Symbol Technologies P470 P 370 / 470 Scanner User Manual manual ID label location on page 28

Symbol Technologies Inc P 370 / 470 Scanner manual ID label location on page 28

manual & ID label/location on page 28

PreliminaryP 370/470 Radio Scanner
PreliminaryP 370/470 Scanner 1997-1999 SYMBOL TECHNOLOGIES, INC. All rights reserved.Symbol reserves the right to make changes to any product to improve reliability, function, or design.Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Symbol products might be used. An implied license only exists for equipment, circuits, and subsystems contained in Symbol products.Symbol and the Symbol logo are registered trademarks of Symbol Technologies, Inc. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.Symbol Technologies, Inc.One Symbol PlazaHoltsville, N.Y. 11742-1300http://www.symbol.comPatentsThis product is covered by one or more of the following U.S. and foreign Patents: U.S. Patent No.4,360,798; 4,369,361; 4,387,297; 4,460,120; 4,496,831; 4,593,186; 4,603,262; 4,607,156; 4,652,750; 4,673,805; 4,736,095; 4,758,717; 4,816,660; 4,845,350; 4,896,026; 4,897,532; 4,923,281; 4,933,538; 4,992,717; 5,015,833; 5,017,765; 5,021,641; 5,029,183; 5,047,617; 5,103,461; 5,113,445; 5,130,520 5,140,144; 5,142,550; 5,149,950; 5,157,687; 5,168,148; 5,168,149; 5,180,904; 5,229,591; 5,230,088; 5,235,167; 5,243,655; 5,247,162; 5,250,791; 5,250,792; 5,262,627; 5,262,628; 5,266,787; 5,278,398; 5,280,162; 5,280,163; 5,280,164; 5,280,498; 5,304,786; 5,304,788; 5,306,900; 5,321,246; 5,324,924; 5,337,361; 5,367,151; 5,373,148; 5,378,882; 5,396,053; 5,396,055; 5,399,846; 5,408,081; 5,410,139; 5,410,140; 5,412,198; 5,418,812; 5,420,411; 5,436,440; 5,444,231; 5,449,891; 5,449,893; 5,468,949; 5,471,042; 5,478,998; 5,479,000; 5,479,002; 5,479,441; 5,504,322; 5,519,577; 5,528,621; 5,532,469; 5,543,610; 5,545,889; 5,552,592; 5,578,810; 5,581,070; 5,589,679; 5,589,680; 5,608,202; 5,612,531; 5,619,028; 5,664,229; 5,668,803; 5,675,139; 5,693,929; 5,698,835; 5,705,800; 5,714,746; 5,723,851; 5,734,152; 5,734,153; 5,745,794; 5,754,587; 5,762,516; 5,763,863; 5,767,500; 5,789,728; 5,808,287; 5,811,785; 5,811,787; 5,815,811; 5,821,519; 5,821,520; 5,823,812; 5,828,050; 5,850,078; 5,861,615; 5,874,720; 5,875,415; D305,885; D341,584; D344,501; D359,483; D362,453; D363,700; D363,918; D370,478; D383,124; D391,250; D405,077; D406,581.Invention No. 55,358; 62,539; 69,060; 69,187 (Taiwan); No. 1,601,796; 1,907,875; 1,955,269 (Japan).European Patent 367,299; 414,281; 367,300; 367,298; UK 2,072,832; France 81/03938; Italy 1,138,713.rev. 4/99
Preliminary1Quick ReferenceIntroductionThe Phaser P 370/470 Radio Frequency (RF) scanner brings new flexibility and economy to data capture and data management in retail operations. The RF scanner has an integrated keypad and display, communicates with a base station and is battery-powered. This provides advanced point-of-sale scanning and also allows the scanner to be used for other in-store tasks such as delivery, inventory, pricing, and even gift registry. There are two versions available:• P 470: the RF retail version• P 370: the RF industrial versionThis Quick Reference Guide provides basic instruction on the set up and use of the scanner. Unless otherwise noted, the term Phaser refers to both versions of the scanner.Charge the BatteryBefore its first use, the battery must be charged. After the base/charger has been connected, insert the scanner into the base/charger.To charge the scanner, place it front-side down into the base/charger. Make sure that the contacts in the bottom of the scanner match up with the metal contacts.
Preliminary2P 370/470 ScannerA full charge takes up to 4 hours, you may need less time depending upon the remaining charge in the battery. The LED light on the bottom of the cradle becomes solid to alert you when the battery has been recharged.Scanning with the PhaserFor POS operation, the scanner ships with a default application that is ready-to-use right out of the box. Otherwise, consult the Phaser Series Scanner Product Reference Guide (p/n 72-33495-xx) for programming instructions. If you need assistance, contact your local supplier or Symbol Support Center.1. Ensure the battery is charged.2. Make sure the bar code is in the correct scanning range. Aim and press the trigger. When the scanner has read the symbol:- You hear a beep.- The LED above the screen turns green.- The red laser turns off.
Preliminary3Quick ReferenceKeyboard EntryInstead of scanning a bar code, you can enter the bar code’s data using the keypad on the top of the scanner. To enter numeric characters, press the number key on the keypad.To enter alpha characters, press the Mode key once to put the scanner in Alpha Mode. Press the numeric key with the letter you want above it - once for the first letter, quickly twice for the second letter, or quickly three times for the third letter.To return to numeric mode, press the Mode key again.The * key is a special key that can be programmed for custom specific operations. Ask your system administrator for more information.Host CommunicationsWith some terminal types, the Phaser is unable to answer host terminal polls until the appropriate host type is selected. This may result in an error message generated by the host computer. Contact your System Administrator for assistance.
Preliminary4P 370/470 ScannerAiming Hold at an angleDo not hold the scanner directly over the bar code. Laser light reflecting directly back into the scanner from the bar code is known as specular reflection. This strong light can “blind” the scanner and make decoding difficult. The area where specular reflection occurs is known as a “dead zone”.You can tilt the scanner up to 65° forward or back and achieve a successful decode. Simple practice quickly shows what tolerances to work within.65°65°ScanBeam ScanBeamBar Code Bar Code Bar CodeShaded area represents dead zone (±2°)41#6XFFHVVIXO6FDQQLQJ51#3RVVLEOH#6SHFXODU5HIOHFWLRQ61#6XFFHVVIXO6FDQQLQJ
Preliminary5Quick ReferenceScan the entire symbol• The scan beam must cross every bar and space on the symbol (as in the left bar code below).• The larger the symbol, the farther away you should hold the scanner.• Hold the scanner closer for symbols with bars that are close together.Right WrongPair Scanner with Base/ChargerThe wireless “connection” between the scanner and base/charger is the low power radio transmission through RF transceivers in the both the scanner and base/charger. The actual communication consists of bidirectional message packets. However, the scanner and base/charger must be paired for this communication to work between the two devices.To pair the scanner with the base/charger:• Scan the PAIRING bar code below or the one on the base/charger.• Insert the scanner into the base/charger’s cradle. You have 15 seconds to do this, or there will be error beeps (4 beeps = un-successful pairing or base not powered). Note that you cannot PAIRING
Preliminary6P 370/470 Scannerscan data until this linking is complete.• At that time, through the scanner’s contact shoe, there is an exchange of information (addressing, RF channels, etc.) be-tween the scanner and the base/charger’s cradle. This occurs in less than a second.• After the exchange is complete, the scanner and base/charger are paired. Successful pairing is indicated by as warble beep; failure, or unsuccessful link, is indicated by a Lo Lo Lo Lo beep.Set Host TypeEach Interface Cable Assembly defaults to a given host. Below is a list of the assemblies and their corresponding default hosts. If you wish to change the type of host, find and scan the proper bar code on the following pages.Cable Assy. DefaultIK-0100, -0101 IBM 4683/93 Port 5B; 4683/84 Port 17IK-1005, -1006 ICL 9505, 9507, 9518; 9520 OCIAIK-0200 IBM 3683, 3684 Keybd WedgeIK-0300 IBM 3653 Kybd WedgeIK-0400 IBM PC/AT, Telex Memorex Kybd WedgesIK-0401 IBM PS/2 - 30, 50, 55SX, 60, 70, 80IK-0402, -0403 NCR 7052 Wedge; Fujitsu 9000 WedgeIK-0406, -0409 IBM 3161/319X; IBM 3151, 347X WedgesIK-0413 Wyse 50 WedgeIK-0500 NCR 2152 Tel Kybd WedgeIK-0600 NCR 2151 Tel Kybd WedgeIK-0700 NCR 280 Kybd WedgeIK-0800 — 0803 Standard RS-232CIK-0900 Fujitsu 9000 OCRIK-0901 Fujitsu 7770, 7880, 7990, 8770 OCRIK-0902 IBM 3653, 3683/3684 OCRIK-1001, -1002 NCR 2152, 2257, 2950; 215X, 7050 OCIAIK-1003, -1004 Nixdorf 8812 OCIA; NCR 2126-1120 OCIA
Preliminary7Quick ReferenceIK-1100 IBM 4683/93 Port 9BIK-1200, -1201 IBM 3178; IBM 3278 WedgesIK-1300 Wyse 60, 85, 150, 160, 185 WedgesIK-1301 HP 7000/XX, 239X WedgesIK-1400 DEC VT 2XX/3XX/4XX WedgesIK-1500, -1501 Dual RS-232C
Preliminary8P 370/470 ScannerSingle Port RS-232Dual Port RS-232In some cases, two bar codes may correspond to one interface type; this happens when different software revisions exist for the same host type. If there are two bar codes for your host type, try the first bar code; if that does not work, then try the second one.Four Options for Dual Port RS-232 FollowFor IK-1500, Port 1 = Male, TxD on Pin 2; Port 2 = Female, TxD on Pin 3.For IK-1501, Port 1 = Male, TxD on Pin 3; Port 2 = Female, TxD on Pin 2.Dual Port RS-232: Transmit and Receive from Port 1Dual Port RS-232: Transmit to Ports 1 and 2 — Receive from Port 1
Preliminary9Quick ReferenceDual Port RS-232: Transmit to Ports 1 and 2 — Receive from Port 2Dual Port RS-232: Transmit and Receive from Port 2IBM 3653 Keyboard WedgeIBM PS2-30 and ClonesIBM PC/AT, IBM PS2-50/55SX/60/70/80 and ClonesIBM PC/XT And Clones
Preliminary10P 370/470 ScannerIBM 3683/3684 Tel 35 Keyboard WedgeIBM 3683/3684 Calc 116 Keyboard WedgeIBM 3683/3684 Calc 35 Keyboard WedgeIBM 3683/3684 Calc 48 Keyboard WedgeIBM 3683/3684 Tel 48 Keyboard WedgeIBM 3683/3684 Tel 116 Keyboard Wedge
Preliminary11Quick ReferenceNCR 255/2152/2154/2155, NCR 2126-1120NCR 2157/2257/7050, NCR “S” 7052 OCIANCR 280 Keyboard WedgeNCR 2152 (Tel) Keyboard WedgeNCR 2152 (Calc) Keyboard WedgeNCR 2151 (Calc) Keyboard WedgeNCR 2151 (Tel) Keyboard Wedge
Preliminary12P 370/470 ScannerNixdorf 8812 OCIANCR “S” 2950 OCIANCR 7052 Keyboard WedgeNCR “F” 7052 OCIAICL 9505/9507/9518/9520 OCIASpectra Physics OCIA
Preliminary13Quick ReferenceHP 239XIBM 4683/4684 Port 17IBM 3653/3683/3684 OCRIBM 4683/4684 Port 9B 4693IBM 4683/4684 Port 5B 4693Fujitsu 7770/7880/7990/ 8770/9000 OCR
Preliminary14P 370/470 ScannerDEC 420 (Later Software Revision)IBM 3178HP 700-9XDEC VT 2XX/3XX/4XXIBM 319X/347X/348X Telex Memorex 122IBM 3278
Preliminary15Quick ReferenceWyse 50 (ASCII Keybd)Wyse 60/30/160 (ASCII Keybd)IBM 3180 (Later Software Revision)Telex Memorex 88IBM 3151/316XIBM 3179/3180
Preliminary16P 370/470 ScannerWyse 85/150+/185/160 (ANSI 105 Keybd)HP 2392 (Later Software Revision)Wyse 60/160 (PC Keybd)Wyse 60/150 (ANSI 101 Keybd)
Preliminary17Quick ReferenceProgram Default ParametersScanning the SET DEFAULTS bar code returns all parameters to the values listed in the Default Table, which appears at the end of this guide.Other customized programming must be performed through bar codes available in the P 370/470 Product Reference Guide or Advanced Programmer’s Guide.With this set, you are ready to scan bar codes.Set Transmission Frequency (Optional)The scanner and base can communicate on a number of different channel frequencies, which varies by country. In most countries, there are 80 available channels (numbered 2 through 81); in France, there are only 9 channels (numbered 46 through 54).The initial transmission frequency is determined by the base’s unique address, so neighboring systems operate on different channels without interfering with each other. Occassionally, there may be noticeable interference on a channel from some other source of radio transmissions. The system has been programmed to change the channel automatically if it detects excessive interference, but the channel may also be changed manually if there are communications problems.To set the transmission frequency, scan the SELECT CHANNEL NUMBER bar code appropriate for your country. Then scan two numeric bar codes to set the two-digit channel number within the allowable range (46 through 54 in France, 02 through 81 elsewhere).SET DEFAULTS
Preliminary18P 370/470 ScannerSet Transmission FrequencyScan this bar code for all countries except France.Scan this bar code for France only.SELECT CHANNEL NUMBER (02-81)SELECT CHANNEL NUMBER (46-54)
Preliminary19Quick Reference01234
Preliminary20P 370/470 Scanner56798CANCEL
Preliminary21Quick ReferenceRecharging the BatteryWhen necessary, recharge the batteries. To do so with the base/charger:• Connect the power supply to the power input port on the front panel of the base/charger, as illustrated below. • Connect the power supply to a receptacle supplying AC power of the proper voltage level. • Then place the scanner into the base/charger cradle, so that the nose of the scanner and tip of the handle fit snugly into the receptacles. Check the charge status indicator (blinking rapid-ly = fully charged) for full charge, which occurs in less than two hours. However, the scanner can be used on less than full charge.Charge Status LED IndicationsOn the base/charger, there is a red LED indicator which uses flashing patterns to indicate the current charger status. The red Charge Status LED indicates the following conditions:•RED LED OFF — The scanner is not properly inserted or the battery is not functioning properly.•RED LED blinking slowly (1/8 sec. ON, 3/8 sec. OFF) — Bat-tery charge is pending. This can occur if the batttery tempera-ture is too high or low or if the battery is deeply discharged. After several minutes, normal charging should begin.•RED LED ON — The battery is actively charging. Charging will complete in less than 2 hours.•RED LED blinking rapidly (1/8 sec. ON, 1/8 sec. OFF) — Battery charging is complete.
Preliminary22P 370/470 ScannerInstalling or Changing the Battery1. Slide the battery compartment release latch down and remove the battery compartment cover.2. Slide the battery towards the bottom of the scanner and then pull the bottom of the battery up and out of the scanner.Replacing the Battery1. Seat the battery fully in the scanner and then slide it up the handle.2. Replace the battery compartment cover and slide the release latch up to secure the cover in place.BatteryCompartmentCover Battery Release Latch
Preliminary23Quick ReferenceTroubleshootingIf the scanner does not work after you’ve followed these operating instructions:• Check the system power.• Check that scanning is enabled.• Check that the battery is installed correctly.• Check for loose cable connections.• Be sure the Phaser is programmed to read the type of bar code you are trying to scan.• Check to be sure the symbol is not defaced.• Check that the correct power supply is attached to the base/charger.• Check for correct host interface cable or loose cable connec-tions at the base/charger and host device.• Make sure the device is programmed to read the type of bar code you want to scan.• Try scanning similar symbols of the same code type.• Make sure the scanner and base/charger have been successful-ly paired.• Be sure you’re within the proper scanning and transmission range (30 to 50 ft., or 9 - 15 meters).You get frequent communication errors (6 beeps after decode)• Check that you are within transmit range.• Check that the scanner is successfully paired with the base/charger.You get frequent communication errors (6 beeps after decode):• Check that the base/charger is powered up and that its cable connections are secure.
Preliminary24P 370/470 ScannerNote: If after performing these checks the symbol still does not scan, contact your distributor or call the Symbol Sup-port Center.CleaningWipe the scanner window periodically with a lens tissue or other material suitable for cleaning optical material, such as eyeglasses. Caution: Do not pour, spray or spill any liquid on the scanner.
Preliminary25Quick ReferenceTest SymbolsCode 128EAN-813 Mil UPCCode 39
Preliminary26P 370/470 ScannerRegulatory InformationScanner Labeling
Preliminary27Quick ReferenceIn accordance with Clause 5, IEC 0825 and EN60825, the following information is provided to the user:ENGLISH HEBREWCLASS 1 CLASS 1 LASER PRODUCTCLASS 2 LASER LIGHTDO NOT STARE INTO BEAMCLASS 2 LASER PRODUCTDANISHKLASSE 1 KLASSE 1 LASERPRODUKT ITALIANKLASSE 2 LASERLYF CLASSE 1PRODOTTO AL LASER DI CLASSE 1SE IKKE IND I STRÅLEN CLASSE 2LUCE LASERKLASSE 2 LASERPRODUKT NON FISSARE IL RAGGIOPRODOTTO AL LASER DI CLASSE 2DUTCHKLASSE 1 KLASSE-1 LASERPRODUKT NORWEGIANKLASSE 2 LASERLICHT KLASSE 1LASERPRODUKT, KLASSE 1NIET IN STRAAL STAREN KLASSE 2LASERLYS IKKE STIRR INN I LYSSTRÅLENKLASSE-2 LASERPRODUKT LASERPRODUKT, KLASSE 2FINNISH PORTUGUESELUOKKA 1 LUOKKA 1 LASERTUOTE CLASSE 1PRODUTO LASER DA CLASSE 1LUOKKA 2 LASERVALOÄLÄ TUIJOTA SÄDETTÄ CLASSE 2LUZ DE LASER NÃO FIXAR O RAIO LUMINOSOLUOKKA 2 LASERTUOTE PRODUTO LASER DA CLASSE 2FRENCH SPANISHCLASSE 1 PRODUIT LASER DE CLASSE 1 CLASE 1 PRODUCTO LASER DE LA CLASE 1CLASSE 2 LUMIERE LASER CLASE 2 LUZ LASERNE PAS REGARDER LE RAYON FIXEMENT NO MIRE FIJAMENTE EL HAZPRODUIT LASER DE CLASSE 2 PRODUCTO LASER DE LA CLASE 2GERMAN SWEDISHKLASSE 1 LASERPRODUKT DER KLASSE 1 KLASS 1 LASERPRODUKT KLASS 1KLASSE 2 LASERSTRAHLEN KLASS 2 LASERLJUS STIRRA INTE MOT STRÅLENNICHT DIREKT IN DEN LASERSTRAHL SCHAUEN LASERPRODUKT KLASS 2LASERPRODUKT DER KLASSE 2Radio Frequency Interference RequirementsThis device has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the Federal Communications Commissions Rules and Regulation. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Preliminary28P 370/470 ScannerHowever, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Re-orient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.This device complies with FCC Part 15. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.Radio Frequency Interference Requirements - CanadaThis device complies with RSS 210 of Industry & Science Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.This Class B digital apparatus complies with Industry Canada Standard ICES-003.Cet appareil numérique de la classe B est conform à la norme NMB-003 d’Industrie Canada.CE Marking and European Union ComplianceProducts intended for sale within the European Union are marked with the CE Mark which indicates compliance to applicable Directives and European Normes (EN), as follows. Amendments to these Directives or ENs are included:Applicable Directives• Electromagnetic Compatibility Directive 89/336/EEC• Low Voltage Directive 73/23/EECApplicable Standards• EN 55 022 - Limits and Methods of Measurement of Radio Interference Charac-teristics of Information technology Equipment• EN 50 082-1:1997 - Electromagnetic Compatibility - Generic Immunity Stan-dard, Part 1: Residential, commercial, Light Industry• IEC 1000-4-2(1995-01) - Electromagnetic compatibility (EMC) - Part 4:Testing and measurement techniques - Section 2: Electrostatic discharge immunity test.• IEC 1000-4-3(1995-03) - Electromagnetic compatibility (EMC) - Part 4:Testing and measurement techniques - Section 3: Radiated, radio-frequency, electromag-netic field immunity test.
Preliminary29Quick Reference• IEC 1000-4-4(1995-01) - Electromagnetic compatibility (EMC) - Part 4:Testing and measurement techniques - Section 4: Electrical Fast transient/burst immunity test.• EN 60 950 + Amd 1 + Amd 2 - Safety of Information Technology Equipment Including Electrical Business Equipment• EN 60 825-1 (EN 60 825) - Safety of Devices Containing Lasers RF DevicesSymbol’s RF products are designed to be compliant with the rules and regulations in the locations into which they are sold and will be labeled as required. The majority of Symbol’s RF devices are type approved and do not require the user to obtain license or authorization before using the equipment. Any changes or modifications to Symbol Technologies equipment not expressly approved by Symbol Technologies could void the user’s authority to operate the equipment.Laser DevicesSymbol products using lasers comply with US 21CFR1040.10, Subchapter J and IEC825/EN 60 825 (or IEC825-1/EN 60 825-1, depending on the date of manufacture). The laser classification is marked on one of the labels on the product.Class 1 Laser devices are not considered to be hazardous when used for their intended purpose. The following statement is required to comply with US and international regulations:Caution: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure.Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful.Service InformationBefore you use the unit, it must be configured to operate in your facility’s network and run your applications.If you have a problem running your unit or using your equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact the Symbol Support Center:United States 1-800-653-5350 Canada 905-629-7226United Kingdom 0800 328 2424 Asia/Pacific 337-6588 Australia 1-800-672-906 Austria 1-505-5794Denmark 7020-1718 Finland 9 5407 580France 01-40-96-52-21 Germany 6074-49020Italy 2-484441 Mexico 5-520-1835Netherlands 315-271700 Norway 66810600South Africa 11-4405668 Spain 9-1-320-39-09
Preliminary30P 370/470 ScannerWarrantySymbol Technologies, Inc. (“Symbol”) manufactures its hardware products in accordance with industry-standard practices. Symbol warrants that for a period of twelve (12) months from date of shipment, products will be free from defects in materials and workmanship. This warranty is provided to the original owner only and is not transferable to any third party. It shall not apply to any product (i) which has been repaired or altered unless done or approved by Symbol, (ii) which has not been maintained in accordance with any operating or handling instructions supplied by Symbol, (iii) which has been subjected to unusual physical or electrical stress, misuse, abuse, power shortage, negligence or accident or (iv) which has been used other than in accordance with the product operating and handling instructions. Preventive maintenance is the responsibility of customer and is not covered under this warranty. Wear items and accessories having a Symbol serial number, will carry a 90-day limited warranty. Non-serialized items will carry a 30-day limited warranty.Warranty Coverage and ProcedureDuring the warranty period, Symbol will repair or replace defective products returned to Symbol’s manufacturing plant in the US. For warranty service in North America, call the Symbol Support Center at 1-800-653-5350. International customers should contact the local Symbol office or support center. If warranty service is required, Symbol will issue a Return Material Authorization Number. Products must be shipped in the original or comparable packaging, shipping and insurance charges prepaid. Symbol will ship the repaired or replacement product freight and insurance prepaid in North America. Shipments from the US or other locations will be made F.O.B. Symbol’s manufacturing plant. Symbol will use new or refurbished parts at its discretion and will own all parts removed from repaired products. Customer will pay for the replacement product in case it does not return the replaced product to Symbol within 3 days of receipt of the replacement product. The process for return and customer’s charges will be in accordance with Symbol’s Exchange Policy in effect at the time of the exchange. Customer accepts full responsibility for its software and data including the appropriate backup thereof. Repair or replacement of a product during warranty will not extend the original warranty term. Sweden 84452900Latin America Sales Support 1-800-347-0178 Inside US+1-561-483-1275 Outside USEurope/Mid-East Distributor Operations Contact local distributor or call+44 118 945 7360
Preliminary31Quick ReferenceSymbol’s Customer Service organization offers an array of service plans, such as on-site, depot, or phone support, that can be implemented to meet customer’s special operational requirements and are available at a substantial discount during warranty period. GeneralExcept for the warranties stated above, Symbol disclaims all warranties, express or implied, on products furnished hereunder, including without limitation implied warranties of merchantability and fitness for a particular purpose. The stated express warranties are in lieu of all obligations or liabilities on part of Symbol for damages, including without limitation, special, indirect, or consequential damages arising out of or in connection with the use or performance of the product. Seller’s liability for damages to buyer or others resulting from the use of any product, shall in no way exceed the purchase price of said product, except in instances of injury to persons or property. Some states (or jurisdictions) do not allow the exclusion or limitation of incidental or consequential damages, so the proceeding exclusion or limitation may not apply to you. Ergonomic RecommendationsCaution: In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are meeting with your company’s safety programs to prevent employee injury.• Reduce or eliminate repetitive motion• Maintain a natural position• Reduce or eliminate excessive force• Keep objects that are used frequently within easy reach• Perform tasks at correct heights• Reduce or eliminate vibration• Reduce or eliminate direct pressure• Provide adjustable workstations• Provide adequate clearance• Provide a suitable working environment• Improve work procedures.
Preliminary72-38493-01Revision .1 — June 1999Symbol Technologies, Inc. One Symbol Plaza Holtsville, NY 11742-1300

Navigation menu