Spectrum 450202ZIG OHM Zigbee V.2 User Manual Item 8 Users Manual 5066863 914

Spectrum Brands, Inc. OHM Zigbee V.2 Item 8 Users Manual 5066863 914

User Manual - 914

1 / 4Begin with your smart home appIf you will be using a smart home app with your lock, download the app and set up your controller or hub before proceeding further with lock installation.AN (2x)AABBBABIf drilling a new door, use the supplied template and the complete door drilling instructions available at kwikset.com/doorprep13/8" –2"35 – 51 mmA BCDIs the door edge chiseled?Is the D-shaped hole centered in the door hole?Which latch are you installing?Hold the latch in front of the door hole, with the latch face lush against the door edge.1"25 mmYESYESNONOUse latch “A”. If the latch bolt is not already extended, extend the latch bolt as shown.No adjustment is required. Proceed to next step.D-shaped hole D-shaped holeRotate latch face as shown to extend latch.UP is on top.UP is on top.wood blockUse latch “B” (not included). If the latch bolt is not already extended, extend the latch bolt as shown.Latch “A” Latch “B”door frameEInstall the strike on the door frame. Make sure the hole in the door frame is drilled a minimum of 1" (25 mm) deep.orchiseled not chiseledor123Prepare the door and check dimensionsInstall the latch and strikeor23/8" or 23/4"60 or 70 mmbacksetMeasure to conirm that the backset is either 23/8" or 23/4" (60 or 70 mm).Measure to conirm that the hole in the door edge is 1" (25 mm).Measure to conirm that the door is between 13/8" and 2" (35 mm and 51 mm) thick.Remove your existing deadbolt from your door.C D E FBLatch“B” is not included. If needed, please contact Kwikset to order a drive-in latch for your lock.StrikeCKeysE A BExterior AssemblyAdapter Ring DMounting PlateParts ListFastenersInterior AssemblySmartKey ToolHMFKLGMeasure to conirm that the hole in the door is either 21/8" (54 mm) or 11/2" (38 mm).or21/8"54 mm11/2"38 mmNote: Additional door preparation may be required for doors with 11/2" (38 mm) holes. Consult the deadbolt drilling instructions at kwikset.com/doorprepAMake sure your door is compatible. If you have a standard deadbolt mounted separately from the handle below it, your door is compatible.Mortise LockNot CompatibleNot CompatibleRim LockCompatible Not CompatibleIntegrated Interior03809 46780 N Q SP48654 64109 T V49191 US (2x) CQ (2x)Longer screws install closest to the door jamb.N P SQactual size66863001 Rev 02ZigBeeInstallation and User GuideKwikset1-866-863-6584www.kwikset.comBatteriesENGLISHRequired toolsRulerHammer Wood block ChiselPhillips head screwdriverAdditional Tools (depending on application)W
2 / 421/8"54 mm11/2"38 mm KWactual sizeT KGreen: Door handing was successful. Proceed to next step.Red: Door handing was unsuccessful. Make sure the lock interior and batteries are correctly installed. Perform step 6B again.If the bolt does not move, make sure the batteries are correctly installed, and perform step 6B again.What is the diameter of the hole in the door?Install 4 AA batteries in the battery pack. With the door open, press and HOLD the Lock button while installing the battery pack.Hold the button until the latch bolt starts moving on its own.The latch will retract and extend to learn the orientation of the door.The Status LED will indicate success or failure.Locate the screws for step 4C and keep them within reach. Install the exterior keypad and mounting plate.AA B CDBCDiameter is 21/8" (54 mm)Diameter is 11/2"(38 mm)or“D” is required for installation. Install “D” on “F”.“D” is not needed for installation. Discard “D”. The cable goes underneath the latch. Support the exterior assembly during mounting plate installation.Route the cable through the center hole, then push it into the bottom hole. Insert the key and test the latch. If the latch does not extend or retract smoothly, adjust the screws (T). Remove the key when inished, and make sure the latch bolt is fully extended.Keep parallel to the edge of the door.Tighten screws evenly.acbdNote: The latch bolt will only retract half way. Ensure correct polarity. For best results, use new, non-rechargeable Alkaline batteries only.Uactual size U(2x)Remove the interior cover and battery pack from the interior assembly. Install the interior assembly onto the mounting plate.A BacbdMake sure the turnpiece is in the vertical position.Make sure turnpiece shaft is rotated as shown.Do not install batteries until step 6.Ensure tight cable connection.Lay the excess cable lat inside the bottom of the interior housing.alignLacbdbottom holeM LLLKDDFFGTT (2x)TE4Install the exterior keypad5Install the interior assembly6Install the batteries and perform the door handing processThis step will teach your lock the orientation of your door and is crucial to lock operation.
3 / 41xgreen3xredInitiate the pairing process through your smart home system (either through your smart home app, at your panel, or at your controller or hub). Refer to your smart home system instructions for more information. When prompted by your smart home system to initiate pairing at the lock, press button “A” on the lock interior four times.If the pairing process is successful, re-name the lock in your system (if applicable).If the pairing process is unsuccessful, press button “B” nine times. Perform steps 7A7C again.If still unsuccessful, follow your smart home system's instructions to remove (exclude/unpair) the lock from any other network. Then perform steps 7A7C again.A B CDPair the lock with your smart home systembutton “A” button “B”Install the battery cover.MV (3x)abIMPORTANT: Remove battery pack before re-keying.KHKabcRe-key the lock to work with your existing key. See the supplied SmartKey Re-key instructions for more information.Reinstall battery pack.Optional: Re-key the lock.A BIt is recommended that you add and delete all user codes through your smart home system. If your system does not allow this, codes may be added directly to the lock as shown here.One green lash with one beep Three red lashes with three beepsorMake sure the door is open. Press the Program button once.BPress the Lock button once.DWhat lights and sounds does the lock produce?EEnter a new user code. A total of 30 user codes may be programmed.CEach user code must be a unique code between 4 and 8 digits, depending on your smart home system.Programming was successful. Programming was unsuccessful. *Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon.Programming informationMastercode: For enhanced security, a mastercode may be used when adding and deleting user codes. For more information about the mastercode, download the SmartCode 914 Programming and Troubleshooting Guide at www.kwikset.com.Programming Timeout: During programming, if no button is pressed for ive seconds, the system will time out (indicated by three beeps and a red lashing keypad), and you will need to restart the procedure.With the door open, press the Lock button. Conirm that the door locks.Enter the user code(s) added in the previous step. Conirm that the door unlocks.Close the door. Press the Lock button. Conirm that the door locks smoothly without error.If your does not lock smoothly, make sure you replaced your previous latch and strike with those supplied in the box.If you still experience locking errors, call Kwikset Support to order a Warped Door Service Kit.Kwikset Support: 18668636584AA B C DMove swiftly through programming, as the system will time out if no button is pressed for ive seconds.Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt.Make sure the lock has room for an additional code. If all user code positions are illed, delete a code to make room for this one.Vactual size78910Add user codes (30 maximum)Re-key the lock (if needed) and install the battery coverTest the lock and check door alignment
Alert Reason SolutionKeypad lashes red once with one beep*. One incorrect code entered. Re-enter code.Keypad lashes red three times with three beeps*.No user code programmed. Program at least one user code.Programming timeout after ive seconds. Attempt programming procedure again.Unsuccessful programming.Keypad lashes red 15 times with 15 beeps*Three incorrect codes entered within one minute.Re-enter code after 60 second keypad lockout.Keypad lashes red with fast beeping sound for three to four seconds.Low battery. Replace batteries.Keypad lashes red with continuous beeping sound for two seconds.Door jammed while attempting to lock.Manually re-lock door. If needed, reposition strike.Lock beeps continuously. Interior assembly is disconnected from exterior.Remove battery pack, reconnect the interior to the exterior, then reinstall battery pack.*Beeping sound will only be heard if switch #3 is on.4 / 4Removing the lock from the networkPress button “B” on the lock interior nine times.© 2017 Spectrum Brands, Inc.1. Read all instructions in their entirety.2. Familiarize yourself with all warning and caution statements.3. Remind all family members of safety precautions.4. Protect your user codes and mastercode.5. Dispose of used batteries according to local laws and regulations. CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes, you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge. The use of a mastercode can help protect your system’s settings. WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualiied locksmith or other security professional.Network Information Important SafeguardsZigBee System NotesZigBee is a “Wireless mesh network,” and results may vary based on building construction and communication path, with 35+ feet being typical installed distance in a standard home environment and 250 feet+ when the lock has a clear line of sight with the smart home controller or hub. It may be necessary to install additional ZigBee devices to enhance the communication path between the lock and controller/hub for a more robust ZigBee network.If no button is pressed for ive seconds, the system will time out, and you will need to restart the procedure.1 Keep door open. Press Program button once.5 Re-enter user code. 6 Press Lock button once. If unsuccessfulMake sure to enter the same valid code in steps 3 and 5. Test codeWhile the door is open, test the user code to make sure it no longer unlocks the door.2 Press Lock button once.4 Press Lock button once.3 Enter user code to be deleted.SmartCode at a GlanceDeleting a single user code (manually at the lock)Note: All codes may be deleted at once if the mastercode is enabled. For more information about the mastercode, consult the SmartCode 914 Programming and Troubleshooting Guide at www.kwikset.com.Reference GuideExteriorBack panelProgram buttonStatus LEDSwitchesTurnpiece shaftNote: When the cover is removed, the turnpiece shaft can be used to manually lock and unlock the door.These features can be adjusted in some smart home apps.Interior (cover removed)Switches and Status LED colors TroubleshootingSwitch Function1Door lock status LED blinks every 6 seconds2Lock automatically re-locks door 30 seconds after unlocking. Disabled if no codes are programmed.3 Audio4 Not used.Color Lock StatusBlinking green UnlockedBlinking amber LockedBlinking red Low batterySolid redDoor handing process did not work properly. See the online Programing and Troubleshooting Guide.1 2 3 4OnSwitchesStatus LEDO System AlertsFactory ResetA factory reset will delete all codes associated with the lock, and it will remove it from your smart home system.Status LED1 Remove battery pack.2 Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED lashes red.KeypadLock buttonKeywaySmartKey tool holeButton “A” Button “B”3 Press the Program button once more. When the LED lashes green and you hear one beep, the lock has been reset.4 Perform the door handing process again to teach the lock the orientation of the door, pair the lock with your smart home system, and add user codes to your lock. A complete SmartCode 914 Programming and Troubleshooting Guide is available at www.kwikset.com.

Navigation menu