Sunmi Technology V2 T5930 User Manual 04 T5930 UM 20190129
Shanghai Sunmi Technology Co.,Ltd. T5930 04 T5930 UM 20190129
Contents
- 1. 04 T5930 UM_20190129
- 2. T5930 UG
- 3. User Manual
04 T5930 UM_20190129
Technical specifications This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. Item Technical Specifications Operating system SUNMI OS 2.0 (based on Android 7.1) CPU frequency RAM FLASH 1.3 GHz Quad Core 1GB LPDDR3 8GB Nand Flash (2) This device must accept any interference received, including interference that may cause undesired operation. FCC ID: 2AH25V2 NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Touch screen Capacitive Screen protection against harmful interference in a residential Camera 5M AF /(0.3M FF optional) radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful Wireless data 2G:B2/B3/B5/B8 3G:WCDMA(B1/B2/B4/B5) 4G:B2/B3/B4/B7/B17/B28 Wi-Fi Build-in Wi-Fi 802.11a/b/g/n(2.4G/5G) installation. Bluetooth Support Bluetooth 4.0 Keys Power key, volume key equipment off and on, the user is encouraged to try to correct Interfaces USB Type C,Nano SIM the interference by one or more of the following measures: Printer type Thermal Printer Printing paper specifications Width 58mm, maximum diameter 50mm distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not accessories that do not satisfy these requirements may not Circuit board comply with FCC RF exposure requirements, and should be Shell Battery 7.6V/2580mAh Outline dimensions L 219.1mm ×W 80mm ×H 17.8mm television reception, which can be determined by turning the ---Reorient or relocate the receiving antenna. Technical features and characteristic ---Connect the equipment into an outlet on a circuit different Operation Frequency Transmitted GSM 850 824-849 MHz(Tx),869-894 MHz(Rx) 32 dBm GSM 1900 1850-1910 MHz(Tx),1930-1990 MHz(Rx) 30 dBm Body-worn Operation WCDMA BAND II 1850-1910 MHz(Tx),1930-1990 MHz(Rx) 23 dBm This device was tested for typical body-worn operations. To WCDMA BAND IV 1710 -1755 MHz(Tx),2110 - 2155MHz(Rx) 23 dBm comply With RF exposure requirements, a minimum separation WCDMA BAND V 824-849 MHz(Tx),869-894 MHz(Rx) 23.5 dBm distance of 1.0cm must be maintained between the user’s body LTE BAND 2 1850-1910 MHz(Tx),1930-1990 MHz(Rx) 22.5 dBm LTE BAND 4 1710-1755 MHz(Tx),2110-2155 MHz(Rx) 22.5 dBm LTE BAND 7 2500-2570 MHz(Tx),2620-2690 MHz(Rx) 22.5 dBm LTE BAND 17 704-716 MHz(Tx),734-746 MHz(Rx) 23 dBm 2.4G Wi-Fi 2412-2462 MHz 15 dBm may not comply with RF exposure requirements and should be Bluetooth 2402-2480 MHz 6 dBm avoided. BLE 2402-2480 MHz 6 dBm Specific Absorption Rate (SAR) information: 5G Wi-Fi 5150-5250 MHz 17 dBm This wireless phone meets the government's requirements for 5G Wi-Fi 5725-5850 MHz 16.5 dBm and the handset, including the antenna. Third-party belt-clips, holsters, and similar including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements User Guide T5930 through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. Device types: T5930 has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification when properly worn on the body is List of packaged items Terminal device × 1 User's Guide × 1 Charger & Adapter × 1 USB Cable × 1 1.856W/kg(10gSAR, test distance:10mm,limit 4W/kg)and 1.276W/kg (1gSAR, test distance:10mm,limit 1.6W/kg). This device was tested for body-worn operations with the back of (PBDE) Manufacture Shanghai Sunmi Technology Co.,Ltd. Room 505 No.388 Song Hu Road Shanghai, China that were developed by independent scientific organizations USA (FCC) is 1.6W/kg averaged over one gram of tissue. (PBB) This product can be used across EU member states. The full text of the EU declaration DOC is available at the following internet address:www.sunmi.com exposure to radio waves. The guidelines are based on standards FCC RF Exposure Information and Statement. The SAR limit of (Cr(VII) For products that have reached or passed the service years for environmental protection, they should be recycled according to Measures for Control and Management of Electronic Information Products and should not be thrown away at will. If this equipment does cause harmful interference to radio or help. (Cd) :It indicates that the content of toxic and harmful substances is higher than the limit specified in SJ/T11363-2006 in at least one homogeneous material of this part; however, the the reason why the toxic substance of that part exceeds the limit is that there is no applicable material to replace it currently. guarantee that interference will not occur in a particular ---Consult the dealer or an experienced radio/TV technician for (Hg) :It indicates that the content of toxic and harmful substances in all homogeneous materials of this part is below the limit specified in SJ/T11363-2006. interference to radio communications. However, there is no from that to which the receiver is connected. (Pb) avoided. installation. This equipment generates uses and can radiate receiver. Toxic and harmful substances and elements Name of parts contain metallic components in its assembly. The use of the FCC Rules. These limits are designed to provide reasonable ---Increase the separation between the equipment and Name and content of toxic and harmful substances contained in this product are shown in the following table accessories that maintain a 10mm and 5mm separation with the limits for a Class B digital device, pursuant to Part 15 of 5.45 inch IPS, resolution 1440×720 OUTPUT:DC5V/2A INPUT:AC100~240V/0.3A 50/60Hz compliance with FCC RF exposure requirements, use NOTE: This equipment has been tested and found to comply Display Adapter the handset kept 10mm and 5mm from the body. To maintain 请自行添加一维码 内容为说明书料号 Product Description Opening handle Printer Camera Speaker Extended interface Power key Type-C USB SIM Card Slot Nano SIM Volume key Battery cover Printing instructions This device supports 58mm thermal paper with the specifications of 57±0.5mm*Ø50mm · Please open the paper container with the uncovering handle (as shown in Fig.1). Please do not force open the paper container to avoid print head gear wear; · Feed the paper correctly into the paper container in the direction as shown, and pull some paper outside the cutter (as shown in Fig.2); · Close the cover of the paper container to finish printing paper feeding(as shown in Fig.3). Note: If the printed paper is blank, please check whether the paper roll has been installed in the correct direction. Type-C USB Charger & Adapter Power key Short press: wake up the screen, lock the screen. Long press: long press for 2-3 seconds in power off mode to switch on the device. Long press for 2-3 seconds in normal operation mode to select power off or reboot. Long press for 11 seconds when system is frozenfor automatic reboot. Volume key Volume adjustment. Printer For printing sales slips in power on mode. Type-C USB For device recharging and developer debugging. Camera For payment scanning and 1D/2D code quick scanning. SIM Card Slot Note: To prevent system errors, please make sure the device is turned off when you insert or remove the SIM card. Power Outlet Instructions for recharging and battery This device supports charging only by USB cable · Connect the 5V adapter to the power supply socket; · Connect the USB cable to the USB interface of the device for recharging; · The screen will display the recharging icon during the recharging process; · If the recharging icon does not appear, please check whether the USB interface is well connected. Instructions/Notes for battery · This device adopts 7.6V/2580mAh lithium battery; please do not disassemble the battery. · In order to protect the battery life, we recommend that yourecharge the device whenever possible, and please do not allow the battery to fully drain before recharging. Extremely easy settings Precautions Only a few steps to activate an intelligent business device ①Set 2G/3G/4G: when power off, insert the 2G/3G/4G card and then power on. (Refer to the Technical Specifications for the support of cards) ② Long press the Power Key for 2~3s to activate the backlight of screen,and then operate following the prompts after entering the startup/booting screen for the first time. 2 modes for accessing the Internet are available. ③ Set WiFi · Click "Set" button, activate "WLAN" to enter the WLAN searching screen, and wait it to list all useable WLAN hot spots; · Click the WLAN to be connected, and enter the access password in case of an encrypted network. Safety Warning · Connect the AC plug to the AC socket corresponding to the marked input of the power adapter; · Do not use in the presence of any potentially explosive gas; · To avoid injury, unauthorized persons shall not open the power adapter; · This is a Class A product. This product may cause radio interference in living environments. In that case, the user may be required to take adequate measures against interference. · Battery replacement: 1. Explosion danger may arise if replacing with the wrong battery! 2. The replaced battery shall be disposed of by maintenance personnel,and please do not throw it into fire! Download/use Apps After connected to the Internet, open the App Market, find, download and install the Apps. Significant Safety Instructions · This terminal is a handheld device, and the user shall protect the password from being peered at by others while entering the password; · Do not install or use the device during lightning storms to avoid the potential risks of lightning shock; · Please turn off the power immediately if you notice abnormal odor, heat or smoke; · The paper cutter is sharp, please do not touch! FAQ Booting failure (e.g. low battery) · Plug the USB cable and charge for 3min; · Check if the screen displays the normal charging status. System crash · Long press the Power Key for 11s to reboot. Read the installed Help App for more information Suggestions · Do not use the terminal near water or moisture to prevent liquid from falling into the terminal; · Do not use the terminal in extremely cold or hot environments, such as near flames or lit cigarettes; · Do not drop, throw or bend the device; · Use the terminal in a clean and dust-free environment if possible to prevent small items from falling into the terminal; · Please do not use the terminal near medical equipment without permission. Statements The Company does not assume responsibilities for the following actions: · Damages caused by use and maintenance without complying with the conditions specified in this guide; · The Company will not assume any responsibilities for the damages or problemscaused by optional items or consumables (rather than the initial products or approvedproducts of the Company). The customer is not entitled to change or modify the product without our consent. · The product’s operating system supports official systemupdates, but if you change the operating system into a third party ROM system or alter the system files by system cracking, it may cause system instability and security risks and threats. Disclaimer As a result of product upgrading, some details in this document may not match the product, and the actual product shall govern. The Company reserves the right of interpretation of this document. The Company also reserves the right toalter this specification without prior notice.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 5.6-c137 79.159768, 2016/08/11-13:24:42 Creator Tool : Adobe Illustrator CC 2017 (Macintosh) Create Date : 2019:01:29 11:51:49+08:00 Modify Date : 2019:01:29 11:51:49+08:00 Metadata Date : 2019:01:29 11:51:49+08:00 Thumbnail Width : 184 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 17180 bytes, use -b option to extract) N Pages : 1 Has Visible Transparency : True Has Visible Overprint : False Max Page Size W : 400.000004 Max Page Size H : 214.999993 Max Page Size Unit : Millimeters Font Name : PingFang-SC-Regular, PingFangSC-Regular, CenturyGothic-Bold, CenturyGothic Font Family : 苹方, 苹方-简, Century Gothic, Century Gothic Font Face : 常规, 常规体, Bold, Regular Font Type : TrueType, Open Type, Open Type, Open Type Font Version : 10.11d9e1, 13.0d1e3, 13.0d1e4, 13.0d1e4 Font Composite : False, False, False, False Font File Name : PingFang Regular.ttf, PingFang.ttc, CenturyGothic.ttc, CenturyGothic.ttc Plate Names : Cyan, Magenta, Yellow, Black, PANTONE Orange 021 C, PANTONE 165 C Swatch Group Name : 默认色板组 Swatch Group Type : 0 Swatch Colorant Swatch Name : AutoCAD Color, PANTONE 165 C, PANTONE Black 6 C, AutoCAD Color 8, AutoCAD Color 5, AutoCAD Color 2, AutoCAD Color 3, AutoCAD Color 4, PANTONE Orange 021 C Swatch Colorant Type : PROCESS, SPOT, SPOT, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, SPOT Swatch Colorant Tint : 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000 Swatch Colorant Mode : CMYK, Lab, Lab, CMYK, CMYK, CMYK, CMYK, CMYK, Lab Swatch Colorant Cyan : 92.941201, 54.924798, 92.971700, 2.841200, 54.924798, 61.327499 Swatch Colorant Magenta : 87.923998, 0.000000, 87.972802, 32.376599, 0.000000, 0.000000 Swatch Colorant Yellow : 89.019603, 17.715700, 89.019603, 89.864999, 17.715700, 100.000000 Swatch Colorant Black : 79.998499, 0.000000, 79.998499, 0.000000, 0.000000, 0.000000 Swatch Colorant L : 64.705902, 7.843140, 60.784302 Swatch Colorant A : 59, -2, 66 Swatch Colorant B : 68, -7, 85 Format : application/pdf Title : 认证_V2 英文美版用户指南_20190129 Rendition Class : proof:pdf Document ID : xmp.did:06a0d217-ad59-4e92-afea-bd4f7bb2e772 Instance ID : uuid:a5663e4b-e280-124b-aa59-7e95c4a93b39 Original Document ID : uuid:dfebd2e3-de19-48fc-9fc3-26c53bbd00c2 Derived From Instance ID : xmp.iid:1a00ef60-ecfc-4f0a-8d73-b7936a0b0f79 Derived From Document ID : xmp.did:1a00ef60-ecfc-4f0a-8d73-b7936a0b0f79 Derived From Original Document ID: uuid:dfebd2e3-de19-48fc-9fc3-26c53bbd00c2 Derived From Rendition Class : proof:pdf History Action : saved, saved History Instance ID : xmp.iid:ef391e11-f7f2-4a40-964f-6dec6791ec20, xmp.iid:06a0d217-ad59-4e92-afea-bd4f7bb2e772 History When : 2017:09:20 16:56:11+08:00, 2019:01:29 11:51:48+08:00 History Software Agent : Adobe Illustrator CC 2017 (Macintosh), Adobe Illustrator CC 2017 (Macintosh) History Changed : /, / Producer : Adobe PDF library 15.00 Page Count : 2 Creator : Adobe Illustrator(R) 17.0 AI Creator Version : 21.0.0 For : �տ˱�, Bounding Box : -335 3420 811 5019 AI Build Number : 223 AI Color Usage : Color AI Ruler Units : Millimeters AI Color Model : CMYK AI Target Resolution : 800 AI Num Layers : 3 Container Version : 11 Creator Version : 21EXIF Metadata provided by EXIF.tools