Spectrum 450202ZIG OHM Zigbee V.2 User Manual Kwikset Convert ZigBee indd

Spectrum Brands, Inc. OHM Zigbee V.2 Kwikset Convert ZigBee indd

User Manual

123Begin with your smart home appIf you will be using a smart home app with your lock, download the app and set up your controller or hub before proceeding further with lock installation.1 / 466492001 Rev 02914CZigBee Installation and User GuideENGLISHKwikset Technical Support1-866-863-6584www.kwikset.comTools neededExisting keyPhillips head screwdriverRulerOptional: Masking tapePrepare your doorDetermine the parts needed for your doorParts in the boxKit "A" Kit "B" Kit "C"Mounting plate screwsMounting plate screwsMounting plate screwsBlack mounting plateInterior coverInterior assemblyBattery pack and 4 AA batteriesSilver mounting plateGold mounting plateBlack adapterGold adapterGold adapterBlack adapterSilver adapterInterior assembly screwsInterior assembly screwsInterior assembly screwsInterior cover screwsInterior cover screwsInterior cover screwsMake sure your existing deadbolt is compatible. If you have a standard deadbolt mounted separately from the handle below it, it is compatible with Kwikset Convert. Make sure your door is aligned before proceeding with installation. A BLook into the hole in your door.What shape is your torque blade (the part sticking out through the latch)?For a list of compatible deadbolt models, please see the Kwikset Convert page at www.kwikset.comMortise LockNot CompatibleNot CompatibleRim LockIntegrated InteriorNot CompatibleCompatibleD-shapeKwikset and Weiser deadbolts:Use kit “A” for your door.Baldwin Reserve and Baldwin Prestige deadbolts:Use kit “B” for your door. You will need the black adapter and the thicker gold screws.thickerscrewsVertical rectangleBaldwin Estate deadbolts:Use kit “B” for your door.You will need the gold adapter and the thinner gold screws.thinnerscrewsSlanted rectangleSchlage deadbolts: Use kit “C” for your door.You will need the silver adapter.Horizontal rectangleSchlage deadbolts: Use kit “C” for your door.You will need the gold adapter.Make sure your door is open and extend your latch bolt. Make sure your key is NOT in the deadbolt exterior.extendedRemove all existing deadbolt hardware from the interior side of your door. DOptional: Secure your deadbolt exterior with masking tape.EMeasure to conirm that your door is either 13/8" or 13/4" (35 mm or 44 mm) thick.13/8"or 13/4"35 or 44 mmC FYou should be able to lock and unlock your door smoothly without any resistance, and without pushing, pulling or lifting your door.If your door is not aligned, you may need to order a Warped Door Service Kit, available through Kwikset Support:18668636584
2 / 44Install the mounting plate and test your latchtorque bladeNote: A D-shaped torque blade is shown, but installation is the same for all models.AC DPlace the mounting plate on the door so that the torque blade inserts through the center hole.Kwikset & Weiser Only: To determine which mounting screws to use, test one of the thicker screws irst. If the thicker screw its, continue installing the thicker screws.If the thicker screw doesn't it, install the thinner screws.Remove the masking tape from the exterior deadbolt, and insert your key and test the latch for smooth operation.Remove your key and make sure the bolt is fully extended.fully extendedIf the latch does not extend or retract smoothly, adjust the mounting screws.BKeep parallel to the edge of the door.Tighten screws evenly.Secure the mounting plate with the mounting screws.5Install the interior assemblyDSecure with two (2) interior assembly screws.bottom holeRemove the interior cover and battery pack.Aalign tabsGold adapter:Keep slot vertical.Press adapter irmly onto the interior assembly.Install the adapter on the interior assembly.back view of interior assemblyBSilver adapter:Tab is on bottom.Black adapter:Curve is on top.ab dMake sure the turnpiece is in the vertical position.Remove the interior cover.Remove the battery pack.Do not install batteries yet.verticalcMake sure shaft is oriented as shown. If needed, rotate the shaft to this position.Stripe should be vertical.CAlign the adapter with the torque blade and push the interior assembly onto the mounting plate.Schlage Deadbolts Only:You may need to rotate the adapter to align with the torque blade.actual size
3 / 4Pair the lock with your smart home systemwindowIf you wish to unlock the window, you can slide it up for more convenient access to the programming buttons while the cover is installed.To unlock the window, remove the security screw.The window on the interior cover is locked by default to prevent someone from tampering with your lock's settings.Important Information about the interior coverCover Installation:Install cover.Note: You may need to rotate the turnpiece to align with the turnpiece shaft.turnpiece shaftInstall screws.abInstall the interior coverInitiate the pairing process through your smart home system (either through your smart home app, at your panel, or at your controller or hub). Refer to your smart home system instructions for more information.When prompted by your smart home system to initiate pairing at the lock, press button “A” on the lock interior four times.If successful, re-name the lock in your system (if applicable).If unsuccessful, press button “B” nine times. Perform steps 8A8C again.If still unsuccessful, follow your smart home system's instructions to remove (exclude/unpair) the lock from any other network. Then perform steps 8A8C again.A B CDbutton “A” button “B”Note: The interior cover and screws must be removed for battery pack access.actual sizeConirm the lock statusPerform the door handing process6789The Status LED blinks every six seconds to communicate whether the door is locked or unlocked.If the Status LED is displaying the wrong lock status, lip switch #4.A BAmber: LockedGreen: UnlockedSwitch #4This step will teach the lock the orientation of your door and is crucial for lock operation.A B C DInstall 4 AA batteries in the battery pack. Ensure correct polarity. For best results, use new, non-rechargeable Alkaline batteries only.Make sure the door is open. Insert the battery pack while PRESSING AND HOLDING the Program button. Keep pressing the button for three seconds after the battery pack is installed, then release the button.The Status LED will lash red and green, and the lock will beep. Press and release the Program button again. The latch bolt will retract and extend on its own to learn the orientation of the door. Did the Status LED turn green or red?If the bolt does not move, make sure the batteries are installed correctly, and perform steps 6A6D again.status LEDMetal contacts at bottom, facing out.BALDWIN ESTATE DEADBOLTS:If your latch bolt is to the RIGHT of your interior assembly, and the Status LED is solid red after door handing, press and release the Program button again. The door handing process will restart.If you are unsure if your lock is Baldwin Estate, see chart on page 1 or compatible deadbolt list online.Red Status LEDGreen: Door handing successful. Continue to step 7.Red: See “Red Status LED” below. RightOTHER DEADBOLTS:If the Status LED is solid red after door handing, make sure the batteries are installed correctly and the lock interior is correctly installed. Perform steps 6A6D again.
4 / 4 © 2017 Spectrum Brands, Inc.Reference GuideFactory ResetA factory reset will remove your lock from your smart home system.Status LED1 Remove battery pack.2 Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED lashes red.3 Press the Program button once more. When the LED lashes green and you hear two beeps, the lock has been reset.4 Perform the door handing process again to teach the lock the orientation of the door and pair the lock to your smarthome system.1. Read all instructions in their entirety.2. Familiarize yourself with all warning and caution statements.3. Remind all family members of safety precautions.4. Always have access to your lock’s standard key.5. If using the Auto-Lock feature, make sure to have your standard key with you to prevent locking yourself out.6. Replace low batteries immediately. CAUTION: Prevent unauthorized entry. Restrict access to your lock’s back panel and routinely check your settings to ensure they have not been altered without your knowledge. WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualiied locksmith or other security professional.Important SafeguardsKwikset Convert at a GlanceABButton “A”Back panelProgram buttonTurnpiece shaftSwitchesButton “B”Status LEDSwitches1. Status LEDDoor lock status LED blinks every 6 seconds. ON position is factory default.2. Auto-Lock Automatically re-locks door 30 seconds after unlocking. OFF position is factory default. CAUTION: With this feature enabled, it is possible to lock yourself outside.3. AudioBeeping sound is heard during programming and normal operation. ON position is factory default.4. Invert Only used if the Status LED is communicating the opposite door lock status.on o 1234Status LED NotiicationsAmber lashDoor is lockedGreen lashDoor is unlocked.Red lashThe 4 AA batteries in the interior are low and need to be replaced.Network InformationZigBee System NotesZigBee is a “Wireless mesh network,” and results may vary based on building construction and communication path, with 35+ feet being typical installed distance in a standard home environment and 250 feet+ when the lock has a clear line of sight with the smart home controller or hub. It may be necessary to install additional ZigBee devices to enhance the communication path between the lock and controller/hub for a more robust ZigBee network.Removing the lock from the networkPress button “B” on the lock interior nine times.These features can be adjusted in some smart home apps.

Navigation menu