Sungjin Techwin MHF-R330BT BLUETOOTH REARVIEW MIRROR HANDS-FREE CAR KIT User Manual 2 of 2

Sungjin Techwin Co., Ltd. BLUETOOTH REARVIEW MIRROR HANDS-FREE CAR KIT Users Manual 2 of 2

Contents

Users Manual 2 of 2

Installation on the HandsFree KitInstallation on the HandsFree KitBluetooth HandsFree Car Kit①On the back of the MHF-R330BT unit you will see two pairs of clips. Place the bottom pairof clips on the underside of your existing rearview mirror. Lift the unit so that the bottomclips extend allowing the top clips to be fixed in position on top of your Rearview mirror and securely hold the handsfree unit in place. Adjust the fitted unit to your preference forclear rear vision.②Select a suitable position for the microphone depending on your vehicle type, this shouldbe placed close to the users head - the driver’s sun visor is normally adequate. “It is highly recommended to have the front of the microphone (side with more holes) directly facing the operator for the best voice pickup.” The microphone can be placedeither back or front of the visor by detaching, rotating and re-attaching microphone holderto correct side of the microphone.③Clip a microphone on the driver’s sun visor recommended to keep a distance of the microphone from the MHF-R330BT unit as long as possible.④Insert the power jack of the power adapter cable (4M).⑤Connect the Power Adapter Cable into its respective socket on the MHF-R330BT unit.⑥The power lead should be secured and hidden into the vehicles interior using the seals orjoins around the windscreen and door “A-Frame” and under your dashboard. Ensure thatyou leave yourself enough cable to be able to connect to your cigarette lighter socket.Note : Please ensure that the microphone and power cable do not interfere with the safeoperation of your vehicle.Installation guide67Part description (Bluetooth handsfree car kit)D.C Power Input - Connect to the cigarette lighterUSB Upgrade Port - For firmware upgradeSpeaker - The back sideCaller ID Indicators - 12 digits (phone with handsfree profile required)LED Indicators - 4 LEDs - Light on (during handsfree use)Bluetooth Link LED - Light twinkling (Pairing mode)Light on (Bluetooth mode)VOL ▲▲/ ▼▼- For adjusting the loudspeaker volume up / down- Also used during the initial set up and pairing processSEND - Controls ‘Answer & Talk’, ‘Redial’, ‘Voice Dialling’ and ‘Pairing re-activation’END - ‘End’, ‘Reject’ and ‘Audio transfer’ MUTE - Switches OFF built-in loudspeaker allowing private conversation when optional earphone. (not included)EAR - Earphone plug in
Installation on the HandsFree KitInstallation on the HandsFree Kit89Power On : It appears start on the mirror.2. You will hear a beep tone. The HandsFree unit is now ready to be paired for the first time.It appears Pairing HF on the mirror.3. For the next procedure, Go to the next page to follow the instruction of ; The MHF-R330BT supports both HandsFree and Headset Profiles. The default profile isHandsFree. Follow the pairing instructions for the first use, after that the unit will pairautomatically.1. When the power is on, press the “VOL ▲▲” button for 3 seconds.Pairing your Bluetooth cellular phone with the MHF-R330BTPairing in “HandsFree” mode2. You will hear a second beep tone, which shows the unit is ready to be paired for the first time.It appears Pairing HS on the mirror.The “Headset” mode does not support ‘Caller ID’, ‘Voice Dialling’ and ‘Reject Call’1. After the above 1~2, then press the “VOL ▲▲” button for 3 seconds again.Pairing in “Headset” modeCellular phone pairing mode (Next page)3. For the next procedure, Go to the next page to follow the instruction of ; Voice : “Power On” Go toCellular phone pairing mode (Next page)Go to1. Browse your cellular phone menu and find the connectivity and / or Bluetoothconnection section.2. Select the “search for” a new HandsFree device function and allow the phone to findthe MHF-R330BT.Note : Each cellular phone type has distinct phone menu so you may need to refer toyour manufacture’s instructions for the correct procedure on how to “connecta new Bluetooth device”.3. The Bluetooth code for the MHF-R330BT should appear on your cellular phone screen.4. Press the “connect” with the HandsFree option on your cellular phone.Note : Please return to the pairing instructions if the Bluetooth code does not appearon the cellular phone screen. The green LED light should flash during pairing.5. The cellular phone should prompt for a pin code. Insert the MHF-R330BT pin code :6. The cellular phone should confirm that it has established a new paired connection.7. Close the menu. The pairing is now completed.Note : The green LED light illuminates after successful pairing. Please adjust the volume to your preference by using the volume keys.Cellular phone pairing modeNo Bluetooth connection :No Phone on the mirror.Send call :Calling on the mirror.●ModooFree Plus BT can be stored up to 4 different phones.●The earliest phone number will be removed when the memory is full.● The Pairing Priority will be given to the last paired cellular phone. ●If you want to change the pairing priority, try to connect ModooFreePlus BT from the cellular phone.Pairing can be stored up to 4 cellular phones. It appears Paired on the Mirror.1 2 3 4 Voice : “Connected” 󳃈Press “SEND” button in order to reactive Bluetooth pairing link.MUTE :Secret on the mirror.
Installation on the HandsFree KitInstallation on the HandsFree KitDouble click “SEND” button connecting to the second call. It appears Redial on the mirror.Note : This function only works if you have a callwaiting option with your carrier and also another call is actually waiting to be answered.Call waitingPress “SEND” buttonIt appears Redial on the mirror.Note : This function only worksif phone has “last number redial” feature.Last number dialling during idlePress and hold “SEND” button (for 2 seconds)It appears Voice Dial on the mirror. Announce name after a beep.Note : Voice dialling is possible only if your cellularphone has a voice dialling capability. Each cellular phone type has distinct phone menu so you may need to refer to your manufacture’s instructions.Voice Dialling during idleThe audio transfer function is for switching the call from the HandsFree unit to thecellular phone for a private conversation without disconnecting the call. Switching from HandsFree to cellular phone :Press and hold “END” button (for 3 seconds)Switching back to HandsFree : Press and hold “END” button (for 3 seconds)It appears Call Trans on the mirror.Audio transfer1011NOTE : Once the Bluetooth pairing is completed between your cellularphone and MHF-R330BT, the both units will be automaticallyrecognized on its pairing whenever turn on the key in your car.To accept callpress “SEND” buttonIt appears Accept Call on the mirror.When the handsfree is ringing with incoming callTo reject callpress “END” buttonIt appears Drop Call on the mirror.To change handsfree ring tone ( 3 Ring Sound Options + 1 Voice )press and hold “VOL ▼▼” button for 5 seconds.Display will show Elod 1, 2, 3. or O.Set to your chosen option by repeating same procedure.To end callpress “END” buttonIt appears Drop Call on the mirror.During conversationTo control volumepress “VOL ▲▲” / “VOL ▼▼” buttonIt appears Vol Up or Vol Dn(down)on the mirror.Using the MHF-R330BT as a HandsFree DeviceUseful Tips for Bluetooth Connection1.Should your cellphone battery be at low charge, the Bluetooth connection may occasionally be lost.To maintain good connectivity ensure that your phone battery is adequately charged.2. In case of failure of Bluetooth pairing 1) Delete item in paired list on your Bluetooth phone 2) Reset both phone and handsfree by switching off /on 3) Reset pairing as per procedure 3. Connection not established after pairing󳃈Manually connect from the paired phonei.e. My paired devices 󳃬MHF-R330BT 󳃬Connect4. How to establish re-connection after pairing󳃈Press "SEND" button briefly󳃈Press and hold "END" button for 5 secondsThe handsfree unit will re-connect automatically thereafter.※※No voice announcement from the handsfree 󳃈Set cellular phone profile to Vibration / Silent mode.
Installation on the Parking SensorsInstallation on the Parking SensorsThis manual is intended to explain the safe and correct use of the product.Please read this manual carefully before use.Installation on the HandsFree KitHandsFree Call (Send Call) in the CarPress phone number on the cellular phone, and press “SEND” button of HandsFree.Note : If there is no sound on the loudspeaker of HandsFree unit, press and hold“END” button for 3 seconds. Then, it will switch from Cellular Phone to HandsFree. Private conversation option:The operator can plug an earphone (not included) in to the earphone jack of theMHF-R330BT for a private conversation.Note : For your own safety, it is highly recommended that the vehicle is parked inthe safe place when plugging in the earphone.Re-activation of Bluetooth Link after Pairing󳃈Press “SEND” button. ( If Bluetooth Link LED is turned off, press “SEND” buttonin order to reactivate the Bluetooth pairing link )Please note ;It is possible that the MHF-R330BT buttons might not operated as per thisoperation guide if your Bluetooth phone has an unusual Bluetooth program.In this case, please reset both MHF-R330BT and cellular Phone.Specification (HandsFree Car Kit)Input powerNormal CurrentMaximum CurrentFuseSpeakerMicrophoneNoise SuppressionEcho SuppressionOperating temperature rangeSupported Profiles Power Class Carrier FrequencyBuilt in Flash memoryCompatibilityFull duplex operation with noise & echo suppressionBluetooth specification: v1.2 compliant10 ~ 16V DC > 50mA> 500mA250V / 2AMax. 2WDirectional microphone -52dBUp to 18dBUp to 42dB- 30°C ~ + 80°CHandsfree Profile, Headset Profile2dBm Max (Class 2) 2400MHz ~ 2483.5MHz8M bitThis unit is compatible with most Bluetoothequipped cellular phones including Motorola,Sony Ericsson and Nokia, Samsung, LG, Etc.(Most Bluetooth enabled phones)Product OverviewThe Parking Sensor helps the driver view the rear of the vehicle. It helps prevent collisions andaccidents during any backward movement of the vehicle. If there is an obstacle at the rear of thecar, the alarm inside the vehicle displays the distance to the obstacle and generates a signalproportional to it.Features of the Product- Enables safe backward movement by detecting obstacles in the rear.- Insures a safe distance in the event of snow, rain, frost or fog.- Insures a safe distance between an obstacle and the rear of the vehicle while parking and stopping.- Easily installed and semi-permanent.- Good design which matches the vehicle (Attach Type sensors).- Displays the distance to the obstacle from the back of the vehicle while backing-up within 0.4m.- Informs the driver of the proximity of obstacles on the left and right sides of the vehicle.- Generates a four-level alarm signal depending on the distance to the obstacle.Method of OperationThe Parking Sensor beeps and the distance meter displays as "0.0" as soon as you engage thereverse gear. An alarm is generated if an obstacle is detected within the first-level detection area(within 1.6m), and the distance meter displays the distance to the obstacle. The alarm changesas the obstacle approaches the second-level (within 1.0m) and third-level (within 0.6m)detectionarea. When the obstacle is within 0.4m, a continuous alarm is generated. If the driverdoes not hear the alarm due to noise or weak hearing ability, the distance meter and theleft/right lamps indicate the proximity of the obstacle.With a built-in Parking Sensors by ultrasonic sensors inside the rear mirror, while backing thevehicle, the sensor senses the distance from the right, left, rear and indicates the distance viaLED digits (0.4m~1.6m) & left & right and also by four stages of warning signals(beep sounds)which helps the driver while backing the vehicle. 12 13
Installation on the Parking SensorsInstallation on the Parking SensorsCar Installation▶▶Installation of SensorsConnecting the parking system to the ModooFree Plus BT.- Install the control box at the left and right sides of the rear seat beyond the reach of passengers' hands.- Pull the main cable out of the windshield or pedal and connect it to the control box.- Connect the sensor cable and the power cable to the control box.- Use the cable-tie to organize the loose cables.Installation Method※Caution : The sensor may be positioned upside down.Apply the Two-sided tape to the sensor attachment. Attach the sensor to the trunk or rearlights at about 50~80cm(20"~32") (normally 60cm(23.5")) from the center of the car.Installed Exterior of the Attach-Type Sensors (two ways)After attaching the sensor, attach the mount to the trunk and fix the sensor cable with the cable tie. Then, pull the sensor cable to one side of the trunk and put it in the control box.Organizing the Sensor Cable (two ways)Product InstallationConnect the power cable.Generally, black cables are (-) in vehicles. In the case of the ModooFree Plus BT Cable, do notpeel off the cable covering - connect it using a line connector.※Caution : Beware of the (±) polarity.Connecting the Power CablePart description (Parking sensor kit)Detection LED Indicators- Left (●) and Right (●)Distance Indicators- Distance via LED digits (0.4M ~ 1.6M)Specification (Parking Sensors)Input powerEjection Molding MaterialDetectionUltrasonic Frequency Operating TemperatureLength of Main CableLength of Sensor CablesLength of Power Cable12V~24V DC (Free Voltage)ABSUltrasonic Sensors40KHZ- 20。C ~ + 65。C7m3m3m14 15
Installation on the Parking SensorsInstallation on the Parking SensorsDetection distance- It is better to arrange the cables along the left side of the frame (by the driver's seat).- Make certain that water cannot contact the sensor while driving.- The main cable should be long enough to compensate for the contours of the driver's seat.- The main cable should be kept away from the engine, if possible.The sensor horn should always be in a horizontalposition.Bracket Attachment※※Attaching to Other Types of Vehicles (For trucks and tow trucks)Bore two holes on the left and right sides witha drill, so that the bracket can be fixed withscrews.Attach at the center for a 1-tontruck, and at the rear gutter for a larger truck.Attach the ModooFree Plus BT body ontothe existing rearview mirror.Fix the connector at the parking sensor plug of the ModooFree Plus BT.Fix the connector with the control box label at one side of the alarm cable (7m) to the control box connector.Attaching the Main UnitⓑⓑPut up the power cable in the line connecter as “ⓐⓐ”ⓒⓒPress the clip with a long nose plier.ⓓⓓClose the door of line connector. Use of the Line ConnectorⓐⓐⓑⓑⓒⓒⓓⓓAttach the sensor to the rearlight using a bracket.16 17
ModooFree Plus BT ; MHF-R330BTBluetooth Parking Sensors HandsFree Car Kit▶▶Bluetooth HandsFree Car KitNo indication from unit?There is a chance the power cable plug is not correctly seated in the cigar/utility jack socket forproper connection. Remove and reinsert to ensure good fitting and connection. Problem during pairing?Repeat pairing process according to the pairing sectionStill experiencing problem? Turn off the cellular phone and separate the battery from the cellular phone for approximately fiveseconds (In some instances, this action clears up any potential bugs built up in the cellular phonesoftware that can hinder proper pairing.) Repeat pairing process as per previous pairing instructions. Too loud?Adjust the volume to your preferred sound level by pressing the relevant volume switch.Each type of Bluetooth cellular phone has different function buttons, thoughhighly unusual, it may be possible that the functions operate differently withyour specific phone model.Callers are complaining about hearing noise?Check that the microphone is secured firmly in place and is not creating vibration and noise. Alsocheck and adjust microphone accordingly to ensure that it is facing towards to the user’s face.▶▶Parking Sensors KitThe sensor does not work while engaged in "Reverse".- Check to see if the power cable is connected to the rear light.- Check to see if the power cable and the alarm cable are connected to the alarm.The sensor does not detect obstacles. Only (0.0) is displayed.- Check to see if the sensor cable and alarm cable are connected.- Check to see if the alarm cable is connected to the alarm.- Check to see if the sensor is obstructed by dirt.- Check to see if any sensor is detected with the earth.Troubleshooting- Do not expose this unit under humid environment.- Do not drop this unit. - Do not disassemble this unit.- Do not press two buttons at once. This action may cause a sudden Bluetooth disconnection. - Do not clean the unit with any chemical or water.- Keep this unit away from fire and dust.- For safety reasons, please keep your phone conversation short, do not make any notes or readdocuments. It is highly recommended to park the vehicle in the safe place before continuing theconversation. Using a cellular phone while driving can potentially create a distraction for thedriver which may increase the likelihood of an accident.- Please adjust direction of the mirror to ensure good rearview vision for safe driving.- Use the third-level alarm only when the obstacle is located in a straight line from the vehicle.- Attach the sensor level with the ground surface.- Keep water away from the alarm (ModooFree Plus BT).- Thin rods or objects, objects with a high tint angle, and sound-absorbing objects cannot be detected.- Beware that the power cable or sensor cable may be cut if excessive force is used during installation.- The area just under and to the right and left ends of the rear bumper cannot be detected.Safety precautionsSungJin Techwin Co., Ltd. warrants to purchaser that for a period of one (1) year after the date ofpurchase (the “Warranty Period”) of any SungJin Techwin Co., Ltd. Product by Purchaser, the productwill substantially conform to SungJin Techwin Co., Ltd. published specifications for the product on thedate of purchaser’s purchase of the product, subject to the terms herein. Purchaser shall notify SungJinTechwin Co., Ltd. of any non-conformance during the warranty period and obtain a written returnmaterial authorization (“RMA”) from SungJin Techwin Co., Ltd. for the nonconforming product and returnthe nonconforming product to SungJin Techwin Co., Ltd., freight prepaid with a statement describing thenonconformity. SungJin Techwin Co., Ltd. exclusive obligation with respect to nonconforming productshall be, at SungJin Techwin Co., Ltd.’s option and expense, to repair or replace such returned item. Theforegoing is purchaser’s sole and exclusive remedy for breach of warranty by SungJin Techwin Co., Ltd.’swith respect to the product. The warranty set forth above shall not apply to any product, which has notbeen properly used or handled in accordance with the instructions supplied by SungJin Techwin Co., Ltd.In addition, SungJin Techwin Co., Ltd.’s warranty is void if the product has been repaired, altered,damaged by the faulty installation, misuse, abuse, or which the product defect is attributable to anyfailure or damage which is beyond the reasonable control of SungJin Techwin Co., Ltd. This warrantyapplies only to new SungJin Techwin Co., Ltd. products purchased from authorized retail sellers only.The foregoing warranties are the sole warranties, express or implied, given by SungJin Techwin Co., Ltd.in connection with the product, and SungJin Techwin Co., Ltd. disclaims all other warranties, includingwarranties of merchantability, fitness for a particular purpose and no infringement of third party rights. SungJin Techwin Co., Ltd. shall not be liable for any special, incidental or consequential damages inconnection with the product, even if SungJin Techwin Co., Ltd. has been advised of the possibility of suchdamages. The liability of SungJin Techwin Co., Ltd. hereunder for all claims shall not exceed the amountpaid by purchaser to SungJin Techwin Co., Ltd. for the product sold rise to SungJin Techwin Co., Ltd.’sliability.WarrantyMemo18 19

Navigation menu