TCL Technoly Electronics 01 WIFI Module User Manual MT WN713NM SPECIFICATIONS

TCL Technoly Electronics (Huizhou) Co., Ltd. WIFI Module MT WN713NM SPECIFICATIONS

MT-WN713NM_User manual

Specifications of 802.11 b/g/n Wireless USB Module Page 1 of 12 SPECIFICATIONS 802.11 b/g/n Wireless USB Module (USB Host Power Is 3.3V) Ver. 2.0 Date: 10/4/2012
Specifications of 802.11 b/g/n Wireless USB Module Page 2 of 12 Contents Device Overall Description ....................................................... 3 Features ..................................................................................... 3 Specification Compliance .......................................................... 3 Block Diagram .......................................................................... 4 Channel Assignment .................................................................. 4 Security ...................................................................................... 5 Certification ............................................................................... 5 Software & OS support .............................................................. 5 Operating Conditions ................................................................ 5 RF Characteristics .................................................................... 6 Mechanical Drawing ................................................................. 7 Antenna Connector .................................................................... 8 LED Indication .......................................................................... 8
Specifications of 802.11 b/g/n Wireless USB Module Page 3 of 12 Device Overall Description The WN713NM is designed to provide wireless LAN function on a small form factor with USB interface. The wireless LAN function is based on Ralink RT5370 MAC/BBP/RF controller and high gain power amplifier, fully comply with current draft IEEE 802.11n and IEEE 802.11 b/g standards. Features z Ralink RT5370 MAC/BBP/RF Controller z 1T1R Modes z 11b: 1,2,5.5,11Mbps z 11g: 6,9,12,18,24,36,48,54Mbps z 11n: Legacy and High Throughput Modes, Support 20/40MHz Bandwidth MCS0~7(150Mbps PHY Rate Rate) z Reverse Direction Data Flow and Frame Aggregation z WEP 64/128, WPA, WPA2, TKIP, AES z QoS-WMM, WMM-PS z WPS, PIN, PBC z Multiple BSSID Support z Low Power with Advanced Power Management Specification Compliance z 802.11n Draft3.0 z 802.11b/g z 802.11e z 802.11i z 802.11j z USB2.0
Specifications of 802.11 b/g/n Wireless USB Module Page 4 of 12 Block Diagram RT5370:Highly integrated MAC/BBP and 2.4GHz RF single chip Channel Assignment 2.4GHz Channel Support Channel Frequency FCC (US) IC(CA) ETSI (EU) Japan (JP) 1 2412MHz X X X X 2 2417MHz X X X X 3 2422MHz X X X X 4 2427MHz X X X X 5 2432MHz X X X X 6 2437MHz X X X X 7 2442MHz X X X X 8 2447MHz X X X X 9 2452MHz X X X X 10 2457MHz X X X X 11 2462MHz X X X X 12 2467MHz X X 13 2472MHz X X 14 2484MHz X KEY: US = United States, CA = Canada, EU = European Countries (except France and Spain) ,JP = Japan Many countries and region are currently revising the channel assignment. X = Supported
Specifications of 802.11 b/g/n Wireless USB Module Page 5 of 12 Security z Complete Security Features - WEP 64/128, WPA, WPA2, 802.1x, and 802.11i z Cisco CCS Compliant Certification ٛ Cisco CCX Software & OS support Operating System Driver Windows 2000 Available Windows XP 32/64 Available Windows Vista 32/64 Available Windows 7 32/64 Available Linux Available MAC OS Available Operating Conditions Voltage Range 5 +/0.3V Operating Temperature Range -10°C - 65°C Storage Temperature Range -10°C - 85°C Relative Humidity during Operating Max. 95% (Non-Condensing) Relative Humidity during Storage Max. 95% (Non-Condensing)
Specifications of 802.11 b/g/n Wireless USB Module Page 6 of 12 RF Characteristics RF Characteristics Minimum Typical Maximum Units PC Interface USB 2.0 Internal Antenna Impedance 50 ohms Operating Temperature Range 0 +65 ℃ Storage Temperature Range -20 +85 ℃ Supply Voltage 4.7 5.0 5.3 V RX Supply Current (11b 11MBps) 140 mA Power Consumption 462 mWatts RX Supply Current (11g 54Mbps) 150 mA Power Consumption 495 mWatts RX Supply Current (11n 150Mbps) 190 mA Power Consumption 627 mWatts TX Supply Current (11b 1MBps) 265 mA Power Consumption 875 mWatts TX Supply Current(11g 6Mbps) 255 mA Power Consumption 842 mWatts TX Supply Current (11n 15Mbps) 245 mA Power Consumption 809 mWatts Radio off Current 40 mA Power Consumption 132 mWatts RX Sensitivity(11b,11Mbps) -86 dBm RX Sensitivity(11g,54Mbps) -71 dBm RX Sensitivity (11n,150Mbps) -63 dBm TX Output Power(11b,11M) 17 dBm TX Output Power(11g,54Mbps) 15 dBm TX Output Power(11n,MCS0) 14 dBm TX Output Power(11n,MCS7) 14 dBm TX Spectral Mask (CCK) PASS TX Spectral Mask (OFDM) PASS TX Spectral Mask (11n,20M) PASS TX Spectral Mask (11n,40M) PASS Preamble Length Long/Short
Specifications of 802.11 b/g/n Wireless USB Module Page 7 of 12 Mechanical Drawing
Specifications of 802.11 b/g/n Wireless USB Module Page 8 of 12 Antenna Connector Connector Vendor Part# Antenna*1 Hirose On Board PCB Antenna Host Interface Pin Definition 1 FAA pin: WLAN RF Disable/Enable 2 Vcc 3 USB Data- 4 USB Data + 5 GND 6 WLAN LED LINK Note: Pin 6 is Low active for WLAN LED Link. Pin 1 is Low voltage to disable RF function LED Indication LED status WLAN card activity LED on Associated, and authenticated but not transmitting or receivingLED Slow Blink Scanning for AP LED Intermittent Blink Activity proportional to transmitting/receiving speed LED off Radio off 65 432 1
Specifications of 802.11 b/g/n Wireless USB Module Page 9 of 12 COMPLIANCES Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. * Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
Specifications of 802.11 b/g/n Wireless USB Module Page 10 of 12 IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The end host device use this module should marked "Contain FCC ID:ZVA01" in the label of the host device.

Navigation menu