 and3.1.5).Press Shift then 2(Scan M) to enter Memory scan mode.If Memory Scan is selected while the handset is off cradle, thedisplay will show “Place back on cradle”. If the handset isreplaced within ten seconds of selecting Memory Scan, it willautomatically initiate Memory Scan when the handset isreplaced.The display will show “Scan M” on the display. If the radiodetects a signal, it will lock onto this and the large digits willchange to show the relevant channel (Fig 2.8) -RS87 VHF18 Part No. E0429768INT SCANMFig 2.8 - Memory Scan modeIf the radio locks onto a busy channel, pressing OK will manu-ally continue the scan. Memory Scan will otherwise automati-cally restart when the channel becomes clear.NOTE If only one channel has been entered into the memory theninitiating Memory Scan will retune the RS87 to the storedchannel.NOTE All other stations will also show the Memory Scan display. NOTE While in memory Scan mode, normal VHF functions are not available. To exit Memory Scan press 16, ON/C or lift thehandset from the cradle.2.9.1 Dynamic Memory Scan DeleteIf the radio is constantly locking onto a busy channel whenscanning, this channel can be removed from the Memory Scanchannel set by pressing Shift then 2while locked on thatchannel.The display will show “Channel Deleted” and the channel willno longer be included in the scan cycle.
2.10 Adjusting backlightingThe display and keypad are backlit - to set the backlightinglevel press Shift followed by Call (Dimmer) to enter back-light mode.Use the and (VOL) keys to adjust the backlighting levelfrom off through to level 5..Press Ok or ON/C to exit the backlight mode at the selectedlevel.NOTE Backlighting levels will only affect this station.2.11 Handset off cradleWhen a handset is lifted off cradle, all other stations will show“Occupied” on the display (Fig 2.9). This means that these sta-tions are locked out until the handset is returned to the cradle,unless the station is being called on intercom by the handset.Instruction Manual19Part No. E04297NOTE The handset plugged into the lowest numbered port isdesignated the Master unit. Lifting the Master handset willoverride all other stations, even if it is displaying “Occupied” -all other stations will then display “Occupied” and be lockedout.STAT I ONAA2OCCUP I EDBBINT 16Fig 2.9 - Station 2 handset is in use
3. MENU MODEMenu mode is used to adjust the various settings of the radio,such as channels inhibited from the scan functions, MMSI num-ber programming and User channel selection.To enter Menu mode, press Shift followed by 9(Menu).Use the the VOL and VOL keys to scroll through thevarious menu options -- Scanning (section 3.1)Options related to the various scanning functions such aschannel inhibit, memory scan select and scan dwell time.- Numbers (section 3.2)Entering of ID numbers such as MMSI, Group MMSI andATIS number (if applicable in country of use).- VHF Items (section 3.3)Miscellaneous options such as selection of User channel,last used channel, interrupt intercom and speaker settings.To select an option, press Ok.To return to normal radio operation, press On/C.NOTE Entering Menu mode will inhibit the operation of the radio. Exit Menu mode before returning the handset to the cradle topermit normal operation.3.1Scanning Once the Scanning menu option has been selected (see intro-duction to section 3), use the VOL and VOL keys to scrollthrough the menu options -All Scan inhibit (section 3.1.1)All Scan reset (section 3.1.2)All Scan show (section 3.1.3)Memory Scan select (section 3.1.4)Memory Scan clear (section 3.1.5)Memory Scan show (section 3.1.6)Scan dwell time (section 3.1.7)To select an option, press Ok.To return to the main menu, press On/C.RS87 VHF20 Part No. E04297
3.1.1 All Scan inhibitIf the radio is constantly locking onto a busy channel whenscanning, this channel can be inhibited from the scan cycle.From the Scanning menu (see section 3.1) select All Scan Inhibitand press Ok.Enter the relevant channel number using the numeric keypad.The display will show the channel number and it’s inhibit status- “All Scan” for enabled, or “All Scan Inhibited” for inhibited(Fig 3.1) -Instruction Manual21Part No. E04297Press Ok to change the channel’s inhibit status - i.e if it isenabled, pressing Ok will inhibit it and vice versa. If the chan-nel is inhibited, it will no longer be included in the All Scancycle. Enabling the channel will re-include it.Additional channels can be inhibited/enabled by entering thechannel number and repeating the above procedure.To exit, press the VOL or VOL key to select anotherScanning menu option, or press On/C to return to the mainmenu.3.1.2 All Scan resetThis function will reset all inhibited channels so that they areenabled.From the scanning menu (section 3.1) select All Scan Reset andpress Ok - the display will show “Channels Reset” (Fig 3.2) -65ALL SCANAAINH IB ITEDBINTFig 3.1 - Selected channel inhibited from scanCHANNELSSSRESETEDBBBFig 3.2 - All inhibited channels resetPress the VOL or VOL key to select another Scanningmenu option, or On/C to return to the main menu.
Press Ok to change the channel’s Memory Scan status - i.e if itis not selected, pressing Ok will add it to the Memory Scancycle and vice versa.Additional channels can be added/removed by entering thechannel number and repeating the above procedure.Press the VOL or VOL key to select another Scanningmenu option, or On/C to return to the main menu.NOTE North American users - Only one Weather channel can be entered into Memory Scan - if another one is selected, it willoverride the existing channel. The Weather channel is notscanned as part of the Memory Scan sequence - it is used bythe Weather Watch function (see section 6.1).3.1.3 All Scan showThis function displays all the inhibited channels.From the scanning menu (section 3.1) select All Scan Show andpress Ok. The display will then show “Showing Channels”and display all the inhibited channels in sequence.Press the VOL or VOL key to select another Scanningmenu option, or On/C to return to the main menu.3.1.4 Memory Scan selectThis function selects the channels to be used in the MemoryScan cycle (see section 2.9).From the scanning menu (section 3.1) select Memory ScanSelect and press Ok - the display will show “Mem Scan Select”.Enter the relevant channel number using the numeric keypad.The display will show the channel number and it’s memory sta-tus - “Mem Scan” if it is not currently selected for MemoryScan, or “Mem Scan Enabled” if it is already selected (Fig 3.3) -RS87 VHF22 Part No. E0429765MEM SCANAAENABLEDBBINT65MEM SCANAAINTFig 3.3 - Selecting channel for Memory ScanCHANNEL CURRENTLY NOT SELECTED CHANNEL ALREADY SELECTED
3.1.5 Memory Scan clearMemory Scan Clear will reset all channels selected for MemoryScan so that they are disabled.From the scanning menu (section 3.1) select Memory ScanClear and press Ok - the display will show “Channels Cleared”(Fig 3.4) -Instruction Manual23Part No. E04297CHANNELSSSCLEAREDBBBFig 3.4 - Selecting channel for Memory ScanPress the VOL or VOL key to select another Scanningmenu option, or On/C to return to the main menu.3.1.6 Memory Scan showThis function displays all channels selected for Memory Scan.From the scanning menu (section 3.1) select Memory ScanShow and press Ok. The display will then show “ShowingChannels” and display all the Memory Scan selected channelsin sequence.Press the VOL or VOL key to select another Scanningmenu option, or On/C to return to the main menu.3.1.7 Scan dwell timeThis function is used to select the amount of time the RS87remains on a channel after it has locked onto it during a scan-ning function (All Scan, Memory Scan) and the signal is lost.From the scanning menu (section 3.1) select Scan Dwell Timeand press Ok - the display will show “Scan Dwell Time xx”,where xx is the current dwell time in seconds (Fig 3.5) -Fig 3.5 - Scan dwell timeSCAN DWELLT I ME 04The default time is 0, meaning that the scan will continue assoon as the signal is lost. There are 11 levels from 0-10 seconds- use the numeric keys to enter the scan dwell time and pressOk to select - the display will show “Dwell Time xx Seconds”.Press the VOL or VOL key to select another Scanningmenu option, or On/C to return to the main menu.
3.2 Numbers The Numbers menu is used for entering ID numbers such asMMSI, Group MMSI and ATIS (if applicable in country of use).Once the Numbers menu option has been selected (see intro-duction to section 3), use the VOL and VOL keys to scrollthrough the menu options -Ship’s MMSI (section 3.2.1)ATIS Number (section 3.2.2)Group MMSI (section 3.2.3)NOTE The ATIS Number option will only be shown if the radio is ATIS enabled. This feature is only available for sets used inBenelux and the Rhine/Danube waterways.To select an option, press Ok.To return to the main menu, press On/C.3.2.1 Ship’s MMSIShip’s MMSI will display the boat’s MMSI number if it hasalready been entered, or will allow the MMSI to be entered ifthe radio is being used for the first time.From the Numbers menu (section 3.2) select Ship’s MMSI andpress Ok - the display will show “Ships MMSI” and the MMSInumber (unless the number has not been entered yet, in whichcase it will show “_ _ _ _ _ _ _ _ _” - Fig 3.6).RS87 VHF24 Part No. E04297SH I PS MMS Ii------------INT 16Fig 3.6 - Entering MMSI NumberCAUTION The MMSI number can only be entered once and cannot be edited by the user. If it is necessary to change the MMSI (forexample if the radio is being moved to another boat), the radiomust be sent to an authorised Simrad service agent for repro-gramming.
To enter the MMSI number press Ok again. The display willshow ENTER MMSI and the first dash in the number will startflashing to indicate that entry can begin.Enter the nine digit MMSI number using the numeric keypadand press Ok. The radio will then ask that the MMSI is re-entered to confirm. If the two numbers do not match, theMMSI will need to be re-entered and re-confirmed.Use the Call and MSG keys to move the cursor to correctany errors. The cursor position is indicated by the number flash-ing. Enter a new number to overwrite the incorrect number.NOTE The MMSI number will not be accepted unless all 9 characters have been entered.Press the VOL or VOL key to select another Numbersmenu option, or On/C to return to the main menu.3.2.2 ATIS numberNOTE This section applies only to radios used in countries where the ATIS system is in operation (Benelux and the Rhine/Danubewaterways). This option will only appear on ATIS equippedradios.From the Numbers menu (section 3.2) select ATIS No. - thedisplay will show “ATIS No.” and the ATIS number (unlessthe number has not been entered yet, in which case it willshow “_ _ _ _ _ _ _ _ _”).CAUTION The ATIS number can only be entered once and cannot be edited by the user. If it is necessary to change the ATIS num-ber, the radio must be sent to an authorised Simrad serviceagent for reprogramming.To enter the ATIS number press Ok again. The display willshow ENTER ATIS and the first dash in the number will startflashing to indicate that entry can begin.Enter the nine digit ATIS number using the numeric keypadand press Ok. The radio will then ask that the number is re-entered to confirm. If the two numbers do not match, the num-ber will need to be re-entered and re-confirmed.Use the Call and MSG keys to move the cursor to correctany errors. The cursor position is indicated by the number flash-ing. Enter a new number to overwrite the incorrect number.NOTE The ATIS number will not be accepted unless all 9 digits havebeen entered - the prefix 9 is automatically inserted by the radio.Instruction Manual25Part No. E04297
Press the VOL or VOL key to select another Numbersmenu option, or On/C to return to the main menu.3.2.3 Group MMSIFor boats that are part of a flotilla, racing/fishing fleet or othergroup, a Group ID MMSI number can also be entered and usedto contact other boats in the same fleet.NOTE The Group MMSI number may be allocated on a temporary basis by the local administration, for this reason the numbercan be changed by the user.From the Numbers menu (section 3.2) select Group MMSI - thedisplay will show “Group MMSI” and the Group MMSI num-ber (unless the number has not been entered yet, in which caseit will show “0 _ _ _ _ _ _ _ _”).To enter the Group MMSI number press Ok again. The displaywill show ENTER MMSI and the first dash in the number willstart flashing to indicate that entry can begin.The first digit of a Group MMSI is always 0, and this is prese-lected by the radio. Enter the remaining 8 digits using thenumeric keypad and press Ok (Fig 3.7) -RS87 VHF26 Part No. E04297GROUP MMS II0436 1 ----INT 16Use the Call and MSG keys to move the cursor to correctany errors. The cursor position is indicated by the numberflashing. Enter a new number to overwrite the incorrectnumber.NOTE The number will not be accepted unless all 8 remaining digits have been entered.Press the VOL or VOL key to select another Numbersmenu option, or On/C to return to the main menu.Fig 3.7 - Entering Group MMSI number
Press the VOL or VOL key to select another VHF itemsmenu option, or On/C to return to the main menu.3.3 VHF itemsThe VHF items menu contains the settings for miscellaneousitems such as user channel, position view, auxiliary audio andspeaker settings amongst others.Once the VHF items menu option has been selected (see intro-duction to section 3), use the VOL and VOL keys to scrollthrough the menu options -User channel (section 3.3.1)Position view (section 3.3.2)Last used channel (section 3.3.3)Interrupt intercom (section 3.3.4)Auxiliary audio (section 3.3.5)Speaker settings (section 3.3.6)Scrambler codes (only if scrambler option is fitted)Serial numberTo select an option, press Ok.To return to the main menu, press On/C.3.3.1 User channelThis is a user programmable priority channel that is used in theTri-watch function and is selected by pressing the User key.From the VHF items menu (section 3.2) select User Channeland press Ok - the display will show “User Channel”.Enter the channel number using the numeric keypad and pressOk. The display will show “Set User Channel” (Fig 3.8) -Instruction Manual27Part No. E0429710SET USERAACHANNELBBBINTFig 3.8 - Setting the User Channel
From the VHF items menu (section 3.2) select Position View andpress Ok.If GPS position information is being received, the display willshow “Position View Off”. Press the Ok key to toggle betweenON and OFF. When this option is turned on, the bottom twolines of the display will show the current Lat / Long position onall handsets. If the volume or squelch is adjusted, the displaywill show the settings while the up/down keys are operated,before reverting to the position display.If no GPS position information is being received, the displaywill show “View”. Pressing Ok will show the manual positionentered, or the last known GPS position. If there has not been aposition entered, the Lat and Long display will show all 9’s.Press the VOL or VOL key to toggle between position andtime (UTC) displays.Press On/C to exit.3.3.3 Last used channelNormally the RS87 will power up on the programmed start upchannel (usually the priority channel). This function enables theradio to power up on the last used channel - the default setting is off.From the VHF items menu (section 3.2) select Last Used Chanand press Ok - the current status will be shown - “On” or “Off”.Press Ok to toggle between the On and Off settings.Press the VOL or VOL key to select another VHF itemsmenu option, or On/C to return to the main menu.3.3.2 Position viewThis option allows the user to view the current GPS position thatwill be used if a distress call is made (Fig 3.9). The function ofthis option depends on whether the position is being receivedautomatically via NMEA, or if it has been entered manually.RS87 VHF28 Part No. E042971689º 23. 000N102º 54. 120EINTLATLONFig 3.9 - Position display
3.3.4 Interrupt intercomThis function is used to specify whether intercom or loudhailerfunctions should be interrupted when an incoming VHF trans-mission is received - the default setting is “Yes”.From the VHF items menu (section 3.2) select InterruptIntercom and press Ok - the display will show “InterruptIntercom” and the current status - “Y” or “N”.Press Ok to toggle between Yes and No interrupt.Press the VOL or VOL key to select another VHF itemsmenu option, or On/C to return to the main menu.3.3.5 Auxiliary audioThe Auxiliary Audio input allows an outside audio source tobe connected to the radio and outputted through the speaker/intercom system (eg an FM receiver for weather forecasts etc).From the VHF items menu (section 3.2) select Auxiliary Audioand press Ok to enter the Auxiliary Audio sub-menu.Press the VOL or VOL keys to select the requiredAuxiliary Audio settings option -Use Aux AFInterrupt Aux AFTo turn the Auxiliary Audio input on, select “Use Aux AF” -the display will show “Use Aux AF” and the current status(“No” or “Yes”). Press Ok to toggle between the On and Offsettings. If the Aux AF option is switched on, the externalaudio source will be outputted through all speakers in the sys-tem at the set volume level.NOTE When this option is turned on, the display will show “Using Aux Audio” on the bottom line of the display. If the volume orsquelch is adjusted, the volume/squelch settings will be shownwhile they are being adjusted, then revert to this display.To specify whether the Auxiliary Audio input should be inter-rupted if an incoming VHF transmission is received select“Interrupt Aux AF” using the VOL or VOL key - thedefault setting is “Yes”.Press Ok to toggle between Yes and No interrupt.Press the VOL or VOL key to select another AuxiliaryAudio sub-menu option, or On/C to return to the VHF Itemsmenu. Press On/C again to return to the main menu.Instruction Manual29Part No. E04297
3.3.6 Speaker settingsThe Speaker Settings option is used to set the individualdefault volume levels for each station, intercom and loudhailerin the system.From the VHF items menu (section 3.2) select Speaker Settingsand press Ok to enter the Speaker Settings sub-menu. Pressthe VOL or VOL keys to scroll through each speaker, dis-playing the default volume level for each one.NOTE Only connected speakers will be shown.The first option in the sub-menu is Reset To Defaults (Fig 3.10) -pressing Ok when this option is displayed will reset all speakerlevels to their default settings - the display will show “ResettingLevels”.RS87 VHF30 Part No. E04297To set the required volume levels for each individual position,use the VOL or VOL keys to select the required stationand press Ok. The selected speaker will then emit a continu-ous tone indicating the current volume level. Press VOL orVOL to adjust the volume level as suitable and press Ok toconfirm.Press the VOL or VOL keys to select another station andrepeat the above procedure, or On/C to return to the VHFItems menu. Press On/C again to return to the main menu.16RESET TO000DEFAULTS00INTFig 3.10 - Resetting speaker settings to defaults
Enter the required working channel using the numeric keypad,or use the VOL or VOL keys to scroll through the fourdefault reply channels (06, 08, 72 & 77). Press Ok to confirm.NOTE Only simplex channels can be selected as the working channel.NOTE If the MMSI entered is for a coast station, the option to select a working channel will not be available - this is specified by thecoast station, and will normally be a duplex channel.The display will show “Press Ok To Send” - press Ok to initi-ate the call, or On/C to abort.4. DSC FUNCTIONS4.1General The RS87 features full Class D DSC (Digital Selective Calling)functionality, which enables the user to make digitally selectedcalls - quicker and simpler to make than traditional voice callsusing Channel 16. Should a distress situation occur, a DistressAlert call can be initiated, indicating the vessel’s identity, posi-tion and automatically establish distress communication on theemergency voice channel (normally Channel 16)NOTE DSC functions will only be available if the MMSI number has been entered into the radio (see section 3.2.1).4.2Making a call4.2.1 Individual Routine callPress the Call key to enter the Individual Routine call func-tion.Either manually enter the MMSI number of the station usingthe numeric keypad, or press the VOL and VOL keys toscroll through the MMSI number directory (Fig 4.1). Press Okto confirm the selected entry.Instruction Manual31Part No. E04297SEA M I STAAON CH 06 00INT 06Fig 4.1 - Selecting a number from the MMSI directory
On initiation of the call, the display will show “AwaitingAcknowledg” (Fig 4.2). Once an acknowledgement is received,the radio will automatically.switch to the specified workingchannel.RS87 VHF32 Part No. E04297NOTE If an acknowledgement is not received, the radio will continue showing the “Awaiting Acknowledg” display for 4.5 minutesbefore timing out and returning to normal operation.4.2.2 Public Correspondence callFor vessels within range of a country operating the necessarynetwork, the RS87 can be used to directly make and receivePublic Correspondence calls from a land based telephone sys-tem via a coast station.Press Shift then On/C to enter the Public Correspondence callfunction.Either manually enter the telephone number using the numerickeypad (Fig 4.3), or press the VOL and VOL keys to scrollthrough the telephone number directory. Press Ok to confirmthe selected entry.06AWA I T I NGAAACKNOWLEDGINTFig 4.2 - Call sent, awaiting acknowledgment from recipient0644 1 606547677------INTNOTE Check with your local network provider for usage instructions.Fig 4.3 - Dialling a number manually
The next stage is to specify the coast station the call is to berouted through. Either manually enter the MMSI number of thecoast station using the numeric keypad, or press the VOL andVOL keys to scroll through the Coast Station MMSI numberdirectory (Fig 4.4). Press Ok to confirm the selected entry.Instruction Manual33Part No. E0429706COAST 1 AAAINTNOTE The MMSI number entered must have two leading zeros(indicating a coast station), or it will not be accepted.The display will show “Press Ok To Send” - press Ok to initi-ate the call, or On/C to abort.On initiation of the call, the display will show “Attempting ToConnect”. If the call cannot be connected for any reason, thedisplay will show “Cannot Connect”, then “Pls Wait 15Minutes” before returning to the default display.If the call is connected, the display will show “Call InProgress” (Fig 4.5) - press the PTT key to talk and release tolisten.Fig 4.4 - Selecting a Coast Station from the coast station directoryNOTE The channel number displayed during the call is determined by the Coast Station.Press On/C to end the call, or wait for the other end to replacethe receiver.07CALL I N AAAPROGRESSBBINTFig 4.5 - Call has been connected
4.2.3 All Ships Safety callTo make an All Ships Safety call, lift the protective cover on thefront of the handset and press the Safety key. The display willshow “Safety on Ch 16” (Fig 4.6) -RS87 VHF34 Part No. E0429706SAFE T YAAAAON CH 16 00INTFig 4.6 - Making an All Ships Safety callEnter the required working channel using the numeric keypad,or use the VOL or VOL keys to scroll through the fourdefault reply channels (06, 08, 72 & 77). Press Ok to confirm.NOTE Only simplex channels can be selected as the working channel.The display will show “Press Ok To Send” - press Ok to initi-ate the call, or On/C to abort.4.2.4 All Ships Urgency callTo make an All Ships Urgency call, lift the protective cover onthe front of the handset and press the Urgency key. The dis-play will show “Urgency on Ch 16” (Fig 4.7) -06URGEN CYAAAON CH 16 00INTFig 4.6 - Making an All Ships Urgency callNOTE As All Ships Urgency calls must use Ch 16 for voice commun-ication, the option to manually select a working channel is notavailable.The display will show “Press Ok To Send” - press Ok to initi-ate the call, or On/C to abort.
4.2.5 Group callPress the Shift key twice to enter the Group call function - thedisplay will show the Group MMSI number stored in the radio(see section 3.2.3).Enter the required working channel using the numeric keypad,or use the VOL or VOL keys to scroll through the fourdefault reply channels (06, 08, 72 & 77). Press Ok to confirm(Fig 4.7) -Instruction Manual35Part No. E0429706026530 1 45ON CH 06BINTFig 4.7 - Making a Group CallNOTE Only simplex channels can be selected as the working channel.The display will show “Press Ok To Send” - press Ok to initi-ate the call, or On/C to abort.4.2.6 Distress Alert callWARNING This call should only be made if the vessel is in a genuinedistress situation. It is an offense to send a Distress Alert callif the vessel or crew are not in danger.The distress button is located under the protective cover on thefront of the handset. Press the Distress button to access theDistress Alert call function - the display will show “DistressUndefined” (Fig 4.8) ---D I STRESSAAUNDEF I NED bINTFig 4.8 - Distress Alert menuctd -
Use the VOL or VOL keys to scroll through the availableNature of Distress categories -• Undefined (default)• Abandoning• Piracy• MOB• Fire• Flooding• Collision• Grounding• Listing• Sinking• AdriftPress and HOLD the Distress key to begin the 5 second count-down - the large digits will count down from 5 to 1 before initi-ating the distress alert - the display will show “Sending Alert”(Fig 4.9) -RS87 VHF36 Part No. E04297NOTE The Distress Alert call can be aborted if the Distress key is released at any time before the 5 second countdown has ended.Press On/C to return to normal radio operation.The Distress Alert call sent includes the vessel’s MMSI, thenature of the distress as specified, the time the call was sentand the current position of the vessel (if the appropriate navi-gational receiver is connected to the radio, or a manual posi-tion has been entered - see section 6.3).The radio will switch to monitoring channel 16 and the displaywill show “Awaiting Acknowledg” until an acknowledgementis received. The radio will automatically repeat the Alertapproximately every four minutes until either an acknowl-edgement is received, or On/C is pressed (it is not recommend-ed that the Distress Alert is cancelled manually by pressingOn/C unless you are requested to do so by the rescue authori-ties). --SEND I NGAAAALER T BBBBBINTFig 4.9 - Sending a Distress Alert
When an acknowledgement is received from the Rescue Co-ordination Centre, this will automatically cancel the DistressAlert transmission. The subsequent rescue co-ordination willbe performed using the voice working channel (Ch 16).WARNING If a DSC distress alert is sent accidentally, cancel it immediately on the RD87 by pressing the On/C button to prevent repeats,then make the following announcement on channel 16 -“This is (name of vessel, callsign, MMSI)”“Cancel DSC Alert sent (date & time UTC)”Do not simply cancel the DSC alert without verbally cancellingit as well, otherwise the rescue authorities will not be awarethat this is a false alarm.4.3 Receiving a call4.3.1 Individual Routine callIf an Individual Routine call is received, the radio will soundan incoming call alarm.The display will flash between displaying “Call From”, thecaller’s MMSI and the specified working channel (Fig 4.10). Ifthe caller’s MMSI is stored in the MMSI directory (see section5.2), then the display will show the name stored instead of theMMSI number.Instruction Manual37Part No. E0429710CALL FROMA3453428599INTREPLY ONA0CH 0628599Fig 4.10 - Receiving incoming Individual Routine callPress Ok to accept the call or On/C to reject the call.If the call has been accepted, the display will show “SendAcknowledg”. Press Ok to send a call acknowledgement andautomatically switch to the specified working channel.
4.3.2 Public Correspondence callAPublic Correspondence call is a call made from a landbasedtelephone which is routed via a coast station. This is onlyavailable in countries operating the necessary network.NOTE At present, it is not possible to receive incoming calls on thePublic Correspondence network - calls can only be madefrom the radio. This section is for reference purposes only.When a Public Correspondence call is received the radio willsound an incoming call alarm.The display will flash between displaying “Tel Call From” andthe caller’s telephone number. If the caller’s number is storedin the Telephone Number directory (see section 5.3), then thedisplay will show the name stored instead of the telephonenumber (Fig 4.11) -RS87 VHF38 Part No. E0429710TEL CALLA0FROM428599INTSIMRAD ONA08599Fig 4.11 - Receiving incoming Public Correspondence callPress Ok to accept the call or On/C to reject the call - the dis-play will show “Call In Progress”.NOTE As the telephone call is transmitted via a VHF channelspecified by the coast station, it will still be necessary to pressthe PTT key to talk and release it to listen, as with a normalVHF call. The coast station will disconnect the call if the PTTis not pressed for 5 seconds at least every 45 seconds.To end the call, press the On/C key, or wait until the callerreplaces the receiver (an End Call signal will be sent to theradio). Replace the handset in the cradle.
Press Ok to accept the call and automatically switch to channel16, or On/C to reject the call.NOTE All Ships Urgency calls always use channel 16 as the working channel.4.3.3 All Ships Safety callIf an All Ships Safety call is received, the radio will sound anincoming call alarm.The display will flash between displaying “All Ships Safety”and the caller’s MMSI. If the caller’s MMSI is stored in theMMSI directory (see section 5.2), then the display will show thename stored instead of the MMSI number.Press Ok to accept the call - the display will change to “ReplyOn Ch X”, where X is the specified working channel, or On/Cto reject the call.Press Ok again to automatically switch to the working channel.4.3.4 All Ships Urgency callIf an All Ships Urgency call is received, the radio will sound anincoming call alarm.The display will flash between displaying “All Ships Urgency”and the caller’s MMSI. If the caller’s MMSI is stored in theMMSI directory (see section 5.2), then the display will show thename stored instead of the MMSI number (Fig 4.12) -Instruction Manual39Part No. E0429710ALL SHIPSSSURGENCY9 9INTFROMPRAY 0 SEASPRAY 0Fig 4.12 - Incoming All Ships Urgency call
Press Ok again to automatically switch to the workingchannel.4.3.5 Group callIf the radio has a Group MMSI number entered (see section3.2.3) and a Group call is received, the radio will sound anincoming call alarm.The display will flash between displaying “Routine GroupCall” + the caller’s MMSI and the specified working channel(Fig 4.13). If the caller’s MMSI is stored in the MMSI directory(see section 5.2), then the display will show the name storedinstead of the MMSI number.RS87 VHF40 Part No. E0429706ROUT I NESSGROUP CALLINTFROMPRAY 0 3895623970Fig 4.13 - Incoming Group callFig 4.14 - Working channel specified by incoming Group callPress Ok to accept the call - the display will change to “ReplyOn Ch X” (Fig 4.14), where X is the specified working channel,or On/C to reject the call.06REPLY ONAACH 1 0BBBBBINT
4.3.6 Distress Alert callIf a Distress Alert call is received, the radio will sound anincoming call alarm.The display will flash between displaying “Distress Alert” andthe caller’s MMSI along with the nature of the distress alert.If the caller’s MMSI is stored in the MMSI directory (see section5.2), then the display will show the name stored instead of theMMSI number (Fig 4.15) -Instruction Manual41Part No. E0429706D I STRESS SALERT CALLINTS I NK I NG 03453428599Fig 4.15 - Incoming Distress Alert callPress Ok to accept the call and automatically switch to channel16, or On/C to reject the call.The full details of the Distress Alert may be viewed in the log(see section 4.4).NOTE Distress Alert calls always use channel 16 as the working channel.
4.3.7 Distress Alert acknowledgementIf an acknowledgement is received for a Distress Alert sent(normally from a coast station or rescue co-ordination centre),the radio will sound an incoming call alarm.The display will flash between displaying “DistressAcknowledg” and the MMSI of the vessel in distress, or yourMMSI if the Distress Alert was sent by the RS87 and theDistress Alert transmission sent has been cancelled.If the vessel’s MMSI is stored in the MMSI directory (see sec-tion 5.2), then the display will show the name stored instead ofthe MMSI number (Fig 4.16) -RS87 VHF42 Part No. E0429706D I STRESS SACKNOWLEDGINTFORK I NG 0ROBERTA00Fig 4.16 - Distress Acknowledgment receivedNOTE The MMSI / name displayed will be that of the vessel indistress, not the station that has acknowledged the call.Press Ok to accept the acknowledgment and automaticallyswitch to channel 16, or On/C to ignore the call.NOTE Distress Alert calls always use channel 16 as the working channel.
4.3.8 Distress Relay callThe Distress Relay facility enables an incoming Distress Alertcall to be passed onwards via boats within receiving distance ofthe call, thus increasing the potential range of the Distress Alertcall.If a Distress Relay call is received, the radio will sound anincoming call alarm.The display will flash between displaying “Distress Relay”and the vessel’s MMSI (Fig 4.17) -Instruction Manual43Part No. E0429706D I STRESS SRELAY ALLINTFOR I NG 03453428599Fig 4.17 - Incoming Distress RelayIf the vessel’s MMSI is stored in the MMSI directory (see sec-tion 5.2), then the display will show the name stored instead ofthe MMSI number.NOTE The MMSI / name displayed will be that of the vessel indistress, not the vessel that relayed the call.Press Ok to accept the call, automatically switch to channel 16or On/C to reject the call.
4.4 Viewing the Call LogThe call log records details of the last 20 DSC or telephone callsreceived including the date and time received, the type of calland the caller id. There are two separate logs - one for “stan-dard” calls, the other for distress calls.NOTE All calls are logged, even those rejected by pressing On/C.Press MSG enter the Call Log menu. If the call logs areempty the display will show “No Calls Received” beforereturning to the default display.Press the Call and MSG keys to switch between the stan-dard call log (indicated by “1” shown next to the large digits)and the distress call log (indicated by “2” shown next to thelarge digits).Press VOL or VOL to scroll through the log entries - the dis-play will show the call type and the date/time the call wasreceived (Fig 4.18). The small digit shows the log type (1 - stan-dard call log, 2 - distress call log) and the large digits show theentry number - the first entry shown is the most recent call.RS87 VHF44 Part No. E042971 03I ND I V I DUAL1 9- 1 2 1 452MSGINTFig 4.18 - Viewing Call Log entryNOTE The date and time displayed uses the date/time data received from the navigational receiver interfaced to the radio, not fromthe incoming message. If a navigational receiver was not con-nected to the radio at the time the message is received the dateand time will not be displayed.Press Ok to view the details of the selected call - the displaywill show the caller’s number (Or the name if the number isstored in the directory).
Press VOL or VOL to display any relevant additionalinformation - for example the nature of distress and position ofthe vessel in distress if viewing the distress call log (Fig 4.19) -Instruction Manual45Part No. E04297207D I ST ALERT1 4- 1 0 0937MSGINTFig 4.18 - Viewing Call Log entryS I NK I NG 03453428599LA 56-52NLO 009-50EPress On/C to return to the log entries menu. Press On/Cagain to exit the Call Log menu.4.5 Position over 4 hours oldNormally current position data is supplied automatically tothe radio via an interfaced navigational receiver (see section7.2.7) or by manually entering a position (see section 6.3). Ifthe last recorded position is over 4 hours old, the display willshow “Position 4 Hours Old”. Press Ok to confirm and man-ually enter a position (refer to section 6.3) or On/C to ignorethe message.NOTE This display will be shown 30 minutes after switch on if there is no NMEA position data being received, or the position hasnot been manually entered.
5. THE DIRECTORYThe Directory function allows frequently used boat MMSI,Coast Station MMSI and telephone numbers to be stored in theradio. To enter the directory, press Shift then MSG (Dir).5.1 Switching between the directoriesThe large digits will show the currently displayed entry num-ber and the smaller digit to the left of the large digits will showthe currently selected directory -1. Boat MMSI directory2. Telephone number directory3. Coast Station MMSI directoryPress Call and MSG to switch between the directories.5.2 Viewing the directorySelect the appropriate directory using the Call and MSGkeys. Use the VOL or VOL keys to scroll through thedirectory entries (Fig 5.1) -RS87 VHF46 Part No. E04297101SEASPRAY 0475394270DIRINT102ROBERTAY 09463872 1 5DIRINTFig 5.1 - Scrolling through the directory entries
Use the numeric keypad to enter the number (Fig 5.3). Press theCall and MSG keys to move the cursor to correct any errors.The cursor position is indicated by the number flashing - enter anew number to overwrite the incorrect number.5.3 Entering a numberPress Ok to begin entering a new number - the large digits willshow the entry number in the directory (1 if it is the first entry).Enter the name first - use the VOL or VOL keys to scrollthrough the alphabetical characters and the numeric keypad toenter any numbers (Fig 5.2)Press MSG to move the cursor forward, or Call to moveback and correct any errors (The cursor position is indicated bythe character flashing - enter a new character to overwrite). Press Ok to confirm the entry and move on to the MMSI entry.Instruction Manual47Part No. E042971 0 1SEASP---------------DIRINTFig 5.2 - Entering a new name into the directory1 0 1SEASPRAY 047539-----DIRINTFig 5.3 - Entering the numberPress Ok to confirm and store the entry to the directory.Press On/C at any time to abort to the default display.NOTE If using the Boat or Coast Station directories the entry will not be accepted unless all nine digits of the MMSI number havebeen entered.
5.4 Editing a numberSelect the directory entry to be edited and press Ok. Use theVOL or VOL keys to highlight either the name or thenumber for editing - the selected field will flash. Press Okagain to begin editing the selected field.Use the Call and MSG keys to move the cursor - the cursorposition is indicated by the character flashing. Enter a new char-acter to overwrite - use the numeric keypad to enter a number,or press VOL or VOL to scroll through the alphabeticalcharacters (Fig 5.4) -RS87 VHF48 Part No. E04297101SEASPRAY 0475394270DIRINT101SEASP-----475394270DIRINTFig 5.4 - Editing an existing directory entrySelectedfield willflashPress Ok to confirm and store the edited entry or On/C toabort entry.
6. MISCELLANEOUS FUNCTIONS6.1 Selecting Weather WatchThe Weather Watch function enables the radio to monitor a sin-gle Weather channel specified in the Memory Scan Select func-tion (see section 3.1.4). A transmission on a Weather channel ispreceded by a tone - if this is detected by the radio, it will soundan alert allowing the user to switch to the Weather channel.To enable Weather Watch, press Shift followed by the User key(Wx Watch). The“WX” legend will be shown in the top left ofthe display and the selected weather channel will be shown onthe bottom line of the display (Fig 6.1) -Instruction Manual49Part No. E0429712WEA T HERAAAWATCHBBBW4WXFig 6.1 - Selecting Weather Watch modeNOTE If a Weather channel has not been specified, the display will show “No Wx Chan Selected” and Weather Watch will not beenabled. Refer to section 3.1.4 to select a Weather channel.NOTE If the Weather Watch function is not available (for example, if no Weather channels are programmed into the radio), the dis-play will show “Wx Not Enabled”.To cancel Weather Watch, press Shift followed by the User key(Wx Watch).6.1.1 Weather Watch alertIf a Weather Alert tone is detected by the radio on the specifiedWeather channel while Weather Watch is enabled, the radiowill sound a 10 second alarm and the display will show“Weather Alert”.Press Ok to cancel the alarm and switch to the Weather chan-nel, or On/C to cancel the alarm and ignore the Weather Alert.NOTE Because the Weather channels transmit a continuous carrier signal, it is not possible for the RS87 to detect when the trans-mission has ended.Press On/C to return to the working channel once the trans-mission has ended.
6.2 Security mode (voice scrambler)For additional security, a voice scrambler function is availableas an optional accessory. The scrambler uses frequency inver-sion to encrypt the transmission and will allow secure trans-mission between compatible radios.To enable Security mode press Shift followed by 0 (Scrm). Thedisplay will show “Sec” indicating that Security mode is on.To exit Security mode, press Shift followed by 0 (Scrm) again,or press On/C. Security mode will be cancelled if the RS87 isplaced into another mode that requires the use of the PTT key(i.e Hailer/Intercom) or if a DSC call is made/received.6.3 Editing Latitude, Longitude and UTCNormally, position and time data should be supplied to theRS87 via a GPS or other navigational device connected to theradio. However, if this is not possible, the position and timecan be entered manually -Press Shift then 8(Lat/Lon). The display will show “Enter Lat”.Enter the Latitude using the numeric keypad (Fig 6.2). Use theCall and MSG keys to move the cursor to correct anyerrors. The cursor position is indicated by the number flashing.Enter a new number to overwrite the incorrect number.RS87 VHF50 Part No. E0429712ENTER LA T ALA 52-B---INTFig 6.2 - Manually entering positionThe final digit specifies whether the Latitude is north or southof the Equator - press VOL or VOL to toggle between Nand S.Press Ok to confirm and move on to entering the Longitude -the display will show “Enter Long” - or On/C to abort entry.Enter the Longitude using the numeric keypad. Use the Calland MSG keys to move the cursor to correct any errors. Thecursor position is indicated by the number flashing. Enter anew number to overwrite the incorrect number.
The final digit specifies whether the Longitude is west or eastof the Meridian - press VOL or VOL to toggle between Wand E.Press Ok to confirm and move on to entering the time - the dis-play will show “Enter UTC” - or On/C to abort entry.Enter the UTC time (formerly known as GMT) in 24hr formatusing the numeric keypad (Fig 6.3). Use the Call and MSGkeys to move the cursor to correct any errors. The cursor posi-tion is indicated by the number flashing. Enter a new numberto overwrite the incorrect number.Instruction Manual51Part No. E04297Press Ok to confirm all settings or On/C to abort entry.WARNING This data is only stored temporarily and will be lost when the radio is switched off. Since the accuracy of this information isvital in the event of a Distress Alert transmission being neces-sary, we strongly recommend that a GPS or other navigationaldevice is permanently interfaced with the radio. This data willthen be automatically supplied and updated without the needfor user intervention.6.4 Toggling between Lat/Long and UTC viewsIf the Position View option (see section 3.3.2) is turned on, thecurrent position will be displayed on the bottom two lines ofthe display.The UTC time can be displayed instead by pressing Shift thenholding the 8(Lat/Lon) key down for two seconds (Fig 6.4) -12ENTER U T CAUTC 19B----INTFig 6.3 - Manually entering time (UTC)UTC 19B26-Fig 6.4 - Displaying UTC timeRepeat the above key sequence to toggle between the Positionand Time displays.
6.5 IntercomIf the system comprises of more than one station and/orincludes intercom speaker/s, it is possible to make an intercomcall to a selected position from a handset.NOTE This assumes that the installation comprises a full expanded RS87 system with four stations and two intercom speakers.The options shown will only be available if the relevant sta-tions / intercoms are installed.6.5.1 Making an intercom callPress Shift then 6 (Intercom) to enter Intercom mode. The dis-play will show “Intercom Stn X - Stn Y”, where “X” is the I/Dof the current station being used and “Y” is the first of theother stations in the system (Fig 6.5) -RS87 VHF52 Part No. E04297Press the VOL and VOL keys to scroll through the avail-able stations / intercoms that can be called from the station -“Stn 1–Stn 2” Intercom call to Station 2“Stn 1–Stn 3” Intercom call to Station 3“Stn 1–Stn 4” Intercom call to Station 4“Int Spkr 1” Intercom call to Intercom speaker 1“Int Spkr 2” Intercom call to Intercom speaker 2“All Spkrs” Intercom call to all Station speakers“P A” Intercom call to all speakers in system(including horns)Press the PTT key or Ok to activate the intercom or pressOn/C to cancel. Once the call has been initiated, further press-es of the Ok key will re-sound the call alarm. Pressing thePTT key will open the audio path to the called station.NOTE The call will be terminated if it is not accepted within 15 secs.12I N T ERCOMAASTN 1 -STN2 BINTFig 6.5 - Making an intercom call to station 2 from station 1
If calling an Intercom speaker, pressing the VOL and VOLkeys while the PTT key is held to adjust the Intercom speakervolume. This option is not available if calling another Stationor making an All Speaker / PAcall - the current volume set-tings for each position will be used.To end the intercom call, press On/C or return the handset toits cradle.NOTE While making an intercom call, all other stations will display “Station X Occupied”.NOTE If the Interrupt Intercom option (section 3.3.4) is disabled and a VHF transmission is being received, the display will show“Signal Present” until the transmission has ended. If InterruptIntercom is enabled, the intercom call will be interrupted if aVHF transmission is received.6.5.2 Receiving an intercom callIf an intercom call is received from another station, the displaywill show “Intercom From Stn Y”, where “Y” is the I/D of theStation making the intercom call (Fig 6.6) -Instruction Manual53Part No. E04297If the other station is making an All Speakers call, the displaywill show “Int All From Stn Y”.If the other station is making a PA call, the display will show“P A from Stn Y”.To accept the call lift the handset from the cradle or press On/Cto cancel the intercom call.To end the intercom call, press On/C or return the handset toits cradle.NOTE All speaker and PA calls are announcement calls and therefore do not need to be accepted manually by the receiving stations.12I N T ERCOMAAFROM STN 22INTFig 6.6 - Receiving an intercom call from station 2
6.6 Loudhailer / FoghornUp to two loudhailer / foghorns can be fitted to the RS87 - oneFore and one Aft.To enter Hailer / Foghorn mode press Shift then 5(Hail/Fog).The display will show “Loudhailer Fwd” (Fig 6.7) -RS87 VHF54 Part No. E0429712LOUDHA I LERFWDM STN 22INTFig 6.7 - Selecting Foghorn modeTo toggle between Loudhailer and Foghorn press the 5key -the display will show “Foghorn Fwd”.NOTE If no hailers are connected to the radio the display will show “Horns not enabled”.6.6.1 LoudhailerTo cycle through the loudhailer options press the 4 key -Loudhailer FwdLoudhailer AftLoudhailer BothNOTE If a single loudhailer is fitted, only the “Loudhailer Fwd” or “Loudhailer Aft” option will show, depending on where fitted.Press the PTT key to make the loudhailer call. Press theVOL and VOL keys while the PTT is pressed to adjust thehailer volume.Press Ok to open the talkback path, enabling users at the loud-hailer to talk back.Press the On/C key to exit Loudhailer /Foghorn mode.NOTE If Interrupt Intercom is disabled (see section 3.3.4) the display will show “Signal Present” if an incoming VHF transmission isbeing received.
6.6.2 FoghornTo select Foghorn press the 5key while in Loudhailer /Foghorn mode - the display shows “Foghorn Fwd” (Fig 6.8) -Instruction Manual55Part No. E04297To cycle through the foghorn options press the 4 key -Foghorn FwdFoghorn AftFoghorn BothNOTE If a single loudhailer is fitted, only the “Foghorn Fwd” or “Foghorn Aft” option will show, depending on where fitted.Press Ok to enter the Foghorn sub menu. Use the VOL andVOL keys to scroll through the available horn tone options -HornSirenPower Vessel Under WayPower Vessel StoppedRestricted ManoeuvreWorking at anchorVessel Being TowedVessel In PilotageAnchorAgroundPress PTT or Ok to sound the horn. If an external horn buttonis fitted to the radio, pressing this will also sound the horn. NOTE For single activation options (eg Horn), it is necessary to press the activation button each time to sound the horn. For auto-matic repeat options (eg Anchor) it is only necessary to pressthe key once and the foghorn will sound automatically. PressOn/C to cancel the automatic repeat sequence.Adjusting horn volume - for single activation options press theVOL and VOL keys while the PTT is pressed. For auto-matic repeat options, press VOL and VOL while the dis-play shows “Horn In Use”. ctd -12FOGHORN AAFWDM STN 22INTFig 6.8 - Selecting Foghorn mode
Press the On/C key to exit Loudhailer /Foghorn mode.NOTE Ten seconds after the automatic horn is sounded the unit will revert to normal radio operation, but the horn will continue tosound. To cancel, press Shift followed by 5(Hail/Fog), thenOn/C.6.7 Station speaker muteThe station speaker that is installed alongside the handset canbe muted if required.To mute the speaker, press Shift followed by 7(Speaker) on thespecific handset that is used with the speaker.To disable mute, press Shift followed by 7(Speaker) again, theVOL and VOL keys or lift the handset from the cradle. Ifthe system is powered down, the speaker will be un-mutedwhen the system is turned on again.NOTE This will only affect the speaker that is used with this specific handset - eg handset 1 will only mute the speaker connected tothe Station 1 terminals. To mute any other speakers on the sys-tem it will be necessary to go to the relevant handset and selectmute.6.8iDSC The RS87 can be integrated with one of Simrad’s navigationaldisplays (33, 42 and 52 series) enabling details of any incomingDSC calls to be displayed on the unit. Refer to the instructionmanual of the relevant unit for more details. Refer to section7.2.5 for interfacing details.RS87 VHF56 Part No. E04297
7 INSTALLATION7.1 Physical InstallationThe RS87 is a modular system that is very simple to install,however the performance of the radio is directly affected by thequality of the installation. Please read these instructions thor-oughly before attempting installation and if in any doubt, con-sult a qualified marine electronics engineer.7.1.1 Transceiver InstallationThe transceiver unit is designed to be installed in a concealedlocation such as in a locker or behind the switch panel.CAUTION The transceiver unit is not waterproof, therefore it must not beinstalled in any location where it is likely to be exposed toexcess moisture (eg a wet locker or an outside locker).The fins on the top of the transceiver act as a heatsink to dissi-pate heat generated by the set when in use, which maintainsthe high efficiency of the radio. The free circulation of air isessential - if mounting the transceiver in an enclosed space,ensure that the space is well ventilatedThe transceiver requires a flat surface with an area of at least170 x 245mm (6.8 x 9.8in) for mounting. Allow sufficient spacebeneath the unit to allow cable entry - at least 50mm (2.0in) isrecommended. The surface should be rigid and sturdy enoughto be able to support the weight of the unit, taking into accountthe shock loads likely to be encountered when the vessel isunderway in heavy seas.Fix the transceiver unit to the surface using the four self-tap-ping screws supplied. The four fixing points are at the cornersof the transceiver unit -the bottom two are underneath the ter-minal cover (Fig 7.1) -Instruction Manual57Part No. E04297Fig 7.1 - Transceiver box mounting
7.1.2 Handset InstallationThe handset should be sited so that engine noise and vibrationor other background noise do not make it difficult for the oper-ator to hear.As microphones and loudspeakers contain powerful magnets,the handset and speakers should not be installed within 1m(3ft 3in) of any compasses, whether magnetic or electronic.The handset is connected to a 5m (16.5ft) extension cable, there-fore the handset should be fitted within reach of the transceiverbox (for longer runs, 20m extension cables are also available asseparate accessories - see section 8.6).The handset cradle should be mounted on a flat surface withenough space to allow the bulkhead socket for the extensioncable to be fitted alongside. Space should also be allowed near-by for the accompanying loudspeaker to be fitted.NOTE The handset and bulkhead socket are waterproof, but if the handset is to be fitted in an exposed location (for example onthe flybridge of a power boat) it is recommended that thehandset and especially the bulkhead socket is fitted to anangled or vertical surface to prevent standing water lying onthe handset face or inside the bulkhead socket, which couldcorrode the pins.Fit the supplied template for the handset cradle to the desiredmounting location. Drill 4 x3.2mm (0.125in) pilot holes in theindicated positions. If drilling into GRP, it is recommendedthat the holes are also countersunk to prevent the gelcoat split-ting when the self-tapping screws are inserted.Fit the supplied template to the desired mounting location forthe bulkhead socket. Drill a 23.5mm (0.94in) hole and 4 x2.4mm (0.1in) pilot holes. Again, the pilot holes should becountersunk if drilling into GRP.Fit the bulkhead socket and run the cable to the transceiver boxposition.NOTE It is recommended that the cable is routed away from any other cables carrying high current (eg mains power cables) or pulsedsignals (eg transducer cables) to avoid possible interference.If the handset is being removed, the waterproof cover shouldalways be fitted to the bulkhead socket to protect the pins frompossible corrosion.RS87 VHF58 Part No. E04297
7.1.3 Station speaker InstallationThe loudspeaker should be installed near to the handset and canbe flush mounted or surface mounted with the supplied pattress.Flush Mounting Attach the self adhesive gasket to the back of the loudspeaker. Remove the four detachable corners of the speaker which con-ceal the mounting holes. Apply the supplied cutting templateto the mounting position. Carefully cut out the aperturerequired for the speaker back and use the short self tappingscrews provided. Refit the corners to conceal the screw fixings.Surface Mounting Drill a 5mm (0.2in) hole for the speaker cable. Attach the self adhesive gasket to the back of the loudspeaker. Remove thefour detachable corners which conceal the mounting holes. Fitthe pattress to the back of the speaker and use the long self-tap-ping screws provided to fix the speaker and the pattress blockto the bulkhead. Refit the corners to conceal the screw fixings.7.2 Electronic InstallationElectronic installation is straightforward - all peripherals con-nect to the Transceiver Unit using the clearly labelled plug-interminals (Fig 7.2) -Instruction Manual59Part No. E04297Fig 7.2 - Transceiver terminal connectionsNOTE The diagram shows the terminal bay with the optional expan-sion board, which is not included with the standard radio.If it is necessary to shorten any of the cables, ensure the endsare re-tinned for the best quality connection.The transceiver unit is fitted with a 10amp “blade” type fuse.It is recommended that the radio is connected to a 10ampfused switch or breaker on the boat’s switch panel.Connect the supplied power cable to the terminals markedPWR + and - as follows -STANDARD CONNECTIONS EXPANSION BOARDTerminalNumber12WireColour(s)RedBlack
7.2.1 Control panelAsingle cable links the control panel to the transceiver unit.The standard model can support up to two control stations, orup to four stations if the expansion board is fitted. One fixedstation is supplied with the radio - additional stations are sup-plied as separate accessories. The control stations can be eithera handset model which is supplied with a separate loudspeak-er or a fixed control panel with a passive fistmike or handset.Connect the main control station to the “Station 1” terminals onthe transceiver unit as shown (Fig 7.3) -RS87 VHF60 Part No. E04297TerminalNumber12345678WireColour(s)BrownGreenRedWhiteBlueYellowOrangeBlackAdditional control stations should be wired in the same man-ner and connected to the “Station 2”, “Station 3*” and “Station4*” terminals (Fig 7.5).* Only available on models fitted with the expansion boardFig 7.4 - Control panel terminal connectionsStation 2Station 1Station 4*Station 3*Fig 7.5 - Example of a typical multi-station installation
7.2.2 LoudspeakersThe RS87 can be fitted with Simrad LS80 station speakers orthird party station speakers with an impedance of 4Ω.Connect the station speaker to terminals 7 and 8 of a freeStation terminal strip (Fig 7.6).Instruction Manual61Part No. E04297TerminalNumber78WireColour(s)OrangeBlackFig 7.6 - Station loudspeaker terminal connections7.2.3 IntercomsNOTE Only available on units fitted with the expansion board.The RS87 intercoms enable two-way onboard communicationwith the main stations but do not allow control or use of VHFor DSC functions. Intercoms are normally fitted in areas suchas the engine room, galley or crew quarters. Up to two inter-coms can be fitted to the RS87.Connect the intercoms to the “Int 1” and “Int 2” terminals onthe transceiver unit as shown (Fig 7.7) -Fig 7.7 - Intercom terminal connectionsTerminalNumber123WireColour(s)BlackRedWhite
7.2.4 Loudhailer/FoghornsNOTE Only available on units fitted with the expansion board.Two separate loudhailer/foghorns can be fitted to the RS87(normally one is mounted on the fore of the boat, the other aft).Connect the loudhailers to the “Aft/Fwd Hailers” terminals onthe transceiver unit as appropriate (Fig 7.8) -RS87 VHF62 Part No. E04297TerminalNumber1234WireColour(s)Aft +Aft -Fore +Fore -Fig 7.8 - Loudhailer terminal connectionsWARNING Do not connect any of these terminals to a common ground,otherwise the RS87 will be permanently damaged.7.2.5 Remote foghorn buttonNOTE Only available on units fitted with the EHX80 expansion board.Aremote button can be used to activate the foghorn. Connectthe remote button to the terminals marked “Horn Key” asshown (Fig 7.9) -TerminalNumber12WireColour(s)RedBlueFig 7.9 - Remote foghorn button terminal connectionsNOTE Apart from when transmitting, pressing this button will enable the foghorn to be sounded at any time, regardless of whatmode the RS87 is currently in.
7.2.6 Auxiliary audio inputNOTE Only available on units fitted with the EHX80 expansion board.The expansion board upgrade on the RS87 allows an auxiliaryaudio input - for example from a radio receiver or an entertain-ment system - to be fed into the intercom / loudspeaker system.The auxiliary input must be a line level signal (0.775V rms)Connect the line out from the auxiliary source to the terminalsmarked “Aux AF” as shown (Fig 7.10) -Instruction Manual63Part No. E042977.2.7 NMEA0183 inputThe inbuilt NMEA0183 processor allows navigational positioninformation to be received from a GPS or Chart Plotter. Theboat’s position is automatically transmitted when a DistressAlert is initiated.NMEA input must be of the 0183 format, version 2.0 - 3.0, out-putting sentences GLL, RMC and ZDA at a Baud rate of 4800.The NMEA Out connections from the GPS/Plotter should beconnected to the “NMEA In” terminals as shown (Fig 7.11) -TerminalNumber12WireColour(s)Line Out +Line Out -Fig 7.10 - Auxiliary audio input terminal connectionsTerminalNumber12WireReferenceCommon Out -Data Out +Fig 7.10 - Auxiliary audio input terminal connections
7.2.8 iDSC outputThe RS87 is designed to integrate with other Simrad equipmentwhich enables DSC call information to be displayed on thexx33, xx42 and xx52 series chartplotters.Connect the iDSC input terminals of the chartplotter to the ter-minals marked “iDSC” as shown (Fig 7.11) -RS87 VHF64 Part No. E04297TerminalNumber34WireReferenceiDSC -iDSC +Fig 7.11 - iDSC output terminal connections7.2.9 Future optionsThe two circular ports in the centre of the connection panel arereserved for future options (Fig 7.12) -Fig 7.12 - Future optionsReservedfor futureoptions
7.2.10 SummarySummary of the RS87 connections -Instruction Manual65Part No. E04297STANDARD CONNECTIONS EXPANSION BOARDTerminalNumber12345678WireColour(s)BrownGreenRedWhiteBlueYellowOrangeBlackTerminalNumber123WireColour(s)BlackRedWhiteTerminalNumber1234WireColour(s)Aft +Aft -Fore +Fore -TerminalNumber12WireColour(s)RedBlueTerminalNumber12WireColour(s)Line Out +Line Out -Station 1TerminalNumber12345678WireColour(s)BrownGreenRedWhiteBlueYellowOrangeBlackStation 2TerminalNumber12345678WireColour(s)BrownGreenRedWhiteBlueYellowOrangeBlackStation 3TerminalNumber12345678WireColour(s)BrownGreenRedWhiteBlueYellowOrangeBlackStation 4 Fog/HailersTerminalNumber1234WireReferenceCommon Out -Data Out +iDSC -iDSC +NMEA/iDSCIntercoms (Int1/Int2)Horn Key Aux AFTerminalNumber+-WireReferenceRed (12v in)Black (0v)PWRSTANDARD CONNECTIONSEXPANSION BOARD CONNECTIONSFig 7.13 - Transceiver unit connections summary
7.2.11 Cable strain reliefOnce all the cables have been run to the appropriate peripher-als and connected to the transceiver unit they should besecured to ensure that they are not snagged or exposed toexcess strain.Screw the strain relief tabs to the cable exit port on the trans-ceiver unit using the screws supplied and secure the cables tothe tabs using tie wraps as shown (Fig 7.14) -RS87 VHF66 Part No. E04297Replace the terminal cover and secure by tightening the retain-ing screw.7.3 Antenna installationThe most important factor in the performance of the radio willbe the quality and positioning of the antenna. Most recordedproblems with VHF radios are related to poor antenna siting,faulty cabling, poor quality cable joints and low voltage sup-ply. Even a VHF as highly advanced as the RS87 cannot com-pensate for these factors. Therefore, if replacing an existingVHF installation, it is important that the antenna is thoroughlychecked for any faults or damage before use.As the range of VHF signals are governed by line of sight (seesection 8.3), the antenna should be placed as high as possible,while remaining clear of any metallic objects that could influ-ence the resonance of the antenna.The most popular antennae for marine use are 1m (3ft 3in)long. On sail boats these are usually mounted on the mast-head, where the length of the antenna keeps it clear from thenavigation lights and windvanes etc. This type of antenna canalso be mounted on the cockpit roof or garage of power boats.Longer whip antennae are recommended for larger boats -these radiate the same total power as smaller antennae, butconcentrate it into a narrower beam, which is advantageous ona tall mast at extreme range where concentrating the availablepower into a narrow horizontal beam becomes more impor-Fig 7.14 - Cable strain relief
tant. However, if the antenna is not vertical when transmitting,the beam will be angled either too high or too low (Fig 7.15) -Instruction Manual67Part No. E04297Fig 7.16 - Effect of heel on range of 1m marine antennaFig 7.15 - Effect of heel on range of longer whip antennaHere the wider beam of the shorter antenna will be more uni-versally effective, although the signal will be weaker (Fig 7.16) -Therefore vessels with a large heel angle (small sailboats)would be better choosing a short masthead antenna. Yourlocal agent should be able to provide specific advice on anten-na choice for the vessel it is to be fitted to.WARNING The antenna coaxial cable and any connectors used must be rated at 50Ω. Under no circumstances should standard domesticTV cable and connectors be used. Incorrectly rated cabling andconnectors could result in power not reaching the antenna, butalso power could be reflected back into the radio, damaging itin the process.The quality of any connections and integrity of the cable (with-out breaks in the sheathing) will directly affect the performanceof the radio. Poor soldering or corrosion of the terminals canimpair performance. We recommend that screw or crimp ter-minal type connectors are not used for any through deck fit-tings - a good quality waterproof solder terminal connector willbe less susceptible to poor connection due to corrosion of thecontacts.
To ensure the best performance of the radio, the antenna cableshould be routed where it is least likely to interfere with, orreceive interference from other electronic equipment, such asechosounder transducer cables and high current carryingcables.The antenna cable should terminate in a standard marinePL259 plug fitting. Connect the antenna plug to the socket onthe top of the transceiver unit and screw the retaining collardown (Fig 7.17) -RS87 VHF68 Part No. E04297NOTE To avoid possible water damage to the radio, it is recommend-ed that the antenna cable is looped to provide a drip path.7.4 Electrical interference suppressionInterference generated by the alternator of the engine mayoccasionally cause problems. The RS87 has been designed tominimise the effects of outside interference. However, precau-tions should still be taken - route the power supply and anten-na cables away from the engine compartment. The cable runshould not be down the same trunking as other cables carryinghigh current. The antenna cable should also be kept separatefrom the radio’s power cable.Engines with spark ignition - and also some refrigerators -should be fitted with suppressors. Your local agent should beable to give advice on this, and also supply suppression kitswhere necessary.Fig 7.17 - VHF antenna connection
8 APPENDIX8.1 Operating proceduresThe following operating procedure summary has been pro-posed by the UK Maritime and Coastguard Agency. It is notexhaustive and should not be regarded as a replacement forinformation provided by the proper two day VHF/DSC train-ing course required for all VHF license holders.8.1.1 Sending a distress alert1. Send a distress alert call (see section 2.7)2. Wait approx 15 seconds for a DSC acknowledgement fromthe Coastguard or a ship station.3. On receipt of a DSC acknowledgement or after about 15seconds, transmit the Distress call on channel 16 -“Mayday, Mayday, Mayday”“This is (name of vessel repeated three times)“Mayday”MMSI number and name of vessel or callsign, spoken oncePositionNature of distressIf the vessel is not in “grave and imminent danger”, an AllShips Urgency call followed by a spoken “Pan Pan” call or aroutine call to the nearest coastguard station may be moreappropriate. It is a prosecutable offense to initiate a DistressAlert call for any other reason than that the vessel and/or crewis in imminent danger.8.1.2 Acknowledging and relaying adistress alertWhen a DSC distress alert is received, an audible alarm willsound. Immediately cease any transmission that may interferewith distress traffic and continue a watch on channel 16.If there is no DSC acknowledgement from a coast station orship, after a short interval acknowledge by voice on channel 16 -“Mayday (MMSI of vessel in distress repeated three times)”“This is (name of own vessel, repeated three times)”“Received Mayday”(State the assistance you can give).Asimilar response should be given to a distress relay, using thewords “Mayday Relay” instead of “Mayday”.Instruction Manual69Part No. E04297
8.1.3 Cancelling a distress alertIf a DSC distress alert is sent accidentally, cancel it immediatelyon the RS87 by pressing the Cbutton to prevent repeats, thenmake the following announcement on channel 16 -“This is (name of vessel, callsign, MMSI)”“Cancel DSC Alert sent (date & time UTC)”Do not simply cancel the DSC alert without verbally cancellingit as well, otherwise the rescue authorities will not be awarethat this is a false alarm.8.1.4 Alerting all vessels within rangeIf the vessel is outside of coast radio range and needs to issue asafety warning to all vessels within radio range, transmit an AllShips Safety call by DSC. After about 15 seconds transmit onchannel 16 the safety call and message as follows -“Securité, Securité, Securit锓All stations (or called station)” repeated three times“This is (MMSI and name or callsign of own vessel)”Repeat text of safety message.8.1.5 Calling a coast radio stationEnter the MMSI of the station into the RS87, either manuallyor from the directory. When the call is acknowledged, theworking channel for voice communication will be indicatedand the RS87 will automatically switch to that channel. Make avoice call as normal.8.1.6 Making an intership callEnter the vessel’s MMSI into the RS87, either manually or fromthe directory. Before sending the call, enter the inter-ship chan-nel to be used for subsequent communication. When the alarmsounds on the called vessel, its operator should acknowledgeby DSC, then respond by voice on the selected channel.If the MMSI number of the vessel is not known, call as now onchannel 16. If no response is received, call on channel 13. Thisis the GMDSS bridge to bridge communication channel.8.2 NMEA sentences receivedThe following NMEA0183 sentences are processed by the RS87in order to transmit the boat’s position if a Distress Alert is ini-tiated -NMEA0183 version 2 and 3 - GGA, GLL, RMC, ZDARS87 VHF70 Part No. E04297
8.3 Transmission rangeBecause VHF signals travel in a straight line and are not reflect-ed back off the ionosphere as lower frequency signals are, therange of VHF signals is limited to ‘line of sight’, beyond whichthe other vessel passes behind the curve of the Earth.Therefore, the range will increase greatly the higher above sealevel the antenna is, as Fig 8.1 illustrates (assuming maximumtransmission power is used):Instruction Manual71Part No. E04297Therefore, the typical ship to ship range of a fixed VHF radiosuch as the RS87 with a masthead antenna will be approxi-mately 20 Km (12 miles). This will increase as height abovesea level increases, or if the other radio user’s antenna is at agreater height - note that the range between the yacht with theantenna mounted on a 9 M (30 Ft) mast and the shore stationincreases to 46-53 Km (29-33 Miles).Fig 8.1 - VHF transmission range
8.4 Frequency of channelsRS87 VHF72 Part No. E04297NOTE Ch 0 will only be made available in the UK to Coastguard users with written authorisation.Channel 70 is the designated Digital Selected Calling (DSC)channel and may not be used for voice transmissions.
8.5 Fault findingSymptom Possible Cause RemedyUnit will not switch on • Faulty connection to power • Check power connection• Fuse has blown • Replace fuse and checkpower supply current• Supply voltage above limit • Check supply voltage isless than 15.6vScan or Memory Scan is • Noise on the channel is • Increase squelch levellocking on a channel holding the scan • Inhibit channel from scanwithout a signal (see section 2.11.1)Dual Watch not being • Priority channel selected • Select a working channelentered • Handset off cradle • Replace handsetCannot change channel • Dual Watch (D/W) engaged • Exit Dual WatchCertain channels are • Some channels are restricted • Consult your nationalnot obtainable and not programmed depend- authority for permitteding on country of purchase channels in your regionWill not transmit • Scanning or D/W function active • Exit D/W or ScanWill not transmit on 25W • Low voltage when full transmit- • Check power supplybut OK on 1W ting current is drawn• Some channels are restricted to • Consult your nationallow power transmission only authorityTransmissions persistently • Damaged antenna • Replace antennaweak/display flashes • Antenna cable broken • Replace cableANT • Poor contact • Check antenna sockets &through deck connectorThese simple checks should be carried out before seeking tech-nical assistance and may save time and expense. Before con-tacting your servicing agent please obtain the radio’s serialnumber. The software iteration should also be quoted - this isshown in the large digits on the display for 2 seconds after theradio is turned on and should be written in the box below forfuture reference.Instruction Manual73Part No. E04297
8.6 Optional AccessoriesThe following accessories are available from your nearestSimrad Technical Dealer. Please quote the correct part numberwhen ordering.RS87 VHF74 Part No. E04297AHK87Active Handset Kit(includes 20m cable)LS80Loudspeaker LS81Intercom SpeakerPCK86:F or PCK86:HFixed control panel(Available with fistmike or telephone handset)
5.6 Technical specificationPower Supply . . . . . . . . . . . . . . . . . . . . . . . . 12v DC (10.8v - 15.5v DC)Channel Capability . . . . . . . . . . . . . . . . . . . . . 55 international channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-28, 60-88 simplex & semi-duplex . . . . . . . . . . . . . . . . . . . . . . . . UK : includes M (previously 37) and M2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USA : Wx1-10 receive only. . . . . . . . . . . . Scandinavia : leisure or fishing channels as appropriate. . . . . . . . . . . . . . . . . . . . . . . . . . . Canada : Canadian and USA channels.Private Channels . . . . . . . . . . . . . . . . . . . . . Up to 18 private channels*External Speaker Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Ω* Contact local Simrad Technical Dealer for further details of channel programming etc.TransmitFrequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155-163MhzPower Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 watt or 25 wattsCurrent Consumption . . . . . . . . . . . . . . . 5.5A (25 watts), 1.3A (1 watt)Harmonic and Spurious Emissions . . . . . . . . . . . . . . . . . . . . . < 0.25µWHum / Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < -40dBModulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±5kHzReceiveAudio Output Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 wattsCurrent Consumption . . . . . . . 600mA (Full Volume, illumination on) . . . . . . . . . . . . . . . . . . . . . . . 220mA (Fully Squelched, illumination off)Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . < 1µV emf for 20 dB SINADHarmonic and Spurious Emissions . . . . . . . . . . . . . . . . . . . . . . . < -2nWHum / Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < -40dBAdjacent Channel Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70dBIntermodulation Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70dBEnvironmentalTelephone Handset & Loudspeakers . . . . . . . . . . . . Waterproof to IP675.7 DimensionsInstruction Manual75Part No. E04297190mm (7.6in)70mm (2.8in) 45mm(1.8in)168mm (6.72in)243mm (9.72in)63mm(2.5in)110mm (4.4in)110mm (4.4in)48mm(1.9in)45mm(1.8in)
5.8 Declaration of ConformityRS87 VHF76 Part No. E04297English Hereby, Simrad Limited (Margate), declares that this RS87 VHF Radio is in compliance with the essential requirements and other relevant provisions ofDirective 1999/5/EC.Finnish Simrad Limited (Margate) vakuuttaa täten että RS87 VHF Radio tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivinmuiden ehtojen mukainen.Dutch Hierbij verklaart Simrad Limited (Margate) dat het toestel RS87 VHF Radio inovereenstemming is met de essentiële eisen en de andere relevante bepalingen vanrichtlijn 1999/5/EGFrench Par la présente, Simrad Limited (Margate) déclare que ce RS87 VHF Radio est conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CEqui lui sont applicablesSwedish Härmed intygar Simrad Limited (Margate) att denna RS87 VHF Radio står iöverensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelsersom framgår av direktiv 1999/5/EG.Danish Undertegnede Simrad Limited (Margate) erklærer herved, at følgende udstyr RS87 VHF Radio overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EFGerman Hiermit erklärt Simrad Limited (Margate), dass sich dieses RS87 VHF Radio inÜbereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi)Greek Με την παρουσα Simrad Limited (Margate) δηλωνει οτι RS87 VHF Radioσυµµορφωνεται προζ τιζ ουσιωδειζ απαιτησειζ και τιζ λοιπεζ σχετικεζ διαταξειζ τηζ οδηγιαζ 1999/5/ΕΚItalian Con la presente Simrad Limited (Margate) dichiara che questo RS87 VHF Radioè conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.Spanish Por medio de la presente Simrad Limited (Margate) declara que el RS87 VHF Radiocumple con los requisitos esenciales y cualesquiera otras disposicionesaplicables o exigibles de la Directiva 1999/5/CEPortuguese Simrad Limited (Margate) declara que este RS87 VHF Radio está conforme com os requisitos essenciais e outras provisões da Directiva 1999/5/CE.Website - www.simrad.com
5.9 Service & warrantyYour radio should seldom need servicing, although it will bene-fit from an application of silicone or Teflon grease to the anten-na and mic sockets each season. The equipment should be reg-ularly checked by making routine calls to other stations. On anannual basis, test the Distress Alert button by pressing it ONCE.This will display the Distress Alert screen and ensure that thebutton is functioning. Press On/C to return to the main screen -DO NOT HOLD DOWN THE DISTRESS BUTTON.The unit is guaranteed for 2 years from date of retail sale. If itis necessary to have the unit repaired, return it carriage prepaidto the agent in the country of purchase with a copy of thereceipted invoice showing the date of purchase. Where possi-ble, return all the components unless you are certain that youhave located the source of the fault. If the original box is notavailable, ensure that it is well cushioned in packing; therigours of freight handling can be very different from the loadsencountered in the marine environment for which the unit isdesigned.For Worldwide Warranty details, please refer to the WarrantyCard supplied with this unit.Instruction Manual77Part No. E04297
ALWAYS AT THE FOREFRONT OF TECHNOLOGYwww.simrad.com

Navigation menu