TRIMBLE EUROPE 802168 MobileMapper 20, WCDMA/GSM/GPS Portable Receiver User Manual NZI802168 09x

Download:
Mirror Download [FCC.gov]
Document ID	2218072
Application ID	Nkc2Bob2V0AVDKh/riHFiw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	80.95kB (1011910 bits)
Date Submitted	2014-03-18 00:00:00
Date Available	2014-03-18 00:00:00
Creation Date	2014-01-14 18:57:33
Producing Software	Acrobat Distiller 9.5.5 (Windows)
Document Lastmod	2014-01-14 18:57:33
Document Title	Microsoft Word - NZI802168_User manual 09.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	jiaxing.ye

MobileMapper
20
®
Getting Started Guide
Copyright Notice
Copyright 2013 Trimble Navigation Limited. All rights
reserved.
Trademarks
All product and brand names mentioned in this
publication are trademarks of their respective holders.
SPECTRA PRECISION LIMITED WARRANTY TERMS AND
CONDITIONS
PRODUCT LIMITED WARRANTY ‐ Subject to the following
terms and conditions, Spectra Precision warrants that for
a period of one (1) year from date of purchase this
Spectra Precision product (the “Product”) will
substantially conform to Spectra Precision’s publicly
available specifications for the Product and that the
hardware and any storage media components of the
Product will be substantially free from defects in
materials and workmanship.
PRODUCT SOFTWARE ‐ Product software, whether built
into hardware circuitry as firmware, provided as a
standalone computer software product, embedded in
flash memory, or stored on magnetic or other media, is
licensed solely for use with or as an integral part of the
Product and is not sold. If accompanied by a separate end
user license agreement (“EULA”), use of any such
software will be subject to the terms of such end user
license agreement (including any differing limited
warranty terms, exclusions, and limitations), which shall
control over the terms and conditions set forth in this
limited warranty.
SOFTWARE FIXES ‐ During the limited warranty period
you will be entitled to receive such Fixes to the Product
software that Spectra Precision releases and makes
commercially available and for which it does not charge
separately, subject to the procedures for delivery to
purchasers of Spectra Precision products generally. If you
have purchased the Product from a Spectra Precision
Authorized Distribution Partner rather than from Spectra
Precision directly, Spectra Precision may, at its option,
forward the software Fix to the Spectra Precision
Authorized Distribution Partner for final distribution to
you. Minor Updates, Major Upgrades, new products, or
substantially new software releases, as identified by
Spectra Precision, are expressly excluded from this
update process and limited warranty. Receipt of software
Fixes or other enhancements shall not serve to extend
the limited warranty period.
For purposes of this warranty the following definitions
shall apply: (1) “Fix(es)” means an error correction or
other update created to fix a previous software version
that does not substantially conform to its Spectra
Precision specifications; (2) “Minor Update” occurs when
enhancements are made to current features in a
software program; and (3) “Major Upgrade” occurs when
significant new features are added to software, or when
a new product containing new features replaces the
further development of a current product line. Spectra
Precision reserves the right to determine, in its sole
discretion, what constitutes a Fix, Minor Update, or
Major Upgrade.
WARRANTY REMEDIES ‐ If the Spectra Precision Product
fails during the warranty period for reasons covered by
this limited warranty and you notify Spectra Precision of
such failure during the warranty period, Spectra Precision
will repair OR replace the nonconforming Product with
new, equivalent to new, or reconditioned parts or
Product, OR refund the Product purchase price paid by
you, at Spectra Precision’s option, upon your return of
the Product in accordance with Spectra Precision’s
product return procedures then in effect.
HOW TO OBTAIN WARRANTY SERVICE ‐ To obtain
warranty service for the Product, please contact your
local Spectra Precision Authorized Distribution Partner.
Alternatively, you may contact Spectra Precision to
request warranty service at +1‐303‐323‐4100 (24 hours a
day)
or
e‐mail
your
request
to
support@spectraprecision.com. Please be prepared to
provide:
•
your name, address, and telephone numbers
•
•
•
•
proof of purchase
a copy of this Spectra Precision warranty
a description of the nonconforming Product
including the model number
an explanation of the problem
The customer service representative may need
additional information from you depending on the
nature of the problem.
WARRANTY EXCLUSIONS AND DISCLAIMER ‐
This Product limited warranty shall only apply in the
event and to the extent that (a) the Product is properly
and correctly installed, configured, interfaced,
maintained, stored, and operated in accordance with
Spectra Precision’s applicable operator's manual and
specifications, and; (b) the Product is not modified or
misused. This Product limited warranty shall not apply to,
and Spectra Precision shall not be responsible for, defects
or performance problems resulting from (i) the
combination or utilization of the Product with hardware
or software products, information, data, systems,
interfaces, or devices not made, supplied, or specified by
Spectra Precision; (ii) the operation of the Product under
any specification other than, or in addition to, Spectra
Precision standard specifications for its products; (iii) the
unauthorized installation, modification, or use of the
Product; (iv) damage caused by: accident, lightning or
other electrical discharge, fresh or salt water immersion
or spray (outside of Product specifications); or exposure
to environmental conditions for which the Product is not
intended; (v) normal wear and tear on consumable parts
(e.g., batteries); or (vi) cosmetic damage. Spectra
Precision does not warrant or guarantee the results
obtained through the use of the Product, or that
software components will operate error free.
NOTICE REGARDING PRODUCTS EQUIPPED WITH
TECHNOLOGY CAPABLE OF TRACKING SATELLITE
SIGNALS FROM SATELLITE BASED AUGMENTA‐
TION SYSTEMS (SBAS) (WAAS/EGNOS, AND
MSAS), OMNISTAR, GPS, MODERNIZED GPS OR GLONASS
SATELLITES, OR FROM IALA BEACON
SOURCES: SPECTRA PRECISION IS NOT RESPON‐
SIBLE FOR THE OPERATION OR FAILURE OF OPERATION OF
ANY SATELLITE BASED POSITIONING SYSTEM OR THE
AVAILABILITY OF ANY SATELLITE BASED POSITIONING
SIGNALS.
THE FOREGOING LIMITED WARRANTY TERMS
STATE SPECTRA PRECISION’S ENTIRE LIABILITY,
AND YOUR EXCLUSIVE REMEDIES, RELATING TO
THE SPECTRA PRECISION PRODUCT. EXCEPT AS
OTHERWISE EXPRESSLY PROVIDED HEREIN, THE
PRODUCT AND ACCOMPANYING DOCUMENTATION AND
MATERIALS ARE PROVIDED “AS‐IS”
AND WTHOUT EXPRESS OR IMPLIED WARRANTY OF ANY
KIND, BY EITHER SPECTRA PRECISION
OR ANYONE WHO HAS BEEN INVOLVED IN ITS
CREATION, PRODUCTION, INSTALLATION, OR DIS‐
TRIBUTION, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILI‐
TY AND FITNESS FOR A PARTICULAR PURPOSE,
TITLE, AND NONINFRINGEMENT. THE STATED EX‐
PRESS WARRANTIES ARE IN LIEU OF ALL OBLI‐
GATIONS OR LIABILITIES ON THE PART OF
SPECTRA PRECISION ARISING OUT OF, OR IN
CONNECTION WITH, ANY PRODUCT. BECAUSE
SOME STATES AND JURISDICTIONS DO NOT ALLOW
LIMITATIONS ON DURATION OR THE EXCLU‐
SION OF AN IMPLIED WARRANTY, THE ABOVE
LIMITATION MAY NOT APPLY OR FULLY APPLY TO YOU.
YOUR LOCAL SPECTRA PRECISION AUTHORIZED
DISTRIBUTION PARTNER FOR APPLICABLE WARRANTY
INFORMATION.
LIMITATION OF LIABILITY ‐ SPECTRA PRECISION’S ENTIRE
LIABILITY UNDER ANY PROVI‐
SION HEREIN SHALL BE LIMITED TO THE
AMOUNT PAID BY YOU FOR THE PRODUCT. TO
THE MAXIMUM EXTENT PERMITTED BY APPLICA‐
BLE LAW, IN NO EVENT SHALL SPECTRA PRECI‐
SION OR ITS SUPPLIERS BE LIABLE FOR ANY
INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGE WHATSOEVER UNDER ANY
CIRCUMSTANCE OR LEGAL THEORY RELATING IN ANYWAY
TO THE PRODUCTS, SOFTWARE, AND ACCOMPANYING
DOCUMENTATION AND MATERIALS,
(INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS OF BUSINESS PROFITS, BUSINESS
INTERRUPTION, LOSS OF DATA, OR ANY OTHER
PECUNIARY LOSS), REGARDLESS OF WHETHER
SPECTRA PRECISION HAS BEEN ADVISED OF THE
POSSIBILITY OF ANY SUCH LOSS AND REGARD‐
LESS OF THE COURSE OF DEALING WHICH DEVELOPS OR
HAS DEVELOPED BETWEEN YOU AND SPECTRA
PRECISION. BECAUSE SOME STATES
AND JURISDICTIONS DO NOT ALLOW THE EXCLU‐
SION OR LIMITATION OF LIABILITY FOR CONSE‐
QUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE
LIMITATION MAY NOT APPLY OR FULLY APPLY TO YOU.
Charge battery only at ambient temperatures ranging
from 0°C to 60°C.
(1)CAUTION: Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent type
of battery recommended by the manufacturer. Dispose
of used batteries according to battery manufacturer’s
instructions.
PLEASE NOTE: THE ABOVE SPECTRA PRECISION
WARRANTY PROVISIONS WILL NOT APPLY TO PRODUCTS
PURCHASED IN THOSE JURISDICTIONS (E.G., MEMBER
STATES OF THE EUROPEAN
ECONOMIC AREA) IN WHICH PRODUCT WARRAN‐
TIES ARE THE RESPONSBILITY OF THE LOCAL
SPECTRA PRECISION AUTHORIZED DISTRIBUTION
PARTNER FROM WHOM THE PRODUCTS ARE
ACQUIRED. IN SUCH A CASE, PLEASE CONTACT
CAUTION: Use of USB data cables is restricted to standard
USB version 2.0 or higher. Powered USB is prohibited.
OFFICIAL LANGUAGE ‐ THE OFFICIAL LANGUAGE
OF THESE TERMS AND CONDITIONS IS ENGLISH.
IN THE EVENT OF A CONFLICT BETWEEN ENGLISH AND
OTHER LANGUAGE VERSIONS, THE ENGLISH LANGUAGE
SHALL CONTROL.
REGISTRATION ‐ To receive information regarding
updates and new products, please contact your local
Spectra Precision Authorized Distribution Partner or
visit the Spectra Precision website at
www.spectraprecision.com/register. Upon registration
you may select the newsletter, upgrade, or new product
information you desire.
PRODUCT SAFETY WARNINGS
Use responsibly. Read all instructions and safety
information before use to avoid injury.
The maximum operating ambient temperature of the
equipment declared by the manufacturer is 60°C.
Battery safety
(2)CAUTION: RISK OF EXPLOSION IF BATTERY IS
REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS.
(2)CAUTION: RISK OF EXPLOSION IF BATTERY IS
REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS.
Wi‐Fi Safety
Turn Wi‐Fi off in areas where Wi‐Fi use is prohibited or
when it may cause interference or danger, such as in
airplanes while flying.
Care & Maintenance
Excessive sound pressure from
headphones can cause hearing loss.
USB data cables
earphones
and
Hand Strap
Use the hand strap responsibly. It is primarily designed
to ease handheld use of the product (limbworn). The
hand strap should not be used to attach the product
next to the body.
Table of Contents
First‐Time Use..................................................................................................1
Unpacking...................................................................................................1
Inserting the Battery Into the Receiver.......................................................1
Turning the Receiver On..............................................................................2
Using the AC Adapter to Charge the Battery ..............................................3
Using the Quick Toolbar...............................................................................4
Switching the Receiver Manually to Suspend Mode...................................4
Adjusting Backlight Level and Idle Time .....................................................4
Power Management....................................................................................5
Setting Time & Date ....................................................................................5
Regional Settings .........................................................................................6
Locking the Screen and the Keypad.............................................................6
How to Hold the Receiver............................................................................7
Turning the Receiver Off ..............................................................................7
Receiver Description.........................................................................................8
Front View ..................................................................................................8
Rear View ...................................................................................................9
Bottom View.............................................................................................. 10
GNSS Toolbox..............................................................................................11
GNSS Settings .............................................................................................11
GNSS Status.................................................................................................11
Reset ...........................................................................................................12
About.............................................................................................................12
Advanced Features..............................................................................................13
Power Modes.................................................................................................13
Internal Battery..............................................................................................13
USB Connection.............................................................................................15
Wireless Communication ..............................................................................16
Motion Sensor...............................................................................................17
Using the Camera..........................................................................................18
Making a Video..............................................................................................20
E‐Compass Calibration.........................................................................................23
Platform Specifications........................................................................................24
GNSS Characteristics.......................................................................................24
Accuracy Specifications ..................................................................................24
Processor.........................................................................................................24
Operating System ...........................................................................................24
Communication...............................................................................................24
Physical Characteristics...................................................................................25
User Interface ..........................................................................................25
Memory ....................................................................................................25
Environmental Characteristics....................................................................25
Power Requirements...................................................................................25
Multimedia & Sensors.................................................................................25
Software Options.........................................................................................25
Standard Accessories.................................................................................26
First-Time Use
Unpacking
Open the receiver box and unpack the following items:
• Receiver
• Battery
• Universal AC adapter
• USB cable
• Hand strap
• Lanyard
Inserting the
Battery Into
the Receiver
• Stylus
Follow the instructions below:
• Turn over the receiver.
• Using the top end of the stylus (or a coin), rotate the two
screws to open the trap door: turn the left‐hand one
clockwise by a quarter turn, and the right‐hand one
anticlockwise, also by a quarter turn.
• Pull the trap door open.
• Insert the battery as shown. Orientate the battery so that its
electric contacts can come into contact with those at the
bottom of the battery compartment. Insert the upper part of
the battery first, as shown, then push the battery in.
• Put the trap door back into place by first inserting the two lugs
located at the bottom of the trap door.
• Then push the door against the receiver case and rotate the
two screws back in their initial positions to seal the battery
compartment.
Turning the Press the Power key [1] for a couple of seconds until you feel
•
Receiver On
a vibration in your hand, then release the key.
[1]
Let the receiver run its boot sequence. Wait until the screen
displays the Windows Embedded Hand Held
Home screen. At this stage, you may be asked to initialize the
receiver (screen alignment, etc.). Just follow the instructions
on the screen to complete this step.
The operating system used in the receiver is Microsoft
Windows Embedded Hand Held. For more information on
how to use the different applications, you can visit the
Microsoft web site at:
http://www.microsoft.com/windowsembedded/enus/windowsembedded-handheld-6-5.aspx
Depending on how long your product was stored in its package
before being shipped to you, the remaining power in the battery
may be too low to allow the receiver to operate for your entire
working session. For this reason, the first thing to do is to check
the battery charge status:
• Tap on the title bar at the top of the screen. The Quick Toolbar
appears just underneath.
• Tap on the Battery icon. This opens the Power window and
simultaneously closes the Quick Toolbar.
The Power window shows the status of the battery (see also
Internal Battery on page 13) . If the remaining power is
greater than 50%, then you can use the receiver without
having to charge the battery first (with 50% of remaining
charge, you can use the receiver for several hours). Skip the
next section and go directly to Adjusting Backlight Level and
Idle Time on page 4.
Using the AC
Adapter to
Charge the
Battery
• If it less, Spectra Precision recommends you first charge the
battery as explained in Using the AC Adapter to Charge the
Battery on page 3.
Follow the instructions below.
•
Prepare the AC adapter:
– Remove the protective cover [1] by pushing the button
– Choose the plug that fits your country’s AC outlet standard (see
[2]) and slide it into the AC adapter [3].
( A “click” must be heard when fully inserted. )
• Take the USB cable provided [4]. Connect the end fitted with a
standard USB connector to the AC adapter. Connect the other
end (fitted with a mini‐USB connector) to the bottom side of the
receiver (open the flap [5] first).
[4]
[5]
[3]
[4]
[4]
• Connect the AC adapter to an electric outlet. After about 4
seconds, the receiver screen lights up. An icon shows up
indicating that the battery is being charged. The screen is then
turned back off after about 10 seconds. After this time, battery
charging will continue at the same rate until the battery is fully
charged (charging time: 4 hours max.).
• To read the battery charging status using the Quick Toolbar, refer
to the instructions in Turning the Receiver On on page 2 (see also
Using the Quick Toolbar on page 4).
Using the Quick
Toolbar
Windows offers a quick toolbar allowing you to quickly access
frequently used functions (zoom, Bluetooth, WiFi, phone,
sound volume, battery power and clock).
• Tap on the title bar at the top of the screen. The quick
toolbar appears just underneath.
simultaneously closes the quick toolbar.
The zoom function enlarges the screen content, which means
only part of the screen is shown at a time, and so you should
drag the stylus over the screen to scroll through the whole
display.
To return to 1:1 zoom, tap on the title bar again to re‐open the
quick toolbar, then tap on the zoom function again.
Switching the
Receiver Manually
to Suspend Mode
Switching the receiver to Suspend mode is the right thing to do
when you need to make a short pause in your work and you want
to save the operating time of your battery. You should not
however switch the receiver to Suspend mode when it is
collecting raw data.
In Suspend mode, the receiver is idle, using the minimum of
energy required to save the use context.
To switch to Suspend mode, just press briefly on the Power
button [1]. The receiver screen is turned off instantly.
Adjusting
Backlight Level
and Idle Time
To wake up the receiver, just press briefly the same button again.
This will instantly switch the screen back on and restore the use
context in which the receiver was before entering the Suspend
mode.
Backlight Level: The screen backlight may be adjusted to match
the ambient light for optimized visibility. You don’t need the same
level of screen backlight in dark areas than in
• Run the desired function by just tapping on the corresponding
icon. This runs the requested function and hot sun.
Backlight Idle Time: One way of saving the battery is to avoid
those periods of time during which the screen backlight is
unnecessarily on. As the receiver automatically counts the time
during which neither the keypad nor the touch screen is active,
you can set the receiver to turn off the backlight automatically
after a certain idle time.
Follow the instructions below to set these two parameters:
• Press the Windows key and tap successively on Settings,
System and Backlight.
• Tap on the Battery Power tab.
• Drag the cursor to the right or left to set the screen backlight to
the desired level (between Dark and Bright). The resulting
brightness is obtained when you release the cursor.
• Tick the Turn off backlight if device... check box and then
choose the idle time before the backlight is turned off
(10 seconds, 30 seconds or 1 to 5 minutes)
Note that the backlight level and idle time can be set to
different values for when the receiver is operated from an
external power source instead of its internal battery. You can
make these settings after tapping on the External Power
tab.
• Tap OK to save all your changes and return to the previous
screen.
Power Another way of saving the battery is to allow the receiver to
Management switch automatically to Suspend mode after a certain period
Setting Time & Date
of inactivity.
• Press the Windows key and tap successively on Settings,
System and Power.
• Tap on the Advanced tab. This tab allows you to ask for the
receiver to switch automatically to Suspend mode if it stays
idle for the period of time you choose. You may choose a
different setting depending on whether the receiver is
powered from the internal battery or from an external power
source.
• Tap OK to save the settings and return to the previous screen.
Remember that the receiver should NOT be allowed to switch
automatically to Suspend mode if it is expected to collect data for
a long period of time
and you know the
keyboard will be left
idle during this time.
• Press the Windows key and tap successively on Settings,and
Clock & Alarms.
• On the Time tab, select your time zone and then enter the
local date and time.
• Tap OK to save your settings.
Regional Settings
It’s a good idea to customize your receiver so that it complies with
a number of local preferences, such as country’s currency, decimal
point representation, time and date formats, etc.
• Press the Windows key and tap successively on Settings,
System and Regional Settings.
• On the Region tab, select your country.
• Use the other tabs to set your local settings:
– Number format
– Currency choice
– Time and date formats
• Tap OK to save the settings and return to the Today screen.
Locking the
Screen and the
Keypad
At some stage in your work, you may need to lock the receiver to
make sure no user intervention from the screen or keypad can
affect the work in progress.
• Press the Windows key.
• In the task bar at the bottom of the screen, tap on the padlock
icon (see screen below). As a result, the touch screen and keypad
are made inactive.
• To unlock the touch screen and keypad, just drag the onscreen
slide button either to the left or right. This will take you back to
the Home screen.
How to Hold the
Receiver
Tracking satellites with your receiver requires that you use the receiver
outdoor and hold it in an appropriate manner.
The receiver will have the best view of the sky when you hold it at
an angle of around 45 degrees from horizontal and not too close to
your body.
You can check that your receiver is tracking enough satellites by
running the GNSS Toolbox, and more particularly the GNSS Status
function (see GNSS Status on page 11). When enough satellites are
tracked, you can start using your receiver and run your application
software.
Turning the
Receiver Off
After you have finished your work, turn off your receiver by
holding the Power button [1] pressed until a Warning
message is displayed on the screen asking you to confirm the
power‐off request. Tap Yes. The receiver will shut down in the
next couple of seconds after a duo‐tone sound has been heard.
Receiver Description
Front View Power Key
Use the Power key [1] to turn on or off the receiver.
To turn on the receiver, press the Power key [1] until you can feel
a vibration in your hand, meaning the receiver has started a
power‐on procedure. You can then release the key.
To turn off the receiver press the Power key [1] until a sound is
heard and a warning message pops up on the screen asking you
to confirm the power shutdown request. Tap Yes on the screen.
A two‐tone sound can then be heard just before the receiver shuts
down.
Windows key
[8]
[9]
The Windows key [2] is used to give immediate and unconditional
access to the Windows Start menu.
Display Screen
The display screen [3] is a 3.5‐inch, VGA, 256‐color (18‐bit RGB) touch
screen (240 x 320 pixels).
[3]
Scroll / Enter keys
The Enter button [4] is used to accept highlighted input and initiate
various functions.
[1] [7] [4] [5] [2] [6]
The Scroll button [5] is the ring around the Enter button. It is used
to move the cursor on the screen, from one data field to the next
on a parameter screen, from one option to another in a menu, from
one geographical location to another on a map screen.
Function keys
The receiver is fitted with four function keys [6]. The specific function
of each of them is given in the table below.
Button
Function
The keypad includes two of these buttons, one on the
right, the other on the left.
Each of them is a convenient alternative to tapping on
the functions appearing just above in the task bar at the
bottom of the screen (e.g.
Notifications, Contacts, Menu, Log, etc.).
In Spectra Precision applications with a map screen
displayed, use this button to zoom in. In Windows
Embedded, displays the Start menu.
In Spectra Precision applications with a map screen
displayed, use this button to zoom out. In Windows
Embedded, displays the Phone screen.
Microphone
A microphone is used by the voice recorder. Keep the small aperture [7]
clear when recording a vocal comment.
Built-in GPS Antenna
The receiver incorporates a built‐in GPS antenna [8]. The receiver
should be held properly to optimize satellite reception.
Earpiece
As a multi‐media device, the receiver includes an earpiece [9],
which can be used by any voice‐based software application.
Rear View
[10] [11] [12]
[13]
External GPS Antenna Input
[14]
[15]
[16]
Use this input [10] to connect an external GPS antenna to the
receiver. When an external antenna is connected, the built‐in GPS
antenna is automatically disconnected from the receiver input.
The antenna input connector is protected by a rubber flap. Spectra
Precision recommends you keep the flap close when no external
antenna is used.
Loudspeaker
The back of the receiver incorporates a high‐quality loudspeaker [11].
[17]
10
Camera Lens
Keep the camera lens [12] clear when taking pictures or recording videos.
Hand strap
The hand strap provided may be attached to the back of the receiver
through two threaded holes [13] and [14] and the two recesses
located at the bottom of the receiver (see Bottom View below).
The hand strap may also accommodate the stylus, which can also be
attached to the leather strip of the hand strap using the lanyard
provided.
Battery Compartment
battery
directions
The receiver makes use of a rechargeable Li‐Ion
battery pack. Loosen the quarter‐turn screws [15]
[16] using the stylus (or a coin) to access the
compartment [17]. The two screws use opposite
rotation for opening and closing the trap door.
of
The
battery
and a micro SD card [19].
compartment can also accommodate a SIM card [18]
When putting back the trap door, insert the bottom first, push the trap door against the back of
the receiver and seal the battery compartment by fully rotating the two screws in the opposite
direction.
Information on battery charging: see Internal Battery on page 13.
Bottom View
The bottom view provides access to a standard mini‐USB connector
[20]. You first need to open the protective rubber flap [21], using a
finger nail or a sharp and rigid tip to pull the flap from its left‐hand side.
[22] [20] [21]
The mini‐USB port is used to connect the receiver to the AC adapter,
for a fast battery charging cycle, or to a computer for file transfer
through Microsoft ActiveSync. In both cases, you need to use the USB
cable provided.
Information on battery charging: see Internal Battery on page 13.
[23]
[24]
[23]
The bottom part of the receiver also accommodates a Reset button
[22], which is accessible after you have opened the rubber flap [21].
Should the receiver get stuck, you can press that button using a sharp
tool to restart the receiver.
Warning! Never use the Reset button while the receiver is operating
normally or you would definitively lose all the data you are collecting.
The bottom view also shows the two recesses [23] in which the hand
strap [24] can be anchored.
11
GNSS Toolbox
GNSS Toolbox
is used to control and monitor important
functions in your receiver. These are listed and detailed
below.
• GNSS Settings
: Constellations and frequencies used in the
receiver.
• GNSS Status
: Views GNSS reception monitoring screens.
• Reset: Resets the receiver.
• About
: Provides the software version of GNSS Toolbox.
GNSS Settings
• Open the GNSS Toolbox and tap on GNSS Settings. This
opens a new window where you can make the following settings:
– Tracking mode: Only the “GPS L1” option is
available, which means the receiver can only
operate from the L1 signal of the GPS constellation.
– Use SBAS check box: Check this box to enable
SBAS reception, clear it otherwise.
• Tap OK to confirm your choices and return to the GNSS Toolbox
window.
GNSS Status
12
•
Open the GNSS Toolbox and tap on GNSS Status.
The default Position tab shows the latitude, longitude and
altitude of the current position, as computed by the receiver,
as well the number of satellites used and the current PDOP
value.
If SBAS is used, the screen also shows the position status
( SDGPS ).
The unit used to express the current altitude (meters or feet)
depends on the region (language and country) you selected in
Start, Settings, System, Regional Settings.
• The Satellites tab displays a polar diagram showing the locations
in the sky of the tracked satellites. Different colors are used to
display the numbers of the visible satellites:
– Yellow characters: GPS satellites used
– Grey characters: Visible SBAS satellites. Also rejected GPS
satellites, because unhealthy or under the elevation mask.
• The Signal tab shows the signal level for each of the tracked
satellites:
– Dark blue bars for all GPS satellites used
– Red bars for all SBAS satellites used
– Grey bars for all tracked, but not used, GPS satellites
GPS satellites are numbered from 1 to 32 and SBAS satellites from
120 to 138.
Reset • Open the GNSS Toolbox and tap on Reset. A message then
asks you if you want to reset the receiver now. Use this option
only if you think the receiver is not working properly.
Using this function results in a cold reset of the receiver.
Through a cold reset, all the GNSS settings, including almanac
data, are cleared making it necessary for you to restore each
of them manually. A few minutes are needed after a cold reset
before the receiver is back to work.
Using the Reset function is recommended when only the GNSS
Toolbox (and not other field software) is running on the
platform.
About This function provides the software version of GNSS Toolbox, followed
by the Spectra Precision legal line.
13
Advanced Features
Power Modes
The receiver has three power modes:
• Shutdown: The receiver is off.
• On: The receiver is fully powered
• Suspend: In this mode, the screen content and backlight are
turned off to save power and the use context is saved. When
quitting the Suspend mode, the use context is restored
instantly. Typically this mode is used in the field to allow a
quick restart after a pause.
The receiver can also enter the Suspend mode
automatically in case of a very low battery after dismissing
successively the two “low battery” alerts, or after an idle time
that you can set through a press on the Windows key, and
selecting Settings, Power (Advanced tab) (See also Power
Management on page 5).
Suspend Mode
The receiver can be switched to Suspend mode. This is a power
saving mode typically used in the field to allow a quick restart after
a pause. In this mode, only some parts of the receiver are
powered for the sole purpose of restoring the context of use in
which the receiver was when it was switched to Suspend mode.
The receiver should NOT however be used in that mode while
collecting raw data.
The receiver can also enter the Suspend mode automatically in
case of a very low battery after dismissing successively the two
“low battery” alerts, or after an idle time that you can set through
a press on the Windows key, then Settings, System and Power
(Advanced tab) (See also Power Management on page 5). When
collecting raw data, please clear this option so that the receiver
can never enter this mode.
Internal Battery Monitoring the Battery Discharging Status
The receiver will continuously inform you of the current status of
the battery through an icon located in the Windows Embedded
title bar (on the right). The different shapes of this icon indicate
the current discharging status, as listed below:
14
Icon
Meaning
Battery high: Remaining power ranges between
approximately 75 and 100% of full charge.
Approx. 50-75% remaining
Approx 25-50% remaining
Approx. 10-25% remaining
Battery low: Remaining power is less than 5%.
Receiver powered from external source (AC adapter,
computer via
USB line)
At any time you can read more in detail the battery status by
pressing the Windows key and then selecting Settings, System,
Power (see screen example).
When the remaining power drops below 10% of full charge
(orange area), you will see the message “Main Battery Low”
prompting you to replace or recharge the battery. Tap Dismiss in
the task bar. You should consider replacing the battery for a fresh
one but you may still continue to use the receiver for a while.
With only about 5% of remaining power (red area), a new
message will pop up: “Main Battery Very Low”. Tap Dismiss in
the task bar to continue using the receiver. Spectra Precision
however recommends that you turn off the receiver and replace
the battery.
With only about 1% of remaining power, the receiver will switch off,
meaning the battery is no longer charged enough to ensure proper
operation of the receiver. Spectra Precision recommends you do not
go that far in the use of the internal battery as there is a risk of
losing part of your field data.
In case of
regularly,
batteries.
long‐time storage, remember Li‐Ion batteries must always be recharged
about every six months. This is to prevent irreversible damage of the
Battery Charging Scenarios
The battery can be charged in two different ways:
• From the power line, through the AC adapter and USB cable
provided. This configuration offers fast battery charging, with
around 700 mA of DC charging current.
• From an office computer connected to the receiver through a
USB line, using the same USB cable provided. According to the
USB 2.0 specification, the DC current delivered will be limited
to 500 mA, which means it will take longer to charge the
battery from a computer’s USB port than from the AC adapter.
15
You can ask the receiver not to allow the charging of the
battery through the USB port when this port is connected to a
computer. To do this:
– Press the Windows key
– Select Settings, System, Power
– Clear the option: When equipment opens and
links to PC, do not carry out battery charging
– Tap OK.
Extracting the Battery from the Compartment
Lever the battery out of its compartment using the stylus or a flat
screwdriver. (The flat end of the stylus is inserted in the groove
located on the bottom side of the battery, as shown below.)
Likewise, extracting the SIM card or micro SD card from the
battery compartment requires the use of a spiky‐tipped tool to
pull the card out of its slot.
USB Connection
By default, the mini‐USB connector is set to allow a
connection to a computer using Active Sync. You just need to
connect the USB cable provided between the receiver’s miniUSB
connector and any computer fitted with a standard USB connector.
Provided Microsoft ActiveSync has been installed on the
computer, a serial connection will be initiated automatically when
you plug the cable. You can then use this connection to exchange
files, explore the receiver’s file system, install new applications
directly from the computer, etc.
16
If you want to make a different use of the receiver’s USB output,
press the Windows key, go to Settings>Connections> USB
to PC and change the settings accordingly.
Wireless
Communication
The receiver incorporates three wireless communication devices:
• Bluetooth
• WiFi
• GSM/GPRS Modem
The three devices can be controlled from the Wireless
Manager icon (press the Windows button and go to
Settings>Connections>Wireless Manager).
Bluetooth
Follow the procedure below to turn on Bluetooth and make a
connection with another system, which is supposed to have its
Bluetooth been turned on and made visible to others.
• Press the Windows key and tap successively on Settings and
Bluetooth.
• Tap on the Mode tab.
• Activate Turn on Bluetooth.
• Tap on the Devices tab.
• Tap on Add new device. Wait until the external system is found
• Tap on the name of this system, tap Next, enter a passcode
( optional) and then choose the Bluetooth service available on
this system that you would like to use now.
• Complete the connection setup as instructed.
Being only a Bluetooth client, the receiver will not offer any
Bluetooth services to external systems.
WiFi
The integrated Wi‐Fi device allows you to access the Internet
through a wireless connection.
• Press the Windows key and tap successively on Settings,
Connections and Wi-Fi.
• Tap on the Wireless tab.
17
• Tap on Search for Networks to turn on Wi‐Fi and start
searching for the networks that are available from your location.
• Choose one, then follow the instructions until you are given
access to the Internet.
GSM/GPRS Module
Provided the appropriate SIM card has previoulsy been inserted
in the battery compartment, the GSM/GPRS modem allows you
to:
• Make a phone call (modem used in GSM mode)
• Establish an Internet connection (modem used in GPRS mode).
Motion Sensor
Enabling Automatic Screen Rotation
By default, the receiver screen is used in portrait format. Rotating
the receiver by 90° will not cause the screen format to switch to
landscape format.
Operating the receiver this way is usually what you expect from
your receiver because you need to keep it always in portrait
position, with an angle of 45° for best satellite reception.
You can however ask the receiver to rotate the display automatically,
depending on the position you give to the receiver.
• Press the Windows key and tap successively on Settings, System
and Motion Sensor.
• Tap on the switch tab
• Enable the Screen rotation function. Using the Sensitivity cursor,
you can also adjust the sensitivity with which the receiver will react
to motion.
• Tap OK to validate all your settings.
Disabling Automatic Screen Rotation
Just before disabling the Screen rotation function (see above),
make sure the current screen format (portrait or landscape) is the
one you wish to use. If it’s not, first rotate the receiver accordingly
so you get this screen format, and then you can disable the
Screen rotation function.
Scrolling through Your Picture Gallery
18
By setting the motion sensor as a switch, you can easily go
through all your pictures or audio files, just using the hand that
holds the receiver, leaving your other hand free.
After you have opened the MyPictures folder for example and
tapped on the first picture to view it, you just need to shake the
receiver briefly to view the next one, and so forth until all the
pictures in the folder have been viewed.
To set the motion sensor as a switch:
• Press the Windows key and tap successively on Settings, System
and Motion Sensor.
• Tap on the switch tab
• Enable the Switch songs or pictures function and tap OK.
Fall Alarm
You may set the receiver to produce a sound alarm when it falls down:
• Press the Windows key and tap successively on Settings, System
and Motion Sensor.
• Tap on the Fall Alarm tab
• Enable the Fall Alarm function and tap OK.
Using the Camera Taking a Picture
• Press the Windows key and tap Pictures & Videos. This opens the
“My Pictures” folder in which you can see the list of existing images
and videos. The first item in the list is the Camera, the tool you will
now be using to take pictures. The light‐blue background means the
camera is currently selected.
• Tap Camera, or press the Enter button, to turn on the camera. Wait
a couple of seconds until the center of the window displays the
viewfinder of the camera.
• Now use the receiver as a camera. Look at the viewfinder to frame
the picture you want to take.
• When you are ready, stay as still as possible and press the Enter
button to take the picture. When you hear the click of the camera,
stay still for another two seconds until the screen displays the picture
you have just taken.
• Tap OK to come back to the viewfinder, then tap anywhere on the
screen to re‐activate the task bar a the bottom of the screen.
• Tap OK to turn off the camera and close the window. The picture
you have taken is now visible in the “My Pictures” folder.
19
Renaming a Picture
• With the “My Pictures” folder open, tap on the desired picture. This
opens a new window showing the picture.
• Tap Menu and Properties.
• Rename the file and tap OK.
Rotating a Picture
• With the “My Pictures” folder open, tap on the desired picture (or
tap on View in the task bar). This opens a new window showing the
picture.
• Tap Menu and Edit.
• Tap Rotate in the task bar. This rotates the image 90° clockwise.
Repeat the operation until the image has the right orientation.
• Tap OK to save the image.
Cropping a Picture
• With the “My Pictures” folder open, tap on the desired picture (or
tap on View in the task bar). This opens a new window showing the
picture.
• Tap Menu and Edit.
• Tap Menu again and select Crop.
• As instructed, drag a rectangle on the picture representing what the
final image should be like, then tap inside the rectangle to complete
the crop operation. If you’re not happy with the result, you can
always come back to the initial image by selecting Menu and
Revert to Saved.
• Tap OK to save the picture.
Auto-correcting a Picture
• With the “My Pictures” folder open, tap on the desired picture (or
tap on View in the task bar). This opens a new window showing the
picture.
• Tap Menu and Edit.
• Tap Menu again and select Auto Correct. This refines the picture’s
brightness, contrast and colors.
• Tap OK to save the picture.
Deleting a Picture
• With the “My Pictures” folder open, tap and hold the desired picture.
20
• Select Delete in the context‐sensitive menu.
• Tap Yes to confirm file deletion.
Changing Picture Settings
• Press the Windows key and tap Pictures & Videos. This opens the
“My Pictures” folder.
• Tap Camera to turn on the camera. Wait a couple of seconds until
the center of the window displays the viewfinder of the camera.
• Tap on the screen to re‐activate the task bar, tap Menu, then
Resolution. Choose one of the dimensions available ( expressed in
pixels). The resolution setting impacts the quality and size of the
picture you take.
• Tap Menu, then Mode. Choose between Normal (one picture
taken), Burst (five pictures taken at a one‐second interval once you
have pressed Enter) and Timer (picture taken 5 seconds after
pressing Enter).
Making a Video Setting the Duration of a Video Film
• Press the Windows key and tap Pictures & Videos. This opens the
“My Pictures” folder in which you can see the list of existing images
and videos.
• Tap Menu, Tools and then Options.
• Tap on the Video tab.
• The audio track may, or may not be included in your video files. Clear
or check the Include Audio.. option as needed.
• Tap within the Time limit for videos. field and select one of the
options below:
– No limit: Choose this option to be able to film a video
over an unlimited period of time.
– 15 seconds: Choose this option to limit the duration of
every video you’ll film to 15 seconds.
– 30 seconds: Choose this option to limit the duration of
every video you’ll film to 30 seconds.
• Tap OK to accept the changes and close the Options window.
Starting a Video
• Tap Camera to turn on the camera. Wait a couple of seconds until
the center of the window displays the viewfinder of the camera.
• Tap anywhere on the screen to make the task bar visible at the
bottom of the screen
21
• When you are ready to film, tap Menu and then Video.
• Press the Enter button to start filming.
Ending a Video
• Depending on the video settings, the video camera will stop filming
as explained below:
– With a preset time limit (15 or 30 seconds), the video
camera will stop filming automatically and close the
video file after this time has elapsed. A down counter
under the viewfinder will keep you informed of the
remaining time as you film.
– With no time limit, the video camera will film
indefinitely. A counter under the viewfinder will tell you
the current duration of the video. To stop filming and
close the video file, press the Enter button again.
• At the end of the video shooting, the viewfinder freezes while the
end of the video is being processed.
• Again, tap anywhere on the screen to make the task bar visible at
the bottom of the screen and then tap OK to turn off the camera
and close the window. The video file you have created is now listed
in the “My Pictures” folder.
Playing Back a Video
• With the “My Pictures” folder open, tap on the desired video file.
This will automatically launch the Windows Media player.
• Tap
to close Windows Media player and return to the “My
Pictures” folder.
Renaming a Video
• With the “My Pictures” folder open, select the desired video file
using the Scroll button.
• Tap Menu, Tools and then Properties.
• Rename the file and tap OK.
Deleting a Video
• With the “My Pictures” folder open, tap and hold the desired video
file.
• Select Delete in the context‐sensitive menu.
• Tap Yes to confirm file deletion.
22
E-Compass Calibration
• Press on the Windows key.
• Scroll down until you see the Compass icon.
• Tap on the Compass icon to open the Compass utility.
• Tap on the Calibration tab.
• Put the receiver down on a table to give it a horizontal position (see
picture [1] below).
• Tap on the Start button located in the task bar to start the
calibration process.
First horizontal calibration is ready to go.
• Slowly rotate the receiver by a couple of turns while keeping it
horizontal (see picture [1] below).
Wait until the receiver indicates that horizontal calibration is
complete and prompts you to start vertical calibration
( “Ready” displayed underneath the Vertical calibration
button).
• Take the receiver in your hands (see picture [2] below), put it in
vertical position then slowly rotate it by a couple of turns, in the
vertical plane. Then gently put it back down on the table.
• Wait until calibration is complete before proceeding.
Platform Specifications
23
GNSS
Characteristics
20 channels
• GPS L1 C/A
• SBAS: WAAS/EGNOS/MSAS
• External antenna connector
• NMEA Output
Accuracy
Specifications
All specified values are horizontal RMS, handheld accuracy
performance achieved in good conditions (open sky) with PDOP
< 3 and more than seven satellites in view.
• Real‐time SBAS: < 2 m typical
• Post‐processed: < 50 cm typical
Processor
• ARM9™
• Clock frequency: 600 MHz
Operating System
• Microsoft Windows Embedded Hand Held.
• Installed language at delivery: English, French, Spanish,
German, Portuguese, Italian, Simplified & Traditional
Chinese, Greek, Japanese or Korean. Installed OS language
cannot be changed once the product has been shipped in a
given language.
• Software package includes:
– Internet Explorer®
– Microsoft Office Mobile
– ActiveSync®
– Transcriber (handwriting recognition)
Communication Cellular:
• Built‐in cell modem
• Bands: Depending on MobileMapper 20 P/N and detected
network:
‐ P/N 802168‐00 (EU): 3G WCDMA: 900 and 2100 MHz
2G GSM: 850, 900 and 1800 MHz
‐ P/N 802168‐10 (US): 3G WCDMA: 850 and 900 MHz
2G GSM: 850, 900, 1800 and 1900 MHz
Bluetooth: 2.1 with EDR
WiFi: Integrated
Interface: USB
24
Physical
Characteristics
User Interface
• Receiver size: 169 x 88 x 25 mm
• Receiver weight, alone: 310 g
• Receiver weight (batteries included): 380 g
Keyboard:
• Alphanumeric virtual keyboard
• Four‐direction Scroll and Enter button, Zoom In/Out keys +
context‐sensitive keys
• Illuminated keyboard with touch screen
• Virtual keyboard
Display:
• Color TFT, VGA, high‐resolution display, sunlight readable,
with touch screen, LED backlight
• Size: 3.5”
• Colors: 262 k
Memory
Environmental
Characteristics
Power
Requirements
Multimedia &
Sensors
Software Options
• 256‐MB SDRAM
•
512‐MB NAND Flash (non‐volatile)
•
Micro SDHC™ memory card (up to 32 GB)
•
Operating temperature: ‐10° to +60°C (14 to 140°F)
•
•
Storage temperature: ‐30° to +70°C (‐13 to 158°F)
Humidity: 95% non condensing
•
Waterproofness: IP54
•
Free drop: 1.2 m to concrete
•
•
Battery life: > 20 hours @ 20 ºC, with GPS on, Bluetooth
and WiFi disabled, screen backlight used at minimum
level 20% of the time.
Charging time: 4 hours
•
Removable battery
•
3‐ Megapixel camera
•
•
E‐Compass
G‐Sensor
•
Speaker
•
Microphone
•
Spectra Precision MobileMapper Field and Office software
25
Standard
Accessories
26
•
Post‐processing
•
ESRI ArcPad software bundle (USA only)
•
Stylus
•
•
Hand strap
Universal AC adapter
•
USB cable.
Index
Lock keypad 6
Long time battery storage 14
Main Battery Low 14
Accessories 26
Main Battery Very Low 14
Adjusting backlight 5, 6, 16, 17, 18
Memory 25
Alignment 2
Microphone 9
Mini‐USB 10
Battery compartment 10
Modem (internal) 24
Battery life 25
Battery status icon 13
Opening battery door 1
Bluetooth 24
Operating system 2, 24
Burst 20
OPP (Object Push Profile) 24
Calibration (screen) 2
PDOP 11
Camera 18
Play back video 21
Camera lens 9
POGO cable 14
Camera settings 20
Power modes 14
Processor 24
Delete picture 20
Delete video file 22
Rename picture 19
Display screen 25
Rename video file 21
Reset 12 Resolution
Earpiece 9
Environmental characteristics 25
External antenna 9
External antenna input 9
GNSS reception characteristics 24
GNSS settings 11 GNSS
status 11
GNSS Toolbox 11
20
SBAS 11 Screen alignment 2
Sensors 25
Standby 21
Start shooting video 21 Stop
shooting video 21
Suspend mode 4, 13
Time limit (video) 20
Timer 20 Tracking
mode 11
Holding the receiver properly 7
GPS antenna (built‐in) 9
Universal AC adapter 1
Inserting battery 1
USB 10
VVideo (duration setting) 20
Keyboard 25
VGA 8
®
MobileMapper
20
Getting Started Guide
FCC Regulations
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
•
This device may not cause harmful interference
•
This device must accept any interference
received, including interference that may cause
undesired operation.
•
This device has been tested and found to comply
with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
•
‐Reorient or relocate the receiving antenna.
•
‐Increase the separation between the
equipment and receiver.
•
‐Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
•
‐Consult the dealer or an experienced radio/TV
technician for help.
•
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user‘s authority to
operate the equipment.
FCC RF Exposure Information and Statement:
The SAR limit of USA (FCC) is 1.6 W/kg averaged over
one gram oftissue.Device types: MobileMapper 20
(FCC ID: NZI802168) has also been tested against
this SAR limit. The highest SAR value reported under
this standard during product certification for use at
the ear is 0.285W/kg and on the body is 0.689W/kg.
•
•
•
•
•
•
•
Le présent appareil est conforme aux
CNR d'Industrie Canada applicables
aux appareils radio exempts de
licence. L'exploitation est autorisée
aux deux conditions suivantes:
l'appareil ne doit pas produire de
brouillage, et
l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi,
même si le brouillage est susceptible
d'en
This Class B digital apparatus
complies with Canadian ICES‐003.
Cet appareil numérique de la classe B
est conforme à la norme NMB‐003 du
Canada.
For SAR test,Body worn mode test
distance is 10mm.
IC Notice
•
This device complies with Industry Canada
license‐exempt RSS standard(s). Operation is
subject to the following two conditions:
•
this device may not cause interference, and
•
this device must accept any interference,
including interference that may cause undesired
operation of the device.
Contact Information:
AMERICAS
EUROPE, MIDDLE EAST & AFRICA
ASIA‐PACIFIC
Spectra Precision Division
103 68 Westmoor Drive, Suite
Westminster, CO 80021,
USA
Spectra Precision Division
Rue Thomas Edison
ZAC de la Fleuriaye, BP 60433
44474 Carquefou Cedex, FRANCE
Spectra Precision Division
80 Marine Parade Road
#22‐06, Parkway Parade
Singapore 449269, Singapore
www.spectraprecision.com
©201 3 Trimble Navigation Limited. All rights reserved. Spectra Precision is a Division of Trimble Navigation Limited. Spectra Precision and the Spectra
Precision logo are trademarks of Trimble Navigation Limited or its subsidiaries. P/N 6316
75‐01 A.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : jiaxing.ye
Create Date                     : 2014:01:14 18:57:33+08:00
Modify Date                     : 2014:01:14 18:57:33+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 9.5.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - NZI802168_User manual 09.docx
Creator                         : jiaxing.ye
Document ID                     : uuid:42927463-1fe0-4f6d-8dde-39a5cf219aef
Instance ID                     : uuid:30ba7774-7d1c-4a23-92f3-421b0f382cfb
Page Count                      : 34

EXIF Metadata provided by EXIF.tools