Super Nova Co NVX1201H 2-Way Security Transceiver User Manual RW6400T2WAY CSP E

Download:
Mirror Download [FCC.gov]
Document ID	262611
Application ID	LMDza4YiCjsE2/788W9/vA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	23.63kB (295315 bits)
Date Submitted	2002-08-09 00:00:00
Date Available	2002-08-09 00:00:00
Creation Date	2002-08-02 03:40:36
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2002-08-02 11:44:59
Document Title	Microsoft Word - RW6400T2WAY-CSP_E.doc
Document Creator	ADOBEPS4.DRV Version 4.50
Document Author:	Jill

RW6400T 2 Way Transmitter (TR5) Operation manual
Basic function of button :
TR5 Layout Description
Button 1 : a. Arm.
b. Keep press 3 second to Panic.
Button 2 : Disarm (and it will open the central
look on driver side.) than press one
more time in 5”, it will open the central
lock on other doors.
Button 3 : a. Remote 1st aux. output (Trunk pop).
b. Keep press 2-3” to remote 2nd aux.
output.
LCD
Panel
(AUX)
Button 5
Button 4 : Remote start --- press again to off.
Button 1
Button 2
Button 3
Button 4
START
Button 1+2 : a. When arming --- keep press 3” to
all (shock & option) sensor
bypass.
b. When disarm --- press 3” to valet
mode, when keep 6” to valet
park
mode.
Button 1+3 : To anti-car jacking.
Button 2+4 : Chirp defeat arm / disarm
LCD Panel Function Shown:
Arm
(1st Car)
Disarm
(2nd Car)
IGN
1st aux. output Remote Start
Trunk POP
(Picture move)
(or Hood Open)
Chirp defeat arm
Panic
Chirp defeat disarm
VLT
Valet
VLT
Door open
Valet Park
(flash 20
ti
Central
Lock
CSP
Low battery
Central
Unlock
USA
Data translate..!
Transmitter
learning
Shock Sensor
(hammer move)
Warn away
Logo
To Anti-Car Jacking: Main Unit Parking Flash 2 times and LED flash Quickly (no picture shown).
Button 5: a. Show the company Logo or the last message.
b. Keep press 3” to Change Channel I or II ( 1st Car or 2nd Car).
c. Press 5 times to Voice or null voice prompt for button operation.
6400 Updated Program Option Chart
PROGRAM: RW6400C0.HEX
Option Option Description
Fac. Pre-set Tx Button
Tx Button
Tx Button
(RS Serial )
Tx Button
START
Tach Learning
Learning
Auto Lock With Ignition ON
OFF
ON
Aggressive Arm Mode
OFF
ON
OFF
Active Re-Arm Mode
OFF
ON
OFF
Passive Lock
OFF
ON
OFF
Parking Light Illumination ON
on Disarm
OFF
ON
Valet Park Protection
Mode or Trunk Mode
Valet Park
Trunk
Passive Car-Jacking Mode Remote
Passive
Remote
Car-Jacking Car-Jacking Car-Jacking
Siren Confirmation for
Remote Start
ON
OFF
ON
10
Aux Disarm
ON
OFF
ON
11
5/60 Second Warning
60 sec.
Chirps (Normal Car/Dome
Light Delay Car)
5 sec.
60 sec.
12
Door Lock Pulse Time
0.75 sec.
3.0 sec.
0.75 sec.
13
Double Unlock Pulse
1 Pules
2 Pules
1 Pules
14
Remote Start Run Time
24 min.
12 min.
24 min.
15
Option Reset
Trunk
Reset
36 min.
48 min
P1
P2
P3
Voltage Detect setting use two jumpers (1=short, 0=open)
P1(0), P2(0) = 91%
P1(1), P2(0) = 92%
P1(1), P2(1) = 93%
*Default
N/A
How to Update Program Option Function:
1) Turn ignition to the “ON” position; Hood “ON”
2) Press valet override switch 5 times
3) Press valet override switch the number of times corresponding to the
“feature setting chart”.
4) Press the “Lock” button to change to feature setting
Press the “Unlock” button to return to default setting
RW6400 WIRING DIAGRAM
(F2WA-1)
(NPC3)
SHOCK
SENSOR
OVERRIDE
SWITCH
LED
GREEN
RED
BLUE
PURPLE
GREEN
BLUE
PINK
WHITE
LOCK(-)
(+)12 VDC
UNLOCK(-)
DOOR INPUT(+)
DOOR INPUT(-)
HOOD INPUT (-)
CAR JACKING or GLOW PLUG(+) INPUT (Diesel engine only)
PEDAL BRAKE(+) RESET INPUT
(Optional)
NPC3
Module
PINK
BLACK
RED
GREEN
BROWN
BROWN/WHITE
BLACK/WHITE
GREEN/RED
BLUE/BLACK
BLUE/WHITE
ORANGE
ORANGE/BLACK
For GLOW PLUG(-) INPUT
+12VDC
TRIGER(-) TO START/STOP ENGIN
(+)SIREN
(-)HORN
(-)500mA DOME LIGHT
(-)AUX 1
(-)AUX 2
UNLOCK 2(-)
(-)START KILL/ANTI GRIND
OEM DISARM
(SKIN OFF TACHOMETER WIRE AND CONNECT TOGETHER)
WHITE/RED
BLACK
YELLOW/WHITE
YELLOW
30Amp FUSE
30Amp FUSE
BROWN
GRAY
RED
RED
PINK
WHITE
TO TACHOMETER
GROUND
(-) ACC 2
(-)IGNITION 2
(+) STARTER
(+) ACCESSORY
(+) 12VDC
(+) 12VDC
(+) IGNITION (IN/OUT)
(+) PARKING LIGHT(12 Amp)
ATT: Do not connect White/ Red wire to tachometer,
if decide to use TACH less engine monitor.
(smart sensor)
* : Whenever connect White/ Red wire to
tachometer, This system automatically turn to
“TACH-Learning” mode.
＋
－
IGNITION COIL
This system has TACH less engine monitor feature, even without connect any detection wire, still will
have smart cranking ability, cranking time auto-adjust depends on voltage changing .
How to use the “Code Learning” for RW6400
Please following step by step
1. Turn ignition (on) and turn hood (on) (waiting for 5 second for signal feed back)
2. Press the override switch 4 times (then the parking light will flashed 4 times, led steady light
on)
3. Presses the button ➀ (lock) and button ➁ (unlock) at same time, for new transmitter for
learning, siren chirps 2 times than waiting the LCD shows picture of “attain” it means this
transmitter is completed for code learning.
4. Presses the button ➀ (lock) and button ➁ (unlock) at same time, for 2nd new transmitter for
learning siren chirp 3 times than waiting LCD shows picture of “attain” it means this
transmitter is completed for code learning.
5. A main unit can at most accept for 4 transmitters code learning.
How to update program option function of RW6400
Please following step by step
1. Turn ignition (on) and turn hood (on) (waiting for 5 second for signal feed back)
2. Press the override switch 5 times (then the parking light will flash 5 times, led steady light on)
For example, program the option function #12 ”door luck pulse time” when finished above 2 steps,
then keep following the below steps:
★ Press override switch 12 times (means program the option function #12) each time press the
override switch, the Parking Light will flash once, for this #12 programming totally will be
flashed 12 times by 12 times pressing the override switch. When saw the 12th flash means the
system programming mode is on the #12 option function programming status.
★ after above, press the remote “lock” button, by the mean time, the parking light will flash
once for signal, that means the programming procedure for set-up the option function #12 is
finished. Please reference the ”update program option chart” the system was set-up the
central door lock/unlock as “3 seconds pulse”, that means every lock/unlock pulse is 3
seconds, this is for match the original setting for central door lock/unlock on the MERCEDES,
BENZ.
Notice: 1. The changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
2. This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2002:08:02 03:40:36Z
Modify Date                     : 2002:08:02 11:44:59+08:00
Page Count                      : 6
Creation Date                   : 2002:08:02 03:40:36Z
Mod Date                        : 2002:08:02 11:44:59+08:00
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : Jill
Metadata Date                   : 2002:08:02 11:44:59+08:00
Creator                         : Jill
Title                           : Microsoft Word - RW6400T2WAY-CSP_E.doc

EXIF Metadata provided by EXIF.tools