Simrad RS87 RS87 VHF Marine Radiotelephone with Class D DSC User Manual RS87 Manual

Download:
Mirror Download [FCC.gov]
Document ID	309255
Application ID	eDHr/mIuC+P0ysH/JVDjfg==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	286.77kB (3584656 bits)
Date Submitted	2003-03-12 00:00:00
Date Available	2003-04-28 00:00:00
Creation Date	2003-03-06 16:48:04
Producing Software	Acrobat Distiller 5.00 for Macintosh
Document Lastmod	2003-03-06 16:48:04
Document Title	RS87_Manual.qxd
Document Creator	QuarkXPressª: LaserWriter 8 Z1-8.7.1
Document Author:	martinl

A L W A Y S
A T
T H E
F O R E F R O N T
O F
T E C H N O L O G Y
Instruction Manual
Simrad RS87
VHF Radio System
III
RS87 VHF
© 2003 Simrad Ltd
The technical data, information and illustrations contained in this publication were to the best of our knowledge correct at the time of
going to print. We reserve the right to change specifications, equipment, installation and maintenance instructions without notice as
part of our policy of continuous development and improvement.
No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form, electronic or otherwise without
prior permission from Simrad Ltd.
No liability can be accepted for any inaccuracies or omissions in the publication, although every care has been taken to make it as complete and accurate as possible.
IV
Part No. E04297 Issue 1.1 05/03/03 MDL
Instruction Manual
CONTENTS
1. GENERAL
1.1
1.2
1.3
1.4
1.5
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
The Simrad integrated system . . . . . . . . . . . . . . . . . . . . . . . 9
Licensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Entering MMSI numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Group ID MMSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2. MAIN FUNCTIONS
2.1
2.2
2.3
General notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Switching on & Second Country mode . . . . . . . . . . . . . . . . 12
Changing channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.3.1 Channel Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.4 Volume adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.5 Squelch adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.6 Dual Watch mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.7 Tri-Watch mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.8 All Scan mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.8.1 Dynamic All Scan Inhibit . . . . . . . . . . . . . . . . . . . . . . 17
2.9 Memory Scan mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.9.1 Dynamic Memory Scan Delete . . . . . . . . . . . . . . . . . . 18
2.10 Adjusting backlighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.11 Handset off cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3. MENU MODE
3.1
3.2
3.3
Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.1.1 All Scan inhibit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.1.2 All Scan reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.1.3 All Scan show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.1.4 Memory Scan select . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.1.5 Memory Scan clear . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.1.6 Memory Scan show . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.1.7 Scan dwell time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.2.1 Ship’s MMSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.2.2 ATIS number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.2.3 Group MMSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
VHF items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.3.1 User channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.3.2 Position view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.3.3 Last used channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.3.4 Interrupt intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.3.5 Auxiliary audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.3.6 Speaker settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
RS87 VHF
CONTENTS ctd 4. DSC FUNCTIONS
4.1
4.2
4.3
4.4
4.5
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Making a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.2.1 Individual Routine call . . . . . . . . . . . . . . . . . . . . . . . . 31
4.2.2 Public Correspondence call . . . . . . . . . . . . . . . . . . . . . 32
4.2.3 All Ships Safety call . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.2.4 All Ships Urgency call . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.2.5 Group call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.2.6 Distress Alert call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Receiving a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.3.1 Individual Routine call . . . . . . . . . . . . . . . . . . . . . . . . 37
4.3.2 Public Correspondence call . . . . . . . . . . . . . . . . . . . . . 38
4.3.3 All Ships Safety call . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.3.4 All Ships Urgency call . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.3.5 Group call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.3.6 Distress Alert call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.3.7 Distress Alert acknowledgement . . . . . . . . . . . . . . . . 42
4.3.8 Distress Relay call . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Viewing the Call Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Position over 4 hours old . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
5. THE DIRECTORY
5.1
5.2
5.3
5.4
Switching between the directories . . . . . . . . . . . . . . . . . . . . 46
Viewing the directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Entering a number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Editing a number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6. MISCELLANEOUS FUNCTIONS
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
Selecting Weather Watch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
6.1.1 Weather Watch alert . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Security mode (voice scrambler) . . . . . . . . . . . . . . . . . . . . . 50
Editing Latitude, Longitude and UTC . . . . . . . . . . . . . . . . . 50
Toggling between Lat/Long and UTC views . . . . . . . . . . . 51
Intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
6.5.1 Making an intercom call . . . . . . . . . . . . . . . . . . . . . . . 52
6.5.2 Receiving an intercom call . . . . . . . . . . . . . . . . . . . . . 53
Loudhailer / Foghorn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
6.6.1 Loudhailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
6.6.2 Foghorn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
station speaker mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
iDSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Part No. E04297
Instruction Manual
CONTENTS ctd 7. INSTALLATION
7.1
7.2
7.3
7.4
Physical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
7.1.2 Transceiver installation . . . . . . . . . . . . . . . . . . . . . . . . 57
7.1.2 Handset installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
7.1.3 Station speaker installation . . . . . . . . . . . . . . . . . . . . . 59
Electronic installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
7.2.1 Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
7.2.2 Loudspeakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
7.2.3 Intercoms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
7.2.4 Loudhailer/Foghorns . . . . . . . . . . . . . . . . . . . . . . . . . 62
7.2.5 Remote foghorn button . . . . . . . . . . . . . . . . . . . . . . . . 62
7.2.6 Auxiliary audio input . . . . . . . . . . . . . . . . . . . . . . . . . 63
7.2.7 NMEA0183 input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
7.2.8 iDSC output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
7.2.9 Future options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
7.2.10 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
7.2.11 Cable strain relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Antenna installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Electrical interference suppression . . . . . . . . . . . . . . . . . . . . 68
8. APPENDIX
8.1
Operating procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
8.1.1 Sending a distress alert . . . . . . . . . . . . . . . . . . . . . . . . 69
8.1.2 Acknowledging and relaying a distress alert . . . . . . 69
8.1.3 Cancelling a distress alert . . . . . . . . . . . . . . . . . . . . . . 70
8.1.4 Alerting all vessels within range . . . . . . . . . . . . . . . . 70
8.1.5 Calling a coast station . . . . . . . . . . . . . . . . . . . . . . . . . 70
8.1.6 Making an intership call . . . . . . . . . . . . . . . . . . . . . . . 70
8.2 NMEA sentences received . . . . . . . . . . . . . . . . . . . . . . . . . . 70
8.3 Transmission range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
8.4 Frequency of channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
8.5 Fault finding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
8.6 Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
8.7 Technical specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
8.8 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
8.9 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . 76
8.10 Service & warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Part No. E04297
RS87 VHF
1 GENERAL
1.1 Introduction
16
INT
VOLUME
11
SQUELCH 07
LIFT
COVER
DISTRESS
TEL CALL
VOL
ON/C
The RS87 is a modular VHF radio and Class D Digital
Selective Calling (DSC) radio telephone system using a fully
featured telephone-style handset to access and control all functions. It supports the latest GMDSS requirements for nonSOLAS vessels from the International Maritime Organisation
(IMO). It will enable you to make digitally selected calls,
which are quicker and simpler to make than traditional voice
calls using Channel 16. Should a distress situation occur, with
the RS87 you can quickly raise an alert, indicating your identity, your position and automatically establish distress communication on the emergency voice channel.
DIR
The RS87 transceiver is robustly constructed using a pressure
die cast aluminium case for effective heat dissipation, ensuring
maximum transmission performance even after many hours
constant use.
VOL
SPEAKER
LAT/LON
Thank you for choosing Simrad
WX WATCH
CH SET
If you are pleased with your VHF we hope you will be interested in our range of marine electronic equipment, which is manufactured to the same high standards as the RS87. Please contact your nearest Simrad Agent for a catalogue showing our
increasing range of high tech navigational instruments, GPS,
autopilots, Radar, Echosounders, Chartplotters and VHF radio
Fig 1.1 - RS87 Handset
sets.
Simrad operate a policy of continual development and reserve
the right to alter and improve the specification of their products without notice.
Part No. E04297
Instruction Manual
1.2 The Simrad integrated system
The standard RS87 radiotelephone can support up to two stations with full intercom facility, geographical position input
via NMEA0183 and iDSC integration with Simrad chartplotters
which enables the plotters to display DSC call information.
With the addition of the expansion board, the system can support an additional two stations, two intercom speakers and forward and aft foghorn/loudhailer speakers in addition to the
standard functions.
Additional stations can either be another RS87 type telephone
handset, or an RS86 fixed panel display, with a passive telephone handset or fistmike allowing great flexibility in installations (Fig 1.2) -
BASIC SYSTEM
DUAL STATION SYSTEM
EXPANDED SYSTEM
Fig 1.2 - RS87 system options
Part No. E04297
RS87 VHF
1.3 Licensing
NOTE
Prior to use check the national licensing requirements for the
operator.
In the UK license applications and queries should be made to
the following authority Ship Radio Licensing
Radio Licensing Centre
The Post Office
PO Box 1495
Bristol
BS99 3QS
A set may only be operated by, or under the supervision of a
holder of a Certificate of Competence and Authority to
Operate. This involves a simple examination and an annual
license renewal fee. The VHF only certificate is administered
by the Royal Yachting Association Royal Yachting Association
RYA House
Romsey Road
Eastleigh
Hants, SO5 4YA
Holders of the Restricted Certificate of Competence in Radiotelephony (which covers MF/HF SSB etc), do not need a separate VHF certificate.
In all other countries, please contact your regional authority for
information.
10
Part No. E04297
Instruction Manual
1.4 Entering MMSI numbers
At the time of issue of your vessel’s radio license, an MMSI
(Maritime Mobile Service Identifier) must be requested. This is
a nine digit number which must be permanently entered into
the RS87 when the radio is first set up, otherwise the DSC
functions cannot be accessed.
NOTE
If the boat or the RS87 are subsequently sold, the radio must
be returned to an authorised Simrad agent for the MMSI number to be erased and the new owner’s MMSI number entered.
For European leisure vessels fitted with VHF DSC equipment, a
CEPT Short Range Certificate is required by the operator.
Additional requirements, such as GOC or ROC may apply to
operators on commercial vessels. Please enquire with your
local licensing authority for full details.
Refer to section 3.2.1 to enter the vessel’s MMSI number.
1.5 Group ID MMSI
For boats that are part of a flotilla, racing fleet or other group, a
Group ID MMSI number can also be entered which will allow
DSC communication within the group. Refer to section 3.2.3 to
enter a Group MMSI number.
Part No. E04297
11
RS87 VHF
2. MAIN FUNCTIONS
2.1 General notes
Although it has many advanced features, the RS87 has been
designed to be as simple and intuitive to operate as possible.
The Shift key is used to access the secondary functions printed
above each key - press and release Shift, then press the appropriate key. These secondary functions are shown in this manual in italics (eg Group).
NOTE
The Shift key will automatically time out of Shift Mode after
two seconds if another key is not pressed.
At any time, pressing ON/C will cancel the current operation.
The lowest occupied port is the master controller - therefore
any operations initiated on this handset will override all other
stations.
CAUTION
In order for other users to be able to operate the radio, it is
imperative that the handset is replaced in the cradle after use.
2.2 Switching on & Second Country mode
To turn the radio on, press the ON/C key. The display will
show the handset software issue number two seconds, then the
station number and software issue number for the transceiver
unit for two seconds.
As a default, the radio switches on tuned to the priority channel (normally 16). If Last Channel Used mode has been set (see
section 3.3.3) the radio will switch on tuned to the previously
used channel.
The radio stores the previous volume and squelch settings and
will use these on startup.
In countries where it is permitted, the RS87 can operate on a
secondary set of channels, such as the USA channels.
To select the secondary channel table, press Shift followed by
OK. The display will show the channel set selected for two
seconds before reverting to the default display.
NOTE
12
Channels available will depend on programming. Please
enquire with your national licensing authority for details of
permitted channel sets in your own country.
Part No. E04297
Instruction Manual
2.3 Changing channels
To select a channel, enter the channel number using the numeric keypad (Fig 2.1) -
INT
16
INT
VOLUME 05
SQUELCH 03
72
VOLUME 05
SQUELCH 03
Fig 2.1 - Selecting a channel
If the channel is invalid, the display will show “Invalid
Channel” and then revert to the previous channel.
The priority channel (normally 16) can be selected by pressing
16, which will also set the radio to 25W transmit power.
The preselected User Channel can be directly selected by pressing the User key. The display will show “U” next to the channel number to indicate that it is the User Channel (Fig 2.2).
INT
23
VOLUME 05
SQUELCH 03
Fig 2.2 - User channel selected
The default setting for the User Channel is 16. Refer to section
3.3.1 for details on setting the User Channel.
Part No. E04297
13
RS87 VHF
2.3.1 Channel Sets
In addition to the standard International Channel, the RS87 can
also be programmed with regional Auxiliary Channels, such as
the marina channels M and M2 in the UK, the USA weather
channels and the fishing or leisure channels in Scandinavia.
To display the channel sets available, press Shift followed by
1W (Ch Set). Multiple presses of the 1W key while still in Shift
Mode will scroll through the available channel sets.
INT
MAR I NAAAAA
MAR I NAAAAA
PR I VATE AAA
Fig 2.3 - Selecting auxiliary channel sets
(sets must be available to be displayed)
When the required channel set is displayed, enter the channel
number using the numeric keypad - eg “2” for M2 (Fig 2.4) -
INT
MAR I NAAAAA
Fig 2.4 - Selecting auxiliary channel number
The only exception to this is when selecting UK marina channel M, which has no number associated with it. Simply selecting the marina channel set will automatically select it.
NOTE
14
If no numeric keys are pressed within two seconds the radio
will revert to the previous working channel (except for marina
channel M as noted above).
Part No. E04297
Instruction Manual
2.4 Volume adjustment
To adjust the volume, press the VOL and VOL keys to
increase and decrease the setting respectively. Press and hold
the key to increase/decrease the setting rapidly.
The volume setting can be between 1 and 24 (loud).
2.5 Squelch adjustment
To adjust the squelch setting, press the SQ key to enter squelch
adjustment mode, then press the
and
(VOL) keys to
increase or decrease the squelch respectively. Press and hold
the key to increase/decrease the setting rapidly.
The squelch setting can be between 0 (open) and 10.
NOTE
Squelch mode will automatically time out after two seconds if
another key is not pressed. Squelch mode can also be cancelled
by pressing the ON/C key.
2.6 Dual Watch mode
Dual Watch allows the radio to scan between the selected
working channel and the watch channel (the priority channel normally 16).
To enter Dual Watch, select the required working channel, then
press Shift and 3 (DW) within two seconds.
If Dual Watch is selected while the handset is off cradle, the
display will show “Place back on cradle”. If the handset is
replaced within ten seconds of selecting Dual Watch, it will
automatically initiate Dual Watch when the handset is
replaced.
The display will show “D/W” - the large digits on the display
indicate the working channel, with the watch channel shown
below in small digits (Fig 2.5) DW
INT
D/WAAAAA 16
BBBBBBBBBB
Fig 2.5 - Dual Watch mode
Part No. E04297
15
RS87 VHF
If the radio detects a signal on the watch channel, it will lock
onto this and the large digits will change to show the watch
channel.
NOTE
All other stations will also show the Dual Watch display.
NOTE
Normal VHF functions will not be available when in Dual Watch
mode. To exit Dual Watch press 16, ON/C or lift the handset
from the cradle.
2.7 Tri Watch mode
Tri Watch allows the radio to scan between the selected working channel, the user channel and the watch channel.
NOTE
Tri Watch cannot be selected if the user channel is set to Ch16.
To enter Tri Watch, select the required working channel, press
Shift and then press and hold the 3 (DW) for two seconds.
Press & hold
If Tri Watch is selected while the handset is off cradle, the display will show “Place back on cradle”. If the handset is
replaced within ten seconds of selecting Tri Watch, it will automatically initiate Tri Watch when the handset is replaced.
The display will show “T/W” - the large digits on the display
indicate the working channel, with the user channel and watch
channel shown below in small digits (Fig 2.6) -
INT
10
T/WAAAAA 16
USERBBBBB6
Fig 2.6 - Tri Watch mode
If the radio detects a signal on the user or watch channels, it
will lock onto this and the large digits will change to show the
relevant channel.
NOTE
All other stations will also show the Tri Watch display.
NOTE
Normal VHF functions will not be available when in Tri Watch
mode. To exit Tri Watch press 16, ON/C or lift the handset
from the cradle.
16
Part No. E04297
Instruction Manual
2.8 All Scan mode
The scan function cycles the RS87 sequentially through each
enabled channel, pausing when a signal is detected.
Press Shift followed by 1 (Scan All) to enter All Scan Mode.
If Scan is selected while the handset is off cradle, the display
will show “Place back on cradle”. This function will be cancelled if the handset is not returned to the cradle within 10
seconds.
The display will show “Scan All” on the display. If the radio
detects a signal, it will lock onto this and the large digits will
change to show the relevant channel number (Fig 2.7) -
INT
67
SCAN
ALL
Fig 2.7 - All Scan mode
If the radio locks onto a busy channel, pressing OK will manually continue the scan. All Scan will otherwise automatically
restart when the channel becomes clear.
NOTE
All other stations will also show the All Scan display.
NOTE
While in scan mode, normal VHF functions are not available.
To exit All Scan press 16, ON/C or lift the handset from the
cradle.
2.8.1 Dynamic All Scan Inhibit
If the radio is constantly locking onto a busy channel when
scanning, this channel can be inhibited from the scan by pressing Shift then 1 while locked on that channel.
The display will show “Channel Inhibited” and the channel
will no longer be included in the scan cycle.
The channel can be reinstated using the menu option described
in section 3.1.1.
Part No. E04297
17
RS87 VHF
2.9 Memory Scan mode
Memory Scan gives the option of scanning a preprogrammed
set of channels specified by the user (see sections 3.1.4 and
3.1.5).
Press Shift then 2 (Scan M) to enter Memory scan mode.
If Memory Scan is selected while the handset is off cradle, the
display will show “Place back on cradle”. If the handset is
replaced within ten seconds of selecting Memory Scan, it will
automatically initiate Memory Scan when the handset is
replaced.
The display will show “Scan M” on the display. If the radio
detects a signal, it will lock onto this and the large digits will
change to show the relevant channel (Fig 2.8) -
INT
68
SCAN
Fig 2.8 - Memory Scan mode
If the radio locks onto a busy channel, pressing OK will manually continue the scan. Memory Scan will otherwise automatically restart when the channel becomes clear.
NOTE
If only one channel has been entered into the memory then
initiating Memory Scan will retune the RS87 to the stored
channel.
NOTE
All other stations will also show the Memory Scan display.
NOTE
While in memory Scan mode, normal VHF functions are not
available. To exit Memory Scan press 16, ON/C or lift the
handset from the cradle.
2.9.1 Dynamic Memory Scan Delete
If the radio is constantly locking onto a busy channel when
scanning, this channel can be removed from the Memory Scan
channel set by pressing Shift then 2 while locked on that
channel.
The display will show “Channel Deleted” and the channel will
no longer be included in the scan cycle.
18
Part No. E04297
Instruction Manual
2.10 Adjusting backlighting
The display and keypad are backlit - to set the backlighting
level press Shift followed by Call (Dimmer) to enter backlight mode.
Use the
and
(VOL) keys to adjust the backlighting level
from off through to level 5..
Press Ok or ON/C to exit the backlight mode at the selected
level.
NOTE
Backlighting levels will only affect this station.
2.11 Handset off cradle
When a handset is lifted off cradle, all other stations will show
“Occupied” on the display (Fig 2.9). This means that these stations are locked out until the handset is returned to the cradle,
unless the station is being called on intercom by the handset.
INT
16
STAT I ONAA2
OCCUP I EDBB
Fig 2.9 - Station 2 handset is in use
NOTE
Part No. E04297
The handset plugged into the lowest numbered port is
designated the Master unit. Lifting the Master handset will
override all other stations, even if it is displaying “Occupied” all other stations will then display “Occupied” and be locked
out.
19
RS87 VHF
3. MENU MODE
Menu mode is used to adjust the various settings of the radio,
such as channels inhibited from the scan functions, MMSI number programming and User channel selection.
To enter Menu mode, press Shift followed by 9 (Menu).
Use the the VOL and VOL
various menu options -
keys to scroll through the
- Scanning (section 3.1)
Options related to the various scanning functions such as
channel inhibit, memory scan select and scan dwell time.
- Numbers (section 3.2)
Entering of ID numbers such as MMSI, Group MMSI and
ATIS number (if applicable in country of use).
- VHF Items (section 3.3)
Miscellaneous options such as selection of User channel,
last used channel, interrupt intercom and speaker settings.
To select an option, press Ok.
To return to normal radio operation, press On/C.
NOTE
Entering Menu mode will inhibit the operation of the radio.
Exit Menu mode before returning the handset to the cradle to
permit normal operation.
3.1 Scanning
Once the Scanning menu option has been selected (see introduction to section 3), use the VOL and VOL keys to scroll
through the menu options All Scan inhibit (section 3.1.1)
All Scan reset (section 3.1.2)
All Scan show (section 3.1.3)
Memory Scan select (section 3.1.4)
Memory Scan clear (section 3.1.5)
Memory Scan show (section 3.1.6)
Scan dwell time (section 3.1.7)
To select an option, press Ok.
To return to the main menu, press On/C.
20
Part No. E04297
Instruction Manual
3.1.1
All Scan inhibit
If the radio is constantly locking onto a busy channel when
scanning, this channel can be inhibited from the scan cycle.
From the Scanning menu (see section 3.1) select All Scan Inhibit
and press Ok.
Enter the relevant channel number using the numeric keypad.
The display will show the channel number and it’s inhibit status
- “All Scan” for enabled, or “All Scan Inhibited” for inhibited
(Fig 3.1) -
INT
65
ALL SCANAA
I NH I B I TEDB
Fig 3.1 - Selected channel inhibited from scan
Press Ok to change the channel’s inhibit status - i.e if it is
enabled, pressing Ok will inhibit it and vice versa. If the channel is inhibited, it will no longer be included in the All Scan
cycle. Enabling the channel will re-include it.
Additional channels can be inhibited/enabled by entering the
channel number and repeating the above procedure.
To exit, press the VOL or VOL key to select another
Scanning menu option, or press On/C to return to the main
menu.
3.1.2
All Scan reset
This function will reset all inhibited channels so that they are
enabled.
From the scanning menu (section 3.1) select All Scan Reset and
press Ok - the display will show “Channels Reset” (Fig 3.2) -
CHANNELSSS
RESETEDBBB
Fig 3.2 - All inhibited channels reset
Press the VOL or VOL key to select another Scanning
menu option, or On/C to return to the main menu.
Part No. E04297
21
RS87 VHF
3.1.3
All Scan show
This function displays all the inhibited channels.
From the scanning menu (section 3.1) select All Scan Show and
press Ok. The display will then show “Showing Channels”
and display all the inhibited channels in sequence.
Press the VOL or VOL key to select another Scanning
menu option, or On/C to return to the main menu.
3.1.4
Memory Scan select
This function selects the channels to be used in the Memory
Scan cycle (see section 2.9).
From the scanning menu (section 3.1) select Memory Scan
Select and press Ok - the display will show “Mem Scan Select”.
Enter the relevant channel number using the numeric keypad.
The display will show the channel number and it’s memory status - “Mem Scan” if it is not currently selected for Memory
Scan, or “Mem Scan Enabled” if it is already selected (Fig 3.3) -
INT
65
INT
MEM SCANAA
CHANNEL CURRENTLY NOT SELECTED
65
MEM SCANAA
ENABLEDB B
CHANNEL ALREADY SELECTED
Fig 3.3 - Selecting channel for Memory Scan
Press Ok to change the channel’s Memory Scan status - i.e if it
is not selected, pressing Ok will add it to the Memory Scan
cycle and vice versa.
Additional channels can be added/removed by entering the
channel number and repeating the above procedure.
Press the VOL or VOL key to select another Scanning
menu option, or On/C to return to the main menu.
NOTE
22
North American users - Only one Weather channel can be
entered into Memory Scan - if another one is selected, it will
override the existing channel. The Weather channel is not
scanned as part of the Memory Scan sequence - it is used by
the Weather Watch function (see section 6.1).
Part No. E04297
Instruction Manual
3.1.5
Memory Scan clear
Memory Scan Clear will reset all channels selected for Memory
Scan so that they are disabled.
From the scanning menu (section 3.1) select Memory Scan
Clear and press Ok - the display will show “Channels Cleared”
(Fig 3.4) -
CHANNELSSS
CLEAREDBBB
Fig 3.4 - Selecting channel for Memory Scan
Press the VOL or VOL key to select another Scanning
menu option, or On/C to return to the main menu.
3.1.6
Memory Scan show
This function displays all channels selected for Memory Scan.
From the scanning menu (section 3.1) select Memory Scan
Show and press Ok. The display will then show “Showing
Channels” and display all the Memory Scan selected channels
in sequence.
Press the VOL or VOL key to select another Scanning
menu option, or On/C to return to the main menu.
3.1.7
Scan dwell time
This function is used to select the amount of time the RS87
remains on a channel after it has locked onto it during a scanning function (All Scan, Memory Scan) and the signal is lost.
From the scanning menu (section 3.1) select Scan Dwell Time
and press Ok - the display will show “Scan Dwell Time xx”,
where xx is the current dwell time in seconds (Fig 3.5) -
SCAN DWELL
T I ME
04
Fig 3.5 - Scan dwell time
The default time is 0, meaning that the scan will continue as
soon as the signal is lost. There are 11 levels from 0-10 seconds
- use the numeric keys to enter the scan dwell time and press
Ok to select - the display will show “Dwell Time xx Seconds”.
Press the VOL or VOL key to select another Scanning
menu option, or On/C to return to the main menu.
Part No. E04297
23
RS87 VHF
3.2 Numbers
The Numbers menu is used for entering ID numbers such as
MMSI, Group MMSI and ATIS (if applicable in country of use).
Once the Numbers menu option has been selected (see introduction to section 3), use the VOL and VOL keys to scroll
through the menu options Ship’s MMSI (section 3.2.1)
ATIS Number (section 3.2.2)
Group MMSI (section 3.2.3)
NOTE
The ATIS Number option will only be shown if the radio is
ATIS enabled. This feature is only available for sets used in
Benelux and the Rhine/Danube waterways.
To select an option, press Ok.
To return to the main menu, press On/C.
3.2.1
Ship’s MMSI
Ship’s MMSI will display the boat’s MMSI number if it has
already been entered, or will allow the MMSI to be entered if
the radio is being used for the first time.
From the Numbers menu (section 3.2) select Ship’s MMSI and
press Ok - the display will show “Ships MMSI” and the MMSI
number (unless the number has not been entered yet, in which
case it will show “_ _ _ _ _ _ _ _ _” - Fig 3.6).
INT
16
SH I PS MMS Ii
-----------Fig 3.6 - Entering MMSI Number
CAUTION
24
The MMSI number can only be entered once and cannot be
edited by the user. If it is necessary to change the MMSI (for
example if the radio is being moved to another boat), the radio
must be sent to an authorised Simrad service agent for reprogramming.
Part No. E04297
Instruction Manual
To enter the MMSI number press Ok again. The display will
show ENTER MMSI and the first dash in the number will start
flashing to indicate that entry can begin.
Enter the nine digit MMSI number using the numeric keypad
and press Ok. The radio will then ask that the MMSI is reentered to confirm. If the two numbers do not match, the
MMSI will need to be re-entered and re-confirmed.
Use the Call and MSG keys to move the cursor to correct
any errors. The cursor position is indicated by the number flashing. Enter a new number to overwrite the incorrect number.
NOTE
The MMSI number will not be accepted unless all 9 characters
have been entered.
Press the VOL or VOL key to select another Numbers
menu option, or On/C to return to the main menu.
3.2.2
NOTE
ATIS number
This section applies only to radios used in countries where the
ATIS system is in operation (Benelux and the Rhine/Danube
waterways). This option will only appear on ATIS equipped
radios.
From the Numbers menu (section 3.2) select ATIS No. - the
display will show “ATIS No.” and the ATIS number (unless
the number has not been entered yet, in which case it will
show “_ _ _ _ _ _ _ _ _”).
CAUTION
The ATIS number can only be entered once and cannot be
edited by the user. If it is necessary to change the ATIS number, the radio must be sent to an authorised Simrad service
agent for reprogramming.
To enter the ATIS number press Ok again. The display will
show ENTER ATIS and the first dash in the number will start
flashing to indicate that entry can begin.
Enter the nine digit ATIS number using the numeric keypad
and press Ok. The radio will then ask that the number is reentered to confirm. If the two numbers do not match, the number will need to be re-entered and re-confirmed.
Use the Call and MSG keys to move the cursor to correct
any errors. The cursor position is indicated by the number flashing. Enter a new number to overwrite the incorrect number.
NOTE
Part No. E04297
The ATIS number will not be accepted unless all 9 digits have
been entered - the prefix 9 is automatically inserted by the radio.
25
RS87 VHF
Press the VOL or VOL key to select another Numbers
menu option, or On/C to return to the main menu.
3.2.3
Group MMSI
For boats that are part of a flotilla, racing/fishing fleet or other
group, a Group ID MMSI number can also be entered and used
to contact other boats in the same fleet.
NOTE
The Group MMSI number may be allocated on a temporary
basis by the local administration, for this reason the number
can be changed by the user.
From the Numbers menu (section 3.2) select Group MMSI - the
display will show “Group MMSI” and the Group MMSI number (unless the number has not been entered yet, in which case
it will show “0 _ _ _ _ _ _ _ _”).
To enter the Group MMSI number press Ok again. The display
will show ENTER MMSI and the first dash in the number will
start flashing to indicate that entry can begin.
The first digit of a Group MMSI is always 0, and this is preselected by the radio. Enter the remaining 8 digits using the
numeric keypad and press Ok (Fig 3.7) -
INT
16
GROUP MMS II
0436 1 - - - Fig 3.7 - Entering Group MMSI number
Use the Call and MSG keys to move the cursor to correct
any errors. The cursor position is indicated by the number
flashing. Enter a new number to overwrite the incorrect
number.
NOTE
The number will not be accepted unless all 8 remaining digits
have been entered.
Press the VOL or VOL key to select another Numbers
menu option, or On/C to return to the main menu.
26
Part No. E04297
Instruction Manual
3.3 VHF items
The VHF items menu contains the settings for miscellaneous
items such as user channel, position view, auxiliary audio and
speaker settings amongst others.
Once the VHF items menu option has been selected (see introduction to section 3), use the VOL and VOL keys to scroll
through the menu options User channel (section 3.3.1)
Position view (section 3.3.2)
Last used channel (section 3.3.3)
Interrupt intercom (section 3.3.4)
Auxiliary audio (section 3.3.5)
Speaker settings (section 3.3.6)
Scrambler codes (only if scrambler option is fitted)
Serial number
To select an option, press Ok.
To return to the main menu, press On/C.
3.3.1
User channel
This is a user programmable priority channel that is used in the
Tri-watch function and is selected by pressing the User key.
From the VHF items menu (section 3.2) select User Channel
and press Ok - the display will show “User Channel”.
Enter the channel number using the numeric keypad and press
Ok. The display will show “Set User Channel” (Fig 3.8) -
INT
10
SET USERAA
CHANNELBBB
Fig 3.8 - Setting the User Channel
Press the VOL or VOL key to select another VHF items
menu option, or On/C to return to the main menu.
Part No. E04297
27
RS87 VHF
3.3.2
Position view
This option allows the user to view the current GPS position that
will be used if a distress call is made (Fig 3.9). The function of
this option depends on whether the position is being received
automatically via NMEA, or if it has been entered manually.
INT
LAT
LON
16
89º 23. 000N
102º 54. 120E
Fig 3.9 - Position display
From the VHF items menu (section 3.2) select Position View and
press Ok.
If GPS position information is being received, the display will
show “Position View Off”. Press the Ok key to toggle between
ON and OFF. When this option is turned on, the bottom two
lines of the display will show the current Lat / Long position on
all handsets. If the volume or squelch is adjusted, the display
will show the settings while the up/down keys are operated,
before reverting to the position display.
If no GPS position information is being received, the display
will show “View”. Pressing Ok will show the manual position
entered, or the last known GPS position. If there has not been a
position entered, the Lat and Long display will show all 9’s.
Press the VOL or VOL key to toggle between position and
time (UTC) displays.
Press On/C to exit.
3.3.3
Last used channel
Normally the RS87 will power up on the programmed start up
channel (usually the priority channel). This function enables the
radio to power up on the last used channel - the default setting is off.
From the VHF items menu (section 3.2) select Last Used Chan
and press Ok - the current status will be shown - “On” or “Off”.
Press Ok to toggle between the On and Off settings.
Press the VOL or VOL key to select another VHF items
menu option, or On/C to return to the main menu.
28
Part No. E04297
Instruction Manual
3.3.4
Interrupt intercom
This function is used to specify whether intercom or loudhailer
functions should be interrupted when an incoming VHF transmission is received - the default setting is “Yes”.
From the VHF items menu (section 3.2) select Interrupt
Intercom and press Ok - the display will show “Interrupt
Intercom” and the current status - “Y” or “N”.
Press Ok to toggle between Yes and No interrupt.
Press the VOL or VOL key to select another VHF items
menu option, or On/C to return to the main menu.
3.3.5
Auxiliary audio
The Auxiliary Audio input allows an outside audio source to
be connected to the radio and outputted through the speaker/
intercom system (eg an FM receiver for weather forecasts etc).
From the VHF items menu (section 3.2) select Auxiliary Audio
and press Ok to enter the Auxiliary Audio sub-menu.
Press the VOL or VOL keys to select the required
Auxiliary Audio settings option Use Aux AF
Interrupt Aux AF
To turn the Auxiliary Audio input on, select “Use Aux AF” the display will show “Use Aux AF” and the current status
(“No” or “Yes”). Press Ok to toggle between the On and Off
settings. If the Aux AF option is switched on, the external
audio source will be outputted through all speakers in the system at the set volume level.
NOTE
When this option is turned on, the display will show “Using
Aux Audio” on the bottom line of the display. If the volume or
squelch is adjusted, the volume/squelch settings will be shown
while they are being adjusted, then revert to this display.
To specify whether the Auxiliary Audio input should be interrupted if an incoming VHF transmission is received select
“Interrupt Aux AF” using the VOL or VOL key - the
default setting is “Yes”.
Press Ok to toggle between Yes and No interrupt.
Press the VOL or VOL key to select another Auxiliary
Audio sub-menu option, or On/C to return to the VHF Items
menu. Press On/C again to return to the main menu.
Part No. E04297
29
RS87 VHF
3.3.6
Speaker settings
The Speaker Settings option is used to set the individual
default volume levels for each station, intercom and loudhailer
in the system.
From the VHF items menu (section 3.2) select Speaker Settings
and press Ok to enter the Speaker Settings sub-menu. Press
the VOL or VOL keys to scroll through each speaker, displaying the default volume level for each one.
NOTE
Only connected speakers will be shown.
The first option in the sub-menu is Reset To Defaults (Fig 3.10) pressing Ok when this option is displayed will reset all speaker
levels to their default settings - the display will show “Resetting
Levels”.
INT
16
RESET TO000
DEFAULTS00
Fig 3.10 - Resetting speaker settings to defaults
To set the required volume levels for each individual position,
use the VOL or VOL keys to select the required station
and press Ok. The selected speaker will then emit a continuous tone indicating the current volume level. Press VOL or
VOL to adjust the volume level as suitable and press Ok to
confirm.
Press the VOL or VOL keys to select another station and
repeat the above procedure, or On/C to return to the VHF
Items menu. Press On/C again to return to the main menu.
30
Part No. E04297
Instruction Manual
4. DSC FUNCTIONS
4.1 General
The RS87 features full Class D DSC (Digital Selective Calling)
functionality, which enables the user to make digitally selected
calls - quicker and simpler to make than traditional voice calls
using Channel 16. Should a distress situation occur, a Distress
Alert call can be initiated, indicating the vessel’s identity, position and automatically establish distress communication on the
emergency voice channel (normally Channel 16)
NOTE
DSC functions will only be available if the MMSI number has
been entered into the radio (see section 3.2.1).
4.2 Making a call
4.2.1
Individual Routine call
Press the Call
tion.
key to enter the Individual Routine call func-
Either manually enter the MMSI number of the station using
the numeric keypad, or press the VOL and VOL keys to
scroll through the MMSI number directory (Fig 4.1). Press Ok
to confirm the selected entry.
INT
06
SEA M I STAA
ON CH 06 00
Fig 4.1 - Selecting a number from the MMSI directory
Enter the required working channel using the numeric keypad,
or use the VOL or VOL keys to scroll through the four
default reply channels (06, 08, 72 & 77). Press Ok to confirm.
NOTE
Only simplex channels can be selected as the working channel.
NOTE
If the MMSI entered is for a coast station, the option to select a
working channel will not be available - this is specified by the
coast station, and will normally be a duplex channel.
The display will show “Press Ok To Send” - press Ok to initiate the call, or On/C to abort.
Part No. E04297
31
RS87 VHF
On initiation of the call, the display will show “Awaiting
Acknowledg” (Fig 4.2). Once an acknowledgement is received,
the radio will automatically.switch to the specified working
channel.
INT
06
AWA I T I NGAA
ACKNOWLEDG
Fig 4.2 - Call sent, awaiting acknowledgment from recipient
NOTE
If an acknowledgement is not received, the radio will continue
showing the “Awaiting Acknowledg” display for 4.5 minutes
before timing out and returning to normal operation.
4.2.2
Public Correspondence call
For vessels within range of a country operating the necessary
network, the RS87 can be used to directly make and receive
Public Correspondence calls from a land based telephone system via a coast station.
Press Shift then On/C to enter the Public Correspondence call
function.
Either manually enter the telephone number using the numeric
keypad (Fig 4.3), or press the VOL and VOL keys to scroll
through the telephone number directory. Press Ok to confirm
the selected entry.
INT
06
44 1 606547
677-----Fig 4.3 - Dialling a number manually
NOTE
32
Check with your local network provider for usage instructions.
Part No. E04297
Instruction Manual
The next stage is to specify the coast station the call is to be
routed through. Either manually enter the MMSI number of the
coast station using the numeric keypad, or press the VOL and
VOL keys to scroll through the Coast Station MMSI number
directory (Fig 4.4). Press Ok to confirm the selected entry.
INT
06
COAST 1 AAA
Fig 4.4 - Selecting a Coast Station from the coast station directory
NOTE
The MMSI number entered must have two leading zeros
(indicating a coast station), or it will not be accepted.
The display will show “Press Ok To Send” - press Ok to initiate the call, or On/C to abort.
On initiation of the call, the display will show “Attempting To
Connect”. If the call cannot be connected for any reason, the
display will show “Cannot Connect”, then “Pls Wait 15
Minutes” before returning to the default display.
If the call is connected, the display will show “Call In
Progress” (Fig 4.5) - press the PTT key to talk and release to
listen.
INT
07
CALL I N AAA
PROGRESSBB
Fig 4.5 - Call has been connected
NOTE
The channel number displayed during the call is determined
by the Coast Station.
Press On/C to end the call, or wait for the other end to replace
the receiver.
Part No. E04297
33
RS87 VHF
4.2.3
All Ships Safety call
To make an All Ships Safety call, lift the protective cover on the
front of the handset and press the Safety key. The display will
show “Safety on Ch 16” (Fig 4.6) -
INT
06
SAFE T YAAAA
ON CH 16 00
Fig 4.6 - Making an All Ships Safety call
Enter the required working channel using the numeric keypad,
or use the VOL or VOL keys to scroll through the four
default reply channels (06, 08, 72 & 77). Press Ok to confirm.
NOTE
Only simplex channels can be selected as the working channel.
The display will show “Press Ok To Send” - press Ok to initiate the call, or On/C to abort.
4.2.4
All Ships Urgency call
To make an All Ships Urgency call, lift the protective cover on
the front of the handset and press the Urgency key. The display will show “Urgency on Ch 16” (Fig 4.7) -
INT
06
URGEN CYAAA
ON CH 16 00
Fig 4.6 - Making an All Ships Urgency call
NOTE
As All Ships Urgency calls must use Ch 16 for voice communication, the option to manually select a working channel is not
available.
The display will show “Press Ok To Send” - press Ok to initiate the call, or On/C to abort.
34
Part No. E04297
Instruction Manual
4.2.5
Group call
Press the Shift key twice to enter the Group call function - the
display will show the Group MMSI number stored in the radio
(see section 3.2.3).
Enter the required working channel using the numeric keypad,
or use the VOL or VOL keys to scroll through the four
default reply channels (06, 08, 72 & 77). Press Ok to confirm
(Fig 4.7) -
INT
06
026530 1 45
ON CH 06B
Fig 4.7 - Making a Group Call
NOTE
Only simplex channels can be selected as the working channel.
The display will show “Press Ok To Send” - press Ok to initiate the call, or On/C to abort.
4.2.6
WARNING
Distress Alert call
This call should only be made if the vessel is in a genuine
distress situation. It is an offense to send a Distress Alert call
if the vessel or crew are not in danger.
The distress button is located under the protective cover on the
front of the handset. Press the Distress button to access the
Distress Alert call function - the display will show “Distress
Undefined” (Fig 4.8) -
INT
--
D I STRESSA A
UNDEF I NED b
Fig 4.8 - Distress Alert menu
ctd -
Part No. E04297
35
RS87 VHF
Use the VOL or VOL keys to scroll through the available
Nature of Distress categories • Undefined (default)
• Abandoning
• Piracy
• MOB
• Fire
• Flooding
• Collision
• Grounding
• Listing
• Sinking
• Adrift
Press and HOLD the Distress key to begin the 5 second countdown - the large digits will count down from 5 to 1 before initiating the distress alert - the display will show “Sending Alert”
(Fig 4.9) -
INT
--
SEND I NGAAA
ALER T BBBBB
Fig 4.9 - Sending a Distress Alert
NOTE
The Distress Alert call can be aborted if the Distress key is
released at any time before the 5 second countdown has ended.
Press On/C to return to normal radio operation.
The Distress Alert call sent includes the vessel’s MMSI, the
nature of the distress as specified, the time the call was sent
and the current position of the vessel (if the appropriate navigational receiver is connected to the radio, or a manual position has been entered - see section 6.3).
The radio will switch to monitoring channel 16 and the display
will show “Awaiting Acknowledg” until an acknowledgement
is received. The radio will automatically repeat the Alert
approximately every four minutes until either an acknowledgement is received, or On/C is pressed (it is not recommended that the Distress Alert is cancelled manually by pressing
On/C unless you are requested to do so by the rescue authorities).
36
Part No. E04297
Instruction Manual
When an acknowledgement is received from the Rescue Coordination Centre, this will automatically cancel the Distress
Alert transmission. The subsequent rescue co-ordination will
be performed using the voice working channel (Ch 16).
WARNING
If a DSC distress alert is sent accidentally, cancel it immediately
on the RD87 by pressing the On/C button to prevent repeats,
then make the following announcement on channel 16 “This is (name of vessel, callsign, MMSI)”
“Cancel DSC Alert sent (date & time UTC)”
Do not simply cancel the DSC alert without verbally cancelling
it as well, otherwise the rescue authorities will not be aware
that this is a false alarm.
4.3 Receiving a call
4.3.1
Individual Routine call
If an Individual Routine call is received, the radio will sound
an incoming call alarm.
The display will flash between displaying “Call From”, the
caller’s MMSI and the specified working channel (Fig 4.10). If
the caller’s MMSI is stored in the MMSI directory (see section
5.2), then the display will show the name stored instead of the
MMSI number.
INT
10
CALL FROMA
3453428599
REPLY ONA0
CH 0628599
Fig 4.10 - Receiving incoming Individual Routine call
Press Ok to accept the call or On/C to reject the call.
If the call has been accepted, the display will show “Send
Acknowledg”. Press Ok to send a call acknowledgement and
automatically switch to the specified working channel.
Part No. E04297
37
RS87 VHF
4.3.2
Public Correspondence call
A Public Correspondence call is a call made from a landbased
telephone which is routed via a coast station. This is only
available in countries operating the necessary network.
NOTE
At present, it is not possible to receive incoming calls on the
Public Correspondence network - calls can only be made
from the radio. This section is for reference purposes only.
When a Public Correspondence call is received the radio will
sound an incoming call alarm.
The display will flash between displaying “Tel Call From” and
the caller’s telephone number. If the caller’s number is stored
in the Telephone Number directory (see section 5.3), then the
display will show the name stored instead of the telephone
number (Fig 4.11) -
INT
10
TEL CALLA 0
FROM428599
SIMRAD ONA0
8599
Fig 4.11 - Receiving incoming Public Correspondence call
Press Ok to accept the call or On/C to reject the call - the display will show “Call In Progress”.
NOTE
As the telephone call is transmitted via a VHF channel
specified by the coast station, it will still be necessary to press
the PTT key to talk and release it to listen, as with a normal
VHF call. The coast station will disconnect the call if the PTT
is not pressed for 5 seconds at least every 45 seconds.
To end the call, press the On/C key, or wait until the caller
replaces the receiver (an End Call signal will be sent to the
radio). Replace the handset in the cradle.
38
Part No. E04297
Instruction Manual
4.3.3
All Ships Safety call
If an All Ships Safety call is received, the radio will sound an
incoming call alarm.
The display will flash between displaying “All Ships Safety”
and the caller’s MMSI. If the caller’s MMSI is stored in the
MMSI directory (see section 5.2), then the display will show the
name stored instead of the MMSI number.
Press Ok to accept the call - the display will change to “Reply
On Ch X”, where X is the specified working channel, or On/C
to reject the call.
Press Ok again to automatically switch to the working channel.
4.3.4
All Ships Urgency call
If an All Ships Urgency call is received, the radio will sound an
incoming call alarm.
The display will flash between displaying “All Ships Urgency”
and the caller’s MMSI. If the caller’s MMSI is stored in the
MMSI directory (see section 5.2), then the display will show the
name stored instead of the MMSI number (Fig 4.12) -
INT
10
ALL SHIPSSS
URGENCY9 9
FROMPRAY 0
SEASPRAY 0
Fig 4.12 - Incoming All Ships Urgency call
Press Ok to accept the call and automatically switch to channel
16, or On/C to reject the call.
NOTE
Part No. E04297
All Ships Urgency calls always use channel 16 as the working
channel.
39
RS87 VHF
4.3.5
Group call
If the radio has a Group MMSI number entered (see section
3.2.3) and a Group call is received, the radio will sound an
incoming call alarm.
The display will flash between displaying “Routine Group
Call” + the caller’s MMSI and the specified working channel
(Fig 4.13). If the caller’s MMSI is stored in the MMSI directory
(see section 5.2), then the display will show the name stored
instead of the MMSI number.
INT
06
ROUT I NES S
GROUP CALL
FROMPRAY 0
3895623970
Fig 4.13 - Incoming Group call
Press Ok to accept the call - the display will change to “Reply
On Ch X” (Fig 4.14), where X is the specified working channel,
or On/C to reject the call.
INT
06
REPLY ONAA
CH 1 0BBBBB
Fig 4.14 - Working channel specified by incoming Group call
Press Ok again to automatically switch to the working
channel.
40
Part No. E04297
Instruction Manual
4.3.6
Distress Alert call
If a Distress Alert call is received, the radio will sound an
incoming call alarm.
The display will flash between displaying “Distress Alert” and
the caller’s MMSI along with the nature of the distress alert.
If the caller’s MMSI is stored in the MMSI directory (see section
5.2), then the display will show the name stored instead of the
MMSI number (Fig 4.15) -
INT
06
D I STRESS S
ALERT CALL
S I NK I NG 0
3453428599
Fig 4.15 - Incoming Distress Alert call
Press Ok to accept the call and automatically switch to channel
16, or On/C to reject the call.
The full details of the Distress Alert may be viewed in the log
(see section 4.4).
NOTE
Part No. E04297
Distress Alert calls always use channel 16 as the working
channel.
41
RS87 VHF
4.3.7
Distress Alert acknowledgement
If an acknowledgement is received for a Distress Alert sent
(normally from a coast station or rescue co-ordination centre),
the radio will sound an incoming call alarm.
The display will flash between displaying “Distress
Acknowledg” and the MMSI of the vessel in distress, or your
MMSI if the Distress Alert was sent by the RS87 and the
Distress Alert transmission sent has been cancelled.
If the vessel’s MMSI is stored in the MMSI directory (see section 5.2), then the display will show the name stored instead of
the MMSI number (Fig 4.16) -
INT
06
D I STRESS S
ACKNOWLEDG
FORK I NG 0
ROBERTA0 0
Fig 4.16 - Distress Acknowledgment received
NOTE
The MMSI / name displayed will be that of the vessel in
distress, not the station that has acknowledged the call.
Press Ok to accept the acknowledgment and automatically
switch to channel 16, or On/C to ignore the call.
NOTE
42
Distress Alert calls always use channel 16 as the working
channel.
Part No. E04297
Instruction Manual
4.3.8
Distress Relay call
The Distress Relay facility enables an incoming Distress Alert
call to be passed onwards via boats within receiving distance of
the call, thus increasing the potential range of the Distress Alert
call.
If a Distress Relay call is received, the radio will sound an
incoming call alarm.
The display will flash between displaying “Distress Relay”
and the vessel’s MMSI (Fig 4.17) -
INT
06
D I STRESS S
RELAY A L L
FOR I N G 0
3453428599
Fig 4.17 - Incoming Distress Relay
If the vessel’s MMSI is stored in the MMSI directory (see section 5.2), then the display will show the name stored instead of
the MMSI number.
NOTE
The MMSI / name displayed will be that of the vessel in
distress, not the vessel that relayed the call.
Press Ok to accept the call, automatically switch to channel 16
or On/C to reject the call.
Part No. E04297
43
RS87 VHF
4.4 Viewing the Call Log
The call log records details of the last 20 DSC or telephone calls
received including the date and time received, the type of call
and the caller id. There are two separate logs - one for “standard” calls, the other for distress calls.
NOTE
All calls are logged, even those rejected by pressing On/C.
Press MSG enter the Call Log menu. If the call logs are
empty the display will show “No Calls Received” before
returning to the default display.
Press the Call and MSG keys to switch between the standard call log (indicated by “1” shown next to the large digits)
and the distress call log (indicated by “2” shown next to the
large digits).
Press VOL or VOL to scroll through the log entries - the display will show the call type and the date/time the call was
received (Fig 4.18). The small digit shows the log type (1 - standard call log, 2 - distress call log) and the large digits show the
entry number - the first entry shown is the most recent call.
INT
MSG
03
I ND I V I DUAL
1 9- 1 2 1 452
Fig 4.18 - Viewing Call Log entry
NOTE
The date and time displayed uses the date/time data received
from the navigational receiver interfaced to the radio, not from
the incoming message. If a navigational receiver was not connected to the radio at the time the message is received the date
and time will not be displayed.
Press Ok to view the details of the selected call - the display
will show the caller’s number (Or the name if the number is
stored in the directory).
44
Part No. E04297
Instruction Manual
Press VOL or VOL to display any relevant additional
information - for example the nature of distress and position of
the vessel in distress if viewing the distress call log (Fig 4.19) -
INT
MSG
07
D I ST ALERT
1 4- 1 0 0937
S I NK I NG 0
3453428599
LA 56-52N
LO 009-50E
Fig 4.18 - Viewing Call Log entry
Press On/C to return to the log entries menu. Press On/C
again to exit the Call Log menu.
4.5 Position over 4 hours old
Normally current position data is supplied automatically to
the radio via an interfaced navigational receiver (see section
7.2.7) or by manually entering a position (see section 6.3). If
the last recorded position is over 4 hours old, the display will
show “Position 4 Hours Old”. Press Ok to confirm and manually enter a position (refer to section 6.3) or On/C to ignore
the message.
NOTE
Part No. E04297
This display will be shown 30 minutes after switch on if there
is no NMEA position data being received, or the position has
not been manually entered.
45
RS87 VHF
5. THE DIRECTORY
The Directory function allows frequently used boat MMSI,
Coast Station MMSI and telephone numbers to be stored in the
radio. To enter the directory, press Shift then MSG (Dir).
5.1 Switching between the directories
The large digits will show the currently displayed entry number and the smaller digit to the left of the large digits will show
the currently selected directory 1. Boat MMSI directory
2. Telephone number directory
3. Coast Station MMSI directory
Press Call
and MSG
to switch between the directories.
5.2 Viewing the directory
Select the appropriate directory using the Call and MSG
keys. Use the VOL or VOL keys to scroll through the
directory entries (Fig 5.1) -
INT
DIR
01
SEASPRAY 0
475394270
INT
DIR
02
ROBERTAY 0
9463872 1 5
Fig 5.1 - Scrolling through the directory entries
46
Part No. E04297
Instruction Manual
5.3 Entering a number
Press Ok to begin entering a new number - the large digits will
show the entry number in the directory (1 if it is the first entry).
Enter the name first - use the VOL or VOL keys to scroll
through the alphabetical characters and the numeric keypad to
enter any numbers (Fig 5.2)
Press MSG to move the cursor forward, or Call to move
back and correct any errors (The cursor position is indicated by
the character flashing - enter a new character to overwrite).
Press Ok to confirm the entry and move on to the MMSI entry.
INT
DIR
01
SEASP- - - - ---------Fig 5.2 - Entering a new name into the directory
Use the numeric keypad to enter the number (Fig 5.3). Press the
Call and MSG keys to move the cursor to correct any errors.
The cursor position is indicated by the number flashing - enter a
new number to overwrite the incorrect number.
INT
DIR
01
SEASPRAY 0
47539----Fig 5.3 - Entering the number
Press Ok to confirm and store the entry to the directory.
Press On/C at any time to abort to the default display.
NOTE
Part No. E04297
If using the Boat or Coast Station directories the entry will not
be accepted unless all nine digits of the MMSI number have
been entered.
47
RS87 VHF
5.4 Editing a number
Select the directory entry to be edited and press Ok. Use the
VOL or VOL keys to highlight either the name or the
number for editing - the selected field will flash. Press Ok
again to begin editing the selected field.
Use the Call and MSG keys to move the cursor - the cursor
position is indicated by the character flashing. Enter a new character to overwrite - use the numeric keypad to enter a number,
or press VOL or VOL to scroll through the alphabetical
characters (Fig 5.4) -
INT
DIR
01
SEASPRAY 0
475394270
INT
DIR
Selected
field will
flash
01
SEASP- - - - 475394270
Fig 5.4 - Editing an existing directory entry
Press Ok to confirm and store the edited entry or On/C to
abort entry.
48
Part No. E04297
Instruction Manual
6. MISCELLANEOUS FUNCTIONS
6.1 Selecting Weather Watch
The Weather Watch function enables the radio to monitor a single Weather channel specified in the Memory Scan Select function (see section 3.1.4). A transmission on a Weather channel is
preceded by a tone - if this is detected by the radio, it will sound
an alert allowing the user to switch to the Weather channel.
To enable Weather Watch, press Shift followed by the User key
(Wx Watch). The“WX” legend will be shown in the top left of
the display and the selected weather channel will be shown on
the bottom line of the display (Fig 6.1) WX
12
WEATHERAAA
WATCHBBBW4
Fig 6.1 - Selecting Weather Watch mode
NOTE
If a Weather channel has not been specified, the display will
show “No Wx Chan Selected” and Weather Watch will not be
enabled. Refer to section 3.1.4 to select a Weather channel.
NOTE
If the Weather Watch function is not available (for example, if
no Weather channels are programmed into the radio), the display will show “Wx Not Enabled”.
To cancel Weather Watch, press Shift followed by the User key
(Wx Watch).
6.1.1
Weather Watch alert
If a Weather Alert tone is detected by the radio on the specified
Weather channel while Weather Watch is enabled, the radio
will sound a 10 second alarm and the display will show
“Weather Alert”.
Press Ok to cancel the alarm and switch to the Weather channel, or On/C to cancel the alarm and ignore the Weather Alert.
NOTE
Because the Weather channels transmit a continuous carrier
signal, it is not possible for the RS87 to detect when the transmission has ended.
Press On/C to return to the working channel once the transmission has ended.
Part No. E04297
49
RS87 VHF
6.2 Security mode (voice scrambler)
For additional security, a voice scrambler function is available
as an optional accessory. The scrambler uses frequency inversion to encrypt the transmission and will allow secure transmission between compatible radios.
To enable Security mode press Shift followed by 0 (Scrm). The
display will show “Sec” indicating that Security mode is on.
To exit Security mode, press Shift followed by 0 (Scrm) again,
or press On/C. Security mode will be cancelled if the RS87 is
placed into another mode that requires the use of the PTT key
(i.e Hailer/Intercom) or if a DSC call is made/received.
6.3 Editing Latitude, Longitude and UTC
Normally, position and time data should be supplied to the
RS87 via a GPS or other navigational device connected to the
radio. However, if this is not possible, the position and time
can be entered manually Press Shift then 8 (Lat/Lon). The display will show “Enter Lat”.
Enter the Latitude using the numeric keypad (Fig 6.2). Use the
Call and MSG keys to move the cursor to correct any
errors. The cursor position is indicated by the number flashing.
Enter a new number to overwrite the incorrect number.
INT
12
ENTER LA T A
LA 52-B--Fig 6.2 - Manually entering position
The final digit specifies whether the Latitude is north or south
of the Equator - press VOL or VOL to toggle between N
and S.
Press Ok to confirm and move on to entering the Longitude the display will show “Enter Long” - or On/C to abort entry.
Enter the Longitude using the numeric keypad. Use the Call
and MSG keys to move the cursor to correct any errors. The
cursor position is indicated by the number flashing. Enter a
new number to overwrite the incorrect number.
50
Part No. E04297
Instruction Manual
The final digit specifies whether the Longitude is west or east
of the Meridian - press VOL or VOL to toggle between W
and E.
Press Ok to confirm and move on to entering the time - the display will show “Enter UTC” - or On/C to abort entry.
Enter the UTC time (formerly known as GMT) in 24hr format
using the numeric keypad (Fig 6.3). Use the Call and MSG
keys to move the cursor to correct any errors. The cursor position is indicated by the number flashing. Enter a new number
to overwrite the incorrect number.
INT
12
ENTER U T CA
UTC 19B---Fig 6.3 - Manually entering time (UTC)
Press Ok to confirm all settings or On/C to abort entry.
WARNING
6.4
This data is only stored temporarily and will be lost when the
radio is switched off. Since the accuracy of this information is
vital in the event of a Distress Alert transmission being necessary, we strongly recommend that a GPS or other navigational
device is permanently interfaced with the radio. This data will
then be automatically supplied and updated without the need
for user intervention.
Toggling between Lat/Long and UTC views
If the Position View option (see section 3.3.2) is turned on, the
current position will be displayed on the bottom two lines of
the display.
The UTC time can be displayed instead by pressing Shift then
holding the 8 (Lat/Lon) key down for two seconds (Fig 6.4) -
UTC 19B26Fig 6.4 - Displaying UTC time
Repeat the above key sequence to toggle between the Position
and Time displays.
Part No. E04297
51
RS87 VHF
6.5
Intercom
If the system comprises of more than one station and/or
includes intercom speaker/s, it is possible to make an intercom
call to a selected position from a handset.
NOTE
This assumes that the installation comprises a full expanded
RS87 system with four stations and two intercom speakers.
The options shown will only be available if the relevant stations / intercoms are installed.
6.5.1 Making an intercom call
Press Shift then 6 (Intercom) to enter Intercom mode. The display will show “Intercom Stn X - Stn Y”, where “X” is the I/D
of the current station being used and “Y” is the first of the
other stations in the system (Fig 6.5) -
INT
12
I N T ERCOMAA
STN 1 -STN2 B
Fig 6.5 - Making an intercom call to station 2 from station 1
Press the VOL and VOL keys to scroll through the available stations / intercoms that can be called from the station “Stn 1–Stn 2”
“Stn 1–Stn 3”
“Stn 1–Stn 4”
“Int Spkr 1”
“Int Spkr 2”
“All Spkrs”
“P A”
Intercom call to Station 2
Intercom call to Station 3
Intercom call to Station 4
Intercom call to Intercom speaker 1
Intercom call to Intercom speaker 2
Intercom call to all Station speakers
Intercom call to all speakers in system
(including horns)
Press the PTT key or Ok to activate the intercom or press
On/C to cancel. Once the call has been initiated, further presses of the Ok key will re-sound the call alarm. Pressing the
PTT key will open the audio path to the called station.
NOTE
52
The call will be terminated if it is not accepted within 15 secs.
Part No. E04297
Instruction Manual
If calling an Intercom speaker, pressing the VOL and VOL
keys while the PTT key is held to adjust the Intercom speaker
volume. This option is not available if calling another Station
or making an All Speaker / PA call - the current volume settings for each position will be used.
To end the intercom call, press On/C or return the handset to
its cradle.
NOTE
While making an intercom call, all other stations will display
“Station X Occupied”.
NOTE
If the Interrupt Intercom option (section 3.3.4) is disabled and a
VHF transmission is being received, the display will show
“Signal Present” until the transmission has ended. If Interrupt
Intercom is enabled, the intercom call will be interrupted if a
VHF transmission is received.
6.5.2 Receiving an intercom call
If an intercom call is received from another station, the display
will show “Intercom From Stn Y”, where “Y” is the I/D of the
Station making the intercom call (Fig 6.6) -
INT
12
I N T ERCOMAA
FROM STN 22
Fig 6.6 - Receiving an intercom call from station 2
If the other station is making an All Speakers call, the display
will show “Int All From Stn Y”.
If the other station is making a PA call, the display will show
“P A from Stn Y”.
To accept the call lift the handset from the cradle or press On/C
to cancel the intercom call.
To end the intercom call, press On/C or return the handset to
its cradle.
NOTE
Part No. E04297
All speaker and PA calls are announcement calls and therefore
do not need to be accepted manually by the receiving stations.
53
RS87 VHF
6.6 Loudhailer / Foghorn
Up to two loudhailer / foghorns can be fitted to the RS87 - one
Fore and one Aft.
To enter Hailer / Foghorn mode press Shift then 5 (Hail/Fog).
The display will show “Loudhailer Fwd” (Fig 6.7) -
INT
12
LOUDHA I LER
FWDM STN 22
Fig 6.7 - Selecting Foghorn mode
To toggle between Loudhailer and Foghorn press the 5 key the display will show “Foghorn Fwd”.
NOTE
If no hailers are connected to the radio the display will show
“Horns not enabled”.
6.6.1 Loudhailer
To cycle through the loudhailer options press the 4 key Loudhailer Fwd
Loudhailer Aft
Loudhailer Both
NOTE
If a single loudhailer is fitted, only the “Loudhailer Fwd” or
“Loudhailer Aft” option will show, depending on where fitted.
Press the PTT key to make the loudhailer call. Press the
VOL and VOL keys while the PTT is pressed to adjust the
hailer volume.
Press Ok to open the talkback path, enabling users at the loudhailer to talk back.
Press the On/C key to exit Loudhailer /Foghorn mode.
NOTE
54
If Interrupt Intercom is disabled (see section 3.3.4) the display
will show “Signal Present” if an incoming VHF transmission is
being received.
Part No. E04297
Instruction Manual
6.6.2 Foghorn
To select Foghorn press the 5 key while in Loudhailer /
Foghorn mode - the display shows “Foghorn Fwd” (Fig 6.8) -
INT
12
FOGHORN AA
FWDM STN 22
Fig 6.8 - Selecting Foghorn mode
To cycle through the foghorn options press the 4 key Foghorn Fwd
Foghorn Aft
Foghorn Both
NOTE
If a single loudhailer is fitted, only the “Foghorn Fwd” or
“Foghorn Aft” option will show, depending on where fitted.
Press Ok to enter the Foghorn sub menu. Use the VOL and
VOL keys to scroll through the available horn tone options Horn
Siren
Power Vessel Under Way
Power Vessel Stopped
Restricted Manoeuvre
Working at anchor
Vessel Being Towed
Vessel In Pilotage
Anchor
Aground
Press PTT or Ok to sound the horn. If an external horn button
is fitted to the radio, pressing this will also sound the horn.
NOTE
For single activation options (eg Horn), it is necessary to press
the activation button each time to sound the horn. For automatic repeat options (eg Anchor) it is only necessary to press
the key once and the foghorn will sound automatically. Press
On/C to cancel the automatic repeat sequence.
Adjusting horn volume - for single activation options press the
VOL and VOL keys while the PTT is pressed. For automatic repeat options, press VOL and VOL while the display shows “Horn In Use”.
ctd -
Part No. E04297
55
RS87 VHF
Press the On/C key to exit Loudhailer /Foghorn mode.
NOTE
Ten seconds after the automatic horn is sounded the unit will
revert to normal radio operation, but the horn will continue to
sound. To cancel, press Shift followed by 5 (Hail/Fog), then
On/C.
6.7 Station speaker mute
The station speaker that is installed alongside the handset can
be muted if required.
To mute the speaker, press Shift followed by 7 (Speaker) on the
specific handset that is used with the speaker.
To disable mute, press Shift followed by 7 (Speaker) again, the
VOL and VOL keys or lift the handset from the cradle. If
the system is powered down, the speaker will be un-muted
when the system is turned on again.
NOTE
This will only affect the speaker that is used with this specific
handset - eg handset 1 will only mute the speaker connected to
the Station 1 terminals. To mute any other speakers on the system it will be necessary to go to the relevant handset and select
mute.
6.8 iDSC
The RS87 can be integrated with one of Simrad’s navigational
displays (33, 42 and 52 series) enabling details of any incoming
DSC calls to be displayed on the unit. Refer to the instruction
manual of the relevant unit for more details. Refer to section
7.2.5 for interfacing details.
56
Part No. E04297
Instruction Manual
7 INSTALLATION
7.1 Physical Installation
The RS87 is a modular system that is very simple to install,
however the performance of the radio is directly affected by the
quality of the installation. Please read these instructions thoroughly before attempting installation and if in any doubt, consult a qualified marine electronics engineer.
7.1.1 Transceiver Installation
The transceiver unit is designed to be installed in a concealed
location such as in a locker or behind the switch panel.
CAUTION
The transceiver unit is not waterproof, therefore it must not be
installed in any location where it is likely to be exposed to
excess moisture (eg a wet locker or an outside locker).
The fins on the top of the transceiver act as a heatsink to dissipate heat generated by the set when in use, which maintains
the high efficiency of the radio. The free circulation of air is
essential - if mounting the transceiver in an enclosed space,
ensure that the space is well ventilated
The transceiver requires a flat surface with an area of at least
170 x 245mm (6.8 x 9.8in) for mounting. Allow sufficient space
beneath the unit to allow cable entry - at least 50mm (2.0in) is
recommended. The surface should be rigid and sturdy enough
to be able to support the weight of the unit, taking into account
the shock loads likely to be encountered when the vessel is
underway in heavy seas.
Fix the transceiver unit to the surface using the four self-tapping screws supplied. The four fixing points are at the corners
of the transceiver unit -the bottom two are underneath the terminal cover (Fig 7.1) -
Fig 7.1 - Transceiver box mounting
Part No. E04297
57
RS87 VHF
7.1.2 Handset Installation
The handset should be sited so that engine noise and vibration
or other background noise do not make it difficult for the operator to hear.
As microphones and loudspeakers contain powerful magnets,
the handset and speakers should not be installed within 1m
(3ft 3in) of any compasses, whether magnetic or electronic.
The handset is connected to a 5m (16.5ft) extension cable, therefore the handset should be fitted within reach of the transceiver
box (for longer runs, 20m extension cables are also available as
separate accessories - see section 8.6).
The handset cradle should be mounted on a flat surface with
enough space to allow the bulkhead socket for the extension
cable to be fitted alongside. Space should also be allowed nearby for the accompanying loudspeaker to be fitted.
NOTE
The handset and bulkhead socket are waterproof, but if the
handset is to be fitted in an exposed location (for example on
the flybridge of a power boat) it is recommended that the
handset and especially the bulkhead socket is fitted to an
angled or vertical surface to prevent standing water lying on
the handset face or inside the bulkhead socket, which could
corrode the pins.
Fit the supplied template for the handset cradle to the desired
mounting location. Drill 4 x3.2mm (0.125in) pilot holes in the
indicated positions. If drilling into GRP, it is recommended
that the holes are also countersunk to prevent the gelcoat splitting when the self-tapping screws are inserted.
Fit the supplied template to the desired mounting location for
the bulkhead socket. Drill a 23.5mm (0.94in) hole and 4 x
2.4mm (0.1in) pilot holes. Again, the pilot holes should be
countersunk if drilling into GRP.
Fit the bulkhead socket and run the cable to the transceiver box
position.
NOTE
It is recommended that the cable is routed away from any other
cables carrying high current (eg mains power cables) or pulsed
signals (eg transducer cables) to avoid possible interference.
If the handset is being removed, the waterproof cover should
always be fitted to the bulkhead socket to protect the pins from
possible corrosion.
58
Part No. E04297
Instruction Manual
7.1.3 Station speaker Installation
The loudspeaker should be installed near to the handset and can
be flush mounted or surface mounted with the supplied pattress.
Flush Mounting
Attach the self adhesive gasket to the back of the loudspeaker.
Remove the four detachable corners of the speaker which conceal the mounting holes. Apply the supplied cutting template
to the mounting position. Carefully cut out the aperture
required for the speaker back and use the short self tapping
screws provided. Refit the corners to conceal the screw fixings.
Surface Mounting
Drill a 5mm (0.2in) hole for the speaker cable. Attach the self
adhesive gasket to the back of the loudspeaker. Remove the
four detachable corners which conceal the mounting holes. Fit
the pattress to the back of the speaker and use the long self-tapping screws provided to fix the speaker and the pattress block
to the bulkhead. Refit the corners to conceal the screw fixings.
7.2 Electronic Installation
Electronic installation is straightforward - all peripherals connect to the Transceiver Unit using the clearly labelled plug-in
terminals (Fig 7.2) -
STANDARD CONNECTIONS
EXPANSION BOARD
Fig 7.2 - Transceiver terminal connections
NOTE
The diagram shows the terminal bay with the optional expansion board, which is not included with the standard radio.
If it is necessary to shorten any of the cables, ensure the ends
are re-tinned for the best quality connection.
The transceiver unit is fitted with a 10amp “blade” type fuse.
It is recommended that the radio is connected to a 10amp
fused switch or breaker on the boat’s switch panel.
Connect the supplied power cable to the terminals marked
PWR + and - as follows -
Part No. E04297
Terminal
Number
Wire
Colour(s)
Red
Black
59
RS87 VHF
7.2.1 Control panel
A single cable links the control panel to the transceiver unit.
The standard model can support up to two control stations, or
up to four stations if the expansion board is fitted. One fixed
station is supplied with the radio - additional stations are supplied as separate accessories. The control stations can be either
a handset model which is supplied with a separate loudspeaker or a fixed control panel with a passive fistmike or handset.
Connect the main control station to the “Station 1” terminals on
the transceiver unit as shown (Fig 7.3) -
Terminal
Number
Wire
Colour(s)
Brown
Green
Red
White
Blue
Yellow
Orange
Black
Fig 7.4 - Control panel terminal connections
Additional control stations should be wired in the same manner and connected to the “Station 2”, “Station 3*” and “Station
4*” terminals (Fig 7.5).
* Only available on models fitted with the expansion board
Station 1
Station 3*
Station 2
Station 4*
Fig 7.5 - Example of a typical multi-station installation
60
Part No. E04297
Instruction Manual
7.2.2 Loudspeakers
The RS87 can be fitted with Simrad LS80 station speakers or
third party station speakers with an impedance of 4Ω.
Connect the station speaker to terminals 7 and 8 of a free
Station terminal strip (Fig 7.6).
Terminal
Number
Wire
Colour(s)
Orange
Black
Fig 7.6 - Station loudspeaker terminal connections
7.2.3 Intercoms
NOTE
Only available on units fitted with the expansion board.
The RS87 intercoms enable two-way onboard communication
with the main stations but do not allow control or use of VHF
or DSC functions. Intercoms are normally fitted in areas such
as the engine room, galley or crew quarters. Up to two intercoms can be fitted to the RS87.
Connect the intercoms to the “Int 1” and “Int 2” terminals on
the transceiver unit as shown (Fig 7.7) -
Terminal
Number
Wire
Colour(s)
Black
Red
White
Fig 7.7 - Intercom terminal connections
Part No. E04297
61
RS87 VHF
7.2.4 Loudhailer/Foghorns
NOTE
Only available on units fitted with the expansion board.
Two separate loudhailer/foghorns can be fitted to the RS87
(normally one is mounted on the fore of the boat, the other aft).
Connect the loudhailers to the “Aft/Fwd Hailers” terminals on
the transceiver unit as appropriate (Fig 7.8) -
Terminal
Number
Wire
Colour(s)
Aft +
Aft -
Fore +
Fore -
Fig 7.8 - Loudhailer terminal connections
WARNING
Do not connect any of these terminals to a common ground,
otherwise the RS87 will be permanently damaged.
NOTE
Only available on units fitted with the EHX80 expansion board.
7.2.5 Remote foghorn button
A remote button can be used to activate the foghorn. Connect
the remote button to the terminals marked “Horn Key” as
shown (Fig 7.9) -
Terminal
Number
Wire
Colour(s)
Red
Blue
Fig 7.9 - Remote foghorn button terminal connections
NOTE
62
Apart from when transmitting, pressing this button will enable
the foghorn to be sounded at any time, regardless of what
mode the RS87 is currently in.
Part No. E04297
Instruction Manual
7.2.6 Auxiliary audio input
NOTE
Only available on units fitted with the EHX80 expansion board.
The expansion board upgrade on the RS87 allows an auxiliary
audio input - for example from a radio receiver or an entertainment system - to be fed into the intercom / loudspeaker system.
The auxiliary input must be a line level signal (0.775V rms)
Connect the line out from the auxiliary source to the terminals
marked “Aux AF” as shown (Fig 7.10) -
Terminal
Number
Wire
Colour(s)
Line Out +
Line Out -
Fig 7.10 - Auxiliary audio input terminal connections
7.2.7 NMEA0183 input
The inbuilt NMEA0183 processor allows navigational position
information to be received from a GPS or Chart Plotter. The
boat’s position is automatically transmitted when a Distress
Alert is initiated.
NMEA input must be of the 0183 format, version 2.0 - 3.0, outputting sentences GLL, RMC and ZDA at a Baud rate of 4800.
The NMEA Out connections from the GPS/Plotter should be
connected to the “NMEA In” terminals as shown (Fig 7.11) -
Terminal
Number
Wire
Reference
Common Out Data Out +
Fig 7.10 - Auxiliary audio input terminal connections
Part No. E04297
63
RS87 VHF
7.2.8 iDSC output
The RS87 is designed to integrate with other Simrad equipment
which enables DSC call information to be displayed on the
xx33, xx42 and xx52 series chartplotters.
Connect the iDSC input terminals of the chartplotter to the terminals marked “iDSC” as shown (Fig 7.11) -
Terminal
Number
Wire
Reference
iDSC iDSC +
Fig 7.11 - iDSC output terminal connections
7.2.9 Future options
The two circular ports in the centre of the connection panel are
reserved for future options (Fig 7.12) -
Reserved
for future
options
Fig 7.12 - Future options
64
Part No. E04297
Instruction Manual
7.2.10 Summary
Summary of the RS87 connections -
STANDARD CONNECTIONS
EXPANSION BOARD
STANDARD CONNECTIONS
Station 1
Station 2
Terminal
Number
Wire
Colour(s)
Brown
Green
Terminal
Number
Wire
Colour(s)
Brown
Green
Red
White
Blue
Red
White
Blue
Yellow
Orange
Black
Yellow
Orange
Black
PWR
NMEA/iDSC
Terminal
Wire
Number
Reference
Common Out 2
Data Out +
Terminal
Number
Wire
Reference
Red (12v in)
Black (0v)
iDSC iDSC +
EXPANSION BOARD CONNECTIONS
Station 3
Station 4
Fog/Hailers
Terminal
Number
Wire
Colour(s)
Brown
Green
Red
Terminal
Number
Wire
Colour(s)
Brown
Green
Red
Terminal
Number
Wire
Colour(s)
Aft +
Aft Fore +
White
White
Fore -
Blue
Yellow
Orange
Black
Blue
Yellow
Orange
Black
Intercoms
Terminal
Number
Horn Key
(Int1/Int2)
Wire
Colour(s)
Black
Red
White
Aux AF
Terminal
Number
Wire
Colour(s)
Red
Terminal
Number
Wire
Colour(s)
Line Out +
Blue
Line Out -
Fig 7.13 - Transceiver unit connections summary
Part No. E04297
65
RS87 VHF
7.2.11 Cable strain relief
Once all the cables have been run to the appropriate peripherals and connected to the transceiver unit they should be
secured to ensure that they are not snagged or exposed to
excess strain.
Screw the strain relief tabs to the cable exit port on the transceiver unit using the screws supplied and secure the cables to
the tabs using tie wraps as shown (Fig 7.14) -
Fig 7.14 - Cable strain relief
Replace the terminal cover and secure by tightening the retaining screw.
7.3 Antenna installation
The most important factor in the performance of the radio will
be the quality and positioning of the antenna. Most recorded
problems with VHF radios are related to poor antenna siting,
faulty cabling, poor quality cable joints and low voltage supply. Even a VHF as highly advanced as the RS87 cannot compensate for these factors. Therefore, if replacing an existing
VHF installation, it is important that the antenna is thoroughly
checked for any faults or damage before use.
As the range of VHF signals are governed by line of sight (see
section 8.3), the antenna should be placed as high as possible,
while remaining clear of any metallic objects that could influence the resonance of the antenna.
The most popular antennae for marine use are 1m (3ft 3in)
long. On sail boats these are usually mounted on the masthead, where the length of the antenna keeps it clear from the
navigation lights and windvanes etc. This type of antenna can
also be mounted on the cockpit roof or garage of power boats.
Longer whip antennae are recommended for larger boats these radiate the same total power as smaller antennae, but
concentrate it into a narrower beam, which is advantageous on
a tall mast at extreme range where concentrating the available
power into a narrow horizontal beam becomes more impor-
66
Part No. E04297
Instruction Manual
tant. However, if the antenna is not vertical when transmitting,
the beam will be angled either too high or too low (Fig 7.15) -
Fig 7.15 - Effect of heel on range of longer whip antenna
Here the wider beam of the shorter antenna will be more universally effective, although the signal will be weaker (Fig 7.16) -
Fig 7.16 - Effect of heel on range of 1m marine antenna
Therefore vessels with a large heel angle (small sailboats)
would be better choosing a short masthead antenna. Your
local agent should be able to provide specific advice on antenna choice for the vessel it is to be fitted to.
WARNING
The antenna coaxial cable and any connectors used must be
rated at 50Ω. Under no circumstances should standard domestic
TV cable and connectors be used. Incorrectly rated cabling and
connectors could result in power not reaching the antenna, but
also power could be reflected back into the radio, damaging it
in the process.
The quality of any connections and integrity of the cable (without breaks in the sheathing) will directly affect the performance
of the radio. Poor soldering or corrosion of the terminals can
impair performance. We recommend that screw or crimp terminal type connectors are not used for any through deck fittings - a good quality waterproof solder terminal connector will
be less susceptible to poor connection due to corrosion of the
contacts.
Part No. E04297
67
RS87 VHF
To ensure the best performance of the radio, the antenna cable
should be routed where it is least likely to interfere with, or
receive interference from other electronic equipment, such as
echosounder transducer cables and high current carrying
cables.
The antenna cable should terminate in a standard marine
PL259 plug fitting. Connect the antenna plug to the socket on
the top of the transceiver unit and screw the retaining collar
down (Fig 7.17) -
Fig 7.17 - VHF antenna connection
NOTE
To avoid possible water damage to the radio, it is recommended that the antenna cable is looped to provide a drip path.
7.4 Electrical interference suppression
Interference generated by the alternator of the engine may
occasionally cause problems. The RS87 has been designed to
minimise the effects of outside interference. However, precautions should still be taken - route the power supply and antenna cables away from the engine compartment. The cable run
should not be down the same trunking as other cables carrying
high current. The antenna cable should also be kept separate
from the radio’s power cable.
Engines with spark ignition - and also some refrigerators should be fitted with suppressors. Your local agent should be
able to give advice on this, and also supply suppression kits
where necessary.
68
Part No. E04297
Instruction Manual
8 APPENDIX
8.1 Operating procedures
The following operating procedure summary has been proposed by the UK Maritime and Coastguard Agency. It is not
exhaustive and should not be regarded as a replacement for
information provided by the proper two day VHF/DSC training course required for all VHF license holders.
8.1.1 Sending a distress alert
1. Send a distress alert call (see section 2.7)
2. Wait approx 15 seconds for a DSC acknowledgement from
the Coastguard or a ship station.
3. On receipt of a DSC acknowledgement or after about 15
seconds, transmit the Distress call on channel 16 “Mayday, Mayday, Mayday”
“This is (name of vessel repeated three times)
“Mayday”
MMSI number and name of vessel or callsign, spoken once
Position
Nature of distress
If the vessel is not in “grave and imminent danger”, an All
Ships Urgency call followed by a spoken “Pan Pan” call or a
routine call to the nearest coastguard station may be more
appropriate. It is a prosecutable offense to initiate a Distress
Alert call for any other reason than that the vessel and/or crew
is in imminent danger.
8.1.2 Acknowledging and relaying a
distress alert
When a DSC distress alert is received, an audible alarm will
sound. Immediately cease any transmission that may interfere
with distress traffic and continue a watch on channel 16.
If there is no DSC acknowledgement from a coast station or
ship, after a short interval acknowledge by voice on channel 16 “Mayday (MMSI of vessel in distress repeated three times)”
“This is (name of own vessel, repeated three times)”
“Received Mayday”
(State the assistance you can give).
A similar response should be given to a distress relay, using the
words “Mayday Relay” instead of “Mayday”.
Part No. E04297
69
RS87 VHF
8.1.3 Cancelling a distress alert
If a DSC distress alert is sent accidentally, cancel it immediately
on the RS87 by pressing the C button to prevent repeats, then
make the following announcement on channel 16 “This is (name of vessel, callsign, MMSI)”
“Cancel DSC Alert sent (date & time UTC)”
Do not simply cancel the DSC alert without verbally cancelling
it as well, otherwise the rescue authorities will not be aware
that this is a false alarm.
8.1.4 Alerting all vessels within range
If the vessel is outside of coast radio range and needs to issue a
safety warning to all vessels within radio range, transmit an All
Ships Safety call by DSC. After about 15 seconds transmit on
channel 16 the safety call and message as follows “Securité, Securité, Securité”
“All stations (or called station)” repeated three times
“This is (MMSI and name or callsign of own vessel)”
Repeat text of safety message.
8.1.5 Calling a coast radio station
Enter the MMSI of the station into the RS87, either manually
or from the directory. When the call is acknowledged, the
working channel for voice communication will be indicated
and the RS87 will automatically switch to that channel. Make a
voice call as normal.
8.1.6 Making an intership call
Enter the vessel’s MMSI into the RS87, either manually or from
the directory. Before sending the call, enter the inter-ship channel to be used for subsequent communication. When the alarm
sounds on the called vessel, its operator should acknowledge
by DSC, then respond by voice on the selected channel.
If the MMSI number of the vessel is not known, call as now on
channel 16. If no response is received, call on channel 13. This
is the GMDSS bridge to bridge communication channel.
8.2 NMEA sentences received
The following NMEA0183 sentences are processed by the RS87
in order to transmit the boat’s position if a Distress Alert is initiated NMEA0183 version 2 and 3 - GGA, GLL, RMC, ZDA
70
Part No. E04297
Instruction Manual
8.3 Transmission range
Because VHF signals travel in a straight line and are not reflected back off the ionosphere as lower frequency signals are, the
range of VHF signals is limited to ‘line of sight’, beyond which
the other vessel passes behind the curve of the Earth.
Therefore, the range will increase greatly the higher above sea
level the antenna is, as Fig 8.1 illustrates (assuming maximum
transmission power is used):
Fig 8.1 - VHF transmission range
Therefore, the typical ship to ship range of a fixed VHF radio
such as the RS87 with a masthead antenna will be approximately 20 Km (12 miles). This will increase as height above
sea level increases, or if the other radio user’s antenna is at a
greater height - note that the range between the yacht with the
antenna mounted on a 9 M (30 Ft) mast and the shore station
increases to 46-53 Km (29-33 Miles).
Part No. E04297
71
RS87 VHF
8.4 Frequency of channels
NOTE
Ch 0 will only be made available in the UK to Coastguard
users with written authorisation.
Channel 70 is the designated Digital Selected Calling (DSC)
channel and may not be used for voice transmissions.
72
Part No. E04297
Instruction Manual
8.5 Fault finding
Symptom
Possible Cause
Remedy
Unit will not switch on
• Faulty connection to power
• Fuse has blown
• Check power connection
• Replace fuse and check
power supply current
• Check supply voltage is
less than 15.6v
• Supply voltage above limit
Scan or Memory Scan is
locking on a channel
without a signal
• Noise on the channel is
holding the scan
• Increase squelch level
• Inhibit channel from scan
(see section 2.11.1)
Dual Watch not being
entered
• Priority channel selected
• Handset off cradle
• Select a working channel
• Replace handset
Cannot change channel
• Dual Watch (D/W) engaged
• Exit Dual Watch
Certain channels are
not obtainable
• Some channels are restricted
and not programmed depending on country of purchase
• Consult your national
authority for permitted
channels in your region
Will not transmit
• Scanning or D/W function active
• Exit D/W or Scan
Will not transmit on 25W • Low voltage when full transmitbut OK on 1W
ting current is drawn
• Some channels are restricted to
low power transmission only
• Check power supply
Transmissions persistently • Damaged antenna
weak/display flashes
• Antenna cable broken
ANT
• Poor contact
• Replace antenna
• Replace cable
• Check antenna sockets &
through deck connector
• Consult your national
authority
These simple checks should be carried out before seeking technical assistance and may save time and expense. Before contacting your servicing agent please obtain the radio’s serial
number. The software iteration should also be quoted - this is
shown in the large digits on the display for 2 seconds after the
radio is turned on and should be written in the box below for
future reference.
Part No. E04297
73
RS87 VHF
8.6 Optional Accessories
The following accessories are available from your nearest
Simrad Technical Dealer. Please quote the correct part number
when ordering.
AHK87
Active Handset Kit
(includes 20m cable)
PCK86:F or PCK86:H
Fixed control panel
(Available with fistmike or telephone handset)
LS80
Loudspeaker
74
LS81
Intercom Speaker
Part No. E04297
Instruction Manual
5.6 Technical specification
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . 12v DC (10.8v - 15.5v DC)
Channel Capability . . . . . . . . . . . . . . . . . . . . . 55 international channels
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-28, 60-88 simplex & semi-duplex
. . . . . . . . . . . . . . . . . . . . . . . . UK : includes M (previously 37) and M2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USA : Wx1-10 receive only.
. . . . . . . . . . . Scandinavia : leisure or fishing channels as appropriate.
. . . . . . . . . . . . . . . . . . . . . . . . . . Canada : Canadian and USA channels.
Private Channels . . . . . . . . . . . . . . . . . . . . . Up to 18 private channels*
External Speaker Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Ω
* Contact local Simrad Technical Dealer for further details of channel programming etc.
Transmit
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155-163Mhz
Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 watt or 25 watts
Current Consumption . . . . . . . . . . . . . . . 5.5A (25 watts), 1.3A (1 watt)
Harmonic and Spurious Emissions . . . . . . . . . . . . . . . . . . . . . < 0.25µW
Hum / Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < -40dB
Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±5kHz
Receive
Audio Output Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 watts
Current Consumption . . . . . . . 600mA (Full Volume, illumination on)
. . . . . . . . . . . . . . . . . . . . . . . 220mA (Fully Squelched, illumination off)
Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . < 1µV emf for 20 dB SINAD
Harmonic and Spurious Emissions . . . . . . . . . . . . . . . . . . . . . . . < -2nW
Hum / Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < -40dB
Adjacent Channel Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70dB
Intermodulation Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70dB
Environmental
Telephone Handset & Loudspeakers . . . . . . . . . . . . Waterproof to IP67
5.7 Dimensions
243mm (9.72in)
168mm (6.72in)
45mm
(1.8in)
48mm
(1.9in)
110mm (4.4in)
110mm (4.4in)
190mm (7.6in)
70mm (2.8in)
63mm
(2.5in)
45mm
(1.8in)
Part No. E04297
75
RS87 VHF
5.8 Declaration of Conformity
English
Hereby, Simrad Limited (Margate), declares that this RS87 VHF Radio is in
compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Finnish
Simrad Limited (Margate) vakuuttaa täten että RS87 VHF Radio tyyppinen laite
on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin
muiden ehtojen mukainen.
Dutch
Hierbij verklaart Simrad Limited (Margate) dat het toestel RS87 VHF Radio in
overeenstemming is met de essentiële eisen en de andere relevante bepalingen van
richtlijn 1999/5/EG
French
Par la présente, Simrad Limited (Margate) déclare que ce RS87 VHF Radio est
conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE
qui lui sont applicables
Swedish
Härmed intygar Simrad Limited (Margate) att denna RS87 VHF Radio står i
överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser
som framgår av direktiv 1999/5/EG.
Danish
Undertegnede Simrad Limited (Margate) erklærer herved, at følgende udstyr RS87 VHF
Radio overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF
German
Hiermit erklärt Simrad Limited (Margate), dass sich dieses RS87 VHF Radio in
Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten
Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi)
Greek
Με την παρουσα Simrad Limited (Margate) δηλωνει οτι RS87 VHF Radio
συµµορφωνεται προζ τιζ ουσιωδειζ απαιτησειζ και τιζ λοιπεζ σχετικεζ διαταξειζ τηζ
οδηγιαζ 1999/5/ΕΚ
Italian
Con la presente Simrad Limited (Margate) dichiara che questo RS87 VHF Radio
è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva
1999/5/CE.
Spanish
Por medio de la presente Simrad Limited (Margate) declara que el RS87 VHF Radio
cumple con los requisitos esenciales y cualesquiera otras disposiciones
aplicables o exigibles de la Directiva 1999/5/CE
Portuguese Simrad Limited (Margate) declara que este RS87 VHF Radio está conforme com
os requisitos essenciais e outras provisões da Directiva 1999/5/CE.
Website - www.simrad.com
76
Part No. E04297
Instruction Manual
5.9 Service & warranty
Your radio should seldom need servicing, although it will benefit from an application of silicone or Teflon grease to the antenna and mic sockets each season. The equipment should be regularly checked by making routine calls to other stations. On an
annual basis, test the Distress Alert button by pressing it ONCE.
This will display the Distress Alert screen and ensure that the
button is functioning. Press On/C to return to the main screen DO NOT HOLD DOWN THE DISTRESS BUTTON.
The unit is guaranteed for 2 years from date of retail sale. If it
is necessary to have the unit repaired, return it carriage prepaid
to the agent in the country of purchase with a copy of the
receipted invoice showing the date of purchase. Where possible, return all the components unless you are certain that you
have located the source of the fault. If the original box is not
available, ensure that it is well cushioned in packing; the
rigours of freight handling can be very different from the loads
encountered in the marine environment for which the unit is
designed.
For Worldwide Warranty details, please refer to the Warranty
Card supplied with this unit.
Part No. E04297
77
www.simrad.com
A L W A Y S
A T
T H E
F O R E F R O N T
O F
T E C H N O L O G Y

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Create Date                     : 2003:03:06 16:48:04Z
Modify Date                     : 2003:03:06 16:48:04Z
Page Count                      : 80
Creation Date                   : 2003:03:06 16:48:04Z
Mod Date                        : 2003:03:06 16:48:04Z
Producer                        : Acrobat Distiller 5.00 for Macintosh
Author                          : martinl
Metadata Date                   : 2003:03:06 16:48:04Z
Creator                         : martinl
Title                           : RS87_Manual.qxd

EXIF Metadata provided by EXIF.tools