Sony Group IJ1001SNBT Energy Storage System User Manual 1

Sony Corporation Energy Storage System 1

User Manual 1

User Manual1Sony Energy Devices Corporation2012.4Rev.5Energy Storage SystemMODEL : IJ1001SNBT
Energy Storage System “IJ1001SNBT”2FCC ComplianceThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuantto part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.This equipment complies with FCC radiation exprosure limits set forth for an uncontrolled environment andmeets the FCC radio frequency （RF）Exposure Guidelines in Supplement C to OET65. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation（MPE）. But it is desireable that it should be installed and operated keeping the radiotor at least 20cm or more away from person’s body（excluding extremities: hands, wrists, feet and ankles）.FCC WARNINGChanges or modifications not expressly approved by the party responsible for compliance could void user’sauthority to operate the equipment.Copyright Sony Energy Devices Corporation
Energy Storage System “IJ1001SNBT”3Table of ContentsImportant Safety InformationRead the firstSafety instructionsThe Energy Storage SysytemHow the system worksThe system structureThe Energy Storage System Installation Parts IncludedOther Parts and Tools RequiredInstall procedureOn site software update (if necessary)CommissioningThe Energy Storage System ActivationConnecting to the Internet.Activating Energy Storage System for Field Trial.Copyright Sony Energy Devices Corporation
Energy Storage System “IJ1001SNBT”4Important InformationRead the firstSAVE THESE INSTRUCTIONS– This manual contains important instructions for Model(s) IJ1001SNBT that shall be followed during installation and maintenance of the system.To reduce the risk of electrical shock, and to ensure the safe installation and operation of the Energy storage system, the following safety symbols appear throughout this document to indicate dangerous condition and important safety instructions.WARNING! This indicates a situation where failure to follow instructions may be a safetyhazard or cause equipment malfunction. Use extreme caution and followinstructions carefully.NOTE : This indicated information particularly important for optimal system operation.Follow instructions closely.Safety Instructions・Perform all electrical installations in accordance with all local electrical codes and the National Electrical Code（NFC）, ANSI/NFPA 70.・Be aware that only qualified personnel should install and/or replace the Energy storage system.・Do not attempt to repair the Energy storage system; it contains user-serviceable parts. If it fails,please contact Sony Customer service to obtain an product number and start the replacement process. Tampering with or opening the Energy storage system will void the warranty.・Before installing or using the Energy storage system, please read all instructions and cautionary markings in the technical description and on the Energy storage system.・Do NOT disconnect the Power cables from the Energy storage system without off the connection box.Copyright Sony Energy Devices Corporation
Energy Storage System “IJ1001SNBT”5The Energy storage systemThe Energy storage system is the world’s most technologically advanced energy storage system for utility-interactive applications. This manual details the safe installation and operation of the energy storage system.The three key elements of the Energy storage system are :・the energy storage system including Sony original lithium ion battery・the wireless communication system（WiFi）・the web-based monitoring and analysis systemThis integrated system maximizes energy efficiency, increases system reliability, and simplified design,installation and management.Copyright Sony Energy Devices CorporationPCSDistribution PanelConnection BoxPowermeterPVEnergy storage system
Energy Storage System “IJ1001SNBT”6The Energy Storage SystemHow the system WorksThis Energy storage system charges the integrated lithium ion battery from electrical utility gridthrough the distribution panel automatically when the battery’s capacity is not full and its charging period is controlled by the home energy management system（HEMS）which is specially by Sony Corporation.This Energy storage system outputs the electricity to electrical utility grid through the distributionpanel when determine the signal from HEMS. HEMS creates more efficiency control of the electrical power.To equalize the power demand to save the peak value so that the contract price is able to be saved andit’s benefit for the house owner.The system structureThis Energy storage system is integrated lithium ion battery, AC-DC converter and DC-AC inverters.General block diagram is bellow.Copyright Sony Energy Devices CorporationBatteryMicro ProcesserAC-DCConverterPowersensePowersenseGrid PowerIn/OutCircuitprotectorCircuitProtectorDC-ACInverterCircuitprotector
Energy Storage System “IJ1001SNBT”7The Energy Storage System InstallationFollow the instructions in this section to install the energy storage system.CAUTION : Before installing the energy storage system, read all instructions and cautionarymarkings in the installation manual.CAUTION : Perform all electrical installations in accordance with all local electrical codes and the National Electrical Code(NFC), ANSI/NFPA 70.CAUTION : Connect the energy storage system to the electrical utility grid only after receiving prior approval from the utility company.CAUTION : Be aware that only qualified personnel should must connect the energy storage system to the electrical utility grid.CAUTION : Be aware that installation of this equipment includes risk of electric shock.Normally grounded conductors may be undergrounded and energized whena ground fault is indicated.Parts IncludedIn addition to the energy storage system, battery module, you’ll need the system installation kit. This kit includes the following items :・Screws・Mounting Bracket・Antenna for WiFi module, Pipe and plastic case for Antenna. Copyright Sony Energy Devices Corporation
Energy Storage System “IJ1001SNBT”8Other Parts and Tools RequiredIn addition to the energy storage system and its associated hardware, you will need to provide thefollowings. The rating of the parts described on Page 50 to 54. Copyright Sony Energy Devices Corporation①Rail②Fixing bolt③Connection box④Connecter⑤Conduit pipe⑥Fixing parts①③④⑤ ⑥②
Energy Storage System “IJ1001SNBT”9Other Parts and Tools RequiredCopyright Sony Energy Devices Corporation①②③④⑤⑥⑦⑧⑨①Screw Driver（+）Φ6㎜(#2)②Screw Driver（+）Φ5㎜(#1)③Stabi. Driver（+）Φ6㎜(#2)④Nipper⑤Pench⑥Wire stripper⑦Hammer⑧Measure⑨Jig for removing the door
Energy Storage System “IJ1001SNBT”10Installation ProcedureInstalling the energy storage system involves several key steps :1, Open the cargo and Take out the energy storage server from outer enclosure.2, Open the energy storage server using screw driver and install the lithium ion battery module.3, Set the outer enclosure to the wall4, Install the energy storage server into the outer enclosure.5, Assemble the WiFi antenna to the outer enclosure.6, Set the connecting box and conduit＜Reference＞ScrewsCopyright Sony Energy Devices Corporation①② ③ ④⑤⑥⑦⑧①Low head screw（M3×8㎜）× 7pcs②Low head screw（M4×10㎜）× 2pcs③Screw （M4×10㎜）× 5pcs④Low head screw （M4×8㎜）× 8pcs⑤Screw （M4×8㎜Black）× 3pcs⑥Screw （M3×10㎜Black）× 12pcs⑦Screw （M3×8㎜Black）× 2pcs⑧Screw （M5×10㎜）× 6pcs
Energy Storage System “IJ1001SNBT”11Open the cargo and Take out the energy storage server from outer enclosureDescriptionCopyright Sony Energy Devices CorporationEnergy Storage SystemEnergy Storage ServerOuter EnclosureInverter
Energy Storage System “IJ1001SNBT”12Open the cargo and Take out the energy storage server from outer enclosureRemove the front door（Optional)Copyright Sony Energy Devices CorporationTool ⑨refer to Page 9Front door
Energy Storage System “IJ1001SNBT”13Open the cargo and Take out the energy storage server from outer enclosureRemove the belt.Copyright Sony Energy Devices CorporationIt won’t be used. Can be disposed.
Energy Storage System “IJ1001SNBT”14Open the cargo and Take out the energy storage server from outer enclosureRemove the jig-3.Copyright Sony Energy Devices CorporationJig-3The screw removed won’t be used.It can be disposed.
Energy Storage System “IJ1001SNBT”15Open the cargo and Take out the energy storage server from outer enclosureRemove the jig-4,5.Copyright Sony Energy Devices CorporationJig-4Jig-5The screw removed won’t be used.It can be disposed.
Energy Storage System “IJ1001SNBT”16Open the cargo and Take out the energy storage server from outer enclosureRemove the front panel of the energy storage server.Copyright Sony Energy Devices CorporationFront panel
Energy Storage System “IJ1001SNBT”17Open the cargo and Take out the energy storage server from outer enclosureRemove the cables bellow.Copyright Sony Energy Devices CorporationCompleted photo
Energy Storage System “IJ1001SNBT”18Open the cargo and Take out the energy storage server from outer enclosureRemove the wire from ground terminal on the rear panel of energy storage server.Copyright Sony Energy Devices CorporationGround terminal

Navigation menu