Spectrum 450412ZWV 914C Zwave Electronic Door Lock User Manual 13 Users Manual

Download:
Mirror Download [FCC.gov]
Document ID	3342158
Application ID	aA1GRIdLl7pS+XRDbeZFgg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	362.01kB (4525092 bits)
Date Submitted	2017-03-31 00:00:00
Date Available	2017-03-31 00:00:00
Creation Date	2017-03-31 16:52:50
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2017-03-31 16:54:17
Document Title	13 Users Manual.pdf
Document Creator	Adobe InDesign CC 2015 (Windows)
Document Author:	director

61890 / 01
Regulatory Compliance
Cumplimiento Normativo
Conformité règlementaire
This product complies with standards established by the following
regulatory bodies:
Este producto cumple con las normas establecidas por los
siguientes organismos reguladores:
Ce produit est conforme aux normes établies par les organismes de
règlementation suivants :
•
•
•
•
•
•
Federal Communications Commission (FCC)
Industry Canada
Comisión Federal de Comunicaciones (FCC)
Industry Canada
Federal Communications Commission (FCC)
Industrie Canada
FCC
FCC
FCC
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: ( 1 ) this device may
not cause harmful interference, and ( 2 ) this device must accept
any interference received, including interference that may cause
undesired operation.
Este dispositivo cumple con la 15ª parte del reglamento de la FCC.
Su funcionamiento está sujeto a las siguientes dos condiciones:
( 1 ) este dispositivo no deberá causar ninguna interferencia dañina,
y ( 2 ) este dispositivo deberá aceptar cualquier interferencia
recibida, incluyendo aquélla que podría causar un funcionamiento
no deseado.
Cet appareil est conforme aux limites prescrites dans la partie 15
des règlements de la Federal Communication Commission (FCC)
des États-Unis. Son utilisation est subordonnée aux conditions
suivantes : ( 1 ) l’appareil ne doit pas causer d’interférence nuisibles,
et ( 2 ) il doit accepter toute interférence, y compris celles qui
peuvent causer son mauvais fonctionnement.
Se realizaron pruebas a este equipo cuyos resultados revelaron que
cumple con los límites establecidos para un dispositivo digital de
la Clase B, conforme a la 15ª parte del reglamento de la FCC. Estos
límites han sido impuestos para proporcionar protección razonable
contra interferencias dañinas en una instalación residencial. Este
equipo genera, utiliza y puede irradiar energía de radiofrecuencia
y, si no se instala y utiliza según lo que indican las instrucciones,
podría causar interferencia dañina en radiocomunicaciones. Sin
embargo, no hay garantía de que la interferencia no ocurrirá en
determinadas instalaciones. Si este equipo efectivamente causa
interferencia en la recepción de radio o televisión, la cual puede
determinarse encendiendo y apagando el equipo, sugerimos al
usuario que intente corregir dicha interferencia tomando una o más
de las siguientes medidas:
Lors des tests effectués, cet appareil s’est révélé conforme aux
limites prescrites dans la partie 15 des règlements de la Federal
Communications Commission (FCC) des États-Unis pour un
appareil numérique de Classe B. Ces limites ont été fixées pour
protéger raisonnablement les installations résidentielles contre les
interférences nuisibles. L’appareil produit, utilise et peut émettre
des radiofréquences. S’il n’est pas installé et utilisé de la façon
prescrite, il peut brouiller les communications radio. Il n’est pas
garanti qu’aucune interférence ne se produira. Si l’appareil brouille
la réception d’une radio ou d’un téléviseur (pour savoir s’il est
à l’origine du brouillage, il suffit de l’éteindre et de le rallumer),
l’utilisateur est invité à tenter de corriger la situation en prenant une
ou plusieurs des mesures suivantes :
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
IMPORTANT! Changes or modifications not expressly approved by
the manufacturer could void the user’s authority to operate the
equipment.
Industry Canada
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
( 1 ) this device may not cause interference, and ( 2 ) this device
must accept any interference, including interference that may
cause undesired operation of the device.
•
•
•
•
Volver a orientar o ubicar la antena receptora.
Incrementar la distancia entre el equipo y el recibidor.
Conectar el equipo a una toma de corriente en un circuito
distinto del circuito en el cual esté conectado el recibidor.
Consultar con el distribuidor o un técnico de radio y TV con
experiencia para obtener su ayuda.
¡IMPORTANTE! Todo cambio o modificación no aprobado
expresamente por el fabricante podría desautorizar al usuario para
operar el equipo.
Industria de Canada
Este dispositivo cumple con las normas de la Industria de Canada
licencia-exenta RSS. Su funcionamiento está sujeto a las siguientes
dos condiciones: ( 1 ) este dispositivo no deberá causar ninguna
interferencia dañina, y ( 2 ) este dispositivo deberá aceptar
cualquier interferencia, incluyendo aquélla que podría causar el
funcionamiento no deseado del dispositivo.
•
•
•
•
réorienter ou déplacer l’antenne réceptrice;
éloigner davantage l’appareil émetteur du récepteur;
brancher l’appareil dans une prise reliée à un circuit différent
de celui auquel le récepteur est relié;
consulter le détaillant ou un technicien de radiotélévision
expérimenté pour obtenir de l’aide.
IMPORTANT! Les modifications qui n’ont pas été expressément
approuvées par le fabricant de l’appareil peuvent annuler
l’autorisation d’utiliser l’appareil.
Industrie Canada
Cet appareil est conforme aux normes d’Industrie Canada exemptes
de licence RSS. L’opération est sujette aux deux conditions: ( 1 ) ce
dispositif peut ne pas causer l’interférence et ( 2 ) ce dispositif doit
accepter n’importe quelle interférence, y compris l’interférence qui
peut causer le fonctionnement non souhaité du dispositif.
66452-001
Rev 01
Z-Wave® Plus
Parts in the box
Black components
ENGLISH
Mounting plate
Gold components
Mounting plate
screws
Mounting plate
Silver components
Mounting plate
screws
Mounting plate
Mounting plate
screws
LOGO FPO
Adapter
Installation and User Guide
Interior cover
Adapters
Interior assembly
Battery pack
Adapter
AA batteries
Interior assembly
screws
Interior cover
screws
49191
64109
Required tools
Ruler
Kwikset
1-800-327-5625
www.kwikset.com
Existing key
Phillips head screwdriver
Prepare your door
Make sure your existing deadbolt is compatible. If you have a standard deadbolt
mounted separately from the handle below it, it is compatible with Kwikset Convert.
Compatible
Not Compatible
Not Compatible
Rim
Lock
Measure to confirm that your door is either
1-3/8" or 1-3/4" (35 mm or 44 mm) thick.
Not Compatible
Mortise
Lock
Integrated
Interior
Make sure your door is open and
extend your latch bolt.
Remove all existing deadbolt hardware from the interior
side of your door. Keep your deadbolt exterior in place.
deadbolt
exterior
1-3/8"or 1-3/4"
35 or 44 mm
extended
For a list of compatible deadbolt
models, please see the Kwikset
Convert page at www.kwikset.com
Determine the parts needed for your door
Look into the hole in your door.
What shape is your torque blade (the part sticking out through the latch)?
D-shape
Vertical rectangle
Kwikset and Weiser deadbolts:
Use the black component kit for your door.
Baldwin deadbolts:
Use the gold component kit for your door.
Use the gold component kit for your door.
You will need the gold adapter with the vertical slot
and the thinner gold screws.
thinner
screws
You will need the black adapter with the
D-shaped hole and the thicker gold screws.
thicker
screws
D-shaped
hole
1/4
vertical slot
Slanted rectangle
Use the silver component kit for your door.
3
Install the mounting plate and test your latch
Place the mounting plate on the door so that the torque
blade inserts through the center hole.
Secure the mounting plate with the mounting screws.
Keep parallel to the
edge of the door.
Black Components Only: To
determine which mounting
screws to use, test one of
the thicker screws first.
If the thicker screw fits, continue
installing the thicker screws.
If the thicker screw doesn't fit,
install the thinner screws.
torque blade
Tighten
screws evenly.
Note: A D-shaped torque blade is shown, but installation is the same for all models.
Insert your key and test the latch for smooth operation.
Remove your key and make sure the bolt is fully extended.
fully
extended
If the latch does not
extend or retract
smoothly, adjust the
mounting screws.
Prepare the interior assembly
Temporarily install the interior cover to correctly orient the turnpiece shaft.
Remove the battery pack.
Lay the interior assembly on a flat
surface, and install the interior cover.
Rotate the turnpiece so that its
narrow tip faces the Status LED.
Remove the interior
cover from the
interior assembly.
Status LED
Do not
install
batteries
yet.
If the interior cover does not lay
flush, rotate the turnpiece. When the
Status LED pops into place, the cover
is flush and correctly aligned.
Install the adapter on the interior assembly.
SILVER COMPONENTS ONLY:
Look at your mounting plate.
Is your latch bolt to the left or right of your mounting plate?
Left
Right
Silver adapter:
Tab is on bottom.
Gold adapter:
Keep slot vertical.
No adjustment is required.
Proceed to next step.
Make the following adjustments:
1. Unlock your deadbolt.
align tabs
Black adapter:
Curve is on top.
Unlocked
2. On your interior assembly, flip
switch #2 to the top position.
Switch #2
Press adapter firmly onto
the interior assembly.
2/4
5
Install the interior assembly
Align the adapter with the torque blade.
Secure with two (2) interior assembly screws.
bottom
hole
Perform the door handing process
This step will teach the lock the orientation of your door and is crucial for lock operation.
Install 4 AA batteries in
the battery pack.
Make sure the door is open. Insert the battery
pack while PRESSING AND HOLDING the
Program button. Release the button when the
battery pack is all the way inside the lock interior.
The Status LED will flash red and green, and
the lock will beep. Press and release the
Program button again. The latch bolt will
retract and extend on its own.
Ensure correct polarity. For best
results, use new, non-rechargeable
Alkaline batteries only.
If the latch bolt did
not move, remove the
battery pack, wait 15
seconds, then attempt
the process again.
status LED
Pair the lock with your smart home system
Initiate the pairing process at
your smart home controller.
Refer to your smart home system
instructions for more information.
When prompted by your smart home system
to initiate pairing at the lock, press button “A”
on the lock interior one time. The red LED will
illuminate when pairing mode has been entered.
button “A”
If the pairing process is successful, re-name
the lock in your system (if applicable).
If pairing is unsuccessful, follow your system's
instructions to remove the lock from the
controller and any other network, then
press button “A” on the lock one time.
Perform steps 7A-7C again.
If pairing is still unsuccessful, see
"Troubleshooting: Lock won't pair with
smart home system" on page 4.
Please allow time for the controller to pair with the lock.
Install the interior cover
Important Information about the interior cover
The interior cover will be
installed over the back panel
with three screws.
If the window is unlocked, it can
slide up for quick access to the
buttons while the cover is installed.
The window on the interior cover is
locked by default to prevent someone
from tampering with the back panel.
If you want to keep the window locked:
If you want to unlock the window (for quick access to back panel):
Install
cover.
Remove
security
screw.
Install
screws.
Install
cover.
3/4
Install
screws.
Reference Guide
Switches
Kwikset Convert at a Glance
Button “A”
Back panel
Button “B”
Program button
2 3 4
Switches
Status LED
1. Status LED
3. Audio
Door lock status LED blinks
every 6 seconds. ON position
is factory default.
Beeping sound is heard during
programming and normal operation.
ON position is factory default.
2. Invert
4. Auto-Lock
Only used for right-handed
doors that have installed
silver components.
Automatically re-locks door 30
seconds after unlocking. OFF
position is factory default.
CAUTION: With this feature
enabled, it is possible to lock yourself
outside if you don’t have an enrolled
smartphone or standard key with you.
on off
Turnpiece shaft
Status LED Notifications
Factory Reset
A factory reset will delete all codes associated with the lock.
1 Remove
battery pack.
Amber flash
Door is locked
Green flash
Door is unlocked.
2 Press and HOLD the
Program button while
reinserting the battery pack.
Keep holding the button
for 30 seconds until
the lock beeps and the
status LED flashes red.
Red flash
The 4 AA batteries in
the Kevo interior are
low and need to be
replaced.
3 Press the Program
button once more. When
the LED flashes green
and you hear one beep,
the lock has been reset.
Status
LED
4 Perform the door handing process
again to teach the lock the
orientation of the door and pair the
lock to your smarthome system.
Troubleshooting: Lock won't pair with smart home system
Some Z-wave systems require that the lock be within 12" of the controller during the pairing
process. If this is the case, follow the steps below to remove the lock interior from the door
to perform the pairing process closer to the controller:
1. Remove the small screws that secure the
interior assembly to the mounting plate.
2. Remove the interior assembly from the door.
3. Hold the interior assembly a maximum of 12" (305 mm) from
your smart home controller for the rest of this process.
12"
305 mm
4. Initiate the pairing process at your smart home
controller. Refer to your smart home system
instructions for more information.
5. When prompted by your smart home system to
initiate pairing at the lock, press button “A” on the
lock interior one time. The red LED will illuminate
when pairing mode has been entered.
Z-Wave
Controller
6. When pairing is complete, re-name the lock in
your system (if applicable). Then, reinstall the
lock interior on the interior assembly.
Z-Wave
Controller
12"
305 mm
The lock and controller must remain stationary for
at least 60 seconds during the pairing process.
Network Information
Important Safeguards
Removing the lock from the network
1.
2.
3.
4.
5.
Read all instructions in their entirety.
Familiarize yourself with all warning and caution statements.
Remind all family members of safety precautions.
Always have access to your lock’s standard key.
If using the Auto-Lock feature, make sure to have your smartphone
or standard key with you to prevent locking yourself out.
6. Replace low batteries immediately.
Follow your smart home system’s instructions
to remove the lock from the network. When
prompted by the system, press button A” on the
lock interior once.
Z-Wave System Notes
This product is a security enabled Z-wave Plus product and must be used with a Security
Enabled Z-Wave controller to be fully utilized. Z-Wave is a “Wireless mesh network,” and
results may vary based on building construction and communication path, with 35 feet+
being typical installed distance from smart home controller. It may be necessary to install
additional Z-Wave beaming capable devices that can serve as repeaters to enhance the
communication path between the lock and controller for a more robust Z-Wave network.
CAUTION: Prevent unauthorized entry. Restrict access to your lock’s back panel and
routinely check your settings to ensure they have not been altered without your
knowledge.
WARNING: This Manufacturer advises that no lock can provide complete security
by itself. This lock may be defeated by forcible or technical means, or evaded by
entry elsewhere on the property. No lock can substitute for caution, awareness of
your environment, and common sense. Builder’s hardware is available in multiple
performance grades to suit the application. In order to enhance security and reduce
risk, you should consult a qualified locksmith or other security professional.
To assure interoperability, each Z-Wave product must pass a stringent conformance test to
assure that it meets the Z-Wave standard for complete compliance with all other devices and
controls. The Z-Wave identity mark assures consumers, integrators, dealers and manufacturers
that their products will reliably perform with any other Z-Wave device. And, regardless of the
vendor, always powered nodes may act as a repeater for Kwikset/Weiser/Baldwin products.
Z-Wave Configuration and Association Parameters are available on
the Kwikset Convert page at www.kwikset.com.
4/4
© 2016 Spectrum Brands, Inc.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Author                          : director
Create Date                     : 2017:03:31 16:52:50-07:00
Modify Date                     : 2017:03:31 16:54:17-07:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2017:03:31 16:54:17-07:00
Creator Tool                    : Adobe InDesign CC 2015 (Windows)
Instance ID                     : uuid:10929b34-f8ff-4772-834e-4b20b3ab0b6a
Original Document ID            : xmp.did:D395E8E59F2CE411BF98BFEF58C949FE
Document ID                     : xmp.id:9f7bbcb5-2b64-6d4d-89e6-cf815d971dcb
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:4b2edfc8-a35b-c84c-912d-f39dcaf63200
Derived From Document ID        : xmp.did:cda2ba3f-44cd-1e4c-84f3-695942033663
Derived From Original Document ID: xmp.did:D395E8E59F2CE411BF98BFEF58C949FE
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2015 (Windows)
History Changed                 : /
History When                    : 2016:09:01 11:33:56-07:00
Format                          : application/pdf
Creator                         : director
Title                           : 13 Users Manual.pdf
Producer                        : Acrobat Distiller 11.0 (Windows)
Trapped                         : False
Page Count                      : 5

EXIF Metadata provided by EXIF.tools