TCL Technoly Electronics 07 Bluetooth Module User Manual BM90SPKA5MG7 101x
TCL Technoly Electronics (Huizhou) Co., Ltd. Bluetooth Module BM90SPKA5MG7 101x
BM90SPK User Manual
BM90SPKA5MG7 BM90SPKA5MG7 Bluetooth 3.0 EDR Audio Module 5F, No.5, Industry E. Rd. VII, Hsinchu Science Park, Hsinchu city 30077, Taiwan, R.O.C Phone: 886-3-577-8385 Fax: 886-3-577-8501 Version:1.01 6/26/2014 BM90SPKA5MG7 Product Description The ISSC BM90SPKA5MG7 is a highly integrated Bluetooth 3.0 EDR stereo module, designed for high data rate, short-range wireless communication in the 2.4 GHz ISM band. With the build-in ISSC Bluetooth stack and profile, the ISSC BM90SPKA5MG7 provides a low power and ultra-low cost Bluetooth 3.0+EDR solution for multi-speaker applications. Features Main Chip: ISSC IS1690SM Bluetooth 3.0 EDR compliant Max. +4dBm Class 2 output power Receiver Sensitivity: GFSK typical -90dBm, π/4 PSK typical -91dBm, 8DPSK typical -83dBm Piconet and Scatter net support CVSD, A-law, -law CODEC algorithms for voice applications SBC decode for Bluetooth audio streaming Build-in High performance stereo audio codec Microphone input and audio line-in support Build-in audio mux/gain control for line-in audio signal Cap-less/single end headphone driver Audio DAC: 94dB SNR Build in 350mAH Li-ion battery charger HSP, HFP, A2DP, AVRCP 1.5 profiles supported 3.3V operating voltage 4Mb Embedded flash program memory and 32Kb EEPROM 37pins for SMT module Size: 15mm x29mm Build-in PCB Antenna RoHS compliant Version: 1.01 -2- 6/26/2014 BM90SPKA5MG7 Module Pin out Diagram BM90SPKA5MG7 P35 EAN P30 P20 P00 P04 SPKR AOHPM SPKL VDDA MIC1_P MIC1_N MIC_BIAS AIR GND P03 P01 P16 HCI_RXD HCI_TXD P05 P02 P24 LED2 LED1 MFB BK_OUT SY S_PWR 37 36 35 34 33 32 31 30 29 28 27 26 25 24 15 16 17 18 19 20 21 22 23 AIL RST P34 P37 VDD_IO ADAP_IN BAT_IN SK1 GND 10 11 12 13 14 Version: 1.01 -3- 6/26/2014 BM90SPKA5MG7 Pin Definition Pin No. I/O Name Description I/O P35 GPIO, default pull-high input REW button EAN Embedded ROM/External Flash enable H: Embedded; L: External Flash P30 GPIO, default pull-high input Line-in detection, 1: no line-in detected; 0: line-in detected I/O P20 GPIO, default pull-high input System Configuration, H: Application L: Baseband(IBDK Mode) I/O P00 GPIO, default pull-low input. Audio AMP Enable I/O P04 GPIO, default pull-high input NFC AO SPKR AP AOHPM AO SPKL L-channel analog headphone output, for cap-less and single-ended application both 10 AP VDDA Reserve for external cap to fine tune audio frequency response 11 AI MIC1_P Mic 1 mono differential analog positive input 12 AI MIC1_N Mic 1 mono differential analog negative input 13 AP MIC_BIAS 14 AI AIR Stereo analog line in, R-channel 15 AI AIL Stereo analog line in, L-channel 16 I/O RST_N 17 I/O P34 18 I/O P37 19 VDDIO Version: 1.01 R-channel analog headphone output, for cap-less and single-ended application both Headphone common mode output/sense input. Cap-less application only. Microphone biasing voltage System Reset Pin GPIO, default pull-high input NFC_SW GPIO, default pull-high input FWD button VDDIO pin, for calibration only Do not add external power to this pin -4- 6/26/2014 BM90SPKA5MG7 20 ADAP_IN 21 BAT_IN 22 I/O SK1 Default SAR input for battery detection 23 GND Ground 24 25 BK_OUT 26 MFB Multi-Function Push Button key 27 LED1 LED Driver 1 28 LED2 LED Driver 2 29 I/O P24 GPIO, default pull-high input System Configuration, H: Boot Mode 30 I/O P02 GPIO, default pull-high input PLAY/PAUSE button 31 I/O P05 GPIO, default pull-high input Phone button 32 HCI_TXD HCI TX data 33 HXI_RXD HCI RX data 34 I/O P16 GPIO, default pull-high input Volume down button 35 I/O P01 GPIO, default pull-high input Volume up button 36 I/O P03 3rd LED 37 GND Ground. Version: 1.01 Power adaptor input Battery input SYS_PWR System Power Output Buck feedback sense pin -5- 6/26/2014 BM90SPKA5MG7 Electrical Characteristics Absolute Maximum Ratings Rating Operation Temperature Core supply voltage VDD_CORE, VCC_RF, AVDD_SAR, AVDD_PLL Codec supply voltage VDD_AUDIO I/O voltage Supply voltage Min Max Max -40ºC +85ºC ºC 1.7V 1.98V VDD_IO 3.3 BK_VDD 4.3 3V1_VIN BAT_IN 4.3 ADAP_IN 7.7 LED[1:0] Power switch Recommended Operate Condition Symbol Parameter VDD18 Digital core supply voltage SAR ADC supply voltage Min Typical Max Unit 1.8 1.85 1.95 CODEC supply voltage VDDIO I/O supply voltage 2.8 3.3 TOPERATION Operating temperature range -20 +25 +70 ºC Tstg Storage temperature -40 +125 ºC VLDO LDO supply voltage 1.8 3.3 VBAT_IN Supply voltage for Battery_in 3.0 4.2 Version: 1.01 -6- 6/26/2014 BM90SPKA5MG7 Radio Characteristics: Transmitter section for BDR VCC_RF = 1.85V Min Typ Max Temperature = 25ºC Bluetooth Unit specification Maximum RF transmit power 4.0 -6 to 4 dBm RF power variation over temperature ±2 range with compensation enabled dB RF power control range 20 ≥16 dB RF power range control resolution 0.5 20dB bandwidth for modulated carrier 900 ≤1000 KHz ACP F = F0±2MHz -28 ≤-20 dBm F = F0±3MHz -46 ≤-40 dBm F = F0±>3MHz -54 ≤-40 dBm dB Note: F0=2441MHz ∆f1avg maximum modulation 150 165 140<∆f 1avg<175 KHz ∆f2max maximum modulation 140 150 ≥115 KHz ∆f2avg/∆f1avg 0.95 ICFT (abs) Drift rate (abs) ≥0.80 10 75 ≤20 KHz KHz/50u Drift (single slot packet, abs) 12 ≤25 KHz 2nd harmonic content @ Tx= 4dBm -53 ≤-47 dBm 3rd harmonic content @ Tx= 4dBm -55 ≤-47 dBm Version: 1.01 -7- 6/26/2014 BM90SPKA5MG7 Receiver section for BDR Temperature = 25ºC Frequency (GHz) Min Typ 2.402 -90 2.441 -90 2.480 -90 Max Bluetooth specification Unit Sensitivity at 0.1% BER for all basic rate packet types Maximum received signal at 0.1% BER C/I co-channel F= F0+1MHz F= F0-1MHz F= Adjacent channel F0+2MHz selectivity C/I F= F0-2MHz Note: F0=2441MHz F= F0-3MHz F= F0+5MHz F = Fimage Maximum level of intermodulation interferers Version: 1.01 -8- ≤-70 dBm -10 ≥-20 dBm ≤11 dB -7 ≤0 dB -7 ≤0 dB -36 ≤-30 dB -22 ≤-9 dB -24 ≤-20 dB -50 ≤-40 dB -22 ≤-9 dB -38 ≥-39 dB 6/26/2014 BM90SPKA5MG7 Transmitter Section for EDR Temperature = 25ºC Min Typ Max Bluetooth Unit specification Relative transmit power -1.6 |ωo| carrier frequency stability dB ≤10 for all freq. error π/4 DQPSK max -4 to 1 blocks |ωi| initial freq. ≤75 for all 10 blocks KHz KHz error |ωo+ωi| block freq. ≤75 for all 10 blocks error |ωo| ≤10 for all freq. error blocks |ωi| 8DPSK max carrier initial freq. frequency stability error KHz KHz ≤75 for all 10 blocks |ωo+ωi| block freq. ≤75 for all 10 blocks KHz KHz error RMS DEVM ≤20 99% DEVM Pass ≤30 ≤35 π/4 DQPSK modulation accuracy @ Tx= 2dBm Peak DEVM 25 RMS DEVM ≤13 99% DEVM Pass ≤20 ≤25 8DQPSK modulation accuracy @ Tx= 2dBm Peak DEVM Version: 1.01 20 -9- 6/26/2014 BM90SPKA5MG7 In-band spurious emissions Note: F0=2441MHz F > F0+3MHz <-54 ≤-40 dBm F = F0-3MHz -46 ≤-40 dBm F = F0-2MHz -28 ≤-20 dBm F = F0-1MHz -30 ≤-26 dBm F = F0+1MHz -30 ≤-26 dBm F = F0+2MHz -28 ≤-20 dBm F = F0+3MHz -46 ≤-40 dBm 100 ≥99 EDR differential phase encoding Version: 1.01 - 10 - 6/26/2014 BM90SPKA5MG7 Receiver Section for EDR Frequency Temperature = 25ºC (GHz) 2.402 2.441 Sensitivity at 0.01% BER Bluetooth Modulation 2.480 Min Typ Max Unit specification π/4 DQPSK π/4 DQPSK π/4 -91 -91 ≤-70 dBm ≤-70 dBm -91 DQPSK 2.402 8DPSK -83 2.441 8DPSK -83 2.480 8DPSK -83 π/4 Maximum received signal at 0.1% DQPSK -10 ≥-20 dBm BER 8DPSK π/4 C/I co-channel at 0.1% BER DQPSK 8DPSK π/4 F = F0+1MHz DQPSK 8DPSK π/4 Adjacent channel selectivity C/I F = F0-1MHz 8DPSK π/4 Note: F0=2441MHz DQPSK F = F0+2MHz DQPSK 8DPSK -10 ≥-20 ≤13 dB ≤21 dB -14 ≤0 dB -8 ≤5 dB -13 ≤0 dB -8 ≤5 dB -38 ≤-30 dB -34 ≤-25 dB -21 ≤-7 dB -21 ≤0 dB π/4 F = F0-2MHz DQPSK 8DPSK Version: 1.01 - 11 - 6/26/2014 BM90SPKA5MG7 π/4 F = F0-3MHz 8DPSK π/4 F = F0+5MHz DQPSK 8DPSK π/4 F = Fimage DQPSK 8DPSK Version: 1.01 -27 ≤-20 dB -20 ≤-13 dB -52 ≤-40 dB -45 ≤-33 dB -21 ≤-7 dB -21 ≤0 dB DQPSK - 12 - 6/26/2014 BM90SPKA5MG7 Audio Codec: ADC (MIC PATH/Line-in path) Test Condition: T= 25oC, VDD=2.8V, 1KHz sine wave input, Bandwidth = 20~20KHz Parameter Input full-scale Condition Min. Full scale (line-in) Resolution Max. Unit 2.2 Vpp 16 Input Sampling Rate SNR Typ. fin=1KHz B/W=20~20KHz bits 48 8KHz 85 16KHz 85 32KHz 85 44.1KHz 85 48KHz 85 kHz A-weighted THD+N < 1% 150mVpp input SNR A-weighted 1KHz@full scale, dB 75 dB 0.04 0.01 20 dB Microphone boost enable THD+N (Mic input) @30mVrms input THD+N (line input) Mic Boost Gain Digital Gain -54 Analog Gain 4.85 dB 26 dB Digital Gain Step dB Analog Gain Step 1.7 dB Input impedance Input impedance (microphone mode) Input capacitance 10 KΩ 20 pF 3.0 Analog supply voltage 1.8 (AVDD) Version: 1.01 - 13 - 2.8 6/26/2014 BM90SPKA5MG7 Audio Codec: DAC (SPEAKER path) Test Condition: T= 25oC, VDD=2.8V, 1KHz sine wave input, Bandwidth= 20~20KHz Parameter Condition Output Level Full scale Min. Max. 2.1 Resolution 16 Output Sampling Rate SNR Typ. fin=1KHz Unit Vpp bits 48 KHz 8KHz 94 dB 16KHz 94 dB 32KHz 94 dB 44.1KHz 94 dB 48KHz 94 dB RL=16Ohm 35 mW RL=32Ohm 17 mW B/W=20~20KHz A-weighted THD+N < 0.01% 0dBFS signal Load=100KΩ Max Output Power THD+N 16Ohm load 0.05 100KΩ load 0.01 4.85 dB Digital Gain -54 Digital Gain Resolution Analog Gain -28 Analog Gain step Output resistance RL Output capacitance Cp Crosstalk between L vs. R, measured at channels -10dBFS@1KHz input Analog supply voltage 1.8 (AVDD) Version: 1.01 - 14 - dB dB dB 16 Ohm 500 pF -90 -80 dB 2.8 3.0 6/26/2014 BM90SPKA5MG7 Battery Charger Charging Mode (BAT_IN rising to 4.2V) Min Operation Temperature Typ Max Unit -10 55 ℃ 4.5 Input Voltage (Vin) Note: It needs more time to get battery fully charged when Vin=4.5V Battery trickle charge current 0.1C mA (BAT_IN < trickle charge voltage threshold) Trickle charge voltage threshold Maximum battery Headroom > 0.7V 350 mA charge current Headroom = 0.3V 150 mA Minimum battery Headroom > 0.7V mA charge current Headroom = 0.3V mA 10 100 mV 0.25C mA Battery charge termination current, % of fast charge current Battery recharge hysteresis (Note1) Battery recharge current (Note2) Note: C Battery capacity Note1:When charging complete and the adapter is still in, the battery voltage will slowly drop down. When the voltage drop is larger than 100mV from the full voltage, the re-charging cycle will start. Note2:If the battery voltage during plug in is larger than 4V, the charging current will be limited to 0.25C to avoid the battery voltage overshoot. Version: 1.01 - 15 - 6/26/2014 BM90SPKA5MG7 Clock Parameters MIN TYP MAX Unit Crystal Frequency 16 MHz Frequency Tolerance 20 ppm Operating Temperature -20 70 Trimming Capacitance 6.4 pF Trimming Step Size 0.2 pF Digital GPIO Parameters MIN TYP MAX Unit 3.6 Input Voltage 2.7 VIH (Input High Voltage) 2.0 Vdd VIL (Input Low Voltage) 0.8 Input Reference Resistor RPU (Pull-Up Resistor) 50K Ohm RPD (Pull-Down Resistor) 50K Ohm Output Voltage VOH (Output High Voltage) 2.4 Vdd VOL (Output Low Voltage) 0.4 Version: 1.01 - 16 - 6/26/2014 BM90SPKA5MG7 Current Consumption Flash version Single Mode Test Condition: T= 25oC, BAT_IN=4.0V, with flash code, codec without loading Normal Operation Min Off mode Typ Max Unit 5.6 uA mA Link mode 0.9 mA SCO link 23.5 mA A2DP link 26.9 mA Standby mode Twin Mode Test Condition: T= 25oC, BAT_IN=4.0V, with flash code, codec without loading Normal Operation Min Typ Max Unit Off mode 5.6 uA Standby mode 1.3 mA Link mode 1.1 mA SCO link 25.8 mA A2DP link 34 mA Version: 1.01 - 17 - 6/26/2014 BM90SPKA5MG7 Antenna performance Parameters MIN Antenna gain MAX 1.76 Efficiency Version: 1.01 TYP 70 - 18 - Unit dBi 80 6/26/2014 BM90SPKA5MG7 Outline Dimension (Module Foot print) Version: 1.01 - 19 - 6/26/2014 BM90SPKA5MG7 Reflow profile Version: 1.01 - 20 - 6/26/2014 BM90SPKA5MG7 QR code label information Label Size:15±1.5 mm *6±1.5 mm ①Device Name: BMxxxxxxxxxx (12digits) ②MAC ID: xxxxxxxxxxxx (12 digits) ③Date Code: xxxx (4 digits) ④Customer Code No: xxxxxx (6 digits) Customer Part No example: BM90SPKA5MG7-C58096 ↓ Device Name ↓ Customer code no. Module Weight (Test condition: module with QR label) 0.95g ± 10% Version: 1.01 - 21 - 6/26/2014 BM90SPKA5MG7 Storage standard 1. Calculated shelf life in sealed bag: 12 months at < 40 ℃ and <90% relative humidity (RH) 2. After bag is opened, devices that will be subjected to reflow solder or other high temperature process must be Mounted within 168 hours of factory conditions <30℃/60% RH Version: 1.01 - 22 - 6/26/2014 BM90SPKA5MG7 Ordering Information Module Device Size Shipment Method 29*15 mm Tray Order Number BM90SPKA5MG7 Bluetooth 3.0 EDR Wireless Speaker Module Note: Minimum Order Quantity is 630pcs Tray. Version: 1.01 - 23 - 6/26/2014 BM90SPKA5MG7 Packing Information Tray Dimensions Version: 1.01 - 24 - 6/26/2014 BM90SPKA5MG7 Packing Method Inner box: Q’ty (630 Pcs) Dimensions: 36*16*9.5 cm Bar Code Label Example P/N: Part No.(device name) C/N: Customer Part No.(Part no. - customer code no.) Lot No: Lot ID Q’ty: box or Carton Module’s Q’ty Carton: Q’ty (3780 Pcs) Dimensions: 38*35*30 cm Version: 1.01 - 25 - 6/26/2014 How w to fix the BT model BM90SPK too SRS‐X11 1、 BM90SPK BT M Model contains PCB Anten nna; 2、 The T gain of PCCB Antenna iss about 1.76d dBi; 1、Every moodel has 37 pin; 2、Fix the BTT model to SR RS‐X11 main board by its 337 pin; 3、Every pinn is fixed on the main boarrd by tin. 1、Main bboard is fixed to SRS‐X11 by b the Screw SRS‐‐X11 FCC C Statement Channges or modiifications not expressly appproved by thee party respon nsible for com mpliance cou uld voidd the user's auuthority to operate the equiipment CC Rules. Op Thiss device compplies with Parrt 15 of the FC peration is su ubject to the ffollowing two condditions: (1) thhis device may y not cause hharmful interfference, and (2) ( this devicee must acceptt any interference received, inclluding interfeerence that may m cause und desired operattion. IC S Statement Thiss device compplies with Ind dustry Canadaa licence-exempt RSS stan ndard(s). Opeeration is subjject to thhe following two t condition ns: (1) this deevice may nott cause interfeerence, and (22) this devicee mustt accept any interference, including intterference thaat may cause undesired opeeration of thee device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. The end host device should bear the label which indicate "Contains FCC ID:ZVA07" or "Contains IC: 9976A-07".
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : Jim.issc Create Date : 2014:06:26 09:09:25+08:00 Modify Date : 2014:11:12 19:03:59+08:00 XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Format : application/pdf Creator : Jim.issc Title : Microsoft Word - BM90SPKA5MG7_101.docx Creator Tool : Microsoft Word - BM90SPKA5MG7_101.docx Metadata Date : 2014:11:12 19:03:59+08:00 Producer : doPDF Ver 7.1 Build 341 (Windows 7 Business Edition - Version: 6.1.7600 (x86)) Document ID : uuid:a97818df-bdc1-4bd7-8e8f-b1f8a3a18215 Instance ID : uuid:96b3b20b-7513-46ce-af77-cb4eda48187e Page Layout : OneColumn Page Mode : UseNone Page Count : 28EXIF Metadata provided by EXIF.tools