Square SPB1 Square Register User Manual

Square, Inc. Square Register

User Manual

Download: Square SPB1 Square Register User Manual
Mirror Download [FCC.gov]Square SPB1 Square Register User Manual
Document ID3581373
Application IDWw2/xAekBIwMq5c1S8TEdA==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize13.53kB (169081 bits)
Date Submitted2017-09-26 00:00:00
Date Available2017-09-26 00:00:00
Creation Date2017-08-30 14:15:25
Producing SoftwareAdobe PDF Library 15.0
Document Lastmod2017-08-30 14:15:26
Document TitleUser Manual
Document CreatorAdobe InDesign CC 2017 (Macintosh)

Getting Started
1455 Market Street, Suite 600, San Francisco, CA 94103
PROJECT
DESIGN
X2 Packaging
Eric Manago
DELIVERABLE
SIZE
GSG - US - 16 pages
INKS 1/1 + Anti-scuff Matte AQ
Flat: 288mm x 144mm
Folded: 144mm x 144mm
COPYWRITING
CREATIVE
Approved
Changes
MATTE AQ
PRODUCTION
Jordan Lebrecht
MATERIAL
130gm couche
PART #
M-LIT-0094
FINISHING
Diecut, score, fold, staple
PRODUCTION NOTES
REV
-03
VENDOR
Veritiv China
Adhesive _______
_______
Dieline
______
Perf
VERSION
M08
MODIFIED
August 30, 2017 2:14 PM
REV NOTES
M-LIT-0094-03_X2_GSG_16-pages_US_M09
APPROVALS
Approved
Changes
BLACK
FILE NAME
CONTRIBUTORS
EDITING
Approved
Changes
REV-02 (06/17): Added 4 pages,
updated content.
REV-03 (08/17): Added regulatory
language
LOCALIZATION
Approved
Changes
IMAGING
Approved
Changes
OTHER __________
Approved
Changes
LEGAL
Approved
Changes
PMM (MARKETING)
Approved
Changes
COUNTRY MANAGER
Approved
Changes
PROGRAM MANAGER
Approved
Changes
WELCOME TO SQUARE
Let’s get your Square Register up and running. Start by taking a quick look at what’s in the box.
1. Power adapter cable
2. Power adapter
3. Accessory hub
4. Customer display cable
5. Mounting plate with cleat
6. Mounting tools
Square Register
Customer Display
Power button
Micro
USB port
Front
Mounting plate
cleat slot
Micro USB ports
Customer display
release latch
Back
GET SET UP
1. Separate the customer display
Remove the instructional wrap, carefully lift the
customer display out of Register, and remove
the protective foam pad. Place the customer
display aside for now—make sure you lay it
down flat.
3. Connect the power adapter to the
accessory hub
2. Connect the accessory hub to Register
4. Plug it in
Simply plug the cable into one of the micro
USB ports located on the bottom of Register.
With the power adapter cable, plug one end
into the power adapter and the other end into
a power outlet.
GET SET UP (CONTINUED)
5. Choose a setup
6. Power up
Docked
Press the power button on the base of the
Register display until the Square logo appears
on the screen.
Simply place the customer display back into
its slot on Register. Press firmly on the edges
of the customer display to ensure it’s locked
in place. If you need to undock the customer
display, hold in the release latch located on
the bottom of Register and lift the customer
display out.
Undocked
7. Sign in
Grab the included customer display cable.
Plug one end into the customer display and
the other end into the bottom of Register.
You can now sign in with your Square account. If you’re new to Square,
create your free account at square.com/signup.
All set up? Learn how to create items, add your business logo to the customer display, and more at
square.com/register-setup.
HOW TO TAKE PAYMENTS
Docked
Undocked
Position Register so your customers can easily see the customer display and pay with their cards
and devices. To take a payment, ring up the sale and tap Charge.
Make sure the customer display is correctly oriented so it’s sitting horizontally on your
countertop. Position the customer display so your customers can easily see it and pay with
their cards and devices. To take a payment, ring up the sale and tap Charge.
Tap
Dip
Swipe
Tap
Dip
Swipe
Ask your customer to hold
a contactless device or card
near the customer display to
trigger payment.
Ask your customer to insert
a chip card into the chip card
slot on the customer display
and leave it in place until the
sale is complete.
Ask your customer to swipe a
magnetic-stripe card through
the magstripe reader on the
customer display.
Ask your customer to hold
a contactless device or card
near the customer display to
trigger payment.
Ask your customer to insert
a chip card into the chip card
slot on the customer display
and leave it in place until the
sale is complete.
Ask your customer to swipe a
magnetic-stripe card through
the magstripe reader on the
customer display.
MOUNT SQUARE REGISTER TO YOUR COUNTER WITH ADHESIVE
1. Pick a spot
3. Position properly
 sing a damp cloth, clean the area where you
want to secure Register. Wait for the surface
to dry completely.
 ake sure the raised cleat of the mounting
plate is on your side of the counter, not the
customer’s side. Adhere the plate to your
counter in the desired position and press down
firmly for 30 seconds. Wait 30 minutes for the
adhesive to set. If you need to remove the plate,
slowly pull the tabs on the adhesive strips until
they release.
2. Prepare the adhesive strips
4. Twist and lock
Grab the mounting plate. Remove the backing
from the adhesive strips located on the
underside of the plate.
Place Register onto the mounting plate with the
larger screen facing right. Make sure the cleat is
positioned in its slot. Turn Register 90 degrees
clockwise so it locks in place.
MOUNT SQUARE REGISTER TO YOUR COUNTER WITH SCREWS
1. Pick a spot
3. Position properly
Grab the mounting plate. Pick a spot on your
counter for Register, position the plate, and
use a pencil to mark the four screw holes on
your counter. Make sure the raised cleat is on
your side of the counter, not the customer’s
side. Note: Maximum counter thickness is
2 inches (50 mm).
Position the mounting plate onto the holes
you’ve drilled, then insert a screw into each
hole. From the underside of your counter, place
a thumb nut onto each screw and tighten until
the thumb nut is flush against your counter.
2. Drill your counter carefully
4. Twist and lock
You need a drill and the included tools: drill bit,
screws, and thumb nuts. Use the drill and drill
bit to make the four holes you’ve marked
for the plate.
Place Register onto the mounting plate with the
larger screen facing right. Make sure the cleat is
positioned in its slot. Turn Register 90 degrees
clockwise so it locks in place.
HOW TO USE THE ACCESSORY HUB
HELP AND SUPPORT
The accessory hub gives you USB ports to connect a cash drawer, printer, or bar code scanner, and an
Ethernet port if you need a wired internet connection. To learn more about setting up accessories and
connecting to the internet, go to square.com/register-setup.
Read our FAQs, learn more about compatible hardware, and get troubleshooting support at
square.com/register-setup.
HARDWARE WARRANTY
You’re covered from defects for up to two years under a limited warranty. See square.com/warranty.
Ethernet port
FREE 30-DAY RETURNS
Cash drawer
Receipt printer
Order ticket printer
Bar code scanner
Note: Only use the Ethernet port for connecting Square Register to the internet.
Square offers a 30-day, risk-free return policy for all purchases made from square.com/shop.
Simply go to square.com/returns so we can make things right. After a return is complete, a
refund will be credited back to you.
REGULATORY INFORMATION
You can view regulatory information for Square Register by going to Settings > General > About Register > Regulatory. To view FCC information, go to
Support > Legal > Hardware Disclaimer.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
ACCESSORY HUB INFORMATION
Hub output provides power to peripherals. Register output provides power to Square Register.
© 2017 Square, Inc., 1455 Market St., Ste. 600, San Francisco, CA 94103. Square, the Square logo, and Square Register are trademarks of Square, Inc.
M-LIT-0094-03
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Language                        : en-US
XMP Toolkit                     : Adobe XMP Core 5.6-c138 79.159824, 2016/09/14-01:09:01
Create Date                     : 2017:08:30 14:15:25-07:00
Metadata Date                   : 2017:08:30 14:15:26-07:00
Modify Date                     : 2017:08:30 14:15:26-07:00
Creator Tool                    : Adobe InDesign CC 2017 (Macintosh)
Instance ID                     : uuid:053992dc-fa25-bb44-b122-c6e56d13664a
Original Document ID            : xmp.did:F77F1174072068118083C1692770F97F
Document ID                     : xmp.id:6a597fcd-148e-4dad-871a-76f4ac22d51a
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:df4069e3-5710-47e6-8ab3-0f9096f4d410
Derived From Document ID        : xmp.did:df4069e3-5710-47e6-8ab3-0f9096f4d410
Derived From Original Document ID: xmp.did:F77F1174072068118083C1692770F97F
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2017 (Macintosh)
History Changed                 : /
History When                    : 2017:08:30 14:15:25-07:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 9
Creator                         : Adobe InDesign CC 2017 (Macintosh)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: 2AF3K-SPB1

Navigation menu