TCL Technoly Electronics 01 WIFI Module User Manual MT WN713NM SPECIFICATIONS
TCL Technoly Electronics (Huizhou) Co., Ltd. WIFI Module MT WN713NM SPECIFICATIONS
MT-WN713NM_User manual
Specifications of 802.11 b/g/n Wireless USB Module
Page 1 of 12
SPECIFICATIONS
802.11 b/g/n Wireless USB Module
(USB Host Power Is 3.3V)
Ver. 2.0
Date: 10/4/2012
Specifications of 802.11 b/g/n Wireless USB Module
Page 2 of 12
Contents
Device Overall Description ....................................................... 3
Features ..................................................................................... 3
Specification Compliance .......................................................... 3
Block Diagram .......................................................................... 4
Channel Assignment .................................................................. 4
Security ...................................................................................... 5
Certification ............................................................................... 5
Software & OS support .............................................................. 5
Operating Conditions ................................................................ 5
RF Characteristics .................................................................... 6
Mechanical Drawing ................................................................. 7
Antenna Connector .................................................................... 8
LED Indication .......................................................................... 8
Specifications of 802.11 b/g/n Wireless USB Module
Page 3 of 12
Device Overall Description
The WN713NM is designed to provide wireless LAN function on a small form factor with
USB interface. The wireless LAN function is based on Ralink RT5370 MAC/BBP/RF
controller and high gain power amplifier, fully comply with current draft IEEE 802.11n
and IEEE 802.11 b/g standards.
Features
z Ralink RT5370 MAC/BBP/RF Controller
z 1T1R Modes
z 11b: 1,2,5.5,11Mbps
z 11g: 6,9,12,18,24,36,48,54Mbps
z 11n: Legacy and High Throughput Modes, Support 20/40MHz Bandwidth
MCS0~7(150Mbps PHY Rate Rate)
z Reverse Direction Data Flow and Frame Aggregation
z WEP 64/128, WPA, WPA2, TKIP, AES
z QoS-WMM, WMM-PS
z WPS, PIN, PBC
z Multiple BSSID Support
z Low Power with Advanced Power Management
Specification Compliance
z 802.11n Draft3.0
z 802.11b/g
z 802.11e
z 802.11i
z 802.11j
z USB2.0
Specifications of 802.11 b/g/n Wireless USB Module
Page 4 of 12
Block Diagram
RT5370:Highly integrated MAC/BBP and 2.4GHz RF single chip
Channel Assignment
2.4GHz Channel Support
Channel Frequency FCC (US) IC(CA) ETSI (EU) Japan (JP)
1 2412MHz X X X X
2 2417MHz X X X X
3 2422MHz X X X X
4 2427MHz X X X X
5 2432MHz X X X X
6 2437MHz X X X X
7 2442MHz X X X X
8 2447MHz X X X X
9 2452MHz X X X X
10 2457MHz X X X X
11 2462MHz X X X X
12 2467MHz X X
13 2472MHz X X
14 2484MHz X
KEY:
US = United States, CA = Canada, EU = European Countries (except France and Spain) ,JP = Japan
Many countries and region are currently revising the channel assignment.
X = Supported
Specifications of 802.11 b/g/n Wireless USB Module
Page 5 of 12
Security
z Complete Security Features - WEP 64/128, WPA, WPA2, 802.1x, and 802.11i
z Cisco CCS Compliant
Certification
ٛ Cisco CCX
Software & OS support
Operating System Driver
Windows 2000 Available
Windows XP 32/64 Available
Windows Vista 32/64 Available
Windows 7 32/64 Available
Linux Available
MAC OS Available
Operating Conditions
Voltage Range 5 +/0.3V
Operating Temperature Range -10°C - 65°C
Storage Temperature Range -10°C - 85°C
Relative Humidity during Operating Max. 95% (Non-Condensing)
Relative Humidity during Storage Max. 95% (Non-Condensing)
Specifications of 802.11 b/g/n Wireless USB Module
Page 6 of 12
RF Characteristics
RF Characteristics Minimum Typical Maximum Units
PC Interface USB 2.0
Internal Antenna Impedance 50 ohms
Operating Temperature Range 0 +65 ℃
Storage Temperature Range -20 +85 ℃
Supply Voltage 4.7 5.0 5.3 V
RX Supply Current (11b 11MBps) 140 mA
Power Consumption 462 mWatts
RX Supply Current (11g 54Mbps) 150 mA
Power Consumption 495 mWatts
RX Supply Current (11n 150Mbps) 190 mA
Power Consumption 627 mWatts
TX Supply Current (11b 1MBps) 265 mA
Power Consumption 875 mWatts
TX Supply Current(11g 6Mbps) 255 mA
Power Consumption 842 mWatts
TX Supply Current (11n 15Mbps) 245 mA
Power Consumption 809 mWatts
Radio off Current 40 mA
Power Consumption 132 mWatts
RX Sensitivity(11b,11Mbps) -86 dBm
RX Sensitivity(11g,54Mbps) -71 dBm
RX Sensitivity (11n,150Mbps) -63 dBm
TX Output Power(11b,11M) 17 dBm
TX Output Power(11g,54Mbps) 15 dBm
TX Output Power(11n,MCS0) 14 dBm
TX Output Power(11n,MCS7) 14 dBm
TX Spectral Mask (CCK) PASS
TX Spectral Mask (OFDM) PASS
TX Spectral Mask (11n,20M) PASS
TX Spectral Mask (11n,40M) PASS
Preamble Length Long/Short
Specifications of 802.11 b/g/n Wireless USB Module
Page 7 of 12
Mechanical Drawing
Specifications of 802.11 b/g/n Wireless USB Module
Page 8 of 12
Antenna Connector
Connector Vendor Part#
Antenna*1 Hirose On Board PCB Antenna
Host Interface Pin Definition
1 FAA pin: WLAN RF Disable/Enable
2 Vcc
3 USB Data-
4 USB Data +
5 GND
6 WLAN LED LINK
Note:
Pin 6 is Low active for WLAN LED Link.
Pin 1 is Low voltage to disable RF function
LED Indication
LED status WLAN card activity
LED on Associated, and authenticated but not transmitting or receiving
LED Slow Blink Scanning for AP
LED Intermittent Blink Activity proportional to transmitting/receiving speed
LED off Radio off
6
5
4
3
2
1
Specifications of 802.11 b/g/n Wireless USB Module
Page 9 of 12
COMPLIANCES
Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
Specifications of 802.11 b/g/n Wireless USB Module
Page 10 of 12
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
The end host device use this module should marked "Contain FCC ID:ZVA01"
in the label of the host device.