Sony Group IJ1001SNBT Energy Storage System User Manual 4

Sony Corporation Energy Storage System 4

User Manual 4

Energy Storage System “IJ1001SNBT”57Set the connecting box and conduitWiring 4 position bellow.Copyright Sony Energy Devices CorporationGrounding
Energy Storage System “IJ1001SNBT”58Set the connecting box and conduitTie the cables follow the bellow instruction and add some of magnetic core.Copyright Sony Energy Devices CorporationTie the cablesAdd the magnetic core provided by Sony
Energy Storage System “IJ1001SNBT”59Set the connecting box and conduitSet the front door then Completed.Copyright Sony Energy Devices Corporation
Energy Storage System “IJ1001SNBT”60Copyright Sony Energy Devices CorporationOn site software updateBecause of preinstalled software in factory, normally it is not required to install any software.But in some cases, software update may be required on site.On site software update procedure is as follows. 1.2.3. TBD
Energy Storage System “IJ1001SNBT”61Copyright Sony Energy Devices CorporationCommissioningCAUTION : Connect the energy storage system to the electrical utility grid only after receiving prior approval from the utility company.CAUTION : Be aware that only qualified personnel should must connect the energy storage system to the electrical utility grid.CAUTION : Ensure that all AC and DC wiring is correct. Ensure that none of the AC and DC wires are pinched or damaged. Ensure that all junction boxes are properly closed
The Energy Storage System ActivationConnecting to the Internet1. Confirm that there is a home router with wireless LAN working in the residence. 2. Connect with the home router using WPS.Please follow a procedure below. (as same as normal WPS operation)1. Turn ON the circuit protector located behind of the energy storage server.( RED ARROWS )2. Wait for booting the Energy Storage Server.3. Push WPS button on the home router.4. (Within 2 minutes) Push WPS button located behind of the energy storage server.( BLUE ARROW )※While WPS period, WiFi LED is blinking.After that, if WiFi LED stays turning ON, WLAN setting is successfully completed.If pattern of blinking is changed,there is some error on WPS.Please try again from step 1.(turn OFF Energy Storage Server once)62WiFi Charge Discharge
The Energy Storage System ActivationActivating Energy Storage System for Field Trial1. Turn ON the Energy Storage Server and wait for boot.2. Confirm that the Energy Storage System is already connected to the Internet. (WPS is already done)3. Access to the cloud server to register the Energy Storage System, using Installer Web Application.Installer Web Application is the same one for HEMS Gateway.Please follow a procedure below. (as same as one for HEMS Gateway)1. Login to the installer application. (need installer account and password)63Enter installer account and password.Then push “Login” button.
2. Input SI Setup ID.3. Confirm SI Setup ID.64Input SI Setup IDThen push OKIf SI Setup ID is correct,then push OK
4. Go to registration process of Energy Storage System (called “Battery” in this application).5. Scan barcode which is labeled on transparent acrylic board inside the outer enclosure.65Push “Register New Gateway”If there is no barcode scanner, you can input barcode directly.(080046xxxxxxxxxx) Then push “OK”
6. Confirm that Energy Storage System is powered on (called “Battery” in this application).66
7. After waiting for a while※, it is successfully registered.Confirm that Energy Storage System which is newly registered is listed in Registered Gatewaysand its status is online.※If Energy Storage System is already booted and ready, it is around 10-15 seconds.But if you supply power in step6, it takes around 5 minutes. 67
APPENDIX68
Energy Storage System “IJ1001SNBT”69Copyright Sony Energy Devices CorporationHow to Power ON/OFF the Energy Storage SystemPower ON : Turn ON the circuit protector located behind of the energy storage server inside the outer enclosure.Power OFF : Turn OFF the breakers
Energy Storage System “IJ1001SNBT”70Copyright Sony Energy Devices CorporationIndicator LEDsEnergy Storage ServerInverterThere are five inverters in the outer enclosure.Each inverter has a LED indicator at the center of side panel of one.WiFi Charge Discharge<Normal condition>WiFi Charge DischargeorWiFi Charge DischargeorStartup LED Operation (beginning of discharge):One minute after DC power is first applied to the inverter, six short green blinks indicate a successful inverter startup sequence. Six short red blinks after DC power is first applied to the inverter indicate a failure during inverter startup.Post-Startup LED Indications:Flashing Orange – Producing powerFlashing Red – Not producing powerGFDI Fault:A solid red status LED when DC power has been cycled, indicates the inverter has detected a ground fault (GFDI) error.

Navigation menu