Sony Group IJ1001SNBT Energy Storage System User Manual 3
Sony Corporation Energy Storage System 3
Contents
- 1. User Manual 2
- 2. User Manual 1
- 3. User Manual 3
- 4. User Manual 4
User Manual 3
Energy Storage System “IJ1001SNBT” Open the energy storage server using screw driver and install the lithium ion battery module Fixing the top cover. Insert the antenna cable Top cover Copyright Sony Energy Devices Corporation 38 Energy Storage System “IJ1001SNBT” Open the energy storage server using screw driver and install the lithium ion battery module Fixing the top cover. Rear Front Screw:⑥Screw(M4×10㎜ Black)×4pcs Copyright Sony Energy Devices Corporation 39 Energy Storage System “IJ1001SNBT” Set the outer enclosure to the wall 25.4㎜(1in) 177.8㎜(7in) Make a hole for conduit inside the bellow area. 25.4㎜(1in) Hole(1.06in) 304.8㎜(12in) Copyright Sony Energy Devices Corporation 40 Energy Storage System “IJ1001SNBT” Set the outer enclosure to the wall Fixing the outer enclosure to the wall 4 bolts. Bolt : For Wood Wall Diameter 3/8 inch Length : 3-1/4 inch For Concrete Diameter 3/8 inch Length 3 inch Keep the distance 30cm or more From the ground Ground Copyright Sony Energy Devices Corporation 41 Energy Storage System “IJ1001SNBT” Install the energy storage box into the outer enclosure Install the energy storage server to the outer enclosure. Install Copyright Sony Energy Devices Corporation 42 Energy Storage System “IJ1001SNBT” Install the energy storage box into the outer enclosure Wiring 8 position bellow. Completed photo Copyright Sony Energy Devices Corporation 43 Energy Storage System “IJ1001SNBT” Install the energy storage box into the outer enclosure Wiring ground terminal using the grounding cable from outer enclosure to the energy storage server. Ground terminal Completed photo Copyright Sony Energy Devices Corporation 44 Energy Storage System “IJ1001SNBT” Install the energy storage box into the outer enclosure Check the circuit protector. OFF OFF Confirm the circuit protector is off Copyright Sony Energy Devices Corporation 45 Energy Storage System “IJ1001SNBT” Install the energy storage box into the outer enclosure Insert the fuse bar. Fuse bar Screw:⑦Screw(M3×8㎜ Black)×2pcs Copyright Sony Energy Devices Corporation 46 Energy Storage System “IJ1001SNBT” Install the energy storage box into the outer enclosure Insert the front panel of the server. Front panel Copyright Sony Energy Devices Corporation 47 Energy Storage System “IJ1001SNBT” Install the energy storage box into the outer enclosure Fixing the jig-3. Jig-3 Screw:⑧Screw(M5×10㎜)×2pcs Copyright Sony Energy Devices Corporation 48 Energy Storage System “IJ1001SNBT” Install the energy storage box into the outer enclosure Fixing the jig-4,5. Completed photo Jig-5 Jig-4 Jig-4 Jig-5 Screw:⑧Screw(M5×10㎜)×4pcs Copyright Sony Energy Devices Corporation 49 Energy Storage System “IJ1001SNBT” Assemble the WiFi antenna to the outer enclosure Wear metal parts and fix the metal pipe. Antenna BOX CK-34Z U-0418-S1 Screw out Wear metal parts Antenna Metal connector Metal Pipe ※Insert the pipe then Insert antenna cable Completed lock the connector Copyright Sony Energy Devices Corporation 50 Energy Storage System “IJ1001SNBT” Assemble the WiFi antenna to the outer enclosure Fix the pipe to the outer enclosure. Outer Enclosure Connector and Pipe Connect screw Straight Liquid tight Connector 3/4" Trade Size Liquid tight Flexible Steel Conduit 3/4" Trade Size Copyright Sony Energy Devices Corporation 51 Energy Storage System “IJ1001SNBT” Assemble the WiFi antenna to the outer enclosure Connect to the antenna cable and fix the cable inside the outer enclosure. Cable from the antenna ※Insert the pipe then lock the connector Cable from the energy storage server Fixed using tie Completed Copyright Sony Energy Devices Corporation 52 Energy Storage System “IJ1001SNBT” Set the connecting box and conduit Overview Set the connecting box to the wall and conduit from the energy storage system and to distribution panel. Branch circuit inside the distribution panel required UL489 Listed, rated 240Vac, 30A, Time delay. 3 Cables are used, LI(Red) and N(White) connected to 120V, 60Hz. L2(Black) and N connected to 120V, 60Hz. Before start the installation, please refer to the next page. Connecting Box UL Listed, 30A L1 L2 GND AC120V, 60Hz Branch circuit UL489 Listed, 240V, 30A, Time delay AC120V, 60Hz Copyright Sony Energy Devices Corporation 53 Energy Storage System “IJ1001SNBT” Set the connecting box and conduit Remarks The field-wiring terminals shall be connected using the following wire types: AC connections: 18 in./lbs. - 22 in./lbs. tightening torque #10 AWG - #14 AWG wire type – rated 90C Copper Equipment Electrode Terminal: 75 in./lbs. – 88 in./lbs. tightening torque #8 AWG - #10 AWG wire type – rated 90C Copper Limits of accuracy of frequency measurement (+ 0.1 Hz) Limits of accuracy of Voltage measurement (+ 6 V) For conduit hubs, use only UL Listed rain tight for entry into the enclosure. AC output / neutral is not bonded to ground. The AC input and AC output circuits are isolated from the enclosure and that system grounding, if required by Section 250 of the National Electrical Code, ANSI/NFPA 70, is the responsibility of the installer. The National Electrical Code, ANSI/NFPA 70 wiring methods are to be used. use if needed The following pressure terminal connectors / component terminal assemblies are allowed / provided for field installation with this unit. Manufacturer : OSADA Co., Ltd (E121961) Model #Type : OK-147-3P Acceptable wire gauges : 16-10 AWG Copyright Sony Energy Devices Corporation 54 Energy Storage System “IJ1001SNBT” Set the connecting box and conduit Remarks This charge controller / inverter is intended to charge batteries of the following type 51.2V Li-ion type only. This inverter is intended for operation in an environment having a maximum ambient temperature of 60 degrees C. CAUTION To reduce the risk of fire, connect only to a circuit provided with 30 amperes maximum branch-circuit over current protection in accordance with the National Electrical Code, ANSI/NFPA 70. Units with an integral ground-fault detector/interrupter [JWC1] CAUTION Risk of electric shock. Normally grounded conductors may be ungrounded and energized when a ground-fault is indicated. Copyright Sony Energy Devices Corporation 55 Energy Storage System “IJ1001SNBT” Set the connecting box and conduit Conduit work. Wire from distribution panel Copyright Sony Energy Devices Corporation 56
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : 07665 Create Date : 2012:05:01 16:04:14+09:00 Modify Date : 2012:05:01 16:04:23+09:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2012:05:01 16:04:23+09:00 Creator Tool : PScript5.dll Version 5.2.2 Format : application/pdf Title : Microsoft PowerPoint - Energy_Storage_System_User_manual_Rev5_20120425.pptx Creator : 07665 Document ID : uuid:b18cb875-df86-4895-af4f-a642e3f939db Instance ID : uuid:300fd890-4fab-4821-bb48-36363a8d8737 Producer : Acrobat Distiller 9.3.3 (Windows) Page Count : 19EXIF Metadata provided by EXIF.tools