Spectrum 450202ZIG OHM Zigbee V.2 User Manual 912 ENG indd

Spectrum Brands, Inc. OHM Zigbee V.2 912 ENG indd

User Manual - 912

Q (2x)LLeversQRSTUAB slant of latch bolt faces door frame slant of latch bolt faces door frame62886 / 01ZigBeeInstallation and User GuideKwikset1-866-863-6584www.kwikset.comParts in the boxLatchStrikeKeysSpindleExterior AssemblyMounting PlateScrews and accessoriesSmartKey ToolInterior AssemblyIf drilling a new door, use the supplied template and the complete door drilling instructions available at www.kwikset.com/doorprep.backsetMeasure to conirm that the hole in the door is 21/8" (54 mm).*If you are installing this lever below an existing lock or you plan to install a lock above this lever, make sure that the distance between holes is at least 61/2" (165 mm). Measure to conirm that the backset is either 23/8" or 23/4" (60 or 70 mm).23/8" or 23/4"60 or 70 mmSee note below*13/8" – 13/4"35 – 44 mmMeasure to conirm that the hole in the door edge is 1" (25 mm).Measure to conirm that the door is between 13/8" and 13/4" (35 mm and 44 mm) thick.AABCDB C DAre the latch holes centered in the door hole?Is the door edge chiseled?Install strike on the door frame.Hold the latch in front of the door hole, with the latch face lush against the door edge.lush1"25 mmYES NONo adjustment is required. Proceed to next step.Move the pin to extend the latch.door frameENGLISH21/8"54 mmYES NOwood blockRequired toolsRuler4 AA BatteriesHammer Wood blockPhillips head screwdriverAdditional Tools (depending on application)1 / 4ABCDEFGHKLJMNPA / BABP (2x)“B” is not included. If needed, please contact Kwikset to order a drive-in latch for your lock.ororchiseled not chiseled1Prepare the door and check dimensions2Install the latch and strike
Install interior assembly onto mounting plate.Remove battery cover and battery pack from interior assembly.A Bacbabcd Ensure correct polarity. For best results, use new, non-rechargeable Alkaline batteries only.Install exterior keypad.keep parallel to edge of doortighten screws evenlyRemove battery cover. Connect cable.Install battery pack.Push interior assembly onto mounting plate.Secure with screws.Ensure tight cable connection.Push excess cable back into the door as you install E.Turnbut ton may need to be turned to install E.Install 4 AA batteries into battery pack.Remove battery pack.rounded edge faces latchlatchSecure interior lever.Route cable through mounting plate.Install exterior lever.Secure mounting plate with supplied screws.Secure exterior lever.Install spindle.Install interior lever.The small bolt of the latch should not enter the strike hole. If it enters the strike hole, reposition strike.AABBCCDDcable goes over latchDo not install battery pack into interior assembly yet.4xLever handle faces away from the latch.Tighten pre-installed set screw.If latch is loose in the strike, adjust the strike tab so it grips the latch bolt better when the door is closed.tabTighten pre-installed set screw.Lever handle faces away from the latch.Close door, test latch operation and make adjustments as needed:small bolt in strike holesmall bolt NOT in strike hole2 / 4FCDDM / N M / NR REGHU (2x)S (2x)3Install the exterior keypad, mounting plate, and spindle456Install interior assemblyInstall leversTest latch operation
1x 3x 2xgreen redRe-key the lock (if needed). Install the battery cover.Conirm that the code(s) added in step 8 can unlock the door.A BOne green lash with one beep* Three red lashes with three beeps* Two beeps*or orIMPORTANT: Remove battery pack before re-keying.Make sure the door is open. Press the Program button the number of times that corresponds to the user code position being programmed. Locking the Door Unlocking the DoorEnter user code. A total of 30 user codes may be programmed.Press Lock button once.A B CWhat lights and sounds does the lock produce?DEach user code must be a unique code between 4 and 8 digits, depending on your smart home system.Example: If programming the third code, press the button three times.Programming was successful. Programming was unsuccessful. Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt.Programming time out. Make sure not to pause for more than 5 seconds during programming.Press Lock button once. Enter user code.Tip: You can press the Lock button before entering your user code to light up the keypad at night.It is recommended that you add and delete all user codes through your smart home control system. If your system does not allow this, codes may be added directly to the lock as shown here.Programming Timeout If no button is pressed for 5 seconds, the system will time out and you will need to restart the procedure. *Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon. See “Switches and Status LED Colors” on page 4.MastercodeFor enhanced security, a mastercode may be used when adding and deleting user codes. For more information about the mastercode, download the Programming and Troubleshooting Guide on the SmartCode 912 page at www.kwikset.com.3 / 4DDCRJT (2x)a ab bcRe-key the lock to work with your existing key. See the supplied SmartKey Re-key instructions for more information. Reinstall battery pack.Keep “R” in a safe place, as you will need it to access the back panel for additional programming.8910Add user codes (30 max)Re-key the lock (if needed) and install the battery coverTest the lock (review normal operation)Initiate the pairing process at your smart home controller. Refer to your smart home system instructions for more information. When prompted by your smart home system to initiate pairing at the lock, press button “A” on the lock interior four times.If the pairing process is successful, re-name the lock in your system (if applicable).If the pairing process is unsuccessful, press button “B” nine times. Perform steps 7A7C again.If pairing is still unsuccessful, consult the Programming and Troubleshooting Guide on the SmartCode 912 page at www.kwikset.com.A B CDPair the lock with your smart home system7“A” “B”
© 2015 Spectrum Brands, Inc.1. Read all instructions in their entirety.2. Familiarize yourself with all warning and caution statements.3. Remind all family members of safety precautions.4. Protect your user codes and mastercode.5. Dispose of used batteries according to local laws and regulations. CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes, you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge. The use of a mastercode can help protect your system’s settings. WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualiied locksmith or other security professional.Network Information Important SafeguardsAlert Reason SolutionKeypad lashes red 1 time with 1 beep*Door jammed while attempting to lock.Manually re-lock door. If needed, reposition strike.Keypad lashes red 3 times with 3 beeps*Unsuccessful programming. Attempt programming procedure again.One incorrect code entered. Re-enter code.No user code programmed. Program at least one user code.Keypad lashes red 10 times with 10 beeps* Low battery. Replace batteries.Lock beeps 2 times.Programming timeout.Attempt programming procedure again, making sure not to pause for more than 5 seconds.Keypad lashes red 3 times.Keypad lashes red 6 times with 6 beeps*.Keypad lashes red 15 times with 15 beeps*Three incorrect codes entered within one minute.Re-enter code after 60 second keypad lockout.Adding the lock to the networkDuring the pairing process, press button “A” on the lock interior four times.Removing the lock from the networkPress button “B” on the lock interior nine time.ZigBee System NotesZigBee is a “Wireless mesh network,” and results may vary based on building construction and communication path, with 35+ feet being typical installed distance in a standard home environment and 250 feet+ when the lock has a clear line of sight with the smart home controller. It may be necessary to install additional ZigBee devices to enhance the communication path between the lock and controller for a more robust ZigBee network.SmartCode at a GlanceDeleting a user codeIn order to delete a user code, you must override the code by adding a di erent user code in the same position. For example, if you want to delete the third code, add a di erent user code in position three. Test the old user code to make sure it can no longer unlock the door.If you cannot remember the user code position, you may wish to perform a factory reset to delete all codes associated with the lock.Reference GuideExteriorBack panelProgram buttonStatus LEDSwitchesTurnpieceInterior (cover removed)Switches and Status LED colorsTroubleshootingSwitch Function1Door lock status LED blinks every 6 seconds2Lock automatically re-locks door 30 seconds after unlocking. Disabled if no codes are programmed.3 Audio4 Not used.Color Lock StatusGreen UnlockedAmber LockedRed Low battery1 2 3 4OnSwitchesStatus LEDO System AlertsFactory ResetBattery ReplacementA factory reset will delete all codes associated with the lock, and it will remove it from your smart home system.If another lock is installed above the lever, remove the interior assembly when battery replacement is required.Status LED1 Remove battery pack.2 Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED lashes red.KeypadLock buttonKeywaySmartKey tool holeButton “A” Button “B”3 Press the Program button once more. When the LED lashes green and you hear one beep, the lock has been reset.4 Pair the lock with your smart home system, and add user codes to your lock. A complete Programming and Troubleshooting Guide is available on the SmartCode 912 page at www.kwikset.com.Lock above leverMounting plateInterior assemblyBattery pack*Beeping sound will only be heard if switch #3 is on.4 / 4

Navigation menu