Super Nova Co NVX1201H 2-Way Security Transceiver User Manual RW6400T2WAY CSP E
Super Nova Co Ltd 2-Way Security Transceiver RW6400T2WAY CSP E
User Manual
RW6400T 2 Way Transmitter (TR5) Operation manual
LCD Panel Function Shown:
To Anti-Car Jacking: Main Unit Parking Flash 2 times and LED flash Quickly (no picture shown).
Button 5: a. Show the company Logo or the last message.
b. Keep press 3” to Change Channel I or II ( 1st Car or 2nd Car).
c. Press 5 times to Voice or null voice prompt for button operation.
Button 5
START
Basic function of button :
Button 1 : a. Arm.
b. Keep press 3 second to Panic.
Button 2 : Disarm (and it will open the central
look on driver side.) than press one
more time in 5”, it will open the central
lock on other doors.
Button 3 : a. Remote 1st aux. output (Trunk pop).
b. Keep press 2-3” to remote 2nd aux.
output.
Button 4 : Remote start --- press again to off.
Button 1+2 : a. When arming --- keep press 3” to
all (shock & option) sensor
bypass.
b. When disarm --- press 3” to valet
mode, when keep 6” to valet
park
mode.
Button 1+3 : To anti-car jacking.
Button 2+4 : Chirp defeat arm / disarm
TR5 La
y
out Descri
p
tion
LCD
Panel
Button 2
Button 4
(
AUX
)
Button 1
Button 3
Arm
(1st Car)
Disarm
(2nd Car)
Chirp defeat disarm Chirp defeat arm
Panic
Door open
1s
t
aux. output
Trunk POP
(or Hood Open)
Data translate..! Low battery
Remote Start
(Picture move)
Valet Park
(flash 20
ti )
Valet
Warn away
IGN VLT VLT
Transmitter
learning
Shock Sensor
(hammer move)
L
Central
Unlock
Central
Lock
Logo
CS
P
USA
P
6400 Updated Program Option Chart
PROGRAM: RW6400C0.HEX
Option Option Description Fac. Pre-set Tx Button
Tx Button Tx Button Tx Button
1 Tach Learning Learning
2 Auto Lock With Ignition ON OFF ON
3 Aggressive Arm Mode OFF ON OFF
4 Active Re-Arm Mode OFF ON OFF
5 Passive Lock OFF ON OFF
6 Parking Light Illumination
on Disarm
ON OFF ON
7 Valet Park Protection
Mode or Trunk Mode
Trunk Valet Park Trunk
8 Passive Car-Jacking Mode Remote
Car-Jacking
Passive
Car-Jacking
Remote
Car-Jacking
9 Siren Confirmation for
Remote Start
ON OFF ON
10 Aux Disarm ON OFF ON
11 5/60 Second Warning
Chirps (Normal Car/Dome
Light Delay Car)
60 sec. 5 sec. 60 sec.
12 Door Lock Pulse Time 0.75 sec. 3.0 sec. 0.75 sec.
13 Double Unlock Pulse 1 Pules 2 Pules 1 Pules
14 Remote Start Run Time 24 min. 12 min. 24 min. 36 min. 48 min
15 Option Reset Reset
START
(RS Serial )
Voltage Detect setting use two jumpers (1=short, 0=open)
P1(0), P2(0) = 91%
P1(1), P2(0) = 92%
P1(1), P2(1) = 93% *Default
P1
P2
How to Update Program Option Function:
1) Turn ignition to the “ON” position; Hood “ON”
2) Press valet override switch 5 times
3) Press valet override switch the number of times corresponding to the
“feature setting chart”.
4) Press the “Lock” button to change to feature setting
Press the “Unlock” button to return to default setting
N / A
P3
RW6400 WIRING DIAGRAM
GREEN TRIGER(-) TO START/STOP ENGIN
BROWN (+)SIREN
BROWN/WHITE (-)HORN
BLACK/WHITE (-)500mA DOME LIGHT
GREEN/RED (-)AUX 1
BLUE/BLACK (-)AUX 2
BLUE/WHITE UNLOCK 2(-)
ORANGE (-)START KILL/ANTI GRIND
ORANGE/BLACK OEM DISARM
OVERRIDE
SWITCH
SHOCK
SENSOR
LED
NPC3
Module
(Optional)
PINK
BLACK For GLOW PLUG(-) INPUT
RED +12VDC
PURPLE DOOR INPUT(+)
GREEN DOOR INPUT(-)
BLUE HOOD INPUT (-)
PINK CAR JACKING or GLOW PLUG(+) INPUT (Diesel engine only)
WHITE PEDAL BRAKE(+) RESET INPUT
BROWN (+) STARTER
GRAY (+) ACCESSORY
RED (+) 12VDC
RED (+) 12VDC
PINK (+) IGNITION (IN/OUT)
WHITE (+) PARKING LIGHT(12 Amp)
(F2WA-1)
(NPC3)
30Am
p
FUSE
30Amp FUSE
WHITE/RED TO TACHOMETER
BLACK GROUND
YELLOW/WHITE (-) ACC 2
YELLOW (-)IGNITION 2
GREEN LOCK(-)
RED (+)12 VDC
BLUE UNLOCK(-)
ATT: Do not connect White/ Red wire to tachometer,
if decide to use TACH less engine monitor.
(smart sensor)
* : Whenever connect White/ Red wire to
tachometer, This system automatically turn to
“TACH-Learning” mode. IGNITION COIL
＋ －
(SKIN OFF TACHOMETER WIRE AND CONNECT TOGETHER)
This system has TACH less engine monitor feature, even without connect any detection wire, still will
have smart cranking ability, cranking time auto-adjust depends on voltage changing .
How to use the “Code Learning” for RW6400
Please following step by step
1. Turn ignition (on) and turn hood (on) (waiting for 5 second for signal feed back)
2. Press the override switch 4 times (then the parking light will flashed 4 times, led steady light
on)
3. Presses the button ➀ (lock) and button ➁ (unlock) at same time, for new transmitter for
learning, siren chirps 2 times than waiting the LCD shows picture of “attain” it means this
transmitter is completed for code learning.
4. Presses the button ➀ (lock) and button ➁ (unlock) at same time, for 2nd new transmitter for
learning siren chirp 3 times than waiting LCD shows picture of “attain” it means this
transmitter is completed for code learning.
5. A main unit can at most accept for 4 transmitters code learning.
How to update program option function of RW6400
Please following step by step
1. Turn ignition (on) and turn hood (on) (waiting for 5 second for signal feed back)
2. Press the override switch 5 times (then the parking light will flash 5 times, led steady light on)
For example, program the option function #12 ”door luck pulse time” when finished above 2 steps,
then keep following the below steps:
★ Press override switch 12 times (means program the option function #12) each time press the
override switch, the Parking Light will flash once, for this #12 programming totally will be
flashed 12 times by 12 times pressing the override switch. When saw the 12th flash means the
system programming mode is on the #12 option function programming status.
★ after above, press the remote “lock” button, by the mean time, the parking light will flash
once for signal, that means the programming procedure for set-up the option function #12 is
finished. Please reference the ”update program option chart” the system was set-up the
central door lock/unlock as “3 seconds pulse”, that means every lock/unlock pulse is 3
seconds, this is for match the original setting for central door lock/unlock on the MERCEDES,
BENZ.
Notice: 1. The changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
2. This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.