TRENDNET THA101 Home Smart Switch User Manual

TRENDNET, Inc. Home Smart Switch

User manual

THA-101 WiFi Smart Plug Quick Install GuideSetup for Repeater Mode 1 Power on the Extender Step1. Plug your Wireless Extender into anelectrical socket. Step2. Check the LEDs: the power LED should be always on when system isready. Connect to the Wireless Extender 2Step1. Default SSID is “THA-101” andsecurity key is “12345678”. Step2. Set your wireless adapter in DHCPclient and waiting for getting IPAddress from the Wireless Extender.Step3. Open a web browser and enter “192.168.1.254” in URL field to openthe configuration page. Step4. Default user name is “admin” and password is “password” to accessWEB GUI. 3Manually Configuration: Step1. Open Wireless Settings / AP Clientpage. Step2. Setup the SSID and Security of APthat you want to connect to: ClickAPPLY to finish. Notes: The Wireless Extender is designed as a pure wirelessdevice, so there are no any RJ-45 ports for Ethernetcable to connect to. Please prepare any IEEE802.11ac/b/g/n compliant wireless adapter for next setupstep. OR you can use “SCAN” to refresh thewireless network and select an AP toconnect to. “Theproductshallbeusedintheresidentialenvironmentnotwithstandinguseincommercial,businessenvironments.Ifyouwanttouseotherthantheaboveenvironments,pleasecontactAboComfirst.” WPS Configuration: Step1. Press the WPS button of the Wireless Extender over 3 seconds. Step2. Then press the WPS button of the wireless router/AP over 3 seconds too. Step 1 and Step 2 need to be done in 200 seconds.
FCC Statement: Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. Check if Connected 4The green–checked icon ahead is the Wireless Router/AP which the Wireless Extender is working to. WPS button behavior: Less than 2 sec → N/A, WPS LED no blinking. More than 2 sec → Do WPS, WPS LED start blinking Reset button behavior: Less than 2 sec → N/A, D5-D1 LEDs no blinking. 2-5 seconds → Do REBOOT, D5-D1 LEDs fast blinking.More than 5 sec→ Do Factory Default, D5-D1 LEDs blinking slowly. Hardware Button Behavior 5
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Navigation menu