THALES DIS AlS Deutschland TC65 Quadband GSM/GPRS Module User Manual TC65

Download:
Mirror Download [FCC.gov]
Document ID	550088
Application ID	4gQcNUkPAlZ5H3XJLHS/eg==
Document Description	Users Manual 2 of 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	218.82kB (2735189 bits)
Date Submitted	2005-06-10 00:00:00
Date Available	2005-06-10 00:00:00
Creation Date	2005-06-10 20:07:57
Producing Software	Acrobat Distiller 6.0.1 (Windows)
Document Lastmod	2005-06-10 20:08:21
Document Title	TC65
Document Creator	Acrobat PDFMaker 6.0 for Word
Document Author:	DE18D000

TC65 Hardware Interface Description
Strictly confidential / Draft
3.11.1
Installing the USB Modem Driver
This section assumes you are familiar with installing and configuring a modem under
Windows 2000 and Windows XP. As both operating systems use multiple methods to access
modem settings this section provides only a brief summary of the most important steps.
Take care that the “usbmodem.inf” file delivered with TC65 is at hand. Connect the USB
cable to the TC65 host application (for example the evaluation board DSB75) and the PC.
Windows detects TC65 as a new USB modem, opens the Found New Hardware Wizard and
reports that it is searching for the “Siemens AG WM USB Modem” driver. Follow the
instructions on the screen and specify the path where the “usbmodem.inf” file is located.
Windows will copy the required software to your computer and configure the modem by
assigning a free COM port. If you are already using more than one COM port then the next
free one will be allocated. Click Finish to complete the installation.
Notes for Windows 2000 only:
• During the installation procedure you will be prompted for the “usbser.sys” driver. Make
sure the file is present before you start installing the above inf file.
The “usbser.sys” file is not delivered as a single file, but must be extracted from a
Windows 2000 cabinet file. This is either the file “driver.cab” located in the “I386” folder of
the original Windows 2000 CD or a later cabinet file inside the Service Pack. SP4 for
example includes the “sp4.cab” file which can be found in its “I386” folder. The
“usbser.sys” driver from the Service Pack has priority over one provided with the
standard Windows 2000 install CD.
• It is necessary to restart Windows 2000 to make the changes take effect.
TC65_HD_V00.450
Page 49 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
You can find the “Siemens AG WM
USB Modem” listed under Control
Panel | Phone and Modem Options |
Modems.
Troubleshooting for installation problems
If Windows fails to
assign the next free
COM port to TC65 and,
for example, allocates a
COM port already used
by another modem you
can manually select a
free port as follows:
Open
the
Windows
Device Manager, select
the installed “Siemens
AG WM USB Modem”,
click Properties, select
the Advanced tab and
click Advanced Port
settings.
From
the
listbox
COM
Port
Number choose a free
port. To make the
changes take effect
disconnect
and
reconnect the USB cable.
If not yet successful,
also restart Windows.
TC65_HD_V00.450
Page 50 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
3.12
I2C Interface
I2C is a serial, 8-bit oriented data transfer bus for bit rates up to 400kbps in Fast mode. It
consists of two lines, the serial data line I2CDAT and the serial clock line I2CCLK.
The TC65 module acts as a single master device, e.g. the clock I2CCLK is driven by module.
I2CDAT is a bi-directional line.
Each device connected to the bus is software addressable by a unique 7-bit address, and
simple master/slave relationships exist at all times. The module operates as mastertransmitter or as master-receiver. The customer application transmits or receives data only
on request of the module.
To configure and activate the I2C bus use the AT^SSPI command. If the I2C bus is active the
two lines I2CCLK and I2DAT are locked for use as SPI lines. Vice versa, the activation of the
SPI locks both lines for I2C. Detailed information on the AT^SSPI command as well
explanations on the protocol and syntax required for data transmission can be found in [1].
The I2C interface can be powered from an external supply or via the VEXT line of TC65. If
connected to the VEXT line the I2C interface will be properly shut down when the module
enters the Power-down mode. If you prefer to connect the I2C interface to an external power
supply, take care that VCC of the application is in the range of VVEXT and that the interface is
shut down when the PWR_IND signal goes high. See figures below as well as Section 7 and
Figure 38.
In the application I2CDAT and I2CCLK lines need to be connected to a positive supply
voltage via a pull-up resistor.
For electrical characteristics please refer to Table 17.
Application
GSM module
VCC w VEXT
Rp
I2CDAT
I2CCLK
GND
Rp
I2CDAT
I2CCLK
GND
Figure 15: I2C interface connected to VCC of application
TC65_HD_V00.450
Page 51 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
Application
GSM module
VEXT
Rp
I2CDAT
I2CCLK
GND
Rp
I2CDAT
I2CCLK
GND
Figure 16: I2C interface connected to VEXT line of TC65
Note: Good care should be taken when creating the PCB layout of the host application: The
traces of I2CCLK and I2CDAT should be equal in length and as short as possible.
TC65_HD_V00.450
Page 52 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
3.13
Audio Interfaces
TC65 comprises three audio interfaces available on the board-to-board connector:
• Two analog audio interfaces, both with balanced or single-ended inputs/outputs.
• Serial digital audio interface (DAI) designed for PCM (Pulse Code Modulation).
This means you can connect up to three different audio devices, although only one interface
can be operated at a time. Using the AT^SAIC command you can easily switch back and
forth.
MICP1
MICN1
MUX
MUX
MICP2
MUX
MICN2
Analog switch
EPP1
EPN1
EPP2
EPN2
DSP
Air
Interface
VMIC
AGND
USC0
USC1
USC2
USC3
USC4
Digital
Audio
Interface
USC5
USC6
Figure 17: Audio block diagram
To suit different types of accessories the audio interfaces can be configured for different
audio modes via the AT^SNFS command. The electrical characteristics of the voiceband part
vary with the audio mode. For example, sending and receiving amplification, sidetone paths,
noise suppression etc. depend on the selected mode and can be altered with AT commands
(except for mode 1).
Both analog audio interfaces can be used to connect headsets with microphones or
speakerphones. Headsets can be operated in audio mode 3, speakerphones in audio
mode 2. Audio mode 5 can be used for a speech coder without signal pre or post processing.
When shipped from factory, all audio parameters of TC65 are set to interface 1 and audio
mode 1. This is the default configuration optimized for the Votronic HH-SI-30.3/V1.1/0
handset and used for type approving the Siemens reference configuration. Audio mode 1 has
fix parameters which cannot be modified. To adjust the settings of the Votronic handset
simply change to another audio mode.
TC65_HD_V00.450
Page 53 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
3.13.1
Speech Processing
The speech samples from the ADC or DAI are handled by the DSP of the baseband
controller to calculate e.g. amplifications, sidetone, echo cancellation or noise suppression
depending on the configuration of the active audio mode. These processed samples are
passed to the speech encoder. Received samples from the speech decoder are passed to
the DAC or DAI after post processing (frequency response correction, adding sidetone etc.).
Full rate, half rate, enhanced full rate, adaptive multi rate (AMR), speech and channel
encoding including voice activity detection (VAD) and discontinuous transmission (DTX) and
digital GMSK modulation are also performed on the GSM baseband processor.
3.13.2
Microphone Circuit
TC65 has two identical analog microphone inputs. There is no on-board microphone supply
circuit, except for the internal voltage supply VMIC and the dedicated audio ground line
AGND. Both lines are well suited to feed a balanced audio application or a single-ended
audio application.
The AGND line on the TC65 board is especially provided to achieve best grounding
conditions for your audio application. As there is less current flowing than through other GND
lines of the module or the application, this solution will avoid hum and buzz problems.
3.13.2.1
Single-ended Microphone Input
Figure 18 as well as Figure 38 show an example of how to integrate a single-ended
microphone input.
RA = typ. 2k
RB = typ. 5k
RVMIC = typ. 470Ohm
VMIC
RA
RA
RVMIC
Ck = typ. 100nF
CF = typ. 22µF
MICPx
VMIC = typ. 2.5V
VBias
CF
GSM module
MICNx
RB
Vbias = 1.0V … 1.6V, typ. 1.5V
CK
AGND
Figure 18: Single ended microphone input
RA has to be chosen so that the DC voltage across the microphone falls into the bias voltage
range of 1.0V to 1.6V and the microphone feeding current meets its specification.
The MICNx input is automatically self biased to the MICPx DC level. It is AC coupled via CK
to a resistive divider which is used to optimize supply noise cancellation by the differential
microphone amplifier in the module.
TC65_HD_V00.450
Page 54 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
The VMIC voltage should be filtered if gains larger than 20dB are used. The filter can be
attached as a simple first order RC-network (RVMIC and CF).
This circuit is well suited if the distance between microphone and module is kept short. Due
to good grounding the microphone can be easily ESD protected as its housing usually
connects to the negative terminal.
3.13.2.2
Differential Microphone Input
Figure 19 shows a differential solution for connecting an electret microphone.
RA = typ. 1k
RVMIC = 470Ohm
VMIC
RVMIC
CK = typ. 100nF
CF = typ. 22µF
RA
MICPx
CF
VMIC = typ. 2.5V
GSM module
Vbias = 1.0V … 1.6V, typ. 1.5V
MICNx
VBias
RA
CK
AGND
Figure 19: Differential microphone input
The resulting DC voltage between MICPx and AGND should be in the range of 1.0V to 1.6V
to bias the input amplifier. MICNx is automatically self biased to the MICPx DC level. The
resulting AC differential voltage is then amplified in the GSM module.
The VMIC voltage should be filtered if gains larger than 20dB are used. The filter can be
attached as a simple first order RC-network (RVMIC and CF).
The advantage of this circuit is that it can be used if the application involves longer lines
between microphone and module.
TC65_HD_V00.450
Page 55 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
3.13.2.3
Line Input Configuration with OpAmp
Figure 20 shows an example of how to connect an opamp into the microphone circuit.
RA = typ. 47k
RVMIC = 470Ohm
VMIC
RA
CK
RVMIC
Ck = typ. 100nF
CF = typ. 22µF
MICPx
VMIC = typ. 2.5V
RA
CK
GSM module
MICNx
CF
Vbias = typ. ½ VMIC = 1.25V
VBias
AGND
Figure 20: Line input configuration with OpAmp
The AC source (e.g. an opamp) and its reference potential have to be AC coupled to the
MICPx resp. MICNx input terminals. The voltage divider between VMIC and AGND is
necessary to bias the input amplifier. MICNx is automatically self biased to the MICPx DC
level.
The VMIC voltage should be filtered if gains larger than 20dB are used. The filter can be
attached as a simple first order RC-network (RVMIC and CF). If a high input level and a lower
gain are applied the filter is not necessary.
If desired, MICNx via CK can also be connected to the inverse output of the AC source
instead of connecting it to the reference potential for differential line input.
TC65_HD_V00.450
Page 56 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
3.13.3
Loudspeaker Circuit
The GSM module comprises two analog speaker outputs: EP1 and EP2. Output EP1 is able
to drive a load of 8Ohms while the output EP2 can drive a load of 32Ohms. Each interface
can be connected in differential and in single ended configuration. See examples in Figure
21 and Figure 22.
Loudspeaker impedance
EPP1/EPN1
ZL = typ. 8Ohm
EPP2/EPN2
ZL = typ. 32Ohm
EPPx
GSM module
EPNx
AGND
Figure 21: Differential loudspeaker configuration
Loudspeaker impedance
EPP1/EPN1
ZL = typ. 8Ohm
Ck = 220µF
EPPx
EPP2/EPN2
ZL = typ. 32Ohm
Ck = 47µF
GSM module
EPNx
Ck
AGND
Figure 22: Single ended loudspeaker configuration
TC65_HD_V00.450
Page 57 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
3.13.4
Digital Audio Interface DAI
TBD
TC65_HD_V00.450
Page 58 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
3.14
Control Signals
3.14.1
Synchronization Signal
The synchronization signal serves to indicate growing power consumption during the transmit
burst. The signal is generated by the SYNC pin (pin number 32). Please note that this pin
can adopt three different operating modes which you can select by using the AT^SSYNC
command: the mode AT^SSYNC=0 described below, and the two LED modes AT^SSYNC=1
or AT^SSYNC=2 described in [1] and Section 3.14.2.
The first function (factory default AT^SSYNC=0) is recommended if you want your
application to use the synchronization signal for better power supply control. Your platform
design must be such that the incoming signal accommodates sufficient power supply to the
TC65 module if required. This can be achieved by lowering the current drawn from other
components installed in your application.
The timing of the synchronization signal is shown below. High level of the SYNC pin
indicates increased power consumption during transmission.
1 Tx 577 µs every 4.616 ms
2 Tx 1154 µs every 4.616 ms
Transmit burst
SYNC signal*)
t = 180µs
Figure 25: SYNC signal during transmit burst
*)
The duration of the SYNC signal is always equal, no matter whether the traffic or the
access burst are active.
TC65_HD_V00.450
Page 59 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
3.14.2
Using the SYNC Pin to Control a Status LED
As an alternative to generating the synchronization signal, the SYNC pin can be configured
to drive a status LED that indicates different operating modes of the TC65 module. To take
advantage of this function the LED mode must be activated with the AT^SSYNC command
and the LED must be connected to the host application. The connected LED can be operated
in two different display modes (AT^SSYNC=1 or AT^SSYNC=2). For details please refer to
[1].
Especially in the development and test phase of an application, system integrators are
advised to use the LED mode of the SYNC pin in order to evaluate their product design and
identify the source of errors.
To operate the LED a buffer, e.g. a transistor or gate,
must be included in your application. A sample circuit
is shown in Figure 26. Power consumption in the LED
mode is the same as for the synchronization signal
mode. For details see Table 17, SYNC pin.
Figure 26: LED Circuit (Example)
TC65_HD_V00.450
Page 60 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
Antenna Interface
The RF interface has an impedance of 50Ω. TC65 is capable of sustaining a total mismatch
at the antenna connector or pad without any damage, even when transmitting at maximum
RF power.
The external antenna must be matched properly to achieve best performance regarding
radiated power, DC-power consumption, modulation accuracy and harmonic suppression.
Antenna matching networks are not included on the TC65 PCB and should be placed in the
host application.
Regarding the return loss TC65 provides the following values in the active band:
Table 11: Return loss in the active band
State of module
Return loss of module
Recommended return loss of application
Receive
> 8dB
> 12dB
Transmit
not applicable
> 12dB
The connection of the antenna or other equipment must be decoupled from DC voltage. This
is necessary because the antenna connector is DC coupled to ground via an inductor for
ESD protection.
4.1
Antenna Installation
To suit the physical design of individual applications TC65 offers two alternative approaches
to connecting the antenna:
• Recommended approach: U.FL-R-SMT antenna connector from Hirose assembled on
the component side of the PCB (top view on TC65). See Section 4.3 for details.
• Antenna pad and grounding plane placed on the bottom side. See Section 4.2.
The U.FL-R-SMT connector has been chosen as antenna reference point (ARP) for the
Siemens reference equipment submitted to type approve TC65. All RF data specified
throughout this manual are related to the ARP. For compliance with the test results of the
Siemens type approval you are advised to give priority to the connector, rather than using the
antenna pad.
IMPORTANT: Both solutions can only be applied alternatively. This means, whenever an
antenna is plugged to the Hirose connector, the pad must not be used. Vice versa, if the
antenna is connected to the pad, then the Hirose connector must be left empty.
TC65_HD_V00.450
Page 61 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
Antenna connected to Hirose connector:
Module
PAD
U.FL
Antenna connected to pad:
Antenna or
measurement
equipment
Module
PAD
50Ohm
50Ohm
50Ohm
U.FL
Antenna
50Ohm
Figure 27: Never use antenna connector and antenna pad at the same time
No matter which option you choose, ensure that the antenna pad does not come into contact
with the holding device or any other components of the host application. It needs to be
surrounded by a restricted area filled with air, which must also be reserved 0.8mm in height.
U.FL antenna connector
RF section
PCB
Antenna pad
Restricted area
Figure 28: Restricted area around antenna pad
TC65_HD_V00.450
Page 62 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
4.2
Antenna Pad
The antenna can be soldered to the pad, or attached via contact springs. For proper
grounding connect the antenna to the ground plane on the bottom of TC65 which must be
connected to the ground plane of the application.
When you decide to use the antenna pad take into account that the pad has not been
intended as antenna reference point (ARP) for the Siemens TC65 type approval. The
antenna pad is provided only as an alternative option which can be used, for example, if the
recommended Hirose connection does not fit into your antenna design.
Also, consider that according to the GSM recommendations TS 45.005 and TS 51.010-01 a
50Ω connector is mandatory for type approval measurements. This requires GSM devices
with an integral antenna to be temporarily equipped with a suitable connector or a low loss
RF cable with adapter.
Notes on soldering:
• To prevent damage to the module and to obtain long-term solder joint properties you are
advised to maintain the standards of good engineering practice for soldering.
• Be sure to solder the antenna core to the pad and the shielding of the coax cable to the
ground plane of the module next to the antenna pad. The direction of the cable is not
relevant from the electrical point of view.
TC65 material properties:
TC65 PCB:
FR4
Antenna pad:
Gold plated pad
4.2.1
Suitable Cable Types
For direct solder attachment, we suggest to use the following cable types:
• RG316/U 50Ohm coaxial cable
• 1671A 50Ohm coaxial cable
Suitable cables are offered, for example, by IMS Connector Systems. For further details and
other cable types please contact http://www.imscs.com.
TC65_HD_V00.450
Page 63 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
4.3
Antenna Connector
TC65 uses an ultra-miniature SMT antenna connector supplied
from Hirose Ltd. The product name is:
U.FL-R-SMT
The position of the antenna connector on the TC65 board can be
seen in Figure 35.
Figure 29: Mechanical dimensions of U.FL-R-SMT connector
Table 12: Product specifications of U.FL-R-SMT connector
Item
Specification
Conditions
Nominal impedance
50Ω
Rated frequency
DC to 3GHz
Operating temp:-40°C to + 90°C
Operating humidity: max. 90%
Ratings
Mechanical characteristics
Female contact holding
force
0.15N min
Measured with a ∅ 0.475 pin
gauge
Repetitive operation
Contact resistance:
Center 25mΩ
Outside 15mΩ
30 cycles of insertion and
disengagement
Vibration
No momentary disconnections of
1µs;
No damage, cracks and looseness
of parts
Frequency of 10 to 100Hz, single
amplitude of 1.5mm, acceleration
of 59m/s2, for 5 cycles in the
direction of each of the 3 axes
Shock
No momentary disconnections of
Acceleration of 735m/s2, 11ms
1µs.
duration for 6 cycles in the
No damage, cracks and looseness direction of each of the 3 axes
of parts.
Environmental characteristics
Humidity resistance
No damage, cracks and looseness Exposure to 40°C, humidity of
95% for a total of 96 hours
of parts.
Insulation resistance:
100MΩ min. at high humidity
500MΩ min. when dry
Temperature cycle
No damage, cracks and looseness
of parts.
Contact resistance:
Center 25mΩ
Outside 15mΩ
Temperature: +40°C → 5 to 35°C
→ +90°C → 5 to 35°C
Time: 30min → within 5min →
30min within 5min
Salt spray test
No excessive corrosion
48 hours continuous exposure to
5% salt water
TC65_HD_V00.450
Page 64 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
Table 13: Material and finish of U.FL-R-SMT connector and recommended plugs
Part
Material
Finish
Shell
Phosphor bronze
Silver plating
Male center contact
Brass
Gold plating
Female center contact
Phosphor bronze
Gold plating
Insulator
Plug:
Receptacle:
PBT
LCP
Black
Beige
Mating plugs and cables can be chosen from the Hirose U.FL Series. Examples are shown
below and listed in Table 14. For latest product information please contact your Hirose dealer
or visit the Hirose home page, for example http://www.hirose.com.
Figure 30: U.FL-R-SMT connector with U.FL-LP-040 plug
Figure 31: U.FL-R-SMT connector with U.FL-LP-066 plug
TC65_HD_V00.450
Page 65 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
In addition to the connectors illustrated above, the U.FL-LP-(V)-040(01) version is offered as
an extremely space saving solution. This plug is intended for use with extra fine cable (up to
∅ 0.81mm) and minimizes the mating height to 2mm. See Figure 32 which shows the Hirose
datasheet.
Figure 32: Specifications of U.FL-LP-(V)-040(01) plug
TC65_HD_V00.450
Page 66 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
Table 14: Ordering information for Hirose U.FL Series
Item
Part number
HRS number
Connector on TC65
U.FL-R-SMT
CL331-0471-0-10
Right-angle plug shell for
∅ 0.81mm cable
U.FL-LP-040
CL331-0451-2
Right-angle plug for
∅ 0.81mm cable
U.FL-LP(V)-040 (01)
CL331-053-8-01
Right-angle plug for
∅ 1.13mm cable
U.FL-LP-068
CL331-0452-5
Right-angle plug for
∅ 1.32mm cable
U.FL-LP-066
CL331-0452-5
Extraction jig
E.FL-LP-N
CL331-04441-9
TC65_HD_V00.450
Page 67 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
Electrical, Reliability and Radio Characteristics
5.1
Absolute Maximum Ratings
The absolute maximum ratings stated in Table 15 are stress ratings under non-operating
conditions. Stresses beyond any of these limits will cause permanent damage to TC65.
Table 15: Absolute maximum ratings under non-operating conditions
Parameter
Min
Max
Unit
Supply voltage BATT+
-0.3
5.5
Voltage at digital pins
-0.3
3.05
Voltage at analog pins
-0.3
3.0
Voltage at VCHARGE pin
-0.3
5.5
Voltage at CHARGEGATE pin
-0.3
5.5
VUSB_IN
-0.3
5.5
VSENSE
5.5
ISENSE
5.5
5.2
Operating Temperatures
Test conditions were specified in accordance with IEC 60068-2 (still air). The values stated
below are in compliance with GSM recommendation TS 51.010-01.
Table 16: Operating temperatures
Parameter
Min
Ambient temperature (according to GSM 11.10)
Typ
Ambient temperature for charging (software controlled fast
charging)
Unit
*)
°C
-30
+25
+65
-30
-20
-----
+90*)
+60
°C
---
+45
°C
Automatic shutdown
TC65 board temperature
Battery temperature
Max
Due to temperature measurement uncertainty, a tolerance on these switching off thresholds
may occur. The possible deviation is in a range of:
• ± 3°C at the overtemperature limit
• ± 5°C at the undertemperature limit
*)
On TC65 the automatic overtemperature shutdown threshold is set to 90°C board
temperature. This prevents permanent damage to components on the board. Consider
the ratio of output power, supply voltage and operating temperature: to achieve Tamb max
= 65°C in GPRS Class 8 (GSM900/ GSM850) with 2W RF power the supply voltage
must not be higher than 4.2V.
TC65_HD_V00.450
Page 68 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
5.3
Pin Assignment and Signal Description
The Molex board-to-board connector on TC65 is an 80-pin double-row receptacle. The
names and the positions of the pins can be seen from Figure 1 which shows the top view of
TC65.
GND
GND
80
ADC1_IN
DAC_OUT
79
ADC2_IN
PWR_IND
78
GND
Do not use
77
GPIO10
GPIO9
76
GPIO8
SPICS
75
SPIDI
GPIO4
74
GPIO7
GPIO3
73
GPIO6
GPIO2
72
10
GPIO5
GPIO1
71
11
I2CCLK_SPICLK
I2CDAT_SPIDO
70
12
VUSB_IN
USB_DP
69
13
DAI5
USB_DN
68
14
ISENSE
VSENSE
67
15
DAI6
VMIC
66
16
CCCLK
EPN2
65
17
CCVCC
EPP2
64
18
CCIO
EPP1
63
19
CCRST
EPN1
62
20
CCIN
MICN2
61
21
CCGND
MICP2
60
22
DAI4
MICP1
59
23
DAI3
MICN1
58
24
DAI2
AGND
57
25
DAI1
IGT
56
26
DAI0
EMERG_RST
55
27
BATT_TEMP
DCD0
54
28
SYNC
CTS1
53
29
RXD1
CTS0
52
30
RXD0
RTS1
51
31
TXD1
DTR0
50
32
TXD0
RTS0
49
33
VDDLP
DSR0
48
34
VCHARGE
RING0
47
35
CHARGEGATE
VEXT
46
36
GND
BATT+
45
37
GND
BATT+
44
38
GND
BATT+
43
39
GND
BATT+
42
40
GND
BATT+
41
Figure 33: Pin assignment (component side of TC65)
TC65_HD_V00.450
Page 69 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
Please note that the reference voltages listed in Table 17 are the values measured directly
on the TC65 module. They do not apply to the accessories connected.
Table 17: Signal description
Function
Signal name
Power
supply
BATT+
IO
Signal form and level
Comment
VImax = 4.5V
VItyp = 3.8V
VImin = 3.2V during Tx burst on board
Five pins of BATT+ and GND
must be connected in parallel
for supply purposes because
higher peak currents may
occur.
Minimum voltage must not fall
below 3.2V including drop,
ripple, spikes.
I ≈ 2A, during Tx burst
n Tx = n x 577µs peak current every
4.616ms
Power
supply
GND
Ground
Application Ground
Charge
Interface
VCHARGE
VImin = 1.015 * VBATT+
VImax = 5.45V
This line signalizes to the
processor that the charger is
connected.
If unused keep pin open.
BATT_TEMP
Battery temperature
Connect NTC with RNTC ≈ 10kΩ @ 25°C to
measurement via NTC
ground. See Section 3.5.3 for B value of
resistance.
NTC.
NTC should be installed
inside or near battery pack to
enable proper charging and
deliver temperature values.
If unused keep pin open.
ISENSE
VImax = 4.65V
∆VImax to VBATT+ = +0.3V at normal
condition
External
supply
voltage
ISENSE is required for
measuring the charge current.
For this purpose, a shunt
resistor for current
measurement needs to be
connected between ISENSE
and VSENSE.
If unused connect pin to
VSENSE.
VSENSE
VImax = 4.5V
VSENSE must be directly
connected to BATT+ at
battery connector or external
power supply.
CHARGEGATE
VOmax = 5.5V
IOmax = 1mA
Control line to the gate of
charge FET
If unused keep pin open.
VEXT
Normal mode:
VEXT may be used for
application circuits, for
example to supply power for
an I2C
TC65_HD_V00.450
VOmin = 2.75V
VOtyp = 2.93V
VOmax = 3.05V
IOmax = -50mA
Page 70 of 96
If unused keep pin open.
Not available in Power-down
mode. The external digital
logic must not cause any
spikes or glitches on voltage
VEXT.
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
Function
Signal name
IO
Signal form and level
Comment
Power
indicator
PWR_IND
VIHmax = 10V
VOLmax = 0.4V at Imax = 2mA
PWR_IND (Power Indicator)
notifies the module’s on/off
state.
PWR_IND is an open
collector that needs to be
connected to an external pullup resistor. Low state of the
open collector indicates that
the module is on. Vice versa,
high level notifies the Powerdown mode.
Therefore, the pin may be
used to enable external
voltage regulators which
supply an external logic for
communication with the
module, e.g. level converters.
Ignition
IGT
RI ≈ 30kΩ, CI ≈ 10nF
VILmax = 0.8V at Imax = -150µA
VOHmax = 4.5V (VBATT+)
This signal switches the
mobile on.
This line must be driven low
by an open drain or open
collector driver.
ON
Emergency
reset
EMERG_RST
~~~
|____|~~~ Active Low ≥ 400ms
RI ≈ 5kΩ
VILmax = 0.2V at Imax = -0.5mA
VOHmin = 1.75V
VOHmax = 3.05V
~~~
|______|~~~ Pull down ≥ 10ms
Signal
Falling edge resets module.
Synchronization
SYNC
VOLmax = 0.3V at I = 0.1mA
VOHmin = 2.3V at I = -0.1mA
VOHmax = 0.05V
n Tx = n x 577µs impulse each 4.616ms,
with ___µs forward time.
RTC backup
VDDLP
TC65_HD_V00.450
I/O RI ≈ 1kΩ
VOmax = 4.5V
VBATT+ = 4.3V:
VO = 3.2V at IO = -500µA
VBATT+ = 0V:
VI = 2.7V…4.5V at Imax = 15µA
Page 71 of 96
Reset function in case of
emergency: Pull down and
release EMERG_RST. Falling
edge will reset the module.
Data stored in the volatile
memory will be lost. For
orderly software controlled
reset rather use the
AT+CFUN command (e.g.
AT+CFUN=,1).
This line must be driven by
open drain or open collector.
If unused keep pin open.
There are two alternative
options for using the SYNC
pin:
a) Indicating increased
current consumption during
uplink transmission burst.
Note that the timing of the
signal is different during
handover.
b) Driving a status LED to
indicate different operating
modes of TC65. The LED
must be installed in the host
application.
If unused keep pin open.
If unused keep pin open.
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
Function
Signal name
SIM interface CCIN
specified for
use with 3V
SIM card
IO
Signal form and level
Comment
RI ≈ 100kΩ
VILmax = 0.6V at I = -25µA
VIHmin = 2.1V at I = -10µA
VOmax = 3.05V
CCIN = Low, SIM card holder
closed
RO ≈ 47Ω
VOLmax = 0.25V at I = +1mA
VOHmin = 2.5V at I = -0.5mA
VOHmax = 2.95V
Maximum cable length or
copper track 100mm to SIM
card holder.
CCRST
CCIO
I/O RI ≈ 4.7kΩ
VILmax = 0.75V
VILmin = -0.3V
VIHmin = 2.1V
VIHmax = CCVCCmin + 0.3V = 3.05V
RO ≈ 100Ω
VOLmax = 0.3V at I = +1mA
VOHmin = 2.5V at I = -0.5mA
VOHmax = 2.95V
CCCLK
RO ≈ 100Ω
VOLmax = 0.3V at I = +1mA
VOHmin = 2.5V at I = -0.5mA
VOHmax = 2.95V
CCVCC
VOmin = 2.75V
VOtyp = 2.85V
VOmax = 2.95V
IOmax = -20mA
CCGND
SIM interface CCIN
specified for
use with
1.8V SIM
card
CCRST
CCIO
RI ≈ 100kΩ
VILmax = 0.6V at I = -25µA
VIHmin = 2.1V at I = -10µA
VOmax = 3.05V
RO ≈ 47Ω
VOLmax = 0.25V at I = +1mA
VOHmin = 1.45V at I = -0.5mA
VOHmax = 1.90V
I/O RI ≈ 4.7kΩ
VILmax = 0.45V
VIHmin = 1.35V
VIHmax = CCVCCmin + 0.3V = 2.00V
CCCLK
RO ≈ 100Ω
VOLmax = 0.3V at I = +1mA
VOHmin = 1.45V at I = -0.5mA
VOHmax = 1.90V
CCVCC
VOmin = 1.70V,
VOtyp = 1.80V
VOmax = 1.90V
IOmax = -20mA
CCGND
RXD0
TXD0
CTS0
RTS0
DTR0
DCD0
DSR0
RING0
TC65_HD_V00.450
All signals of SIM interface
are protected against ESD
with a special diode array.
Usage of CCGND is
mandatory.
Ground
RO ≈ 100Ω
VOLmax = 0.3V at I = +1mA
VOHmin = 1.45V at I = -0.5mA
VOHmax = 1.90V
ASC0
Serial
interface
CCIN = Low, SIM card holder
closed
Maximum cable length or
copper track 100mm to SIM
card holder.
All signals of SIM interface
are protected against ESD
with a special diode array.
Usage of CCGND is
mandatory.
Ground
VOLmax = 0.2V at I = 2mA
VOHmin = 2.55V at I = -0.5mA
VOHmax = 3.05V
VILmax = 0.8V
VIHmin = 2.0V
VIHmax = VEXTmin + 0.3V = 3.05V
Page 72 of 96
Serial interface for AT
commands or data stream.
If lines are unused keep pins
open.
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
Function
Signal name
IO
Signal form and level
Comment
ASC1
Serial
interface
RXD1
TXD1
CTS1
RTS1
VOLmax = 0.2V at I = 2mA
VOHmin = 2.55V at I = -0.5mA
VOHmax = 3.05V
Serial interface for AT
commands or data stream.
I2CCLK _SPICLK
VOLmax = 0.2V at I = 2mA
VOHmin = 2.55V at I = -0.5mA
VOHmax = 3.05V
I2CDAT_SPIDO
I/O VOLmax = 0.2V at I = 2mA
VILmax = 0.8V
VIHmin = 2.0V
I2C interface
VILmax = 0.8V
VIHmin = 2.0V
VIHmax = VEXTmin + 0.3V = 3.05V
VIHmax = VEXTmin + 0.3V = 3.05V
SPI
Serial
Peripheral
Interface
USB
If lines are unused keep pins
open.
I2C interface is only available
if the two pins are not used as
SPI interface.
I2CDAT is configured as
Open Drain and needs a pullup resistor in the host
application.
According to the I2C Bus
Specification Version 2.1 for
the fast mode a rise time of
max. 300ns is permitted.
There is also a maximum
VOL=0.4V at 3mA specified.
The value of the pull-up
depends on the capacitive
load of the whole system (I2C
Slave + lines). The maximum
sink current of I2CDAT and
I2CCLK is 4mA.
If lines are unused keep pins
open.
SPIDI
I2CDAT_SPIDO
I2CCLK_SPICLK
SPICS
VOLmax = 0.2V at I = 2mA
VOHmin = 2.55V at I = -0.5mA
VOHmax = 3.05V
If the Serial Peripheral
Interface is active the I2C
interface is not available.
VILmax = 0.8V
VIHmin = 2.0V,
VIHmax = VEXTmin + 0.3V = 3.05V
If lines are unused keep pins
open.
VUSB_IN
VINmin = 4.0V
VINmax = 5.25V
If lines are unused keep pins
open.
USB_DN
USB_DP
I/O Differential Output Crossover voltage
I/O Range
VCRSmin = 1.5V, VCRSmax = 2.0V
Driver Output Resistance
ZDRVtyp = 32Ohm
General
Purpose
Input/Output
GPIO1
GPIO2
GPIO3
GPIO4
I/O VOLmax = 0.2V at I = 2mA
I/O VOHmin = 2.55V at I = -0.5mA
VOHmax = 3.05V
I/O
GPIO6
I/O VILmax = 0.8V
I/O VIHmin = 2.0V,
I/O VIHmax = VEXTmin + 0.3V = 3.05V
GPIO7
I/O
GPIO8
I/O
GPIO9
I/O
GPIO10
I/O
GPIO5
TC65_HD_V00.450
Page 73 of 96
If unused keep pins with a pull
up or pull down resistor while
the GPIO is set to input.
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
Function
Signal name
Analog
Digital
Converter
ADC_IN1
ADC_IN2
Digital
Analog
Converter
DAC_OUT
Digital Audio
interface
DAI0
Analog
Audio
interface
IO
Signal form and level
Comment
Input voltage: VImin = 0V, VImax = 2.4V
Ri ≈ 450kOhm
fCmax < 3kHz
Sensitivity, accuracy: 12 Bit
1 Bit = 0.585mV
VOLmax = 0.2V at I = 2mA
VOHmin = 2.55V at I = -0.5mA
VOHmax = 3.05V
Inputs used for measuring
external voltages.
ADC_IN1 and ADC_IN2 are
internally multiplexed through
analog switch.
VOLmax = 0.2V at I = 2mA
VOHmin = 2.55V at I = -0.5mA
VOHmax = 3.05V
See Table 10 for details.
If unused keep pins open.
PWM signal which can be
smoothed by an external filter.
DAI1
DAI2
DAI3
DAI4
DAI5
DAI6
VMIC
VOmin = 2.4V
VOtyp = 2.5V
VOmax = 2.6V
Imax = 2mA
Microphone supply for
customer feeding circuits
EPP2
EPN2
1.0954Vpp (differential) typical
3.4Vpp differential maximal
Audio mode TBD
Measurement conditions TBD
Minimum differential resp. single ended
load 27Ohms
The audio output can directly
operate a 32-Ohmloudspeaker.
If unused keep pins open.
1.0954Vpp (differential) typical
6.0Vp-p differential maximal
Audio mode TBD
Measurement conditions TBD
Minimum differential resp. single ended
load 7.5Ohms
The audio output can directly
operate an 8-Ohmloudspeaker.
If unused keep pins open.
Full Scale Input Voltage 1.578Vpp
0dBm0 Input Voltage
1.0954Vpp
At MICNx, apply external bias from 1.0V to
1.6V.
Audio mode TBD
Measurement conditions TBD
Balanced or single ended
microphone or line inputs with
external feeding circuit (using
VMIC and AGND).
If unused keep pins open.
Analog Ground
GND level for external audio
circuits
EPP1
EPN1
MICP1
MICN1
MICP2
MICN2
AGND
TC65_HD_V00.450
VILmax = 0.8V
VIHmin = 2.0V
VIHmax = VEXTmin + 0.3V = 3.05V
Page 74 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
5.4
Power Supply Ratings
Table 18: Power supply ratings
Parameter Description
Conditions
Min
BATT+
Directly measured at reference point
TP BATT+ and TP GND, see chapter
3.2.2
3.2
Supply voltage
Typ
3.8
Max
Unit
4.5
400
mV
@ f<200kHz
50
mV
@ f>200kHz
mV
Voltage must stay within the min/max
values, including voltage drop, ripple,
spikes.
IVDDLP
IBATT+
Voltage drop during
transmit burst
Normal condition, power control level
for Pout max
Voltage ripple
Normal condition, power control level
for Pout max
OFF State
supply current
Average standby
supply current2)
RTC Backup
@ BATT+ = 0V
1)
25
POWER DOWN mode
50
SLEEP mode
@ DRX = 9
TBD
mA
SLEEP mode
@ DRX = 5
TBD
mA
SLEEP mode
@ DRX = 2
TBD
mA
IDLE mode
@ DRX = 2
TBD
mA
1)
Measured after module INIT (switch ON the module and following switch OFF);
applied voltage on BATT+ (w/o INIT) show increased POWER DOWN supply current.
2)
Additional conditions:
SLEEP measurements started 3 minutes after switch ON the module
Averaging times: SLEEP mode - 3 minutes; IDLE mode - 1.5 minutes
Communication tester settings: no neighbor cells, no cell reselection
USB interface disabled
TC65_HD_V00.450
µA
Page 75 of 96
100
µA
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
Table 19: Current consumption during transmit burst
Mode
Timeslot configuration
GSM call
GPRS Class 8
GPRS Class10
GPRS Class 12
1Tx / 1Rx
1Tx / 4Rx
2Tx / 3Rx
4Tx / 1Rx
*)
Frequency
850/900MHz
Maximum possible power
(RF power nominal)
2W
(33dBm)
2W
(33dBm)
2W
(33dBm)
1W
(30dBm)
1W
(30dBm)
0.5W
(27dBm)
Radio/output power reduction
with command AT^SCFG,
parameter 
 = 1 .. 3
 = 1 .. 3
 = 1
 = 2 or 3
 = 1
 = 2 or 3
Burst current @ 50Ω antenna
(typ.)
2.0A
2.0A
2.0A
1.5A
1.5A
1.3A
Burst current @ total mismatch
3.2A
3.2A
3.2A
2.3A
2.3A
1.9A
Average current @ 50Ω antenna 335mA
(typ.)
385mA
610mA
485mA
810mA
710mA
Average current @ total
mismatch
535mA
910mA
685mA
1210mA
1010mA
Current characteristics
485mA
*)
Currents in the frequency bands GSM 1800MHz and GSM 1900MHz are lower due to lower RF output levels.
AT parameters are given in brackets <...> and marked italic.
TC65_HD_V00.450
Page 76 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
5.5
Electrostatic Discharge
The GSM engine is not protected against Electrostatic Discharge (ESD) in general.
Consequently, it is subject to ESD handling precautions that typically apply to ESD sensitive
components. Proper ESD handling and packaging procedures must be applied throughout
the processing, handling and operation of any application that incorporates a TC65 module.
Special ESD protection provided on TC65:
Antenna interface: one spark discharge line (spark gap)
SIM interface: clamp diodes for protection against overvoltage.
The remaining ports of TC65 are not accessible to the user of the final product (since they
are installed within the device) and therefore, are only protected according to the “Human
Body Model” requirements.
TC65 has been tested according to the EN 61000-4-2 standard. The measured values can
be gathered from the following table.
Table 20: Measured electrostatic values
Specification / Requirements
Contact discharge
Air discharge
ESD at SIM port
± 4kV
± 8kV
ESD at antenna port
± 4kV
± 8kV
ETSI EN 301 489-7
Human Body Model (Test conditions: 1.5kΩ, 100pF)
ESD at USB interface
± 1kV
± 1kV
ESD at all other interfaces
± 1kV
± 1kV
Note: Please note that the values may vary with the individual application design. For
example, it matters whether or not the application platform is grounded over external
devices like a computer or other equipment, such as the Siemens reference
application described in Chapter 8.
TC65_HD_V00.450
Page 77 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
5.6
Reliability Characteristics
The test conditions stated below are an extract of the complete test specifications.
Table 21: Summary of reliability test conditions
Type of test
Conditions
Standard
Vibration
Frequency range: 10-20Hz; acceleration: 3.1mm
amplitude
Frequency range: 20-500Hz; acceleration: 5g
Duration: 2h per axis = 10 cycles; 3 axes
DIN IEC 68-2-6
Shock half-sinus
Acceleration: 500g
Shock duration: 1msec
1 shock per axis
6 positions (± x, y and z)
DIN IEC 68-2-27
Dry heat
Temperature: +70 ±2°C
Test duration: 16h
Humidity in the test chamber: < 50%
EN 60068-2-2 Bb ETS
300019-2-7
Temperature
change (shock)
Low temperature: -40°C ±2°C
High temperature: +85°C ±2°C
Changeover time: < 30s (dual chamber system)
Test duration: 1h
Number of repetitions: 100
DIN IEC 68-2-14 Na
High temperature: +55°C ±2°C
Low temperature: +25°C ±2°C
Humidity: 93% ±3%
Number of repetitions: 6
Test duration: 12h + 12h
DIN IEC 68-2-30 Db
Temperature: -40 ±2°C
Test duration: 16h
DIN IEC 68-2-1
Damp heat cyclic
Cold (constant
exposure)
TC65_HD_V00.450
Page 78 of 96
ETS 300019-2-7
ETS 300019-2-5
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
Mechanics
6.1
Mechanical Dimensions of TC65
Figure 34 shows the top view of TC65 and provides an overview of the board's mechanical
dimensions. For further details see Figure 35.
Pin 1
Pin 80
Figure 34: TC65 – top view
TC65_HD_V00.450
Page 79 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
All dimensions in mm
Figure 35: Dimensions of TC65
TC65_HD_V00.450
Page 80 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
6.2
Mounting TC65 to the Application Platform
There are many ways to properly install TC65 in the host device. An efficient approach is to
mount the TC65 PCB to a frame, plate, rack or chassis.
Fasteners can be M2 screws plus suitable washers, circuit board spacers, or customized
screws, clamps, or brackets. In addition, the board-to-board connection can also be utilized
to achieve better support. To help you find appropriate spacers a list of selected screws and
distance sleeves for 3mm stacking height can be found in Section 9.2.
When using the two small holes take care that the screws are inserted with the screw head
on the bottom of the TC65 PCB. Screws for the large holes can be inserted from top or
bottom.
For proper grounding it is strongly recommended to use large ground plane on the bottom of
board in addition to the five GND pins of the board-to-board connector. The ground plane
may also be used to attach cooling elements, e.g. a heat sink or thermally conductive tape.
To prevent mechanical damage, be careful not to force, bend or twist the module. Be sure it
is positioned flat against the host device.
All the information you need to install an antenna is summarized in Chapter 4. Note that the
antenna pad on the bottom of the TC65 PCB must not be influenced by any other PCBs,
components or by the housing of the host device. It needs to be surrounded by a restricted
space as described in Section 4.1.
TC65_HD_V00.450
Page 81 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
6.3
Board-to-Board Application Connector
This section provides the specifications of the 80-pin board-to-board connector used to
connect TC65 to the external application.
Connector mounted on the TC65 module:
Type:
52991-0808 SlimStack Receptacle
80 pins, 0.50mm pitch,
for stacking heights from 3.0 to 4.0mm,
see Figure 36 for details.
Supplier: Molex
www.molex.com
Table 22: Technical specifications of Molex board-to-board connector
Parameter
Specification (80-pin B2B connector)
Electrical
Number of Contacts
80
Contact spacing
0.5mm (.020")
Voltage
50V
Rated current
0.5A max per contact
Contact resistance
50mΩ max per contact
Insulation resistance
> 100MΩ
Dielectric Withstanding Voltage
500V AC (for 1 minute)
Physical
Insulator material (housing)
White glass-filled LCP plastic, flammability UL 94V 0
Contact material
Plating: Gold over nickel
Insertion force 1
st
Insertion force 30
< 74.4N
th
< 65.6N
Withdrawal force 1st
> 10.8N
Maximum connection cycles
30 (@ 70mΩ max per contact)
Mating connector types for the customer's application
offered by Molex:
• 53748-0808 SlimStack Plug, 3mm stacking height,
see Figure 37 for details.
•
53916-0808 SlimStack Plug, 4mm stacking height
TC65_HD_V00.450
Page 82 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
Figure 36: Molex board-to-board connector 52991-0808 on TC65
TC65_HD_V00.450
Page 83 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
Figure 37: Mating board-to-board connector 53748-0808 on application
TC65_HD_V00.450
Page 84 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
Sample Application
Figure 38 shows a typical example of how to integrate a TC65 module into the GSM part of a
mobile application. Usage of the various host interfaces depends on the desired features of
the application.
Audio interface 1 demonstrates the balanced connection of microphone and earpiece. This
solution is particularly well suited for internal transducers. Audio interface 2 uses an
unbalanced microphone and earpiece connection typically found in headset applications.
The charging circuit is optimized for the charging stages (trickle charging and software
controlled charging) as well as the battery and charger specifications described in Section
3.5.
The PWR_IND line is an open collector that needs an external pull-up resistor which
connects to the voltage supply of the microcontroller VCC µC. Low state of the open collector
pulls the PWR_IND signal low and indicates that the TC65 module is active, high level
notifies the Power-down mode.
If the module is in Power-down mode avoid current flowing from any other source into the
module circuit, for example reverse current from high state external control lines. Therefore,
the controlling application must be designed to prevent reverse or return flow. This is not
necessary for the USB interface.
The I2C interface can be powered from an external supply or via the VEXT line of TC65. The
advantage of this solution is that when the module enters the Power-down mode, the I2C
interface is shut down as well. If you prefer to connect an I2C interface to an external power
supply, take care that the interface is shut down when the PWR_IND signal goes high in
Power-down mode.
The EMC measures are best practice recommendations. In fact, an adequate EMC strategy
for an individual application is very much determined by the overall layout and, especially,
the position of components. For example, mounting the internal acoustic transducers directly
on the PCB eliminates the need to use the ferrite beads shown in the sample schematic.
However, when connecting cables to the module’s interfaces it is strongly recommended to
add appropriate ferrite beads for reducing RF radiation.
Disclaimer
No warranty, either stated or implied, is provided on the sample schematic diagram shown in
Figure 38 and the information detailed in this section. As functionality and compliance with
national regulations depend to a great amount on the used electronic components and the
individual application layout manufacturers are required to ensure adequate design and
operating safeguards for their products using TC65 modules.
TC65_HD_V00.450
Page 85 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
TC65 Application
(Draft) *)
VCHARGE BATT+
IGT
ESD
protection
Rechargeable
Lithium battery
0.3R
SI3441DV
BC847
CRS04
Vch ar ge 5.2V + 0.2V
Charger
47k
2.7k
NTC
EMERG_RST
VCC µC
BATTEMP
VSENSE
BC847
47k
100k
ISENSE
PWR_IND
Serial Interface
ASC0
CHARGEGATE
Digital Audio
VMIC (2.5V)
470R
Serial Interface
ASC1
TC65
*)
I2C
22µF
1k
MICP1
100nF
MICN1
2 x RP
1k
VEXT (2.9V)
2.2k
2.2k
MICP2
USB *)
(Slave)
100nF
MICN2
SYNC
CCIN
CCVCC
CCRST
CCIO
CCCLK
CCGND
SIM
200nF
1nF
27pF
GND
0R (not mounted)
EPN1
EPP1
>8R
5.6k
100µF
EPP2
EPN2
AGND
>32R
*)
All SIM components shall be close to card holder.
depends on final specification
Figure 38: TC65 sample application (draft)
TC65_HD_V00.450
Page 86 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
Reference Approval
8.1
Reference Equipment for Type Approval
The Siemens reference setup submitted to type approve TC65 consists of the following
components:
• Siemens TC65 cellular engine
• Development Support Box DSB75
• SIM card reader integrated on DSB75
• U.FL-R-SMT antenna connector and U.FL-LP antenna cable
• Handset type Votronic HH-SI-30.3/V1.1/0
• Li-Ion battery
• PC as MMI
Antenna or 50 Ω
cable to system
simulator
RS-232
Antenna
GSM module
DSB75
Flex cable
100mm
PC
SIM
Power supply
Li-Ion
battery
Handset
Figure 39: Reference equipment for Type Approval
TC65_HD_V00.450
Page 87 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
8.2
Compliance with FCC Rules and Regulations
The FCC Equipment Authorization Certification for the TC65 reference application described
in Section 8.1 is listed under the
FCC identifier QIPTC65
IC: 267W-TC65
granted to Siemens AG.
The TC65 reference application registered under the above identifier is certified to be in
accordance with the following Rules and Regulations of the Federal Communications
Commission (FCC).
Power listed is ERP for Part 22 and EIRP for Part 24
“This device contains GSM and GPRS Class12 functions in the 900 and 1800MHz
Band which are not operational in U.S. Territories.
This device is to be used only for mobile and fixed applications. The antenna(s) used
for this transmitter must be installed to provide a separation distance of at least 20cm
from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter. Users and installers must be provided with antenna installation
instructions and transmitter operating conditions for satisfying RF exposure compliance. Antennas used for this OEM module must not exceed 8.4dBi gain (GSM 1900)
and 2.9dBi (GSM 850) for mobile and fixed operating configurations. This device is
approved as a module to be installed in other devices.”
The FCC label of the module must be visible from the outside. If not, the host device is
required to bear a second label stating, “Contains FCC ID QIPTC65”.
IMPORTANT: Manufacturers of mobile or fixed devices incorporating TC65 modules are
advised to
• clarify any regulatory questions,
• have their completed product tested,
• have product approved for FCC compliance, and
• include instructions according to above mentioned RF exposure statements in end
product user manual.
Please note that changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
TC65_HD_V00.450
Page 88 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
Appendix
9.1
List of Parts and Accessories
Table 23: List of parts and accessories
Description
Supplier
Ordering information
TC65
Siemens
Siemens ordering number: L36880-N8355-A100
Siemens Car Kit Portable
Siemens
Siemens ordering number: L36880-N3015-A117
DSB75 Support Box
Siemens
Siemens ordering number: L36880-N8811-A100
Votronic Handset
VOTRONIC
Votronic HH-SI-30.3/V1.1/0
VOTRONIC
Entwicklungs- und Produktionsgesellschaft für
elektronische Geräte mbH
Saarbrücker Str. 8
66386 St. Ingbert
Germany
Phone: +49-(0)6 89 4 / 92 55-0
Fax:
+49-(0)6 89 4 / 92 55-88
e-mail:
contact@votronic.com
SIM card holder incl. push
button ejector and slide-in
tray
Molex
Ordering numbers:
91228
91236
Sales contacts are listed in Table 24.
Board-to-board connector
Molex
Sales contacts are listed in Table 24.
U.FL-R-SMT antenna
connector
Hirose
See Section 4.3 for details on U.FL-R-SMT
connector, mating plugs and cables.
Sales contacts are listed in Table 25.
TC65_HD_V00.450
Page 89 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
Table 24: Molex sales contacts (subject to change)
Molex
For further information
please click:
http://www.molex.com/
Molex Deutschland GmbH
Felix-Wankel-Str. 11
4078 Heilbronn-Biberach
Germany
Phone: +49-7066-9555 0
Fax:
+49-7066-9555 29
Email: mxgermany@molex.com
American Headquarters
Lisle, Illinois 60532
U.S.A.
Phone: +1-800-78MOLEX
Fax:
+1-630-969-1352
Molex China Distributors
Beijing,
Room 1319, Tower B,
COFCO Plaza
No. 8, Jian Guo Men Nei
Street, 100005
Beijing
P.R. China
Phone: +86-10-6526-9628
Phone: +86-10-6526-9728
Phone: +86-10-6526-9731
Fax:
+86-10-6526-9730
Molex Singapore Pte. Ltd.
Jurong, Singapore
Phone: +65-268-6868
Fax:
+65-265-6044
Molex Japan Co. Ltd.
Yamato, Kanagawa, Japan
Phone: +81-462-65-2324
Fax:
+81-462-65-2366
Table 25: Hirose sales contacts (subject to change)
Hirose Ltd.
For further information
please click:
http://www.hirose.com
Hirose Electric (U.S.A.) Inc
2688 Westhills Court
Simi Valley, CA 93065
U.S.A.
Phone: +1-805-522-7958
Fax:
+1-805-522-3217
Hirose Electric GmbH
Zeppelinstrasse 42
73760 Ostfildern
Kemnat 4
Germany
Phone: +49-711-4560-021
Fax
+49-711-4560-729
E-mail info@hirose.de
Hirose Electric UK, Ltd
Crownhill Business Centre
22 Vincent Avenue,
Crownhill
Milton Keynes, MK8 OAB
Great Britain
Phone:+44-1908-305400
Fax: +44-1908-305401
Hirose Electric Co., Ltd.
5-23, Osaki 5 Chome,
Shinagawa-Ku
Tokyo 141
Japan
Phone: +81-03-3491-9741
Fax:
+81-03-3493-2933
Hirose Electric Co., Ltd.
European Branche
First class Building 4F
Beechavenue 46
1119PV Schiphol-Rijk
Netherlands
Phone: +31-20-6557-460
Fax:
+31-20-6557-469
TC65_HD_V00.450
Page 90 of 96
20.04.2005
TC65 Hardware Interface Description
Strictly confidential / Draft
9.2
Fasteners and Fixings for Electronic Equipment
This section provides a list of suppliers and manufacturers offering fasteners and fixings for
electronic equipment and PCB mounting. The content of this section is designed to offer
basic guidance to various mounting solutions with no warranty on the accuracy and
sufficiency of the information supplied. Please note that the list remains preliminary although
it is going to be updated in later versions of this document.
9.2.1
Fasteners from German Supplier ETTINGER GmbH
Sales contact:
ETTINGER GmbH
http://www.ettinger.de/main.cfm
Phone:
+4981 04 66 23 – 0
Fax:
+4981 04 66 23 – 0
The following tables contain only article numbers and basic parameters of the listed
components. For further detail and ordering information please contact Ettinger GmbH.
Please note that some of the listed screws, spacers and nuts are delivered with the DSB75
Support Board. See comments below.
Article number: 05.71.038
Spacer - Aluminum /
Wall thickness = 0.8mm
Length
3.0mm
Material
AlMgSi-0,5
For internal diameter
M2=2.0-2.3
Internal diameter
d = 2.4mm
External diameter
4.0mm
Vogt AG No.
x40030080.10
TC65_HD_V00.450
Page 91 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
Article number: 07.51.403
Insulating Spacer for M2
Self-gripping *)
Length
3.0mm
Material
Polyamide 6.6
Surface
Black
Internal diameter
2.2mm
External diameter
4.0mm
Flammability rating
UL94-HB
*)
2 spacers are delivered with DSB75 Support Board
Article number: 05.11.209
Threaded Stud M2.5 - M2 Type E /
External thread at both ends
Length
3.0mm
Material
Stainless steel X12CrMoS17
Thread 1 / Length
M2.5 / 6.0mm
Thread 2 / Length
M2 / 8.0mm
Width across flats
Recess
yes
Type
External / External
TC65_HD_V00.450
Page 92 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
Article number: 01.14.131
Screw M2 *)
DIN 84 - ISO 1207
Length
8.0mm
Material
Steel 4.8
Surface
Zinced A2K
Thread
M2
Head diameter
D = 3.8mm
Head height
1.30mm
Type
Slotted cheese head screw
*)
2 screws are delivered with DSB75 Support Board
Article number: 01.14.141
Screw M2
DIN 84 - ISO 1207
Length
10.0mm
Material
Steel 4.8
Surface
Zinced A2K
Thread
M2
Head diameter
D = 3.8mm
Head height
1.30mm
Type
Slotted cheese head screw
TC65_HD_V00.450
Page 93 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
Article number: 02.10.011
Hexagon Nut *)
DIN 934 - ISO 4032
Material
Steel 4.8
Surface
Zinced A2K
Thread
M2
Wrench size / Ø
Thickness / L
1.6mm
Type
Nut DIN/UNC, DIN934
*)
9.3
2 nuts are delivered with DSB75 Support Board
Data Sheets of Recommended Batteries
The following two data sheets have been provided by VARTA Microbattery GmbH.
Click here for sales contacts and further information: http://www.varta-microbattery.com
TC65_HD_V00.450
Page 94 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
Figure 40: Lithium
Ion battery from
VARTA
TC65_HD_V00.450
Page 95 of 96
20.04.2005
s
TC65 Hardware Interface Description
Strictly confidential / Draft
Figure 41: Lithium
Polymer battery
from VARTA
TC65_HD_V00.450
Page 96 of 96
20.04.2005

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Modify Date                     : 2005:06:10 20:08:21+02:00
Create Date                     : 2005:06:10 20:07:57+02:00
Title                           : TC65
Author                          : DE18D000
Creator                         : Acrobat PDFMaker 6.0 for Word
Producer                        : Acrobat Distiller 6.0.1 (Windows)
Page Count                      : 48

EXIF Metadata provided by EXIF.tools