Super Nova Co NVX1201H 2-Way Security Transceiver User Manual RW6400T2WAY CSP E

Super Nova Co Ltd 2-Way Security Transceiver RW6400T2WAY CSP E

User Manual

RW6400T 2 Way Transmitter (TR5) Operation manual LCD Panel Function Shown: To Anti-Car Jacking: Main Unit Parking Flash 2 times and LED flash Quickly (no picture shown). Button 5: a. Show the company Logo or the last message. b. Keep press 3” to Change Channel I or II ( 1st Car or 2nd Car). c. Press 5 times to Voice or null voice prompt for button operation. Button 5 START Basic function of button : Button 1 : a. Arm. b. Keep press 3 second to Panic. Button 2 : Disarm (and it will open the central look on driver side.) than press one more time in 5”, it will open the central lock on other doors. Button 3 : a. Remote 1st aux. output (Trunk pop). b. Keep press 2-3” to remote 2nd aux. output. Button 4 : Remote start --- press again to off. Button 1+2 : a. When arming --- keep press 3” to all (shock & option) sensor bypass. b. When disarm --- press 3” to valet mode, when keep 6” to valet park mode. Button 1+3 : To anti-car jacking. Button 2+4 : Chirp defeat arm / disarm TR5 Layout Description LCD Panel Button 2 Button 4 (AUX) Button 1 Button 3 Arm (1st Car) Disarm (2nd Car) Chirp defeat disarm Chirp defeat arm Panic Door open 1st aux. output Trunk POP (or Hood Open) Data translate..! Low battery Remote Start (Picture move) Valet Park (flash 20 ti )Valet Warn away IGN VLT VLT Transmitter learning Shock Sensor (hammer move) L Central Unlock Central Lock Logo CSP USA P
6400 Updated Program Option Chart PROGRAM: RW6400C0.HEX Option Option Description Fac. Pre-set Tx Button Tx Button Tx Button Tx Button 1 Tach Learning Learning 2 Auto Lock With Ignition ON OFF ON 3 Aggressive Arm Mode OFF ON OFF 4 Active Re-Arm Mode OFF ON OFF 5 Passive Lock OFF ON OFF 6 Parking Light Illumination on Disarm ON OFF ON 7 Valet Park Protection Mode or Trunk Mode Trunk Valet Park Trunk 8 Passive Car-Jacking Mode Remote Car-Jacking Passive Car-Jacking Remote Car-Jacking 9 Siren Confirmation for Remote Start ON OFF ON 10 Aux Disarm ON OFF ON 11 5/60 Second Warning Chirps (Normal Car/Dome Light Delay Car) 60 sec. 5 sec. 60 sec. 12 Door Lock Pulse Time 0.75 sec. 3.0 sec. 0.75 sec. 13 Double Unlock Pulse 1 Pules 2 Pules 1 Pules 14 Remote Start Run Time 24 min. 12 min. 24 min. 36 min. 48 min 15 Option Reset Reset START (RS Serial )
Voltage Detect setting use two jumpers (1=short, 0=open) P1(0), P2(0) = 91% P1(1), P2(0) = 92% P1(1), P2(1) = 93% *Default P1 P2 How to Update Program Option Function: 1) Turn ignition to the “ON” position; Hood “ON” 2) Press valet override switch 5 times 3) Press valet override switch the number of times corresponding to the “feature setting chart”. 4) Press the “Lock” button to change to feature setting Press the “Unlock” button to return to default setting N / A P3
RW6400 WIRING DIAGRAM GREEN TRIGER(-) TO START/STOP ENGIN BROWN (+)SIREN BROWN/WHITE (-)HORN BLACK/WHITE (-)500mA DOME LIGHT GREEN/RED (-)AUX 1 BLUE/BLACK (-)AUX 2 BLUE/WHITE UNLOCK 2(-) ORANGE (-)START KILL/ANTI GRIND ORANGE/BLACK OEM DISARM OVERRIDE SWITCH SHOCK SENSOR LED NPC3 Module (Optional) PINK BLACK For GLOW PLUG(-) INPUT RED +12VDC PURPLE DOOR INPUT(+) GREEN DOOR INPUT(-) BLUE HOOD INPUT (-) PINK CAR JACKING or GLOW PLUG(+) INPUT (Diesel engine only) WHITE PEDAL BRAKE(+) RESET INPUT BROWN (+) STARTER GRAY (+) ACCESSORY RED (+) 12VDC RED (+) 12VDC PINK (+) IGNITION (IN/OUT) WHITE (+) PARKING LIGHT(12 Amp) (F2WA-1) (NPC3) 30Amp FUSE 30Amp FUSE WHITE/RED TO TACHOMETER BLACK GROUND YELLOW/WHITE (-) ACC 2 YELLOW (-)IGNITION 2 GREEN LOCK(-) RED (+)12 VDC BLUE UNLOCK(-) ATT: Do not connect White/ Red wire to tachometer, if decide to use TACH less engine monitor. (smart sensor) * : Whenever connect White/ Red wire to tachometer, This system automatically turn to “TACH-Learning” mode. IGNITION COIL ＋ － (SKIN OFF TACHOMETER WIRE AND CONNECT TOGETHER) This system has TACH less engine monitor feature, even without connect any detection wire, still will have smart cranking ability, cranking time auto-adjust depends on voltage changing .
How to use the “Code Learning” for RW6400 Please following step by step 1. Turn ignition (on) and turn hood (on) (waiting for 5 second for signal feed back) 2. Press the override switch 4 times (then the parking light will flashed 4 times, led steady light on) 3. Presses the button ➀ (lock) and button ➁ (unlock) at same time, for new transmitter for learning, siren chirps 2 times than waiting the LCD shows picture of “attain” it means this transmitter is completed for code learning. 4. Presses the button ➀ (lock) and button ➁ (unlock) at same time, for 2nd new transmitter for learning siren chirp 3 times than waiting LCD shows picture of “attain” it means this transmitter is completed for code learning. 5. A main unit can at most accept for 4 transmitters code learning. How to update program option function of RW6400 Please following step by step 1. Turn ignition (on) and turn hood (on) (waiting for 5 second for signal feed back) 2. Press the override switch 5 times (then the parking light will flash 5 times, led steady light on) For example, program the option function #12 ”door luck pulse time” when finished above 2 steps, then keep following the below steps: ★ Press override switch 12 times (means program the option function #12) each time press the override switch, the Parking Light will flash once, for this #12 programming totally will be flashed 12 times by 12 times pressing the override switch. When saw the 12th flash means the system programming mode is on the #12 option function programming status. ★ after above, press the remote “lock” button, by the mean time, the parking light will flash once for signal, that means the programming procedure for set-up the option function #12 is finished. Please reference the ”update program option chart” the system was set-up the central door lock/unlock as “3 seconds pulse”, that means every lock/unlock pulse is 3 seconds, this is for match the original setting for central door lock/unlock on the MERCEDES, BENZ.
Notice: 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu