Spectrum 450202ZIG OHM Zigbee V.2 User Manual 912 ENG indd

Download:
Mirror Download [FCC.gov]
Document ID	3536665
Application ID	LglA795gwcWeBGtGL6YyFg==
Document Description	User Manual - 912
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	280.88kB (3511017 bits)
Date Submitted	2017-08-30 00:00:00
Date Available	2017-08-31 00:00:00
Creation Date	2015-04-30 10:18:47
Producing Software	Acrobat Distiller 10.1.13 (Windows)
Document Lastmod	2015-04-30 10:18:47
Document Title	912 ENG.indd
Document Creator	PScript5.dll Version 5.2.2
Document Author:	SAD0418

62886 / 01
ZigBee
Parts in the box
ENGLISH
Latch
Levers
Exterior
Assembly
Installation and User Guide
“B” is not included. If needed,
please contact Kwikset to order
a drive-in latch for your lock.
Interior
Assembly
Required tools
Mounting
Plate
Ruler
Kwikset
1-866-863-6584
www.kwikset.com
Phillips head screwdriver
Additional Tools (depending on application)
Hammer
Spindle
SmartKey
Tool
Keys
Strike
4 AA Batteries
Screws and accessories
Wood block
Prepare the door and check dimensions
If drilling a new door, use the supplied template and the complete
door drilling instructions available at www.kwikset.com/doorprep.
Measure to confirm that the hole in
the door is 2-1/8" (54 mm).
Measure to confirm that the backset is
either 2-3/8" or 2-3/4" (60 or 70 mm).
2-3/8" or 2-3/4"
60 or 70 mm
See
note
below*
ba
ck
se
Measure to confirm that the hole in
the door edge is 1" (25 mm).
Measure to confirm that the door
is between 1-3/8" and 1-3/4" (35 mm
and 44 mm) thick.
1-3/8" – 1-3/4"
35 – 44 mm
1"
25 mm
2-1/8"
54 mm
*If you are installing this lever below
an existing lock or you plan to install a
lock above this lever, make sure that the
distance between holes is at least 6-1/2"
(165 mm).
Install the latch and strike
Hold the latch in front of the door hole, with the
latch face flush against the door edge.
Is the door edge chiseled?
YES
NO
or
chiseled
not
chiseled
flush
slant of latch bolt faces
door frame
slant of latch bolt faces
door frame
Are the latch holes centered in the door hole?
YES
NO
or
P (2x)
wood block
No adjustment is required.
Proceed to next step.
Move the pin to extend the latch.
Install strike on the door frame.
A/B
Q (2x)
door frame
1/4
3
Install the exterior keypad, mounting plate, and spindle
Install exterior keypad.
Route cable through mounting plate.
Secure mounting plate with
supplied screws.
keep parallel to
edge of door
cable goes
over latch
Install spindle.
rounded edge
faces latch
U (2x)
tighten
screws
evenly
latch
Install interior assembly
Remove battery cover and battery pack from interior assembly.
Remove battery cover.
Remove
battery
pack.
Install interior assembly onto mounting plate.
Connect cable.
Ensure tight cable connection.
Install 4 AA batteries into battery pack.
Install
battery
pack.
4x
Ensure correct polarity.
For best results, use
new, non-rechargeable
Alkaline batteries only.
Do not install
battery pack
into interior
assembly yet.
Secure with
screws.
Push excess
cable back into
the door as you
install E.
S (2x)
Turnbutton
may need to
be turned to
install E.
Install levers
Install interior lever.
Secure interior lever.
Lever handle
faces away
from the latch.
M/N
Push interior assembly onto
mounting plate.
Install exterior lever.
Secure exterior lever.
Lever handle
faces away
from the latch.
Tighten preinstalled set
screw.
M/N
Test latch operation
Close door, test latch operation and make adjustments as needed:
If latch is loose in the strike, adjust the strike tab so it
grips the latch bolt better when the door is closed.
The small bolt of the latch should not enter the strike
hole. If it enters the strike hole, reposition strike.
small bolt in
strike hole
tab
small bolt NOT
in strike hole
2/4
Tighten preinstalled set
screw.
Pair the lock with your smart home system
Initiate the pairing process at your smart
home controller. Refer to your smart home
system instructions for more information.
When prompted by your smart home
system to initiate pairing at the lock, press
button “A” on the lock interior four times.
“A”
“B”
If the pairing process is successful, re-name
the lock in your system (if applicable).
If the pairing process is unsuccessful, press button “B”
nine times.
Perform steps 7A-7C again.
If pairing is still unsuccessful, consult the
Programming and Troubleshooting Guide on the
SmartCode 912 page at www.kwikset.com.
Add user codes (30 max)
It is recommended that you add and
delete all user codes through your smart
home control system. If your system
does not allow this, codes may be added
directly to the lock as shown here.
Make sure the door is open. Press
the Program button the number of
times that corresponds to the user
code position being programmed.
Programming Timeout
If no button is pressed for 5 seconds, the
system will time out and you will need to
restart the procedure.
Example: If
programming
the third code,
press the button
three times.
Enter user code. A total of 30 user
codes may be programmed.
Press Lock button once.
Each user code must
be a unique code
between 4 and 8 digits,
depending on your
smart home system.
What lights and sounds does the lock produce?
One green flash with one beep*
Three red flashes with three beeps*
Two beeps*
or
or
1x
green
3x
red
2x
Programming was unsuccessful.
Programming time out.
Make sure the user code is not a duplicate and that it is
between 4 and 8 digits during your next attempt.
Make sure not to pause for more than 5
seconds during programming.
Programming was successful.
*Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon. See “Switches and Status LED Colors” on page 4.
Mastercode
For enhanced security, a mastercode may be used when adding and deleting user codes. For more information about the mastercode, download the Programming
and Troubleshooting Guide on the SmartCode 912 page at www.kwikset.com.
Test the lock (review normal operation)
Confirm that the code(s) added in step 8 can unlock the door.
Locking the Door
Unlocking the Door
Press Lock button once.
Enter user code.
Tip: You can press the
Lock button before
entering your user
code to light up the
keypad at night.
10
Re-key the lock (if needed) and install the battery cover
Re-key the lock (if needed).
IMPORTANT:
Remove battery
pack before
re-keying.
Re-key the lock to work with your
existing key. See the supplied
SmartKey Re-key instructions
for more information.
Reinstall
battery
pack.
Install the battery cover.
T (2x)
Keep “R” in a safe place, as you will need it to
access the back panel for additional programming.
3/4
Reference Guide
SmartCode at a Glance
System Alerts
Exterior
Alert
Reason
Solution
Keypad flashes red 1 time
with 1 beep*
Door jammed while
attempting to lock.
Manually re-lock door. If needed,
reposition strike.
Unsuccessful programming.
Attempt programming procedure
again.
One incorrect code entered.
Re-enter code.
No user code programmed.
Program at least one user code.
Low battery.
Replace batteries.
Programming timeout.
Attempt programming procedure
again, making sure not to pause for
more than 5 seconds.
Three incorrect codes entered
within one minute.
Re-enter code after 60 second keypad
lockout.
Interior (cover removed)
Keypad flashes red 3 times
with 3 beeps*
Button “A”
Button “B”
Back
panel
Keypad flashes red 10
times with 10 beeps*
Program
button
Keypad
Lock
button
SmartKey
tool hole
Lock beeps 2 times.
Switches
Status
LED
Keypad flashes red 3 times.
Keypad flashes red 6 times
with 6 beeps*.
Turnpiece
Keyway
Keypad flashes red 15 times
with 15 beeps*
*Beeping sound will only be heard if switch #3 is on.
Switches and Status LED colors
Deleting a user code
Switches
In order to delete a user code, you must override the code by adding a different user code in the same
position. For example, if you want to delete the third code, add a different user code in position three.
On Off
Status
LED
Test the old user code to make sure it can no longer unlock the door.
If you cannot remember the user code position, you may wish to perform a factory reset to delete all
codes associated with the lock.
1 2 3 4
Switch
Function
Color
Lock Status
Door lock status LED blinks every 6
seconds
Green
Unlocked
Lock automatically re-locks door 30
seconds after unlocking. Disabled if no
codes are programmed.
Amber
Locked
Red
Low battery
Audio
Not used.
Troubleshooting
A complete Programming and Troubleshooting Guide is
available on the SmartCode 912 page at www.kwikset.com.
Battery Replacement
Factory Reset
If another lock is installed above the lever, remove the interior
assembly when battery replacement is required.
A factory reset will delete all codes associated with the lock,
and it will remove it from your smart home system.
1 Remove
battery pack.
Lock
above
lever
2 Press and HOLD the Program
button while reinserting
the battery pack.
Keep holding the button for 30
seconds until the lock beeps
and the status LED flashes red.
Status
LED
Battery
pack
3 Press the Program button
once more. When the LED
flashes green and you
hear one beep, the lock
has been reset.
Interior
assembly
Mounting
plate
Network Information
4 Pair the lock with your smart home
system, and add user codes to your lock.
Important Safeguards
ZigBee System Notes
1.
2.
3.
4.
5.
ZigBee is a “Wireless mesh network,” and results may vary based on building construction and
communication path, with 35+ feet being typical installed distance in a standard home environment and
250 feet+ when the lock has a clear line of sight with the smart home controller. It may be necessary to
install additional ZigBee devices to enhance the communication path between the lock and controller for a
more robust ZigBee network.
Adding the lock to the network
Removing the lock from the network
During the pairing process, press button “A” on the
lock interior four times.
Press button “B” on the lock interior nine time.
Read all instructions in their entirety.
Familiarize yourself with all warning and caution statements.
Remind all family members of safety precautions.
Protect your user codes and mastercode.
Dispose of used batteries according to local laws and regulations.
CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel
can change the user codes, you must restrict access to the back panel and routinely
check the user codes to ensure they have not been altered without your knowledge.
The use of a mastercode can help protect your system’s settings.
WARNING: This Manufacturer advises that no lock can provide complete security
by itself. This lock may be defeated by forcible or technical means, or evaded by
entry elsewhere on the property. No lock can substitute for caution, awareness of
your environment, and common sense. Builder’s hardware is available in multiple
performance grades to suit the application. In order to enhance security and reduce
risk, you should consult a qualified locksmith or other security professional.
4/4
© 2015 Spectrum Brands, Inc.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : SAD0418
Create Date                     : 2015:04:30 10:18:47-07:00
Modify Date                     : 2015:04:30 10:18:47-07:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : 912 ENG.indd
Creator                         : SAD0418
Producer                        : Acrobat Distiller 10.1.13 (Windows)
Document ID                     : uuid:17812e47-5155-4a6e-8530-cebd95d7ebda
Instance ID                     : uuid:8866e966-2f6c-4f51-add9-201120a058e7
Page Count                      : 4

EXIF Metadata provided by EXIF.tools