TSC Auto ID Technology 2012001 WiFi Module User Manual WIFI EM01 UserMan 20120723

TSC Auto ID Technology Co., Ltd. WiFi Module WIFI EM01 UserMan 20120723

(WIFI-EM01) UserMan.pdf_20120723

WIFI MODULE INSTALLATION GUIDE WIFI-EM01, WIFI-EM101 Installing the WiFi Device to the Printer Please follow the steps below to install the WiFi device. 1. Turn off the printer power. 2. Plug in the WiFi device into the RS-232 port. 3. Fasten the device by two screws. Setting the Communication Settings For industrial printer, the RS-232 communication parameters can be configured from the LCD control panel by the following procedures. 1. Turn on the printer power. 2. Enter the main menu. 3. Select Serial Comm. Option. 4. Make sure the communication parameters are set to 115200 bps baud rate, None parity, 8 data bits, 1 stop bit. For desktop printer models, the RS-232 communication parameters can be setup following command Syntax: SET COM1 115, N, 8, 1 P/N: 39-0000-00LF Baud Rate -- Parity -- Data Bite -- Stop Bits -- Exit Serial Comm.WiFi device ScrewLED indicator Note: This RS-232 interface of WiFi device is used with the printer only.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. RF exposure warning This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instructions and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. SAR standard Value: 1.6 W/Kg, Maximal Measure: 0.487 W/kg Canada, Industry Canada (IC) Notices This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has been evaluated for and shown compliant with the IC Specific Absorption Rate (“SAR＂) limits when installed in specific host products operated in portable exposure conditions. Canada, avis d'Industry Canada (IC) Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement. Informations concernant l'exposition aux fréquences radio (RF) La puissance de sortie émise par l＇appareil de sans fil Dell est inférieure à la limite d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez l＇appareil de sans fil Dell de façon à minimiser les contacts humains lors du fonctionnement normal. CepériphériqueaétéévaluéetdémontréconformeauxlimitesSAR(SpecificAbsorptionRate–Tauxd'absorptionspécifique)d'IClorsqu'ilestinstallédansdesproduitshôtesparticuliersquifonctionnentdansdesconditionsd'expositionàdesappareilsportables.

Navigation menu