Sunmi Technology V2 T5930 User Manual 04 T5930 UM 20190129

Shanghai Sunmi Technology Co.,Ltd. T5930 04 T5930 UM 20190129

Contents

04 T5930 UM_20190129

请自行添加一维码内容为说明书料号List of packaged itemsTerminal device × 1User's Guide × 1Charger & Adapter × 1USB Cable × 1Wi-Fi Build-in Wi-Fi 802.11a/b/g/n(2.4G/5G)Camera 5M AF / （0.3M FF optional）FLASH 8GB Nand FlashCPU frequency 1.3 GHz Quad CoreKeys Power key, volume keyDisplay 5.45 inch IPS, resolution 1440×720Operating system SUNMI OS 2.0 (based on Android 7.1)Bluetooth Support Bluetooth 4.0RAM 1GB LPDDR3Interfaces USB Type C， Nano SIMPrinter type Thermal PrinterPrinting paper specifications Width 58mm, maximum diameter 50mmTouch screen Capacitive ScreenWireless data2G：B2/B3/B5/B83G：WCDMA(B1/B2/B4/B5)4G：B2/B3/B4/B7/B17/B28Item Technical SpecificationsBattery 7.6V/2580mAhOutline dimensions L 219.1mm ×W 80mm ×H 17.8mmAdapter OUTPUT：DC5V/2A INPUT：AC100~240V/0.3A 50/60HzUser GuideT5930 Technical specificationsName of partsCircuit board(Pb) (Hg) (Cd) (Cr(VII) (PBB) (PBDE)Toxic and harmful substances and elementsShell:It indicates that the content of toxic and harmful substances in all homogeneous materials of this part is below the limit specified in SJ/T11363-2006.:It indicates that the content of toxic and harmful substances is higher than the limit specified inSJ/T11363-2006 in at least one homogeneous material of this part; however, the the reason why the toxic substance of that part exceeds the limit is that there is no applicable material to replace it currently. For products that have reached or passed the service years for environmental protection, they should be recycled according to Measures for Control and Management of Electronic Information Products and should not be thrown away at will.Name and content of toxic and harmful substances contained in this product are shown in the following tableManufactureShanghai Sunmi Technology Co.,Ltd. Room 505 No.388 Song Hu Road Shanghai, ChinaThis product can be used across EU member states.The full text of the EU declaration DOC is available at the following internet address：www.sunmi.comTechnical features and characteristicOperation Frequency824-849 MHz(Tx),869-894 MHz(Rx)1850-1910 MHz(Tx),1930-1990 MHz(Rx)1850-1910 MHz(Tx),1930-1990 MHz(Rx)1710 -1755 MHz(Tx),2110 - 2155MHz(Rx)824-849 MHz(Tx),869-894 MHz(Rx)1850-1910 MHz(Tx),1930-1990 MHz(Rx)1710-1755 MHz(Tx),2110-2155 MHz(Rx)2500-2570 MHz(Tx),2620-2690 MHz(Rx)704-716 MHz(Tx),734-746 MHz(Rx)2412-2462 MHz2402-2480 MHz2402-2480 MHz5150-5250 MHz5725-5850 MHzTransmitted32 dBm30 dBm23 dBm23 dBm23.5 dBm22.5 dBm22.5 dBm22.5 dBm23 dBm15 dBm6 dBm6 dBm17 dBm16.5 dBmThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference. (2) This device must accept any interference received, includinginterference that may cause undesired operation.FCC ID: 2AH25V2NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:---Reorient or relocate the receiving antenna.---Increase the separation between the equipment and receiver.---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.---Consult the dealer or an experienced radio/TV technician for help.Body-worn OperationThis device was tested for typical body-worn operations. To comply With RF exposure requirements, a minimum separation distance of 1.0cm must be maintained between the user’s body and the handset, including the antenna.Third-party belt-clips, holsters, and similar including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should beavoided.Specific Absorption Rate (SAR) information:This wireless phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.FCC RF Exposure Information and Statement. The SAR limit of USA (FCC) is 1.6W/kg averaged over one gram of tissue.Device types: T5930 has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification when properly worn on the body is 1.856W/kg（10gSAR， test distance：10mm，limit 4W/kg）and 1.276W/kg (1gSAR， test distance：10mm，limit 1.6W/kg). This device was tested for body-worn operations with the back of the handset kept 10mm and 5mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10mm and 5mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.GSM 850GSM 1900WCDMA BAND IIWCDMA BAND IVWCDMA BAND VLTE BAND 2LTE BAND 4LTE BAND 7LTE BAND 172.4G Wi-FiBluetoothBLE5G Wi-Fi5G Wi-Fi
Printing instructionsThis device supports 58mm thermal paper with the specifications of 57±0.5mm*Ø50mm· Please open the paper container with the uncovering handle (as shown in Fig.1). Please do not force open the paper container to avoid print head gear wear;· Feed the paper correctly into the paper container in the direction as shown, and pull some paper outside the cutter (as shown in Fig.2);· Close the cover of the paper container to finish printing paper feeding(as shown in Fig.3).Note: If the printed paper is blank, please check whether the paper roll has been installed in the correct direction.Type-C USBPower OutletCharger & AdapterProduct DescriptionVolume keyPower key+-PrinterType-C USBOpening handleCameraSpeakerExtended interfaceSIM Card SlotExtremely easy settingsOnly a few steps to activate an intelligent business device①Set 2G/3G/4G: when power off, insert the 2G/3G/4G card and then power on.(Refer to the Technical Specifications for the support of cards)② Long press the Power Key for 2~3s to activate the backlight of screen,and then operate following the prompts after entering the startup/booting screen for the first time. 2 modes for accessing the Internet are available.③ Set WiFi· Click "Set" button, activate "WLAN" to enter the WLAN searching screen, and wait it to list all useable WLAN hot spots;· Click the WLAN to be connected, and enter the access password in case of an encrypted network. Download/use AppsAfter connected to the Internet, open the App Market, find, download and install the Apps.FAQBooting failure (e.g. low battery)· Plug the USB cable and charge for 3min;· Check if the screen displays the normal charging status.System crash· Long press the Power Key for 11s to reboot.Read the installed Help App for more informationBattery coverNano SIM321Power keyShort press: wake up the screen, lock the screen.Long press: long press for 2-3 seconds in power off mode to switch on the device. Long press for 2-3 seconds in normal operation mode to select power off or reboot. Long press for 11 seconds when system is frozenfor automatic reboot.Volume keyVolume adjustment.PrinterFor printing sales slips in power on mode.Type-C USBFor device recharging and developer debugging.CameraFor payment scanning and 1D/2D code quick scanning.SIM Card SlotNote: To prevent system errors, please make sure the device is turned off when you insert or remove the SIM card.Instructions for recharging and batteryThis device supports charging only by USB cable· Connect the 5V adapter to the power supply socket;· Connect the USB cable to the USB interface of the device for recharging; · The screen will display the recharging icon during the recharging process;· If the recharging icon does not appear, please check whether the USB interface is well connected.Instructions/Notes for battery· This device adopts 7.6V/2580mAh lithium battery; please do not disassemble the battery.· In order to protect the battery life, we recommend that yourecharge the device whenever possible, and please do not allow the battery to fully drain before recharging.PrecautionsSafety Warning· Connect the AC plug to the AC socket corresponding to the marked input of the power adapter;· Do not use in the presence of any potentially explosive gas;· To avoid injury, unauthorized persons shall not open the power adapter; · This is a Class A product. This product may cause radio interference in living environments. In that case, the user may be required to take adequate measures against interference. · Battery replacement: 1. Explosion danger may arise if replacing with the wrong battery! 2. The replaced battery shall be disposed of by maintenance personnel,and please do not throw it into fire!Significant Safety Instructions· This terminal is a handheld device, and the user shall protect the password from being peered at by others while entering the password;· Do not install or use the device during lightning storms to avoid the potential risks of lightning shock;· Please turn off the power immediately if you notice abnormal odor, heat or smoke;· The paper cutter is sharp, please do not touch!Suggestions· Do not use the terminal near water or moisture to prevent liquid from falling into the terminal;· Do not use the terminal in extremely cold or hot environments, such as near flames or lit cigarettes;· Do not drop, throw or bend the device;· Use the terminal in a clean and dust-free environment if possible to prevent small items from falling into the terminal;· Please do not use the terminal near medical equipment without permission.StatementsThe Company does not assume responsibilities for the following actions: · Damages caused by use and maintenance without complying with the conditions specified in this guide;· The Company will not assume any responsibilities for the damages or problemscaused by optional items or consumables (rather than the initial products or approvedproducts of the Company). The customer is not entitled to change or modify the product without our consent.· The product’s operating system supports official systemupdates, but if you change the operating system into a third party ROM system or alter the system files by system cracking, it may cause system instability and security risks and threats.DisclaimerAs a result of product upgrading, some details in this document may not match the product, and the actual product shall govern. The Company reserves the right of interpretation of this document. The Company also reserves the right toalter this specification without prior notice.

Navigation menu