Spotwave Wireless SPOTCELL0013 DU 1900 Full Band User Manual SpotCell 11x QuickStart 14Sep04

Download:
Mirror Download [FCC.gov]
Document ID	485000
Application ID	YzXFCO/KYqgIyPJ7Jxd4mw==
Document Description	Quick start guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	38.18kB (477197 bits)
Date Submitted	2004-11-03 00:00:00
Date Available	2004-11-03 00:00:00
Creation Date	2004-09-19 19:01:35
Producing Software	Corel PDF Engine Version 1.0.0.536
Document Lastmod	2004-09-19 19:01:35
Document Title	SpotCell_11x(S)_QuickStart_14Sep04.cdr
Document Creator	CorelDRAW Version 12.0
Document Author:	Mark Boyle

™
SpotCell 111s/112s
Quick Installation Guide
www.spotwave.com
Spotwave Wireless Inc. 1 Hines Road, Ottawa ON K2K 3C7 Canada
© 2004 Spotwave Wireless Inc. All rights reserved. Printed in Canada
Spotwave and SpotCell are trademarks of Spotwave Wireless Inc. Patents pending.
780-0000x-01-01
For quick installation of SpotCell:
If required, more detailed information on installing a
SpotCell system can be found in the User Manual
1. Parts List
which is also available for downloading at
www.spotwave.com/2003/support/manuals.htm.
• Donor Unit (DU)
• Cable (80'/25 m)
• Coverage Unit (CU) • Power supply
2. Location
DU
(outward-facing unit)
WARNING
• Mounting kit
CU
(indoor unit)
The DU can be mounted anywhere your cell
phone works. This may be on a rooftop (typical
rural set-up), on the side of a building, or inside
a building (typical downtown set-up). The CU
will be mounted inside the building where your
cell phone does not work.(The illustration at
the right depicts a typical installation.)
To start the installation, place the DU and CU
in the general areas where they are to be located.
Do not physically mount them at this time.
For your safety ,beware of power lines and ensure that
appropriate safety measures are maintained at all times
during the installation of the SpotCell 100 equipment.
Contact with high-voltage power lines could result in
death or serious injury.
Maximum separation between the DU and CU,
and back-to-back positioning are optimal when
both are mounted indoors.
3. Connect CU to DU
4. Set Mode and AP Switch
5. Align DU - 1st rotation
6. Align DU - 2nd rotation
Connect the CU and DU with the cable provided.
Set the switch on the bottom of the CU to “1” (install).
If only one of the split bands is currently active, then set the
AP switch to the active band. If both bands are active, then
the AP switch can be in either position for DU alignment.
Connect the power supply to the CU, and then plug the
adapter into the AC outlet.
In the location where the DU is to be mounted, rotate the
unit in a complete circle. The LED on the back will turn red
or green during the rotation.
Again rotate the DU. When the LED turns green, stop the
rotation. This is the direction the DU must face when
mounted.
Back of DU
Back of CU
Power
Connector
AP
Switch
Back of CU
Mode
Switch
LED
Rotate 360°
7. Mount DU
8. Set CU to Active
9. Mount CU
10. Final Checklist
Now mount the DU. Typical installations are pictured below .
Move the switch on the bottom of the CU to “2” (active).
Hold the CU in the location to be mounted. The LCD on
the bottom of the CU indicates coverage ( ) by the number
of bars; more bars indicate better coverage.
Mount the CU from a wall or ceiling, close to the center
of the area requiring coverage.
1.Properly ground the DU via the grounding bolt.
Wall Mount
Pipe Mount with Hose Clamp
2.Ensure that there is a drip loop on the cable connecting
to the DU.
3.Firmly affix the cable to the building where it runs
between the DU and CU.
CHxxx
I n S er v i ce

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2
Create Date                     : D:20040919190135
Modify Date                     : D:20040919190135
Producer                        : Corel PDF Engine Version 1.0.0.536
Author                          : Mark Boyle
Creator                         : CorelDRAW Version 12.0
Title                           : SpotCell_11x(S)_QuickStart_14Sep04.cdr

EXIF Metadata provided by EXIF.tools