Systems and Technology STAVL1321 2G/3.5G module, HE910-NAG, HE910-NAR, HE910-NAD User Manual U3

Download:
Mirror Download [FCC.gov]
Document ID	2163510
Application ID	me/aG/1eB2eIHkpBqCS0Bw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	130.84kB (1635473 bits)
Date Submitted	2014-01-12 00:00:00
Date Available	2014-07-12 00:00:00
Creation Date	2014-01-07 11:45:30
Producing Software	PDF-XChange Viewer [Version: 2.0 (Build 42.9) (Nov 18 2009; 15:44:46)]
Document Lastmod	2014-01-07 16:09:16
Document Title	Microsoft Word - U3.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	rico_you

CAREU U3 Vehicle Tracker
User Guide
Version: 0.1
Reference No.: AVL-CU-U3-00-1115UEN
Date: July 10, 2013
SYSTEMS & TECHNOLOGY CORP.
General Information
If any breakdown occurs due to the operation of the described product or users’ improper handling
in accordance with the instructions of the document, S&T shall be liable for the General Conditions
based on the delivery of the described product and the content of the document. This product is not
designed for the use of life support appliances, devices or systems and thence a malfunction of the
product might reasonably be expected to make personal injury. S&T customers using or selling this
product for such applications will take the risk on their own; therefore, it must be agreed S&T will
be fully indemnified from any damages due to illegal use or resale. All information in this document
is subject to change without notice at any time.
Disclaimer
The information, specification, images and photos in this user guide are subject to change without
notice and without obligation to notify any person of such revision change.
Copyright
This user guide, including all photographs, illustrations and software, to name a few, is protected
under international copyright laws, with all rights reserved. This document contains confidential,
restricted and proprietary information that it has been exclusively prepared for the internal use of
certain designated S&T employees, and may not be duplicated or distributed, in whole or in part,
without the prior written consent of S&T’s authorized delegates. Any illegal copying and disclosure
of the document are absolutely prohibited, and violators are liable to the damages caused.
© Systems & Technology Corp. All Rights Reserved
CAREU U3 Vehicle Tracker User Guide
Table of Contents
Chapter 1. Introduction ...................................................................................................................... 1
1.1 Features ............................................................................................................................... 1
1.2
Scope .................................................................................................................................. 2
1.3
About CAREU U3 ............................................................................................................. 2
1.4
Hardware Architecture ................................................................................................... 3
1.5
Related Document ........................................................................................................... 4
Chapter 2. Taking a Tour of CAREU U3 ...................................................................................... 5
2.1
Dimensions........................................................................................................................ 5
2.2
Front View.......................................................................................................................... 6
2.3
Rear View ........................................................................................................................... 6
Chapter 3. Getting Started with CAREU U3 .................................................................................. 7
3.1
Hardware Installation...................................................................................................... 7
3.2
Connector Pin Assignment ......................................................................................... 13
3.3
LED Indicator .................................................................................................................. 15
3.4
USB Device Driver Installation................................................................................... 16
3.5
Device Configuration .................................................................................................... 23
3.6
Communication Settings ............................................................................................. 27
3.7
GPS Tracking Configurations..................................................................................... 29
3.8
Firmware Upgrade ......................................................................................................... 32
Chapter 4. Technical Specification ............................................................................................... 33
Chapter 1
CAREU U3 Vehicle Tracker User Guide
Chapter 1. Introduction
Thank you for your purchasing the CAREU U3
Vehicle Tracker. We are very pleased to introduce
you our excellent product, and you will enjoy great
benefits by applying such a smart device. The
CAREU U3 Vehicle Tracker is an all-in-one
device that integrates multiple applications of GPS
(Global Position System), GSM (Global System
for Mobile Communication) and GIS (Geographic
Information Systems) with each other.
Designed with the latest GPS technology, the CAREU U3 delivers positioning message by GSM
wireless transmission to GIS platform, and then helps back-end users proceed with the analysis
and the applications of vehicle transport, management, anti-theft, security and tracking.
1.1
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Chapter 1
Multiple serial ports and easy installation.
Voices, FTP, SMS, GPRS TCP/UDP Communications
Geo-fencing reports (circular/polygon/rectangle zones)
Remote configuration
Real-time tracking (time, distance interval or intelligent mode, and heading)
Intelligent power management
1-Wire® interfaces supported (optional)
Power low/lost alarm
Built-in voice communication
Built-in interactive voice response
Journey report wireless download
GSM/GPRS simultaneously
User-defined reports
Firmware upgrade over the air (via GPRS from FTP)
GPS antenna disconnect/cut alarm
Up to 150,000 data log capacity
CAN-bus support (optional)
CAREU U3 Vehicle Tracker User Guide
1.2
Scope
This document will guides you to start the CAREU U3 Vehicle Tracker. However, as this
document contains basic device configuration only, please see the CAREU U3 Protocol
Document for the advanced information.
1.3
About CAREU U3
The CAREU U3 Vehicle Tracker transmits the wireless signals such as location, peripheral,
and vehicle control data to a control center. The onboard GPS receiver provides users with
location data including speed, direction, mileage and altitude. It uses an onboard GSM/
GPRS module to accomplish wireless transmission.
A microcontroller can probe location and command data at regular intervals, derive actions
from location, peripheral and control data, and execute such actions.
Among the best features of the CAREU U3 Vehicle Tracker, in particular, they transmit data
in ASCII mode (Intellitrac X Series compatible mode) or binary mode.
Peripheral data indicates the status of various peripherals connected to and/or controlled by
the device. The peripherals include, but not limited to, door locks/un-locks, starter interrupt,
ignition, battery, engine and panic button.
The firmware in the device applies intelligent filtering to overcome coverage limitations for
both GPS and GSM/GPRS networks.
Motion sensor controls the status of the device, whether in sleep, idle or fully-powered
mode, and thereby controls the amount of current consumed by the device.
Backup battery and tamper sensing GPS Antennas primarily indicate the loss of Main
Power and the interruption of GPS antenna connectivity.
The device supports over-the-air firmware upgrade to deliver additional functionality without
physically touching the device once installed.
In consideration of technicality and marketability, the CAREU U3 has so many excellences
to be competitive enough to stand out in the market. With regard to the technicality, the
CAREU U3 saves and records more data even under inactive communication staus, and
it also provides better power management, coexistence of GPRS and SMS modes, 1-Wire®
interface, direct connection to Temperature Sensor, and up to three serial ports. When it
comes to the marketability, the CAREU U3 users are provided with the convenience that
its firmware can be upgraded through mini USB without disassembling the device.
Chapter 1
CAREU U3 Vehicle Tracker User Guide
1.4
Hardware Architecture
As hardware is concerned, the CAREU U3 is comprised of a micro-controller, regulator,
GPS receiver, GSM/GPRS modem, G-Force sensor, flash memory data storage,
audio interface, I/Os interface, serial ports and LED status indicators.
Optional
SPI
CAN
FLASH
External
Device
G-Sensor
I/O Ports
GPS
USB
CPU
Power
GSM
Modem
MIC
Audio
Speaker
•
RS232
Audio
AMP
Users can connect PC's HyperTerminal to the Diagnostic/setting port for the AVL
configuration.
•
G-Sensor for car accident prevention, car tow-away warning and power management.
•
The audio interface supports hand-free phone call.
•
GPIO that connects to any customer monitoring points by door switch, anti-thief or
actuators.
•
The A/D input that connects the analog signal sensor to the AVL, such as the fuel or
temperature sensor.
Chapter 1
CAREU U3 Vehicle Tracker User Guide
1.5
Related Document
[1] CAREU U3 Protocol Document
Chapter 1
CAREU U3 Vehicle Tracker User Guide
Chapter 2. Taking a Tour of CAREU U3
This chapter will guide you to the major connectors of the U3 device.
2.1
Dimensions
31.10
72.00
108.00
Dimensions: 108mm x 72mm x 31mm
Chapter 2
CAREU U3 Vehicle Tracker User Guide
2.2
Front View
No.
Name
Description
PWR
I/O
SERIAL
GSM
SMA Connector for GSM External Receiver
GPS
SMA Connector for GPS External Antenna
Power Connector for Car Battery
Input/Output Connector including basic I/O, RS-232
Serial Connector
2.3
Rear View
Mini USB Connector
Chapter 2
CAREU U3 Vehicle Tracker User Guide
Chapter 3. Getting Started with CAREU U3
To install the the CAREU U3 device, follow the instructions below for basic operations.
3.1
Hardware Installation
1.
SIM Card Installation
•
Remove the screw at the bottom of the device to open it. Then you will find the SIM
card slot inside.
•
Insert your SIM card into the device with SIM card's gold area down and the
notched corner toward the notched edge of the SIM card socket. Make sure it is
installed correctly in place. Reinstall the cover.
SIM Card
Chapter 3
CAREU U3 Vehicle Tracker User Guide
2.
GPS Antenna Connection
• Connect the GPS antenna to the SMA connector jack on the front side of the device
(circled as the illustration below) by completely screwing the GPS antenna's plug
connector.
• It is recommended that a matching torque 7-10 inch pounds (80-110 N.cm) should
be used for the SMA connector.
3.
GSM Antenna Connection
• Connect the GSM antenna to the SMA connector jack on the front side of the device
(circled) as illustration below) by completely screwing the GSM antenna's plug
connector.
• It is recommended that a matching torque 7-10 inch pounds (80-110 N.cm) should
be used for the SMA connector.
Chapter 3
CAREU U3 Vehicle Tracker User Guide
4.
Power, RS-232, and I/O Cable Connection
• Connect 4-wire power cable to the power connector on the front side of the
CAREU U3 device (8~30V)
• Connect the 8-wire cable to the CARE U3 device which enables the connection of
the CARE U3 to your system and also to related peripherals.
Only these 4 pins
are to connect to
your PC.
Chapter 3
CAREU U3 Vehicle Tracker User Guide
• Good Wiring Installation
Please reserve approximately 1 cm accommodation before folding the cable.
Folding cable directly on connector may result in poor contact on connector pin
Correct way of folding cable
1cm
1cm
Incorrect way of folding cable
10
Chapter 3
CAREU U3 Vehicle Tracker User Guide
5. I/O Cable Connection
6.
Mini USB Cable Connection
7.
G-Sensor Installation Consideration
The device uses a 3-axis G-Force sensor to detect the vehicle motion and the impact
on the vehicle. The X, Y and Z axis definition will be affected by the location of device
installation.
Chapter 3
11
CAREU U3 Vehicle Tracker User Guide
8.
Microphone Installation (Optional)
Connect the microphone set to the 8-wire cables first. Plug the connector of the 8-wire
cable completely into to the seial port on the front side of the device. See the
illustration below.
9.
Speaker Installation (Optional)
Connect the speaker set to the 8-wire cables first. Plug the connector of the 8-wire
cable completely into to the seial port on the front side of the device. See the
illustration below.
12
Chapter 3
CAREU U3 Vehicle Tracker User Guide
3.2
Connector Pin Assignment
1 3
2 4
1 3 5 7 9
2 4 6 8 10
1 3 5 7 9 11 13 15
2 4 6 8 101214 16
Connector Pin Definition
1. PWR Connector
Pin# Signal Name
Description
I/O
Remark
DC Vin = +8 ~ +30V
Normal = 70mA @ 12V
DC IN
Power supply input
GND
Signal ground
----
Ignition
Ignition(ACC) Input
DC Vin = +30 ~ +7V (Active high)
Output1
Open-Collector
Output1
Imax = 300mA
2. I/O Connector
Pin# Signal Name
Description
I/O
Analog Input
Analog Input 2
DC VIN = +30V ~ 0V (default)
Input 3
(Optional)
Positive Trigger
input 3
DC VIN = +30V ~ +7V (High
Active)
Input 4
Positive Trigger
input 4
DC VIN = +30V ~ +7V (High
Active)
Input 1
Negative Trigger
input 1
DC VIN = +6V ~ 0V (Low Active)
Input 2
Negative Trigger
input 2
DC VIN = +6V ~ 0V (Low Active)
Analog Input
Analog input 1
DC VIN = +30V ~ 0V
GND
Signal ground
----
Output 2
Open-Collector
Output 2
Chapter 3
Remark
Imax = 300mA
13
CAREU U3 Vehicle Tracker User Guide
Pin# Signal Name
Description
I/O
Remark
Output 3
Open-Collector
Output 3
Imax = 300mA
CAN H
CAN High
VI = 2.75V ~ 4.5V
10
CAN L
CAN Low
VI = 0.5V ~ 2.25V
3. Serial Connector
Pin#
Signal Name
Description
IO
Remark
Vout1
Supply voltage output
Vo = 5V ( Vout 1~3 Total Imax =
500mA )
GND
Signal ground
－
TX1
RS-232 Data output
RX1
RS-232 Data input
Vout2
Supply voltage output
GND
Signal ground
－
TX2
RS-232 Data output
RX2
RS-232 Data input
Supply voltage output
1-Wire® Data input
11
GND
1-Wire®_
GND
TX3
12
RX3
RS-232 Data input
13
14
15
16
SPK+
SPKMIC+
MIC-
Audio output
Audio output
Microphone Input
Microphone Input
10
14
Vout2
1-Wire®
Signal ground
1-Wire® ground
－
－
RS-232 Data output
Support Accessories:
Garmin FMI PND, MDT M1/M7/
M7+
Vo = 5.0V, (Vout1~3 Total Imax
= 500mA)
Support
Audio Box,
The Vout3 is not available on the
1-Wired Version
It is only available on the 1-Wired
Version
(Optional)
Chapter 3
CAREU U3 Vehicle Tracker User Guide
3.3
LED Indicator
1. GPS LED Indicator
Power Mode
Power Off
GPS Status
N/A
GPS LED
Off
Low Power
N/A
Off
Full Power
Acquiring
Flash Red (five times/second)
Full Power
Tracking
Solid Red
Power Mode
Power Off
GSM/GPRS Status
N/A
GSM LED
Off
Low Power
Full Power
N/A
Acquiring
Off
Flash Red (three times/
second)
Full Power
Registered
Solid Red
2.
Chapter 3
GSM LED Indicator
15
CAREU U3 Vehicle Tracker User Guide
3.4
USB Device Driver Installation
The CAREU U3 communicates with your host computer by either RS-232 or USB
interface.
In some newer editions of Windows XP, the CAREU U3 device can be installed as a "virtual
COM port" device whereby the CAREU U3 would automatically access Windows XP's
inbox USB drivers. While in some other earlier editions of Windows XP, you would need to
manually install the USB driver for the CAREU U3 device. In the following content of this
section, you will be guided to how the installation can be done in both cases.
To install the device driver for the CAREU U3, connect the CAREU U3 device to your
system with an USB cable as mentioned in Mini USB Cable Connection on page 11.
As soon as the connection is made between the CAREU U3 and your computer, a balloon
appears above the notification area saying an USB device is found.
Click on this balloon to start the [Found New Hardware] wizard.
Select No, not this time. Press the Next button to proceed.
16
Chapter 3
CAREU U3 Vehicle Tracker User Guide
1. Automatic Installation
If the wizard prompts to help you install the software for "STMicroelectronics Virtual
COM Port". Select Install the software automatically (Recommended). Press the
Next button to proceed.
The wizard proceeds to install the driver.
Chapter 3
17
CAREU U3 Vehicle Tracker User Guide
The installation completes.
In [Device Manager], the CAREU U3 device is included under Ports (COM & LPT) as
"STMicroelectronics Virtual COM Port". COM port number is displayed as well.
18
Chapter 3
CAREU U3 Vehicle Tracker User Guide
2. Manual Installation
After you select No, not this time, if the wizard only prompts to help you install software
for "USB device", you need to manually install the driver. Select Install from a list or
specific location (Advanced). Press the the Next button to proceed.
Chapter 3
19
CAREU U3 Vehicle Tracker User Guide
Select Search for the best driver in these locations. Check Include this location
in the search. Press the Browse button to assign where your the CAREU U3 device
driver locates on your local disk.
Press the OK button.
You can download the USB device driver from http://www.systech.com.tw/downloads.php.
20
Chapter 3
CAREU U3 Vehicle Tracker User Guide
Press the Next button to proceed.
The wizard proceeds to install the driver.
Chapter 3
21
CAREU U3 Vehicle Tracker User Guide
The installation completes.
In [Device Manager], the CAREU U3 device is included under Ports (COM & LPT) as
"S&T Tracker". COM port number is displayed as well.
22
Chapter 3
CAREU U3 Vehicle Tracker User Guide
3.5
Device Configuration
1. In Windows XP desktop, click Start | All Programs | Accessories |
Communications | HyperTerminal.
2. If you are prompted to input the information of your location, complete them to proceed.
3. On the File menu of HyperTerminal, click New Connection.
4. In the Name box, type a name that describes the connection. In the Icon box, click
an appropriate icon. Press the OK button to proceed.
5. For Com port properties, configure as follows:
Baud Rate -->
Data Bits -->
Parity -->
Stop Bits -->
Flow Control -->
Chapter 3
115200 bps
None
None
23
CAREU U3 Vehicle Tracker User Guide
6. In the connection that you have just set up, click File | Properties. Select the
[Connect To] tab. From the [Connect using] drop down list, select the correct com
port by checking it up at Windows XP's [DeviceManager] as previously mentioned
on page 29 and page 33. Go there by clicking Start | Control Panel | System | Hardware |
Device Manager.
24
Chapter 3
CAREU U3 Vehicle Tracker User Guide
7. In the File menu, click Properties. Click the [Settings] tab. Press the ASCII Setup
button.
8. In the [ASCII Sending] group box. Select both Send line ends with line feeds and
Echo typed characters locally. Press the OK button.
Chapter 3
25
CAREU U3 Vehicle Tracker User Guide
9. Connect your the CAREU U3 device to power as mentioned in Power, RS-232, and
I/O Cable Connection on page 9. The device startup message will be displayed.
10. In [HyperTerminal] window, type in the command "AT$VERSION?" and press the
Enter key. The hardware and firmware version will show. As long as your
[HyperTerminal] window appears as the screenshot below, a connection between the
device and your system has already been built up and working. It is time to send all
configuration commands.
26
Chapter 3
CAREU U3 Vehicle Tracker User Guide
3.6
Communication Settings
The CAREU U3 Vehicle Tracker communicates with your control center by either SMS or
GPRS (TCP/UDP). Before the device is installed into a vehicle, communication
parameters should be set.
1.
SMS Configuration
Use AT$SMSDST command to set a SMS control center phone number or short code.
For example, if the SMS control center phone number is +886123456789, the
AT$SMSDST command to be issued into HyperTerminal should be:
AT$SMSDST=+886123456789
OK
Then you can try to use cellular phone or SMS gateway to send a SMS message to
the CAREU U3 device. Send a SMS message --> "AT$MODID?"
Device will response:
$MODID=101000001
OK
This proves a successful mobile phone SMS connection.
Chapter 3
27
CAREU U3 Vehicle Tracker User Guide
2.
GPRS Configuration
Set GPRS servers by using the folloiwng commands:
AT$APN=internet,username,password (APN=internet, Username=username,
Password=password) OK
AT$HOSTS=1,0,60.148.19.10,6000
(Server IP address = 60.148.19.10 and Port number =6000)
OK
AT$RETRY=5,10 (Message retry settings)
OK
AT$IPTYPE=1 (Using TCP/IP mode)
OK
AT$GPRSEN=1 (GPRS enable)
OK
AT$HB=60,1 (Heartbeat setting)
OK
Please refer to the CAREU U3 Protocol Document for more command details.
28
Chapter 3
CAREU U3 Vehicle Tracker User Guide
3.7
GPS Tracking Configurations
After the device communication settings are done, the remote GPS tracking is ready to
function. The setting of GPS tracking can be done by using AT$PDSR command. For
example,
AT$PDSR=1,30,0,0,2,0,0,1,1 (Tracking through GPRS by time interval 30 seconds)
OK
For simple testing GPRS, run the TCP Server U-Series software which is provided by
S&T. It is simple server software that can wait for device connection and data.
Chapter 3
29
CAREU U3 Vehicle Tracker User Guide
For advanced testing, you need the software Intelli TracerPlus. Please
request this software through your sales contact.
You can also apply for a testing account from S&T's FleetWeb solution through your sales
contact.
30
Chapter 3
CAREU U3 Vehicle Tracker User Guide
The main page of the Intelli FleetWeb appears as below:
Chapter 3
31
CAREU U3 Vehicle Tracker User Guide
3.8
Firmware Upgrade
The firmware of the CAREU U3 can only be updated through USB interface. With the
firmware loader tool provided by S&T, firmware update can be done for the device. Such
firmware loader runs on Windows-based systems. To upgrade the firmware, follow the
procedure below:
1).
2).
3).
4).
Connect the device to your PC with the USB cable.
Connect the device to power.
Power on the device.
Run ServerUSeries.exe. A window displays as follows:
5).
Press browse the button
6).
7).
Press the Start button to run the firmware program.
After the writing progresses to 100%, it takes about 20 seconds for the update
to completes.
Firmware update completes.
8).
32
to browse to the firmware provided by S&T.
Chapter 3
CAREU U3 Vehicle Tracker User Guide
Chapter 4. Technical Specification
Characteristics
Dimensions (L x W x H) 108 x 72 x 31mm (with connector)
Weight 165g
Radio Performance
GSM Frequency Quad-band 850/900/1800/1900MHz
Operating Bands B5, B2, B4
GSM Functionality / GPRS
GPRS Mode Multislot class 10
GPRS Coding Scheme CS1,CS2,CS3 and CS4
GSM Antenna External
SIM Interface SIM card 1.8V, 2.9V supported
GPS Functionality
Receiver 50 channels
Sensitivity (Tracking) -160dBm
Antenna Type External GPS active antenna, 3.3V
Connector SMA female
GPS Protocol NMEA 0183 Ver3.0
Onboard Components
MCU 32-bit microcontroller
Data Memory 8MB flash
Motion Sensor 3-axes acceleration sensor
Led Indicator 2. GPS and GSM
Chapter 4
33
CAREU U3 Vehicle Tracker User Guide
Interface I/O
I/O Connector 1 connector, 10pin
3 RS-232 ports (configurable) : Standard version
Serial Connectors 2 RS-232 ports (configurable) : 1-Wire® version
Positive triggers: 2
Input Ports Negative triggers: 2
Analog Inputs: 2 (0~30V, 12 bits)
Output Ports Negative triggers: 3 (total 500mA)
Electrical
Power Source DC 8V to 30V
73 mA @ 12V (operating mode)
Power Consumption 13 mA @ 12V (standby mode)
10 mA @ 12V (deep sleep mode)
Environment
Operating Temperature –20 °C to +70 °C (without backup battery)
–20 °C to +60 °C (with backup battery)
Battery
Rechargeable Backup 1150mAH , support up to 8 days (based on data
Battery transmission every 4 hours)
Note: The specification herein is subject to change without prior notice.
34
Chapter 3
CAREU U3 Vehicle Tracker User Guide
Systems & Technology Corp. (S&T), founded in 1987, is a market leader in
Automatic Vehicle Locating (AVL) solutions, Geographical Information Systems (GIS)
and navigation. It has formed a professional development team to innovate the most
advanced and comprehensive GPS tracking products for the customers and has built
a global service network to provide non-stop services and support.
With the well-established marketing networks of over 100 distributors in the world,
S&T is your trustworthy tracking solution provider.
For more product information,
please contact S&T by Email, phone or fax.
為維護隱私權，
為維護隱私權，請妥適使用
Chapter 5
35
CAREU U3 Vehicle Tracker User Guide
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Web Site
http://www.systech.com.tw
Email
avl@systech.com.tw
Phone
+886-2-2698-1599
Fax
+886-2-2698-1211
Chapter 5
36

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2014:01:07 11:45:30Z
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2014:01:07 16:09:16+08:00
Metadata Date                   : 2014:01:07 16:09:16+08:00
Format                          : application/pdf
Title                           : Microsoft Word - U3.doc
Creator                         : rico_you
Producer                        : PDF-XChange Viewer [Version: 2.0 (Build 42.9) (Nov 18 2009; 15:44:46)]
Document ID                     : uuid:7f239106-c959-4fbc-a73e-5278ba7e1c8c
Instance ID                     : uuid:79965ba3-decc-4f75-be20-6ad6ec176f15
Page Count                      : 40
Author                          : rico_you

EXIF Metadata provided by EXIF.tools