Sonim Technologies VK01011AA Bluetooth PTT Car Kit User Manual Use Manual
Sonim Technologies, Inc. Bluetooth PTT Car Kit Use Manual
Use Manual.pdf
Owner’s / Installation Manual Bluetooth PTT Car Kit for XP6® & XP7® AVK01G For support, please call (888) 858-9460, or visit www.sonimtech.com Introduction Please take the time to read all of the information in this manual. Familiarity with operation and installation procedures will help you obtain the best possible performance from your new Bluetooth PTT Car Kit for XP6® & XP7®. This car kit is intended to be installed by a professional installer WARNING: Changes or modifications made to this equipment not expressly approved by Sonim Technologies, Inc. for compliance could void the user’s authority to operate the equipment. FCC Statement • This device complies with part 15 of the FCC rules (FCC ID: WYPVK01011AA). Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. • This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. CE Statement This device complies with the R&TTE directive (1999/5/EC), the EMC Directive (2004/108/ EC), and the Low Voltage Directive (2006/95/EC) issued by the Commision of the European Community. IC Statement This device complies with RSS-310 of Industry Canada (IC:8090A-VK01011AA). Operation is subject to the following two conditions: 1. This device does not cause harmful interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. CE Mark & NB Identification Number 1797 Includes: 1.) Cradle 2.) Speaker with 2m cable 3.) PTT Button with 2m cable 4.) Microphone with 2m cable 5.) 2m Wiring Harness 6.) Mount 7.) Screws: Speaker (2) -12.5 x 15.0mm Mounting Bracket (4) - 6.5 x 12.0mm XP6-XP7 Width Adjustment Optional Padlock Location (3mm lock) Phone Lockdown Latch Mount Holes Width Adjustment Release Button Speaker Sonim USB Connector USB Port Bluetooth Pairing Button PTT Button or Optional Foot Pedal (sold seperately) Microphone or Optional Gooseneck Mic Optional Palm Mic (sold seperately) (sold seperately) LED Status Light Power Mounting Bracket The mounting bracket gives the convenience and adjustability to have the car kit installed where the vehicle operator needs and wants it. The bracket should be installed in a location that does not interfere with the normal operation of the vehicle or over the vehicles air bag deployment areas. The mount attaches to the back of the car kit with 4 supplied screws. Mount to vehicle screws are not included with this car kit. Please consult your installer for the appropriate screws for your installation. Speaker Installation The speaker should be mounted on the passenger side of the vehicle beneath the dashboard at least 4 feet away from the Car Kit. Do not mount on rear window shelf or on the dashboard. 1. Remove the bracket from the speaker by loosening the side thumb screws. 2. Using the mounting bracket as template, drill the mounting holes and attach it to your selected location with the provided selftapping screws. 3. Reattach the speaker to the mounting bracket tightening it down to your preferred angle. 4. Plug the speakers blue connection end into the back of the Car Kit’s corresponding blue socket. PTT Button 1. For gear shift PTT attachment, install and use the supplied velcro strip. 2. To place the PTT on a flat surface in your vehicle, replace small plastic back with larger supplied plastic part and screw mount the PTT into desired location. 3. Plug the PTT pink connector end into the back of the Car Kit’s corresponding pink socket. Microphone Placement 1. Facing the microphone directly at the driver, mount the microphone on the sun visor or the headliner above. 2. Plug the microphones green connection end into the back of the Car Kit’s corresponding green socket. Carefully conceal cables to avoid any visual or physical hindrances. Optional Accessories (sold seperately) Gooseneck Microphone 1. Mount the microphone in the optimum location for the drivers use in the vehicle. (See your Gooseneck Microphone manual for detailed installation instructions.) 2. Plug the microphones connection end into microphone socket on the back of the car kit. (The Gooseneck Microphone optional accessory replaces the included car kit microphone.) Carefully conceal cables to avoid any visual or physical hindrances. (see pg. 3 for socket location) Palm Mic 1. Mount the palm mic bracket in the optimum location for the drivers use in the vehicle. (See your Palm Mic manual for detailed installation instructions.) 2. Plug the palm mic connection end into palm mic socket on the back of the car kit. (see pg. 3 for socket location) Foot Pedal 1. Mount the Foot Pedal in the optimum location for the drivers use in the vehicle. (See your Foot Pedal manual for detailed installation instructions.) 2. Plug the Foot Pedals connection end into Foot Pedals socket on the back of the car kit. (The Foot Pedal optional accessory replaces the car kits PTT button.) (see pg. 3 for socket location) Setup 1. Voltage range: 12-32V 2. Connection Method Green Cable – 12 VDC Constant - Power White Cable – Switched +12V DC - Ignition Black Cable – Ground Green Cable – Telephone Mute (Optional Install) 3. No Phone Inserted into the Car Kit Cradle • LED light will be active but will indicate that there is no phone being paired and connected. The LED will glow Red in this mode. • If you plug in a another device to the USB port at the front of the car kit, the output that it will provide is 5V/1A. • When the ignition is turned to Accessory mode, the car kit will stay active for 30 minutes. • During voice call if the ignition is turned to Accessory mode the car kit will stay acitve until the call is disconnected. 4. Bluetooth connection and pairing AUTO PAIRING If the handset is pairing for the first time 1. Enable auto-pairing in the phones Bluetooth settings. 2. Install the handset in the car kit, the handset Bluetooth will turn on automatically. 3. Search “Sonim Car Kit AVK01G” in handset. 4. Press “Sonim Car Kit AVK01G” in handset to pair. 5. After paired successfully, the LED will turn to green. If the handset had been paired before 1. Install the handset in the car kit, the handset Bluetooth will turn on automatically. 2. Press front button under LED to pair. 3. After paired successfully, the LED will turn to green. MANUAL PAIRING 1. Turn on Bluetooth from the phones settings. 2. Install the handset in the car kit. 3. Search “Sonim Car Kit AVK01G” in handset. 4. Press “Sonim Car Kit AVK01G” in handset to pair. 5. After paired successfully, the LED will turn to green. Functions Voice Call functionalities Answer call Short press PTT button <400ms Reject call Press and hold the PTT button for >400ms End call Short press PTT button Answer waiting call a. Short press PTT button. This will put the active call on hold and accept the waiting call b. Press and hold the PTT button for >400ms to End the active call and accept the waiting call Swapping between the held Short press PTT button and active calls Transferring the call audio Short press the ‘Bluetooth pairing button’ to transfer the audio from Bluetooth car kit speaker to phone earpiece and vice versa End Conference call Press and hold the PTT button for >400ms PTT Call functionalities Answer PTT Call Incoming PTT call will be automatically accepted Initiating PTT Call Short press PTT button (when the contact/group to be dialed is highlighted) PTT floor management On PTT call, press and hold the PTT button to take the floor and speak, release the held PTT button to release the floor End PTT call Please use the phone end button to end the PTT call Music functionalities Initiate music play Press the Bluetooth pairing button on the car kit Play/Pause during music play Press the Bluetooth pairing button on the car kit Audio Pick up sound in small mic Press small PTT button Pick up sound in palm mic Press PTT button on the palm mic Audio will always go through large speaker Regardless if palm mic or small PTT button is used Phone Inserted into the Car Kit Cradle (In Voice Call Mode Functionality) End Call Press any button Phone Inserted into the Car Kit Cradle (In PTT Call Mode Functionality) Generate only ‘button pressed’ and ‘button released’ events Just like pressing the PTT button on the device Receiving a voice call The receiving “Ring Alert” shall change the mode to voice call mode Ending the PTT call Must be performed from the phone not the car kit Additional functions Handset manages all call functions The car kit with short and long presses activate certain features in the handset but it is ultimately the handset that is managing all of these features Ignition in accessory mode The car kit will stay active for 30 minutes and will then only power off until there is no active call in progress. Warranty Sonim 1-year limited warranty Sonim provides a limited 1-year warranty for this accessory (hereinafter referred to as “Product”). Subject to the conditions of this limited 1-year Warranty Sonim warrants this product to be free from major defects in design, material and workmanship at the time of its original purchase by a consumer, and for a subsequent period of one (1) year. Conditions 1) This warranty does not cover any failure of the Product due to normal wear and tear, or due to misuse or abuse, including but not limited to use in other than the normal and customary manner, in accordance with the Sonim Product specifications and instructions for use and maintenance of the Product. Nor does this warranty cover any failure of the Product due to software or hardware modification or adjustment, acts of God or damage resulting from liquid interacting with the Product beyond what is described as acceptable in the user guide for the Product. 2) This warranty does not cover Product failures caused by installations, modifications, or repair or opening of the Product performed by any person other than a Sonimauthorized person. Tampering with any of the seals on the Product will void the warranty. 3) The warranty does not cover Product failures, which have been caused by use of other peripheral devices, which are not Sonim certified and intended for use with the Product. 4) THERE ARE NO EXPRESS WARRANTIES, WHETHER WRITTEN OR ORAL, OTHER THAN THIS PRINTED LIMITED WARRANTY. ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL SONIM OR ITS LICENSORS BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE WHATSOEVER, INCLUDING BUT NOT LIMITED TO LOST PROFITS OR COMMERCIAL LOSS; TO THE FULL EXTENT THOSE DAMAGES CAN BE DISCLAIMED BY LAW. For support or questions related to the warranty please visit www.sonimtech.com. Copyright © 2015 Sonim Technologies, Inc. SONIM and the Sonim logo are trademarks of Sonim Technologies, Inc. Other company and product names may be trademarks or registered trademarks of the respective owners with whom they are associated. Rev. A 5-20-15
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 5.6-c011 79.156289, 2014/03/31-23:39:12 Create Date : 2015:05:20 15:15:58-07:00 Metadata Date : 2015:05:20 15:16-07:00 Modify Date : 2015:05:20 15:16-07:00 Creator Tool : Adobe InDesign CC 2014 (Macintosh) Instance ID : uuid:065e77ce-cd7d-6e48-8333-fd97befd7b68 Original Document ID : xmp.did:73fe5d37-3cff-43fa-85a1-16f3bd273806 Document ID : xmp.id:df2c1ae7-2fa1-4ae3-a8b7-40dca1e985a7 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:ca6e07a5-ccb4-490e-b9b4-1cbd32ba38d0 Derived From Document ID : xmp.did:3865f304-bb7c-4133-b12f-532c3e5e6e2f Derived From Original Document ID: xmp.did:73fe5d37-3cff-43fa-85a1-16f3bd273806 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2014 (Macintosh) History Changed : / History When : 2015:05:20 15:15:58-07:00 Format : application/pdf Producer : Adobe PDF Library 11.0 Trapped : False Page Count : 10 Creator : Adobe InDesign CC 2014 (Macintosh)EXIF Metadata provided by EXIF.tools