TAIDOC TECHNOLOGY H4000BEM2 Bluetooth Module User Manual Manual
TAIDOC TECHNOLOGY CORP. Bluetooth Module Manual
Manual
Manual
Version 1.1
Product: BC4 Module
Model No. :
H4000
Date: June 12, 2009
H4000 Bluetooth Module
KEY FEATURES
Support SPP, HID, HSP,A2DP,AVRCP, BIP Profile..
Bluetooth 2.0+EDR
Power Level Class 2 (<4dBm)
High sensitivity -85dBm
Printing Antenna
APPLICATIONS
PDA and smart phone.
Digital frame with Bluetooth file transfer supporting.
GPS receiver.
Botebook PC and UMPC.
Picture
TOP VIEW
PHYSICAL SIZE 32mm X 14.5mm X 1.92mm
CONTENTS
1. Key fecture..………………………………………………………………………2
2. Applictions………………………………………………………………………...2
3. Picture…………………………………………..…………………………………..2
4. Dimension…………………………………….…………………………………….4
5. PCB footpoint……………………………….………..………………………...5
6. Diagram……………………………………..………………………………………7
7. Bundled Software……………………….………….………………………….7
8. Electrical Characteristics…………………………………………………..8
9. Contact Information…..…………………………………………………..10
10. Document History………………………………………………………….11
Hardware Pad Functions
Dimension
36
GND
GND
VDD_PA
AIO0
AIO1
RESET
SPI_MISO
SPI_CSB
SPI_MOSI
SPI_CLK
UART_CTS
UART_TX
UART_RTS
UART_RX
1V8OUT
VDD
GND
GND
PIO0
PIO1
PIO2
PIO3
PIO4
PIO6
PIO5
PIO7
USB_D-
USB_D+
PCM_CLK
PCM_IN
PCM_SYNC
PCM_OUT
H4000
TOP
VIEW
1
PIO11
PIO10
PIO8
PIO9
14.5mm
32mm
1.279.82
7.28
1.86
PCB Footprint
1.0
No.
Symbol I/O Description
1 GND - Ground
2 VDD_PA I No connection
3 GND - Ground
4 AIO(0) I/O
Programmable I/O line
5 AIO(1) I/O
Programmable I/O line
6 RESET I Reset if low
7 SPI_MISO O Synchronous serial interface data output
8 SPI_CSB I Chip select for Synchronous Serial Interface
active low
9 SPI_CLK I Synchronous serial interface clock
10 SPI_MOSI I Synchronous serial interface data input
11 UART_CTS I UART clear to send active low
12 UART_TX O UART data output
13 UART_RTS O UART request to send active low
14 UART_RX I UART data input
15 1V8OUT O 1.8V output voltage
16 VDD I 3.3V input voltage
17 GND - Ground
18 PIO(11) I/O
Programmable I/O line
19 PIO(10) I/O
Programmable I/O line
20 PIO(9) I/O
Programmable I/O line
21 PIO(8) I/O
Programmable I/O line
22 PCM_OUT O Synchronous data out
23 PCM_SYNC I/O
Synchronous data sync
24 PCM_IN I Synchronous data input
25 PCM_CLK I/O
Synchronous data clock
26 USB_DP I/O
USB data plus with selectable internal 1.5k
pull-up resistor
27 USB_DN I/O
USB data minus
28 PIO(7) I/O
Programmable I/O line
29 PIO(6)/WLAN_Active/Ch_Data
I/O
Programmable I/O line or
Optionally WLAN_Acitve/Ch_Data input for
co-existence signaling
30 PIO(5)/BT_Active I/O
Programmable I/O line or
Optionally BT_Acitve output for
co-existence signaling
31 PIO(4)/BT_Priority/Ch_Clk I/O
Programmable I/O line or
Optionally BT_Priority/Ch_Clk output for
co-existence signaling
32 PIO(3) I/O
Programmable I/O line
33 PIO(2) I/O
Programmable I/O line
34 PIO(1)/TXEN I/O
Programmable I/O line or Control output for
external PA (if fitted)
35 PIO(0)/RXEN I/O
Programmable I/O line or Control output for
external LNA (if fitted)
36 GND - Ground
Hardware Block Diagram
Main chip
CSR
BC417
Flash
8M bit
Crystal
16MHz
Balun
Frequency range :
2.400GHz ~ 2.480GHz
Bundled Software
Bluepacket FW 43.TDR11.403, support SPP-B profile .
Electrical Characteristics
Absolute Maximum Ratings
Rating Min Max
Storage temperature -40
o
C +90
o
C
Supply Voltage -0.4V 3.7V
Recommended Operating Conditions
Operating Condition Min Max
Operating temperature range -0
o
C +70
o
C
Guaranteed RF performance range -40
o
C +105
o
C
Supply voltage 3.0V 3.6V
RF Transmitter
RF Receiver
Contact Information
Bluepacket Communications Co., Ltd.
5F.-2,No.12,Lane 270,Sec.3,Beishen Rd.,Shenkeng
Township,Taipei County 222, Taiwan (R.O.C )
TEL 886-2-26649168
FAX 886-2-26649166
Document History
Date Revision Reason of change
November 22,
2005 V1.0 Original publication
June 12, 2009 V1.1 Modify
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly
approved by the part responsible for compliance could void the user’s
authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including
interference that may cause undesired operation of the device.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. End users must follow the specific
operating instructions for satisfying RF exposure compliance. This
transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Note: The end product shall has the words
“Contains Transmitter Module FCC ID: _________________________
TM7H4000BEM2