Sun Communications DECT64-S96-B11 US DECT PHONE- BASE User Manual SunCorp Generic GAP Specification
SunCorp Communications Limited US DECT PHONE- BASE SunCorp Generic GAP Specification
USERS MANUAL
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 746737 |
| Application ID | 54gV9oGcpsJh3YZ3bR5Z9w== |
| Document Description | USERS MANUAL |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 42.91kB (536336 bits) |
| Date Submitted | 2007-01-12 00:00:00 |
| Date Available | 2007-01-15 00:00:00 |
| Creation Date | 2006-06-02 18:41:18 |
| Producing Software | Acrobat Distiller 6.0 (Windows) |
| Document Lastmod | 2006-08-21 13:37:24 |
| Document Title | SunCorp Generic GAP Specification |
| Document Creator | Acrobat PDFMaker 6.0 Word 版 |
| Document Author: | Wing |
DECT 64-S96+B11 GAP MMI Specification Document Version 1.0 1 of 40 FCC Interference Information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation. device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the interference. • Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna. • Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna is connected. FCC INTERFERENCE INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital FCC RF Radiation Exposure Statement The installation of the base unit should allow at least 20 centimeter between the base and persons in compliance with FCC RF exposure guidelines. For body worn operation, the portable part (handset) has been tested and meets FCC RF exposure guidelines. This device must not be co-located or operating in conjunction with any other antenna or transmitter.The changes or modifications not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment. FCC Part 15.19 FCC Part 15.21 FCC Part 15.105(b) FCC Part 2.1091 FCC Part 2.1093 C ongratulations on your selection of this quality product by XACT Communication. With proper care and adherence to the set-up and user instructions in this Owner's Manual, this unit will provide you with years of trouble-free service. XACT is committed to providing quality products that fit your needs.We would like to have any comments or suggestions you might have on this product.You may mail your comments to: XACT Communication, LLC 105 Madison Avenue New York, NY 10016 info@xactcommunication.com WHAT’S IN THE BOX? User manual Edge 1.4 handset Edge 1.4 base station Line cord Power adapter for base station Battery door 2 x AAA rechargeable batteries Warranty information In the event that any item is missing or if you find any mismatch or damage, promptly contact your retailer. Revision History Revision document DECT 10 Version 1.0 Author Date Comments Yamada 17 Jan. 05 Initial document for DECT 10 Version 1.1 Yamada 28 Jan. 05 Add two redial digits limit Change the LCD dots to 5 X 8 from 5 X 7 Add DECT 24 Add KPN operation detail Add DECT 15 option for handset VMWI handling Change back the arrow icon to be LEFT and RIGHT Version 1.2 Yamada 01 Feb. 05 Change the CID display and add the EEPROM setting for display word. Add the VMWI indication option on the base LED. Change to user programmable for two direct access button Version 1.3 Yamada 02 Feb. 05 Modify the operation for VMWI Add the month and date setting on the menu Short press “R” key to indicate DD / MM for 3 seconds. Version 1.4 Yamada 02 Mar. 05 Change the H/S ringer melody to 10 from 5. Change the H/S ringer volume to 5 from 3. 4 Poly tone Ringer for handset. Add EEPROM setting option for Power ON/OFF function enable disable. Add RPAS enable/disable menu inside base setting menu. Add more for default setting Add Handfree mode speaker volume control. Version 1.5 Yamada 11 Mar. 05 Change the text input character table and changing the case method. Version 1.6 Yamada 03 May 2005 Version 1.7 Yamada 17 May 2005 Add the Date setting menu operation. Add more explanation for Re-dial size limit Add frequency changing option for Latin American Change the two Hot key operation Version 1.8 Yamada 14 July 2005 Change the phonebook size (20 digits -> 24 digits) Change the VMWI icon and TAM icon. Change the alarm icon turn off timing. Change the flashing rate for base VMWI LED indication. (DECT 20 base option) Add the option for un-read SMS message indication on the base unit. (DECT20 base option) Version 1.0 for DECT 64 Yamada 04 May 2006 Change to DECT 64 MMI document 2 of 40 Contents FEATURES OF SUNCORP GAP DECT .............................................................. 6 1.1 Purpose of this document ......................................................................................................... 6 1.2 General features ......................................................................................................................... 6 1.3 Handset description ................................................................................................................... 7 1.3.1 Handset keypad..................................................................................................................... 7 1.3.2 LCD display ........................................................................................................................... 9 1.3.3 Standby display ................................................................................................................... 10 1.3.4 LED...................................................................................................................................... 10 1.3.5 Tones................................................................................................................................... 10 1.4 Base description....................................................................................................................... 11 1.4.1 Page Key ............................................................................................................................. 11 1.4.2 LED...................................................................................................................................... 11 1.4.3 Tones................................................................................................................................... 12 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 2.14 MAIN USER INTERFACE .................................................................................. 12 Power up.................................................................................................................................... 12 Standby mode ........................................................................................................................... 12 TALK mode................................................................................................................................ 13 Intercom mode .......................................................................................................................... 13 Incoming call mode .................................................................................................................. 13 MENU mode............................................................................................................................... 13 Phonebook mode...................................................................................................................... 13 SMS ............................................................................................................................................ 13 Voice Mail .................................................................................................................................. 13 Redial list mode..................................................................................................................... 14 CLIP mode ............................................................................................................................. 14 Charging mode...................................................................................................................... 14 Busy mode............................................................................................................................. 14 Power down ........................................................................................................................... 14 CALL USER INTERFACE.................................................................................. 15 3.1 Incoming call............................................................................................................................. 15 3.1.1 To answer the call: .............................................................................................................. 15 3.2 External outgoing call .............................................................................................................. 15 3.2.1 Dialling PAUSE.................................................................................................................... 16 3.2.2 Flash key ............................................................................................................................. 16 3.2.3 DTMF dialling ...................................................................................................................... 16 3.2.4 Pulse dialling ....................................................................................................................... 16 3.2.5 Temporary DTMF dialling.................................................................................................... 16 3.2.6 Dial tone detection............................................................................................................... 16 3.2.7 Call timer display ................................................................................................................. 16 3.2.8 Mute..................................................................................................................................... 16 3.2.9 Changing Earpiece Volume during Call .............................................................................. 16 3.3 Direct access memory ............................................................................................................. 17 3.3.1 How to access the direct memory dial number during idle.................................................. 17 3.3.2 During OFF HOOK .............................................................................................................. 17 3.3.3 Direct access dial data ........................................................................................................ 17 3.4 Redial feature ............................................................................................................................ 17 3.4.1 Limit for number of redial digits ........................................................................................... 17 3.4.2 Redial list ............................................................................................................................. 17 3.4.3 Dial out redial after OFF HOOK .......................................................................................... 18 3.4.4 Delete a redial buffer : ......................................................................................................... 18 3.4.5 Delete all redial buffer : ....................................................................................................... 18 3.4.6 Store a Redial list into PHONEBOOK ................................................................................. 19 3 of 40 3.5 Internal call transfer ................................................................................................................. 19 3.6 Conference call between two handset and external caller .................................................. 19 3.7 Caller ID (CLIP) features .......................................................................................................... 19 3.7.1 General features.................................................................................................................. 19 3.7.2 Caller ID display .................................................................................................................. 19 3.7.3 VMWI indication................................................................................................................... 21 3.7.4 Recall CLIP list .................................................................................................................... 21 3.7.5 Delete one CLIP list............................................................................................................. 22 3.7.6 Delete all CLIP list ............................................................................................................... 22 3.7.7 Store a CLIP list into PHONEBOOK ................................................................................... 22 3.7.8 Dial out CLIP list .................................................................................................................. 22 3.7.9 KPN specification handling.................................................................................................. 22 3.8 Phonebook ................................................................................................................................ 23 3.8.1 Dial a number of the phonebook list.................................................................................... 23 3.8.2 See the dial number of the phonebook list during Talk. ...................................................... 24 3.9 Intercom..................................................................................................................................... 24 3.9.1 Internal call .......................................................................................................................... 24 3.9.2 End of intercom call............................................................................................................. 24 3.9.3 Intercom mode..................................................................................................................... 24 3.9.4 End of intercom ................................................................................................................... 24 3.10 Page button ........................................................................................................................... 24 3.11 Battery and charge management ........................................................................................ 25 3.11.1 Battery indicator................................................................................................................... 25 3.11.2 Low battery conditions......................................................................................................... 25 3.11.3 Charge conditions................................................................................................................ 25 3.11.4 Start-up with low batteries ................................................................................................... 25 3.12 Range indication ................................................................................................................... 26 3.12.1 Out of range tone................................................................................................................. 26 3.12.2 In range tone ....................................................................................................................... 26 3.12.3 Range limit tone during a call .............................................................................................. 26 3.13 Clock and Alarm clock ......................................................................................................... 26 3.13.1 Clock.................................................................................................................................... 26 3.14 Alarm activation .................................................................................................................... 26 3.14.1 During idle ........................................................................................................................... 26 3.14.2 During Talk .......................................................................................................................... 26 3.14.3 During ringing or paging ...................................................................................................... 27 MENU SETTINGS .............................................................................................. 28 4.1 PHONEBOOK ............................................................................................................................ 29 4.1.1 Add a name ......................................................................................................................... 29 4.1.2 Delete a name ..................................................................................................................... 31 4.1.3 Modify a name or number ................................................................................................... 31 4.1.4 Change the character case ................................................................................................. 31 4.2 SETUP........................................................................................................................................ 31 4.2.1 BASE VOL........................................................................................................................... 31 4.2.2 BASE MEL........................................................................................................................... 31 4.2.3 DEL HS................................................................................................................................ 31 4.2.4 PIN CODE ........................................................................................................................... 32 4.2.5 Dial mode selection (This mode will not appear when set the Pulse dialling disable by EEPROM) .......................................................................................................................................... 32 4.2.6 Recall duration selection ..................................................................................................... 32 4.2.7 Default settings.................................................................................................................... 32 4.3 HANDSET .................................................................................................................................. 33 4.3.1 BEEP ................................................................................................................................... 33 4.3.1.1 KEYTONE ........................................................................................................................... 33 4.3.1.2 LOW BATTERY................................................................................................................... 33 4.3.1.3 OUTRANGE ........................................................................................................................ 33 4.3.2 INT RING VOL..................................................................................................................... 33 4.3.3 EXT RING VOL ................................................................................................................... 33 4.3.4 INT MELODY....................................................................................................................... 33 4 of 40 4.3.5 EXT MELODY ..................................................................................................................... 34 4.3.6 DATE AND TIME................................................................................................................. 34 4.3.7 ALARM SET ........................................................................................................................ 34 4.3.8 AUTO ANSWER.................................................................................................................. 34 4.3.9 NAME .................................................................................................................................. 34 4.3.10 KEY LOCK........................................................................................................................... 35 4.3.10.1 Quick KEY LOCK ................................................................................................................ 35 4.3.10.2 To unlock key: ..................................................................................................................... 35 4.4 REGISTER ................................................................................................................................. 35 4.4.1 SELECT BASE .................................................................................................................... 35 4.4.2 REG BASE .......................................................................................................................... 35 5.1 5.2 5.3 PREFIX DIALLING............................................................................................. 36 Detect string.............................................................................................................................. 36 Replace string ........................................................................................................................... 36 Detecting and replacement...................................................................................................... 36 DECT 24 ADDENDUM (SET THE EEPROM SETTING FOR DECT 24) ........... 37 6.1 Change to Handset keypad layout.......................................................................................... 37 6.1.1 LCD display ......................................................................................................................... 38 QUICK DEFAULT SETTINGS ........................................................................... 39 SUBSCRIBE A NEW HANDSET ....................................................................... 39 TEST MODES .................................................................................................... 39 9.1 9.2 Handset test modes.................................................................................................................. 39 Base unit test modes ............................................................................................................... 39 10 SPECIFICATIONS........................................................................................... 40 10.1 10.2 CLIP Standards ..................................................................................................................... 40 DECT Specifications............................................................................................................. 40 5 of 40 1 1.1 Features of SunCorp GAP DECT Purpose of this document The purpose of this document is to describe the specifications and the MMI of the product. It includes information about : • Hardware and software features • User interface description • User settings 1.2 General features General features Phonebook of 50 entries Search by name 20 last numbers redial Different melody for internal and external calls Automatic answering when taking the handset from the base Automatic phone off when placing the handset on cradle Mute key Pre-dialling Dialling mode changing during conversation User friendly menu Display length of conversation Sixteen languages PIN code for set-up Page function Select earpiece volume (Total 5 step) Select ringer volume (Total 5 steps) 10 different melodies for handset 4 poly tone ringer for handset 5 different melody for base Out of range tone Battery warning tone Customisable name of each handset 5 Portable Parts per base 4 Fixed Parts per handset Clock on the handset Alarm clock on the handset 3-Way conference call *Caller ID Type I & II *CLIP type I & II FSK (ETSI) & DTMF (KPN) * Bellcore CLIP Display caller name* List of last 40 calls Time stamped calls Redial last outgoing number Display caller number during conversation Two maximum digits limit for last number redial The handset has compatibility for DECT 65 (Auto detect) Intercom Free intercom between handsets Transfer a call to another handset Option functions (Set by EEPROM) Two direct access keys Prefix dialling number Power ON/OFF function Frequency option for DECT 6.0 and Euro DECT Hardware option Backlight LCD Backlight key board LED for Talk and incoming ring Line reverse detection for KPN** (Option) **VMWI indication *Only if the function is supported by the network and type II is option ** Only if the function is supported by the network 6 of 40 1.3 Handset description 1.3.1 Handset keypad Some keys have more than one usage depending on the MMI state (standby, in call, menu mode). The table hereafter gives all the possible actions for each key. In the following chapters, the reference for one key will be indicated with the main action of the key. Sometimes the second (or third) meaning will be indicated as follows: KEY_USE1/KEY_USE2. Key name Standby mode KEY_MENU/OK Enter menu Incoming call Talk mode From incoming call Outgoing call Menu mode Phoneboo k mode Confirm Confirm MENU KEY_LNR Redial/Pause Enter Redial list Pause Redial (first key in call) Pause (after first key) Pause KEY_UP/CLIP ▲ Enter CLIP list Ringer volume up Receiver Volume Up Receiver Volume Up Choose Choose KEY_DOWN/CLIP ▼ Enter CLIP list Ringer volume down Receiver Volume Down Receiver Volume Down Choose Choose KEY_MEM/EXIT Enter Phonebook Enter Phonebook KEY_CLEAR Toggle Mute Toggle Mute Standby mode Standby mode Exit Exit Clear Clear KEY_HOOK Go in TALK mode KEY_INT Intercom Transfer the call Transfer the call Power off (hold) Flash Flash Dial 0 Dial 0 Pre-dial 1 (DDK1:Long) Dial 1 Dial 1 Pre-dial 2 (DDK2:Long) Dial 2 Dial 2 Pre-dial 3 Dial 3 Dial 3 Pre-dial 4 Dial 4 Dial 4 Go in TALK mode Int KEY_R/POWER KEY_0 Change to DD / MM display for 3 seconds (Short press) Pre-dial 0 KEY_1 KEY_2 KEY_3 KEY_4 7 of 40 KEY_5 Pre-dial 5 Dial 5 Dial 5 Pre-dial 6 Dial 6 Dial 6 Pre-dial 7 Dial 7 Dial 7 Pre-dial 8 Dial 8 Dial 8 Pre-dial 9 Dial 9 Dial 9 Pre-dial * Dial * Go into DTMF mode from pulse Dial * Go into DTMF mode from pulse KEY_6 KEY_7 KEY_8 KEY_9 KEY_STAR KEY_HASH/LOCK Pre-dial # Toggle key lock (Hold) Short press is less than 1 second Long press is more than 1.5 second Hold is press and hold more than 3 seconds 8 of 40 1.3.2 LCD display The LCD display is composed of 12 characters dots matrix form (8 X 5 matrix), 4 characters 7 segments and 18 icons. (Icon drawings are just reference only. Plesae refere to the LCD specification) The definition of the icons is as follows: (Icons are just reference only) Icon NAME Definition HOOK_IND Off hook indicator EXT EXT External call engaged INT INT Internal call engaged NEW_CLIP_IND Caller identification available /new numbers in calls list CLIP_ANSWERED Indicate answered call CLIP_UNANSWER Indicate unanswered call ED PHONEBOOK_IND Phonebook indicator MENU_IND Menu indicator BATTERY 3 levels battery indicator 1 segment: weak, 2 segments: medium, 3 segments: full The segments scroll during battery recharging and stop scrolling when battery is full Handset keypad locked LOCK_IND TAM_MSG Signal strength indicator. The icon is steady when handset is locked to its base The icon flashes when the handset is unlocked or not subscribed to any base Indicates that displayed number or message is longer than the screen (12 digits) Indicates that displayed number or message is longer than the screen (12 digits) VMWI indication NEW_SMS_IND New SMS message indication VMWI_IND This is for DECT 65 ANTENNA LEFT_ARROW RIGHT_ARROW 9 of 40 HAND_FREE Hand free indicator. This is for DECT 10-SP ALARM_SET Alarm set indicator 1.3.3 Standby display In standby mode, the display shows the handset name (Maximum 10 characters) and the handset number (Last 1 digit). Also, the current time on the Time display (24 hours indication) 1.3.4 LED • Talk LED Action Standby mode Subscription mode In call Incoming call New CID New SMS Voice mail notification LED state OFF Flash Flash Flash synchronized with PSTN ring pattern. OFF Flash (Not for DECT 6.0) Flash • Key backlight LED (Hardware Option) Action LED state Standby mode (No key OFF press) Press any key ON for 8 seconds after press last key (Setting by EEPROM) During key lock OFF Incoming call Flash (0.5s ON/OFF) External call ON External call on hold Flash (0.5s ON/OFF) • LCD backlight LED and Key backlight LED (Hardware Option) Action LED state Standby mode (No key OFF press) Press any key ON for 8 seconds after press last key (Setting by EEPROM) During key lock OFF Incoming call ON 1.3.5 Tones Nr Name Ring 1 Ring 2 Ring 3 Ring 4 Ring 5 Ring 6 Ring 7 Ring 8 Ring 9 10 of 40 10 Ring 10 TONE_CONFIRM TONE_LOW_BATT 10 TONE_FREE 11 TONE_CALL_WAITING 12 TONE_BUSY 13 TONE_ERROR 14 TONE_IN_RANGE 15 TONE_WARNING 16 TONE_OFF_HOOK_WARNING 17 TONE_RING_BACK 18 TONE_ALARM_CLOCK 1.4 Base description 1.4.1 Page Key Key action Short press (<5 s) Long Press (>=5s) MMI action Send a page to handsets Enters subscription mode (in use LED will flash) 1.4.2 LED Power/In use LED Action Standby mode Subscription mode In call Incoming call New SMS message LED state ON Flash Flash Flash synchronized with PSTN ring pattern. Flash (Not for DECT 6.0) ### Add the EEPROM setting (FP) to enable the VMWI indication on the base unit. Especially for Australia, it is better to have VMWI on the base unit. It should enable or disable this function by EEPROM setting. (If there is not only one Voice mail server, this function shall be disabled by EEPROM setting) Operation: Receive the CID data (Parameter type 0Bh + Data FFh), and then activate the base IN-USE LED to be flash. The Flashing rate is 0.2S - 0.25S ON/OFF This Flashing is lower priority, so, any other operation to turn ON the IN-USE LED, those operation have priority. The Flashing is keeping until received the CID data (Parameter type 0Bh + Data 00h) regardless the unit goes to oh-hook or off-hook. 11 of 40 - The VMWI signal may be contained Type 2 CID data. So, during Talk mode and received the (Parameter type 0Bh + Data FFh), the information will be kept and once the unit goes to standby, then the IN-USE LED starts to flash. 1.4.3 Tones The three base melodies are shown in the following table Nr Name Ring 1 Ring 2 Ring 3 Ring 4 Ring 5 TONE_CONFIRM Main User interface 2.1 Power up Plug the power supply into the base. The in use LED will be turned on and TONE_CONFIRM. Insert batteries in the handset. If battery level is enough (see Start up with low batteries chapter), the handset will start. The display will show “Base 1” and antenna flashing, until it locks onto its subscribed base. If the handset finds its base in the first 10 seconds, no beeps are played (see Range indication chapter). Then the display shows the standby display. 2.2 Standby mode In standby mode, the display shows the handset name and the handset number. The ANTENNA icon is steady. The BATTERY icon indicates the charge level. Handset: Events Press KEY_HOOK Press KEY_INT Press KEY_MENU Press KEY_MEM Press KEY_HASH /LOCK (hold 3 second) Press KEY_LNR/PAUSE Press KEY_UP/CLIP or KEY_DOWN/CLIP Press KEY_R/POWER (hold 3 second) Press 1,2,3……0,*,# Incoming call signal Another handset TALK Battery is low Battery is too low On charging Handset mode Enter TALK mode Enter intercom mode Enter MENU mode Enter phonebook mode Enter KEY LOCK mode Enter redial list mode Enter CLIP mode Enter power down mode Pre-dialling Incoming call mode Busy mode Battery low icon Power down mode Charging mode 12 of 40 Long press for 1 or 2 Access direct pre-programmed number Base: Events Press PAGE KEY Incoming call signal 2.3 Base mode Enter PAGE mode Incoming call mode TALK mode Refer to External outgoing call 2.4 Intercom mode Refer to intercom 2.5 Incoming call mode Refer to incoming call 2.6 MENU mode Refer to MENU settings 2.7 Phonebook mode Refer to phonebook 2.8 SMS Refer to SMS MMI document 2.9 Voice Mail An indication is given to user when voicemail is waiting, called the VMWI (Voice Mail Waiting Indication) VMWI notification/de-notification can be received from multiple voicemail server. Matching of VMWI notification/de-notification will be done using number field. On receipt of a VMWI “ON” message • The VMWI notification will be stored in to the CID list. • Each entry will show the CID of the voice mail server number, including box number if provided. • The name of the voice mail server, as sent in the “Name” field will also be stored in CID list along with the Date/Time of the call. The Name field can receive up to 50 characters, but the display will be truncated to 12 characters. • Note that no additional VMWI will be added to the list, if the server number is already existing on the CID list, but in this case the date and time shall be updated on the existing entry on the CID list. • • • icon will be flash. The Note that the CID list operate as a FIFO buffer. If the CID list is full, on receipt of a new notification, it will replace the oldest non-VMWI item in the CID list. (If oldest one is VMWI item, it shall not be erased) To access the voicemail server, the user can press KEY_TALK whilst the VMWI is displayed in the CID list. On receipt of a VMWI “OFF” message • If the -de-notification matches and item already on the CID list, then the notification will be removed from the list. 13 of 40 • If the item does not exist on the list, then the de-notification which has number will be ignored. However, if the • icon is flashing and received de-notification does not have number, and icon will be removed. there is no notification on the list, the When remove the notification and after remove the notification, if no other notifications are remain in the list, the icon will be removed. • When receive the VMWI notification without server number, the However, the notification shall not be stored to the call list. • When receive the VMWI de-notification without server number, the no notifications are in the list. Any kind of de-notification shall not be stored to call list. • • • icon shall start to flash. icon will be removed if icon, by a long press of “5”, whilst viewing CID The user can manually turn off the display of list. (It will effect to other handset and base also delete all the notification on the list) The user can manually remove VMWI notification from the CID list using delete function. When removed the notification and the notification was last one, the not effect to other handset and base) icon will be removed. (It will Note: • The VMWI data “0Bh + FFh or 00h” shall be received regardless Data link message such as “80h or 82h”. 2.10 Redial list mode Refer to redial features 2.11 CLIP mode Refer to Caller ID (CLIP) feature 2.12 Charging mode Refer to Charging conditions 2.13 Busy mode When one Handset is TALK, another handset’s “EXT” icon, and TONE_BUSY in earpiece if press KEY_HOOK 2.14 Power down Make a long press on KEY_R/POWER, and the handset power down. Press and hold KEY_R/POWER for 5 seconds to wake it up. When the handset wakes up, the clock time data shall be transferred from base. This function can be enable or disabled by EEPROM setting 14 of 40 3 3.1 Call User interface Incoming call The Phone should not ring when receiving a burst of notification. The network will send RPAS and caller ID in short period of time (at 4 seconds interval) Display The display shows "Call" on the 1st line and EXT icon blinks (0.5 s ON/OFF), if caller ID information is available (see 3.5), the caller name and number is displayed. The caller name is on the 1st line and number is on the 2nd line. (If the name is not available, only number is displayed on the 2nd line.) If the received number is match with Phonebook entry, the entry name will be displayed on the 1st line instead of CID name data. Both the Talk indication LED and key backlight shall be flashed during ringing. (0.25 s ON/OFF) And both key backlight and LCD backlight shall be turned on. Handset and base ringer melody and level as MENU setting. Note 2: It is possible to change ring volume during the incoming alert by using KEY_UP/CLIP and KEY_DOWN/CLIP keys. The ring volume will be displayed as “Volume n” (1<=n<=3) or “Volume OFF” during 8 s unless KEY_HOOK is pressed. Incoming alert phase: The incoming call phase begins with the first ring (ALERT_ON) signal of the handset and stops: • If the user take the call (see operation) • If the call is not answered and the caller release its call or another parallel phone answers. EXT icon and LEDs will stop flashing after FTXX_LINE_EXPIRY. The Base ring alert is synchronized with the PSTN ring ON/OFF pattern. RPAS disable: If the first ring period is less than the RPAS length value which is define by EEPROM, the unit shall not emit the ring alert sound. It is possible to be enabled by base setting menu. And the default setting shall be defined by EEPROM setting. 3.1.1 To answer the call: Press KEY_HOOK. Simply lift the handset from the cradle. HOOK_IND icon will be displayed. Note 1: After it goes to talk mode automatically, KEY_HOOK will be disabled about 3 seconds to prevent unwanted hang up. Note 2: Once handset TALK on, another handset’s display “EXT” icon and can not TALK & TONE_BUSY in earpiece if press KEY_HOOK 3.2 External outgoing call Normal dialling : • Press KEY_HOOK • Enter the called number Pre-dialling: Pre-dialling allows you to enter and modify a number before dialling. • Dial your called number. Up to 32 digits (included pause, *,#)are allowed. If the number exceeds 12 digits, then move to 2nd line. If more than 24 digits, the last 24 digits are displayed and LEFT_ARROW is ON, Press KEY_CLEAR key to delete last digit. • Press KEY_HOOK, the digits are dialled, digit(s) 15 of 40 3.2.1 Dialling PAUSE Press KEY_LNR (after first key) to make a pause, which is displayed as a "P". The time is adjustable by FP EEPROM settings 3.2.2 Flash key During a call, press shortly KEY_R to perform a Flash break and displayed as a “R”. The flash time is adjustable by FP EEPROM settings 3.2.3 DTMF dialling DTMF tone duration (pause before, tone length, pause after, high & low group level) is adjustable by FP EEPROM settings 3.2.4 Pulse dialling Pulse timing (make, break, pause after) is adjustable by FP EEPROM settings Pulse dialling mode can be disabled by EEPROM settings. (If disabled by setting, the dialling setting menu shall not be on the handset setting menu) 3.2.5 Temporary DTMF dialling During a call or pre-dialling, when the selected dial mode is pulse and you want to dial DTMF codes, During talk, press KEY_STAR/LOCK to switch into DTMF dialling, only during this call. During pre-dialling or number storage, long press KEY_STAR/LOCK is used to program the digits after the KEY_STAR going temporarily to DTMF dialling. This will be displayed “d”. 3.2.6 Dial tone detection During an external outgoing call, the dial tone detection is activated. When detected the digits which have been dialled on the handset (pre-dialled or post dialled) are sent to the line. If the dial tone is not detected, a time out expires and the digits are sent. The time out is adjustable by FP EEPROM settings No dial tone detection time out: selected by EEPROM data. With dial tone detection time out: selected by EEPROM data. 3.2.7 Call timer display After going off hook, the display is blank during 15 s unless you press a key. The communication duration is displayed after 15s after the last pressed key on the 2nd line. If you press a key (0 - 9) during the conversation, the communication duration is not reset to zero and keep count up on the 2nd line. At the end of each call, the duration of communication is displayed for 5 seconds on the 2nd line. The last 12 digits of dialled number is keeping display on the 1st line during the call. 3.2.8 Mute It is possible to mute the microphone during a conversation. Press KEY_CLEAR/KEY_MUTE during the conversation, the microphone is then deactivated, the external correspondent is put on hold; you can talk freely without being heard by the calling party. “MUTE” is displayed on the 1st line. No digit key or KEY_INT can be used during mute. Press KEY_CLEAR/KEY_MUTE again to return to normal mode. The 1st line then return to display last 12 digits of dialled number. The Phonebook can be reviewed, but it cannot be used for dialling. Press KEY_CLEAR/KEY_MUTE again to return to normal mode. 3.2.9 Changing Earpiece Volume during Call It is possible to change earpiece volume during a call using KEY_UP/CLIP and KEY_DOWN/CLIP. 16 of 40 The earpiece volume will be displayed on the 1st line as “Ear Vol n” (1<=n<=5) during 8 s unless a key digit (KEY_0 to 9 + KEY_HASH + KEY_STAR) is pressed. 3.3 Direct access memory The product has three locations of direct access memory dial number. The number can be reprogrammed by end user using handset menu (Hot keys). The maximum digits for each location are 16 digits and there is no name for this direct access dial number. The following data shall be able to store to two direct access keys. 0 - 9, * , # , R , Pause # If insert the “R”, it should have 1.5 seconds pause after the “R”. EX: If store the “1234R78” to direct access keys. The dial shall be as follow “1” + “2” + “3” + “4” + “Recall” + “1.5 second pause” + “7” + “8” 3.3.1 How to access the direct memory dial number during idle User press and hold the KEY_1 or KEY_2 for more than 1.5 second (Long press), then the unit display the pre-programmed number on the LCD. KEY_1 for location number 1 and KEY_2 for location number 2. Then take the line and start to dial automatically. 3.3.2 During OFF HOOK When the unit is on OFF HOOK mode, it is allowed to access direct access memory number anytime when long press for KEY_1 or KEY_2. 3.3.3 Direct access dial data The direct access keys dial data should not be stored to the Redial buffer. If use direct access keys after dial some digits, only the digits before direct access keys dial will be stored to the redial buffer. 3.4 3.4.1 Redial feature Limit for number of redial digits There are two EEPROM setting data to define the maximum redial digit. Those two data must be lower than 32 (20h). If more than 32, the reading data will be replaced by 32. 3.4.1.1 Selection for Redial data size • The unit shall compare the two redial size data. If the data are same, there will be no redial size selection menu. • If the data are different, there will be Redial size selection menu. Then the user can select the redial size by selecting the value. (Redial size selection menu --> see Menu setting) • On the menu, the size data shall be come from EEPROM setting data. 3.4.1.2 Relation between redial list and redial size limit • Redial list can keep up to 32 digits for each entries. • When select the dialled number from the redial list and the number of digits is higher than selected limit, the unit display only the digits up to size limit. • When press KEY_TALK to start dialling, the unit dial out only up to limit. The rest of digit will not be dial out. 3.4.2 Redial list 17 of 40 Up to 20 last redial numbers (32 digits) are stored in the redial list (in PP EEPROM). Outgoing calls to SMS service centre will not be stored in the call list. The last calls appear with their name if they are stored in the phonebook. To retrieve the entries: Press KEY_LNR If the list is already empty, then “empty” is displayed on the 1st line. • When view the redial list, the 1st line to display most update data and 2nd line to display next list. • Press KEY_DOWN/CLIP to move the 2nd line data to 1st line and 2nd line to display next data. Press KEY_UP to move the 1st line data to 2nd line and 1st line to display most old redial data. • There is arrow icon on the left side of the 1st line to indicate that • Scroll through the calls with the up KEY_UP/CLIP and down KEY_DOWN/CLIP arrows. The phonebook name is displayed if it exists. Otherwise it displays the first 11 digits of the number. If the digits are more 11, the first 11 digits of number are displayed with icon. Press KEY_OK to check the remaining digits with • • icon. Press KEY_OK to toggle between name and number if the number is matched with phonebook entry. (This is only for 1st line data) Press KEY_MEM/EXIT return to standby mode To dial out number just simple press KEY_HOOK. [Display example] (Arrow icon is always on the 1st line left side) 3.4.3 Dial out redial after OFF HOOK To recall the last redial entry, just take the line by KEY_HOOK and press KEY_LNR to dial. 3.4.4 Delete a redial buffer : • • Press KEY_CLEAR and “Delete ?” appears. Press KEY_OK to make redial number deleted for 1st line data, or press KEY_MEM/EXIT to cancel the delete operation. To return to the previous menu, press KEY_MEM/EXIT 3.4.5 Delete all redial buffer : • • Long press KEY_CLEAR and “Delete All ?” appears. You can either press KEY_OK again and all redial are deleted, or press KEY_MEM/EXIT to cancel the delete all operation. To return to the previous menu, press KEY_MEM/EXIT 18 of 40 3.4.6 Store a Redial list into PHONEBOOK • • • • • • • Press KEY_OK during display the redial number which you wish to store to the phonebook. The display show “Add ?”. After appearing the “Add ?” And press KEY_OK to confirm. The display show “Name ?”. Enter the name. Press KEY_OK after enter the name. Press KEY_OK after modify the number. Select the melody of your choice (1 to 5) and validate Press KEY_OK to confirm. Remark: • • 3.5 If the total digit of Re-dial data inside the re-dial buffer is more than Re-dial size limit, it will only be able to transfer the digits up to Re-dial size limit. If the re-dial data size is more than Phonebook size limit, it will only be able to transfer the digits up to Phonebook limit. Internal call transfer When you wish to transfer an external call to another extension: • • During a call, press KEY_INT Select the number of the internal correspondent that you wish to call; the external caller is put on hold. • When the internal correspondent picks up, press KEY_HOOK to hang up and transfer the call. If the internal correspondent does not pick-up, press KEY_INT again to reconnect to the external caller on line. 3.6 Conference call between two handset and external caller When you wish to talk an external call and other handset: • During a call, press KEY_INT • Select the number of the internal correspondent that you wish to call; the external caller is put on hold. • When the internal correspondent picks up, you can talk with internal correspondent first with external call on hold. • Press KEY_# to go to Conference call. • When one of handset press KEY_HOOK or press KEY_INT. Then the conference call is finished, but other handset still talk with external caller. If the internal correspondent does not pick-up, press KEY_INT again to reconnect to the external caller on line. 3.7 Caller ID (CLIP) features 3.7.1 General features The phone supports CLIP DTMF and FSK type I and II. See 10.1 for more details. 3.7.2 Caller ID display Note: Caller identification is only available if you have subscribed to this service with your network operator. During the incoming alert: The CLIP information is displayed if they are provided. Order of display: 19 of 40 • • • • Phonebook name is on the 1st line and calling number is on the 2nd line if the number matches with the CLIP calling number CLIP calling name is on the 1st line and calling number is on the 2nd line if the name data is transmitted. However, if the number is match with one of phonebook memorized number, it shall use phonebook memorized name. CLIP calling number Number matching method is as follows. - If the one of number which CLIP or phonebook is less than 5 digits, it will not compare. (If the one of phonebook number is 1234, this number will not use for number matching) - If the CLID received 10 digits and phonebook number is 8 digits, CLID last 8 digits will use for the matching with that phonebook number. And if the CLID is 8 digits and phonebook number is 10 digits, Phonebook number last 8 digits will use for the matching with that CLID number. The following special network messages are managed and displayed at the place of calling number: Message WITHHELD UNAVAILABLE CLIP type FSK type I & II FSK type I & II Meanings The caller hides its identity Network failure, the calling number can’t be transmitted Special caller texts display format: (Display on the 1st line) Display CLIP TYPE Caller texts from network Private FSK type I & II PRIVATE Unavailable FSK type I & II UNAVAILABLE International FSK type I & II INTERNATIONAL Operator FSK type I & II OPERATOR Payphone FSK type I & II PAYPHONE Ringback FSK type I & II RINGBACK Withheld FSK type I & II WITHHELD Note: If text data area has above information, the display shall be according to the text data, than “Parameter name” The following parameter shall be detected: Parameter type 01h 02h 04h 04h 06h 07H 0Bh 0Bh 11h 16h Parameter 4Fh 50h 4Ch 00h FFh 02h 0Fh Parameter name Date and Time Calling Line Identify UNAVAILABLE WITHHELD INTERNATIONAL Calling Party Name Deactivation VMWI Activation VMWI RINGBACK PAYPHONE Display Date and Time Number Unavailable Withheld International Calling Party Name Ringback Payphone Note: If Date and Time data is not available, it shall store and display the date and time data from handset inside timer. The “Withheld” display can be changed to “Private” by EEPROM setting. The icon will stay during all incoming alert phase and during call if you answer the call. 20 of 40 The call timer display will come again after 15 seconds if no key pressed. During standby mode: The icon will flash if un-viewed unanswered CLIP(s) in call list, unanswered call is read. icon will be off after all 3.7.3 VMWI indication Refer to the VMWI operation 3.7.4 Recall CLIP list Unanswered and answered calls are stored in the CLIP list of each handset independently (in EEPROM). Note: any new CLIP call will be stored in EEPROM . Size storage Each entry will store: ¾ ¾ ¾ The call number (20 digits) The caller name (12 digits) if the network send it The date and hour of the call Storage sequence The CLIP information that has been received during incoming alert phase (calling number, name date/hour) is stored then displayed. If the new call entries, The icon will flash (480ms ON/OFF) and will off after all new call is read. Note: The new message indication is reset at power up, so the icon is always off after a reset. MMI operation To retrieve the entries: 1. Press KEY_ UP/CLIP or KEY_ DOWN/CLIP to enter the call list. The icon will stay ON icon will stay ON for Answered Calls. If the list is already for Unanswered Calls and the empty, then “EMPTY” is displayed on the 1st line 2. [Display example] 3. 4. Scroll through the calls using the up KEY_UP/CLIP and down KEY_DOWN/CLIP arrows. You will find the different fields of the entry: 21 of 40 If the call is unanswered and un-viewed. The and icon will stay ON. The will be turned off after it is viewed. If a matched number found in phonebook memory , the corresponding name will be shown otherwise if the caller name is available, the caller name will be displayed. If both are not available, the caller number is displayed on the 1st line. Press KEY_OK, the first 12 digits of caller number is displayed on the 1st line. If the number is more than 12 digits, the first 12 digits are displayed with icon. Press KEY_OK to check the remaining digits with 5. icon. When the CLIP found no matched number in Phone Book and Calling Number is present, when press KEY_OK again , CLIP data can be stored into phone book ( see 3.7.7) To select another call list, simply press KEY_UP/CLIP or KEY_DOWN/CLIP . Error tone will be sounded if reach the top or bottom of the list. To return to the previous menu, press KEY_MEM/EXIT. To dial out number just simple press KEY_HOOK 3.7.5 Delete one CLIP list • • 3.7.6 Press KEY_CLEAR and “Delete ?” appears. There you can either press KEY_OK and CLIP deleted, or presses KEY_MEM/EXIT to cancel the delete operation. Delete all CLIP list • • Long press KEY_CLEAR and “Delete All ?” appears. There you can either press KEY_OK and all CLID are deleted, or press KEY_MEM/EXIT to cancel the delete all operation. To return to the previous menu, press KEY_MEM/EXIT 3.7.7 Store a CLIP list into PHONEBOOK • • • • • • After appearing the “Add ?” and press KEY_OK to confirm ( after 3.7.4 step 5 ) Press KEY_UP/CLIP or KEY_DOWN/CLIP to move the cursor for edit or delete name. If the CLIP data does not have name, LCD shall display “Name ?”. And then enter the name. Press KEY_OK after modified or enter the name. Press KEY_OK after modified number. Select the melody of your choice (1 to 5) and validate Press KEY_OK to confirm. 3.7.8 Dial out CLIP list To recall the number from CLIP list, pressing KEY_HOOK will dial out the number. 3.7.9 3.7.9.1 KPN specification handling DC/AC load activation • When the unit detect the line reverse, the DC/AC load shall apply within 100mS 200ms. • When the unit detect line reverse, the unit need to wait next line reverse. If next line reverse detect within 80ms, it define that the line reverse is due to ringer signal. • If the line reverse is due to ringer signal, the DC/AC load shall not apply • During ringing stage, if detect ringer off for more than 80ms. The unit shall be ready for detecting line reverse. 22 of 40 • To detect line reverse, the unit shall detect PSTN line 1 and line 2 both polarity changing within 10mS. If only one line polarity changing, it should not be polarity changing. It should be line voltage interruption. After finish the call and go to idle stage, the unit shall not detect line reverse for about 100mS from line releasing point. DC load shall be 90Kohm - 110Kohm. AC load impedance in the voice band shall be greater than 1800ohm and preferable lower than 2400ohm. • • • 3.7.9.2 DC/AC load release • After detect the line reversal, if the unit does not detect the CID DTMF signal within 1S. • During receiving the DTMF, if detect the DTMF pause for more than 1 S. • When received the DTMF ‘C” (Stop code). • Ringer signal is received. • OFF HOOK the telephone 3.7.9.3 DTMF signal detection • A valid DTMF signal > 40mS shall be interpreted as a valid digit. • A valid DTMF signal < 40mS shall not be interpreted as a valid digit. • If not valid DTMF signal is present during > 40mS, this shall be interpreted as an inter digit pause. • If not valid DTMF signal is present during < 40mS, this shall not be interpreted as an inter digit pause. • A level > 37mV shall be recognized as a valid digit. • A level < 28mV shall not be recognized as a valid digit. 3.8 Phonebook The phonebook contains up to 50 names of 12 characters max. and numbers of 24 digits. Phonebook is stored in PP EEPROM. One handset phonebook is independent from other locked handsets. 3.8.1 Dial a number of the phonebook list To call a correspondent whose name you have saved in the phonebook: • Press KEY_MEM/EXIT to enter the phonebook. The will be ON. [Display example] • Press the first letter of the name; the first name that starts with this letter in the alphabet appears. For instance to find names beginning by A, press once on KEY_2, to find names beginning by B, press twice on KEY_2, to find names beginning by C, press three times on KEY_2 23 of 40 • • • • 3.8.2 See the dial number of the phonebook list during Talk. • • • • • 3.9 Go through the list of names with the KEY_UP/CLIP and KEY_DOWN/CLIP keys the list scrolls up/down in an alphabetical order. If press KEY_DOWN/CLIP, the 2nd line entry move to 1st line and next entry is displayed on 2nd line. Press KEY_MENU/OK to display the number and user can press the KEY_MENU/OK again to display remaining digits if the recalled phone book number is more than 12. This is only for 1st line displayed entry. Press KEY_MEM/EXIT returns to standby mode OR Press KEY_HOOK to dial the number of the correspondent whose name is displayed on the 1st line. Press KEY_MEM/EXIT to enter the phonebook. The will be ON. Press the first letter of the name; the first name that starts with this letter in the alphabet appears. For instance to find names beginning by A, press once on KEY_2, to find names beginning by B, press twice on KEY_2, to find names beginning by C, press three times on KEY_2 Go through the list of names with the KEY_UP/CLIP and KEY_DOWN/CLIP keys the list scrolls up/down in an alphabetical order. Press KEY_MENU/OK to display the number and user can press the KEY_MENU/OK to start dialling or display remaining digits if the recalled phone book number is more than 12. Press KEY_MEM/EXIT to returns to normal Talk mode Intercom 3.9.1 • • Internal call Press KEY_INT Enter the number of the internal handset (1 or 2) and “INT” icons displayed, the number of the internal handset display “INT” with caller The handset number and rings (INT Melody). Remark: the caller handset go to standby mode if the number of the internal handset is not available or caller handset. Before enter the number of internal handset, incoming call applied then go to ring in mode. 3.9.2 End of intercom call Incoming call applied then go to ring in mode. The number of the internal handset press KEY_HOOK go to INTERCOM mode 3.9.3 Intercom mode The 3.9.4 and “INT” icons displayed on both handsets. End of intercom Any handset (intercom) press KEY_HOOK, go to standby mode. Incoming call applied then go to ring in mode. 3.10 Page button 24 of 40 Press Page button on the base. The handsets will ring RING_1 at volume of handset internal ring level setting and display INT with “□□□□”during 30s unless page key is pressed again on the base or a key is pressed on any locked handset. (When the handset set to key lock, but it shall be possible to stop the handset paging sound by pressing any key) 3.11 Battery and charge management 3.11.1 Battery indicator 5 levels indicators icon for mean battery voltage: > = EEP_BAT_FULL_LEVEL > = EEP_BAT_HALF3_LEVEL > = EEP_BAT_HALF2_LEVEL, Blanking > = EEP_BAT_ALARM_LEVEL 3.11.2 Low battery conditions If the following conditions are applied: During a call, • If mean battery level is less than EEP_BAT_HALF1_LEVEL, • If battery warning tone option is ON then a TONE_LOW_BATT will be emitted every minute. In any state (standby or call), If mean battery level is less than EEP_BAT_ALARM_LEVEL, handset will enter in power down mode. 3.11.3 Charge conditions If the following conditions are applied: • In standby mode, • If battery warning tone option is ON • The handset is put on its charger (debounce time: 200 ms) then a TONE_CONFIRM will be played. Charging icon: Scroll for display handset is charging, fast scroll when quick charging mode, 3.11.4 Start-up with low batteries If battery level at start-up is lower than EEP_BAT_HALF2_LEVEL, the handset will stay in sleep mode (no LCD, no RF, no MMI working). You need to put the handset into charge until battery level reaches EEP_HALF2_LEVEL. 25 of 40 3.12 Range indication 3.12.1 Out of range tone If the following conditions are applied: • The handset has been out of range since EEP_RANGE_OUT_DELAY s • If range warning tone option is ON then a TONE_WARNING will be played. EEP_RANGE_OUT_DELAY : selected by EEPROM data 3.12.2 In range tone If a TONE_WARNING has been played, a TONE_IN_RANGE is played when the handset goes into range the next time. Note: at start-up, the handset plays the TONE_IN_RANGE only if it goes into range after more than 10 s. 3.12.3 Range limit tone during a call During a call, in range limit conditions, the handset will play a TONE_WARNING in the Buzzer The tone is repeated until range conditions are good If the handset goes out of range, the call is released (on both handset and base). 3.13 Clock and Alarm clock 3.13.1 Clock The handset has clock indication. The clock data is inside the base unit. So, all the handsets have same clock indication. • Update the time by using one of handset. • The time data is also updated by CLIP data if the CLIP data has time data. 3.14 Alarm activation When the unit is set to alarm ON and the clock reach to the alarm setting time, the handset shall generate the alarm sound. And Alarm icon needs to be turned ON on the LCD. Once the clock is reach to alarm setting time, start to generate the alarm sound. When stop generating alarm sound, the alarm setting shall be OFF and the icon shall be turned OFF. 3.14.1 During idle The sound level shall follow the handset internal ring level. However, if the setting is “OFF” the alarm sound level shall be “Level 1”. During generating the alarm sound, press any key to stop the alarm without any operation even the handset is “Key Lock” mode. For example, press “KEY_HOOK” to stop the alarm, however, the handset should not go to talk mode. If do not press any key for more than one minute, the alarm shall stop automatically. 3.14.2 During Talk 26 of 40 The sound level shall be same as Battery Low warning tone. During generating the alarm sound, press any key to stop the alarm without any operation. 3.14.3 During ringing or paging The alarm sound shall not active during paging or ringing. 27 of 40 4 MENU Settings Menu structure A wide range of phone settings are accessible through a user friendly menu. • To enter the menu, press KEY_MENU/OK • Scroll through the selections using the KEY_UP/CLIP and KEY_DOWN/CLIP keys, the selections scroll in a loop (you return to the first after the last). To validate a selection, press KEY_MENU/OK • To return to the previous menu, press KEY_CLEAR. • To escape a menu and return to standby mode, press and hold KEY_CLEAR. • After 15 s without pressing any key, the handset returns in standby mode Phonebook SMS (Refer to SMS operation document) MSG Play **** TAM Setting **** Setup Add Entry Modify Entry Delete Entry Number ? Melody 1 … 5 (Refer to SMS operation document) (Refer to DECT 15 operation document) (Refer to DECT 15 operation document) Base Volume Base Melody Del Handset PIN Code Dial Mode Volume off Volume 1 ... 5 Melody 1 … 5 PIN ? PIN ? Default Tone Dial Pulse Dial Recall 1 Recall 2 ON OFF PIN ? Beep Key Tone Recall First Ring Handset Name ? Melody 1 … 5 Confirm ? Low Battery Out of Range INT Ring Vol INT Melody EXT Melody Volume OFF Volume 1 … 5 Volume OFF Volume 1 … 5 Melody 1 … 10 Melody 1 … 10 Date and Time Date ? EXT Ring Vol Handset ? New PIN Re-Type Confirm ? ON OFF ON OFF ON OFF DD / MM 28 of 40 Alarm Set Auto Answer Name Redial Size *** Time ? HH : MM ON OFF OFF ON Time ? XX (EEPROM setting 1) YY (EEPROM setting 2) **Language English French German Italian Spanish Nederland Scandinavian Hot keys Hot key 1 Hot key 2 XXXXXXXX YYYYYYYY *+ Base 1 2 3 4 Auto + Base 1 2 3 4 New Base X (Display current setting number) Key Lock ? Register Select Base Reg Base Searching... PIN ? Notes : * Only registered base number will be shown. Notes : + Registered Base Number will blinking Notes : ** The languages are just example. (Defined by other section) Notes : *** This menu only appear when the value of EEPROM setting 1 and EEPROM setting 2 are different. Notes : **** Those menu for DECT 15. DECT 10 handset shall have ability to be registered to DECT 15 Base. Once register to DECT 15 Base, those menu appear on the menu screen and function as DECT 15 handset. Refer the DECT 15 MMI document PHONEBOOK 4.1 • 4.1.1 • • • Select "PHONEBOOK" Add a name Select "Add Entry" Enter the new name and validate. Enter the new telephone number and validate 29 of 40 • • • It is possible to enter the following data for number entering. - KET_1 to KEY_0 - KEY_STAR and KEY_# - KEY_LNR (Pause) - KEY_R (Recall, Flash) Select the melody of your choice (1 to 3) and validate Press KEY_OK to confirm. With your telephone you can write text as well as figures. This is useful for entering a name into the address book, giving a name to a handset, … To select a letter, press the corresponding key as many times as is necessary. For example to select an 1, press 2 once, to select a B, press 2 twice and so on. To select A and then B consecutively, select a 1, wait until the cursor moves on to the next character, then select a B. Select Upper case (Space) Ä É Γ Λ Ñ Ü Å ∆ Æ Φ Ö Π Θ Ξ Ø Ψ Ω Σ ä è ì à é å æ ñ ù ò β ü ö ø ç Change the case Lower case (Space) Change the case The following symbols need to be under “0” and “*” ¥ ¡ £ ¿ € § ¤ 30 of 40 4.1.2 • • • • 4.1.3 • • • • • • • • • 4.1.4 Delete a name Select "Delete Entry" and then press KEY_OK Move through the list of names using the KEY_UP/CLIP and KEY_DOWN/CLIP keys the list scrolls down in alphabetical order. Press KEY_OK when you find the name you wish to delete "Confirm ?" appears, press KEY_OK to confirm. Modify a name or number Select "Modify Entry" and then press KEY_OK Move through the list of names with the KEY_UP/CLIP and KEY_DOWN/CLIP keys. The list scrolls down in alphabetical order. Press KEY_OK when you find the name to modify Press KEY_UP/CLIP or KEY_DOWN/CLIP to move the cursor for edit or delete name. Press KEY_OK after modified name. Press KEY_CLEAR to delete number. Press KEY_OK after modified number. Select the melody of your choice (1 to 3) and validate Press KEY_OK to confirm. Change the character case During entering the name or modifying the name, the user can change the character case by pressing KEY_#. When enter the name editing menu, the starting character is always upper case. The character case indication shall be on the Time display as follows. • Upper case • Lower case 4.2 SETUP • Select "Setup" 4.2.1 BASE VOL This menu enables you to adjust base ring volume • Select "Base Volume" and validate • Select the desired volume (Volume OFF or Volume 1 to 5) and validate 4.2.2 BASE MEL This menu enables you to select base ring melody • Select "Base Melody" and validate • Select the melody of your choice (1 to 5) and validate 4.2.3 DEL HS You can cancel a handset’s association with a base to allow another handset to be associated • Select "DEL Handset" and validate • Enter the PIN code and validate • Select the handset to be cancelled and validate 31 of 40 4.2.4 PIN CODE The base PIN code is used in subscription operation or to modify some critical parameters in the base. To change the PIN code: • Select "PIN code" and validate • Enter the old 4 figure confidential code and validate • Enter the new 4 figure confidential code and validate • Enter the new confidential code a second time and validate 4.2.5 Dial mode selection (This mode will not appear when set the Pulse dialling disable by EEPROM) Two types of dialling are available: 1. 2. DTMF tone dialling Pulse dialling To change the dialling mode: • Select “Dial Mode” and validate • Select “Tone” or “Pulse” of dial mode and validate FTXX_DIAL_MODI : selected by EEPROM data Note: the Dial mode selection menu can be hidden to lock the base into pulse or DTMF dialling by the CONFIG_ENA_MENU_DIALMODE flag (see various factory settings). 4.2.6 Recall duration selection • Select "Recall" • Choose Recall 1 to select short flash time • Choose Recall 2 to select long flash time RECALL 1 & 2 timing: selected by EEPROM data Note: not recall select function in if Recall 1 & Recall 2 is same timing. 4.2.7 Default settings This menu enables you to reset both handset and base with default settings. • Select "Default" • Enter the base PIN code and validate • "Confirm ?" appears, press KEY_OK to confirm Then the handset and base will apply default parameter settings and make a software RESET. Default parameter Handset name Low battery indicator Out of range indicator Key click Auto answer INT melody INT volume EXT melody EXT volume Ear volume Language Phonebook CLID list Redial list PIN CODE PAUSE Dial mode Value To be advised ON ON ON ON English Empty Empty Empty 0000 3s DTMF 32 of 40 Key lock Clock Alarm Date RPAS enable /disable Handfree mode speaker volume RPAS length setting Recall setting Redial size Handset Name Hot key 1 number Hot key 2 number OFF 00:00 OFF Jan 1st Enable 3 (Only for DECT 24) 400mA Recall 1 32 Handset XXXXXXXXXX (TBA) XXXXXXXXXX (TBA Default values in handset and base are defined by EEPROM settings [1]. So they can be adjusted for each country. 4.3 HANDSET • Select "Handset" 4.3.1 BEEP Beep features The handsets may or may not emit beeps while the keys are pressed , the batteries are low and when the handset is out of range of the base. 4.3.1.1 • • 4.3.1.2 • • 4.3.1.3 • • KEYTONE Select "Key Tone" and validate Select “ON” or “OFF” and validate LOW BATTERY Select "Low Battery" and validate Select “ON” or “OFF” and validate OUTRANGE Select "Out Range" and validate Select “ON” or “OFF” and validate 4.3.2 INT RING VOL This menu enables you to adjust handset ring volume (intern melody) • Select "INT Ring Vol" and validate • Select the desired volume (Volume OFF or Volume 1 to 5) and validate 4.3.3 EXT RING VOL This menu enables you to adjust handset ring volume (extern melody) • Select "EXT Ring Vol" and validate • Select the desired volume (Volume OFF or Volume 1 to 5) and validate 4.3.4 INT MELODY This menu enables you to choose a different melody for internal call • Select "INT Melody" and validate • Select the melody of your choice (1 to 5) and validate 33 of 40 4.3.5 EXT MELODY This menu enables you to choose a different melody for external call • Select "EXT Melody" and validate • Select the melody of your choice (1 to 5) and validate 4.3.6 DATE AND TIME There are two menu inside the DATE and TIM. One is to set the date and other is to set the time. 4.3.6.1 Date setting • Select the DATE ? • When enter Date setting mode, LCD display current Date with flashing Date indication. (Display on dots matrix area) • Enter the Date and Month by the following format. - The format is DD / MM. If the Date is 5th, it should enter “05”. If the date is 15th, it should enter “15” - After enter data, enter the month. If Jan, it should enter 01. • If the CLIP data has Date data, the Date data shall be updated by CLIP Date data. • The Date data shall be kept at base unit and when the handset turned on, the Date data shall be transferred from base to handset. • If enter wrong data such as 32nd for Date field, it will be error tone and change to 01 on date filed. 4.3.6.2 Time setting • Time setting should be 24 hour format. • When enter Time setting mode, LCD display current time with flashing hour indication. (Display on dots matrix area) • Enter the current time by 24-hour format and validate. And same time, the update data send to base to keep for all the handset to have same clock. • After validate the time, the time indication move to 7-segment time display area. • If the CLIP data has time data, the clock shall be updated by CLIP time data. • The time data shall be kept at base unit and when the handset turned on, the time data shall be transferred from base to handset. • If enter wrong data such as 25 for Hour field, it will be error tone and change to 01 on hour filed. 4.3.7 ALARM SET This menu enables you to set the Alarm. • Select “Alarm Set” and validate. • Select “ON” or “OFF” by using KEY_UP/DOWN key and validate. • If select “ON”, the display shows previous setting time with flashing hour indication. (If no previous data, the display should be 00:00) • Time setting is same as Clock setting. • After set the Alarm time, the Alarm icon shall be ON. 4.3.8 AUTO ANSWER When there is an incoming call and the handset is on the base, the phone automatically takes the line. • Select "Auto Answer” and validate • Select "ON" to activate "OFF" to deactivate and validate 4.3.9 NAME This function allows you to personalise each handset. • Select "Name" and validate • Enter the name and validate (max 10 chars) • During entering the name, the user can select the character case by pressing KEY_LNR 34 of 40 4.3.10 KEY LOCK This function allows you to lock the key • Select "Key lock ?” and validate • Press KEY_MENU/OK to lock key, icon displayed and go to standby mode. Note: Press KEY_HOOK key can be OFF HOOK during incoming call and Key Lock is on. 4.3.10.1 Quick KEY LOCK Simply press and hold KEY_STAR/LOCK 3 second 4.3.10.2 To unlock key: • • 4.4 Press any key “Press ＊” is displayed, within 5s time out Press KEY_STAR/LOCK to unlock key REGISTER • • • 4.4.1 • • • • • 4.4.2 • • • • • • • Select "Register" and validate Select “Select Base” or “Reg Base” by KEY_UP or KEY_DOWN Press KEY_OK to confirm SELECT BASE Select "Select Base" and validate “Base 1 2 3 4” is displayed (only the registered base number will be shown and current base number will be blinking) Press 1 - 4 to confirm the selection or KEY_UP/KEY_DOWN + KEY_F to select auto searching. Valid tone is sounded if valid base is found “Not Register” is shown and error tone sounded the selection is invalid REG BASE Select "Reg Base" and validate “Base 1 2 3 4” is displayed (only the registered base number will be blinking ) Press 1 - 4 to confirm the selection It is now searching the base in subscription mode and “Searching…” is displayed Valid tone is sounded and “PIN ?” is shown if valid base found Enter subscription PIN code and verified by base Valid tone sounded if subscription is successful and back to standby mode. On the base: • • Put the base into subscription mode, by pressing and holding PAGE_KEY The base will then emit a beep, the Line LED will flash. It is now ready to be associated with a new handset, during the 90 seconds after pressing the button only. If the handset has located the base, a valid tone is played. If the handset does not locate the base, it will return to the previous configuration after 1 minute. Try again by changing the base number and check that you are not in a environment where there is interference When a handset is associated with a base, it is given a handset number by the base. It is this number which is displayed on the handset after the name and must be used for internal calls. 35 of 40 5 Prefix dialling There are two data for prefix dialling. One is Detect string and other is Replace string. If user enter the number and first several string match with the pre-programmed string data, then the string will be replaced by pre-programmed Replace string data. This function can be enabled or disabled by EEPROM setting. When this function is active, the maximum number of digits for pre-dial is 31 digits. 5.1 Detect string The pre-programmed detect string is 5 digits inside the EEPROM. The data is 1 to 0 and F (F is for blank) If the Detect string need to be 003 then the data shall be F,F,0,0,3 5.2 Replace string The pre-programmed replace string is maximum 10 digits inside the EEPROM. The data is 1 to 0 5.3 Detecting and replacement The prefix dialling is only working when the dialling is prepared dialling which mean enter the dial number during idle mode and then OFF HOOK. The product will check the first few digits (maximum 5 digits depended on Detect string data) and if match with detect string, then replace the detected string to the replace string. If the detect string is all F, there will be no matching and add the replace string to the dialled number except the dialled number starting from not 1 to 0. EX 1 Detect string : FFF00 Replace string : 1234567 Dialling number : 00567456 The product will dial ---- 1234567-567456 EX 2 Detect string : FFFFF Replace string : 1234567 Dialling number : 00567456 The product will dial ---- 1234567-00567456 EX 3 Detect string : FFFFF Replace string : 1234567 Dialling number : 13567456 The product will dial ---- 1234567-13567456 EX 4 Detect string : FFFFF Replace string : 1234567 Dialling number : #13567456 The product will dial ---- #13567456 EX 5 Detect string : FFFF0 Replace string : 1234567 Dialling number : 00567456 The product will dial ---- 1234567-0567456 EX 6 Detect string : FFFF0 Replace string : 1234567 Dialling number : 0567456 36 of 40 The product will dial ---- 1234567-567456 EX 7 Detect string : FFF00 Replace string : 1234567 Dialling number : 0567456 The product will dial ---- 0567456 6.1 DECT 24 addendum (Set the EEPROM setting for DECT 24) Change to Handset keypad layout All keys have the same function as those in the DECT 10 specification KEY_CLEAR KEY_HANDSFREE KEY_CASE KEY_OK KEY_MENU KEY_UP KEY_LNR KEY_PAUSE KEY_MEM KEY_ESC KEY_DOWN KEY_CLIP KEY_HOOK_OFF KEY_HOOK_ON KEY_1 KEY_2 KEY_3 KEY_4 KEY_5 KEY_6 KEY_7 KEY_8 KEY_9 KEY_STAR KEY_DTMF KEY_0 KEY_R POWER DOWN KEY_HASH KEY_INT 37 of 40 6.1.1 LCD display The LCD display is composed of 12 characters dots matrix form (8 X 5 matrix), 4 characters 7 segments and 18 icons. (Icon drawings are just reference only. Plesae refere to the LCD specification) The definition of the icons is as follows: (Icons are just reference only) Icon NAME Definition HOOK_IND Off hook indicator EXT EXT External call engaged INT INT Internal call engaged NEW_CLIP_IND Caller identification available /new numbers in call listing CLIP_ANSWERED Indicate answered call CLIP_UNANSWER Indicate unanswered call ED PHONEBOOK_IND Phonebook indicator MENU_IND Menu indicator BATTERY 3 levels battery indicator 1 segment: weak, 2 segments: medium, 3 segments: full The segments scroll during battery recharging and stop scrolling when battery is full Handset keypad locked LOCK_IND TAM_MSG Signal strength indicator. The icon is steady when handset is locked to its base The icon flashes when the handset is unlocked or not subscribed to any base Indicates that displayed number or message is longer than the screen (12 digits) Indicates that displayed number or message is longer than the screen (12 digits) VMWI indication NEW_SMS_IND New SMS message indication VMWI_IND For the DECT 15 HAND_FREE Hand free indicator ALARM_SET Alarm set indicator ANTENNA LEFT_ARROW RIGHT_ARROW 38 of 40 Pressing the KEY_HANDSFREE from standby mode causes the unit to enter speakerphone mode. The call is ended by pressing KEY_HOOK_OFF. The user can switch between handsfree and normal mode by pressing KEY_HANDSFREE. Pressing UP/Down key to adjust the speaker volume during handfree mode. (5 steps) The adjusted level shall be kept for next handfree mode. The setting is only for handfree speaker volume and it shall not effect the earpiece sound level. When in speakerphone mode the SPEAKER_IND icon shows in the LCD Quick default settings If you have lost your PIN code, the following procedure allows you to restore default settings on handset and base. Press KEY_STAR on handset when power up (insert and remove batteries). The display shows “DEFAULT”. Press KEY_OK. When the handset locks onto its base, both will restart. Subscribe a new handset Refer to MENU mode’s REGISTER page The base can support a maximum of 2 handsets. If you already have 2 handsets, and you wish to change one of them, you must firstly delete a handset, then associate the new handset. 9.1 Test modes Handset test modes Refer to document of TEST MODE 9.2 Base unit test modes Refer to document of TEST MODE 39 of 40 10 Specifications 10.1 CLIP Standards The phone supports the following CLIP features defined by the identified standard: Feature FSK type I Country All applicable FSK type II DTMF Bellcore standard Standard EN 300 659-1, EN 300 778-1 and EN 300 659-3 EN 300 659-2, EN 300 778-2 and EN 300 659-3 EN 300 659-1 Annex B, and EN 300 788-1 Annex A To be advised Note : No impedance matching is required except KPN 10.2 DECT Specifications The phone complies with the following standards Part DECT Radio DECT GAP Analogue Telephone Network EMC Safety Standard EN301 406 TBR 22 TBR 21 and TBR 38 EN301 489-1 and EN301 489-6 EN 60950 40 of 40
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print Modify Date : 2006:08:21 13:37:24+08:00 Create Date : 2006:06:02 18:41:18+08:00 Comments : Press KEY_HOOK. .Press KEY_HOOK.Press KEY_INT.Press KEY_OK. KEY LOCK. Keywords : key, press, handset, select, if Company : SunCorp Tag Ad Hoc Review Cycle ID : -1778351993 Tag Email Subject : MMI of S-Impact for USA Tag Author Email : m.yamada@suncorptech.com.cn Tag Author Email Display Name : R&D - M Yamada Tag Previous Ad Hoc Review Cycle ID: 1473389178 Source Modified : D:20060509085640 Page Count : 43 Has XFA : No About : uuid:0b52c993-33ca-431d-852c-c8f73e15f8be Producer : Acrobat Distiller 6.0 (Windows) Creation Date : 2006:06:02 18:41:18+08:00 Mod Date : 2006:08:21 13:37:24+08:00 Author : Wing Headline : Creator Tool : Acrobat PDFMaker 6.0 Word 版 Metadata Date : 2006:08:21 13:37:24+08:00 Document ID : uuid:ebbd4467-a7bc-4748-87d2-de00c735e84d Version ID : 4 Format : application/pdf Title : SunCorp Generic GAP Specification Creator : Wing Subject : key press handset select if Tagged PDF : NoEXIF Metadata provided by EXIF.tools