Standard Communications CM1039V VHF MOBILE TRANSCEIVER User Manual

Standard Communications Pty Ltd VHF MOBILE TRANSCEIVER

User Manual

Download: Standard Communications CM1039V VHF MOBILE TRANSCEIVER User Manual
Mirror Download [FCC.gov]Standard Communications CM1039V VHF MOBILE TRANSCEIVER User Manual
Document ID2483966
Application IDftT0S70BhsIE2YE3fDEcqA==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize121.92kB (1524033 bits)
Date Submitted2014-12-24 00:00:00
Date Available2015-06-22 00:00:00
Creation Date2014-07-18 16:44:23
Producing SoftwareAcrobat Distiller 9.0.0 (Windows)
Document Lastmod2014-07-18 16:49:10
Document TitleMicrosoft Word - CM1039 USA Instruction Manual Rev_D.docx
Document CreatorPScript5.dll Version 5.2.2
Document Author: ianlind

CM1039
PROFESSIONAL SERIES MOBILE RADIO
INSTRUCTION MANUAL
Copyright Notice
Standard Communications Pty Ltd reserves all rights to this document and the information
contained herein. Reproduction, use or disclosure to third parties without the express
permission is strictly prohibited.
Copyright 2013
Standard Communications Pty Ltd
Sydney, Australia
RADIO FREQUENCY EXPOSURE HAZARD
Attention
This radio should be used only in an occupational (work related) environment where the
user is aware of and able to exercise control over their exposure to RF energy. This radio is
not authorized for use by the consumer or by the general population.
To comply with the US FCC radio frequency guidelines and to ensure your safety please read
the following information before installing and using the radio.




Use the radio only within the guidelines of this manual.
Use only with an approved antenna.
Do not remove the RF Exposure label from this radio.
Do not transit longer than the rated duty cycle of 50% talk‐50% listen.
Radio Frequency Exposure Control
This radio emits RF (Radio Frequency) energy or radio waves when transmitting. RF energy is
one of many forms of electromagnetic energy including sunlight and electricity. The FCC
Radio Frequency exposure guidelines include recommendations on the safe levels of
exposure for workers and the general public with a significant margin of protection.
To comply with FCC exposure limits the radio must be installed using an externally mounted
antenna with a gain of either 2.15 dBi or 5.15 dBi. Transmit only when bystanders are at a
minimum safe distance of 35 inches (0.9 m) from the antenna.
For further information on RF energy exposure and how to control it, please visit the
following website. www.fcc.gov/oet/rfsafety/rf‐faqs.html
Compliance with RF Energy Standards
This radio is designed and tested to comply with a number of national and international
standards and guidelines (listed below) regarding human exposure to RF electromagnetic
energy. This radio complies with the IEEE and ICNIRP exposure limits for
occupational/controlled RF exposure environment at duty cycles of up to 50% talk‐50%
listen and should be used for occupational use only. In terms of measuring RF energy for
compliance with the FCC exposure guidelines, your radio radiates measureable RF energy
only when it is transmitting (during talking), not when it is receiving (listening) or in standby
mode.
This radio complies with the following RF energy exposure standards and guidelines:




United States Federal Communications Commission, Code of Federal Regulations;
47CFR part 2 sub‐part J
American National Standards Institute (ANSI)/Institute of Electrical and Electronic
Engineers (IEEE) C95. 1‐1992
Institute of Electrical and Electronic Engineers (IEEE) C95. 1‐1999 edition
International Commission on Non‐Ionizing Radiation Protection (ICNIRP) 1998
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
USING THE RADIO IN EXPLOSIVE ATMOSPHERES OR BLASTING AREAS
Switch off your radio before entering any area where there may be inflammable gas, liquids
or dust. An explosion could result in serious injury or death.
Switch off your radio when approaching a blasting area. Blasting areas are usually sign
posted with instructions to users to turn off two way radios. Strong radio transmissions
could ignite blasting caps resulting in an unscheduled explosion resulting in serious injury or
death.
INSTALLATION GUIDELINES

Do not install the radio near an airbag or in an area where an airbag may deploy. If
an airbag is obstructed by the radio, it may not deploy as expected. It could also
propel the radio with enough force to cause serious injury.

Avoid touching the heat sink at the rear of the radio while the radio is in use. The
heat sink can become hot during prolonged use.

Do not install the radio in front of a vehicle heater. The radio requires a cool airflow
over the rear heat sink when transmitting to maintain efficiency.

Do not make unapproved modifications to the radio. Such modifications could void
the warranty and cause the radio to operate outside its approved specifications.
Interference with Vehicle Electronics
Some of the electronics in your vehicle may be susceptible to RF energy when your radio is
transmitting. Examples of electronic devices in your vehicle that could be affected are anti‐
lock/anti‐skid braking systems, cruise control systems and fuel injection systems. If your
vehicle is fitted with any of these systems please consult your vehicle manufacturer to
determine whether these systems are likely to be affected by your radio when it is
transmitting. Careful selection of mounting locations and good installation techniques
should generally minimize any interference to your vehicle electronics.
CONTENTS
INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PRIMARY CONTROLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MC513BC Microphone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROGRAMMABLE KEYS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MENU NAVIGATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Backlight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TX Power Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Squelch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Squelch Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Beep Volume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Firmware Version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Serial Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selective Call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTMF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MCD1200 Digital Data Signaling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CTCSS/DCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Monitor Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Zones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scan Nuisance Delete. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dynamic Regrouping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Failsoft Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting the Cradle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fitting the Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fitting the MC513BC Microphone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Microphone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Console Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DC Power Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Antenna Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
10
10
10
11
11
12
12
12
13
13
13
14
14
17
18
20
20
21
21
21
22
22
22
23
23
24
24
25
26
INTRODUCTION
The GME CM1039 Series is a 25W Commercial radio which will operate in the VHF 136 – 174
MHz, UHF(H) 450MHz – 512MHz and UHF(L) 403MHz – 470MHz bands.
GME CM1039 Series radios represent a significant opportunity for both large and small
network operators to effectively future proof their communications systems. The CM1039
series of mobile radios permits fleet transition from a simple, yet fully featured analog
transceiver to a totally compliant conventional or trunked P25 digital solution.
The GME CM1039 supports a range of configurable options to suit any application and
virtually any vehicle installation challenge.
The CM1039 Series can operate in three modes:
1. Conventional analog
2. P25 Conventional
3. P25 Trunked with encryption and data
FEATURES











Local and Remote configurations
Scan
RSSI Voting
1072 Channels
50 Zones
Selcall (analog mode)
MDC1200 (analog mode)
CTCSS
DCS
Programmable function keys
Channel profiles
PRIMARY CONTROLS
Front Panel
Channel /
Select Knob
Microphone
Socket
F1 Function
Key
Display
F2 Function
Key
F3 Function
Key
On/Off Volume /
Clear Knob
F4 Function
Key
Rear Panel
Extension
Speaker
Antenna
Socket
12V DC
Connection
Rear Mic
Socket
MC513BC Microphone
Call Key
Push‐To‐Talk
Key
Down Key
UP Key
Dash (‐) Key
PROGRAMMABLE KEYS
The functions of the following buttons are determined through dealer programming.







Select (SEL) knob)
Clear (CLR) knob )
F1 Key
F2 Key
F3 Key
F4 Key
Call Key (MC513BC top)

Dash (‐) Key (MC513BC front)
MENU NAVIGATION
The menu is used to adjust settings within the radio. Menu items can be individually
enabled or disabled by the dealer programmer. Depending on how it is programmed, the
menu in your radio may only include a small selection of the possible items listed below or it
may be disabled completely.
An enabled menu item may not be applicable to all installed channels; however, the menu
item will always remain visible in the menu. Attempts to select the invalid menu item will
result in an error beep.
Menu Navigation ‐ General
To access the menu, press the SEL knob. Rotate the SEL knob to scroll through the available
menu options. Press the SEL knob again to select the displayed option. For submenu items,
rotate the SEL knob again until the required submenu item is displayed then press the knob
to select.
Example: To adjust the Beep Tone volume level;
1.
2.
3.
4.
5.
6.
Press SEL to access the Menu.
Rotate to ‘SETTINGS’ then press SEL.
Rotate to ‘ALERT LEVEL’ then press SEL.
Rotate to ‘BEEP VOLUME’ then press SEL.
Rotate the knob to adjust the Beep Volume level.
Press SEL to accept the change and return to the previous menu level
To step back to the previous menu option at any time, press the CLR (volume) Knob. To exit
the menu completely and return to the normal display, press and hold the CLR knob.
Note: The Menu option will timeout after 5 seconds if no further menu selections are made.
Menu Map
The following Menu Map represents all of the available menu options. Only the menu items
that have been enabled in your radio will actually appear in your radio’s menu.
GENERAL OPERATION
BACKLIGHT
The LCD back light brightness level is adjustable in 16 steps from off to full.
To adjust the back light brightness;
1.
2.
3.
4.
5.
6.
Press SEL.
Rotate to ‘SETTINGS’ and press SEL.
Rotate to ‘DISPLAY’ and press SEL.
Rotate to ‘BKLGT’ and press SEL.
Rotate to select the required brightness setting.
Press SEL to accept.
TX POWER LEVEL
Sets the global maximum transmit power for the radio. The user can select from 1 of 4
levels: 1W, 5W, 10W, 25W.
Note: Individual channels can also have their own power settings in which case the transmit
power for the selected channel will be the lower of the two power settings.
E.g. If a channel is set for 10W and the maximum power level is 25W, then the transmit
power on that channel will be 10W. However if the maximum power is then lowered to 5W,
then the actual transmit power on that channel will be 5W.
To set the TX Power;
1.
2.
3.
4.
5.
6.
Press SEL.
Rotate to ‘SETTINGS’ and press SEL.
Rotate to ‘FUNCTIONS’ and press SEL.
Rotate to ‘TX POWER’ and press SEL.
Rotate to select the required TX power
Press SEL to accept.
SQUELCH
To turn the squelch off;
1.
2.
3.
4.
Press SEL.
Rotate to ‘SETTINGS’ and press SEL.
Rotate to ‘FUNCTIONS’ and press SEL.
Rotate to ‘SQUELCH’ and press SEL.
10
5. Rotate to select ON or OFF. The squelch will open when OFF is selected and close
when ON is selected.
6. Press SEL to accept.
Note: Squelch settings are not applicable to P25 operation.
SQUELCH LEVEL
The squelch level adjusts the sensitivity of the squelch to incoming signals. The squelch level
should be set at a point where the squelch remains closed when there are no signals
present but will open on most signals.
In quiet country or rural locations where there is little interference a lower value may be set
to allow the squelch to open on very weak signals.
In inner city applications or areas of severe interference a higher value may be necessary to
allow only stronger signals to open the squelch.
To adjust the squelch level;
1.
2.
3.
4.
5.
6.
Press SEL.
Rotate to ‘SETTINGS’ and press SEL.
Rotate to ‘FUNCTIONS’ and press SEL.
Rotate to ‘SQL LEVEL’ and press SEL.
Rotate to select the required squelch level from 1 ‐ 9
Press SEL to accept.
BEEP VOLUME
The Beep Volume adjusts the volume level of the beeps that are heard when buttons are
pressed.
To adjust the Beep Volume;
1.
2.
3.
4.
5.
Press SEL.
Rotate to ‘SETTINGS’ and press SEL.
Rotate to ‘ALERT LEVEL’ and press SEL.
Rotate to ‘BEEP VOLUME’ and press SEL.
Rotate to select the required beep volume level from 0 to 9. To disable the beeps
select 0.
6. Press SEL to accept.
11
FIRMWARE VERSION
To read the current firmware version;
1.
2.
3.
4.
5.
6.
Press SEL.
Rotate to ‘SETTINGS’ and press SEL.
Rotate to ‘RADIO INFO’ and press SEL.
Rotate to ‘VERSION’ and press SEL.
The current radio firmware version will be displayed.
Press and hold CLR to exit the menu.
ELECTRONIC SERIAL NUMBER (ESN)
To view the radio’s electronic serial number;
1.
2.
3.
4.
5.
6.
Press SEL.
Rotate to ‘SETTINGS’ and press SEL.
Rotate to ‘RADIO INFO’ and press SEL.
Rotate to ‘SERIAL NO and press SEL.
The radio’s electronic serial number will be displayed.
Press and hold CLR to exit the menu.
SELECTIVE CALL
Selective Calling (Selcall) is a secure signaling system allowing individual radios to be
selectively called without disturbing others on the same channel. Each radio can be pre‐
programmed with a unique Selcall Ident. The radio can then be set to remain totally quiet
while it monitors the channel for Selcall signals. If an incoming signal contains a Selcall
matching the Ident in your radio, an alarm sounds to alert you and the caller’s identification
is displayed on your radio. In this way, even if you are away from your radio when the call is
received, you will still know that you were called. You can then return the call at your
convenience. If further calls are received, the most recent caller is displayed.
If Selcall has been enabled on your radio, it may allow you to call others who are also using
the Selcall system. It may also be programmed to allowing specific groups of radios to be
called without disturbing other individuals or groups.
To make a Selcall
1. Press the Blue CALL button on the microphone.
2. ‘CALL TO’ will be displayed.
3. Press the
or
buttons on the microphone (or rotate the SEL knob) to select the
required call number programmed into your radio.
4. Hold the CALL button to make the call.
12
If the call is received successfully, a confirmation message will be displayed.
Operating in the Quiet mode
The QUIET mode prevents any incoming transmissions from being heard until your Selcall
Ident is received. This allows you to monitor a busy channel for calls without being disturbed
by unwanted signals. When your Selcall Ident is received, the QUIET mode is cancelled and
all incoming signals will be heard in the speaker.
If your radio is programmed with a Quiet key, you may be able to manually activate your
radios Quiet muting system. If not, your radio's quiet muting system will have been preset
for you by your retailer.
DTMF
Your radio may be fitted with DTMF ‘speed dial’ memories to provide pre‐programmed
DTMF sequences. If fitted, DTMF ‘speed dial’ memories can be programmed into one of
more of the function keys F1, F2, F3 or F4.
MDC1200 DIGITAL DATA SIGNALLING
MDC1200 digital / data signaling offers expanded calling functions.
MDC1200 Menu functions are located in the SERVICES menu. Available menu options are;








Call Alert
Radio Check
Status
Status Request
Message
Remote Monitor
Stun
Revive
MDC1200 – Primary use functions:


PTT‐ID
Emergency Call
CTCSS/DCS (Continuous Tone Coded Squelch System / Digitally Coded Squelch)
CTCSS/DCS are automatic coded squelch systems that allow groups of radio receivers to
remain quiet until they receive a call encoded with a specific squelch tone. The receiver's
squelch then opens to allow the call to be heard and closes again when the call is finished.
Other radios sharing the same channel but programmed with a different squelch tone will
13
not hear the call. Similarly, calls made to other radios that use a different squelch tone will
not be heard by your radio. In this way several groups of radios can share the same channel
but be almost unaware of each other's existence. One main advantage of CTCSS/DCS is it is
fully automatic with no special operation required by the user.
MONITOR
A monitor key is used to monitor (listen) to a channel that would normally remain squelched
(quiet) under the control of a CTCSS or DCS tone. When CTCSS/DCS is being used, there may
be other users talking on the channel but you will not be able to hear anything. Pressing the
Monitor key overrides the tone squelch to allow you to hear these signals. The Monitor key
is often used to check that the channel is clear before transmitting.
Note: The Monitor key does not open the Squelch; it simply overrides the CTCSS/DCS tone
decoder. If there are no signals on the channel, the radio will still remain quiet and no
receiver noise will be heard.
ZONES
The CM1039 series radio is capable of 50 zones which are used for allocating discreet
channels or talk group (P25) into zones. Zones can also be used for regional, hierarchy or
geographic grouping
A zone is a collection of channels or talk groups. Zones are used to group channels that
have something in common, such as public agency (police, fire, ambulance) or geographic
region.
When zones are enabled, the user can select channels only from the currently active zone.
If zones are not required, zones can be globally disabled. All channels then appear in one
list. The maximum channel capacity is 1072 channels.
If zones are enabled, every channel must belong to a zone and each channel can be in only
one zone at a time.
Each zone can be individually enabled. A zone containing no channels is always disabled.
When selecting a zone, the user can select only from the list of enabled zones. The
maximum number of zones is 50.
Selecting a zone
To select a zone:
1. Press SEL to access the Menu.
2. Rotate the SEL knob to select ‘ZONES’ then press SEL.
3. Rotate the SEL knob to select the desired Zone then press SEL.
While selecting a zone using the menu, the radio continues to operate on the current
14
channel in the current zone. The radio doesn't change to the selected zone until the SEL
knob is pressed. If the CLR knob pressed, the zone menu clears and the radio continues to
operate on the current channel.
Programmable keys can be assigned to the ZONE function providing direct access to the
ZONEs menu. The zone is then selected using the SEL knob.
If zones are globally disabled, the zone menu item is also disabled.
Zone Initial Channel
By default, the radio changes to the first channel in the selected zone. The first channel is
known as the home channel of the zone. Optionally the radio can be configured to save the
current channel in the current zone before changing to the selected zone. The radio then
changes to the saved channel of the selected zone. If there is no saved channel in the
selected zone, the radio defaults to the first channel in the zone.
Zone Display
Each zone has a zone name. The zone name is displayed when selecting a zone using the
ZONE menu.
With a one‐line display it is not possible to show the channel name and zone name at the
same time. The main screen normally displays the channel name.
If a key is assigned to the ZONE function, then pressing that key will display the current
zone. The radio changes to the zone select menu with the current zone as the starting
point. Pressing the ZONE key again or pressing the BACK key cancels the zone select menu.
If no key is pressed, a timeout will clear the zone menu and return the radio to the main
screen. By this mean the user can check what the current zone is by a key press at any time,
but the zone name is not normally displayed.
Zones and Recall Channels
A recall channel is a channel assigned to a RECALL key. The channel assigned to a RECALL
key is not necessarily in the current zone. When the RECALL key is pressed, the radio
changes to the recall channel. By default the radio changes to the zone the recall channel is
in, (although this is optional), therefore the next channel change using the SEL knob will be
from the recall channel's zone.
Alternatively the radio can be configured to remain in the current zone while on the recall
channel frequency or talk group. In this case the next channel change using the SEL knob
will be from channels in the current zone.
15
Zones and Scanning
There are two main types of scanning; scan groups and zone scan. The scan behavior when
zones are changed depends on the current scan type in progress.
A scan group is a list of channels used for scanning or voting. The scan group appears in the
channel list, and is selected by the user with the SEL knob.
If the radio is currently on a scan group channel, scanning stops when the zone is changed.
If the initial channel in the selected zone is a scan group, then scanning resumes with that
scan group.
Zone scan gives the user the ability to scan selected channels in the current zone. Channels
to be included in the scan are tagged. Zone scan is started and stopped with the SCAN key.
If zone scan is active when zones are changed then zone scan continues to be active in the
selected zone if that zone has channels tagged for zone scan. If zone scan is not possible in
the selected zone, (e.g. there are insufficient tagged channels) then scan stops and the radio
changes to the initial channel in the zone.
Channels in a scan group are not necessarily from the current zone. While scanning the
radio remains in the current zone as it changes channels in the scan group. If a signal is
received or PTT is pressed so the radio holds on a channel in the scan group, the radio
remains in the current zone. If the user exits scan while holding on a channel in the scan
group the radio may change to the zone of the hold channel or optionally remain in the
current zone.
Zone Editing
Zones can be created, modified and deleted using the Radio programmer only. Zones cannot
be modified by the user.
If zones are enabled, there must be at least one zone in the radio. If there is only one zone,
then all channels in the radio will be in that zone.
A zone must contain at least one channel for that zone to be enabled.
If no zone name is specified the radio generates a zone name: ZONE 1, ZONE 2 etc.
A zone can be disabled with the radio programmer. A disabled zone cannot be selected by
the user in the radio, however, the zone and its channels will still exist in the memory.
A zone is deleted when all channels in that zone are also deleted or moved from that zone.
If the zone contains channels that are members of a scan group that is in another zone, then
16
the zone cannot be deleted until the channel is removed from the scan group. When a zone
is deleted, the zone name is erased and all zone flags are cleared.
Every channel has to belong to a zone. Channels can be moved from one zone to another in
the programmer.
SCAN
The scan feature is used to monitor a group of channels for activity. When there is activity
on a channel the radio stops scanning and holds on that channel.
A scan group can only contain Analog or P25 channels. The scan group cannot include
another scan group or a P25 Trunking channel. The channels in the scan group do not have
to be from the same zone as the scan group. Channels in the scan group may be hidden
channels, or channels that can normally be selected. A scan group can contain up to 32
channels.
There are two ways that channels can be grouped for scanning or voting:
Scan Group
Zone Scan
Scan Group
A scan group is a list of channels used for scanning or voting. The main use for a scan group
is to define a channel that performs RSSI voting of repeater frequencies. However, scan
groups can be configured for different types of scanning or voting.
A scan group appears in the channel list and is selected using the SEL knob. The name of the
scan group appears as a channel name; therefore a scan group appears to be another
channel to the user. If zones are enabled, a scan group has to belong to a zone. A scan
group can only belong to one zone. Several scan groups can be included in one zone.
Scanning or voting begins automatically when the scan group is selected. Scanning or voting
stops when the scan group is deselected.
While there is no channel activity and the scan group is scanning, the scan group name is
displayed. When channel activity is detected, the display may show the name of the channel
the radio is holding on. When channel activity ceases and the radio resumes scanning or
voting, the scan group name is displayed again.
A scan group can be assigned to a RECALL key. When the RECALL is pressed while on
another channel, the radio selects the scan group and scanning or voting begins
immediately. If a RECALL key assigned to another channel or scan group is pressed while a
17
scan group is active, then the scan group is deselected and scanning or voting stops. The
radio then selects the channel or scan group assigned the RECALL key.
A scan group is configured using the radio programmer. The scan group configuration
cannot be modified and channels cannot be added to or removed from the scan group by
the user.
A scan group can be configured for either scanning or voting. Each scan group can be
configured individually.
Scanning
Scanning is generally used to monitor a group of unrelated channels for activity. The radio
checks each channel in the scan group in turn for activity and holds on the first channel with
a valid signal. The conditions to hold on a channel are the same as the general un‐mute
conditions of the radio.
When the signal disappears the radio continues to hold on the channel until the scan hold
timeout expires. If the scan hold timeout expires, the radio resumes scanning.
Open Scan
In Open Scan, the radio scans the channels in the sequence of the channel list checking for
activity.
If the PTT is pressed while holding on a channel, the radio transmits on the hold channel and
the scan transmit channel is set to the hold channel. When the PTT is pressed while
scanning, the radio transmits on the scan transmit channel.
Priority Scan
In Priority Scan, the radio scans the channels in sequence similar to open scan but checks a
priority channel more often than the other channels. The first channel in the scan group is
the priority channel.
If the PTT is pressed while holding on a channel, the radio transmits on the hold channel.
When the PTT is pressed while scanning, the radio transmits on the priority channel.
VOTING
Voting is generally used to monitor a group of channels associated with a repeater network.
There are two general types of voting, RSSI voting and Busy Voting.
RSSI Voting
RSSI voting (also called Signal Strength voting) is used with repeater networks where the
repeaters transmit the same information simultaneously on different repeater frequencies.
18
The radio scans the repeater output frequencies and selects the channel with the highest
signal strength or the first channel above a signal strength threshold.
The radio maintains a channel to use for PTT. Generally this is the last channel the radio
selected for receive. If no signal has been received the radio will cycle through all the
channels in turn on each PTT press.
Busy Voting
Busy voting is used when there are several repeaters on the same site providing a pool of
channels to several groups of users. Each group of users is generally defined by a common
CTCSS tone. The radio scans the channels and keeps track of which channels are free and
which are busy and currently used by another group.
When a signal is received with the correct CTCSS tone, the radio stops scanning and holds
on that channel.
When the PTT is pressed the radio transmits on a free repeater channel. The radios in a
group don't transmit on the same repeater channel each time, as it depends on which
repeater channel is in use at any given time.
Zone Scan
Zone scan is used to scan a group of channels for activity within the current zone. The
channels are scanned in sequence for activity using open scan or priority scan methods.
Voting is not used for zone scan.
The channels to be scanned are tagged for zone scan. Analog channels, P25 Conventional
channels, and scan groups can be tagged for zone scan. If a scan group is tagged, then only
the first channel in the scan group is included in the zone scan sequence. P25 Trunking
channels cannot be tagged. Hidden channels can also be tagged. Hidden channels can only
be tagged by the radio programmer, not by the user.
Zone scan channels are tagged using the radio programmer. The user may also optionally
be enabled to tag channels for zone scan. To tag a channel, the user selects the channel
with the SEL knob then tags the channel with a long press of the SCAN key. A tagged
channel is untagged with a long press of the SCAN key.
Zone scan is selected using the SCAN key. When the SCAN key is pressed, the radio
commences scanning all the tagged channels in the current zone. The SCAN key is pressed
again to stop zone scan. While zone scan is active the SEL knob cannot be used to select
channels.
If a RECALL key is pressed during zone scan, then zone scan stops and the radio selects the
channel or scan group assigned to the RECALL key.
19
If a different zone is selected while zone scan is active, then zone scan continues to be active
in the selected zone if possible. If there are not enough channels tagged for zone scan in the
selected zone, then zone scan stops.
If the SCAN key is pressed while a scan group is selected (i.e.: an RSSI voting channel), the
radio stops the scan group activity and commences the zone scan. When the SCAN key is
pressed again, the zone scan stops and the radio will resume scan group activity.
During zone scan, the display changes through the zone scan channels. When activity is
detected on a channel, the radio holds on the channel and the display shows the name of
the hold channel.
The current channel may be included in the zone scan channel list even if it is not tagged.
SCAN NUISANCE DELETE
A nuisance channel is one where temporary unwanted noise or interference constantly
stops the scan. A nuisance channel can be temporarily removed by turning the SEL knob
while holding on the channel. The radio will resume scanning and the nuisance channel will
be removed for a fixed time (typically 2 minutes).
A nuisance channel can also be removed from the scan sequence by a long pres of the SCAN
key while holding on the channel. The radio will resume scanning and the nuisance channel
will be removed as long as zone scan is active.
DYNAMIC REGROUPING
Dynamic regrouping allows the network or dispatcher to re‐assign the radio to a special
communications talk group. When operating on this group, normal channel change
operation may be disabled.
Dynamic regrouping is only available on P25 trunking channels.
To activate dynamic regrouping, the operator sends a ‘Dynamic Regroup Request’ to the
P25 network.
To send a Dynamic Regroup request:
1. Press the SEL knob to access the menu.
2. Rotate the SEL knob to select ‘TRUNKING’ then press the SEL knob.
3. Rotate the SEL knob to select ‘DYN REGROUP’ then press the SEL knob to send the
request.
4. The display will show ‘SEND REQ’.
If the request is successful the display shows an acknowledgement. The request may not
succeed for various reasons.
20
Dynamic regrouping is de‐activated by either selecting another talk group/channel (if
possible), or by send a request to de‐activate dynamic regrouping. When deactivated, the
radio will return to the talk group that was active when the dynamic regroup request was
sent.
Dynamic regrouping is not preserved between power off‐on.
FAILSOFT OPERATION
If the radio is unable to access the trunking system, it can be programmed to enter failsoft
mode. In failsoft mode the radio switches to a programmed conventional P25 or analog
channel.
Failsoft mode is entered when either a trunking channel is selected and the radio fails to
register with the trunking controller, or the radio loses communications with the trunking
controller.
INSTALLATION
The CM1039 is supplied with a slim, slide‐on mounting cradle. The cradle can be screwed or
bolted in any convenient location in your vehicle (under or above the dash, on the centre
console, etc) using the mounting slots provided in the base. The CM1039 contains a built‐in
speaker and can be installed with the speaker facing upwards or downwards to ensure the
receiver audio is projected clearly. Alternatively, the CM1039 can be fitted with an
extension speaker if required. When installing the radio, avoid mounting it close to heaters
or air conditioners. Screw the mounting cradle to a firm surface. Slide the CM1039 into the
cradle from the front until it clicks into place. Finally, plug the power and antenna leads to
the sockets provided on the rear of the radio.
Mounting the Cradle
21
Fitting the Radio
Removing the Radio
Gently
spread
tabs
Gently
spread
tabs
Slide radio from
cradle
Fitting MC513BC Microphone
Screw the microphone mounting clip to a firm surface.
The microphone uses a miniature 6 pin telephone style plug and socket.
To fit the microphone:
1. Position the microphone plug so the plastic tab faces downwards. Press the plug into
the socket until it ‘clicks’.
2. Gently press the rubber strain relief into the hole surrounding the socket so that the
slot around the strain relief fits neatly inside the lip of the hole.
22
Note: The microphone can also be connected to the microphone socket on the rear panel
or alternatively two microphones can be connected using both sockets. In this case the
first microphone that keys the PTT takes priority.
Removing the microphone
1. Squeeze the rubber strain relief near the front panel to disengage the slot, and slide
the strain relief back along the microphone cord.
2. Squeeze the plastic tab on the microphone plug towards the plug to unlock it while
gently pulling the plug outwards.
If the plug does not come out easily, the tab has not released correctly and should be
squeezed again.
Console Mounting the CM1039 Series
For console mounting, a flush mounting DIN Adaptor MBD001 is available as an optional
accessory. The adaptor includes mounting brackets and a specially designed front panel
escutcheon to suit most vehicle installations.
Installation instructions are provided with the bracket. See your nearest GME retailer for
details.
Din Adaptor MBD001
23
DC POWER CONECTION
The CM1039 is designed for 13.8 Volt DC, negative earth installations only (i.e. where the
negative terminal of the battery is connected to the chassis or frame of the vehicle).
Two in‐line 10 Amp fuses are supplied. These fuses are to be connected as close to the
battery as possible. The radio’s positive (red) lead should be connected via a 10 Amp fuse
directly to the battery’s positive terminal. Connect the radio’s negative (black) lead via a 10
Amp fuse directly to the battery’s negative terminal.
ANTENNA INSTALLATION
To comply with FCC exposure limits the radio must be installed using an externally mounted
antenna with a gain of either 2.15 dBi or 5.15 dBi. For best results your antenna should be
professionally installed using industry standard techniques.
Transmit only when bystanders are at a minimum safe distance of 35 inches (0.9 m) from
the antenna.
24
SPECIFICATIONS
GENERAL
RF Performance:
Frequency Band:
RF Switching Bandwidth:
Number of channels:
Channel Steps:
Frequency Stability:
Operating Voltage Range:
Current Consumption:
Compliant with AS/NZS 4295, ETSI EN 300-086-2, ETSI EN 300-113-2, TIA-603-C,
FCC Parts 90/15, IC - RSS119
VHF 136 to 174 MHz, UHF Lo 403 to 470 MHz, UHF Hi 450 to 512 MHz
VHF 38 MHz, UHF 70 MHz
1072
12.5 kHz, 6.26 kHz, 5 kHz, 2.5 kHz
+/-1 kHz for 14°F (-10°C) to +140°F (60°C)
10.8V to 15.6V
RX muted: 170 mA, RX full audio: 0.8A, TX: 5.0A (VHF) 6.0A (UHF)
TRANSMITTER
RF Output:
Transmit Duty Cycle:
Modulation:
Deviation Limiting:
TX Audio Frequency
Response:
AF Distortion:
TX Audio Residual Noise
and Hum:
Spurious Emissions:
Adjacent Channel Power:
25W, 10W, 5W, 1W selectable per channel
4:1 for 25W output
FM, DC coupled, DSP audio processing
2.5 kHz at +20 dB AF limiting
+6 dB/octave, +1dB/-3dB, 300 Hz to 3 kHz
3% below limiting
-40 dB
-36 dBm
-60 dBc
RECEIVER
Circuit Type:
Sensitivity
Adjacent Channel
Selectivity:
Spurious Rejection:
Intermodulation Rejection:
Blocking
Conducted Spurious
Emissions:
Double Conversion Superheterodyne DC Coupled, DSP audio processing
-122 dBm for 12 dB SINAD unweighted
60 dB
75 dB
75 dB
100 dB
-80 dBm
AUDIO
RX Audio Frequency
Response:
RX Audio Residual Noise
and Hum:
Audio Rated Power:
-6 dB/octave, +1/-3 dB, 300 Hz to 3k Hz
-40 dB
3W into 4 Ohms
MECHANICAL
Dimensions:
Weight
1.14” (29 mm) x 5” (127 mm) x 6.4” (163 mm)
22oz (620 g)
ENVIRONMENTAL
Operating Temperature
Range:
Shock and Vibration:
14°F (-10°C) to +140°F (60°C)
MIL SPEC 810
Specifications are subject to change without notice or obligation
25
WARRANTY – North America
Standard Communications Pty Ltd (herein, GME) warrants each new radio product manufactured or
supplied by it to be free from defects in material and workmanship under normal use and service for a
period listed below, provided that the user has complied with the requirements stated herein.
The Warranty period begins on the date of purchase from an authorized GME Sales and Service
Outlet. This warranty is offered to the original end user and is not assignable or transferable. GME is
not responsible for any ancillary equipment attached to or used in conjunction with its products.
GME offers to the original end user a Two (2) Year Limited Warranty on the CM1039 Series
Commercial Radio product range. During this period, if the product fails to function under normal use
through manufacturing defect(s) or substandard workmanship, it should be returned to the authorized
GME Sales and Service Outlet from which it was purchased. The Sales and Service Outlet will repair
the product or return the product for repair to GME or its authorized Regional Repair Depot. The user
is responsible for the payment of any charges or expenses incurred for the removal of the defective
product from the vehicle or other location of its use; for the transportation of the product to the Sales
and Service Outlet; for the return of the repaired / replacement product to the location of its use and
for the reinstallation of the product.
GME shall have no obligation to make repairs or to provide replacement product, which results from
normal wear and tear or is necessitated in whole or in part by catastrophe, fault or negligence of the
user, improper or unauthorized alterations or repairs to the product, incorrect wiring, use of the
product in a manner for which it was not designed or by causes external to the product.
This Warranty is void if the product serial number is altered, defaced or removed.
GME’s sole obligation hereunder shall be to replace or repair the product covered in this warranty.
Replacement, at GME’s discretion, may include a similar or higher-featured product.
Repair may include the replacement of parts or boards with functionally equivalent reconditioned or
new parts and/or boards.
No repair undertaken or replacement product provided during the warranty period will renew or extend
the warranty period past the period from the original date of purchase. All replaced parts, electronic
components or boards become the property of GME.
THE EXPRESS WARRANTIES CONTAINED HEREIN ARE IN LIEU OF ALL OTHER
WARRANTIES, EITHER EXPRESSED OR IMPLIED OR STATUTORY, INCLUDING, WITHOUT
LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.
FOR ANY PRODUCT WHICH DOES NOT COMPLY WITH THE WARRANTY SPECIFIED, THE
SOLE REMEDY WILL BE REPAIR OR REPLACEMENT. IN NO EVENT WILL GME BE LIABLE TO
THE BUYER OR ITS CUSTOMERS FOR ANY DAMAGES, INCLUDING ANY SPECIAL,
INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES, OR FOR THE LOSS OF PROFIT,
REVENUE OR DATA ARISING OUT OF THE USE OF OR THE INABILITY TO USE THE
PRODUCT.
This warranty is void for sales and deliveries outside of the U. S. A. and Canada.
Rev D
26

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : ianlind
Create Date                     : 2014:07:18 16:44:23+10:00
Modify Date                     : 2014:07:18 16:49:10+10:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2014:07:18 16:49:10+10:00
Format                          : application/pdf
Title                           : Microsoft Word - CM1039 USA Instruction Manual Rev_D.docx
Creator                         : ianlind
Document ID                     : uuid:0a1b5c00-d603-42c0-991d-89a45a739b74
Instance ID                     : uuid:f234b888-efcf-43a3-97de-8edd6b7946cf
Page Count                      : 26
EXIF Metadata provided by EXIF.tools
FCC ID Filing: TXJCM1039V

Navigation menu