Sunbeam I85R Transmitter Unit of the Remote Bedding Control User Manual
Sunbeam Products, Inc. Transmitter Unit of the Remote Bedding Control
Sunbeam >
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 337606 |
| Application ID | VqRKsZn/zZiL/zwEONjSmg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 36.51kB (456363 bits) |
| Date Submitted | 2003-07-05 00:00:00 |
| Date Available | 2003-07-05 00:00:00 |
| Creation Date | 2003-05-15 11:17:26 |
| Producing Software | Acrobat Distiller 4.0 for Macintosh |
| Document Lastmod | 2003-06-11 11:49:25 |
| Document Title | User Manual |
User Manual WARMING PRODUCTS IMPORTANT INSTRUCTIONSDO NOT DESTROY Warnings and Safeguards As with all electrical products, misuse of product or failure to properly follow the instructions may cause overheating, fire, or personal injury. Please read the product label and all of the instructions before using your warming product. 1 Do not use this warming product with an infant, a child, an incapacitated person, a paraplegic, a quadriplegic, a diabetic, one insensitive to heat such as a person with poor blood circulation, or anyone who cannot clearly understand the instructions and/or operate the controls. 2 Do not use with damaged cords. Damaged cords can lead to fire. Do not trap, fold, cross, or pinch cords between bed slats, mattress, or springs, or against walls, footboards, or bed frame. 3 Do not dry clean this warming product. Cleaning liquid may damage the insulation of the heating element. Improper laundering may cause problems with the heating wire which can lead to fire. 4 Do not pinch, flex, or expose the heating wire to rubbing. A damaged heating wire may result in possible overheating or fire. 5 Turn off the control for the warming product when not using. 6 Keep control away from an open window. 7 Do not use pins; they may damage the electric wiring. 8 Be sure this blanket/mattress pad/throw is used only on an AC supply current circuit of 110-120 volts. Do not use with an extension cord. 9 Excissive heating may result from folding blanket, when in actual use. 10 Keep all dogs, cats, and other pets away from this warming product. This is an electrical appliance that they can damage or be injured by. 11 Do not use blanket/mattress pad on a waterbed, sofa, bunk bed, or mechanically adjustable bed and do not use throw on a waterbed, bunkbed, or mechanically adjustable bed. 12 Do not use another electronic heating device in conjunction with your warming product. 13 Use the proper size blanket/mattress pad for your bed. For example, use a Twin Size warming blanket on a Twin Size bed. 14 If the following Important Instructions are not followed the warming product will not operate properly. 15 If you see the warming product operating improperly, unplug it immediately and call Sunbeam Consumer Service at the 800 number listed under “How to Obtain Warranty Service”. Welcome Thank you for choosing a Sunbeam® warming product. With your purchase you’ve made a real investment in your comfort and can look forward to staying warm and cozy for many cool days to come. With over 50 years of experience and over 25 million households using a Sunbeam® warming product, you can rest comfortably knowing that Sunbeam® is the brand to trust…for quality and performance. Table of contents DD Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Warming Blanket . . . . . . . . . . . . . . . . . . . . . . . 2 Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . . 3 DD Convertible Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Warming Blanket . . . . . . . . . . . . . . . . . . . . . . . 4 Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . . 5 DD 2 Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Warming Blanket . . . . . . . . . . . . . . . . . . . . . . . 6 Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . . 7 DD Z Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Warming Blanket . . . . . . . . . . . . . . . . . . . . . . . 8 Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . . 9 DD Gradient Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11 So get ready for a more restful sleep. Warming Blanket . . . . . . . . . . . . . . . . . . . . . . 10 Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . 11 DDY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13 Warming Blanket . . . . . . . . . . . . . . . . . . . . . . 12 Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . 13 LED Throw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Auto-off feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-18 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 How to obtain warranty service . . . . . . . . . . . . . 20 DD Remote Features: • REMOTE CONTROL – sends heat level control commands to the base unit and adjusts the blankets warmth accordingly. • ELECTRONIC DIGITAL CONTROL – for easy setting with backlit LCD • AUTO-OFF – 10 hour independent auto-off (see page 15) • 10 TEMPERATURE SETTINGS – select your personal comfort • PRE-HEAT – for cozy warmth before bedtime • SOLID STATE – for accurate and consistent heat control • EASY OPERATION – Electronic digital controller for easy operation • EASY GRIP – ergonomic control for easy operation CAUTION: Do not plug main power cord into the wall outlet until you have completely set up your warming blanket per the instructions. IF YOU DO NOT FOLLOW THIS SEQUENCE, THE WARMING BLANKET WILL NOT WORK. • Disconnect power cord from wall before detaching control from warming blanket • Always make sure cords are NOT trapped or pinched between bed slats, mattress, springs, against wall, foot board or bed frame. Set Up • CORDLESS – no more wires to tangle • AUDIBLE BEEP – when changing heat settings, on/off setting and automatic programming selections. Pre-heat 1 To use the preheat feature, simply press the round “On/Off” button and then press the “Preheat” button. The preheat function will heat the bed for a period of 30 minutes. 2 To reset the preheat feature, simply press the “On/Off” button OFF. 3 To turn back ON repeat step1. WARMING BLANKET 1 Place the warming blanket on the bed with the label side facing outward. 2 Plug cord into the module at the bottom of the warming blanket until the plastic hinges click into place. CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could result from a loose connection. 4 Place the base unit on the floor under the bed. 5 Place the remote control where it is convenient for you. 3 Run the cord under the bed, not between the mattress and box springs. Avoid any tangling or pinching. 6 Plug warming blanket power cord into a 110-120 volt wall outlet. CAUTION: This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electrical shock, this plug is intended to fit only one way into an outlet. If the plug does not fit in the outlet, reverse the plug. Do not attempt to force the plug. IMPORTANT 1 Installing the Batteries 1 Remove the battery compartment door from the back of the remote control 2 Insert three AAA batteries, matching the + and - markings in the battery compartment to the markings on the batteries 3 Replace the battery compartment door 4 If your blanket has two remote controls, repeat steps 1 – 3 to install batteries in the second remote control. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate equipment. Using your Control: 1 To turn the control on, simply press the “On/Off” button. The backlit display light will illuminate and begin to warm at the comfort setting last used. CAUTION: ALWAYS turn the warming blanket “Off” when not in use. 2 To turn the warming blanket OFF simply press the “On/Off” a second time. Setting the control side (Queen or King blankets only) The “left” control can operate the left or both sides, and the “right” control can operate the right or both sides. (If you have a Twin or Full size blanket, the remote control operates the entire blanket.) Each person has complete control over his/her temperature comfort level for the ultimate in individualized comfort. You can use one remote control to operate both sides of the blanket (both sides of the blanket will have the same heat level). Or, you can use two remote controls to set separate heat levels for each side of the blanket. CAUTION: Do not plug main power cord into the wall outlet until you have completely set up your warming blanket per the instructions. IF YOU DO NOT FOLLOW THIS SEQUENCE, THE WARMING MATTRESS PAD WILL NOT WORK. • Disconnect power cord from wall before detaching control from warming mattress pad • Always make sure cords are NOT trapped or pinched between bed slats, mattress, springs, against wall, foot board or bed frame. Set Up WARMING MATTRESS PAD 1 Place the warming mattress pad on the bed with the label side facing outward. 2 Plug cord into the module at the bottom of the warming mattress pad until the plastic hinges click into place. CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could result from a loose connection. 4 Place the base unit on the floor under the bed. 5 Place the remote control where it is convenient for you. 3 Run the cord under the bed, not between the mattress and box springs. Avoid any tangling or pinching. 6 Plug warming mattress pad power cord into a 110-120 volt wall outlet. CAUTION: This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electrical shock, this plug is intended to fit only one way into an outlet. If the plug does not fit in the outlet, reverse the plug. Do not attempt to force the plug. IMPORTANT Features: • ELECTRONIC DIGITAL CONTROL – for easy setting with backlit LCD • AUTO-OFF – 10 hour independent auto-off (see page 15) • 10 TEMPERATURE SETTINGS – select your personal comfort • PRE-HEAT – for cozy warmth before bedtime • SOLID STATE – for accurate and consistent heat control • EASY OPERATION – Electronic digital controller for easy operation • EASY GRIP – ergonomic control for easy operation DD Convertible CAUTION: Do not plug main power cord into the wall outlet until you have completely set up your warming blanket per the instructions. IF YOU DO NOT FOLLOW THIS SEQUENCE, THE WARMING BLANKET WILL NOT WORK. • Disconnect power cord from wall before detaching control from warming blanket • Always make sure cords are NOT trapped or pinched between bed slats, mattress, springs, against wall, foot board or bed frame. On Off On Off Set Up • ROOM TEMPERATURE COMPENSATION – • INTERCHANGEABLE TOP – Pre-heat 1 To use the preheat feature, simply press the round “On/Off” button and then press the “Preheat” button. The preheat function will heat the bed for a period of 30 minutes. 2 To reset the preheat feature, simply press the “On/Off” button OFF. 3 To turn back ON repeat step1. WARMING BLANKET 1 Place the warming blanket on the bed with the label side facing outward. 2 Plug cord into the module at the bottom of the warming blanket until the plastic hinges click into place. CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could result from a loose connection. 3 Run the cord under the bed, not between the mattress and box springs. Avoid any tangling or pinching. 4 For dual control warming blankets, place primary control (label on back of control) on the same side of the bed as the blanket IMPORTANT label side. 5 For single control warming blankets, the control can be placed on either side of the bed. 6 Plug warming blanket power cord into a 110-120 volt wall outlet. CAUTION: This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electrical shock, this plug is intended to fit only one way into an outlet. If the plug does not fit in the outlet, reverse the plug. Do not attempt to force the plug. Using your Control: 1 To turn the control on, simply press the “On/Off” button. The backlit display light will reset itself by flashing “FF” and then will light showing the previous setting the unit was set during the last use and will begin to warm. CAUTION: ALWAYS turn the warming blanket/warming mattress pad “OFF” when not in use. 2 To turn the warming blanket/warming mattress pad OFF simply press the “On/Off” button. CAUTION: Do not plug main power cord into the wall outlet until you have completely set up your warming blanket per the instructions. IF YOU DO NOT FOLLOW THIS SEQUENCE, THE WARMING MATTRESS PAS WILL NOT WORK. • Disconnect power cord from wall before detaching control from warming mattress pad • Always make sure cords are NOT trapped or pinched between bed slats, mattress, springs, against wall, foot board or bed frame. On Off On Off Set Up WARMING MATTRESS PAD 1 Place the warming mattress pad on the bed with the label side facing outward. 2 Plug cord into the module at the bottom of the warming mattress pad until the plastic hinges click into place. CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could result from a loose connection. 3 Run the cord under the bed, not between the mattress and box springs. Avoid any tangling or pinching. 4 For dual control warming mattress pads, place primary control (label on back of control) on the same side of the bed as the IMPORTANT blanket label side. 5 For single control warming mattress pads, the control can be placed on either side of the bed. 6 Plug warming mattress pad power cord into a 110-120 volt wall outlet. CAUTION: This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electrical shock, this plug is intended to fit only one way into an outlet. If the plug does not fit in the outlet, reverse the plug. Do not attempt to force the plug. DD 2 7 DD Z 9 DD Gradient 10 11 DD Y 12 13 Features: • 3 TEMPERATURE SETTINGS – select your personal comfort level • SILENT OPERATION – no clicking • SOLID STATE – for accurate and consistent heat control • EASY OPERATION – electronic controller for easy operation • EASY GRIP – ergonomic control for easy operation • AUTO-OFF – 3 hour independent auto-off Auto-off control LED Throw CAUTION: Do not plug main power cord into the wall outlet until you have completely set up your warming blanket per the instructions. IF YOU DO NOT FOLLOW THIS SEQUENCE, THE WARMING THROW WILL NOT WORK. • Disconnect power cord from wall before detaching control from warming blanket • Always make sure cords are NOT trapped or pinched between furniture, walls or chairs. Power Cord Control Flag Tag Module 14 Throw Cord Label Throw Cord Connector Set Up Using your Warming Throw Control: 1 To turn the throw on simply press the round gray button. The indicator light will glow, depending on which setting the warming throw is set, and the warming throw will begin to warm. CAUTION: ALWAYS turn the warming throw “OFF” and disconnect the power cord from the outlet when not in use. 2 To turn the warming throw OFF simply press the round gray button through the different settings until the temperature setting lights are not glowing. WARMING THROW When setting up your warming throw, be sure to follow the steps below in order. 1 Locate the warming throw’s information label, located near the IMPORTANT module. 2 Firmly plug the warming throw cord into the module until the plastic hinges on each side click into place. CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could result from a loose connection. 3 Plug warming throw power cord into a 110-120 volt wall outlet. CAUTION: This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electrical shock, this plug is intended to fit only one way into an outlet. If the plug does not fit in the outlet, reverse the plug. Do not attempt to force the plug. Auto-off feature Auto-off Feature: The “Auto-Off” feature is designed for safety and conservation of energy by automatically turning your warming product off after 10 hours of continuous use. (Three Hours for Warming Throw) The Auto-off function engages 10 hours from the time the control is turned “On”. For Dual Control: Whichever control is turned On first that controls 10 hour Auto-off feature will be initiated. The controls Auto-off features work independently from each other. To restart after a power failure: Press the “On/Off” or “On” button, the blanket/mattress pad will begin to warm. Note: After a power outage, the “Auto-Off” feature automatically resets the timer. Auto-off Feature for Throw: The “Auto-Off” feature is designed for safety and conservation of energy by automatically turning your warming product off after 3 hours of continuous use. The Auto-off function engages 3 hours from the time the control is turned “On”. 15 Care and cleaning OF YOUR WARMING PRODUCT Taking care of your warming product is easy and safe as long as you follow a few simple steps. Caution: Always disconnect the power cord and the blanket/mattress pad/throw connection cord at the connection end before washing. Carefully follow all washing instructions or your warming product may shrink and possibly cause a fire hazard. DO NOT Caution: Do not use commercial dryers or the dryers at your local laundromat. They get too hot and would damage the wiring of the warming product. 1 Preheat the dryer on the low temperature setting for 2 minutes. 2 Place blanket/mattress pad/throw into the dryer and tumble dry for 10 minutes at a low temperature. • DO NOT dry clean your blanket/mattress pad/throw. Dry cleaning solvents may damage the warming element. 3 Remove the blanket/mattress pad/throw while it is still damp and gently stretch it to its original size. • DO NOT use bleach or cleaning fluids. • DO NOT use a wringer. 4 Continue to air dry over a clothesline or a shower rod. DO NOT use clothespins. • DO NOT iron the blanket/mattress pad/throw. 5 Warming product must be completely dry before using. • DO NOT use mothballs or sprays of any kind. • DO NOT turn the blanket/mattress pad/throw on until it is completely dry. 16 Machine Drying Hand Washing 1 Presoak the blanket/mattress pad/throw for 15 minutes in mild soap and lukewarm water. Machine Washing 2 Gently squeeze the soap suds through a few times. 1 Presoak the blanket/mattress pad/throw for 15 minutes in mild soap and lukewarm water. 3 Rinse in fresh, lukewarm water. 2 Wash in mild soap and lukewarm water on the delicate or gentle cycle in the washer for two minutes. Remember, do not use bleach. Hand Drying 3 Rinse in fresh, lukewarm water. 2 Air dry over a clothesline or hang over a shower rod. DO NOT use clothespins. 4 Spin dry in the washing machine. Then gently stretch to its original size. 3 Warming product must be completely dry before using. 1 Gently stretch the blanket/mattress pad/throw back to its original size. Frequently asked questions OF YOUR WARMING PRODUCT Q Who should NOT use the warming blanket, warming mattress pad, or warming throw? Q I have heard that some warming products have Electromagnetic Fields (EMFs). What is this? A The following people should NOT use the warming blanket, warming mattress pad, or warming throw: • An infant • A child • An incapacitated person • A paraplegic • A quadriplegic • A diabetic • Anyone insensitive to heat • Anyone who cannot clearly understand the instructions and/or operate the controls A EMF stands for Electromagnetic Field. This is an electrical field that surrounds any wire that has current flowing along its length. Although several studies have been conducted to evaluate the impact, EMFs have not been proven to be harmful. In any event, Sunbeam has reduced the strength of EMFs in its blankets/mattress pads/throws to very low levels. Q What do the Underwriters Laboratories (UL) or (ETL) labels mean? What do either of these labels mean about safety of Sunbeam warming products? Q My control feels warm to the touch: Is this a problem? A Underwriters Laboratories (UL) develops product safety standards for a large range of products and performs independent tests based on these standards. Products tested by UL and which have passed all the safety standards are permitted to bear the UL label. Intertek Testing Services (ETL) is a certified, independent testing organization that tests products in accordance with UL safety standards and issues the ETL label for those products that meet the relevant UL standards. All Sunbeam products are tested to UL standards and bear either the UL or ETL label to indicate that the product meets or exceeds UL/ETL safety standards for warming products. Q My warming product doesn’t operate. Q What do I do if my pet chews the cord, I lose my controller, or the controller does not operate properly? A Please stop using the warming product immediately. Call our Consumer Service number listed under How to Obtain Warranty Service and ask for instructions on how and where to send the warming product. A No. The control will feel warm to the touch when functioning properly. A Follow instructions on the flag tag. Unplug the system from wall outlet. Check that the control is well connected to the module. Plug the power cord into the wall outlet to reset the control. Press “On/Off” or “On” and set at the highest setting and wait 20 minutes. Try this twice. If the system still does not operate, disconnect the power cord and contact consumer service at the 800 number listed under How to Obtain Warranty Service. 17 Q My warming blanket/warming mattress pad/warming throw doesn’t heat properly. O n / O ff A Check to make sure the cord is plugged into the module and the power cord is firmly connected to the wall outlet. Check that the control is “On”. If the system still fails to heat, try the following test to see if it is operating. 1 Fold the warming blanket, warming mattress pad, or warming throw 3 times over. 2 Connect the control to the module and plug the power cord into an outlet. 3 Turn the control to the highest setting and wait five to seven minutes. 4 Put your hand between the folds and you should feel the blanket/ mattress pad/throw warming. Note: Remember, the warming product is not a heating pad. It will not feel hot to the touch when laid out flat in a normal manner. Caution: Do not continue the test for more than seven minutes. DO NOT attempt to make any internal adjustments to this appliance. If you have tried all of the solutions above and the warming product still doesn’t work, stop using it immediately, disconnect the power cord and contact our consumer service at the 800 number listed under How to Obtain Warranty Service. Q What does “FF” mean on my Electronic Digital Control? FF A The digital controls are designed to notify you in the event that a problem has been discovered by flashing “FF” on the display. Follow instructions on the flag tag to reset control. First, check the blanket/mattress pad for visual damage. If no visual Models DD3, DD2, damage is found, unplug the system from wall outlet. Check DDZ, DDW that the control is well connected to the module. Plug the power cord into the wall outlet. Set the control to “On.” If the 18 system still does not operate after 2 or 3 times trying to reset, disconnect the power cord and contact consumer service at 800-892-7684. Q What does a flashing light mean on my throw LED control or DD Gradient control? A The throw control and DD Gradient control is designed to notify you in the event that a problem has been discovered by flashing the light on the display. Follow instructions on the flag tag to reset control. First, check the blanket/mattress pad/throw for visual damage. If no visual damage is found, unplug the system from wall outlet. Check that the control is well connected to the module. Plug the power cord into the wall outlet. Set the control to “On.” If the system still does not operate after 2 or 3 times trying to reset, disconnect the power cord and contact consumer service at 800-892-7684. Q I have experienced some shedding of the fabric fibers of my warming blanket/warming throw, what do I do? A Shedding is normal. If it becomes bothersome, follow the use and care instructions to wash and dry your warming blanket/warming throw. Limited Warranty Sunbeam Products Inc. (“Sunbeam”) warrants that for a period stated below from the date of purchase, this product will be free from defects in material and workmanship. • Warming Blankets branded Sunbeam® Imperial Court™, Elite™, Dynasty Nights™, SlumberRest Arctic Dawn™, Nordic Dreams™, Winter Oasis™, Basic™ and Northern Illusions™, and Sunbeam® The Blanket with a Brain® will carry a FIVE year limited warranty. • Warming Blankets branded Sunbeam® Select™ will carry a TWO year limited warranty. • Warming Blankets branded Arlington™ will carry a ONE year limited warranty. • Warming Mattress Pads branded Sunbeam® Palace Comfort™, Winter Sunrise™ and Midnight Retreat™, SlumberRest® Midnight Sun™ and Glacial Retreat™, and Sunbeam® The Mattress Pad with a Brain® will carry a FIVE year limited warranty. • Warming Mattress Pads branded Arlington™ will carry a ONE year limited warranty. • Warming Throws branded Sunbeam® Select™, Cuddle-Up™, SlumberRest® Cuddler™, and Sunbeam® The Throw with a Brain® and Sunbeam® American Heritage Collection™ will carry a TWO year limited warranty. • Warming Throws branded Arlington ™, will carry a ONE year warranty. Sunbeam, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar product of equal or greater value. This is your exclusive warranty. This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. Sunbeam dealers, service centers, or retail stores selling Sunbeam products do not have the right to alter, modify, or any way change the terms and conditions of this warranty. This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than Sunbeam or an authorized service center. Further, the warranty does not cover Acts of God, or Nature, such as fire, flood, hurricanes and tornadoes. Sunbeam shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty. Except to the extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty. Some states, provinces or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or province to province. 19 How to obtain warranty service: We’re Here to Help. For any questions you may have about your warming product, please contact Sunbeam Consumer Service: 1-800-892-7684, or write with product questions to: SUNBEAM CONSUMER SERVICE P.O. Box 948389 Maitland, FL 32794-8389 or visit our web site at: www.sunbeambedding.com. To return your product for repair or replacement: Please attach a tag to the product (do not use pins) that includes your name, address, daytime telephone number, and description of the problem. Please include a copy of the original sales receipt. Carefully package the product. Please use UPS or Parcel Post, with shipping and insurance prepaid to: SUNBEAM PRODUCTS, INC. Blanket Service Station P.O. Box 469 224 Russell Drive Waynesboro, MS 39367 DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE. ©2003 Sunbeam® is a registered trademark of Sunbeam Products, Inc. Distributed by Sunbeam Products, Inc., 2381 Executive Center Drive, Boca Raton, FL 33431 20 RPOB 9/02 021 T STAMP HERE PLACE FIRST-CLASS ▲ PLEASE FOLD AND SEAL WITH TAPE BEFORE MAILING. DO NOT STAPLE. REGISTER ONLINE AT: WWW.SUNBEAMBEDDING.COM ▲ We value your input! Your responses will help us bring you new products specifically designed to meet your needs. HELP US DEVELOP NEW PRODUCTS: We will keep the model number and date of purchase of your new Sunbeam product on file to help you refer to this information when necessary. PROTECT YOUR PRODUCT: Your prompt product registration confirms your right to the protection available under the terms and conditions of your Sunbeam warranty. CONFIRM YOUR WARRANTY: Complete the attached registration card and return today to receive these 3 important benefits: PRODUCT REGISTRATION CARD !802014236365! PRODUCT REGISTRATION DEPARTMENT PO BOX 44236 DENVER CO 80201-4236 Please do not send products or other correspondence to this address. ▲ Day Year 3. Warming throw .00 A. Everyday Last name: 15 16 17 18 19 Apt number: Month 021 T Year 2. Single 2. Female Day 1. Married 1. Male Your marital status: Your gender: Date of your birth: (Examples: 01, 02, 03, 04...) Including yourself, what is the total number of people living in your household? Month Year Year Male Female 1. 2. 1. 2. Month Month Year Year Date of birth (month/year) of the other adults and children in your household: Male Female 1. 2. Month Books/magazines Children’s products Clothes Insurance/financial products Music/video/DVD Travel Other I use these credit cards: 1. American Express 2. Gas/Retail 3. Master Card 1. 2. 3. 4. 5. 6. 7. B. Internet 4. Visa 5. Other_____________ 6. Do not have credit cards A. Mail In the last six (6) months has anyone in your household purchased any of the following items through the mail and/or over the internet? Education: (Please check which category applies to you): 1. Some high school 3. College degree 2. Completed high school 4. Graduate degree For your primary residence, do you: 1. Own 2. Rent 1. 2. 20 21 22 23 24 ▼ Initial: State: Zip code: Please fill-out and return this card within 10 days! We appreciate your responses to this questionnaire and the information you provide will be used by us and our marketing partners to offer you product information and other communication that may interest you. This information in no way will have an effect on your warranty terms. ▼ First name: Address: (number and street) City: E-mail address: (EXAMPLE: yourname@yourhost.com) Month 1. Yes! I want to receive offers or communications from Sunbeam via e-mail. 2. Yes! I want to receive offers or communications that may interest me from other companies via e-mail. I understand this e-mail address may be shared with and/or combined with information from other sources. Date of purchase: Product purchased: 1. Warming blanket 2. Warming mattress pad Style number: Purchase price: Store where purchased: Please describe this purchase: 1. A first time purchase 2. A replacement to this brand 3. A replacement of another brand 4. An additional purchase 5. Received as a requested gift 6. Received as a surprise gift How did you first learn about this product? 1. Inside the store 3. News story-public relations 2. Advertisement 4. Trusted brand What do you consider the most important factors influencing your decision to purchase this warming product? 1. Color/style 7. Warranty 2. Replacement of existing 8. Auto-off feature 3. Value for price 9. Large number of heat settings 4. Friend/relative’s 10. Energy savings recommendation 11. Cold weather 5. Advertising 12. Gift for someone else 6. Brand name I trust 13. Other_______________ In the winter In the fall In the spring In the summer How often do you turn on/plan on turning on your warming product (using its heating capacity)? (Check all that apply) B. Once C. Once a week a month 1. 2. 3. 4. What is the approximate temperature your home thermostat is set to through out the night during winter? 1. Under 55 4. 66-70 2. 56-60 5. 71-75 3. 61-65 6. Over 75 How often do you purchase this type of product? 1. Received as a gift 4. Every 4-5 years 2. First time purchase 5. Every 6-9 years 3. Every 1-3 years 6. Every 10+ years Someone in my home participates in the following activities: (Check all that apply) 1. Crafts 10. Outdoor activities 2. Cultural arts/events 11. Own a pet 3. Do-it-yourself 12. Personal computing 4. Enter sweepstakes/contests 13. Read books 5. Finance/investments 14. Self improvement 6. Fitness/excercising/jogging 15. Sports 7. Gardening 16. Travel 8. Gourmet cooking 17. TV shopping 9. Home decorating 18. Watch sports on TV ▼ 10 11 12 13 14 Which of the following products do you have or plan to own? 1. Warming blanket 3. Electric throw 2. Warming mattress pad PLEASE FOLD AND SEAL WITH TAPE BEFORE MAILING. DO NOT STAPLE. Thank you! We appreciate your responses to this questionnaire. The information you choose to share with us will be used by us and our marketing partners to offer you product information and other communications that may interest you. If you prefer not to be contacted about these special offers, please check here RPOB 9/02 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2003:05:15 11:17:26Z Modify Date : 2003:06:11 11:49:25+08:00 Page Count : 25 Creation Date : 2003:05:15 11:17:26Z Producer : Acrobat Distiller 4.0 for Macintosh Mod Date : 2003:06:11 11:49:25+08:00 Metadata Date : 2003:06:11 11:49:25+08:00EXIF Metadata provided by EXIF.tools