TECNO MOBILE CA6 Mobile Phone User Manual Sanjeev

TECNO MOBILE LIMITED Mobile Phone Sanjeev

User Manual

ExplosionExplosion diagramdiagram specificationspecification1LCM Assembly2Front Housing Assembly3Sidkey FPC4Front housing rubber5Card Slot seal foam6Receiver Deco7Receiver seal foam8Receiver9Front CAM seal foam10LED rubber11PS rubber12Front Camera13Back Camera14Card Holder15Audio jack rubber16Main PCB17Front CAM Conductive Fabric18Shield Graphite Film19Coaxial Cable 220Back Flash Seal Foam21Fingerprint Frame22Screw23Back CAM lens24Fingerprint Conductive Foam25Fingerprint Module26LCM Connector Pressed Steel27LCM BTB Mylar28Battery
29Battery Cover Assembly30Screw31Speaker32Main Mic Rubber33Motor34Coaxial cable 135Main FPC36Usb Rubber37PCBA38Speaker FPC
KnowKnow youryour phonephoneVolume keyPower keyFront camera
SIM/SD card installation1. Power off mobile.2. Refer to the following picture for SIM / SD card installation.
ChargingCharging thethe phonephoneYou can charge your device using a charger or by connecting itto the computer using a USB cable (comes with the phone).1. Please remind the front and back of the plug.2. Use only TECNO charger and cables. Other chargers or cablesmay damage the device or your device. This will invalidateyour phone warranty.
FCC CautionLabelling requirements.This device complies with part 15 of the FCC Rules. Operation is subjectto the condition that this device does not cause harmful interference.Information to user.Any Changes or modifications not expressly approved by the partyresponsible for compliance could void the user's authority to operate theequipment.Information to the user.Note: This equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipmentgenerates uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may causeharmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or moreof the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help.Specific Absorption Rate (SAR) information:This Mobile phone meets the government's requirements for exposure toradio waves. The guidelines are based on standards that were developedby independent scientific organizations through periodic and thoroughevaluation of scientific studies. The standards include a substantial safetymargin designed to assure the safety of all persons regardless of age orhealth.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is1.6 W/kg averaged over one gram of tissue. Device types: CA6(FCC ID:2ADYY-CA6 ) has also been tested against this SAR limit. The highestSAR value reported under this standard during product certification foruse at the ear is 0.37 W/kg and when properly worn on the body is 1.02W/kg. This device was tested for typical body-worn operations with theback of the handset kept 10mm from the body. To maintain compliancewith FCC RF exposure requirements, use accessories that maintain a10mm separation distance between the user's body and the back of thehandset. The use of belt clips, holsters and similar accessories should notcontain metallic components in its assembly. The use of accessories thatdo not satisfy these requirements may not comply with FCC RF exposurerequirements, and should be avoided.Body-worn OperationThis device was tested for typical body-worn operations. To comply withRF exposure requirements, a minimum separation distance of 1.0 cmmust be maintained between the user’s body and the handset, includingthe antenna. Third-party belt-clips, holsters, and similar accessories usedby this device should not contain any metallic components. Body-wornaccessories that do not meet these requirements may not comply with RFexposure requirements and should be avoided. Use only the supplied oran approved antenna.

Navigation menu