TESSERA TECHNOLOGY 0001 ZigBee RF4CE Module Board User Manual TK RF8058 SB UM E

TESSERA TECHNOLOGY INC. ZigBee RF4CE Module Board TK RF8058 SB UM E

User Manual

Download: TESSERA TECHNOLOGY 0001 ZigBee RF4CE Module Board User Manual TK RF8058 SB UM E
Mirror Download [FCC.gov]TESSERA TECHNOLOGY 0001 ZigBee RF4CE Module Board User Manual TK RF8058 SB UM E
Document ID1266888
Application IDX5UJ/iRqGVCcDRkWkhxG9Q==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize136.89kB (1711168 bits)
Date Submitted2010-04-14 00:00:00
Date Available2010-04-15 00:00:00
Creation Date2010-03-23 18:51:15
Producing SoftwareAcrobat Elements 7.0 (Windows)
Document Lastmod2010-03-23 18:51:15
Document TitleMicrosoft Word - TK-RF8058+SB_UM_E.doc
Document CreatorPScript5.dll Version 5.2
Document Author: remote

User’s Manual
TK-RF8058+SB
ZigBeeTM/RF4CETM-ready
Wireless Network Evaluation Board
Date published: March 8, 2010
Rev. 5.0
© TESSERA TECHNOLOGY INC.
Printed in Japan
-1-
Welcome to the world of TK-RF8058+SB.
You are now being navigated to the design environment
of the μPD78F8058 microcontroller for developing
wireless network applications. Please follow the tutorial
step by step.
-2-
[NOTES]
The information in this document is subject to change without notice. No part of
this document may be copied or reproduced in any form or by any means without
the prior written consent of TESSERA TECHNOLOGY INC.
TESSERA TECHNOLOGY INC. assumes no liability for infringement of patents or
copyrights of third parties by or arising from use of a product described herein.
This product is designed and manufactured with intention for use in evaluation
and prototyping by engineers with knowledge of security, safety and reliability.
TESSERA TECHNOLOGY INC. would like to inform, that the standard quality
assurance procedure(s) have not been fully applied to this product and its
documentation and that TESSERA TECHNOLOGY INC. cannot assure the full
and error free function and/or the standard quality level.
[CAUTION]
This equipment should be handled like a CMOS semiconductor device. The user
must take all precautions to avoid build-up of static electricity while working with
this equipment. All test and measurement tool including the workbench must be
grounded. The user/operator must be grounded using the wrist strap. The
connectors and/or device pins should not be touched with bare hands.
-3-
[FCC WARNING & NOTICE]
●Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
●The intended use of the product is generally not for the general public.
It is generally for industry/commercial use by the professional electric engineer.
To be in compliance with FCC 15.203 requirements, the product must be
installed by professional installers with approved antenna that was included in
the product.
Class B:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
●this device may not cause harmful interference, and
●this device must accept any interference received, including interference that
may cause undesired operation.
●The host device shall also comply with the certification labeling requirements of
each of the modules it contains.
●A reference to the enclosed module displaying its FCC ID certification number.
Recommended wording:
Contains FCC ID: X8U0001
-4-
Contents
INTRODUCTION........................................................................................... 8
PREPARATIONS........................................................................................ 10
2.1
Development Tools, Sample Programs, and the MAC Library.................................. 11
2.1.1 Integrated Development Environment PM + V6.31 .......................................................... 11
2.1.2 Device file DF788058 e1.00b ........................................................................................... 11
2.1.3 C Compiler CC78K0R W2.12 : Code size limited version................................................ 11
2.1.4 Assembler RA78K0R W1.33 : Code size limited version ................................................. 11
2.1.5 78K0R integrated debugger ID78K0R-QB V3.60 ............................................................. 11
2.1.6 Built-in Flash Memory Writing Program WriteEZ5............................................................ 11
2.1.7 78K0R Starter Kit Setting.................................................................................................. 11
2.1.8 Starter kit USB driver ........................................................................................................ 12
2.1.9 The RF Test Program ....................................................................................................... 12
2.2
Installation of Software Development Tools............................................................... 13
2.2.1 Start-up of the installation CD-ROM ................................................................................. 13
2.2.2 Installation of the software development tools.................................................................. 13
2.2.3 Uninstall ............................................................................................................................ 20
2.2.4 File Configuration in PC.................................................................................................... 21
2.3
USB Driver .................................................................................................................... 22
2.3.1 Install to Windows XP ....................................................................................................... 23
2.3.2 Install to Windows2000..................................................................................................... 26
2.3.3 Confirmation of the installation ......................................................................................... 30
2.4
Sample Environment .................................................................................................... 31
2.4.1 Installation of the sample programs.................................................................................. 32
2.4.2 File Configuration of the sample program ........................................................................ 34
EXPERIENCES........................................................................................... 35
3.1
Starting PM + ................................................................................................................ 37
3.2
Introduction to PM +..................................................................................................... 38
3.3
Loading Workspace (Project) ...................................................................................... 40
3.4
Configuration of Linker Option.................................................................................... 42
3.4.1 "Output1" Tab ................................................................................................................... 42
3.4.2 "Output2" Tab ................................................................................................................... 44
-5-
3.5
Configuration of Compiler Option............................................................................... 45
3.5.1 "Extend" Tab ..................................................................................................................... 45
3.5.2 "Startup Routine" Tab ....................................................................................................... 46
3.6
Configuration of Debugger setting ............................................................................. 47
3.7
TK board setting ........................................................................................................... 49
3.8
Creating execution format ........................................................................................... 50
3.9
Starting integrated debugger (ID78K0R-QB) .............................................................. 52
3.10
Introduction of the integrated debugger (ID78K0R-QB) ........................................... 57
3.11
Executing a program .................................................................................................... 58
3.12
Stop a program ............................................................................................................. 59
3.13
Terminating integrated debugger (ID78K0R-QB) ....................................................... 60
3.14
The RF Test Program ................................................................................................... 61
3.14.1 Procedure for one to one transmit/receive test .............................................................. 61
3.14.2 PER test / receiver.......................................................................................................... 73
3.14.3 Continuous TX / Pseudo Noise ...................................................................................... 73
3.14.4 Continuous TX / Raw carrier .......................................................................................... 73
3.14.5 RX Mode ......................................................................................................................... 73
3.14.6 IDLE MODE .................................................................................................................... 73
3.14.7 Standby MODE............................................................................................................... 73
3.14.8 Deep Sleep mode ........................................................................................................... 73
3.14.9 Power down mode .......................................................................................................... 73
3.14.10 Set RF channel ............................................................................................................. 74
3.14.11 Manually set UZ2400 register....................................................................................... 74
3.14.12 Resetting RF................................................................................................................. 74
3.15
4.1
Terminating PM +.......................................................................................................... 75
HARDWARE SPECIFICATIONS................................................................ 76
Layout of hardware functions...................................................................................... 77
4.2
Hardware Functions ..................................................................................................... 78
4.2.1 SW4 (Dip Switch).............................................................................................................. 78
4.2.2 SW5 .................................................................................................................................. 78
4.2.3 SW6 .................................................................................................................................. 78
4.2.4 JP1.................................................................................................................................... 78
4.2.5 JP2.................................................................................................................................... 78
-6-
4.2.6 JP3 ..................................................................................................................................... 79
4.2.7 JP4 ..................................................................................................................................... 79
4.2.8 JP5 ..................................................................................................................................... 79
4.2.9 SW1,SW2,SW3...................................................................................................................... 79
4.2.10 SW7................................................................................................................................... 79
4.2.11 LED4 ................................................................................................................................. 80
4.2.12 LED1, LED2, and LED3....................................................................................................... 80
4.2.13 FP1 ................................................................................................................................... 80
4.2.14 J2 and J3 .......................................................................................................................... 80
4.3
Summary of Power Supply Settings ........................................................................... 80
4.4
Solder-short pad........................................................................................................... 81
5.1
TROUBLESHOOTING................................................................................ 82
If you cannot find USB driver when you connect PC to the kit................................. 82
5.2
Error when you start the debugger ............................................................................. 82
5.2.1 "Can not communicate with Emulator..." (F0100 or A0109)............................................. 83
5.2.2 "Incorrect ID Code." (Ff603) ............................................................................................. 83
5.2.3 "The on-chip debug function had been disabled in the device." (F0c79) ......................... 84
5.2.4 "Disabling the on-chip debug function is prohibited." (F0c33).......................................... 84
OTHER INFORMATION ............................................................................. 85
6.1
Create a new workspace .............................................................................................. 86
6.2
Registration of new source files.................................................................................. 91
6.3
Debugger tips ............................................................................................................... 93
6.3.1 Change display of buttons ................................................................................................ 93
6.3.2 Display source list and function list................................................................................... 93
6.3.3 Set/delete breakpoints ...................................................................................................... 94
6.3.4 Display global variables .................................................................................................... 95
6.3.5 Display global variables while programs are running ....................................................... 96
6.3.6 Display local variables ...................................................................................................... 97
6.3.7 Display memory and SFR contents .................................................................................. 97
6.4
Erase of flash memory ................................................................................................. 98
6.5
BOM List, Circuit diagram & Pin Connection ........................................................... 104
MODE SETTING OF THE BOARD........................................................... 110
-7-
1 Introduction
Target Reader
Software development engineers who wish to become
familiar with the development environment of the 78K0R
microcontrollers. It is assumed that the readers have been
familiar with basics of microcontrollers, C and assembler
languages, and the WindowsTM operating system.
Purpose
For readers to become familiar with the design environment
and the application examples of wireless networks.
Overview
This manual consists of the following contents
Chapter 1 Introductions
→Overview of this manual
Chapter 2 Preparations
→Introduction of soft tools, and sample programs and installation
Chapter 3 Experiences
→ Guide to the basic operations of PM + and the integrated
debugger using sample programs.
Chapter 4 Hardware Specifications
→Explain the hardware of TK-RF8058+SB
Chapter 5 Troubleshooting
→Describe how to solve troubles you may face, such as errors when
starting the integrated debugger (ID78K0R-QB)
Chapter 6 Other Information
→Introduce other information, such as how to create a new
workspace (project) on integrated development environment (PM+),
how to register additional source file, and some useful tips of the
integrated debugger.
The circuit diagrams of demonstration kit are included in this
chapter.
Chapter 7 Mode Setting of the Board
→ Explanation of switch setting.
-8-
Trademark
Microsoft and Windows are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or
other countries.
Adobe and Acrobat are trademarks of Adobe Systems
Incorporated (Adobe System Incorporated).
Other company names and product names that appear in this
document are the registered trademarks or trademarks of their
respective companies.
-9-
2 Preparations
This chapter introduces the development environment and describes how to
install the sample programs. The sample program can be tested on this
hardware platform of the evaluation kit.
- 10 -
2.1
Development Tools, Sample Programs, and the MAC Library
This section outlines the development tools, sample programs and the MAC
library used in this tutorial.
2.1.1 Integrated Development Environment PM + V6.31
This is a project manager, where you work for editing the source code,
compiling it, and initiating the debugger. The project manager works on MS
Windows 2000 or XP.
2.1.2 Device file DF788058 e1.00b
A device file contains an MCU specific information. It instructs the
development tools what kind of an MCU the tools shall work for.
2.1.3 C Compiler CC78K0R W2.12 : Code size limited version
This is a free compiler for the 78K0R microcontrollers. The object code size
is limited to 64 Kbytes. It works on MS Windows 2000 or XP.
2.1.4 Assembler RA78K0R W1.33 : Code size limited version
This is a free assembler for the 78K0R microcontrollers. The object code
size is limited to 64 Kbytes. It works on MS Windows 2000 or XP. The
RA78K0R Assembler Package contains Structured Assembler
Preprocessor, Assembler, Linker, Object Converter, Librarian, and List
Converter.
2.1.5 78K0R integrated debugger ID78K0R-QB V3.60
The Integrated Debugger ID78K0R-QB offers a debug environment on
your PC, where the MS Windows 2000 or XP runs, if the TK board is
connected to the PC with USB. The USB I/F accesses to the OCD, On
Chip Debug, interface on the microcontroller.
2.1.6 Built-in Flash Memory Writing Program WriteEZ5
This is the Windows software to write programs on built-in flash memory.
By connecting TK-RF8058+SB and PC with bundled USB cable, you can
write/delete programs on the built-in flash memory.
2.1.7 78K0R Starter Kit Setting
If you forget about the security ID or if you set “Does not erases data of
flash memory in case of failures in enabling on-chip debugging”, you can
- 11 -
erase the flash memory by using this starter kit.
2.1.8 Starter kit USB driver
This is a software driver for PC to access to the USB interface of the
TK-RF8058+SB board.
2.1.9 The RF Test Program
The RF Test Program is used in [chapter 3 Experiences].
The RF Test Program is provided in the form of the C source codes.
If you wish to tailor the RF Test Program to meet your specific needs, you
can edit the source code, re-compile it with debug build to generate a load
module file, then, start the debugger to load the tailored execution code on
to the microcontroller for further debugging on the project manager PM +.
Alternatively, if debugging is not required, you can make a release build to
achieve a new hex file, on the project manager PM +.
As a general remark, please respect your local regulation of
electro-magnetic emission. In general, it is suggested to use the
TK-RF8058+SB board in a radio anechoic chamber.
- 12 -
2.2
Installation of Software Development Tools
2.2.1 Start-up of the installation CD-ROM
The attached CD-ROM contains Development Tools, documents and sample
soft ware.
You can install it using an installer.
2.2.2 Installation of the software development tools.
Please insert the CD-ROM in the drive. The installer will show up automatically.
If it does not start automatically, please initiate it by double clicking the
SETUP.EXE.
<1> Readme First
The contents of the CD-ROM, and some notes are available.
Please read it at first.
<2> Install…
Click “Install” to start installation of development tools.
For details, please refer to the next section.
- 13 -
<3> Documents
Manuals of development tools and the evaluation kit are available in PDF
files.
When this button is clicked, the WWW browser will start. Adobe® Acrobat®
Reader is available in the CD-ROM.
<4> Sample Program
Click this button to start the WWW browser for the sample program and the
tutorial.
<5> Link to NEC Electronics Microcontrollers
Click this button to start the WWW browser display the link to the NEC
Electronics Microcontroller web site
(http://www.necel.com/micro/index_e.html)
The NEC Electronics Microcontroller web page provides with the latest
product/tool information and FAQs.
<6> Exit
Terminate the setup.
- 14 -
①
Select products that you need to install.
(as default, all the products that you need to use the demostration kit
are selected.)
"Explain" area displays an explanation of the selected product.
To change the installation destination, click Browse… .
When all the settings are completed, click
Install…
* In this document, it is assumed that users install the programs under "NEC
Electronics Tools" directory (default installation directory). Users can find the
tools by selecting “Start Menu” -> "Programs" -> "NEC Electronics Tools".
- 15 -
②
Click
OK
when "Install" comfirmation dialog box is opened.
③
Read "software license agreement" and click Yes
installation.To stop the installation, click No .
- 16 -
for continuing the
④
Enter the product ID, and click Next .
* The product ID is available on the “README.html” the other sheet.
⑤
It starts copying the files.
- 17 -
⑥
When the installation is completed, the following dialog opens.
Click OK .
⑦
"NEC Electronics Starter Kit Virtual UART" USB driver must be installed on
PC before you connect to TK-RF8058+SB . Install the USB driver by
referring "2.3USB Driver".
- 18 -
Notes on the installation authority
To install this tool in Windows 2000 or XP, the authority of a administrator is
necessary. Therefore, please login as an administrator.
Notes on the install-directory
Please do not use 2-byte characters, such as umlaut in the directory name,
where the product is to be installed.
Note on the version of Windows
If the language of the Windows is not English, a file transfer error during
installation might be observed. In this case, please abort the installation in
the language, and re-install it in an English version of Windows.
The identical problem may be observed, if a language other than English is
specified as the system language in the “Regional Settings Properties” tab.
- 19 -
2.2.3 Uninstall
<1>
Start "Add /Remove Programs" in the Control Panel.
(Example here is based on Windows2000)
<2>
Select the tool that you want to uninstall from the list displayed in
"Install/Uninstall" and click [Add/Remove...].
<3> A dialog box for confirming deletion of files will be displayed.
Yes . Deleting of the files will be started.
<4>
When the completion message is displayed, click
OK
Caution:
Deletion of some files may be asked during uninstallation.
deletion of these files causes no problem.
<5>
This completes uninstalling this tool.
- 20 -
Click
Normally,
2.2.4 File Configuration in PC
Software Development Tools are installed in "C:¥Program Files¥NEC Electronics
Tools" on default setting.
When you use the tools, please open the tools from [Start menu] ->
[Programs]->[NEC Electronics Tools].
- 21 -
2.3
USB Driver
You need to install “NEC Electronics Starter Kit Virtual UART” in your PC.
When TK-RF8058+SB is used, it is necessary to install the “NEC Electronics Starter Kit
Virtual UART” driver in the host machine. Please install the driver according to the following
procedures with appending CD in the drive.
"Starter Kit USB Driver" must be installed on the PC. If not, please refer to "2.2 Installation of
Software Development Tools" to install the “Starter Kit USB Driver” first.
Attention
Do not use a USB hub for connecting TK-RF8058+SB .
Depending on the version of Windows OS, the installation will be differed.
Please check your Windows version, and follow the instructions
- Windows XP
-> "2.3.1Install to Windows XP"
- Windows 2000
-> "2.3.2Install to Windows2000"
After the installation, go to "2.3.3Confirmation of the installation"
- 22 -
2.3.1 Install to Windows XP
１．
Once the TK-RF8058+SB is connected with USB, the "Found New Hardware Wizard"
will be started. Select "No, not this time" and click Next > .
Select "No, not this time"
Click "Next"
２．
Select "Install from a list or specific location" and click
Next >
Select "Install from a list or specific
location"
Click "Next"
- 23 -
３．
Select "Search for the best driver in these locations.” , check "Include this location in
the search:", and then click "Browse..." to select the driver directory path. The path
should be "C:¥Program Files¥NEC Electronics Tools¥TK-driver" as default installation.
If the installation directory is not default, then select "TK-driver" under the installation
directory.
Click Next > .
Select the driver directory
Click "Next"
４．
If the following dialog is opened, click
Continue Anyway
Click "Continue Anyway"
- 24 -
５．
The installation of "NEC Electronics Starter Kit Virtual UART" driver is completed.
Click Finish .
Click "Finish"
６．
Go to "1.3.3 Completion of the installation".
- 25 -
2.3.2 Install to Windows2000
１． Once the TK-RF8058+SB is connected with USB, the "Found New Hardware Wizard" will
be started.
Select "No, not this time" and click Next > .
Click
- 26 -
２． Select "Search for a suitable driver for my device".
Click Next > .
Select "Search for a suitable driver for my
device"
Click "Next"
３． Select "Specify a location".
Click Next > .
Select "Specify a location"
Click "Next"
- 27 -
４． Select the driver directory path. The path should be "C:¥Program Files¥NEC
Electronics Tools¥TK-driver" as default installation.
If the installation directory is not default, then select "TK-driver" under the installation
directory.
Click OK .
Click "OK"
Select the driver directory
５．
Click
Next >
Click "Next"
- 28 -
６．
The installation of "NEC Electronics Starter Kit Virtual UART" driver is completed.
Click Finish .
Click
７．
Go to "1.3.3 Confirmation of the installation".
- 29 -
2.3.3 Confirmation of the installation
Please confirm “NEC Electronics Starter Kit Virtual UART(COMx)” in the device
manager of system in the control panel of the MS Windows.
Device Manager
It is confirmed that “NEC
Electronics Starter Kit Virtual
UART(COMx)” exists.
The screen above shows that the COM port number is "COM8". If ID78K0R-QB is
not in use, you can use this port number for connecting TK-RF8058+SB.
When you change the USB port connection, the COM port number will be
changed as well.
Select this COM port number when you use WriteEZ5.
CAUTION
・Do not do “Hardware Modification Scan” when you communicate with the target device.
- 30 -
2.4
Sample Environment
This section explains the overview and preparation of sample programs.
You need to install the sample programs on your system first before using them.
How to install the sample programs and where they should be intalled on your
system will be explained.
- 31 -
2.4.1 Installation of the sample programs
Insert the CD-ROM disk in the CD-ROM drive of your PC. The [NEC Electronics
Microprocessor Development Tools Setup] screen automatically appears.(if this screen does
not appear automatically, start setup.exe from Explorer. etc.)
Press the Sample Program button to start the WWW browser, and then click the
[TK-RF8058+SB Sample Programs] link.
The WWW browser
starts up.
Click the [TK-RF8058+SB Sample
programs] link you can also
download the [User's Manual]
When[TK-RF8058+SB Sample Programs] is clicked, the following download
confimation window appears.
- 32 -
Click the
Save
butten.
After specifying the download destination folder，click the
Save
button.
The self-extraction sample program (TK78K0R.exe) is copied to the specified
folder.
The folder that the “TK78K0R” folder is made when this file is executed, and the
sample program is stored under the” TK78K0R” folder.
- 33 -
2.4.2 File Configuration of the sample program
The sample programs ware the following folders.
TK78K0R
SAMPLE_RF8058+SB
TKRF8058SB_RF_Test
The sample program used in chapter 3.
The packet error rate and received signal
- 34 -
3 Experiences
Now you are ready to experience the operation of the TK-RF8058+SB using the
integrated development environment, PM +.
As a program for the TK-RF8058+SB, the RF test program (RF_Test) which you
installed in "2.4.1Installation of the sample programs" is used.
Later in this chapter, you will learn how to generate an executable file, how to
download it to the Flash, and how to execute the program.
You can understand the basic operation of the development tools (PM+,
ID78K0R-QB) and the basics of the project files that you need when you develop
application programs.
- 35 -
The overall flow is as follows.
Starting PM +
Loading workspace (project)
Reviewing Linker, Compiler option, Debug setting
TK board setting
Creating execution format
Operation
Starting integrated debugger (ID78K0R-QB)
Executing program
Stopping program
Terminating integrated debugger (ID78K0R-QB)
Terminating PM +
- 36 -
3.1 Starting PM +
In the Windows Start menu, select [Programs]->[NEC Electronics Tools]->[PM +
V6.31]
PM + start up
- 37 -
3.2 Introduction to PM +
In PM +, application programs and environment setting are handled as a single Project, and series of actions
such as program creation using the editor, source management, build, and debugging are managed.
Also, one of more project files is managed together as a workspace.
Menu bar
Project window
Project window
Tool bar
Output window
A window in which project names, source files, and include file are displayed using a
tree structure.
Output window
A window in which the build execution status is displayed.
For details regarding menu bars and tool bars, refer to the PM + User’s Manual.
- 38 -
What is a project?
A project is the unit in which PM + executes management, and refers to an application system
and environment development based on PM +.
PM + complies project information and saves it in a “project file”, from which it is then referenced.
What is a project file?
A project file is a file to which information such as the source file to be used in the project, the
device name, the tool options for complying, and the editor and debugger to be used have been
saved as “project information”.
The file name format is “ΔΔΔΔprj”.
Project files are created in folders that are set when creating new workspaces.
What is a project group?
A project group is a group comprised of a number of projects in an application system.
The target devices of each project that can be registered to one project group must be the
same.
What is a workspace?
A workspace is the unit used to manage all the projects or project group required for one
application system.
The file name of multiple project files is saved to a workspace file for referencing.
The file name format is “ΔΔΔΔprw”.
- 39 -
3.3 Loading Workspace (Project)
In this section, you will use the workspace that you created in "2.4Sample Environment"
For creating a new workspace, refer to "6.1Create a new workspace".
The workspace has information about the build environment for the sample programs.
Select "File" on menu bar and "Open Workspace…".
Then, select “C:¥TK78K0R¥SAMPLE_RF8058+SB¥TKRF8058SB_RF_Test¥RF_Test.prw” .
- 40 -
Open the folder in which the
sample program is located.
“RF_Test.prw”and then press the
Open
button.
Workspace file name :RF_Test.prw
The “RF_Test.prw” workspace
file is read
Project group
Project
- 41 -
3.4 Configuration of Linker Option
The linker options have been set by the project file. However, some option settings will be
covered in this section because the linker option settings are important for debugging.
Following three settings are covered specifically.
- Outputs from debugging
- On-chip debug (bytes, security ID)
- Watchdog timer
Select "Tools" on menu bar, then "Linker options".
3.4.1 "Output1" Tab
Select "Output1" tab on "Linker Options" window, and see following settings.
- 42 -
- Load Module File settings
Check "Output Symbol Information".
This enables to do source level debugging (setting break points, monitoring variables in
watch window, etc).
Also, you can specify the load module file name.
- On-Chip Debug Option Byte
Check "On-Chip Debug Option Byte". Enter "85" in "Control value". This setting enables
the on-chip debugging function of the microcontroller.
*For details of "Control value", refer to the user's manual of 78K0R/KG3 (U17894E).
See "Start address" is set to "1FC00", and "Size" is set to "1024".
These settings reserve the memory address area for the monitor program (the flash
memory area that the debugger uses for on-chip debugging).
In this case, the "Control value" is allocated to the address of C3H in flash memory, and
FFH is set to the next address. Because of this, the following areas could not be set the
segments.


- 2H, 3H
- CEH-D7H
- From the address set in "Start address" to the byte set in "Size"
- Security ID
Check "Security ID", and enter the security ID which is a unique ID code (10 bytes) to
authenticate when the debugger is launched.
The security ID is stored in the flash memory (C4H-CDH), and checked if it is the same
as the code entered in Linker options dialog when the debugger is launched.
The debugger will not be launched when the security ID is unmatched. By using this
function, you can secure the programs from leaks.
If you do not need to set the security, it is recommended to set the security ID
"FFFFFFFFFFFFFFFFFFFF" as this is the initial code.
If you forget about the security ID (stored in the address of C4H-CDH) or if you set wrong
on-chip debug option byte, you will not be able to use the debugger (ID78K0R-QB).
In this case, you need to use "WriteEZ5" to erase the built-in flash memory. By erasing
the flash memory, the security ID is set to "FFFFFFFFFFFFFFFFFFFF".
For details, refer to "6.4Erase of flash memory".
- 43 -
3.4.2 "Output2" Tab
Select "Output2" tab on "Linker Options" window, and see following settings.
- User Option Byte
Check "User Option Byte", and then enter "EFFBFF". Here, you can do the
setting of watchdog timer, low-voltage detector, and system reserved
memory area. The 3 bytes you entered are stored at C0H-C2H on flash
memory:
- C0H: setting for watchdog timer
- C1H: setting for low-voltage detector
- C2H: setting for system reserved memory area (must be set as FFH)
This time, you disabled the watchdog timer and the default start function of
low-voltage detector.
For details, refer to the user's manual for uPD78F8058.
- 44 -
3.5 Configuration of Compiler Option
The compiler options have been set by project file. However, because some
compiler options are useful, following two settings are covered specifically in this
section.
- Enable C++ comments
- Use multiplier and divider
Select "Tools" on menu bar, then "Compiler options".
3.5.1 "Extend" Tab
Select "Extend" tab, and check "Enable C++ Comment".
This setting allow you to use the C++ comment using "//".
It is useful feature when developing code.
- 45 -
3.5.2 "Startup Routine" Tab
Select "Startup Routine" tab, and check "Using Library" and "Using
Multiplier/Divider". The Microcontroller has feature of multiplier/divider to increase
those calculation speed.
- 46 -
3.6
Configuration of Debugger setting
Please Choose [Tool] -> [Debugger Setting] at the pull-down menu.
- 47 -
Check if "ID78K0R-QB V3.60 78K0R Integrated Debugger" is selected on
"Debugger".
- 48 -
3.7
TK board setting
Please set the switches on the TK-RF8058+SB board as follows.
ON
ON
ON
SW4 setting
ON
ON
ON
OFF
OFF
JP5：Any
JP3：
1-2short(USB)
SW5：3.0V
SW6：
「Debug/Writer」
JP2：
JP1：short
JP4：short
1-2short(Regulator)
After the switch settings are completed, connect the PC to USB1 on
TK-RF8058+SB with USB cable.If the "Found New Hardware Wizard" is started,
install USB driver with referring "2.3USB Driver".
- 49 -
3.8
Creating execution format
Please go back to PM +.
Please re-compile the project by clicking the
button at the menu bar.
Build process is
executed
Build has been completed successfully.
- 50 -
What is build ?
Build is a function that creates an executable file, etc., from a source file registered to a project.
PM + automatically performs compiling, linking, and other processing actions.
On the second and subsequent build, PM + also automatically delects files that have been updated
from the previous build processing, and complies and assembles only the relevant files, thereby reading
the time required for build processing.
What is rebuild ?
Build compiles and assembles only the source files that have been updated since the previous
time, whereas rebuild compiles and assembles all the source files.
When setting, such as compiler options, have been changed, not build, but rebuild, must be
Selected.
- 51 -
3.9
Starting integrated debugger (ID78K0R-QB)
Please select the Debug button
→[Debug(D)].
，of PM +, or in the menu, select [Build(B)]
If the debug button is not displayed, in the menu, select [Tool]→[Debugger
Setting...]“ID78K0R-QB V3.60 78K0R Integrated Debugger”
ID78K0R-QB is launched
- 52 -
Then, you will see the Configuration dialog.
Please choose “Tool0+Tool1” in the "Target Device Connection", and choose
"4.00MHz" in the "Main Clock", then, please input 20 Fs,
0xFFFFFFFFFFFFFFFFFFFF, in the ID Code.
Then, please click “OK”.
Click
Yes
when the confirmation dialog for downloading load module file is opened.
- 53 -
ID78K0R-QB starts and downloading
the program to flash memory.
When the download is
completed, the source
code will be displayed
NOTE:
Completion of the download does not mean running the programs. To run the sample
programs, go to "3.11 Executing program".
- 54 -
Normally, if communication with the CPU fails, the following error messages are
output.
If you observe the message please confirm the following items.
1． Please confirm the switch on the board is set as follows.
SW4
Bit1
Bit2
Bit3
Bit4
Bit5
ON
Bit6
ON
Bit7
OFF
Bit8
OFF
ALL ON
SW6
SW5
JP3
JP5
JP2
JP1
JP4
「Debug/Writer」
3.0V
1-2short(USB)
Any
1-2 short (Regulator)
Short
Short
２． Please confirm the power LED4 is lighted.
After checking the above items, start ID78K0R-QB again.
- 55 -
If the ID code is wrong, you may find the following messages on the display.
The following "Configuration" screen is displayed when OK is pushed and input a
correct ID code, please.
The default setting of the ID code is ”0xFFFFFFFFFFFFFFFFFFFF”. You can set
an alternative ID code on the linker option tab.
If the setting of On-Chip Debug Option Byte is "Does not erase data of flash
memory in case of failures in enabling on-chip debugging" and if you forget the
security ID, you need to erase the flash memory completely.
To erase the flash memory, please refer to the section 6.4, “Erasing the Flash
Memory”.
- 56 -
3.10 Introduction of the integrated debugger (ID78K0R-QB)
ID78K0R-QB displays the internal status of the CPU and controls monitor
functions in the main window.
The initial screen of ID78K0R-QB is as follows.
< Main window＞
Menu bar
Tool bar
Window display area
Status bar
For more details, please refer to the user’s manuals of ID78K0R-QB.
- 57 -
3.11 Executing a program
If you click “GO”
, the execution of the code will start.
You can know it by the red bar at the bottom.
Execute the program
While a program is running, the status bar will be red.
- 58 -
3.12 Stop a program
Now, you are going to stop the program.
Press the ID78K0R-QB’s stop button
, or in the menu, select [Run]→[Stop].
Stop the program
When the program stops, the status bar changes back to the original color.
- 59 -
3.13 Terminating integrated debugger (ID78K0R-QB)
Select "File" on menu bar, then "Exit".
The Exit confirmation dialog box is
displayed.
If you push the “Yes”, ID78K0R-QB is terminated after preserving a present
environment.
If you push the “No”, ID78K0R-QB is terminated without preserving a present
environment.
- 60 -
3.14 The RF Test Program
3.14.1 Procedure for one to one transmit/receive test
Assumption here in this section is, you have two TK-RF8058+SB boards, in one of which the
execution code for the “RF_TEST” was programmed by the debugger. You also prepare two
PCs or one PC with more than one usb interface.
We will use the board you have downloaded the executable program with the short address
0x0001 as a transmitter. We now learn how to prepare an executable program for receiver
side, which may be assigned a short address of 0x0002.
Transmitter
Receiver
Short address : 0001
Short address : 0002
Settings for a receiver
1). Please start-up the PM+ from the
“C:/TK78K0R/SAMPLE_RF8058+SB/TKRF8058SB_RF_Test/RF_Test.prw”
2). Please choose [Tool(T)] → [Compiler Options] Æ [Preprocessor]
- 61 -
3). Please alter the Macro Definition from “CPU78K0R,MAC_ADDR=0x0001” to
“CPU78K0R,MAC_ADDR=0x0002”.
4). Now, you set the short address of the receiver at 0x0002.
5). Please set the switches on the receiver as follows,
SW4
6).
7).
8).
9).
Bit1
Bit2
Bit3
Bit4
Bit5
ON
Bit6
ON
Bit7
OFF
Bit8
OFF
ALL ON
SW6
SW5
JP3
JP5
JP2
JP1
JP4
Debug/Writer
3.0V
1-2short (USB)
Any
1-2 short (Regulator)
Short
Short
button, or select [Biild(B)]→[rebuild(R)].
Then, please rebuild it by pushing the
You will follow the instructions in the chapter 3.9.
If you complete the download of the load module file, please close the debugger.
Then, please remove the USB cable.
- 62 -
10). Then, the board setting is configured as follows as a receiver.
SW4
Bit1
Bit2
Bit3
Bit4
Bit5
ON
Bit6
ON
Bit7
OFF
Bit8
OFF
ALL
OFF
SW6
SW5
JP3
JP5
JP2
JP1
JP4
「K0R-K0USB」
3.0V
1-2 Short(USB)
Any
1-2 Short (Regulator)
Short
Short
11). Connect the board with a PC by a USB cable, then you will find the Power LED lit on the
board.
- 63 -
12).Then, we need a hyperterminal on the PC.
13). On MS-Windows in your PC, please select [All Programs] -> [Accessory] ->
[Communication] -> [HyperTerminal]
14).You may assign your favorite name on a connection. Then, click OK.
15).You need to learn the COM port number you connected the USB cable. If you
don’t know the com port number, please find it at [Control Panel] Æ [System]
Æ [Hardware] Æ [Device Manager] Æ [Port (COM and LPT)].
- 64 -
Bits per second
Data bits
Parity
Stop bits
Flow control
115200
None
None
(Property -> Setting -> ASCII)
Local Echo OFF
No Line Feed
16).Please set the COM port at 115200 bps, 8 data bits, no parity, 1 stop bit, and
no flow control.
Then, please click “OK”.
17).Then, please reset the receiver board by pressing the SW7.
18).Now you will find the following opening menu in the window.
- 65 -
19).Please select “2” from the MENU to start the board as a receiver.
Command? >2 (PER test/reciever)
[My Profile]
------------------------------------MAC : 22:95:00:02:00:00:00:47
Short : 0002
PanID : 2514
------------------------------------[Set channel to 11 (Cmd)]
20).If you see the display as shown above, the receiver set-up has been
completed.
- 66 -
Settings for a transmitter
1). Please configure the board of a transmitter as follows,
SW4
Bit1
Bit2
Bit3
Bit4
Bit5
ON
Bit6
ON
Bit7
OFF
Bit8
OFF
ALL
OFF
SW6
SW5
JP3
JP5
JP2
JP1
JP4
「K0R-K0USB」
3.0V
1-2 short(USB)
Any
1-2 short(Regulator)
Short
Short
2). Please connect the transmitter board to a PC. Please confirm the LED lit on
the board.
3). Please start-up a hyperterminal for a transmitter.
4). Please reset the transmitter board by pressing the SW7.
5). Now you will find the following opening menu in the window.
- 67 -
6). Please select the command “1” to start the Packet Error Rate test.
Command? >1 (PER test/sender)
[My Profile]
------------------------------------MAC : 22:95:00:01:00:00:00:47
Short : 0001
PanID : 2514
------------------------------------Send to (Short addr) ? :
7). If you see “Send to (Short addr) ? :”, please input the receiver address of
0002.
8). Then, you will be asked how many packets you wish to consume in the PER
test.
9). You may input “1000”.
10).Then, you will be asked the interval of packets in msec.
11).You may input 3 msec.
12).Then, the PER test will be executed.
13). You will see,
Sent: The number of packets sent.
Received: The number of the received packets.
PER: The calculated PER in %.
RSSI: The maximum and minimum RSSI values in the PER test
[Note]
PER= Packet Error Rate
RSSI= Received Signal Strength Indication
------------------------------------Send to (Short addr) ? : 2
Send count (dec)
? : 1000
Interval (dec/msec) ? : 3
[Set channel to 11 (Cmd)]
Prepare to send..OK
[Set channel to 11 (Current)]
Request to result..OK
[Results]
------------------------------------From
: 0001
To
: 0002
------------------------------------Sent
: 1000
Recieved : 1000
PER
0.0000%
RSSI
: max FF / min D0
------------------------------------Press any key to the menu
- 68 -
21).Channel setting
In the previous example, you may have also found the RF channel used in this
test is the Channel 11. The channel is specified by the IEEE 802.15.4
specification.
The channel 11 is assigned at 2405 MHz. You can change the channel in the PER
test in 5MHz step to the maximum channel of 26th at 2480 MHz.
To do it, please press “A” in the command prompt. Then, please choose the
channel by [+], [-], [A], [B], or [C]. In the example below, the channel 23th, 2465
MHz, was selected.
- 69 -
To execute the PER test at the channel 23, press [Enter] in your keyboard, then,
choose “1” to initiate the PER test mode. Then, you may input 1000 packet in 5
msec interval to see the following example. Please confirm the channel used is
23th in the display. Please note the receiver will learn which channel is to be used
for the test automatically.
[My Profile]
------------------------------------MAC : 22:95:78:01:00:00:00:47
Short : 0001
PanID : 2514
------------------------------------Send to (Short addr) ? : 02
Send count (dec)
? : 1000
Interval (dec/msec) ? : 5
[Set channel to 11 (Cmd)]
Prepare to send..OK
[Set channel to 23 (Current)]
Send..
Request to result..OK
[Results]
------------------------------------From
: 0001
To
: 0002
------------------------------------Sent
: 1000
Recieved : 1000
PER
0.0000%
RSSI
: max FF / min FF
-------------------------------------
- 70 -
22).Adjusting the output power
You may wish to control the output power in the PER test.
For it, please select “M” in the menu.
You will be asked the register ID. Please input “203”.
Then you will see, “LREG[203] : 00 >1F”.
It means the current value at the register [203] is 0x00, which means 0 dB.
0x00 is the reset default.
The register bits are defined as follows,
LREG[203]: [7:3] -> small scale tuning
000000: 0 dB
000001: -0.1dB
111111: -8.30 dB
For instance, if you wish -8 dB, please input “1F”, as follows,
“LREG[203] : 00 > 1F”
Then, you will start the PER test.
- 71 -
You may find larger PER value with smaller RSSI value in this case.
Please note this adjustment is applied only to the transmitter. The receiver always
sends back the test results with the 0 dB output power using the channel 11th.
- 72 -
3.14.2 PER test / receiver
The Menu 2 sets the board to the receiver in the PER test.
If you have two PCs, you can connect two boards to each of two PCs, then,
you will apply this mode to one of them.
3.14.3 Continuous TX / Pseudo Noise
The Menu 3 initiates the modulated RF transmission. The data carried are
pseudo random numbers. You can define the channel using the menu 9,
and the output power using the menu 0.
3.14.4 Continuous TX / Raw carrier
The Menu 4 initiates the carrier transmission. The output power is not 0 dB
as a reset default. You can define the channel using the menu 9.
3.14.5 RX Mode
The Menu 5 initiates the receiver mode.
3.14.6 IDLE MODE
The Menu 6 sets the UZ2400 into the IDLE mode.
3.14.7 Standby MODE
The Menu 8 sets the UZ2400 into the Standby mode.
3.14.8 Deep Sleep mode
The Menu 9 sets the UZ2400 into the Deep Sleep mode.
3.14.9 Power down mode
The Menu 0 sets the UZ2400 into the Power down mode.
- 73 -
3.14.10 Set RF channel
The Menu A allows you to set the RF channel.
3.14.11 Manually set UZ2400 register
The Menu M allows you to set the UZ2400 registers.
Please refer to the datasheet for the definition of registers.
3.14.12 Resetting RF
The Menu R allows you to reset the UZ2400 registers.
- 74 -
3.15 Terminating PM +
In the PM + menu, select [File]→[Save Workspace].
Then, select [File]→[Close Workspace].
In the PM + menu, select [File]→[Exit PM +].
PM + ends.
- 75 -
4 Hardware Specifications
In this chapter, the hardware of TK-RF8058+SB will be explained.
Microcontroller
Clock
Interface
Power supply
voltage
Input/output for
operation check
use
Other hardware
μPD78F8058
CPU main system clock：
20/8/1MHz (Internal oscillator)
16/8/4/2/1MHz (Generated from the
32MHz main clock)
CPU subsystem clock：32.768KHz
USB connector(MiniB)
Extension connector(CN1: not mounted)
External Power Supply Terminals
（J2,J3）
MINICUBE2 connector(FP1)
USB Power: 5.0V
One AA battery: 1.5V
Two AA batteries: 3.0V
External Power Supply at J2 and J3: 1.8V
- 3.6V
・LED x3 : Only LED1 is connected to the
MB-RF8058 module.
・Push switch x3: Only SW1 is connected
・Dip switch (SW4)
・Reset switch (SW7)
・Temperature sensor (U1: not used)
・Illminance sensor (Q1: not used)
・7LED x3
・Power LED(LED4)
・Voltage regulation selection by SW5 to
3.0V, 2.0V, or 1.8V
- 76 -
4.1
Layout of hardware functions
JP3
J2
JP5 SW4 SW7 CN1
JP2
J3
USB1
SW1, 2, 3
JP4
SW5 SW6 JP2JP1
- 77 -
JP4
FP1
LED1, 2, 3
4.2
Hardware Functions
4.2.1 SW4 (Dip Switch)
Mode setting
1 bit
2 bit ALL ON → USB TK debugger
3 bit ALL OFF → PC HyperTerminal mode
4 bit
5 bit Pull-up for RESET terminal(ON)／ no pull-up (OFF)
6 bit Power LED ON/OFF
7 bit Not used (TP2)
8 bit Not used (TP3)
4.2.2 SW5
Selection of the regulator
1.8V 1.8V output to the module
2.0V 2.0V output to the module
3.0V 3.0V output to the module
Caution) Never alter the SW5 settings while a power source is being
applied.
The regulator chip may be destroyed.
Alter the SW5 settings after the SW3 jumper pin is removed.
4.2.3 SW6
Serial Communication Mode Setting
K0R-K0USB
UART- USB for HyperTerminal
Debug/Writer For ID78K0R-QB or WriteEZ5
4.2.4 JP1
Power supply to peripheral circuits such as LEDs and the temp sensor.
4.2.5 JP2
Selection of a power source
1-2 short-circuit Regulation output of 1.8V, 2.0V, or 3.0V
2-3 short-circuit No regulation from two batteries or the external power source
- 78 -
4.2.6 JP3
Selection of a power source to the regulator
1-2 USB
2-3 Battery
4.2.7 JP4
A jumper to measure a consumed current on the module.
If you don’t execute measurement, please keep short-circuited.
If you measure a consumed current to the module, please use external power
supply or two batteries for precision measurement.
4.2.8 JP5
A selection of one battery or two batteries.
1-2 One battery
2-3 Two batteries
4.2.9 SW1,SW2,SW3
SW3 and SW4 are tact switches. The port inputs are short-circuited to ground,
while they are being pushed, and kept open otherwise. Therefore please set the
on-chip pull-up registors(PU1) during initializing routine of your program code.
(For more detail, please refer to the User’s manual of the μPD 78F8058CPU.)
Connected MCU pin
Note
SW1 P15/RTCDIV/RTCCL/GPIO2 GPIO2 belongs to the RF part
SW2 Not connected
SW3 Not Connected
4.2.10 SW7
SW7 is the reset switch. CPU can be reset by pushing.
- 79 -
4.2.11 LED4
LED4 indicates if power is being applied to the board, if SW4-5 is on.
If you want to save power by turning the LED4 off, please set SW4-5 to off.
4.2.12 LED1, LED2, and LED3
LED1, LED2, and LED3 are available for applications. To make an LED on,
please set the output port LOW.
Connection of LED1, LED2, and LED3
Connected MCU pin
Note
LED1 P16/TI01/TO01/INTP5/GPIO3 GPIO2 belongs to the RF part
LED2 Not connected
LED3 Not connected
4.2.13 FP1
The connector for MINICUBE2.
Please set the side switches of MINICUBE2 to “M1” and “T”.
4.2.14 J2 and J3
J2 and J3 is a pair of terminals to input power supply from an external power
source. The accepted range of power source is from 1.8V to 3.6V.
4.3
Summary of Power Supply Settings
Summary of power supply settings
USB Power
An external
source
At J2 and J3
Two batteries
One battery
JP3
1-2 connected
(USB)
Any
1-2 connected
(USB)
2-3 connected (Battery)
JP5
Any
1-2 connected
(1Cell)
2-3 connected
(2Cells)
1-2 connected (1Cell)
JP2
1-2 connected
(Regulator)
2-3 connected (Battery or External)
- 80 -
1-2connected
(Regulator)
4.4
Solder-short pad
The solder-short pad offers a way to modify the circuit on the module.
The solder-short pad looks like the picture below.
To open it, please cut the narrow part by a knife. To connect them back, please
form a solder bridge on the pad.
Solder-short pad
(Open)
Solder-short pad
name
Solder-short pad
(Short)
Factory
default
Connection
Connection between
P16/TI01/TO01/INTP5/GPIO3 and LED1
S_LED1
Short
S_LED2
Short
S_LED3
Short
S_SW1
Short
S_SW2
Short
S_SW3
Short
AD1
Short
AD2
Short
SCK
Open
Not used
SI
Open
Not used
SO
Open
Not used
Connection to LED2
No connection to the MB-RF8058 board.
Connection to LED3
No connection to the MB-RF8058 board
Connection from SW1
Connection from SW2
No connection to the MB-RF8058 board
Connection from SW3
No connection to the MB-RF8058 board
Analogue output from the temperature sensor
No connection to the MB-RF8058 board
Analogue output from the illumination sensor
No connection to the MB-RF8058 board
- 81 -
5 Troubleshooting
This chapter describes how to solve troubles you may face.
5.1
If you cannot find USB driver when you connect PC to the kit
Check Point 1
If you use USB hub, do not use it. (USB hub is not supported)
Check Point 2
Check if you installed "Starter Kit USB Driver" in "1.2 Installation of Development
Tools". If not, install the driver.
Check Point 3
Check if the settings of the switch on the kit are correct with referring to "1.3
Installation of USB Driver".
Check Point 4
If above 3 check points are confirmed, disconnect the USB cable from PC and
re-connect again. It should show the "Found New Hardware Wizard" wizard. Operate
the installation with referring to "1.3 Installation of USB Driver". After the installation,
make sure you go through "1.3.3 Completion of USB Driver Installation" to confirm the
USB driver installation.
5.2
Error when you start the debugger
There could be several reasons to make errors happen.
The solving processes differ depending on errors. Please check the error message first.
The solving processes for each error are as follows.
- 82 -
5.2.1 "Can not communicate with Emulator..." (F0100 or A0109)
Check Point 1
If you use USB hub, do not use it. (USB hub is not supported)
Check Point 2
Check if the settings of the switch on the kit are correct with referring "1.3 Installation
of USB Driver".
Check Point 3
Confirm the USB driver installation with referring to "1.3.3 Completion of USB Driver
Installation".
Check Point 4
If above 3 check points are confirmed, close the debugger and disconnect the USB
cable from PC. Re-connect USB cable properly to both the PC and the kit, and then
re-start the debugger.
5.2.2 "Incorrect ID Code." (Ff603)
This error occurs when the security ID stored on microcontroller built-in flash memory is
different from the ID code you entered at the start of debugger.
Security ID entry area at the start of debugger
Check Point 1
Enter correct security ID and click OK on the configuration window.
Check Point 2
If you forgot the security ID, you have to erase the microcontroller built-in flash
memory. Before erasing, check if you actually set the security ID with referring to
"3.4Configuration of Linker Option". Also remember the code you set for the security
ID.
After this, erase the flash memory with referring to "6.4Erase of flash memory".
- 83 -
5.2.3 "The on-chip debug function had been disabled in the device."
(F0c79)
This error occurs when the value at address C3H (On-chip debug option byte) in
microcontroller built-in flash memory is incorrect. You need to erase the flash memory.
Check Point 1
Check if you actually set the correct on-chip debug option byte with referring to
"3.4Configuration of Linker Option". If it is not correct, then set correctly.
Check Point 2
Erase the flash memory with referring to "6.4Erase of flash memory".
5.2.4 "Disabling the on-chip debug function is prohibited." (F0c33)
Basically, this error occurs when you start (download) the debugger without doing the
settings described at "3.4Configuration of Linker Option". Do the same checking processes
as"4.2.3 The on-chip debug function had been disabled in the device. (F0c79)".
- 84 -
6 Other Information
This chapter explains some useful operation techniques of development tools and
circuit diagram of the kit for developing of user programs.
7.1 Create a new workspace (project)
7.2 Register additional source file
7.3 Debugger tips
7.4 Erase microcontroller built-in flash memory
7.5 Circuit diagram
- 85 -
6.1
Create a new workspace
Now, create a new workspace and project.
PM+ allows you to create a new workspace with following "New WorkSpace"
dialog.
Select "File" on PM+ menu bar, then "New Workspace...".
"New WorkSpace" dialog
opens

Workspace File Name:
-> Specify the name of the workspace file that
manages the project files.
.prw is automatically suffixed as the file type.
A project file (.prj) of the same name is
simultaneously created.
Folder:
-> Specify the folder for saving the workspace file by
writing its absolute path.
This item can be selected from a reference
dialog box by pressing the Browse… button.
Project Group Name:
-> Specify this item if wishing to manage
multiple projects together in function units.
If nothing is specified, this item is the same as
the workspace file name.
Microcontroller Name:
-> Specify the name of the microcontroller to be
used.
Device Name:
-> Specify the name of the device to be used.
The concrete information set here is
described on the following pages
- 86 -
Input the workspace information setting
as follows.
Workspace file name
→ test
Folder
→ C:¥TK78K0R
Project Group Name
→ (no input)
Microcontroller Name
→ 78K0R
Device Name
→ uPD78F8058
Click
Click
Yes
Next >
button
button
Click
- 87 -
Detail Setting
button
Set the version of tools as
follows.
CC78K0R：W2.12
RA78K0R：W1.33
ID78K0R-QB：V3.60
Select tools as above screenshot, then click
Click
Next >
- 88 -
OK
Click
Next >
Select ID78K0R-QB V3.60
Click
Next >
Check the project information
settings
Click
- 89 -
Finish
Project “test" was registered.
This completes workspace and project creation.
Additional source files can be registered at any time thereafter.
For details, refer to "7.2 Register additional source file".
Also, you need to do the settings for on-chip debug. Please refer to "3.4 Set
Linker Options", "3.5 Set Compiler Options", and "3.7 Check Debugger Settings".
- 90 -
6.2
Registration of new source files
Now, we learn how to register new source files.
The following example shows how to register two additional source files of “b.c”
and “c.c” with source file “a.c” already registered.
Place the cursor on a source file in the Project window of PM+, and select [Add
Source Files…] displayed in the right-click menu.
Select source files "b.c" and
"c.c", then click Open
Multiple source files can be selected by clicking them while keep pressing
- 91 -
Ctrl
key.
Source files "b.c"
and "c.c" are added
to the project.
- 92 -
6.3
Debugger tips
This section describes some useful techniques for the debugger (ID78K0R-QB).
6.3.1 Change display of buttons
Execution controls (run, stop, step-in debugging, reset, etc) and opening
functional window can be made by below buttons. However, it could be difficult
to know which button does what.
In this case, select "Options" on menu bar, then "Debugger Options". Check
"Pictures and Text" on setting area.
With this setting, the buttons display the text as well, so that it is easier to know
what they are.
6.3.2 Display source list and function list
When you wish to see source file list or function list, select "Browse" on menu
bar, then "Other" -> "List" to open the list window. The information in the
windows is synchronized. Therefore, it is not just for referring to the list, but it is
useful when you wish to update files or functions.
When you click "game1"...
Source window shows "game1"
- 93 -
6.3.3 Set/delete breakpoints
Breakpoints are executed by clicking lines in which " * " is displayed
"B" is displayed in the line where a breakpoint is set.
Breakpoints are deleted by clicking "B".
Click
Breakpoint was set
- 94 -
6.3.4 Display global variables
With using Watch Window, you can display global variables. There are several
ways to register global variables to watch window. In this section, how to
register from source window is described.
①Right-click the variable on source window, then select "Add Watch..."
②Add Watch dialog opens. Click
OK
③Adding a variable to watch window is completed.
- 95 -
6.3.5 Display global variables while programs are running
RAM, general-purpose register, and SFR can be referred by the pseudo
real-time monitor function even when the programs are running.
Select "Option" on menu bar, then "Extended Option...". Configure the settings
for "RAM Monitor And DMM".
Check
Specify the sampling interval time of the pseudo real-time monitor function.
The sampling time can be specified from 0 to 65500 with unit of 100ms.
It will not monitor if it is set to "0" or blank.
This completes the settings.
Note:
・ The user program momentarily breaks upon a read.
・ Do not use the pseudo real-time monitor function while using the memory
window. It uses the system resources significantly as it monitors the
displaying memory as well.
・ It is recommended to close the memory window when you use the pseudo
real-time monitor function.
- 96 -
6.3.6 Display local variables
Local variable window is used to display local variables.
By clicking the button below, you can open the local variable window.
Unlike global variables, local variables cannot be displayed when programs are
running.
6.3.7 Display memory and SFR contents
By clicking the button below, you can open the memory window.
By clicking the button below, you can open the SFR window.
- 97 -
6.4
Erase of flash memory
If the On-Chip Debug Option Byte is set to "Do not erase data of flash memory in
case of failures in enabling on-chip debugging" and if you forget the security ID,
you need to erase the flash memory completely.
Ｔo erase the flash memory, please follow the steps below.
WriteEZ5 is installed at "1.2.2 Installation of Development Tools".
①
Start WriteEZ5 by selecting "Windows Start" menu, "Programs", "NEC Electronics Tools",
"WriteEZ5", "V1.00", and "WriteEZ5".
- 98 -
②
The switch of TK-RF8058+SB is set as follows.
ON
ON
ON
SW4 setting
ON
ON
ON
OFF
OFF
JP5：Any
JP3：
1-2 short (USB)
SW5：3.0V
SW6：
「Debug/Writer」
JP2：
JP1：short
JP4：short
1-2 short(Regulator)
③
Then, please connect the “USB1” connector on the TK-RF8058+SB board with the USB
connector of your PC.
- 99 -
④
Push the「Setup」button.
⑤
Push the「PRM File Read」button.
- 100 -
⑥
Please select “78F8058.prm” in the directory of “¥PRM” in the CD-ROM.
⑦
"Port" selects the COM port number where TK-RF8058+SB is allocated.
＊Only the COM port number that the personal computer has is displayed in this pulldown menu.
- 101 -
⑧
"Erase" The deletion of the flash memory begins when the button is pushed.
⑨
If Flash EEPROM has been erased successfully, “chip erase finish” will be displayed as
shown below.
- 102 -
※ ID Code
The ID Code is a mechanism to prevent an unwelcome third party from accessing your
source code by initiating the debugger. Therefore, it is recommended to modify the ID Code
from the default value to secure your original source code. However, once you modify it, then,
if you forget the security ID or mistakenly over-write 0x00(value) to the address of 0xC3, the
debugger ID78K0R-QB is unable to access to the CPU via OCD interface. In this case, you
have to start over from erasing all data in the Flash EEPROM. Then, you can define the new
ID Code. You may load your source code from the debugger with a load module file.
- 103 -
6.5
BOM List, Circuit diagram & Pin Connection
Here is the BOM List, circuit diagram & Pin Connection of the evaluation kit.
● SB-UD board BOM list
No.
Mount Quantity
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Mount Parts Reference
Unmount Parts Reference
S_SW1,S_LED1,A/D1,S_SW2,
S_LED2,A/D2,S_SW3,S_LED3
SO,SI,SCK
BT1,BT2
CN1
CN2
C1
C2
C3
C6,C7,C11,C12,C13,
C14,C15,C16
C10,C8
C9
FP1
JP1,JP4
JP2,JP3,JP5
J1
J2
J3
LED1,LED2,LED3
LED4
L1
L2
MR1
C4,C5
P2,P1
Q1
R1,R44
R2,R3,R4,
R32,R33,R38,R42,R45
R5
R7,R8
R16
R17
R18
R20,R21
R22
R27,R34,R37,R43
R39,R40
R6,R35,R36,R41
R24,R25,R26,R28
R29,R31
R30
SW1,SW2,SW3,SW7
SW4
SW6,SW5
TPU1,TPU2,TPU3,TPU4,TPU5,
TPU6,TPU7,TPU8,TPU9
TP1,TP2,TP3,TP4,TP5
USB1
U1
U2
U5
U6
U7
U8
U9
Y1
JP1,JP2,JP3,JP4,JP5
U3
U4
R9,R10,R12,R13,R14,
R15,R19
R11,R23,R46
- 104 -
Type
Short Pad
Parts No
SS
Short Pad
Batt case
Connecter
Connecter
Chip ceramic cap
Tantal cap
Chip ceramic cap
Chip ceramic cap
SO
2460
HIF3H-50DA-2.54DSA
HIF3H-20DA-2.54DSA
2.2uF
F931A476MCC
10uF
0.1uF
Chip ceramic cap
Aluminum Electrolytic Cap
Connecter
Connecter
Connecter
Connecter
Terminal
Terminal
LED
LED
inductor
Filter
resister module
Connecter
IC
Chip resister
Chip resister
0.47uF
4.7uF/25V
HIF3FC-16PA-2.54DSA
FFC-2AMEP1
FFC-3AMEP1
DF17(3.0)-60DS-0.5V(57)
T-16-Red
T-16-Black
SML-311UTT86
PG1112H
CDRH5D28NP-8R2NC
BLM41PG750S
CN1E4K-105J
XR2C-1011N
TPS851
120
1.5K
Chip resister
Chip resister
Chip resister
Chip resister
Chip resister
Chip resister
Chip resister
Chip resister
Chip resister
Chip resister
Chip resister
Switch
Switch
Switch
Trough hole
7.5K
390K
487K
562K
909K
187K
182K
100K
27
10K
100
SKQMBB
CHS-08B
SSSS223600
TPU
Terminal
Connecter
IC
IC
IC
IC
IC
IC
IC
IC
IC
Jumper
Chip resister
LC-2
UX60A-MB-5ST
S-8120CNB
TPS61020DRC
SN74LVC3G07DCT
SN74LVC2G125DCU
SN74LVC2G07DCK
UPD78F0730MC
SN74LVC1G125DCK
SN74LVC2T45DCU
CSTCE16M0V53-R0
HIF3GA-2.54SP
Chip resister
Maker
Note
KEYSTONE
HIROSE
HIROSE
NICHICON
HIROSE
HONDA
HONDA
HIROSE
SATO PARTS
SATO PARTS
STANLY
ROHM
Sumida
MURATA
KOA
OMRON
TOSHIBA
for A&D
ALPS
COPAL
ALPS
MAC8
HIROSE
SII
TI
TI
TI
TI
NECEL
TI
TI
MURATA
HIROSE
For SIO I/F
For K0R
For K0R
● MB-RF8058 board BOM list
No.
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Mount Quantity
Mount Parts Reference
CN1
C2,C5,C6,C11,C15
C4,C7,C10,C16
C8,C18
C9
C12
C24,C13
C14,C1,C3
C17
C19
C23,C20
C21
C22
F1
J1
L1
L2
Unmount Parts Reference
L3,L4
R1
R2,R4,R5,R7,R8,R9,R10
R3
R6
TP1,TP2,TP3,TP4
U1
VDD_R,VDD
Y1
Y2
Type
Connecter
Chip ceramic cap
Chip ceramic cap
Chip ceramic cap
Chip ceramic cap
Chip resister
Chip ceramic cap
Chip ceramic cap
Chip ceramic cap
Chip ceramic cap
Chip ceramic cap
Chip ceramic cap
Chip ceramic cap
Filter
Connecter
inductor
inductor
inductor
Chip resister
Chip resister
Chip resister
Chip resister
Check Pin
IC
Short pad
Resonator
Resonator
- 105 -
Parts No
901-144-8RFX
47pF
0.01uF
1uF
39pF
0.1uF
10pF
0.47uF
4.7uF/10V
10uF/10V
3pF
4pF
LDB212G4020C-001
DF17(2.0)-060DP-0.5V(57)
LQG15HN3N9S02
LQH2MCN8R2M02
Manufacturer
AMPHENOL
MURATA
HIROSE
Murata
MURATA
1M
10K
LC-33
uPD78F8058
SS
NX3225SA-32.000M-STD-CSR-3
SSP-T7-FL 3.7pF
NECEL
NDK
SII
2
IOVDD
- 106 -
2460
GND
VDD
2460
R1
120
3V
T-16-Black
J3A
T-16-Red
J2A
JP5
S_LED1
IOVDD
LED2
JP3
FFC-3AMEP1
EXTVDD
USBVDD
10uF
C3
R8
390K
R7
390K
1V
8.2uH
L1
S_LED2
LED3
11
13
15
17
19
CN2
10
12
14
16
18
20
G_PAD
PGND
LBO
FB
VOUT
R20
187K
R16
487K
11
10
R6
1.5K
R21
187K
R17
562K
IOVDD
TP1
LC-2
R22
182K
R18
909K
SW1
CHS-08B
SW4-8
CHS-08B
A/D1
TOOL0
RESET
FLMD0
RxD_MCU
C2
A/D1
47uF
2.2uF
1pin
: 3.0V
Center : 2.0V
4pin
: 1.8V
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
JP2
TP4
LC-2
GND
U1
FFC-2AMEP1
JP4
VDD
IOVDD
IOVDD
FFC-2AMEP1
JP1
TP5
LC-2
VDD
xxx
xxx
R23
R11
A/D2
TxD_MCU
I/O_01
I/O_03
LED1
P_SW2
A/D2
LED3
I/O_04
I/O_06
I/O_08
I/O_10
I/O_12
I/O_14
I/O_16
I/O_18
I/O_20
I/O_22
I/O_24
I/O_26
I/O_28
I/O_30
I/O_32
I/O_34
I/O_36
I/O_38
I/O_40
TOOL1
xxx
xxx
xxx
xxx
A/D2
R14
R13
R10
R9
TxD_MCU
TOOL1
R19
xxx
T_RESET
R15
R12
R5
7.5K
Date:
Size
A3
Title
VDD
I/O_01
I/O_02
I/O_03
P_SW1
P_SW2
P_SW3
I/O_03
I/O_02
I/O_01
TxD_MCU
SO
SI
SCK
10
10
11
13
15
SO_MCU
SI_MCU
SCK_MCU
Monday , September 14, 2009
Sheet
HIF3FC-16PA-2.54DSA
10
12
14
16
of
FLMD0
RESET
11.VDD
12.SCK10
13.SI10(/RxD1)
14.SO10(/TxD1)
15.P13/TxD3
16.GND
17.P75/KR5/INTP10
18.P76/KR6/INTP11
19.P77/KR7/INTP12
20.GND
XR2C-1011N
P2
GND
RES
SI
VDD
SO
10
11
12
13
FL0
RESET_IN CLK_IN
FP1
Document Number
TS-TCS00327
SB-UD
1.VDD
2.FLMD0
3.RESET
4.P41/TOOL1
5.P40/TOOL0
6.GND
7.P30/INT3
8.P74/KR4/INTP8
9.P14/RxD3
10.GND
XR2C-1011N
P1
MINICUBE2
MINICUBE2
I/FI/F IOVDD
Illuminance Sensor
xxx
xxx
VDD
FLMD0
RESET
TOOL1
TOOL0
LED1
LED2
RxD_MCU
Q1
TPS851
IOVDD
126 Parts, 33 Library Parts, 136 Nets, 490 Pins
VDD
TOOL1
TOOL0
TxD_MCU
RxD_MCU
Current Measure
S-8120CNB
VSS
VOUT VDD
NC
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
DF17(3.0)-60DS-0.5V(57)
J1
Temp. Sensor
FFC-3AMEP1
VDD
TOOL0
RESET
FLMD1
RxD_MCU
I/O_02
P_SW1
A/D1
LED2
P_SW3
A/D3
I/O_05
I/O_07
I/O_09
I/O_11
I/O_13
I/O_15
I/O_17
I/O_19
I/O_21
I/O_23
I/O_25
I/O_27
I/O_29
I/O_31
I/O_33
I/O_35
I/O_37
I/O_39
VDD
1-2 : Regulator
2-3 : Battery or External
10
SW4-7
C1
SKQMBB
SW3
SKQMBB
SW2
SKQMBB
SW5
SSSS223600
S_SW3
S_SW2
TP3
LC-2
TP2
LC-2
S_SW1
USBVDD
8 6 5 4 2 1
P_SW3
P_SW2
P_SW1
EXTVDD
I/O_32
I/O_34
I/O_36
I/O_38
I/O_40
LED3
SML-311UTT86
R4
1.5K
TPS61020DRC
GND
PS
LBI
EN
VBAT
SW
U2
S_LED3
IOVDD
No Mount
HIF3H-20DA-2.54DSA
LED2
SML-311UTT86
R3
1.5K
EXTVDD
I/O_31
I/O_33
I/O_35
I/O_37
I/O_39
IOVDD
USBVDD
LED1
SML-311UTT86
R2
1.5K
TxD_MCU
I/O_01
I/O_03
LED1
P_SW2
A/D2
LED3
I/O_04
I/O_06
I/O_08
I/O_10
I/O_12
I/O_14
I/O_16
I/O_18
I/O_20
I/O_22
I/O_24
I/O_26
I/O_28
I/O_30
TOOL1
Regulator Input
1-2 : USB
2-3 : Battery
LED1
No Mount
: 1Cell
: 2Cell
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
HIF3H-50DA-2.54DSA
FFC-3AMEP1
1.5V
1-2
2-3
POWER
LED4
PG1112H
BT1
BT2
TOOL0
T_RESET
FLMD1
RxD_MCU
I/O_02
P_SW1
A/D1
LED2
P_SW3
A/D3
I/O_05
I/O_07
I/O_09
I/O_11
I/O_13
I/O_15
I/O_17
I/O_19
I/O_21
I/O_23
I/O_25
I/O_27
I/O_29
SW4-6
CHS-08B
T_RESET
11
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
CN1
VDD
Rev
1.0
● SB-UD board schematic
0.1uF
C16
GND
ID_NC
DD+
VBUS
USB1
UX60A-MB-5ST
SW7
SKQMBB
RESET SW
R46
L2
USBVDD
R44
120
1.5K
R45
SW4-5
CHS-08B
IOVDD
BLM41PG750S
C9
4.7uF/25V
T_RESET
R42
T_RESET
RESET
TOOL1
1.5K
C7
0.1uF
IOVDD
C5
0.1uF
IOVDD
U4A
C10
R39
R40
13
CHS-08B
SW4-4
TPU4 TPU5
1.5K
C13
SN74LVC2T45DCU
A2
A1
DIR
VCCA
U9
GND B2
B1
VCCB
USBVDD
C15
0.1uF
USBVDD
PD5
PD6
17
16
18
19
20
21
22
23
24
25
R38
MR1
1.5K
100K
IOVDD
PD5
PD6
PD1
10K
R41
USBVDD
SO_MCU
SI_MCU
RxD6USB
Date:
Size
A3
Title
TxD6USB
Monday , September 14, 2009
Document Number
TS-TCS00327
SB-UD
SW6
↓Debug/Writer
↑K0R<-->K0USB
SSSS223600
14
SW4-3
CHS-08B
TPU8 TPU9
TxD6USB
16
SW4-1
USBVDD
R33
1.5K
TOOL1_SW
IOVDD
SN74LVC2G07DCK
U6B
TPU6 TPU7
SN74LVC2G125DCU
U5B
IOVDD
Mounted only 78K0.
27
R30
15
SW4-2
CHS-08B
FLMD0
TOOL0
TxD_MCU
RxD_MCU
RESET
C6
0.1uF
IOVDD
Sheet
Mounted only 78K0.
Mounted only 78K0.
SN74LVC2G125DCU
U5A
SCK_MCU
SN74LVC2G125DCU
CHS-08B
IOVDD
IOVDD
U4B
IOVDD
1.5K
IOVDD
1.5K
R24
R26
SN74LVC3G07DCT
U3C
100K
R37
SN74LVC3G07DCT
U3A
R34
IOVDD
FLMD0U
(Shield)
IOVDD
CN1E4K-105J
TPU3
TPU1
TPU2
26
R31
100K
Mounted only 78K0.
27
100K
R29
100K
R27
Mounted only 78K0.
29
C12
0.1uF
U3B
SN74LVC3G07DCT
IOVDD
28
USBVDD
P61
P60
P32/INTP3/OCD1B
P31/INTP2/OCD1A
EVdd
EVss
P33/TI51/TO51
P17/TI50/TO50
UPD78F0730MC
C14
0.1uF
IOVDD
Mounted expect 78K0.
RxD6USB
IOVDD
C11
0.1uF
TOOL1_SW
100K
R43
IOVDD
0.1uF
USBPUC
USBM
USBP
USBREGC
Vdd
Vss
REGC
P121/X1/OCD0A
P16/TOH1
P15
P14/RxD6
P13/TxD6
P12/SO10
P11/SI10
P10/SCK10
30
1.5K
R25
USBVDD
C4
0.1uF
P122/X2/EXCLK/OCD0B
FLMD0
RESET
P120/INTP0/EXLVI
P00/TI000
P01/TI010/TO00
P30/INTP1
U7
USBVDD
15
14
13
27
27
11
10
12
PD1
0.47uF
0.47uF
10K
FLMD0U
10K
CSTCE16M0V53-R0
Y1
C8
SN74LVC1G125DCK
U8
R35
R36
SN74LVC2G07DCK
U6A
R32
1.5K
R28
Mounted only 78K0.
USBVDD
Mounted only 78K0.
SN74LVC2G125DCU
USBVDD
IOVDD
USBVDD
IOVDD
FG4
FG3
FG2
FG1
FG4
FG3
FG2
FG1
RxD6USB
Mounted only SIO.
IOVDD
Mounted only 78K0.
12
- 107 -
of
Rev
1.0
RxD
SI/RxD
SW1
A/D1(Temp)
LED2
SW3
A/D3
P130P11P17P76
GPIO0
SCAN_MODE
I2CSEL
TOOL0
RESET
FLMD0
P14
P03
P15
VDD
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
J1
SMA
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
P120
P12P10P31P121
GPIO1
SCAN_EN
P144-
P13
P02
P04
P16
TOOL1
L3
xxx
DF17(2.0)-060DP-0.5V(57)
CN1
L4
xxx
TxD
SO/TxD
SCK
LED1
SW2
A/D2(Illumi)
LED3
C12
C23
10uF/10V
C14
10pF
VDD
C18
1uF
BAL
C19
4.7uF/10V
VDD
xxx
R6
L1
3.9nH
VDD_R
BAL
GND GND
LDB212G4020C-001
NC
UNB
F1
VDD_RF
VDD_RF
VDD_R
C20 +
10uF/10V
VDD_R
8.2uH
TP2
LC-33
L2
C13
0.1uF
C11
47pF
VDD_R
TP5
LC-33
R7
10K
56
P14
C9
39pF
C8
1uF
TP6
LC-33
uPD78F8058
GND_pad
P14/RxD3
P15(/GPIO2)
INT
P16(/GPIO3)
RESETn
C2
47pF
VDD_RF
VDD_3V(/AVDD)
VDD_2V2
GPIO1
GPIO0
GND_GR
VDD_GR
VDD_RF2
RF_N
RF_P
VDD_RF1
U1
VDD_M
57
55
54
53
52
51
50
49
48
47
46
45
44
43
42
P15
P16
GPIO1
GPIO0
C15
47pF
VDD_RF
TP4
LC-33
VDD_R
VDD_R
C10
0.01uF
VDD_RF
C4
0.01uF
VDD_RF
41
LOOP_C
P13
39
VDD_CP
38
GND_PLL
P12-
P13/TxD3
40
VDD_VCO
(SI/P12/SC00)
(SO/P11/SI00)
P11-
(SCLK/P10/SCK00)
37
VDD_PLL
P10-
36
XTAL_P
WAKE
35
VDD_RF
R1
1M
C5
47pF
VDD_R
C6
47pF
C1
VDD_D
P40/TOOL0
RESET
P124/XT2
P123/XT1
FLMD0
P122/X2/EXCLK
P121/X1
REGC
VSS
VDD
P31/TI03/TO03/INTP4
P76/INTP10
10pF
TOOL0
Date:
Size
A3
Title
R5
10K
RESET
15
FLMD0
P121
P31-
P76
VDD
R4
10K
VDD_M
R10
10K
TP3
C21
3pF
R3
0.47uF
Sheet
VDD_M
C17
TP1
VDD LC-33
Friday , September 11, 2009
Document Number
TS-TCS00326
R9
10K
C24
0.1uF
VDD_M
R8
10K
LC-33
MB-RF8058
VDD_M
C16
0.01uF
VDD_RF
10pF
16
17
18
19
20
21
22
23
24
25
26
27
C3
R2
10K
C7
0.01uF
45 Parts, 12 Library Parts, 44 Nets, 177 Pins
Y1
NX3225SA-32.000M-STD-CSR-3
(SEN/P17)
P17-
34
VDD_A
XTAL_N
SCAN_MODE
P130-
AVSS
33
VDD_BG
P04
P130
32
CLK_OUT
10
P02/SO10/TxD1
11
P03
P04/SCK1
31
SCAN_MODE
P02
P144
12
P144-
P03/SI10/RxD1
SCAN_EN
30
SCAN_EN
28
GND_D
I2CSEL
29
I2CSEL
P120
13
P41/TOOL1
14
P120
- 108 TOOL1
VDD_RF
of
C22
4pF
Rev
1.0
Y2
SSP-T7-FL 3.7pF
● MB-RF8058 board schematic
●
SB-UD board CN1 Pin connecting list
Pin number
10
11
12
13
14
Net name
VDD
GND
VDD
GND
TOOL0
TOOL1
T_RESET
GND
FLMD1
TxD_MCU
RxD_MCU
I/O_01
I/O_02
I/O_03
uPD78F8058 Signal Port Connection
P13/TxD3
P14/RxD3
P02/SO10/TxD1
P03/SI10/RxD1/SDA10
P04/SCK10/SCL10
15
P_SW1
P15/RTCDIV/RTCCL/GPIO2
16
LED1
P16/TI01/TO01/INTP5/GPIO3
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
A/D1
P_SW2
LED2
A/D2
P_SW3
LED3
A/D3
I/O_04
I/O_05
I/O_06
I/O_07
I/O_08
I/O_09
I/O_10
I/O_11
I/O_12
I/O_13
I/O_14
I/O_15
I/O_16
I/O_17
I/O_18
I/O_19
I/O_20
I/O_21
I/O_22
I/O_23
I/O_24
I/O_25
I/O_26
I/O_27
I/O_28
I/O_29
I/O_30
P120/INTP0/EXLVI
P76/INTP10
P121/X1
GPIO0
GPIO1
Requirement for using the signal
Don't use the USB connection as debugging or
serial communication when you use this signal.
Separate a switch with cutting the solder short pad
for use as general-purpose port.
Separate a LED with cutting the solder short pad
for use as general-purpose port.
This port has a pull-up resister.
RF transceiver port
RF transceiver port
- 109 -
7 Mode setting of the board
The combination table of the switch of this board is shown.
JP3
JP5 SW4
JP2
JP4
SW5 SW6 JP2JP1
Mode Setting Table
User mode on USB power with
Debugging and Flash programming
with MINICUBE2, and UART-USB
conversion to a HyperTerminal. (NOTE)
(Dip switch)
1-4 → ALL OFF
SW4
5 → ON (Pull-up the RESET pin)
6 → ON (Power LED on)
7,8 → Any
SW6 「K0R-K0USB」
JP4
Debug/Flash programming mode
via USB without MINICUBE2
using ID78K0R-QB/WriteEZ5
(Dip switch)
1-6 → ALL ON
7,8 → Any
「Debug/Writer」
SW5 1.8V, 2.0V or 3.0V
1.8V, 2.0V or 3.0V
JP3 1-2 (USB) short
1-2 (USB) short
JP5 Any
Any
JP2 1-2 short
1-2 short
JP1 short
short
JP4 short
short
(NOTE): The side switches of MINICUBE2 have to be set to “M1” and “T”.
- 110 -
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Elements 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2010:03:23 18:51:15+09:00
Create Date                     : 2010:03:23 18:51:15+09:00
Format                          : application/pdf
Title                           : Microsoft Word - TK-RF8058+SB_UM_E.doc
Creator                         : remote
Document ID                     : uuid:26a75e43-c109-4428-a3e7-aa9803c4899b
Instance ID                     : uuid:056864cf-d5ad-47e7-915e-03edd10b8550
Page Count                      : 110
Author                          : remote
EXIF Metadata provided by EXIF.tools
FCC ID Filing: X8U0001

Navigation menu