TAKAYA TR3XM-SX01 RFID READER/Writer User Manual TR3XM SX01 EN 100

TAKAYA Corporation RFID READER/Writer TR3XM SX01 EN 100

Contents

manual

User’s Manual TR3XM-SD01 TR3XM-SU01 TR3XM-SN01Manual No.TDR-MNL-SX01-EN-100
Manual No.TDR-MNL-SX01-EN-100 TAKAYA RFID TR3 Series Introduction Thank you for purchasing a TR3XM-SD01／SU01／SN01 RFID READER/WRITER. Be sure to read this manual before using the product. After reading it, store the manual in a convenient place for future reference.
Manual No.TDR-MNL-SX01-EN-100 TAKAYA RFID TR3 Series Regulations and Standards FCC This product is conform to the FCC standards. FCC Rules (Federal Communications Commission) This product complies with Part 15 Subpart B and C of the FCC Rules. FCC ID : MK4TR3XM-SX01 FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Japan Radio Law Equipment using high frequencies: Inductive Reading/Writing Communications Equipment Conforming standards: Inductive Reading/Writing Communications Equipment; Standard: ARIB STD-T82 RoHS is support Restriction of Hazardous Substances Waste Dispose of the Products as industrial waste.
Manual No.TDR-MNL-SX01-EN-100 TAKAYA RFID TR3 Series Safety Precautions The following symbols are used in this manual to indicate precautions that must be observed to ensure safe use of this product. The precautions provided here contain important safety information. Be sure to observe these precautions. The following signal words are used in this manual. Failure to comply with a WARNING may result in serious injury or death. Failure to comply with a CAUTION may result in injury to the operator, or damage to the items involved. Be sure to observe the following precautions to ensure safe use of the Products. Decomposition of this product and cable, repair, remodeling, please strictly prohibited. There is the possibility of fire or electric shock injuries. This product is using the RFID reader writer radio equipment. Therefore, depending on where the applications you use may affect medical equipment. To minimize the impact of medical equipment for use, please observe the following countermeasure. The Japan Automatic Identification Systems Association (JAISA) guidelines are as follows: RFID antennas from implanted cardiac pacemakers or other medical devices please 22cm apart. We recommend that you paste "RFID sticker" at equipment. Be sure to observe the following precautions to ensure safe use of the Products. Installation and storage environment 1. Do not use the Products in sunlight. 2. Do not use the Products in environment of spray of water, oil or chemicals. 3. Do not use the Products in environments with flammable, explosive, or corrosive gasses. 4. Do not use the Products in environment of hot humid. 5. Do not use the Products in environment of vibration or shock. 6. Do not use the Products in environment of condensation. 7. Do not use the Products in environment of around the metal is covered. 8. Do not use the Products in environment of high temperature. 9. Do not use the Products in environment that has a device that generates magnetic field and shock voltage.10. Do not use the Products in unstable place. 11. If there is failure, discontinue use immediately, please contact us or the distributor. Installation 1. Turn off the power before installation or removing. 2. The following effects may not work correctly. ･ Near 13.56MHz radio device ･ Near speakers , Inverter, motor and Plasma Display 3. The communication range may vary due to environment and conditions. ← RFID Sticker
Manual No.TDR-MNL-SX01-EN-100 TAKAYA RFID TR3 Series Contents 1 Product Overview ........................................................................................................ 1 1.1 Features .............................................................................................................................................. 1 2 Names of Parts and Functions ....................................................................................... 3 2.1 TR3XM-SD01 ..................................................................................................................................... 3 2.2 TR3XM-SU01 ..................................................................................................................................... 4 2.3 TR3XM-SN01 ..................................................................................................................................... 5 3 Setting and connection .................................................................................................. 6 3.1 Setting ................................................................................................................................................. 6 3.1.1 DeskTop ........................................................................................................................................... 6 3.1.2 Wall Installation ................................................................................................................................ 6 3.2 Connection .......................................................................................................................................... 7 3.2.1 Attaching the Cable ........................................................................................................................... 7 4 Specifications ............................................................................................................... 8 4.1 TR3XM-SD01 ..................................................................................................................................... 8 4.2 TR3XM-SU01 .................................................................................................................................... 11 4.3 TR3XM-SN01 ................................................................................................................................... 14 5 Accessories ................................................................................................................. 17 5.1 AC Adapter(TR3-PWR-5V-1) ............................................................................................................ 17 5.2 RS232C Cross-cable(CB-232C-2) ...................................................................................................... 18 5.3 USB Cable(GH-USB20/1.8M) ............................................................................................................ 19 5.4 RFID Sticker (SEL41400L) ............................................................................................................... 20 6 Maintenance .............................................................................................................. 21 Revision History ............................................................................................................... 22
Manual No.TDR-MNL-C202-A0-1-EN-100 1 Product Overview 1.1 Features 1 TAKAYA RFID TR3 Series 1 Product Overview 1.1 Features This product uses the 13.56MHz frequency. This product is the electromagnetic induction type non-contact IC can read and write RFID tag data. This Product is the desktop reader choice to support various contactless applications such as electronic ID, payment & public transportation schemes and to interact with NFC-enabled devices. Model Name Host Device Interface TR3XM-SD01 RS232C TR3XM-SU01 USB TR3XM-SN01 TCP/IP Antenna TR3-A202CPU Memory RF-ASIC TR3-C302(READER/WRITER Module) Load Settings Save Settings Interface Module Tags Host Device Interface RS-232C、LAN(TCP/IP)、USB Communications UART(CMOS Level) TR3XM-SD01/TR3XM-SU01/TR3XM-SN01 Block Diagram LED/ BUZZER Host Device Interface
Manual No.TDR-MNL-C202-A0-1-EN-100 1 Product Overview 1.1 Features 2 TAKAYA RFID TR3 Series ■ Conform to international standards ISO/IEC15693 and ISO/IEC18000-3(Mode1, 3) ISO/IEC14443 TypeA ISO/IEC14443 TypeB ISO/IEC18052(Passive Mode), FeliCa ■ Software  TR3-series common communication protocol  Software Development Kit ■ Useful  Continuous inventory mode UID of the tag automatically sends Host Device.  RDLoop mode UID or User Data of the tag automatically sends Host Device. For more information please refer to the TR3-PROTOCOL manual. ■ Environmentally EU RoHS(2002/95/EC) Support
Manual No.TDR-MNL-C202-A0-1-EN-100 2 Names of Parts and Functions 2.1 TR3XM-SD01 3 TAKAYA RFID TR3 Series 2 Names of Parts and Functions 2.1 TR3XM-SD01 No Name Description ① RFID sticker Specify that the RFID radio waves are radiated. ② FCC ID sticker Production numbers, will be 8-digit serial number. ③ Connector Connect the RS-232C cable. ④ DC Jack DC +5V input. ⑤ Rubber leg 4pcs ⑥ Buzzer Sounds according to settings. ⑦ LED Displays the status of this product. ⑧ Cable hook Hook the AC adapter cable that comes with. ⑨ Screw holes M4 holes Model Name Serial number：＊＊＊＊＊＊＊＊(F) ① ② ④ ⑤⑥ ⑧ ⑨ ⑦③
Manual No.TDR-MNL-C202-A0-1-EN-100 2 Names of Parts and Functions 2.2 TR3XM-SU01 4 TAKAYA RFID TR3 Series 2.2 TR3XM-SU01 No Name Description ① RFID sticker Specify that the RFID radio waves are radiated. ② FCC ID sticker Production numbers, will be 8-digit serial number. ③ Connector Connect the USB cable. ④ Rubber leg 4pcs ⑤ Buzzer Sounds according to settings. ⑥ LED Displays the status of this product. ⑦ Screw holes M4 holes Model Name Serial number：＊＊＊＊＊＊＊＊(F) ① ② ③ ④⑥⑤ ⑦
Manual No.TDR-MNL-C202-A0-1-EN-100 2 Names of Parts and Functions 2.3 TR3XM-SN01 5 TAKAYA RFID TR3 Series 2.3 TR3XM-SN01 No Name Description ① RFID sticker Specify that the RFID radio waves are radiated. ② FCC ID sticker Production numbers, will be 8-digit serial number. ③ Connector Connect the TCP/IP cable. ④ DC Jack DC +5V input. ⑤ Rubber leg 4pcs ⑥ Buzzer Sounds according to settings. ⑦ LED Displays the status of this product. ⑧ Cable hook Hook the AC adapter cable that comes with. ⑨ Screw holes M4 holes ⑩ Reset switch ⑪ State switch Selection of User setting or Default is made. Model Name Serial number：＊＊＊＊＊＊＊＊(F) ① ③ ⑥ ② ④ ⑤⑨ ⑦ ⑧ ⑩ ⑪
Manual No.TDR-MNL-C202-A0-1-EN-100 3 Setting and connection 3.1 Setting 6 TAKAYA RFID TR3 Series 3 Setting and connection 3.1 Setting 3.1.1 DeskTop 3.1.2 Wall Installation M4 ScrewWall
Manual No.TDR-MNL-C202-A0-1-EN-100 3 Setting and connection 3.2 Connection 7 TAKAYA RFID TR3 Series 3.2 Connection This product connects with Host Device with the cable. 3.2.1 Attaching the Cable Model Name Cable TR3XM-SD01 RS232C Cable TR3XM-SU01 USB Cable TR3XM-SN01 LAN Cable
Manual No.TDR-MNL-C202-A0-1-EN-100 4 Specifications 4.1 TR3XM-SD01 8 TAKAYA RFID TR3 Series 4 Specifications 4.1 TR3XM-SD01 Specifications Item Parameter Applicable Standards Japan Radio Law ARIB STD-T82 FCC FCC Part 15 Subpart B,C FCC ID : MK4TR3XM-SX01 RoHS EU RoHS(2002/95/EC) Supports Radio Frequency Carrier frequency 13.56MHz ±50ppm(Ta=25℃) or less Antenna Resonant frequency 13.56MHz ±40kHz(Ta=25℃) Transmit power or power range 10～200mW ± 20%(Ta=25℃, VCC=5.0V) Standards ISO/IEC 15693、ISO/IEC18000-3(Mode1、Mode3) ISO/IEC 14443A、ISO/IEC 14443B、ISO/IEC 18092（FeliCa）Tags Tag-it HF-I, my-d, I･CODE SLI, MB89R118 Mifare Ultralight, FeliCa Data rate ・ISO/IEC 15693,ISO/IEC18000-3(Mode1) Speed Data rate Product⇒Tag 1/4 26.48kbps 1/256 1.65kbps Tag⇒Product 26.69kbps ・ISO/IEC18000-3(Mode3) Parameter Product⇒Tag 26.7kbps～100kbps Tag⇒Product 53kbps ・ISO/IEC 14443A, ISO/IEC 14443B 106 kbps ・ISO/IEC 18092(Passive Mode) 212kbps Modulation ・ISO/IEC 15693,ISO/IEC18000-3(Mode1) Parameter Product⇒Tag ASK 10% / ASK 100% Tag⇒Product ASK ・ISO/IEC18000-3(Mode3) Parameter Product⇒Tag ASK 10% Tag⇒Product ASK ・ISO/IEC 14443A Parameter Product⇒Tag ASK 100% Tag⇒Product ASK ・ISO/IEC 14443B ・ISO/IEC 18092(Passive Mode) Parameter Product⇒Tag ASK 10% Tag⇒Product ASK ※1：Tag-it HF-I is a registered trademark of Texas Instruments Incorporated. my-d is a registered trademark of Infineon Technologies AG. I･CODE SLI and MIFARE UltraLight are a registered trademark of NXP Semiconductors. FeliCa is a registered trademark of Sony Corporation. MB89R118 is a registered trademark of FUJITSU Japan.
Manual No.TDR-MNL-C202-A0-1-EN-100 4 Specifications 4.1 TR3XM-SD01 9 TAKAYA RFID TR3 Series Specifications Item Parameter Communication distance Standards Communication distance ISO/IEC 15693 ISO/ISC 18000-3 (Mode1) 10cm ISO/ISC 18000-3 (Mode3) 8cm ISO/ISC 14443A 5.5cm ISO/ISC 14444B 1cm ISO/ISC 18092 (Passive Mode) 3cm (Communication distance depends on the environment.) Anti-collision Standards Anti-collision ISO/IEC 15693 ISO/ISC 18000-3 (Mode1) YES ISO/ISC 18000-3 (Mode3) YES ISO/ISC 14443A No ISO/ISC 14444B No ISO/ISC 18092 (Passive Mode) No Control Host Interface RS-232C Item Parameter Speed 9600bps 19200bps(※2) 38400bps Data bits 8 Parity None Stop bit 1 Flow control None LED 3 LED (red/green/blue) BUZZER 1 BUZZER Connector RS-232C Connector D-SUB 9Pin Pin assignment Pin No. Symbol Function 1 NC Not Connected 2 Rx Received data signal 3 Tx Transmitted data signal 4 NC Not Connected 5 GND GND 6 NC Not Connected 7 NC Not Connected 8 NC Not Connected 9 NC Not Connected DC JACK EIAJ TYPEⅡ(CENTER PLUS) ※2：initialization
Manual No.TDR-MNL-C202-A0-1-EN-100 4 Specifications 4.1 TR3XM-SD01 10 TAKAYA RFID TR3 Series Specifications Item Parameter Mechanical data Dimensions (W x D x H) 140 x 110 x 38.5mm (Protrusions except) Weight approx. 270g Installation M4 Screw Screw is not included. Electrical data Power Supply Voltage ：5V±10% Current consumption ：approx. 170mA Carrier off ：approx. 53mA Power down mode ：approx. 44mA Consumption ：max 1.4W Ambient Conditions Temperature Operating range 0 to 40 degree Humidity Operating range 30 to 80%RH Temperature Storage range 0 to 55 degree Humidity Storage range 30 to 80%RH Accessories AC Adaptor TR3-PWR-5V-1 RS232C Cross-cable CB-232C-2 RFID Sticker SEL41400L 1 sheet CD-ROM CDROM-TR3MNL
Manual No.TDR-MNL-C202-A0-1-EN-100 4 Specifications 4.2 TR3XM-SU01 11 TAKAYA RFID TR3 Series 4.2 TR3XM-SU01 Specifications Item Parameter Applicable Standards Japan Radio Law ARIB STD-T82 FCC FCC Part 15 Subpart B,C FCC ID : MK4TR3XM-SX01 RoHS EU RoHS(2002/95/EC) Supports Radio Frequency Carrier frequency 13.56MHz ±50ppm(Ta=25℃) or less Antenna Resonant frequency 13.56MHz ±40kHz(Ta=25℃) Transmit power or power range 10～200mW ± 20%(Ta=25℃, VCC=5.0V) Standards ISO/IEC 15693、ISO/IEC18000-3(Mode1、Mode3) ISO/IEC 14443A、ISO/IEC 14443B、ISO/IEC 18092（FeliCa）Tags Tag-it HF-I, my-d, I･CODE SLI, MB89R118 Mifare Ultralight, FeliCa Data rate ・ISO/IEC 15693,ISO/IEC18000-3(Mode1) Speed Data rate Product⇒Tag 1/4 26.48kbps 1/256 1.65kbps Tag⇒Product 26.69kbps ・ISO/IEC18000-3(Mode3) Parameter Product⇒Tag 26.7kbps～100kbps Tag⇒Product 53kbps ・ISO/IEC 14443A, ISO/IEC 14443B 106 kbps ・ISO/IEC 18092(Passive Mode) 212kbps Modulation ・ISO/IEC 15693,ISO/IEC18000-3(Mode1) Parameter Product⇒Tag ASK 10% / ASK 100% Tag⇒Product ASK ・ISO/IEC18000-3(Mode3) Parameter Product⇒Tag ASK 10% Tag⇒Product ASK ・ISO/IEC 14443A Parameter Product⇒Tag ASK 100% Tag⇒Product ASK ・ISO/IEC 14443B ・ISO/IEC 18092(Passive Mode) Parameter Product⇒Tag ASK 10% Tag⇒Product ASK ※1：Tag-it HF-I is a registered trademark of Texas Instruments Incorporated. my-d is a registered trademark of Infineon Technologies AG. I･CODE SLI and MIFARE UltraLight are a registered trademark of NXP Semiconductors. FeliCa is a registered trademark of Sony Corporation. MB89R118 is a registered trademark of FUJITSU Japan.
Manual No.TDR-MNL-C202-A0-1-EN-100 4 Specifications 4.2 TR3XM-SU01 12 TAKAYA RFID TR3 Series Specifications Item Parameter Communication distance Standards Communication distance ISO/IEC 15693 ISO/ISC 18000-3 (Mode1) 10cm ISO/ISC 18000-3 (Mode3) 8cm ISO/ISC 14443A 5.5cm ISO/ISC 14444B 1cm ISO/ISC 18092 (Passive Mode) 3cm (Communication distance depends on the environment.) Anti-collision Standards Anti-collision ISO/IEC 15693 ISO/ISC 18000-3 (Mode1) YES ISO/ISC 18000-3 (Mode3) YES ISO/ISC 14443A No ISO/ISC 14444B No ISO/ISC 18092 (Passive Mode) No Control Platform Windows2000, Windows XP, Windows Vista, Windows 7 Host Interface USB2.0/1.1(Virtual COM Port) Item Parameter Speed 9600bps 19200bps(※2) 38400bps Data bits 8 Parity None Stop bit 1 Flow control None LED 3 LED (red/green/ blue) BUZZER 1 BUZZER Connector USB Connector USB B(Receptacle) Pin assignment Pin No. Symbol Function 1 Vbus POWER 2 D- data signal 3 D+ data signal 4 GND GND ※2：initialization
Manual No.TDR-MNL-C202-A0-1-EN-100 4 Specifications 4.2 TR3XM-SU01 13 TAKAYA RFID TR3 Series Specifications Item Parameter Mechanical data Dimensions (W x D x H) 140 x 110 x 38.5mm (Protrusions except) Weight approx. 270g Installation M4 Screw Screw is not included. Electrical data Power Supply Voltage ：5V±10% Current consumption ：approx. 180mA Carrier off ：approx. 61mA Power down mode ：approx. 70mA Consumption ：max 1.4W Ambient Conditions Temperature Operating range 0 to 55 degree Humidity Operating range 30 to 80%RH Temperature Storage range 0 to 55 degree Humidity Storage range 30 to 80%RH Accessories USB cable GH-USB20/1.8M RFID Sticker SEL41400L 1 sheet CD-ROM CDROM-TR3MNL
Manual No.TDR-MNL-C202-A0-1-EN-100 4 Specifications 4.3 TR3XM-SN01 14 TAKAYA RFID TR3 Series 4.3 TR3XM-SN01 Specifications Item Parameter Applicable Standards Japan Radio Law ARIB STD-T82 FCC FCC Part 15 Subpart B,C FCC ID : MK4TR3XM-SX01 RoHS EU RoHS(2002/95/EC) Supports Radio Frequency Carrier frequency 13.56MHz ±50ppm(Ta=25℃) or less Antenna Resonant frequency 13.56MHz ±40kHz(Ta=25℃) Transmit power or power range 10～200mW ± 20%(Ta=25℃, VCC=5.0V) Standards ISO/IEC 15693、ISO/IEC18000-3(Mode1、Mode3) ISO/IEC 14443A、ISO/IEC 14443B、ISO/IEC 18092（FeliCa）Tags Tag-it HF-I, my-d, I･CODE SLI, MB89R118 Mifare Ultralight, FeliCa Data rate ・ISO/IEC 15693,ISO/IEC18000-3(Mode1) Speed Data rate Product⇒Tag 1/4 26.48kbps 1/256 1.65kbps Tag⇒Product 26.69kbps ・ISO/IEC18000-3(Mode3) Parameter Product⇒Tag 26.7kbps～100kbps Tag⇒Product 53kbps ・ISO/IEC 14443A, ISO/IEC 14443B 106 kbps ・ISO/IEC 18092(Passive Mode) 212kbps Modulation ・ISO/IEC 15693,ISO/IEC18000-3(Mode1) Parameter Product⇒Tag ASK 10% / ASK 100% Tag⇒Product ASK ・ISO/IEC18000-3(Mode3) Parameter Product⇒Tag ASK 10% Tag⇒Product ASK ・ISO/IEC 14443A Parameter Product⇒Tag ASK 100% Tag⇒Product ASK ・ISO/IEC 14443B ・ISO/IEC 18092(Passive Mode) Parameter Product⇒Tag ASK 10% Tag⇒Product ASK ※1：Tag-it HF-I is a registered trademark of Texas Instruments Incorporated. my-d is a registered trademark of Infineon Technologies AG. I･CODE SLI and MIFARE UltraLight are a registered trademark of NXP Semiconductors. FeliCa is a registered trademark of Sony Corporation. MB89R118 is a registered trademark of FUJITSU Japan.
Manual No.TDR-MNL-C202-A0-1-EN-100 4 Specifications 4.3 TR3XM-SN01 15 TAKAYA RFID TR3 Series Specifications Item Parameter Communication distance Standards Communication distance ISO/IEC 15693 ISO/ISC 18000-3 (Mode1) 10cm ISO/ISC 18000-3 (Mode3) 8cm ISO/ISC 14443A 5.5cm ISO/ISC 14444B 1cm ISO/ISC 18092 (Passive Mode) 3cm (Communication distance depends on the environment.) Anti-collision Standards Anti-collision ISO/IEC 15693 ISO/ISC 18000-3 (Mode1) YES ISO/ISC 18000-3 (Mode3) YES ISO/ISC 14443A No ISO/ISC 14444B No ISO/ISC 18092 (Passive Mode) No Control Host Interface Ethernet Item Parameter Compliance IEEE802.3 10BASE-T/100BASE-TX Data transfer length MAX 256 Byte/１Packet MAC Address Connection One Connection At the same time Supported protocols ARP、ICMP、TCP/IP、TELNET(Only Configure) Routing One Static Route LED 3 LED (red/green/ blue) BUZZER 1 BUZZER Connector TCP/IP (Ethernet) Connector RJ-45 DC JACK EIAJ TYPEⅡ(CENTER PLUS) ※2：initialization 00-03-D1-XX-XX-XX Product ID Vender ID(TAKAYA CORP.)
Manual No.TDR-MNL-C202-A0-1-EN-100 4 Specifications 4.3 TR3XM-SN01 16 TAKAYA RFID TR3 Series Specifications Item Parameter Mechanical data Dimensions (W x D x H) 140 x 110 x 38.5mm (Protrusions except) Weight approx. 270g Installation M4 Screw Screw is not included. Electrical data Power Supply Voltage ：5V±10% Current consumption ：approx. 380mA Carrier off ：approx. 240mA Power down mode ：approx. 230mA Consumption ：max 2.5W Ambient Conditions Temperature Operating range 0 to 40 degree Humidity Operating range 30 to 80%RH Temperature Storage range 0 to 55 degree Humidity Storage range 30 to 80%RH Accessories AC Adaptor TR3-PWR-5V-1 RFID Sticker SEL41400L 1 sheet CD-ROM CDROM-TR3MNL
Manual No.TDR-MNL-C202-A0-1-EN-100 5 Accessories 5.1 AC Adapter(TR3-PWR-5V-1) 17 TAKAYA RFID TR3 Series 5 Accessories 5.1 AC Adapter(TR3-PWR-5V-1) ■ Specifications Specifications Item Parameter Applicable Standards EMI VCCI CLASS B, FCC class B, CISPR 22 class B COMPLY SAFETY STANDARDS UL60950-1, PSE RoHS EU RoHS(2002/95/EC) Support AC INPUT VOLTAGE AC100V to AC240V FREQUENCY 50 to 60Hz DC OUTPUT DC OUTPUT VOLTAGE RANGE DC5.0V±5% LOAD CURRENT 2.0A OUTPUT CENTER PLUS PLUG TYPE EIAJ TYPE II Mechanical data Wight approx. 110g Dimensions 60(W) x 44(D) x 26.5(H)mm (Cords are not included)Cable length approx. 1800mm Ambient Conditions Temperature Operating range 0 to 40 degree Humidity Operatingrange 5 to 95%RH Temperature Storage range -20 to 65 degree Humidity Storage range 5 to 95%RH ■ Dimension Unit：mm ( )is Recommended Dimension
Manual No.TDR-MNL-C202-A0-1-EN-100 5 Accessories 5.2 RS232C Cross-cable(CB-232C-2) 18 TAKAYA RFID TR3 Series 5.2 RS232C Cross-cable(CB-232C-2) ■ Specifications Specifications Parameter RoHS EU RoHS(2002/95/EC) Support Connector D-sub 9Pin screw Inch screw Cable length approx. 1.8m Connection Cross-cable ■ Dimension (1800) Unit：mm ( )is Recommended Dimension
Manual No.TDR-MNL-C202-A0-1-EN-100 5 Accessories 5.3 USB Cable(GH-USB20/1.8M) 19 TAKAYA RFID TR3 Series 5.3 USB Cable(GH-USB20/1.8M) ■ Specifications Specifications Parameter RoHS EU RoHS(2002/95/EC) Support Connector USB(A)-USB(B) Cable length approx. 1.8m ■ Dimension (1800) Unit：mm ( )is Recommended Dimension
Manual No.TDR-MNL-C202-A0-1-EN-100 5 Accessories 5.4 RFID Sticker (SEL41400L) 20 TAKAYA RFID TR3 Series 5.4 RFID Sticker (SEL41400L) 本ステッカは、医療機器装着者に対し、RFID の電波が出ていることを明示するためのものです。 アンテナが装置等に組み込まれる場合、RFID 機器の本体外部からよく見える位置（アンテナ付近）に貼り付けることを推奨しています。 φ18mm
Manual No.TDR-MNL-C202-A0-1-EN-100 21 TAKAYA RFID TR3 Series 6 Maintenance This product is mainly used in electronic components and semiconductors. Therefore, the long-term stable operation, the environment and conditions are expected to defect, as shown below. • Device degradation due to overvoltage and overcurrent. • Device degradation due to high temperature and long-term stress. • Poor contact of the connector and cause deterioration of insulation by moisture or dust. • Connector corrosion by corrosive gases. In order to use this product at its best, please conduct routine or periodic inspections. Item Maintenance Criteria Ambient conditions Temperature Temperature Operating range 0 to 55 degree Humidity Humidity Operating range 30 to 80%RH Enclosure rating Check the dusty None Corrosive Check the corrosion None Power Input Check the voltage Input Voltage : DC5V±10% Voltage fluctuation Check the Voltage fluctuationAttachment Product Check the Screw Checking and verifying Check the Connector Cable Check the Cable break None Performance Check the Performance Work
Manual No.TDR-MNL-C202-A0-1-EN-100 22 TAKAYA RFID TR3 Series Revision History Revision code Date Revised contents 1.00 2012/03/08 Original production
23 [URL] http://www.takaya.co.jp/ [Mail] rfid@takaya.co.jp

Navigation menu