TRENDNET TEW818DRU AC1900 Dual Band Wireless Router User Manual test 3

Download:
Mirror Download [FCC.gov]
Document ID	2878610
Application ID	34lwALjjXSLsD52bAXbfUA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	160.24kB (2002994 bits)
Date Submitted	2016-01-20 00:00:00
Date Available	2016-01-26 00:00:00
Creation Date	2015-12-28 15:54:31
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2015-12-28 15:54:50
Document Title	test 3
Document Author:	Jonathan

TRENDnet User’s Guide
Cover Page
TRENDnet User’s Guide
Table of contents
Table of Contents
Change your router IP address .................................................................................... 23
Table of Contents ............................................................................2
Set up the DHCP server on your router ....................................................................... 24
Product Overview ...........................................................................4
Package Contents .......................................................................................................... 4
Features ......................................................................................................................... 4
Product Hardware Features........................................................................................... 5
Application Diagram ...................................................................................................... 7
Router Setup ...................................................................................7
Creating a Home Network ............................................................................................. 7
Router Installation ......................................................................................................... 8
Connect additional wired devices to your network ..................................................... 12
Wireless Networking and Security ................................................. 12
Set up DHCP reservation ............................................................................................. 24
Manually configure your Internet connection ............................................................ 25
Clone a MAC address ................................................................................................... 25
Add static routes to your router .................................................................................. 26
IPv6 Internet Connection Settings ............................................................................... 27
Prioritize traffic using QoS (Quality of Service) ........................................................... 28
Advanced wireless settings ......................................................................................... 29
Multiple SSID ..................................................................................................... 29
Wireless bridging using WDS (Wireless Distribution System) ........................... 31
Additional wireless settings ............................................................................... 32
Set your router date and time ..................................................................................... 33
How to choose the type of security for your wireless network .................................. 12
Create schedules ......................................................................................................... 33
Secure your wireless network ..................................................................................... 13
Access Control ............................................................................................................. 34
Connect wireless devices to your router ..................................................................... 15
Open a device on your network to the Internet .......................................................... 35
Connect wireless devices using WPS ........................................................................... 15
DMZ ................................................................................................................... 35
Virtual Server ..................................................................................................... 35
Special Applications ........................................................................................... 36
Gaming............................................................................................................... 37
Basic ............................................................................................. 17
Access your router management page ........................................................................ 17
Network Status ............................................................................................................ 17
Wireless settings .......................................................................................................... 18
Guest Network ............................................................................................................. 19
Enable/disable Application Layer Gateways (ALG) ...................................................... 38
Enable/disable UPnP on your router ........................................................................... 39
Using External USB Storage ........................................................... 39
Steps to improve wireless connectivity ....................................................................... 21
Samba Network File Server ......................................................................................... 39
Parental Control........................................................................................................... 21
FTP (File Transfer Protocol) Server .............................................................................. 40
Doman/URL Filters ............................................................................................. 22
IP Filters (LAN Client Filters) .............................................................................. 22
MAC Address Filters ........................................................................................... 22
ADVANCED ................................................................................... 23
© Copyright 2015 TRENDnet. All Rights Reserved.
Properly Eject USB device ............................................................................................ 41
Print Share Utility Installation ....................................................... 42
Windows Installation ................................................................................................... 42
MAC OS X Installation .................................................................................................. 43
TRENDnet User’s Guide
Launching the Utility .................................................................................................... 44
Utility Main Window .................................................................................................... 44
Table of contents
Allow/deny ping requests to your router from the Internet ....................................... 54
Check the router system information ......................................................................... 55
Configure Server .......................................................................................................... 45
Router Management Page Structure ............................................. 59
Connect ........................................................................................................................ 45
Technical Specifications ................................................................ 60
Disconnect ................................................................................................................... 45
Sending a Request to Connect ..................................................................................... 46
Connect to a Printer..................................................................................................... 47
Troubleshooting ........................................................................... 62
Appendix ...................................................................................... 63
Auto-Connect Printer ................................................................................................... 48
Connect to a Scanner ................................................................................................... 48
Router Maintenance & Monitoring................................................ 49
Change your router login password ............................................................................ 49
Change your device name ........................................................................................... 49
Change your device URL .............................................................................................. 50
Identify your network on the Internet......................................................................... 50
Allow remote access to your router management page ............................................. 51
Reset your router to factory defaults .......................................................................... 51
Router Default Settings ............................................................................................... 52
Backup and restore your router configuration settings .............................................. 52
Upgrade your router firmware .................................................................................... 53
Reboot your router ...................................................................................................... 54
© Copyright 2015 TRENDnet. All Rights Reserved.
TEW-818DRU
TRENDnet User’s Guide
network to connect common wireless devices. Use the high speed USB 3.0 port
and Gigabit Ethernet ports to further expand your network.
Product Overview
Ease of Use
Easy Setup
Get up and running in minutes with the intuitive guided setup
One Touch Connection
Securely connect to the router at the touch of the Wi-Fi Protected Setup (WPS)
button
USB Share Ports
Plug in a flash or storage drive into the 5 Gbps USB 3.0 port or the USB 2.0 port
Multi Language
Multi Language Interface: English, Spanish, French, German, and Russian
TEW-818DRU
Security
Package Contents
Encrypted Wireless
In addition to your router, the package includes:
For your security the router arrives pre-encrypted with its own unique password
Guest Network
Create a secure, isolated network for guest internet access only
Parental Controls
Control access to specific websites or types of content
CD-ROM (Utility and User’s Guide)
Multi-Language Quick Installation Guide
Network cable Ethernet Cable (1.5m / 5ft.)
Power Adapter (12V, 2A)
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
Features
TRENDnet’s AC1900 Dual Band Wireless Router, model TEW-818DRU, is an
extreme performance wireless router. It creates two concurrent wireless
networks—a 1.3 Gigabit Wireless AC network and a 600 Mbps Wireless N
© Copyright 2015 TRENDnet. All Rights Reserved.
Performance
Next Generation Wireless AC
802.11ac provides uninterrupted HD video streaming in a busy connected home
Simultaneous Dual Band
High speed 1300 Mbps Wireless AC band + 600 Mbps Wireless N
TEW-818DRU
TRENDnet User’s Guide
Gigabit Ports
Gigabit ports extend high performance wired connections
Wireless Coverage
Whole home wireless coverage for average size homes
Backward Compatible
Compatible with legacy wireless devices
Energy Savings
Embedded GREENnet technology reduces power consumption by up to 50%
Targeted Beamforming
Increased real-time performance by directing stronger wireless to your specific
location
*Maximum wireless signal rates are referenced from IEEE 802.11 theoretical
specifications. Actual data throughput and coverage will vary depending on
interference, network traffic, building materials and other conditions. 802.11n 2.4 GHz
TurboQAM speeds requires clients with TurboQAM support.
** Printer Control Center utility installation required for each computer in order to
access the printer
Product Hardware Features
Rear View
USB 3.0 Share
Port
WPS Button
USB 2.0 Share
Port
Gigabit LAN
Ports 1-4
On/Off Power Switch
(EU only)
Gigabit Internet
Port
Power Port
Reset Button (Located on Bottom)
x USB 3.0 and USB 2.0 Share Port: Connect a USB storage device to share files across
your network or connect a USB printer to share printers across your network
(Printer Control Center utility required for printer sharing).
x WPS Button (Wi-Fi Protected Setup): Push and hold this button for 5 seconds to
activate WPS. The Power LED will blink when WPS is activated.
x Gigabit LAN Ports 1-4: Connect Ethernet cables (also called network cables) from
your router LAN ports to your wired network devices.
x Gigabit Internet Port: Connect an Ethernet cable from your router Internet port to
your modem.
© Copyright 2015 TRENDnet. All Rights Reserved.
TEW-818DRU
TRENDnet User’s Guide
x On/Off Power Switch: Push the router On/Off power switch to turn your router
“On” (Inner position) or “Off” (Outer position). Available on EU version product
only.
x Power Port: Connect the included power adapter from your router power port and
to an available power outlet.
x Reset Button (Located on Bottom): Press and hold this button for 10 seconds to
reset the router.
USB 3.0 and USB 2.0 LED: The indicator turns green indicating a USB device is
connected and turns off when there is no USB device connected.
5GHz Wireless (Link/Activity) LED: The indicator turns on solid green when 5GHz
wireless is enabled on your router. The indicator will blink during when data is
transmitted or received by your 5GHz wireless client devices connected to your
router.
2.4GHz Wireless (Link/Activity) LED: The indicator turns on solid green when
2.4GHz wireless is enabled on your router. The indicator will blink when data is
transmitted or received by your 2.4GHz wireless client devices connected to your
router.
Front View
USB Share Port
LAN Ports 1-4 (Link/Activity) LED: These LED indicators are solid green when the
Gigabit LAN ports 1-4 (Black) are physically connected to your wired network
devices (which are turned on) with a network or Ethernet cable. These LED
indicators will blink green while data is transmitted or received through your
router’s Gigabit LAN ports.
5GHz Wireless LED
2.4GHz Wireless LED
LAN Ports 1-4 LEDs
Internet Port LED
Power/WPS LED
© Copyright 2015 TRENDnet. All Rights Reserved.
Internet Port (Link/Activity) LED – This LED indicator is solid green when your
router Gigabit Internet port is physically connected to the modem network or
Ethernet port with a network or Ethernet cable (modem turned on). The LED
indicator will be blinking green while data is transmitted or received through the
Gigabit Internet port of your router.
Power/WPS LED: The indicator is solid green when your router is powered on.
Otherwise if this LED indicator is off, there is no power to your router. The
indicator will also blink when WPS is activated. The LED will stop blinking and
remain solid green automatically once WPS process is completed.
TEW-818DRU
TRENDnet User’s Guide
Application Diagram
x Switch: Connect several wired network devices to your home network. Your router
has a built-in network switch (the LAN port 1-4). If you have more wired network
devices than available Ethernet ports on your router, you will need an additional
switch to add more wired connections.
How to set up a home network
1. For a network that includes Internet access, you’ll need:
The router is installed near the modem (typically supplied by your ISP “Internet Service Provider”)
and physically connected to it from the router’s Internet port to the modem’s network port which
connects to the Internet. 2.4GHz wireless signals from the router are broadcasted to wireless
clients such as laptops (with wireless capability) and the less congested 5GHz wireless signals from
the router are broadcasted to other wireless client devices such as TVs, game consoles, or media
bridges thereby providing Internet access for all wireless client devices, for faster 11ac
connection.
Router Setup
x Computers/devices with an Ethernet port (also called network port) or wireless
networking capabilities.
x A modem and Internet service to your home, provided by your ISP (modem
typically supplied by your ISP).
x A router to connect multiple devices to the Internet.
2. Make sure that your modem is working properly. Your modem is often provided by
your Internet Service Provider (ISP) when you sign up for Internet service. If your
modem is not working contact your ISP to verify functionality.
3. Set up your router. See “How to setup your router” below.
4. To connect additional wired computers or wired network devices to your network,
see “Connect additional wired devices to your network” on page 12.
Creating a Home Network
5. To set up wireless security on your router, see “Wireless Networking and Security” on
page 12.
What is a network?
How to setup your router
A network is a group of computers or devices that can communicate with each other. A
home network of more than one computer or device also typically includes Internet
access, which requires a router.
A typical home network may include multiple computers, a media player/server, a
printer, a modem, and a router. A large home network may also have a switch,
additional routers, access points, and many Internet-capable media devices such as TVs,
game consoles, and Internet cameras.
Refer to the Quick Installation Guide or continue to the next section “Router
Installation” on page 8 for more detailed installation instructions.
Where to find more help
In addition to this User’s Guide, you can find help below:
x http://www.trendnet.com/support (documents, downloads, and FAQs are available
from this Web page)
x Modem: Connects a computer or router to the Internet or ISP (Internet Service
Provider).
x Router: Connects multiple devices to the Internet.
© Copyright 2015 TRENDnet. All Rights Reserved.
TEW-818DRU
TRENDnet User’s Guide
Router Installation
Before you install
Many Internet Service Providers (ISPs) allow your router to connect to the Internet
without verifying the information fields listed below. Skip this section for now and if
your router cannot connect to the Internet using the standard installation process, come
back to this page and contact your ISP to verify required ISP specification fields listed
below.
1. Obtain IP Address Automatically (DHCP)
Host Name (Optional)
MAC Address: ___:___:___:___:___:___ Enter your PC’s MAC address (Optional)
DNS Servers Address 1: _____. _____._____._____ (Optional)
DNS Servers Address 2: _____. _____._____._____ (Optional)
2. Static/Fixed IP address
MAC Address: ___:___:___:___:___:___ Enter your PC’s MAC address (Optional)
IP Address: _____. _____._____._____ (e.g. 215.24.24.129)
Subnet Mask: _____. _____._____._____
Default Gateway IP Address: _____. _____._____._____
DNS Servers Address 1: _____. _____._____._____
DNS Servers Address 2: _____. _____._____._____
4. PPTP
Type (Dynamic IP/DHCP or Static IP)
PPTP Server: _____________________ (IP address)
IP Address: _____. _____._____._____ (e.g. 215.24.24.129)
Subnet Mask:_____. _____._____._____
Default Gateway:_____. _____._____._____
Server IP: _____. _____._____._____
DNS Servers Address 1: _____. _____._____._____
DNS Servers Address 2: _____. _____._____._____
User Name: _________
Password: ________________
5. L2TP
Type (Dynamic IP/DHCP or Static IP)
L2TP Server: _____________________ (IP address)
IP Address: _____. _____._____._____ (e.g. 215.24.24.129)
Subnet Mask:_____. _____._____._____
Default Gateway:_____. _____._____._____
Server IP: _____. _____._____._____
DNS Servers Address 1: _____. _____._____._____
DNS Servers Address 2: _____. _____._____._____
User Name: _________
Password: ________________
3. PPPoE to obtain IP automatically
User Name: _________
Password: ________________
© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Hardware Installation
TEW-818DRU
8. Verify that the status LED indicators on the front of the router are illuminated: Power,
Internet, one of the LAN ports (1,2,3,4) and Wireless Bands (2.4G,5G).
1. Verify that you have an Internet connection when connecting your computer directly
to your modem.
2. Turn off your modem.
3. Disconnect the Network cable from your computer to your modem.
4. Connect your modem to the router Internet port (yellow).
5. Connect your computer to one of the router LAN ports.
6. Connect the power adapter to the router and then to a power outlet.
7. Turn on your modem.
© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-818DRU
Internet Setup Wizard
4. The wizard will automatically begin when upon your initial setup. Click Next to begin.
1. Open your web browser (e.g. Internet Explorer, Firefox, Safari, Chrome, or Opera) and
go to http://TEW-818DRU or you can access the router management using the IP
address http://192.168.10.1.
2. Your router will prompt you for a user name and password. For added security, the
router is preconfigured with a unique password. You can find the Password on a
sticker on the side of the router and on the label on the bottom of the router.
5. Select “DHCP Connection (Dynamic IP Address)” and click Next to continue.
Note: Dynamic IP (DHCP) is typical for most Internet services. You can verify your
settings with your Internet Service Provider.
3. Enter your Username and Password, select your preferred language, then click Login.
6. Confirm your Internet connection type and wireless interface settings. Click Apply to
save settings.
User Name: admin
Password: (xxxxxxxx)
Note: User Name and Password are case sensitive.
© Copyright 2015 TRENDnet. All Rights Reserved.
10
TRENDnet User’s Guide
TEW-818DRU
10. For added security, the router is pre-encrypted with its own unique wireless network
security key. You can find the unique network security key and pre-assigned network
name (SSID) on a sticker on the front of the router and on a label on the bottom of the
router. If you would like to change the wireless settings, continue to the next page to
launch the wireless setup wizard.
7. Click OK when prompted.
9. Open a new tab on your web browser and enter in a website (e.g.
www.trendnet.com) to verify that you have an Internet connection.
© Copyright 2015 TRENDnet. All Rights Reserved.
11
TEW-818DRU
TRENDnet User’s Guide
Connect additional wired devices to your network
Wireless Networking and Security
You can connect additional computers or other network enabled devices to your
network by using Ethernet cables to connect them to one of the available LAN ports
labeled 1,2,3,4 on your router. Check the status of the LED indicators (1, 2, 3, or 4) on
the front panel of your router to ensure the physical cable connection from your
computer or device.
How to choose the type of security for your wireless network
Note: If you encounter issues connecting to your network, there may be a problem with
your computer or device network settings. Please ensure that your computer or device
network settings (also called TCP/IP settings) are configured to obtain IP address settings
automatically (also called dynamic IP address or DHCP) and to Obtain DNS Server
address settings automatically.
Setting up wireless security is very important. Leaving your wireless network open and
unsecure could expose your entire network and personal files to outsiders. TRENDnet
recommends reading through this entire section and setting up wireless security on your
new router.
There are a few different wireless security types supported in wireless networking each
having its own characteristics which may be more suitable for your wireless network
taking into consideration compatibility, performance, as well as the security strength
along with using older wireless networking hardware (also called legacy hardware).
It is strongly recommended to enable wireless security to prevent unwanted users from
accessing your network and network resources (personal documents, media, etc.).
In general, it is recommended that you choose the security type with the highest
strength and performance supported by the wireless computers and devices in your
network. Please review the security types to determine which one you should use for
your network.
Wireless Encryption Types
x WEP: Legacy encryption method supported by older 802.11b/g hardware. This is
the oldest and least secure type of wireless encryption. It is generally not
recommended to use this encryption standard, however if you have old 802.11 b or
802.11g wireless adapters or computers with old embedded wireless cards(wireless
clients), you may have to set your router to WEP to allow the old adapters to
connect to the router.
Note: This encryption standard will limit connection speeds to 54Mbps.
x WPA: This encryption is significantly more robust than the WEP technology. Much
of the older 802.11g hardware was been upgraded (with firmware/driver upgrades)
to support this encryption standard. Total wireless speeds under this encryption
type however are limited to 54Mbps.
x WPA-Auto: This setting provides the router with the ability to detect wireless
devices using either WPA or WPA2 encryption. Your wireless network will
automatically change the encryption setting based on the first wireless device
connected. For example, if the first wireless client that connects to your wireless
network uses WPA encryption your wireless network will use WPA encryption. Only
when all wireless clients disconnect to the network and a wireless client with WPA2
encryption connects your wireless network will then change to WPA2 encryption.
© Copyright 2015 TRENDnet. All Rights Reserved.
12
TEW-818DRU
TRENDnet User’s Guide
Note: WPA2 encryption supports 802.11n speeds and WPA encryption will limit
your connection speeds to 54Mbps
x WPA2: This is the most secure wireless encryption available today, similar to WPA
encryption but more robust. This encryption standard also supports the highest
connection speeds. TRENDnet recommends setting your router to this encryption
standard. If you find that one of your wireless network devices does not support
WPA2 encryption, then set your router to either WPA or WPA-Auto encryption.
Note: Check the specifications of your wireless network adapters and wireless
appliances to verify the highest level of encryption supported. Below is brief
comparison chart of the wireless security types and the recommended
configuration depending on which type you choose for your wireless network.
Security Standard
Compatible
Wireless
Standards
Highest
Performance
Under This
Setting
Encryption
Strength
Additional
Options
Recommended
Configuration
WEP
Secure your wireless network
Wireless (2.4GHz or 5GHz)> Security
After you have determined which security type to use for your wireless network (see
“How to choose the security type for your wireless network” on page 12), you can set up
wireless security.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Wireless button.
WPA
IEEE 802.11a/b/g
(802.11n devices
will operate at
802.11g to connect
using this
standard)
IEEE 802.11a/b/g/n
Up to 54Mbps
Up to 54Mbps
Up to 450Mbps (11n)
and up to 1.3Gbps
(11ac)*
Low
Open System or
Shared Key,
HEX or ASCII,
Different key sizes
Medium
High
Selecting WEP-OPEN, WEP-SHARED:
TKIP or AES,
Preshared Key or
RADIUS
TKIP or AES,
Preshared Key or
RADIUS
If selecting WEP (Wired Equivalent Privacy), please review the WEP settings to configure
and click Apply to save the changes.
TKIP
Preshared Key
8-63 characters
AES
Preshared Key
8-63 characters
IEEE 802.11a/b/g
(802.11n devices
will operate at
802.11g to connect
using this standard)
Open System ASCII
13 characters
WPA2
3. Underneath the basic wireless band section, you will see Security Mode. Click on the
drop-down list to select your wireless security type.
*Dependent on the maximum 802.11n/ac data rate supported by the device (150Mbps,
300Mbps, 450Mbps, 867Mbps, or 1.3Gbps)
© Copyright 2015 TRENDnet. All Rights Reserved.
Note: WEP security is only available in the Security Mode list when 802.11 n-mode is set
to Off under Wireless (2.4GHz or 5GHz) > Basic.
Note: WPS functionality is not available when using WEP.
In the Security Mode drop-down list, select WEP-OPEN or WEP-SHARED.
Note: It is recommended to use WEP-OPEN because it is known to be more secure than
Shared Key.
13
TEW-818DRU
TRENDnet User’s Guide
Selecting WPA-PSK, WPA2-PSK, WPA2-PSK, or Mixed (WPA2-PSK recommended):
In the Security Mode drop-down list, select WPA-.
x Current Network Key - You can define up to 4 keys however, only one key can be
active at any given time. Most users simply define one key. Click the drop-down list
to select which of the 4 keys is the active key.
WEP Key Format
HEX
ASCII
Character set
0-9 & A-F, a-f only
Alphanumeric (a,b,C,?,*, /,1,2, etc.)
64-bit key length
10 characters
5 characters
128-bit key length
26 characters
13 characters
x Network Key 1-4
o This is where you enter the WEP key needed for a computer to connect to the
router wirelessly
o You can define up to 4 passwords or 4 keys. Only one key can be active at a given
time. Most users simply define one key.
o Choose a key index 1, 2, 3, or 4 and enter the key.
o When connecting to the router, the client must match both the password and the
Key number. (e.g. if you have activated Key 2 with a password of 12345, then the
client must select: Key 2 (entering Key 1, 3, or 4 will block the ability to connect)
and enter password 12345)
The following section outlines options when selecting WPA-PSK, WPA2-PSK, or WPA2PSK Mixed (Preshared Key Protocol),
x WPA Encryption: Select a Cipher Type to use. When selecting WPA-PSK security, it
is recommended to use TKIP + AES.
o When selecting WPA2-PSK Mixed security, it is recommended to use TKIP+AES.
o When selecting WPA2-PSK security, it is recommended to use AES.
x WPA passphrase: Enter the passphrase.
o This is the password or key that is used to connect your computer to this router
wirelessly
Note: 8-63 alphanumeric characters (a,b,C,?,*, /,1,2, etc.)
x Network Key Rotation Interval: Enter the time interval (seconds) of when the
network passphrase will rotate. Note: It is recommended to use the default interval
time. Your passphrase will not change, rotation of the key is part of the WPA
protocol and designed to increase security.
Selecting WPA, WPA2, or WPA2 Mixed:
Note: It is recommended to use 128-bit format because it is more secure to use a
key that consists of more characters.
x Click here to display - Typically, the password characters are masked for security
purposes. This link displays actual characters of the currently assigned password for
your reference.
© Copyright 2015 TRENDnet. All Rights Reserved.
14
TEW-818DRU
TRENDnet User’s Guide
The following section outlines options when selecting WPA. WPA2 or WPA2 Mixed
known as EAP (Extensible Authentication Protocol). Also known as called Remote
Authentication Dial-In User Service or RADIUS.
Connect wireless devices using WPS
Note: This security type requires an external RADIUS server, PSK only requires you to
create a passphrase.
x RADIUS Server: Enter the IP address of the RADIUS server. (e.g. 192.168.10.250)
x RADIUS Port: Enter the port your RADIUS server is configured to use for RADIUS
authentication.
Note: It is recommended to use port 1812 which is typical default RADIUS port.
x RADIUS Key: Enter the shared secret used to authorize your router with your
RADIUS server.
WPS (Wi-Fi Protected Setup) is a feature that makes it easy to connect devices to your
wireless network. If your wireless devices support WPS, you can use this feature to
easily add wireless devices to your network.
Connect wireless devices to your router
A variety of wireless network devices can connect to your wireless network such as:
Gaming Consoles
Internet enabled TVs
Network media players
Smart Phones
Wireless Laptop computers
Wireless IP cameras
Each device may have its own software utility for searching and connecting to available
wireless networks, therefore, you must refer to the User’s Manual/Guide of your
wireless client device to determine how to search and connect to this router’s wireless
network.
See the “Appendix” on page 63 for general information on connecting to a wireless
network.
Note: You will not be able to use WPS if you set the SSID Broadcast setting to Disabled or
if you are using WEP security.
There are two methods the WPS feature can easily connect your wireless devices to
your network.
x Push Button Configuration (PBC) method
o (RECOMMENDED) Hardware Push Button method–with an external button
located physically on your router and on your client device
o WPS Software/Virtual Push Button - located in router management page
x PIN (Personal Identification Number) Method - located in router management page
Note: Refer to your wireless device documentation for details on the operation of
WPS.
Recommended Hardware Push Button (PBC) Method
Note: It is recommended that a wireless key (passphrase or password) is created
before connecting clients using the PBC method. If no wireless key is defined when
connecting via PBC, the router will automatically create an encryption key that is 64
characters long. This 64 character key will then have to be used if one has to
connect computers to the router using the traditional connection method.
To add a wireless device to your network, simply push the WPS button on the wireless
device you are connecting (consult client device User’s Guide for length of time), then
push and hold the WPS button located on your router for 3 seconds and release it. A
blue LED on your router WPS button will flash indicating that the WPS setup process has
been activated on your router. (See “Product Hardware Features” on page 5)
For connecting additional WPS supported devices, repeat this process for each
additional device.
© Copyright 2015 TRENDnet. All Rights Reserved.
15
TEW-818DRU
TRENDnet User’s Guide
PBC (Software/Virtual Push Button)
PIN (Personal Identification Number)
Wireless (2.4GHz or 5GHz)> WPS
Wireless (2.4GHz or 5GHz)> WPS
In addition to the hardware push button located physically on your router, the router
management page also has push button which is a software or virtual push button you
can click to activate WPS on your router.
If your wireless device has WPS PIN (typically an 8-digit code printed on the wireless
device product label or located in the wireless device wireless software utility), you can
use this method.
1. Log into your router management page (see “Access your router management page”
on page 17).
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
2. Click on the wireless band Wireless (2.4GHz or 5GHz) you would like to configure and
click on WPS.
3. Select wireless band you would like to configure, Wireless 2.4GHz or Wireless 5GHz
and click on WPS.
3. Next to Station PIN, enter the WPS PIN of the wireless device you are connecting and
click the Add Enrollee button.
4. To add a wireless device to your network, simply click the Add Enrollee button in the
router management page, then push the WPS button on the wireless device (consult
wireless device’s User’s Guide for length of time) you are connecting.
© Copyright 2015 TRENDnet. All Rights Reserved.
Note: You may need to initiate the WPS PIN on your wireless device first when using
this method. Refer to your wireless device documentation for details on the
operation of WPS.
16
TEW-818DRU
TRENDnet User’s Guide
Basic
Access your router management page
Note: Your router management page URL/domain name http://TEW-818DRU or IP
address http://192.168.10.1 is accessed through the use of your Internet web browser
(e.g. Internet Explorer, Firefox, Chrome, Safari, Opera) and will be referenced frequently
in this User’s Guide.
1. Open your web browser (e.g. Internet Explorer, Firefox, Safari, Chrome, or Opera) and
go to URL/domain name http://TEW-818DRU or IP address http://192.168.10.1. Your
router will prompt you for a user name and password.
x User Name: admin
x Password: (xxxxxxxx)
Note: User Name and Password are case sensitive.
Network Status
2. For added security, the router is preconfigured with a unique password. You can find
the Password on a sticker on the side of the router and on the label on the bottom of
the router.
This screen appears when you login into your router. This section provides an over view
of your.
3. Enter your Username and Password, select your preferred language, then click Login.
© Copyright 2015 TRENDnet. All Rights Reserved.
17
TEW-818DRU
TRENDnet User’s Guide
Wireless settings
Internet: This icon turns green to indicate that your network has a valid
Internet connection. Amber color indicates a physical connection on the
Internet port of the router but with no valid Internet connection. Red color
indicates disconnected Internet port.
Wireless (2.4GHz or 5GHz)> Basic
This section outlines available management options under basic wireless sub tab for
both 2.4GHz and 5GHz wireless sections.
1. Log into your router management page (see “Access your router management page”
on page 17).
Guest Network: The section provides your router’s guest network SSID.
2. Click on Wireless and under the Basic tab.
USB: This icon turns green when your router has a valid USB connection. Red
Amber color indicates no USB connection.
3. To save changes to this section, click Apply when finished.
Wireless: This icon turns green to indicate when your router’s wireless
network is enabled. Red color indicates your router’s wireless network is
disabled.
Security: This section provides your router’s wireless network security
information.
Connected Devices: This section provides information of all connected
devices on your router.
© Copyright 2015 TRENDnet. All Rights Reserved.
x Radio On/Off:
o On: Turns on wireless radio.
o Off: Turns off wireless radio.
x Wireless Name (SSID): Enter the wireless name (SSID) for your wireless network.
This acronym stands for Service Set Identifier and is the name of your wireless
network. It differentiates your wireless network from others around you. By
default, the router’s wireless name is unique to the device. If you choose to change
the SSID, change it to a name that you can easily remember.
x 802.11 n-mode
o Auto: Select this option if you have non-802.11n wireless clients (802.11a/b/g)
connecting to your wireless network.
18
TEW-818DRU
TRENDnet User’s Guide
o Off: The router will operate in 802.11n mode only, non-802.11n wireless clients
will not be able to connect when this option is selected.
When applying the 802.11 n-mode setting on 2.4GHz, please keep in mind the following:
x Wireless devices that support 802.11n are backwards compatible and can connect
wirelessly at 802.11g or 802.11b.
x Connecting at 802.11b or 802.11g will limit the capability of your 802.11n
supported wireless devices from obtaining higher performance and data rates.
x Allowing 802.11b or 802.11g devices to connect to an 802.11n capable wireless
network may degrade the wireless network performance below the higher
performance and data rates of 802.11n.
x Wireless devices that only support 802.11b or 802.11g will not be able to connect
to a wireless network that is set to 802.11n only mode.
x Wireless devices that only support 802.11b will not be able to connect to a wireless
network that is set to 802.11g only mode.
x Broadcast Network Name (SSID):
o Enabled allows wireless devices to search and discover your wireless network
name (also called SSID) broadcasted by your router.
o Disabled turns off the ability for wireless devices to find your network. It is still
possible for wireless devices to be configured to connect to your wireless
network. Disabling this setting will disable WPS functionality.
x Frequency (Channel): To manually set the channel on which the router will
broadcast, click the drop-down list and select the desired Channel for wireless
communication. The goal is to select the Channel that is least used by neighboring
wireless networks.
x Channel Bandwidth: Select the appropriate channel width for your wireless
network. This setting only applies to 802.11n and 802.11ac. For greater 802.11n
performance in 2.4GHz, select 40MHz (Options: 20MHz or 40MHz). For greater
802.11ac performance in 5GHz, select 80MHz (Options: 20MHz, 40MHz, or 80MHz)
It is recommended to use the default channel bandwidth settings.
Note: Please note that this setting may provide more stability than the higher
channel bandwidth settings such as 40 MHz or 80MHz for connectivity in busy
wireless environments where there are several wireless networks in the area.
20 MHz: This mode operates using a single 20MHz channel for wireless devices
connecting at 802.11n on both 2.4GHz and 5GHz. This setting may provide more
stability than 40MHz or 80MHz for connectivity in busy wireless environments
where there are several neighboring wireless networks in the area.
40 MHz or 80MHz:When 40MHz or 80MHz is active, this mode is capable of
providing higher performance only if the wireless devices support the channel
© Copyright 2015 TRENDnet. All Rights Reserved.
bandwidth settings. Enabling 40MHz or 80MHz typically results in substantial
performance increases when connecting an 802.11n or 802.11ac client. Note:
Please note that 80MHz channel bandwidth is only available for 802.11ac 5GHz.
Guest Network
Wireless (2.4GHz or 5GHz) > Guest Network
Creating an isolated and separate wireless guest network (2.4GHz or 5GHz) allows
wireless clients to connect to your network for Internet access only and keep your local
LAN network safe by restricting guest access to your LAN network resources such as
shared documents and media files on your computers, network storage, and printers.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Basic tab.
3. Click on Guest Network section.
4. Review the Guest Network settings, click Apply when finished.
x Enabled: Check the option to enable the Guest Network.
19
TEW-818DRU
TRENDnet User’s Guide
x Wireless Name (SSID): This acronym stands for Service Set Identifier and is the
name of your wireless network. It differentiates your wireless network from others
around you. It is recommended to use a different name from your primary wireless
network to a name that you can easily identify and differentiate from the primary.
You can reference your guests to access this network instead of the primary.
x Internet Access Only: By default, the option is checked to allow guests to only
access the Internet and restrict access to your local LAN network. Please note that
unchecking this option will open access to local LAN network to guests.
x Wireless Client Isolation: Checking this option will restrict guests from
communicating with each other over the guest network such as share files.
5. Under Security Policy, you can apply a different wireless security type and key to the
guest network. Please refer to page 15 to find out about different security types and
page 16 for wireless security configuration.
(e.g. 192.168.100.1)
x Subnet Mask – Enter the new guest network subnet mask.
(e.g. 255.255.255.0)
Note: If you are not encountering any issues or are not faced with one of the cases
described above or similar, it is recommended to keep your guest network sIP address
settings as default. The guest network IP address settings should different from your
local LAN network IP address settings (Default: 192.168.10.1 / 255.255.255.0)
Your router can be used as a DHCP (Dynamic Host Configuration Protocol) server to
automatically assign an IP address to each computer or device on your guest network.
The DHCP server is enabled by default on your router. It is recommended to leave this
setting enabled.
Advanced Guest Network Settings
Wireless (2.4GHz or 5GHz) > Guest Network>Advanced Guest Network Settings
At the bottom of the guest network page, you can click the “Advanced Guest Network
Settings” to configure the additional guest network options such as the guest network
interface IP address, DHCP server IP address range, and DHCP reservation.
Review the Advanced Guest Network settings, click Apply when finished.
x DHCP Server – Enable or Disable the DHCP server.
x DHCP Start IP – Changes the starting address for the DHCP server range. (e.g.
192.168.20.20)
x DHCP End IP – Changes the last address for the DHCP server range. (e.g.
192.168.20.30)
x Lease Time – Enter the lease time in seconds.
DHCP (Dynamic Host Configuration Protocol) reservation (also called Static DHCP) allows
your router to assign a fixed IP address from the DHCP server IP address range to a
specific device on your guest network.
In most cases, you do not need to change your guest network IP address settings.
Typically, the router IP address settings only needs to be changed, if you plan to use
another router in your network with the same IP address settings, if you are connecting
your router to an existing network that is already using the IP address settings your
router is using, or if you are experiencing problems establishing VPN connections to
your office network through your router.
x IP Address – Enter the new guest network IP address.
© Copyright 2015 TRENDnet. All Rights Reserved.
20
TEW-818DRU
TRENDnet User’s Guide
x Hostname: Enter a name of the device you will assign the DHCP reservation rule.
x MAC Address: Enter the MAC (Media Access Control) address of the computer or
network device to assign to the reservation. (e.g. 00:11:22:AA:BB:CC)
x IP Address: Enter the IP address to assign to the reservation. (e.g.
192.168.10.101)
x Enable: Select enable to enable the setting
Steps to improve wireless connectivity
There are a number of factors that can impact the range of wireless devices. Follow
these tips to help improve your wireless connectivity:
1. Keep the number of obstructions to a minimum. Each obstruction can reduce the
range of a wireless device. Position the wireless devices in a manner that will
minimize the amount of obstructions between them.
a. For the widest coverage area, install your router near the center of your home,
and near the ceiling, if possible.
b. Avoid placing the router on or near metal objects (such as file cabinets and
metal furniture), reflective surfaces (such as glass or mirrors), and masonry
walls.
c. Any obstruction can weaken the wireless signal (even non-metallic objects), so
the fewer obstructions between the router and the wireless device, the better.
d. Place the router in a location away from other electronics, motors, and
fluorescent lighting.
e. Many environmental variables can affect the router’s performance, so if your
wireless signal is weak, place the router in several locations and test the signal
strength to determine the ideal position.
© Copyright 2015 TRENDnet. All Rights Reserved.
2. Building materials can have a large impact on your wireless signal. In an indoor
environment, try to position the wireless devices so that the signal passes through
less dense material such as dry wall. Dense materials like metal, solid wood, glass
or even furniture may block or degrade the signal.
3. Antenna orientation can also have a large impact on your wireless signal. Use the
wireless adapter’s site survey tool to determine the best antenna orientation for
your wireless devices.
4. Interference from devices that produce RF (radio frequency) noise can also impact
your signal. Position your wireless devices away from anything that generates RF
noise, such as microwaves, radios and baby monitors.
If possible, upgrade wireless network interfaces (such as wireless cards in computers)
from older wireless standards to 802.11n or 802.11ac. If a wirelessly networked device
uses an older standard, the performance of the entire wireless network may be slower.
If you are still experiencing low or no signal consider repositioning the wireless devices,
installing additional access points or wireless extenders.
Parental Control
This section outlines available management options under basic wireless sub tab for
both 2.4GHz and 5GHz wireless sections.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Basic tab.
3. Click on the Parental Control section.
21
TEW-818DRU
TRENDnet User’s Guide
Doman/URL Filters
Basic > Parent Control
Review the settings under IP Filter Rules section. Click Apply to save settings. Under the
IP Filter Mode drop-down list and select Enabled to activate the feature.
You may want to block computers or devices on your network access to specific
websites (e.g. www.trendnet.com, etc.), also called domains or URLs (Uniform Resource
Locators). You may also enter a keyword (e.g. instead of complete URL to generally
block computers or devices access to websites that may contain the keyword in the URL
or on the web page.
Review the settings under Web URL Filter Rules section. Click Apply to save settings.
Under Web URL Filter drop-down menu select Enabled to activate the feature.
x URL: Enter the Website/URL/domain (e.g.www.trendnet.com) or keyword (e.g.
trendnet) to block.
x Schedule: Click the drop-down list to select the pre-defined schedule to apply.
The filter will only be active during the time period defined in the pre-defined
schedule. (See “Create Schedule” section on page 33).
Note: Before applying scheduling, please ensure your Time settings are configured
correct and you have defined a schedule. See page 37 to configure Time Settings
and see page 38 to create a schedule.
Enabled: Checking the Enabled option activates on the URL filter rule.
x LAN IP Address Range: Enter the IP address or IP address range to apply the
protocol (e.g. 192.168.10.20-192.168.10.20 or 192.168.10.20-192.168.10.30).
Note: The filter will not be applied to IP addresses outside of the range specified.
Protocol – Select the protocol type to filter. TCP, UDP.
x Schedule: Click the drop-down list to select the pre-defined schedule to apply.
The filter will only be active during the time period defined in the pre-defined
schedule. (See “Create Schedule” section on page 33).
Note: Before applying scheduling, please ensure your Time settings are configured
correct and you have defined a schedule. See page 37 to configure Time Settings
and see page 38 to create a schedule.
x Enabled: Checking the Enabled option activates on the LAN Client Filter rule.
MAC Address Filters
Basic > Parent Control
Every network device has a unique, 12-digit MAC (Media Access Control) address. Using
MAC filters, you can allow or deny specific computers and other devices from using this
router’s wired network.
IP Filters (LAN Client Filters)
Basic > Parent Control
Review the settings under MAC Filter section. Click Apply to save settings.
You may want to block computers or devices on your network access to specific ports
(used or required by a specific application) to the Internet.
© Copyright 2015 TRENDnet. All Rights Reserved.
22
TEW-818DRU
TRENDnet User’s Guide
ADVANCED
Change your router IP address
Advanced > Setup > LAN Setting
In most cases, you do not need to change your router IP address settings. Typically, the
router IP address settings only needs to be changed, if you plan to use another router in
your network with the same IP address settings, if you are connecting your router to an
existing network that is already using the IP address settings your router is using, or if
you are experiencing problems establishing VPN connections to your office network
through your router.
x MAC Filter Mode: Select the option you would like to apply to the listed MAC
address.
o Disabled: Select this option to disable MAC filter rule.
o Deny: Select this option to deny listed MAC addresses.
o Allow: Select this option to only allow listed MAC addresses.
x MAC Filters: Enter the MAC address of the devices you would like to filter. (e.g.
00:11:22:AA:BB:CC)
Note: Enter the Add the MAC addresses to the MAC Table first before applying the
MAC filter function.
x Interface: Select the interface of the MAC address filter
o LAN: Local Access Network, wired clients
o WLAN: Wireless Local Access Network, wireless clients
o Both: Select this option if you uncertain which interface to use.
Note: MAC filter can be configured to allow access to the listed MAC address and
deny all others unlisted or vice versa. The recommended function is to choose to
only allow access to the MAC addresses listed and deny all others unlisted because it
is easier to determine the MAC addresses of devices in your network then to
determine which MAC addresses you do not want to allow access. You can check the
DHCP Client List for the MAC addresses of the devices on your network, see page 56
or refer to your computer or device documentation to find the MAC address.
Note: If you are not encountering any issues or are not faced with one of the cases
described above or similar, it is recommended to keep your router IP address
settings as default.
Default Router IP Address: 192.168.10.1
Default Router Network: 192.168.10.0 / 255.255.255.0
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
3. Click on the Setup section and click on LAN Setting.
4. In LAN Interface Setting section, Enter the router IP address settings. Click Apply to
save settings.
© Copyright 2015 TRENDnet. All Rights Reserved.
23
TEW-818DRU
TRENDnet User’s Guide
Note: The DHCP address range will change automatically to your new router IP
address settings so you do not have to change the DHCP address range manually to
3. Click on the Setup section and click on LAN Setting.
match your new router IP address settings.
3. Review the DHCP Server settings. Click Apply to save settings.
x IP Address: Enter the new router IP address. (e.g. 192.168.200.1)
x Subnet Mask: Enter the new router subnet mask. (e.g. 255.255.255.0)
Note: You will need to access your router management page using your new
router IP address. (e.g. Instead of using the default http://192.168.10.1 your new
router IP address will use the following format using your new IP address
http://(new.ipaddress.here) to access your router management page. You can
also use the default login URL http://TEW-818DRU
Set up the DHCP server on your router
N Advanced > Setup > LAN Setting
Your router can be used as a DHCP (Dynamic Host Configuration Protocol) server to
automatically assign an IP address to each computer or device on your network. The
DHCP server is enabled by default on your router. If you already have a DHCP server on
your network, or if you do not want to use your router as a DHCP server, you can disable
this setting. It is recommended to leave this setting enabled.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
x DHCP Server: Enable or Disable the DHCP server.
x DHCP Start IP: Changes the starting address for the DHCP server range.
(e.g.192.168.10.20)
x DHCP End IP: Changes the last address for the DHCP server range. (e.g.
192.168.10.30)
Note: The Start IP and End IP specify the range of IP addresses to automatically
assign to computers or devices on your network.
x DHCP Lease Time: Click the drop-down list to select the lease time.
Note: The DHCP lease time is the amount of time a computer or device can keep an
IP address assigned by the DHCP server. When the lease time expires, the computer
or device will renew the IP address lease with the DHCP server, otherwise, if there is
no attempt to renew the lease, the DHCP server will reallocate the IP address to be
assigned to another computer or device.
Set up DHCP reservation
Network > LAN Setting
DHCP (Dynamic Host Configuration Protocol) reservation (also called Static DHCP) allows
your router to assign a fixed IP address from the DHCP server IP address range to a
© Copyright 2015 TRENDnet. All Rights Reserved.
24
TEW-818DRU
TRENDnet User’s Guide
specific device on your network. Assigning a fixed IP address can allow you to easily
keep track of the IP addresses used on your network by your computers or devices for
future reference or configuration such as virtual server (also called port forwarding, see
“Virtual Server” on page 35) or special applications (also called port triggering, see
“Special Applications” on page 36).
Manually configure your Internet connection
Advanced > Setup > WAN Setting
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
3. Click on the Setup section and click on WAN Setting.
3. Click on the Setup section and click on LAN Setting.
4. In the WAN Connection Type drop-down list, click the type of Internet connection
provided by your Internet Service Provider (ISP).
3. Review the DHCP reservation settings. Click Apply to save settings.
5. Complete the fields required by your ISP.
x Hostname: Enter a name of the device you will assign the DHCP reservation rule.
x MAC Address: Enter the MAC (Media Access Control) address of the computer or
network device to assign to the reservation. (e.g. 00:11:22:AA:BB:CC)
x IP Address: Enter the IP address to assign to the reservation. (e.g. 192.168.10.101)
x Enable: Check the Enabled option to enable the reservation.
6. Complete the optional settings only if required by your ISP.
7. To save changes, click Apply.
Note: If you are unsure which Internet connection type you are using, please contact
your ISP.
Clone a MAC address
Advanced > Setup > WAN Setting
© Copyright 2015 TRENDnet. All Rights Reserved.
25
TEW-818DRU
TRENDnet User’s Guide
On any home network, each network device has a unique MAC (Media Access Control)
address. Some ISPs register the MAC address of the device (usually a router or a
computer) connected directly to the modem. If your computer MAC address is already
registered with your ISP and to prevent the re-provisioning and registration process of a
new MAC address with your ISP, then you can clone the address (assign the registered
MAC address of your previous device to your new router). If you want to use the MAC
address from the previous device (computer or old router that directly connected to the
modem, you should first determine the MAC address of the device or computer and
manually enter it into your router using the clone MAC address feature.
Note: For many ISPs that provide dynamic IP addresses automatically, typically, the
stored MAC address in the modem is reset each time you restart the modem. If you
are installing this router for the first time, turn your modem before connecting the
router to your modem. To clear your modem stored MAC address, typically the
procedure is to disconnect power from the modem for approximately one minute,
then reconnect the power. For more details on this procedure, refer to your
modem’s User Guide/Manual or contact your ISP.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
Note: You can check the DHCP Client List for the MAC addresses of the devices on
your network, see page 36 or refer to your computer or device documentation to
find the MAC address.
Add static routes to your router
Advanced > Setup > Routing
You may want set up your router to route computers or devices on your network to
other local networks through other routers. Generally, different networks can be
determined by the IP addressing assigned to those networks. Generally speaking and for
the case of an example, your network may have 192.168.10.x IP addressing and another
network may have 192.168.20.x IP addressing and because the IP addressing of these
two networks are different, they are separate networks. In order to communicate
between the two separate networks, static routing needs to be configured. Below is an
example diagram where routing is needed for devices and computers on your network
to access the other network.
Note: Configuring this feature assumes that you have some general networking
knowledge.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
3. Click on the Setup section and click on WAN Setting.
3. Click on the Setup section and click on Routing.
4. Next to MAC Address field, enter the MAC address of your computer. Click Apply to
save settings
© Copyright 2015 TRENDnet. All Rights Reserved.
26
TEW-818DRU
TRENDnet User’s Guide
4. Review the LAN/WAN Static Routes section. Click Apply to save settings.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
x IP Address: Enter the IP network address of the destination network for the route.
(e.g. 192.168.20.0)
x Subnet Mask: Enter the subnet mask of the destination network for the route.
(e.g. 255.255.255.0)
x Gateway: Enter the gateway to the destination network for the route.
(e.g. 192.168.10.2)
x Metric: Enter the metric or priority of the route. The metric range is 1-15, the
lowest number 1 being the highest priority. (e.g. 1 )
IPv6 Internet Connection Settings
Advanced > Setup > IPv6 Setting
IPv6 (Internet Protocol Version 6) is a new protocol that significantly increases the
number of available Internet public IP addresses due to the 128-bit IP address structure
versus IPv4 32-bit address structure. In addition, there are several integrated
enhancements compared to the most commonly used and well known IPv4 (Internet
Protocol Version 4) such as:
Integrated IPsec – Better Security
Integrated Quality of Service (QoS) – Lower latency for real-time applications
Higher Efficiency of Routing – Less transmission overhead and smaller routing tables
Easier configuration of addressing
Note: In order to use IPv6 Internet connection settings, it is required that your ISP
provide you with the IPv6 service. Please contact your ISP for availability and more
information about the IPv6 service.
© Copyright 2015 TRENDnet. All Rights Reserved.
3. Click on the Setup section and click on IPv6 Setting.
4. Review the IPv6 Internet Connection settings and enter information settings specified
by your ISP.
In WAN IPv6 Setting section, enter your IPv6 settings provided by your ISP (Internet
Service Provider) to configure your router’s IPv6 WAN settings. Click Apply to save
settings.
In LAN IPv6 Setting section, enter your IPv6 settings you would like to apply to your
LAN (Local Area Network). Click Apply to save settings.
27
TEW-818DRU
TRENDnet User’s Guide
3. Click on the Setup section and click on IPv6 Setting.
x Mode
o Disabled: IPv6 will be disabled when this option is selected
o 6to4 Only: 6to4 is provided as a transitional mechanism for migrating from IPv4
to IPv6. It allows IPv6 packets to be transmitted over an IPv4 network through
the automatic tunneling technology and routes traffic between 6to4 and IPv6
networks.
o Native IPv6 only: Native IPv6 refers to a network where IPv6 is the only transport
protocol.
o 6to4 + Native IPv6: Supports 6to4 and Native IPv6 simultaneously.
4. Review the QoS settings.
x LAN Network Prefix: Enter the LAN Network Prefix here. This can be based on ULA
(Unique Local Address).
x DNS server: IPv6 DNS address will be provided by your local ISP.
x 6to4 subnet ID: Specifies, in hexadecimal notation, a subnet ID other than 0
Prioritize traffic using QoS (Quality of Service)
Advanced > Setup > QoS
x Enable QoS: Enable or Disable the Quality of service through the router.
x Prioritize ACK: Enable or disable ACK prioritization.
x Prioritize ICMP: Enable or disable ICMP prioritization.
5. Select the traffic class you would like to configure for your QoS rule.
You may want to prioritize traffic for specific computers or devices on your network to
have higher priority. QoS involves prioritization of network traffic. QoS can be targeted
at a network interface, toward a given server or router's performance, or in terms of
specific applications.
1. Log into your router management page (see “Access your router management page”
on page 17).
6. Review the Inbound/Outbound Class Setting section.
2. Click on the Advanced tab.
© Copyright 2015 TRENDnet. All Rights Reserved.
28
TEW-818DRU
TRENDnet User’s Guide
x IP/MAC Address Filter: Select from the pull down menu the IP address or MAC you
would like to apply and enter the IP address of MAC address.
x Protocol Filter: Select the protocol you would like to apply on the QoS Rule.
x Port Filter: Select the port from the pull down menu you would like to assign on the
QoS rule and enter the port.
x Class Assigned: Select from the pull down menu the class you applied on the
previous section you would like to assign the QoS rule.
x Description: Enter the QoS description that best describes the rule.
Advanced wireless settings
x BW Max Inbound: Enter the maximum download speed of your ISP (Internet
Service Provider).
x Highest/High/Medium/Low/Lowest: Enter the download speeds you would like to
apply on each state of download speeds. This setting is similar to setting the priority
speeds of each class
7. Review the QoS Rule settings. Click Add Rule to add and save the rule to the QoS Rule
List
© Copyright 2015 TRENDnet. All Rights Reserved.
The advanced wireless features provide can provide you with additional options for
setting up your wireless network such as multiple SSID and WDS (Wireless Distribution
System) or wireless bridging.
Multiple SSID
Advanced > Wireless (2.4GHz or 5GHz) > Multiple SSID
The multiple SSID feature allows you to broadcast up to 2 additional SSIDs (or wireless
network names). When wireless devices are searching for available wireless networks to
connect to, the SSIDs (or wireless network names) will appear as separate and different
wireless networks. Since they appear as separate wireless networks, they are also
referred to as virtual APs (Access Points) since they appear as separate wireless access
points but are actually all being broadcasting and managed by a single wireless access
point. Each virtual AP can be configured each with a different SSID (or wireless network
name), security type and additional settings for wireless devices to connect. You can use
29
TEW-818DRU
TRENDnet User’s Guide
the multiple SSID feature to setup guest wireless accounts with a different security type
to keep your primary wireless network security information private. The diagram shows
an example of a client connecting to SSID 1 and another client connecting to SSID 2.
By default, your router functions in Access Point mode to allow wireless client devices to
connect and access your network resources and access the Internet using a single SSID.
The diagram shows an example of a client connecting to SSID 1 and another client
connecting to SSID 2.
To configure multiple SSID on your router:
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
3. Select the wireless band you would like to configure Wireless 2.4GHz or Wireless
5GHz and click on Multiple SSID.
© Copyright 2015 TRENDnet. All Rights Reserved.
4. Review the Multiple SSID settings, click Apply when finished.
x Enabled: Check the option to enable the Guest Network.
x Wireless Name (SSID): This acronym stands for Service Set Identifier and is the
name of your wireless network. It differentiates your wireless network from others
around you. It is recommended to use a different name from your primary wireless
network to a name that you can easily identify and differentiate from the primary.
You can reference your guests to access this network instead of the primary.
x Broadcast Network Name (SSID):
o Enabled allows wireless devices to search and discover your wireless network
name (also called SSID) broadcasted by your router.
o Disabled turns off the ability for wireless devices to find your network. It is still
possible for wireless devices to be configured to connect to your wireless
network. Disabling this setting will disable WPS functionality.
5. Under Security Policy, you can apply a different wireless security type and key to the
guest network. Please refer to page 15 to find out about different security types and
page 16 for wireless security configuration.
Note: You can repeat the steps to enable and configure additional SSIDs. You can
configure your wireless security settings for the additional SSIDs under Wireless
(2.4GHz or 5GHz)>Security. Under the Security Policy section, click the Wireless
Name (SSID) drop-down list to select the additional SSIDs to configure. Please refer
to page 15 to find out about different security types and page 16 for wireless
security configuration.
30
TEW-818DRU
TRENDnet User’s Guide
Wireless bridging using WDS (Wireless Distribution System)
Advanced > Wireless (2.4GHz or 5GHz) > WDS
Wireless bridging using WDS allows the device to create a wireless bridge with other
WDS supported wireless routers and access points configured in WDS mode to bridge
groups of network devices together wirelessly. Simultaneously, the router will also
function in access point mode allowing wireless client devices such as computers, game
consoles, mobile phones, etc. to connect in order to access network resources from
multiple groups of network devices as well as the Internet.
Note: You can create up to four WDS bridge connections on each wireless band
(2.4GHz and 5GHz). WDS (Wireless Distribution System) is not currently
standardized and may not connect to different model wireless routers or access
points, therefore, when using WDS, it is recommended to use the same model and
version for wireless bridging.
By default, your router functions in Access Point mode to allow wireless client devices to
connect and access your network resources and access the Internet.
In the diagram below, the blue color represents the WDS wireless bridged connections
between the routers. The green color represents access point mode connections
between wireless client devices and the routers.
1. Make sure different IP addresses are assigned to each WDS supported wireless
device used for bridging. (ex. 192.168.10.1,192.168.10.2, 192.168.10.3) to avoid
IP address conflict. See page 34 for changing the LAN IP address.
2. If you are using more than one WDS supported router, please make sure the LAN
DHCP server is enabled on only one and disabled on all others to avoid IP address
conflict. See page 35 for DHCP server options.
3. Configure the same wireless channel and use the same on all WDS supported
wireless devices. See page 20 for configuring basic wireless settings.
4. Configure the same wireless security and key on all WDS supported devices. See
page 15 for configuring wireless security settings.
To configure WDS bridging between TEW-818DRU routers:
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
3. Select wireless band you would like to configure, Wireless 2.4GHz or Wireless 5GHz
and click on WDS.
4. Next to Wireless Distribution System (WDS), in an empty field, enter the MAC
address of the other WDS supported wireless device you are bridging. (e.g.
00:11:22:AA:BB:CC). To save settings, click Apply.
Note: Before configuring WDS, please ensure the following first:
© Copyright 2015 TRENDnet. All Rights Reserved.
31
TEW-818DRU
TRENDnet User’s Guide
4. Review the Multiple SSID settings, click Apply when finished.
For additional routers, make sure to disable the DHCP server first on all additional
routers and configure the LAN IP address to be different on each router. You will
connect devices to the LAN ports 1-4 only on all additional routers and the WAN port is
not used. Then, repeat the steps for additional routers you are bridging.
Additional wireless settings
Advanced > Wireless (2.4GHz or 5GHz) > Advanced
These settings are advanced options that can be configured to change advanced
wireless broadcast specifications. It is recommended that these settings remain set to
their default values unless you are knowledgeable about the effects of changing these
values. Changing these settings incorrectly can degrade performance.
To configure multiple SSID on your router:
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
3. Select wireless band you would like to configure, Wireless 2.4GHz or Wireless 5GHz
and click on Multiple SSID.
© Copyright 2015 TRENDnet. All Rights Reserved.
x Beacon Interval: A beacon is a management frame used in wireless networks that
transmitted periodically to announce the presence and provide information about
the router’s wireless network. The interval is the amount time between each
beacon transmission.
Default Value: 100 milliseconds (range: 25-1000)
x DTIM: A DTIM is a countdown informing clients of the next window for listening to
broadcast and multicast messages. When the wireless router has buffered
broadcast or multicast messages for associated clients, it sends the next DTIM with
a DTIM Interval value. Wireless clients detect the beacons and awaken to receive
the broadcast and multicast messages. The default value is 1. Valid settings are
between 1 and 255.
x Fragment Threshold: Wireless frames can be divided into smaller units (fragments)
to improve performance in the presence of RF interference and at the limits of RF
coverage. Fragmentation will occur when frame size in bytes is greater than the
Fragmentation Threshold. This setting should remain at its default value of 2346
bytes. Setting the Fragmentation value too low may result in poor performance.
32
TEW-818DRU
TRENDnet User’s Guide
x RTS Threshold: The Request To Send (RTS) function is part of the networking
protocol. A wireless device that needs to send data will send a RTS before sending
the data in question. The destination wireless device will send a response called
Clear to Send (CTS). The RTS Threshold defines the smallest data packet size
allowed to initiate the RTS/CTS function.
Default Value: 2347 (range: 1-2347)
4. Review the Time settings. Click Apply to save settings.
x Short Preamble: Using a short (400ns) guard interval can increase throughput.
However, it can also increase error rate in some installations, due to increased
sensitivity to radio-frequency reflections. Select the option that works best for your
installation.
x Xpress™ Technology: A frame bursting technology used to improve wireless
performance. The feature will only work with other Xpress™ supported devices. It is
recommended to leave this feature On.
x MCS: Select the speed you would like your wireless network to operate.
Note: It is recommended to keep the default setting – Auto.
Set your router date and time
Advance > Administrator > Time
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
x Time Configuration: Displays the current device time and date information.
x Enable Daylight Saving: Check the option to configure the DST settings. Set the
annual range when daylight saving is activated.
x NTP Settings: Check the Enable NTP Server option to set your router date and time
to synchronize with an NTP (Network Time Protocol) server address (e.g.
pool.ntp.org). Enter the NTP server address next to Default NTP server, (e.g.
pool.ntp.org). Click the Time Zone drop-down list to select the appropriate zone
and you can optionally change your NTP Sync period.
Note: NTP servers are used for computers and other network devices to synchronize
time across an entire network.
3. Click on Administrator section and click Time.
x Manually set time – Set your router date and time manually in the Date and Time
Settings section.
Note: Time is specified in 24-hour format.
Create schedules
Advance > Administrator > Schedule
For additional security control, your router allows you to create schedules to specify a
time period when a feature on your router should be activated and deactivated. Before
you use the scheduling feature on your router, ensure that your router system time is
configured correctly.
© Copyright 2015 TRENDnet. All Rights Reserved.
33
TEW-818DRU
TRENDnet User’s Guide
Note: You can apply a predefined schedule to the following features:
Virtual Server
Access Control (Domain/URL Filters & IP/Protocol LAN Client Filters)
Special Applications
Gaming
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
Note: The schedule defined will define the time/day the feature will be activated.
Access Control
Advanced > Security > Access Control
You may want to block computers or devices on your network access to specific ports
(used or required by a specific application) to the Internet.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
3. Click on Administrator section and click Schedule.
3. Click on the Security section and click on Access Control.
3. Under Access Control, click the LAN Client Filter Function drop-down list and select
Enabled to activate the feature.
3. Review the Schedule settings. Click Apply to save settings.
4. Review the settings under LAN Client Filter Rules section. Click Apply to save settings.
x Rule Name: Enter a name for the schedule you would like to apply.
x Days: Check the days you would like the rule to be applied or select All Week to
enable the rule all week.
x Start/End Time: Select the start and end time you would like the schedule to follow.
© Copyright 2015 TRENDnet. All Rights Reserved.
x LAN IP Address Range: Enter the IP address or IP address range to apply the
protocol (e.g. 192.168.10.20-192.168.10.20 or 192.168.10.20-192.168.10.30).
34
TEW-818DRU
TRENDnet User’s Guide
Note: The filter will not be applied to IP addresses outside of the range specified.
x Protocol: Select the protocol type to filter. TCP, UDP.
x Destination Port Range: Enter the port number or range of port numbers to apply
in the firewall rule. (e.g. 80-80 or 20-21). For all ports, use the port range 1 - 65534.
x Schedule: Click the drop-down list to select the pre-defined schedule to apply. The
filter will only be active during the time period defined in the pre-defined schedule.
(See “Create Schedule” section on page 33).
Note: Before applying scheduling, please ensure your Time settings are configured
correct and you have defined a schedule. See page 32 to configure Time Settings
and see page 33 to create a schedule.
x Enabled: Checking the Enabled option activates on the LAN Client Filter rule.
Open a device on your network to the Internet
This router can provide access to devices on your local area network to the Internet
using the Virtual Server, Special Application, method (DMZ NOT recommended).
3. Click on the Firewall section and click on DMZ.
4. Select Enable in the DMZ Settings section.
5. Enter the IP address you assigned to the computer or network device to expose to the
Internet. Click Apply to save settings.
DMZ
Advanced > Firewall > DMZ
Virtual Server
You may want to expose a specific computer or device on your network to the Internet
to allow anyone to access it. Your router includes the DMZ (Demilitarized Zone) feature
that makes all the ports and services available on the WAN/Internet side of the router
and forwards them to a single IP address (computer or network device) on your
network. The DMZ feature is an easy way of allowing access from the Internet however,
it is a very insecure technology and will open local area network to greater threats from
Internet attacks.
Advanced > Firewall > Virtual Server Rules
It is strongly recommended to use Virtual Server (also called port forwarding, see
“Virtual Server” on page 35) to allow access to your computers or network devices from
the Internet.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
Virtual Server (also called port forwarding) allows you to define specific ports (used or
required by a specific application) and forward them to a single IP address (a computer
or device) on your network. Using this feature is more secure compared to using DMZ
(see “DMZ” on page 35) in which DMZ forwards all ports instead of only specific ports
used by an application. An example would be forwarding a port to an IP camera
(TRENDnet IP cameras default to HTTP TCP port 80 for remote access web requests) on
your network to be able to view it over the Internet. To open several ports please refer
to “Gaming” section on page 37.
Since most ISPs constantly change your home IP address, to be able to access the Virtual
Server port(s) from the Internet it is recommended to setup Dynamic DNS service
(outlined in Identify Your Network section page 50).
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
© Copyright 2015 TRENDnet. All Rights Reserved.
35
TEW-818DRU
TRENDnet User’s Guide
Note: The Public Port can be assigned a different port number than the Private Port
(also known as port redirection), however it is recommended to use the same port
number for both settings. Please refer to the device documentation to determine
which ports and protocols are required.
3. Click on the Firewall section and click on Virtual Server Rules.
x Enabled: Selecting Enabled turns on the virtual server and unchecking disabled the
rule.
Example: To forward TCP port 80 to your IP camera
1. Setup DynDNS service (see Identify Your Network section page 50).
2. Access TRENDnet IP Camera management page and forward Port 80 (see product
documentation)
3. Make sure to configure your network/IP camera to use a static IP address.
4. Select Enable in the Virtual Server Function section.
Note: You may need to reference your camera documentation on configuring a
static IP address.
4. Log into your router management page (see “Access your router management page”
on page 17).
5. Click on Advanced, and click on Virtual Server.
5. Review the virtual server settings. Click Apply to save settings.
x Protocol: Select the protocol required for your device. TCP or UDP.
Note: Please refer to the device documentation to determine which ports and
protocols are required. You should assign a static IP address to the device or use
DHCP reservation to ensure the IP address of the device does not change.
x Public Port: Enter the port number used to access the device from the Internet.
x LAN IP Address: Enter the IP address of the device to forward the port (e.g.
192.168.10.101).
x Schedule: Select the defined schedule you would like to have the rule to be applied
(see “Create Schedule” section on page 33).
© Copyright 2015 TRENDnet. All Rights Reserved.
6. Click Enabled to turn on this virtual server.
7. Next to Name, you can enter another name for the virtual server, otherwise, leave
the default name.
8. Next to LAN Server, enter the IP address assigned to the camera. (e.g.
192.168.10.101)
9. Next to Protocol, make sure TCP is selected in the drop-down list.
10. The Private Port and Public Port, make sure port number 80 is configured for both
settings.
11. To save the changes, click Add.
Special Applications
Advanced > Firewall > Special Applications
Special applications (also called port triggering) is typically used for online gaming
applications or communication applications that require a range of ports or several
ports to be dynamically opened on request to a device on your network. The router will
wait for a request on a specific port or range of ports (or trigger port/port range) from a
device on your network and once a request is detected by your router, the router will
forward a single port or multiple ports (or incoming port/port range) to the device on
your network. This feature is not typically used as most devices and routers currently
36
TEW-818DRU
TRENDnet User’s Guide
use UPnP (Universal Plug and Play) to automatically configure your router to allow
access for applications. See “Enable/disable UPnP on your router” on page 39.
Note: Please refer to the device documentation to determine if your device supports
UPnP first, before configuring this feature.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
x Match Port: Enter the ports or port range to be forwarded to the device. (e.g. 20002038 ,2200-2210).
x Trigger Protocol: Select the protocol requested by the device. TCP or UDP.
x Trigger Port: Enter the ports or port range requested by the device. (e.g. 554-554 or
6112-6112).
Note: Please refer to the device documentation to determine which ports and
protocols are required.
x Schedule: Select the defined schedule you would like to have the rule to be applied
(see “Create Schedule” section on page 33).
x Enabled: Selecting Enabled turns on the virtual server and selecting unchecking
disables the rule.
3. Click on the Firewall section and click on Special Applications.
Gaming
Advanced > Firewall > Gaming
4. Select Enable under Port Triggering Function.
Gaming allows you to define multiple ports (used or required by a specific application or
game) and forward them to a single IP address (a computer or device) on your network.
Using this feature is more secure compared to using DMZ (see “DMZ” on page 35) in
which DMZ forwards all ports instead of only specific ports used by an application. Since
most ISPs constantly change your home IP address, to be able to access the Virtual
Server port(s) from the Internet it is recommended to setup Dynamic DNS service (see
“Identify your network over the Internet” section on page 50).
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
5. Review the special application settings. Click Apply to save settings.
3. Click on the Firewall section and click on Special Applications.
x Match Protocol: Select the protocol to be forwarded to the device. TCP or UDP.
© Copyright 2015 TRENDnet. All Rights Reserved.
37
TEW-818DRU
TRENDnet User’s Guide
Enable/disable Application Layer Gateways (ALG)
Advanced > Firewall > ALG
You may want to configure your router to allow computers the use of specific high layer
applications or service sessions to pass through. Application Layer Gateways (ALG)
allows you to easily enable or disable these applications to pass through your router.
Note: It is recommended to leave these settings enabled.
1. Log into your router management page (see “Access your router management page”
on page 17).
4. Click on Enabled under Gaming Function section.
2. Click on the Advanced tab.
5. Review the virtual server settings. Click Apply to save settings.
3. Click on the Firewall section and click on Special Applications.
x LAN IP Address: Enter the IP address of the device to forward the port (e.g.
192.168.10.101).
x TCP Ports to Open: Enter the TCP port you would like to set.
x UDP Ports to Open: Enter the UDP port you would like to set.
4. Review the applications to enable or disable. Click Apply to save the changes.
Note: Please refer to the device documentation to determine which ports and
protocols are required. You should assign a static IP address to the device or use
DHCP reservation to ensure the IP address of the device does not change.
x Schedule: Select the defined schedule you would like to have the rule to be applied
(see “Create Schedule” section on page 33).
x Enabled: Selecting Enabled turns on the virtual server and selecting unchecking
disables the rule.
x Email Receiving (POP3): Allows POP3 protocol through your router.
© Copyright 2015 TRENDnet. All Rights Reserved.
38
TEW-818DRU
TRENDnet User’s Guide
Email Receiving (SMTP): Allows SMTP protocol through your router.
Streaming Video (RTP): Allows RTP video protocol through your router.
Streaming Media (RTSP): Allows STMP video protocol through your router.
Streaming Media (WMP/MMS): Allows WMP/MMS protocol through your router.
Streaming Media-VoIP (SIP): Allows SIP protocol through your router.
Streaming Media-VoIP (H.323): Allows H.323 protocol through your router.
File Transfer (FTP): Allows FTP protocol through your router.
File Transfer (TFTP): Allows TFTP protocol through your router.
Remote control (Telnet): Allows Telnet protocol through your router.
Instant messaging (MSN): Allows MSN instant messaging protocols through your
router.
x VPN Pass-Through: Allows VPN connections through your router.
Enable/disable UPnP on your router
4. Click the UPnP drop-down list and select Enabled to enable UPnP or Disabled to
disable UPnP. Click Apply to save settings.
Advanced > Advanced Network
UPnP (Universal Plug and Play) allows devices connected to a network to discover each
other and automatically open the connections or services for specific applications (e.g.
instant messenger, online gaming applications, etc.) UPnP is enabled on your router by
default to allow specific applications required by your computers or devices to allow
connections through your router as they are needed.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
Note: It is recommended to leave this setting enabled, otherwise, you may
encounter issues with applications that utilize UPnP in order allow the required
communication between your computers or devices and the Internet.
Using External USB Storage
Your router’s USB port can be used to share files through the network when a USB
storage device is connected on the back USB port. The router supports both FTP and
SAMBA (SMB) filing sharing protocols.
Samba Network File Server
3. Click on the Administrator section and click on Advanced Network.
Advanced > USB > SAMBA
Samba is a network protocol that allows you to access shared files through your
network. In order to share files, you will need to plug in a USB storage device on the USB
port on the back of the router. You can access these files under your network map or by
typing \\routerIPaddress on your browser’s address bar. Please follow the below steps
to configure the router’s Samba settings
© Copyright 2015 TRENDnet. All Rights Reserved.
39
TEW-818DRU
TRENDnet User’s Guide
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
x User Name: Enter the user name to be used to access your files.
x Password: Enter the password for the user name.
6. Review the User Account List section. Click Apply to save settings
3. Click on the USB section and click on Samba Server.
4. Review the setting on Samba Server Information section. Click Apply to save settings
User Name: Enter the user name to be used to access your files.
Password: Enter the password for the user name.
Permission: Select the permission you will grant to the user
Enabled: Click to activate user account.
FTP (File Transfer Protocol) Server
Advanced > USB > FTP
Server Status: Select enable or disable for the feature.
Server Name: Enter the name of your server.
Workgroup: Enter the work group of your server.
Description: Enter a description of the server.
5. Review the administrator settings required for your Samba server. Click Apply to save
settings. Administrator will have read and write access to files. To define user
accounts continue to the next step.
FTP (File Transfer Protocol) is used to access shared files through the Internet. In order
to share files, you will need to plug in a USB storage device on the USB port on the back
of the router. Signing up for a Dynamic DNS service (outlined in Identify Your Network
section pg.49) will provide identification of the router’s network from the Internet. You
can access your shared files by typing ex.ftp://router’sWANIPaddress or
ftp://myDDNSservice. Please follow the steps below to configure the router’s FTP
settings
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
© Copyright 2015 TRENDnet. All Rights Reserved.
40
TEW-818DRU
TRENDnet User’s Guide
3. Click on the USB section and click on FTP Server.
User Name: Enter the user name to be used to access your files.
Password: Enter the password for the user name.
Permission: Select the permission you will grant to the user
Enabled: Click to activate user account.
4. Review the setting on Samba Server Information section. Click Apply to save settings
Properly Eject USB device
Advanced > USB > Eject Device
It is recommended to properly eject your USB device to prevent any file corruption.
1. Log into your router management page (see “Access your router management page”
on page 17).
x Server Status: Select enable or disable for the feature.
x Language: Select your language.
2. Click on the Advanced tab.
5. Review the administrator settings required for your FTP server. Click Apply to save
settings
3. Click on the USB section and click on Eject Device.
x User Name: Enter the user name to be used to access your files.
x Password: Enter the password for the user name.
5. Review the User Account List section. Click Apply to save settings
4. Review the settings.
© Copyright 2015 TRENDnet. All Rights Reserved.
41
TEW-818DRU
TRENDnet User’s Guide
Print Share Utility Installation
Windows Installation
x Safely remove device: Click this button to eject your USB shared device
x Refresh: Click to refresh the connected USB device list.
1. For each computer that requires access to USB printer, insert the Utility CD-ROM into
your computer's CD-ROM Drive.
2. Click Install Utility
3. Follow the installation instructions and click Finish when prompted. Make sure to click
Launch TRENDnet USB Control Center Utility to run the utility.
© Copyright 2015 TRENDnet. All Rights Reserved.
42
TEW-818DRU
TRENDnet User’s Guide
4. Double click on the TRENDnet USB Control Center Utility icon
3. Double-click the file in the window.
5. The utility will automatically detect your router and USB printer.
MAC OS X Installation
4. You will be prompted to install the utility. Click Install to start the installation.
1. Insert the included CD-ROM into your computer’s CD-ROM drive.
5. You will be prompted for your password to allow the installation. Enter your
password and click OK.
2. Open the CD contents and locate the “TRENDnet USB Control Center Utility Installer”
(.dmg) file. Double-click the file.
© Copyright 2015 TRENDnet. All Rights Reserved.
43
TEW-818DRU
TRENDnet User’s Guide
MAC OS X
Upon completing the software installation, a desktop shortcut is automatically created.
Double-click the icon to start the utility. Closing the utility will exit the application.
Utility Main Window
6. Once the installation is completed. Click Restart to restart your computer.
In the utility window, you will see the model name and IP address of your print server
listed. When USB devices are connected, they will be listed under the model name and
IP address of the print server.
7. Run the TRENDnet USB Control Center Utility. The utility will automatically find your
router and USB printer.
Launching the Utility
Windows OS
Upon completing the software installation, a desktop shortcut is automatically created.
You double click the icon to start the utility or open the utility if it is already running.
Windows OS
MAC OS X Utility
If the utility is already running and you attempt to close the window, it will continue to
run in the background and you will find the icon in your notification area if the utility is
still running. To close and exit the utility and exit the application, you can right-click the
notification icon and select Exit or click System > Exit in the utility main window,
however, it is recommended to keep this utility running in the background.
Menu Items (Windows Only)
x System:- Clicking Exit will close the utility and exit the application.
x Tools
© Copyright 2015 TRENDnet. All Rights Reserved.
44
TEW-818DRU
TRENDnet User’s Guide
Windows OS
MAC OS X
Connect
o Configuration – Checking the option Automatically execute when logging on
Windows will automatically start the utility when you log on. Unchecking the
option will disable the utility from automatically starting when logging on.
o Auto-Connect Printer List – Provides a list of printers installed on your
computer. Select the printer you would like to assign to the Auto-Connect
printer list. If you would like to delete printers from this listing, select the
printer in the list and click Delete. Click Close to close the window.
x About
To connect your computer to a USB device, select the USB device in the list, then click
the Connect button to connect your computer to the USB device.
Note: The utility will only allow one computer to connect to one USB device at any given
time, therefore, a computer must disconnect from the USB device first before another
computer can connect to it.
Windows OS
MAC OS X
To verify if you are connected to the USB device, a message will appear next to the USB
device displaying a message that the USB device is “Manually connected by ”.
Windows OS
MAC OS X
o About – Displays the software/driver version and support contact information.
Configure Server
Select the print server you would like to configure in the utility window.
Windows OS
MAC OS X
Disconnect
To disconnect your computer from a USB device, select the USB device in the list, then
click the Disconnect button to disconnect your computer to the USB storage device or
printer.
Note: The utility will only allow one computer to connect to one USB device at any given
time, therefore, a computer must disconnect from the USB device first before another
computer can connect to it.
1. Clicking the Configure Server button will open the router’s management page in your
web browser.
© Copyright 2015 TRENDnet. All Rights Reserved.
45
TEW-818DRU
TRENDnet User’s Guide
Sending a Request to Connect
You can send a request to connect to the computer that is currently connected to the
USB device you would like to establish connection too.
Windows OS
MAC OS X
To verify if you disconnected from the USB device, the status message next to the
message will not show any status message.
Windows OS
To send t a request to connect to a USB device, click the Request to Connect button.
The remote computer will receive the request message below.
Windows OS
MAC OS X
If another computer is currently connected to the USB device you are trying to connect
your computer to, you will not be able to connect to it. To verify if another computer is
connected to the device, a message will appear next to the USB device displaying a
message that the USB device is “Manually connected by ”.
Windows OS
x Accept: Clicking this option will disconnect your computer from the device and
allow the requesting computer to connect to the USB device.
x Reject: Clicking this option will disregard the request and your computer will not
be able to connect to the USB
MAC OS X
If a USB device is currently being used by another computer, click the Request to
Connect button to send a request to the computer that is currently connected to the
USB device. The computer that is currently connected to USB device will be prompted to
“Accept” or “Reject” the your connection request.
MAC OS X
To send t a request to connect to a USB device, click the Request to Connect button.
Windows OS
MAC OS X
The local computer sending the request will show the status message below.
© Copyright 2015 TRENDnet. All Rights Reserved.
46
TEW-818DRU
TRENDnet User’s Guide
The remote computer will receive the request message below.
If the remote computer rejects the request, the local computer will display the message
below. Click OK to close the message.
Connect to a Printer
x Accept: Clicking this option will disconnect your computer from the device and
allow the requesting computer to connect to the device.
Note: This function applies to stand-alone USB printers or USB multi-function
printers. It is required that the printer drivers are installed before your
computer is able to print. Please ensure the printer drivers are installed. If the
printer drivers are not installed, please refer to your printer manufacturer
website or documentation on where to download and how to install the printer
drivers. Before installing the printer drivers, connect your computer to the
printer using the USB utility first. Some printers may require that the printer is
directly connected to the computer in order to complete the driver installation.
Once the printer drivers are installed properly on your computer,
1. Select the printer listed in the utility.
2. Click Connect to connect your computer to the printer.
3. Once your computer is connected, you can send print jobs to the printer.
If the remote computer accepts the request, the local computer will display the message
below. Click Close to close the message.
x Reject: Clicking this option will disregard the request.
© Copyright 2015 TRENDnet. All Rights Reserved.
4. After you have finished printing, click Disconnect, to make the printer available to
other computers on your network that use the printer, or, you can use the AutoConnect Printer Feature.
47
TEW-818DRU
TRENDnet User’s Guide
Auto-Connect Printer
When a USB printer is connected and selected in the main window, clicking this option
allows you to enable/disable the auto connect feature to a selected printer in the AutoConnect printer list. When your computer attempts to print, the Auto-Connect feature
will automatically connect your computer to the set Auto-Connect printer assigned in
the utility. Once the print job from your computer is completed, it will automatically
disconnect to make the printer available to other computers on your network.
Note: It is recommended to enable this feature on all computers that will need to
connect to the USB printer. Enabling the Auto-Connect Printer feature will avoid the
complexity of having to manually connect and disconnect from the printer for each
computer when multiple computers are sending print jobs to the USB printer.
Connect to a Scanner
Note: This function applies to stand-alone USB scanners or USB scanners
included with multi-function printers. It is required that the scanner drivers are
installed before your computer is able to scan. Please ensure the scanner
drivers are installed. If the scanner drivers are not installed, please refer to your
printer manufacturer website or documentation on where to download and
how to install the scanner drivers. Before installing the scanner drivers, connect
your computer to the printer using the USB utility first. Some scanners may
require that the scanner is directly connected to the computer in order to
complete the driver installation.
1. Select the scanner or multi-function printer with scanning capability listed in the
utility.
1. Click Auto-Connect Printer.
2. Select the assigned printer to use as the auto connect printer by checking the box.
2. Click Connect to connect your computer to the scanner.
3. Once your computer is connected, you can receive scanned files from the scanner.
3. When you are finished, click Apply.
4. After you have finished printing, click Disconnect, to make the scanner available to
other computers on your network that use the scanner.
© Copyright 2015 TRENDnet. All Rights Reserved.
48
TEW-818DRU
TRENDnet User’s Guide
Router Maintenance & Monitoring
Change your router login password
Advanced > Administrator > Management
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
access the router management page use the predefined settings on the side or
bottom labels.
Change your device name
Advanced > Administrator > Management
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
3. Click on the Administrator section and click on Management.
3. Click on the Administrator section and click on Management.
4. Under the Administrator Settings section, in the Password field, enter the new
password. Click Apply to save settings.
4. Under the Device Name Settings section, in the Device Name field, enter the new
device name to display on your network to identify the router. Click Apply to save
settings.
x Idle Timeout: Enter the idle timeout in seconds before automatically logging you
out of the router management page.
Note: If you change the router login password, you will need to access the router
management page using the User Name “admin” and the new password instead of
the default password “admin”. If you reset the device to defaults, you will need to
© Copyright 2015 TRENDnet. All Rights Reserved.
49
TEW-818DRU
TRENDnet User’s Guide
Change your device URL
Advanced > Administrator > Management
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
management area. Dynamic DNS services allow your router to confirm its location to the
given Dynamic DNS service, thereby providing the Dynamic DNS service with the ability
to provide a virtual fixed IP address for your network. This means that even though your
ISP is always changing your IP address, the Dynamic DNS service will be able to identify
your network using a fixed address—one that can be used to view home IP Camera and
other devices on your local area network.
Note: First, you will need to sign up for one of the DDNS service providers listed in
the Server Address drop-down list.
1. Log into your router management page (see “Access your router management page”
on page 17).
3. Click on the Administrator section and click on Management.
2. Click on the Advanced tab.
3. Click on the Administrator section and click on Management.
3. Under the Device URL Settings section, in the Device URL field, enter the new device
URL used to log into the router management page.
Note: Even if the LAN IP address of the router is changed, the device URL will still
allow to use the name as reference to log into the router management page.
4. Review the DDNS Settings section. Click Apply to save settings.
4. To save changes, click Apply.
Identify your network on the Internet
Advanced > Administrator > Management
Since most ISPs constantly change your home IP address, providing access to devices on
your home or small office Local Area Network (such as IP Cameras) from the Internet
requires setting up a Dynamic DNS service and entering the parameters into this
© Copyright 2015 TRENDnet. All Rights Reserved.
x Dynamic DNS Provider: Click the drop-down list Select your DDNS service.
50
TEW-818DRU
TRENDnet User’s Guide
x Host Name: Personal URL provided to you by your Dynamic DNS service provider
(e.g. www.trendnet.dyndns.biz)
x User Name: The user name needed to log in to your Dynamic DNS service account
x Password: This is the password to gain access to Dynamic DNS service (NOT your
router or wireless network password) for which you have signed up to.
Note: If you would like to discard the changes, click Cancel before you click Save.
x Remote Control: Select enable or disable for the feature.
x Port: Enter the port to assign remote access to the router. It is recommended to
leave this setting as 8080.
Note: If you have configured port 8080 for another configuration section such as
virtual server or special application, please change the port to use.
(Recommended port range 1024-65534)
Allow remote access to your router management page
Reset your router to factory defaults
Advanced > Administrator > Management
Advance > Administrator > Settings Management
You may want to make changes to your router from a remote location such at your
office or another location while away from your home.
1. Log into your router management page (see “Access your router management page”
on page 17).
You may want to reset your router to factory defaults if you are encountering difficulties
with your router and have attempted all other troubleshooting. Before you reset your
router to defaults, if possible, you should backup your router configuration first, see
“Backup and restore your router configuration settings” on page 52.
2. Click on the Advanced tab.
There are two methods that can be used to reset your router to factory defaults.
x Reset Button – Located on the side panel of your router, see “Product Hardware
Features” on page 5. Use this method if you are encountering difficulties with
accessing your router management page.
OR
x Router Management Page
3. Click on the Administrator section and click on Management.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
4. Review the setting on the Remote Management section. Click Apply to save settings
3. Click on the Administrator section and click on Settings Management.
© Copyright 2015 TRENDnet. All Rights Reserved.
51
TEW-818DRU
TRENDnet User’s Guide
Backup and restore your router configuration settings
Advanced > Administrator > Settings Management
You may have added many customized settings to your router and in the case that you
need to reset your router to default, all your customized settings would be lost and
would require you to manually reconfigure all of your router settings instead of simply
restoring from a backed up router configuration file.
To backup your router configuration:
4. Under Load Factory Default, click Load Default. When prompted to confirm this
action, click OK.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
Router Default Settings
3. Click on the Administrator section and click on Settings Management.
Administrator User Name
admin
Administrator Password
Please refer sticker or device label
Router IP Address
192.168.10.1
Router Subnet Mask
255.255.255.0
DHCP Server IP Range
192.168.10.101-192.168.199
Wireless 2.4GHz
Enabled
Wireless 2.4GHz Encryption
Please refer sticker or device label
Wireless 5Ghz
Enabled
Wireless 5GHz Encryption
Please refer sticker or device label
4. Under Export Settings section, click Export.
5. Depending on your web browser settings, you may be prompted to save a file (specify
the location) or the file may be downloaded automatically to the web browser
settings default download folder. (Default Filename: .cfg)
© Copyright 2015 TRENDnet. All Rights Reserved.
52
TEW-818DRU
TRENDnet User’s Guide
To restore your router configuration:
Upgrade your router firmware
1. Log into your router management page (see “Access your router management page”
on page 17).
Advanced > Administrator > Upload Firmware
2. Click on the Advanced tab.
3. Click on the Administrator section and click on Settings Management.
TRENDnet may periodically release firmware upgrades that may add features or fix
problems associated with your TRENDnet router model and version. To check if there is
a firmware upgrade available for your device, please check your TRENDnet model and
version using the link. http://www.trendnet.com/downloads/
In addition, it is also important to verify if the latest firmware version is newer than the
one your router is currently running. To identify the firmware that is currently loaded on
your router, log in to the router, click on the Administrator section and then on the
Status. The firmware used by the router is listed at the top of this page. If there is a
newer version available, also review the release notes to check if there were any new
features you may want or if any problems were fixed that you may have been
experiencing.
1. If a firmware upgrade is available, download the firmware to your computer.
2. Unzip the file to a folder on your computer.
4. Under Import Settings, next to Settings file location, depending on your web
browser, click on Browse or Choose File.
5. A separate file navigation window should open.
6. Select the router configuration file to restore and click Import. (Default Filename:
.cfg). If prompted, click Yes or OK. Wait for the router to restore settings.
Please note the following:
x Do not interrupt the firmware upgrade process. Do not turn off the device or press
the Reset button during the upgrade.
x If you are upgrade the firmware using a laptop computer, ensure that the laptop is
connected to a power source or ensure that the battery is fully charged.
x Disable sleep mode on your computer as this may interrupt the firmware upgrade
process.
x Do not upgrade the firmware using a wireless connection, only using a wired
network connection.
x Any interruptions during the firmware upgrade process may permanently damage
your router.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
© Copyright 2015 TRENDnet. All Rights Reserved.
53
TEW-818DRU
TRENDnet User’s Guide
3. Click on the Administrator section and click on Upload Firmware.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
3. Depending on your web browser, in the Upload Firmware section, click Browse or
Choose File.
3. Click on the Administrator section and click on Settings Management.
4. Navigate to the folder on your computer where the unzipped firmware file (.bin) is
located and select it.
5. Click Apply. If prompted, click Yes or OK.
3. Under System Reboot section, click Reboot.
Reboot your router
Administrator > Settings Management
You may want to restart your router if you are encountering difficulties with your router
and have attempted all other troubleshooting.
There are two methods that can be used to restart your router.
x Turn the router off for 10 seconds using the router On/Off switch (EU version
only) located on the rear panel of your router or disconnecting the power port,
sees “Product Hardware Features” on page 5.
Use this method if you are encountering difficulties with accessing your router
management page. This is also known as a hard reboot or power cycle.
OR
x Router Management Page – This is also known as a soft reboot or restart.
© Copyright 2015 TRENDnet. All Rights Reserved.
Allow/deny ping requests to your router from the Internet
Advanced > Advanced Network
To provide additional security, you may want to disable your router from responding to
ping or ICMP (Internet Control Message Protocol) requests from the Internet. A ping is
network communication test to check if a device with IP address is alive or exists on the
network. By disabling this feature, you can conceal your router’s IP address and
existence on the Internet by denying responses to ping requests from the Internet. You
can additionally use this feature as a tool for troubleshooting purposes.
54
TEW-818DRU
TRENDnet User’s Guide
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
2. Click on the Advanced tab.
3. Click on the Administrator section and click on Router Status.
3. Click on the Administrator section and click on Settings Management.
4. Click the WAN Ping Respond drop-down list and select Enabled to allow ping requests
from your router to the Internet. Click Apply to save settings.
System Info
5. To save changes, click Apply.
Note: If you would like to discard the changes, click Cancel before you click Save.
Check the router system information
Advanced > Administrator > Router Status
x Firmware Version: The current firmware version your router is running.
x System Time: The current time set on your router.
x Router Up Time: The duration your router has been running continuously
without a restart/power cycle (hard or soft reboot) or reset.
You may want to check the system information of your router such as WAN (Internet)
connectivity, wireless and wired network settings, router MAC address, and firmware
version.
1. Log into your router management page (see “Access your router management page”
on page 17).
© Copyright 2015 TRENDnet. All Rights Reserved.
55
TEW-818DRU
TRENDnet User’s Guide
Internet Configurations
x IP Address: Displays your router’s current IP address.
x Subnet Mask: Displays your router’s current subnet mask.
2.4GHz Wireless LAN
x Connected Type: The WAN connection type applied on your router.
x IP Address: The current IP address assigned to your router WAN port or interface
configuration.
x Subnet Mask: The current subnet mask assigned to your router WAN port or
interface configuration.
x Default Gateway: The current gateway assigned to your router WAN port or
interface configuration.
x DNS (Domain Name System): The current DNS address(es) assigned to your router
port or interface configuration.
x Renew (DHCP WAN Type): Click this option to renew your WAN IP address.
x Release (DHCP WAN Type): Click this option to release the WAN IP address of your
router.
x Connect (PPPoE WAN Type): Click this option to connect to your DSL ISP
x Disconnect (PPPoE WAN Type): Click this option to disconnect from your DSL ISP.
x MAC Address: The MAC address of your router’s wireless LAN or interface
configuration.
x Channel: Displays the current wireless channel your router is operating.
x Network Name (SSID)/ Security Mode: Displays the current wireless network name
assigned to your router and the wireless security applied to the SSID
5GHz Wireless LAN
LAN Information
x MAC Address: The current MAC address of your router’s wireless or interface
configuration.
© Copyright 2015 TRENDnet. All Rights Reserved.
56
TEW-818DRU
TRENDnet User’s Guide
x MAC Address: The MAC address of your router’s wireless LAN or interface
configuration.
x Channel: Displays the current wireless channel your router is operating.
x Network Name (SSID)/ Security Mode: Displays the current wireless network name
assigned to your router and the wireless security applied to the SSID
IPv6 Status
Advanced > Administrator > IPv6 Status
You can view the current IPv6 status on your router.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
Connected Type: The type of IPv6 being used on your router.
Network Type: Your IPv6 network type.
Network Prefix: IPv6 prefix used
IPv6 Default Gateway: IPv6 default gateway
IPv6 DNS Server: IPv6 DNS server
3. Click on the Administrator section and click on IPv6 Status.
View your router log
Administrator > System Log
Your router log can be used to obtain activity information on the functionality of your
router or for troubleshooting purposes.
1. Log into your router management page (see “Access your router management page”
on page 17).
2. Click on the Advanced tab.
3. Click on the Administrator section and click on System Log.
© Copyright 2015 TRENDnet. All Rights Reserved.
57
TRENDnet User’s Guide
TEW-818DRU
4. Select Enable System Log and click Apply to save settings.
x Refresh: Click to refresh screen.
x Clear: Click to clear the screen.
© Copyright 2015 TRENDnet. All Rights Reserved.
58
TEW-811DRU
TRENDnet User’s Guide
Router Management Page Structure
BASIC
Network Status
Internet Connection Setup Wizard
Wireless Security Setup Wizard
DDNS Settings
Remote Management
Multiple SSID
Upload Firmware
WDS
Settings Management
Advanced
WPS
Wireless
Export Settings
Import Settings
2.4 GHz Wireless Network
Load Factory Default
Security
Reboot
5GHz Wireless Network
Security
Guest Network
Schedule
Advanced
Router Status
WPS
IPv6 Status
System Log
5GHz Guest Network
Advance Network
Security
MAC Filter
Management
UPnP
WAN Ping
Access Control
DMZ
Virtual Server Rules
Special Applications
LAN Setting
Gaming
DHCP Server
ALG
DHCP Reservations
Access Control
WAN Setting
Clone MAC
Routing
IPv6 Setting
Password
QoS
Device Name
Wizard
Device URL
© Copyright 2015 TRENDnet. All Rights Reserved.
Firewall
Setup
ADVANCE
Administrator
Security
Parental Control
WDS
Security
IP Filter
Multiple SSID
Time
2.4 GHz Guest Network
Web URL Filter
Wireless 5GHz
Wireless 2.4GHz
USB
Samba Server
FTP Server
Eject Device
59
Limited Warranty
TRENDnet User’s Guide
log, ping test tool
Technical Specifications
Supported
Hardware
Standards
Internet Protocol
Wired: IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-TX),
IEEE 802.3ab (1000Base-T)
Web Browser
LED Indicator
Wireless: IEEE 802.11ac (draft 2.0), IEEE 802.11n, IEEE
802.11g, IEEE 802.11b, 802.11a
IPv4 and IPv6
Power Adapter
Internet Explorer 6.0 or above, Firefox 2.0 or above,
Chrome, Opera, Safari
Power/WPS, LAN 1-4, WAN, 2.4 GHz Wireless, 5 GHz
Wireless, USB
Input: 100 ~ 240 V, 50~60 Hz, 0.8 A
Output: 12 V DC, 2 A external power adapter
LAN
4 x 10/100/1000 Mbps Auto-MDIX
Power Consumption
WAN
1 x 10/100/1000 Mbps Auto-MDIX
Dimension (L x W x H)
48 x 155 x 180 mm (1.8 x 6.1 x 7.1 in)
1 x USB 3.0 Type-A (Storage / Printing)
Weight
395 g (14 oz)
USB
1 x USB 2.0 Type-A (Storage / Printing)
WPS Button
Wi-Fi Protected Setup (WPS) connects with other WPS
compliant devices
Reset Button
Reset unit back to factory default (press and hold for 10
seconds)
Network
Protocols / Features
IGMP v1/2/3 proxy and snooping , Static and dynamic
routing, UPnP, DHCP, server, Dynamic DNS (No-IP.com
and DynDNS.com), NTP, IPsec / PPTP / L2TP VPN pass
through, IPv6
Quality of Service
WMM and WAN (Configurable Upload / Download)
Control Center Utility
Windows: 8 (32/64-bit), 7 (32/64-bit), Vista (32/64-bit),
XP (32/64-bit)
OS Support
Internet
Connection Type
Firewall
Management
/ Monitoring
Temperature
Storage: -20q~ 60qC (-4qF~140 qF)
Max. 90% (non-condensing)
Certifications
CE, FCC
Wireless
2.4 GHz: 2.412~2.462 (FCC) and 2.412~2.472 (ETSI)
Frequency
Antenna
Modulation
IPv6, Dynamic IP, Static (fixed) IP, PPPoE, PPTP, L2TP
5 GHz: 5.18 ~ 5.24 / 5.745~5.825 GHz (FCC) and 5.18 ~
5.240 (ETSI)
2.4 GHz: 6.0dBi Max Peak Gain(Front Top), 5.5dBi Max
Peak Gain (Front Bottom), 2.5dBi Max Peak Gain (Top)
5 GHz: 6.0dBi Max Peak Gain (Front Top), 6.0dBi Max
Peak Gain (Front Bottom), 4.8dBi Max Peak Gain (Top)
CCK, DQPSK, DBPSK, OFDM, BPSK, QPSK, 16/64/256QAM
802.11a: up to 54 Mbps
NAT, SPI, DMZ host, virtual servers, MAC / IP filters and
URL filter
802.11b: up to 11 Mbps
Data Rate
© Copyright 2015 TRENDnet. All Rights Reserved.
Operation: 0q~ 40qC (32qF~ 104qF)
Humidity
Mac OS X: 10.4 / 10.5/ 10.6/ 10.7/ 10.8
Local / remote configuration, upgrade firmware, backup
/ restore configuration via web browser, internal system
22 watts (max.)
802.11g: up to 54 Mbps
802.11n: up to 600 Mbps 2.4GHz (TurboQAM), up to 450
Mbps 5GHz
60
TRENDnet User’s Guide
Limited Warranty
802.11ac: up to 1.3 Gbps
Security
WPA/WPA2-PSK, WPA/WPA2-RADIUS
Guest network
1 per wireless band
Access Control
MAC Address Filter (Up to 24 entries)
802.11a: 22 dBm (max.) FCC, 18 dBm (max.) CE @ HT40
802.11b: 19 dBm (max.) @ CCK
802.11g: 18 dBm (max.) @ HT40
Output Power
802.11n (2.4GHz): 18 dBm (max.) @ HT40
802.11n (5GHz): 22 dBm (max.) FCC, 18 dBm (max.) CE @
HT40
802.11ac: 23 dBm (max.) FCC, 19 dBm (max.) CE @ HT80
802.11a: -68 dBm (typical) @ 54 Mbps
802.11b: -84 dBm (typical) @ 11 Mpbs
Receiving Sensitivity
802.11g: -72 dBm (typical) @ 54 Mbps
802.11n: -68 dBm (typical) @ 600 Mbps for 2.4 GHz,
@450 Mbps for 5 GHz
802.11ac: -55 dBm (typical) @ 1.3 Gbps
2.4 GHz: 1~11 (FCC), 1~13 (ETSI)
Channels
5 GHz: 36, 40, 44, 48, 149, 153, 157, 161, 165 (FCC) 36,
40, 44, 48 (ETSI)
*Maximum wireless signal rates are referenced from IEEE 802.11 theoretical
specifications. Actual data throughput and coverage will vary depending on
interference, network traffic, building materials and other conditions. TurboQAM
speeds requires clients with TurboQAM support.
** Printer Control Center utility installation required for each computer in order to
access the printer
© Copyright 2015 TRENDnet. All Rights Reserved.
61
TRENDnet User’s Guide
Troubleshooting
Q: I typed http://192.168.10.1 in my Internet Browser Address Bar, but an error
message says “The page cannot be displayed.” How can I access the router
management page?
Answer:
1. Check your hardware settings again. See “Router Installation” on page 8.
2. Make sure the LAN and WLAN lights are lit.
3. Make sure your network adapter TCP/IP settings are set to Obtain an IP address
automatically or DHCP (see the steps below).
4. Make sure your computer is connected to one of the router’s LAN ports
5. Press on the factory reset button for 15 seconds, the release.
Windows 7
a. Go into the Control Panel, click Network and Sharing Center.
b. Click Change Adapter Settings, right-click the Local Area Connection icon.
c. Then click Properties and click Internet Protocol Version 4 (TCP/IPv4).
d. Then click Obtain an IP address automatically and click OK.
Windows Vista
a. Go into the Control Panel, click Network and Internet.
b. Click Manage Network Connections, right-click the Local Area Connection
icon and click Properties.
c. Click Internet Protocol Version (TCP/IPv4) and then click Properties.
d. Then click Obtain an IP address automatically and click OK.
Windows XP/2000
a. Go into the Control Panel, double-click the Network Connections icon
b. Right-click the Local Area Connection icon and the click Properties.
c. Click Internet Protocol (TCP/IP) and click Properties.
d. Then click Obtain an IP address automatically and click OK.
Note: If you are experiencing difficulties, please contact your computer or operating
system manufacturer for assistance.
© Copyright 2015 TRENDnet. All Rights Reserved.
Limited Warranty
Q: I am not sure what type of Internet Account Type I have for my Cable/DSL
connection. How do I find out?
Answer:
Contact your Internet Service Provider (ISP) for the correct information.
Q: The Wizard does not appear when I access the router. What should I do?
Answer:
1. Click on Wizard on the left hand side.
2. Near the top of the browser, “Pop-up blocked” message may appear. Right click on
the message and select Always Allow Pop-ups from This Site.
3. Disable your browser's pop up blocker.
Q: I went through the Wizard, but I cannot get onto the Internet. What should I do?
Answer:
1. Verify that you can get onto the Internet with a direct connection into your modem
(meaning plug your computer directly to the modem and verify that your single
computer (without the help of the router) can access the Internet).
2. Power cycle your modem and router. Unplug the power to the modem and router.
Wait 30 seconds, and then reconnect the power to the modem. Wait for the modem to
fully boot up, and then reconnect the power to the router.
3. Contact your ISP and verify all the information that you have in regards to your
Internet connection settings is correct.
Q: I cannot connect wirelessly to the router. What should I do?
Answer:
1. Double check that the WLAN light on the router is lit.
2. Power cycle the router. Unplug the power to the router. Wait 15 seconds, then plug
the power back in to the router.
3. Contact the manufacturer of your wireless network adapter and make sure the
wireless network adapter is configured with the proper SSID. The preset SSID is
TRENDnet(model_number).
4. To verify whether or not wireless is enabled, login to the router management page,
click on Wireless.
5. Please see “Steps to improve wireless connectivity” on page 21 if you continue to
have wireless connectivity problems.
62
Limited Warranty
TRENDnet User’s Guide
Appendix
Note: If you are experiencing difficulties, please contact your computer or operating
system manufacturer for assistance.
How to find your IP address?
Note: Please note that although the following procedures provided to follow for your
operating system on configuring your network settings can be used as general
guidelines, however, it is strongly recommended that you consult your computer or
operating system manufacturer directly for assistance on the proper procedure for
configuring network settings.
Command Prompt Method
How to configure your network settings to obtain an IP address automatically or use
DHCP?
Note: Please note that although the following procedures provided to follow for your
operating system on configuring your network settings can be used as general
guidelines, however, it is strongly recommended that you consult your computer or
operating system manufacturer directly for assistance on the proper procedure for
configuring network settings.
Windows 2000/XP/Vista/7
1. On your keyboard, press Windows Logo+R keys simultaneously to bring up the Run
dialog box.
2. In the dialog box, type cmd to bring up the command prompt.
Windows 7
a. Go into the Control Panel, click Network and Sharing Center.
b. Click Change Adapter Settings, right-click the Local Area Connection icon.
3. In the command prompt, type ipconfig /all to display your IP address settings.
c. Then click Properties and click Internet Protocol Version 4 (TCP/IPv4).
MAC OS X
d. Then click Obtain an IP address automatically and click OK.
1. Navigate to your Applications folder and open Utilities.
2. Double-click on Terminal to launch the command prompt.
3. In the command prompt, type ipconfig getifaddr  to display the wired
or wireless IP address settings.
Note: en0 is typically the wired Ethernet and en1 is typically the wireless Airport
interface.
Graphical Method
MAC OS 10.6/10.5
1. From the Apple menu, select System Preferences.
2. In System Preferences, from the View menu, select Network.
3. In the Network preference window, click a network port (e.g., Ethernet, AirPort,
modem). If you are connected, you'll see your IP address settings under "Status:"
MAC OS 10.4
1. From the Apple menu, select Location, and then Network Preferences.
2. In the Network Preference window, next to "Show:", select Network Status. You'll see
your network status and your IP address settings displayed.
© Copyright 2015 TRENDnet. All Rights Reserved.
Windows Vista
a. Go into the Control Panel, click Network and Internet.
b. Click Manage Network Connections, right-click the Local Area Connection
icon and click Properties.
c. Click Internet Protocol Version (TCP/IPv4) and then click Properties.
d. Then click Obtain an IP address automatically and click OK.
Windows XP/2000
a. Go into the Control Panel, double-click the Network Connections icon
b. Right-click the Local Area Connection icon and the click Properties.
c. Click Internet Protocol (TCP/IP) and click Properties.
d. Then click Obtain an IP address automatically and click OK.
MAC OS 10.4/10.5/10.6
a. From the Apple, drop-down list, select System Preferences.
b. Click the Network icon.
c. From the Location drop-down list, select Automatic.
d. Select and view your Ethernet connection.
In MAC OS 10.4, from the Show drop-down list, select Built-in Ethernet and
select the TCP/IP tab.
In MAC OS 10.5/10.6, in the left column, select Ethernet.
e. Configure TCP/IP to use DHCP.
63
Limited Warranty
TRENDnet User’s Guide
In MAC 10.4, from the Configure IPv4, drop-down list, select Using DHCP and
click the Apply Now button.
In MAC 10.5, from the Configure drop-down list, select Using DHCP and click
the Apply button.
In MAC 10.6, from the Configure drop-down list, select Using DHCP and click
the Apply button.
f. Restart your computer.
How to connect to a wireless network using the built-in Windows utility?
Note: Please note that although the following procedures provided to follow for your
operating system on configuring your network settings can be used as general
guidelines, however, it is strongly recommended that you consult your computer or
operating system manufacturer directly for assistance on the proper procedure for
connecting to a wireless network using the built-in utility.
Windows 7
Note: If you are experiencing difficulties, please contact your computer or operating
system manufacturer for assistance.
How to find your MAC address?
In Windows 2000/XP/Vista/7,
Your computer MAC addresses are also displayed in this window, however, you can type
getmac –v to display the MAC addresses only.
In MAC OS 10.4,
1. Apple Menu > System Preferences > Network
2. From the Show menu, select Built-in Ethernet.
3. On the Ethernet tab, the Ethernet ID is your MAC Address.
1. Open Connect to a Network by clicking the network icon (
area.
or
) in the notification
2. In the list of available wireless networks, click the wireless network you would like to
connect to, then click Connect.
4. You may be prompted to enter a security key in order to connect to the network.
5. Enter in the security key corresponding to the wireless network, and click OK.
Windows Vista
1. Open Connect to a Network by clicking the Start Button.
To.
and then click Connect
2. In the Show list, click Wireless.
3. In the list of available wireless networks, click the wireless network you would like to
connect to, then click Connect.
In MAC OS 10.5/10.6,
4. You may be prompted to enter a security key in order to connect to the network.
1. Apple Menu > System Preferences > Network
5. Enter in the security key corresponding to the wireless network, and click OK.
2. Select Ethernet from the list on the left.
3. Click the Advanced button.
Windows XP
3. On the Ethernet tab, the Ethernet ID is your MAC Address.
1. Right-click the network icon in the notification area, then click View Available
Wireless Networks.
2. In Connect to a Network, under Available Networks, click the wireless network you
would like to connect to.
3. You may be prompted to enter a security key in order to connect to the network.
4. Enter in the security key corresponding to the wireless network, and click Connect.
© Copyright 2015 TRENDnet. All Rights Reserved.
64
Limited Warranty
TRENDnet User’s Guide
Federal Communication Commission Interference Statement
Europe – EU Declaration of Conformity
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
TRENDnet hereby declare that the product is in compliance with the essential requirements
and other relevant provisions under our sole responsibility.
x Reorient or relocate the receiving antenna.
x Increase the separation between the equipment and receiver.
x Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
x Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Safety
EN60950-1 : 2006 + A11 : 2009 + A1: 2010 + A12: 2011
EMC
EN 55022: 2010 + AC: 2011 Class B
EN 55024: 2010
EN 301 489-1 V1.9.2: 09-2011
EN 301 489-17 V2.2.1: 09-2012
Radio Spectrum & Health
EN 300 328 V1.8.1 : (2012-06)
EN 301 893 V1.7.1 : (2012-06)
EN 62311 : 2008
Energy Efficiency
Regulation (EC) No. 1275/2008, Regulation, No. 278/2009, No. 801/2013
This product is herewith confirmed to comply with the Directives.
Directives
Low Voltage Directive 2006/95/EC
IMPORTANT NOTE:
EMC Directive 2004/108/EC
Radiation Exposure Statement:
R&TTE Directive 1999/5/EC
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm
20c
20
0c
0 m between the radiator & your body.
Ecodesign Directive 2009/125/EC
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Country Code selection feature to be disabled for products marketed to the US/CANADA
RoHS Directive 2011/65/EU
REACH Regulation (EC) No. 1907/2006
Operations in the 5.15-5.25GHz / 5.470 ~ 5.725GHz band are restricted to indoor usage only.
The band from 5600-5650MHz will be disabled by the software during the manufacturing
and cannot be changed by the end user. This device meets all the other requirements
specified in Part 15E, Section 15.407 of the FCC Rules.
© Copyright 2015 TRENDnet. All Rights Reserved.
65
Limited Warranty
TRENDnet User’s Guide
[Dutch]
Česky [Czech]
Dansk [Danish]
Deutsch
[German]
TRENDnet tímto prohlašuje, že tento TEW-818DRU je ve shodě se
základními požadavky a dalšími příslušnými ustanoveními směrnice
1999/5/ES.
Undertegnede TRENDnet erklærer herved, at følgende udstyr TEW818DRU overholder de væsentlige krav og øvrige relevante krav i
direktiv 1999/5/EF.
Hiermit erklärt TRENDnet, dass sich das Gerät TEW-818DRU in
Übereinstimmung mit den grundlegenden Anforderungen und den
übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG
befindet.
Eesti [Estonian]
Käesolevaga kinnitab TRENDnet seadme TEW-818DRU vastavust
direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist
tulenevatele teistele asjakohastele sätetele.
English
Hereby, TRENDnet, declares that this TEW-818DRU is in compliance
with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente TRENDnet declara que el TEW-818DRU
cumple con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑTRENDnet ΔΗΛΩΝΕΙ ΟΤΙTEW-818DRU
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ
ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français
[French]
Par la présente TRENDnet déclare que l'appareil TEW-818DRU est
conforme aux exigences essentielles et aux autres dispositions
pertinentes de la directive 1999/5/CE.
Italiano[Italian]
Con la presente TRENDnet dichiara che questo TEW-818DRU è
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti
stabilite dalla direttiva 1999/5/CE.
Latviski [Latvian]
AršoTRENDnetdeklarē, ka TEW-818DRU deklarē, ka [type of
equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām
prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių
[Lithuanian]
Nederlands
Malti [Maltese]
Magyar
[Hungarian]
Polski [Polish]
overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG.
Hawnhekk, TRENDnet, jiddikjara li dan TEW-818DRU jikkonforma
mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm
fid-Dirrettiva 1999/5/EC.
Alulírott, TRENDnet nyilatkozom, hogy a TEW-818DRU megfelel a
vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv
egyéb elõírásainak.
Niniejszym TRENDnet oświadcza, że TEW-818DRU ] jest zgodny z
zasadniczymi wymogami oraz pozostałymi stosownymi
postanowieniami Dyrektywy 1999/5/EC.
Português
[Portuguese]
TRENDnet declara que este TEW-818DRU está conforme com os
requisitos essenciais e outras disposições da Directiva 1999/5/CE.
Slovensko
[Slovenian]
TRENDnet izjavlja, da je ta TEW-818DRU v skladu z bistvenimi
zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.
Slovensky
[Slovak]
TRENDnettýmtovyhlasuje, že TEW-818DRU spĺňa základné
požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
Suomi [Finnish]
Svenska
[Swedish]
TRENDnet vakuuttaa täten että TEW-818DRU tyyppinen laite on
direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien
direktiivin muiden ehtojen mukainen.
Härmed intygar TRENDnet att denna TEW-818DRU står I
överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Šiuo TRENDnet deklaruoja, kad šis TEW-818DRU atitinka esminius
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Hierbij verklaart TRENDnet dat het toestel TEW-818DRU in
© Copyright 2015 TRENDnet. All Rights Reserved.
66
Limited Warranty
TRENDnet User’s Guide
ErP Statement
English
energia.
This network device is an Energy Related Product (ErP) that
automatically switches to a power saving standby mode within 10
minutes of no data transmission. When the device is not in use it can
be powered down using its power button, or simply disconnect the
power adapter for additional energy savings.
Modalità standby in rete: 0.5 watt
Modalità spento: 0.15 watts
Português
[Portuguese]
Networked standby mode: 0.5 watts
Off mode: 0.15 watts
Deutsch [German]
Dieses Netzwerkgerät ist ein Energy Related Product (ErP), das
innerhalb von 10 Minuten ohne Datenübertragung automatisch in
einen Stromsparmodus umschaltet. Wenn das Gerät nicht verwendet
wird, kann es über die Ein-/Austaste heruntergefahren werden, oder
ziehen Sie für zusätzliche Stromersparnis das Netzgerät aus der
Steckdose.
Vernetzt und in Bereitschaft: 0.5 Watt
Ausgeschaltet: 0.15 watts
Français [French]
Ce périphérique réseau est un Energy Related Product (ErP) qui passe
automatiquement en mode veille, économisant l’énergie, après 10
minutes sans transfert de données. Lorsque le périphérique n’est pas
utilisé, il peut être éteint en utilisant le bouton d’alimentation, ou
simplement déconnecté en débranchant l’adaptateur secteur pour
obtenir davantage d’économies d’énergie.
Este dispositivo de rede é um Produto de Consumo de Energia (ErP)
que alterna automaticamente para modo de espera com economia
de energia após 10 minutos sem transmissão de dados. Quando o
dispositivo não está sendo usado pode ser desligado no botão de
energia, ou simplesmente desligando o adaptador de corrente para
economia de energia adicional.
Modo de espera em rede: 0.5 watts
Modo off: 0.15 watts
Русский [Russian]
Данное сетевое устройство - это продукт, относящийся к
категории потребителей электрической энергии (ErP), которые
переходят в экономный режим ожидания, если в течение 10
минут не осуществляется передача данных. Когда устройство не
используется, его можно отключить от источника питания путем
нажатия кнопки включения или путем физического отключения
адаптера питания.
В режиме ожидания: 0.5 Ватт
В выключенном состоянии: 0,15 Ватт
Mode veille en réseau : 0.5 Watt
Mode éteint : 0.15 watts
Español [Spanish]
Este dispositivo de red es un producto relacionado con la energía
(ErP) que pasa automáticamente a un modo en espera, de ahorro de
energía, tras 10 minutos de ausencia de transmisión de datos.
Cuando el dispositivo no está en uso, se puede apagar utilizando el
botón de alimentación, o simplemente desconectar el adaptador de
corriente para optimizar el ahorro de energía.
Modo de espera en red: 0.5 vatios
Modo apagado: 0.15 vatios
Italiano[Italian]
Questo apparato di rete è un Energy Related Product (ErP) il quale
commuta automaticamente in una modalità standby entro 10 minuti
dall’interruzione della trasmissione di dati. Quando l’apparato non
viene utilizzato, può essere spento tramite il tasto di accensione, o si
può scollegare l’alimentatore, per ottenere un maggior risparmio di
© Copyright 2015 TRENDnet. All Rights Reserved.
67
TRENDnet User’s Guide
Limited Warranty
Industry Canada Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum
de 20 cm de distance entre la source de rayonnement et votre corps.
© Copyright 2015 TRENDnet. All Rights Reserved.
68
Limited Warranty
TRENDnet User’s Guide
Limited Warranty
TRENDnet warrants its products against defects in material and workmanship, under
normal use and service, for the following lengths of time from the date of purchase.
TEW-818DRU – 3 Years Warranty
AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty.
If a product does not operate as warranted during the applicable warranty period,
TRENDnet shall reserve the right, at its expense, to repair or replace the defective
product or part and deliver an equivalent product or part to the customer. The
repair/replacement unit’s warranty continues from the original date of purchase. All
products that are replaced become the property of TRENDnet. Replacement products
may be new or reconditioned. TRENDnet does not issue refunds or credit. Please
contact the point-of-purchase for their return policies.
TRENDnet shall not be responsible for any software, firmware, information, or memory
data of customer contained in, stored on, or integrated with any products returned to
TRENDnet pursuant to any warranty.
There are no user serviceable parts inside the product. Do not remove or attempt to
service the product by any unauthorized service center. This warranty is voided if (i) the
product has been modified or repaired by any unauthorized service center, (ii) the
product was subject to accident, abuse, or improper use (iii) the product was subject to
conditions more severe than those specified in the manual.
Warranty service may be obtained by contacting TRENDnet within the applicable
warranty period and providing a copy of the dated proof of the purchase. Upon proper
submission of required documentation a Return Material Authorization (RMA) number
will be issued. An RMA number is required in order to initiate warranty service support
for all TRENDnet products. Products that are sent to TRENDnet for RMA service must
have the RMA number marked on the outside of return packages and sent to TRENDnet
prepaid, insured and packaged appropriately for safe shipment. Customers shipping
from outside of the USA and Canada are responsible for return shipping fees. Customers
shipping from outside of the USA are responsible for custom charges, including but not
limited to, duty, tax, and other fees.
WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE AS
WARRANTED ABOVE, THE CUSTOMER’S SOLE REMEDY SHALL BE, AT TRENDNET’S
OPTION, REPAIR OR REPLACE. THE FOREGOING WARRANTIES AND REMEDIES ARE
EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,
EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING
© Copyright 2015 TRENDnet. All Rights Reserved.
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR
IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE
OR USE OF TRENDNET’S PRODUCTS.
TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND
EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST
OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT,
IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR
MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY
ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO
EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN
CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL,
INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR
PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER FINANCIAL
LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION,
MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY
OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND
OF THE PURCHASE PRICE PAID, AT TRENDNET’S OPTION. THIS DISCLAIMER OF LIABILITY
FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL
OF ITS ESSENTIAL PURPOSE.
Governing Law: This Limited Warranty shall be governed by the laws of the state of
California.
Some TRENDnet products include software code written by third party developers.
These codes are subject to the GNU General Public License ("GPL") or GNU Lesser
General Public License ("LGPL").
Go to http://www.trendnet.com/gpl or http://www.trendnet.com Download section
and look for the desired TRENDnet product to access to the GPL Code or LGPL Code.
These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of
the developers. TRENDnet does not provide technical support for these codes. Please go
to http://www.gnu.org/licenses/gpl.txt or http://www.gnu.org/licenses/lgpl.txt for
specific terms of each license.
PWP05202009v2
2014/12/23
69


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Copy, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2015:12:28 15:54:31+08:00
Creator Tool                    : Microsoft® Word 2013
Modify Date                     : 2015:12:28 15:54:50+08:00
Metadata Date                   : 2015:12:28 15:54:50+08:00
Format                          : application/pdf
Creator                         : Jonathan
Title                           : test 3
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Document ID                     : uuid:cb31755f-fff6-4712-a446-a688579c3cdc
Instance ID                     : uuid:8a3c4d56-2425-4ce8-96df-b1274eb79e36
Page Count                      : 70
Author                          : Jonathan

EXIF Metadata provided by EXIF.tools