TECNO MOBILE CA6 Mobile Phone User Manual Sanjeev

Download:
Mirror Download [FCC.gov]
Document ID	3715087
Application ID	IRrFBq/RT9K0aA0xG8w4QA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	44.43kB (555355 bits)
Date Submitted	2018-01-16 00:00:00
Date Available	2018-01-16 00:00:00
Creation Date	2018-01-08 11:27:52
Document Lastmod	2018-01-08 11:27:52
Document Title	Sanjeev
Document Creator	WPS Office
Document Author:	daishengsheng

Explosion diagram specification
11
13
15
17
19
21
23
25
27
LCM Assembly
Sidkey FPC
Card Slot seal foam
Receiver seal foam
Front CAM seal foam
PS rubber
Back Camera
Audio jack rubber
Front CAM Conductive Fabric
Coaxial Cable 2
Fingerprint Frame
Back CAM lens
Fingerprint Module
LCM BTB Mylar
10
12
14
16
18
20
22
24
26
28
Front Housing Assembly
Front housing rubber
Receiver Deco
Receiver
LED rubber
Front Camera
Card Holder
Main PCB
Shield Graphite Film
Back Flash Seal Foam
Screw
Fingerprint Conductive Foam
LCM Connector Pressed Steel
Battery
29
31
33
35
37
Battery Cover Assembly
Speaker
Motor
Main FPC
PCBA
30
32
34
36
38
Screw
Main Mic Rubber
Coaxial cable 1
Usb Rubber
Speaker FPC
Know your phone
Front camera
Volume key
Power key
SIM/SD card installation
1. Power off mobile.
2. Refer to the following picture for SIM / SD card installation.
Charging the phone
You can charge your device using a charger or by connecting it
to the computer using a USB cable (comes with the phone).
1. Please remind the front and back of the plug.
2. Use only TECNO charger and cables. Other chargers or cables
may damage the device or your device. This will invalidate
your phone warranty.
FCC Caution
Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject
to the condition that this device does not cause harmful interference.
Information to user.
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Information to the user.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information:
This Mobile phone meets the government's requirements for exposure to
radio waves. The guidelines are based on standards that were developed
by independent scientific organizations through periodic and thorough
evaluation of scientific studies. The standards include a substantial safety
margin designed to assure the safety of all persons regardless of age or
health.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is
1.6 W/kg averaged over one gram of tissue. Device types: CA6(FCC ID:
2ADYY-CA6 ) has also been tested against this SAR limit. The highest
SAR value reported under this standard during product certification for
use at the ear is 0.37 W/kg and when properly worn on the body is 1.02
W/kg. This device was tested for typical body-worn operations with the
back of the handset kept 10mm from the body. To maintain compliance
with FCC RF exposure requirements, use accessories that maintain a
10mm separation distance between the user's body and the back of the
handset. The use of belt clips, holsters and similar accessories should not
contain metallic components in its assembly. The use of accessories that
do not satisfy these requirements may not comply with FCC RF exposure
requirements, and should be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with
RF exposure requirements, a minimum separation distance of 1.0 cm
must be maintained between the user’s body and the handset, including
the antenna. Third-party belt-clips, holsters, and similar accessories used
by this device should not contain any metallic components. Body-worn
accessories that do not meet these requirements may not comply with RF
exposure requirements and should be avoided. Use only the supplied or
an approved antenna.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Page Count                      : 7
Author                          : daishengsheng
Comments                        : 
Company                         : 
Create Date                     : 2018:01:08 11:27:52+03:27
Creator                         : WPS Office
Modify Date                     : 2018:01:08 11:27:52+03:27
Producer                        : 
Source Modified                 : D:20180108112752+03'27'
Subject                         : 
Title                           : Sanjeev
Trapped                         : false

EXIF Metadata provided by EXIF.tools