Tait TBBH5A Base Station Transceiver User Manual TB7100 Installation and Operation Manual

Tait Limited Base Station Transceiver TB7100 Installation and Operation Manual

Exhibit D Users Manual per 2 1033 c3

 TB7100 base stationInstallation andOperation ManualMBB-00001-02Issue 2December 2005
 2TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Tait Contact InformationTait Radio CommunicationsCorporate Head OfficeTait Electronics LtdP.O. Box 1645ChristchurchNew ZealandFor the address and telephone number of regional offices, refer to the TaitWorld website:Website: http://www.taitworld.comTechnical SupportFor assistance with specific technical issues, contact Technical Support:E-mail: support@taitworld.comWebsite: http://support.taitworld.comTo our European customers:Tait Electronics Limited is an environmentally responsible company which supports waste minimization and material recovery. The European Union’s Waste Electrical and Electronic Equipment Directive requires that this product be disposed of separately from the general waste stream when its service life is over. Please be environmentally responsible and dispose through the original supplier, your local municipal waste “separate collection” service, or contact Tait Electronics Limited.
 TB7100 Installation and Operation Manual 3© Tait Electronics Limited May 2005ContentsPreface  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Scope of Manual  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Enquiries and Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Updates of Manual and Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Associated Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Publication Record  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  111.1 Frequency Bands  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121.2 RF Output Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121.3 Power Supply Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131.4 Mechanical Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131.5 Product Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 Mechanical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  152.1 Tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162.2 UI Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162.3 Receiver Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172.4 Transmitter Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182.5 SI Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192.6 AC Power Supply Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  213.1 Receiver Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233.1.1 RF Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233.1.2 Digital Baseband Processing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243.1.3 Audio Processing and Signalling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253.2 Transmitter Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263.2.1 Audio Processing and Signalling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263.2.2 Frequency Synthesizer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273.2.3 RF Power Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303.3 User Interface Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323.4 System Interface Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353.4.1 Internal Power Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373.4.2 Serial Data  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383.4.3 General Purpose IO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383.4.4 Receiver Audio Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383.4.5 Tone On Idle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383.4.6 Transmitter Audio Processing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
 4TB7100 Installation and Operation Manual© Tait Electronics Limited May 20053.4.7 Opto Isolated Keying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393.4.8 Relay Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393.4.9 Fan Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393.4.10 RSSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393.4.11 Receiver Gate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393.4.12 Receiver Inhibit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393.5 Fan Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  414.1 Personal Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414.1.1 Lethal Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414.1.2 Explosive Environments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424.1.3 Proximity to RF Transmissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424.1.4 High Temperatures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424.2 Equipment Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424.2.1 ESD Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424.2.2 Antenna Load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434.2.3 Equipment Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434.2.4 Installation and Servicing Personnel . . . . . . . . . . . . . . . . . . . . . . . . . . 434.3 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434.3.1 Distress Frequencies  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434.3.2 FCC Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444.3.3 Unauthorised Modifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444.3.4 Health, Safety and Electromagnetic Compatibility in Europe. . . . . . . . 444.4 Environmental Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454.4.1 Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454.4.2 Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454.4.3 Dust and Dirt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454.5 Grounding and Lightning Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454.5.1 Electrical Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454.5.2 Lightning Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454.6 Recommended Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464.7 Ventilation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464.7.1 Cabinet and Rack Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464.8 Installing the Base Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 494.8.1 Unpacking the Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 494.8.2 Identifying the Mechanical Configuration . . . . . . . . . . . . . . . . . . . . . 494.8.3 Power Supply Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 504.8.4 Setting the AC Mains Input Voltage  . . . . . . . . . . . . . . . . . . . . . . . . . 504.8.5 Mounting the Base Station  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514.8.6 Cabling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524.8.7 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 525 Replacing Modules  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  535.1 Removing the Base Station and Opening the Tray. . . . . . . . . . . . . . . . . . . . . . . 545.2 Replacing the UI Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 555.3 Replacing the Receiver Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565.4 Replacing the Transmitter Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
 TB7100 Installation and Operation Manual 5© Tait Electronics Limited May 20055.5 Replacing the SI Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585.6 Replacing the Transmitter and Receiver Fans  . . . . . . . . . . . . . . . . . . . . . . . . . . 595.7 Replacing the Fan Power Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 605.8 Replacing the Temperature Sensor Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 605.9 Replacing the AC Power Supply Unit, Fan and Filter Module . . . . . . . . . . . . . .615.10 Replacing the Speaker  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625.11 Final Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 636 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  656.1 External Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 666.2 Internal Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 716.2.1 Transmitter and Receiver Connectors . . . . . . . . . . . . . . . . . . . . . . . . 716.2.2 SI Board Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 736.2.3 UI Board Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 757 Preparation for Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  777.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 777.2 Mode of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 777.3 Line-controlled Base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 787.3.1 Test Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 787.3.2 Test Equipment Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 797.3.3 Link Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 807.3.4 Applying Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 817.3.5 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 827.3.6 Receiver Audio Level Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . 837.3.7 Receiver Functional Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 847.3.8 Transmitter Audio Level Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 857.3.9 Transmitter Functional Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .867.4 Talk Through Repeater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 887.4.1 Test Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 887.4.2 Test Equipment Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 897.4.3 Link Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 897.4.4 Applying Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 907.4.5 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 907.4.6 Audio Level Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 917.4.7 Talk Through Repeater Functional Testing . . . . . . . . . . . . . . . . . . . . 917.4.8 Alternate Talk Through Repeater Configuration  . . . . . . . . . . . . . . . . 927.5 RF Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 937.5.1 Test Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 937.5.2 Test Equipment Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 947.5.3 Link Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 947.5.4 Applying Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 957.5.5 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 967.5.6 Audio Level Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 967.5.7 Programming for FFSK Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . 967.5.8 Programming for THSD Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 987.5.9 Verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
 6TB7100 Installation and Operation Manual© Tait Electronics Limited May 20057.6 Data Repeater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1017.6.1 Link Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1027.6.2 Applying Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1037.6.3 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1037.6.4 Audio Level Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1037.6.5 Data Repeater Functional Testing . . . . . . . . . . . . . . . . . . . . . . . . . . 1047.7 TaitNet Trunking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1047.8 Programmable Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1057.8.1 Connecting to the PC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1057.8.2 TB7100 Programming Application  . . . . . . . . . . . . . . . . . . . . . . . . . 1057.8.3 Mandatory Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1077.8.4 User-defined Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1087.8.5 Recommended Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1127.8.6 Function Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1137.9 Additional Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1157.10 Adding Subaudible Signalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1157.10.1 Enabling Subaudible Signalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1157.10.2 Testing Subaudible Signalling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1167.10.3 Multiple Subaudible Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1177.11 Soft Off (Tx Tail Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1187.11.1 Link Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1187.12 Tone On Idle (TOI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1187.12.1 Link Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1197.13 Fan Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1207.13.1 Link Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1207.14 Channel ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1227.14.1 Link Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1227.15 Relay Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1237.15.1 Link Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1237.16 Channel Increment and Decrement by Function Keys . . . . . . . . . . . . . . . . . . . 1237.17 Carrier Wave Identification (CWID). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1247.17.1 Station ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1247.17.2 Station ID 2/Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1247.17.3 Tone Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1247.17.4 ID Repeat Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1247.17.5 Speed (Words per Minute) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1247.17.6 Wait Period after Loss of COR/COS/CTCSS Input Before IDing. . 1247.17.7 Transmit Key-Up Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1247.17.8 Transmit Time Out Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1257.17.9 Transmit PTT Drop Out Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1257.17.10Output Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1258 Maintenance Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129Directive 1999/5/EC Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . .141
 TB7100 Installation and Operation Manual 7© Tait Electronics Limited December 2005PrefaceScope of ManualWelcome to the TB7100 Installation and Operation Manual. This manual provides information on installing and operating the TB7100 base station. Also included in this manual are a high-level circuit description, a functional description and a maintenance guide.Enquiries and CommentsIf you have any enquiries regarding this manual, or any comments, suggestions and notifications of errors, please contact Technical Support (refer to “Tait Contact Information” on page 2).Updates of Manual and EquipmentIn the interests of improving the performance, reliability or servicing of the equipment, Tait Electronics Limited reserves the right to update the equipment or this manual or both without prior notice.CopyrightAll information contained in this manual is the property of Tait Electronics Limited. All rights are reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated, stored, or reduced to any electronic medium or machine-readable form, without prior written permission from Tait Electronics Limited.DisclaimerThere are no warranties extended or granted by this manual. Tait Electronics Limited accepts no responsibility for damage arising from use of the information contained in the manual or of the equipment and software it describes. It is the responsibility of the user to ensure that use of such information, equipment and software complies with the laws, rules and regulations of the applicable jurisdictions.
 8TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Document Conventions“File > Open” means “click File on the menu bar, then click Open on the list of commands that pops up”. “Channel Setup > Channels > Detailed” means “in the navigation pane find the Channel Setup group, and select Channels from it, on the Channels page select the Detailed tab”.Within this manual, four types of alerts are given to the reader: Warning, Caution, Important and Note. The following paragraphs illustrate each type of alert and its associated symbol.Warning!! This alert is used when there is a potential risk of death or serious injury.Caution This alert is used when there is a risk of minor or moderate injury to people.Important This alert is used to warn about the risk of equipment dam-age or malfunction.Note This alert is used to highlight information that is required to ensure procedures are performed correctly.Associated DocumentationThe following associated documentation is available for this product:■MBB-00002-xx TB7100 Specifications Manual■MBB-00003-xx TB7100 Installation Guide■MBB-00005-xx TB7100 Service Manual■MBA-00013-xx TBA0STU/TBA0STP Calibration and Test Unit Operation ManualThe characters xx represent the issue number of the documentation.All available documentation is provided on the CD (406-00047-xx) supplied with the base station. Updates may also be published on the Tait support website.Technical notes are published from time to time to describe applications for Tait products, to provide technical details not included in manuals, and to offer solutions for any problems that arise.
 TB7100 Installation and Operation Manual 9© Tait Electronics Limited December 2005Publication RecordIssue Publication Date Description1 May 2005 First release2 December 2005 Internal AC power supply, A4 and D1 bands added.
 10 TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005
 TB7100 Installation and Operation Manual Introduction 11© Tait Electronics Limited December 20051IntroductionThe TB7100 is a software and hardware link-configured base station which is designed for operation in a large variety of standard frequency ranges. It makes extensive use of digital and DSP technology. Many operating parameters such as channel spacing, audio bandwidth and signalling are controlled by software.This manual includes the information required for installing and operating the base station.This section describes the different options available for:■frequency bands■RF output power■power supply■mechanical configurations■product codesFor specifications, refer to the specifications manual or the area on the TaitWorld website reserved for TB7100 products.Figure 1.1 TB7100 base stationsConfiguration with provision for internal AC power supply*Configuration without provision for internal AC power supply* *cover removed
 12 Introduction TB7100 Installation and Operation Manual© Tait Electronics Limited December 20051.1 Frequency BandsThe base station is available in the following frequency bands:■66 to 88MHz (A4)■136 to 174MHz (B1)■216 to 266 MHz (D1)■400 to 470MHz (H5)■450 to 530MHz (H6)■450 to 520MHz (H7)The RF band of the base station is implemented by the frequency band of the transmitter and receiver modules. 1.2 RF Output PowerThe base station is available with 25W and 50W/40W RF output power. The RF output power options are implemented by different transmitter and receiver modules.The 25W base station is available in the following frequency bands:■A4■B1■D1■H5■H6The 50W/40W base station is available in the following frequency bands:■B1 (50W)■H5 (40W)■H7 (40W)
 TB7100 Installation and Operation Manual Introduction 13© Tait Electronics Limited December 20051.3 Power Supply OptionsThe base station is available with or without an internal AC power supply.All base stations have an external DC input power connector which is used as main power supply when no internal AC power supply is fitted.When the internal AC power supply is fitted, the DC input can be used as a DC backup power option. In case of AC mains failure the base station will automatically and seamlessly switch to DC power input.If no internal AC power supply is fitted, an external Tait T809-10-87xx power supply can be used to supply the DC voltage required.Warning!! The internal AC power supply unit contains voltages that may be lethal. Refer to the ratings label on the rear of the base station. The internal AC power supply contains no user-servicable parts.Important Wrong mains voltage! Before connecting to the AC power connector, ensure that the internal 115V/230V voltage mains selector switch is set to the correct mains voltage.1.4 Mechanical ConfigurationsThe base station is available in two different mechanical configurations—with or without provision for an internal AC power supply unit.The mechanical configuration with provision for an internal AC power supply has the following distinguishing features:■larger air intake on the right-hand side of the front panel■provision for AC connector on the left-hand side of the rear panel (refer to Figure 1.1 on page 11)■ground point on the right-hand side of the rear panel rather than on the left-hand side■different SI board and internal cables.The mechanical configuration without provision for an internal AC power supply unit cannot be upgraded with an internal AC power supply unit.The product codes of the base station (see below) do not distinguish between the mechanical configurations.
 14 Introduction TB7100 Installation and Operation Manual© Tait Electronics Limited December 20051.5 Product CodesThis section describes the product codes used to identify products of the TB7100 base station product line.The product codes of the TB7100 base station product line has the format:TBBaabb-cde-ffwhere:■aa identifies the frequency band of the receiver:A4=66 to 88MHz, B1=136 to 174MHz, D1=216 to 266 MHz, H5=400 to 470MHz, H6=450 to 530MHz, H7=450 to 520MHz■bb identifies the frequency band of the transmitter:A4=66 to 88MHz, B1=136 to 174MHz, D1=216 to 266 MHz, H5=400 to 470MHz, H6=450 to 530MHz, H7=450 to 520MHz■c identifies the RF output power and digital architecture:A=25W, level-1 digital architectureB=35W to 50W, level-1 digital architectureC=25W, level-2 digital architectureD=35W to 50W, level-2 digital architectureE=25W, level-3 digital architectureF=35W to 50W, level-3 digital architecture■d identifies the power supply option:0=DC only1=internal AC power supply unit, factory preset to 115VAC2=internal AC power supply unit, factory preset to 230VAC■e identifies the AC power cable:1 = Australia/New Zealand2 = United Kingdom3 = Europe4 = USA■ff identifies base station options:00=no options
 TB7100 Installation and Operation Manual Mechanical Description 15© Tait Electronics Limited December 20052 Mechanical DescriptionOverview The base station consists of the following main modules:■tray b■UI board (user interface) d■receiver module h■transmitter module i■SI board (system interface) 1)■internal AC power supply unit 1@ (if fitted).All modules and boards are mounted from above into the 1U tray b. The modules are secured by screws or clips into standoffs on the tray chassis, and are easily removed for replacement.The base station includes two cooling fans f and a fan duct e in front of the receiver and transmitter modules, a speaker c mounted behind the front panel, a fan power board g mounted on the fan duct, and a temperature sensor board j mounted on the heatsink of the transmitter module i.If the internal AC power supply unit 1@ is fitted, the base station includes an additional fan 1# and an AC filter module 1!.The modules and components are interconnected by looms and cables.Figure 2.1 Parts of the base station (configuration with internal AC power supply unit shown)1!gi1)bcdfehj1@1#
 16 Mechanical Description TB7100 Installation and Operation Manual© Tait Electronics Limited December 20052.1 TrayThe 1U tray consists of a mild steel folded chassis and a flat cover (not shown) which is fastened to the chassis with 15 Torx T10 screws. The tray can be fitted into a standard 19 inch rack or cabinet using the two rack mounting brackets.The front panel has holes to accommodate the controls and the microphone/programming connector of the UI board. The rear panel has holes to accommodate the connectors and the fuse holder of the SI board, the antenna connectors, and a ground terminal.For more information on the connections, refer to “Connections” on page 65.2.2 UI BoardThe UI board is mounted behind the front panel with three Torx T10 screws c and two spring clips D. The UI board is connected to the transmitter and receiver modules via the two Micro-MaTch connectors e and the two UI cables (not shown). The UI board also has a speaker connector b.A volume knob is fitted to the shaft of the volume-control potentiometer.Figure 2.2 UI boardedcbCables not shown.
 TB7100 Installation and Operation Manual Mechanical Description 17© Tait Electronics Limited December 20052.3 Receiver ModuleThe receiver module is mounted in the front left of the tray with five Torx T10 screws g.The receiver module is a printed circuit board in SMT design with components on the top and bottom sides. A digital board is reflow-soldered to the receiver. Most components are shielded by metal cans.There are different boards for each frequency band and each RF output power configuration.The RF b, DC power c, auxiliary d, and user interface f connectors are located on the bottom side of the board. The internal options connector e and a factory connector (not shown) for factory use are located on the top side of the board.For compliance reasons, there are different variants of the receiver module for use in the 25W and 50W/40W base stations. The 25W version has a white DC power connector C and the 50W/40W version has a black DC power connector.For more information on the connectors, refer to “Connections” on page 65.Figure 2.3 Receiver moduleggfbcdge
 18 Mechanical Description TB7100 Installation and Operation Manual© Tait Electronics Limited December 20052.4 Transmitter ModuleThe transmitter module consisting of a transmitter board f mounted on a purpose-designed heatsink 1) is mounted in the left rear of the tray with four Torx T10 screws (not shown).The transmitter board is a printed circuit board in SMT design with components on the top and bottom sides. A digital board is reflow-soldered to the board. Most components are shielded by metal cans. There are different boards for each frequency band and each RF output power configuration.The RF b, DC power c, auxiliary d, and user interface f connectors are located on the bottom side of the board. The internal options connector e and a factory connector (not shown) for factory use are located on the top side of the board.The 50W/40W version has a black DC power connector C and the 25W version has a white DC power connector. For more information on the connectors, refer to “Connections” on page 65.The board f is mounted to the heatsink 1) with seven Torx T10 screws fand g.An L-shaped gap pad i and (with the 50W/40W version) a rectangular gap pad j are fitted between the board f and the heatsink 1) to improve heat transfer.Figure 2.4 Transmitter moduleghgcf1)Dbeji
 TB7100 Installation and Operation Manual Mechanical Description 19© Tait Electronics Limited December 20052.5 SI BoardThe SI board is mounted in the rear right of the tray with two Torx T10 screws 1), one Pozidriv screw j, and two spring clips 1!. The SI board has the following external connectors:■13.8V DC power connector (labelled 12V DC) b■system connector (labelled SYSTEM) c■serial data connector (labelled IOIOI) D.The SI board has the following internal connectors:■two system interface connectors e (to transmitter and receiver)■one DC input connector h, if fitted (from internal AC power supply)■one DC output connector i (to transmitter and receiver)■fan control connector f (to fan power board on fan duct)■temperature control connector g (to temperature sensor on transmitter heatsink).For more information on the connectors, refer to “Connections” on page 65.Figure 2.5 SI boardgibc d1) 1)j1!1! efh
 20 Mechanical Description TB7100 Installation and Operation Manual© Tait Electronics Limited December 20052.6 AC Power Supply UnitThe base station may be fitted with an internal AC power supply unit f, an AC filter module d, and an additional fan g.The AC filter module has a standard AC connector that fits into a provision on the rear of the tray. The AC filter module slides into securing tabs on the tray floor and is held in place by the AC power supply unit.Note Mechanical configurations without the provision for a standard AC connector cannot be upgraded with the internal AC power supply unit.The AC power supply unit is held in place by two screws e. The fan is attached to the AC power supply unit by two screws h.The AC power supply unit is connected to the AC filter module via a cable connector (not shown).The DC output of the AC power supply unit is connected to the SI board b. The AC power supply unit also has a cable to provide a mains failure signal to the SI board c. In case of a mains failure, this signal will cause the power circuitry on the SI board to switch to DC external input.Figure 2.6 AC power supply unit, filter module and fanhe dfebcg
 TB7100 Installation and Operation Manual Functional Description 21© Tait Electronics Limited December 20053 Functional DescriptionThis section describes some principles of the base station operation.Figure 3.1 shows the high-level block diagram of the base station.Figure 3.1 Base station high-level block diagramDC InputConnector SystemConnector Serial DataConnector AC InputConnectorRxConnectorTx/AntConnectorGroundPointTransmitterModuleReceiverModuleUI BoardACPower SupplyUnitFanFanFanFan PowerBoardSpeakerTemperatureSensorProg/MicConnectorReceiver/SIInternal powerRFTransmitter/SIInternal powerRFUI/ReceiverInternal powerUI/TransmitterInternal powerAC Input FilterModule115V/230VSelectorSwitchSI BoardFuseMains fail signal
 22 Functional Description TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005The block diagram illustrates the main inputs and outputs for power, RF and control signals, as well as the interconnection between modules:■program data and audio from the PROG/MIC socket on the UI board to and from the transmitter and receiver modules■audio and signalling from the SYSTEM connector to and from the transmitter and receiver modules■RS-232 data from the serial data connector (IOIOI) to and from the transmitter and receiver modules■fan power and control from the SI board■power distribution from the AC and DC power input connectors to the transmitter and receiver modules, and from the receiver module to the UI board.The circuitry of the individual modules that make up the base station is described in more detail in the following sections.Frequency Bands and Sub-bands The circuitry of the transmitter and receiver modules is similar for all frequency bands and is therefore covered by a single description in this manual. Where the circuitry differs between bands, separate descriptions are provided for each frequency band. For more information on frequency bands, refer to the specifications manual.RS-232 Signals External data communications all occur directly between the connected computer (or other electrical equipment) and the transmitter and receiver modules over the RS-232 serial lines.Fan Signals The power and ground signals for the fans are routed from the SI board to the fans behind the front panel. These signals are electrically isolated from all other system signals to ensure fan noise is not transferred to other sensitive system components.If there is a fault in the fan circuitry, the transmitter module is protected from overheating by its internal foldback circuitry.Speaker Signal Received audio is sent from the receiver module to the UI board. The volume is controlled by the volume potentiometer on the UI board. The audio signal is routed through the UI board to the speaker for monitoring purposes.Power and Ground The SI board provides power to the transmitter and receiver modules. The receiver modules provides power to the UI board.
 TB7100 Installation and Operation Manual Functional Description 23© Tait Electronics Limited December 20053.1 Receiver OperationParts of Receiver Board The main circuit parts of the receiver modules are:■receiver■frequency synthesizer■CODEC (coder-decoder) and audio circuitry■power supply■interface circuitrySoftware plays a prominent role in the functioning of the radio. When describing the operation of the radio the software must be included with the above. This is considered further below.These functional parts are described in detail below.3.1.1 RF HardwareFront End Circuitryand First IF The front-end hardware amplifies and image filters the received RF spectrum, then down-converts the desired channel frequency to a first intermediate frequency IF1 of 45.1MHz (UHF) or 21.4MHz (VHF) where coarse channel filtering is performed. The first LO (local oscillator) signal is obtained from the frequency synthesizer and is injected on the low side of the desired channel frequency for all bands except A4. When receiving the modulation to the frequency synthesizer is muted. The output of the first IF (intermediate frequency) stage is then down-converted using an image-reject mixer to a low IF of 64kHz.Figure 3.2 Receiver high-level block diagramIF:UHF: 45.1 MHzVHF: 21.4 MHzDigitaldown-converterSquelchFrontend1stIFChannelLPFChannelLPFRSSISecond LOUHF: 90.328 MHzVHF: 42.928 MHzFMDemodQuadDemodRXAGCAnalogue-to-digital conversion2nd IF:64 kHzAudiofilteringDe-emphasisOptionalprocessingData and signallingdecodersSidetonesSystem Interfaceor User InterfacePhaselocked toTCXOLPFANTMag.PLLLoopfilterLoopfilterFrequencycontrolTriple-pointEqualisationTCXO:13.000 MHzVCOVCXOCUSTOM-LOGICBLOCKHARDWARE BLOCKDigital-to-analogue conversionKEYNOTES(1) Noise blanker not shownDSPBLOCK
 24 Functional Description TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Quadrature Demodulator The LO for the image-reject mixer (quadrature demodulator) is synthesized and uses the TCXO (temperature-compensated crystal oscillator) as a reference. This ensures good centring of the IF filters and more consistent group-delay performance. The quadrature demodulator device has an internal frequency division of 2 so the second LO operates at 2x(IF1 + 64kHz). The quadrature output from this mixer is fed to a pair of ADCs (analog-to-digital converters) with high dynamic range where it is oversampled at 256kHz and fed to the custom logic device.Automatic Gain Control The AGC (automatic gain control) is used to limit the maximum signal level applied to the image-reject mixer and ADCs in order to meet the requirements for intermodulation and selectivity performance. Hardware gain control is performed by a variable-gain amplifier within the quadrature demodulator device driven by a 10-bit DAC (digital-to-analog converter). Information about the signal level is obtained from the IQ (in-phase and quadrature) data output stream from the ADCs. The control loop is completed within custom logic. The AGC will begin to reduce gain when the combined signal power of the wanted signal and first adjacent channels is greater than about –70dBm. In the presence of a strong adjacent-channel signal it is therefore possible that the AGC may start acting when the wanted signal is well below –70dBm.3.1.2 Digital Baseband ProcessingCustom Logic The remainder of the receiver processing up to demodulation is performed by custom logic. The digitised quadrature signal from the RF hardware is digitally down-converted to a zero IF, and channel filtering is performed at base-band. Different filter shapes are possible to accommodate the various channel spacings and data requirements. These filters provide the bulk of adjacent channel selectivity for narrow-band operation. The filters have linear phase response so that good group-delay performance for data is achieved. The filters also decimate the sample rate down to 48kHz. Custom logic also performs demodulation, which is multiplexed along with AGC and amplitude data, and fed via a single synchronous serial port to the DSP. The stream is demultiplexed and the demodulation data used as an input for further audio processing.Noise Squelch The noise squelch process resides in the DSP. The noise content above and adjacent to the voice band is measured and compared with a preset threshold. When a wanted signal is present, out-of-band noise content is reduced and, if below the preset threshold, is indicated as a valid wanted signal.Received SignalStrength Indication Received signal strength is measured by a process resident in the DSP. This process obtains its input from the demodulator (value of RF signal magnitude) and from the AGC (value of present gain). With these two inputs and a calibration factor, the RF signal strength at the antenna can be accurately calculated.
 TB7100 Installation and Operation Manual Functional Description 25© Tait Electronics Limited December 2005Calibration The following items within the receiver path are calibrated in the Factory:■front-end tuning■AGC■noise squelch■RSSI (received signal strength indication)Information on the calibration of these items is given in the on-line help facility of the calibration application.3.1.3 Audio Processing and SignallingAudio Processing Raw demodulated data from the receiver is processed within the DSP. The sample rate at this point is 48kHz with signal bandwidth limited only by the IF filtering. Scaling (dependent on the bandwidth of the RF channel) is then applied to normalise the signal level for the remaining audio processing. The sample rate is decimated to 8kHz and bandpass audio filtering (0.3 to 3kHz) is applied. The base station takes the audio from the receiver mode at Tap R4 by default; this point has no de-emphasis. This tap point can be changed if required, for example, for trunking applications.Data and Signalling Decoders The data and signalling decoders obtain their signals from various points within the audio processing chain. The point used depends on the bandwidth of the decoders and whether de-emphasis is required. Several decoders may be active simultaneously.Side Tones Side tones are summed in at the end of the audio-processing chain. These are tones that provide some form of alert or give the user confidence an action has been performed. The confidence tones may be generated in the receiver. The side-tone level is a fixed proportion (in the order of –10dB) relative to full scale in the receive path. By default, all audible indicators are turned off.CODEC The combined audio and side-tone signal is converted to analog form by a 16-bit DAC with integral anti-alias filtering. This is followed by a programmable-gain amplifier with a range of 45dB in 1.5dB steps. The amplifier performs muting. The DAC is part of the same CODEC device (AD6521).Output to Speakers The output of the CODEC is fed to an audio power amplifier and to the UI board via a buffer amplifier. The output configuration of the audio power amplifier is balanced and drives an internal speaker. The power delivered to the speaker is limited by its impedance. The speaker has 16Ω impedance.
 26 Functional Description TB7100 Installation and Operation Manual© Tait Electronics Limited December 20053.2 Transmitter OperationParts of Transmitter Board The main circuit parts of the transmitter board are:■transmitter■frequency synthesizer■CODEC (coder-decoder) and audio circuitry■power supply■interface circuitrySoftware plays a prominent role in the functioning of the board. When describing the operation of the radio the software must be included with the above. This is considered further below.These functional parts are described in detail below.3.2.1 Audio Processing and SignallingMicrophone Input The input to the transmitter path begins at either the SI board or the PROG/MIC connector of the UI board. Only electret-type microphones are supported. The audio input is then applied to tap point T8 on the transmitter board (the tap point is user-selectable).Analog Processingof Microphone SignalThe CODEC (AD6521) performs microphone selection and amplification. The microphone amplifier consists of an amplifier with a fixed gain of 16dB followed by a programmable-gain amplifier with 0dB to 22dB gain. The amplified microphone signal is converted to a digital stream by a 16-bit ADC with integral anti-alias filtering (0.1 to 3.2kHz). The digital stream is transported to the DSP for further audio processing.Figure 3.3 Transmitter high-level block diagramAnalog-to-digital conversionLPFANTPLLLoopfilterLoopfilterFrequencycontrolTriple-pointEqualisationAudiofilteringPre-emphasisOptionalprocessingData and signallingencodersALC MicPGADir.Coup. Fin Drv/ExPwrCrtlRampcontrolTCXO:13.000 MHzVCOVCXOBiasCUSTOMLOGICBLOCKHARDWAREBLOCKHARDWARE BLOCKDigital-to-analog conversionKEYPROG/MIC connectorDSPBLOCKSYSTEM connectorTap point T8
 TB7100 Installation and Operation Manual Functional Description 27© Tait Electronics Limited December 2005Automatic Level Control The ALC (automatic level control) follows, and is used to effectively increase dynamic range by boosting the gain of the microphone pre-amplifier under quiet conditions and reducing the gain under noisy acoustic conditions. The ALC function resides in the DSP and controls the microphone programmable-gain amplifier in the CODEC. The ALC has a fast-attack (about 10ms) and slow-decay (up to 2s) characteristic. This characteristic ensures that the peak signal level is regulated near full scale to maximise dynamic range.DSP Audio Processing The output of the automatic level control provides the input to the DSP audio-processing chain at a sample rate of 8kHz. Optional processing such as encryption or companding is done first if applicable. Pre-emphasis, if required, is then applied. The pre-emphasised signal is hard limited to prevent over deviation, and filtered to remove high-frequency components. The sample rate is then interpolated up to 48kHz and scaled to be suitable for the frequency synthesizer.Data and Signalling Encoders The data and signalling encoders inject their signals into various points within the audio-processing chain. The injection point depends on the bandwidth of the encoders and whether pre-emphasis is required.3.2.2 Frequency SynthesizerMain Parts of Synthesizer The frequency synthesizer consists of two main parts:■FCL (frequency control loop)■RF PLL (phase-locked loop)The FCL and RF PLL are described briefly below. Note that patents are pending for several aspects of the synthesizer design.Frequency Control Loop The FCL consists of the following:■TCXO■mixer■loop filter■VCXO (voltage-controlled crystal oscillator)■frequency control blockThe FCL provides the reference frequency for the RF PLL. It generates a high-stability reference frequency that can be both modulated and offset in fine resolution steps.
 28 Functional Description TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005RF PLL The RF PLL consists of the following:■RF PLL device■loop filter■VCO (voltage-controlled oscillator)■VCO output switchThe RF PLL has fast-locking capability but coarse frequency resolution. The above combination of control loops creates improved frequency generation and acquisition capabilities.Operation ofControl Loop The RF PLL is a conventional integer-N design with frequency resolution of 25kHz. In transmit mode the loop locks to the transmit frequency.Initially, the VCO generates an unregulated frequency in the required range. This is fed to the PLL device (ADF4111) and divided down by a programmed ratio to approximately 25kHz. The reference frequency input from the FCL is also divided down to approximately 25kHz. The phase of the two signals is compared and the error translated into a DC voltage by a programmable charge pump and dual-bandwidth loop filter. This DC signal is used to control the VCO frequency and reduce the initial error. The loop eventually settles to a point that minimises the phase error between divided-down reference and VCO frequencies. The net result is that the loop locks to a programmed multiple of the reference frequency.The FCL generates an output of 13.012±0.004MHz. Initially a VCXO produces a quasi-regulated frequency in the required range. The VCXO output is fed to a mixer where it is mixed with the 13.000MHz TCXO frequency. The mixer, after low-pass filtering to remove unwanted products, produces a nominal frequency of 12kHz. This is converted to digital form and transported to the frequency-control block in custom logic.The frequency-control block compares the mixer output frequency with a reference generated by the digital clock and creates a DC error signal. A programmed offset is also added. This error signal is converted to analog form and used to control the VCXO frequency and reduce the initial error. Once settled, the loop locks to the TCXO frequency with a programmed offset frequency. The FCL output therefore acquires the TCXO’s frequency stability.Modulation The full bandwidth modulation signal is obtained from the DSP in digital form at a sample rate of 48kHz. In traditional dual-point modulation systems the modulation is applied, in analog form, to both the frequency reference and the VCO in the RF PLL, combining to produce a flat modulation response down to DC. Reference modulation is usually applied directly to the TCXO.
 TB7100 Installation and Operation Manual Functional Description 29© Tait Electronics Limited December 2005In the system employed in the transmitter board, the frequency reference is generated by the FCL, which itself requires dual-point modulation injection to allow modulation down to DC. With another modulation point required in the RF PLL, this system therefore requires triple-point modulation. The modulation signals applied to the FCL are in digital form, whereas for the RF PLL (VCO) the modulation signal is applied in analog form. The modulation cross-over points occur at approximately 30 and 300Hz as determined by the closed loop bandwidths of the FCL and RF PLL respectively.Frequency Generation The RF PLL has a frequency resolution of 25kHz. Higher resolution cannot be achieved owing to acquisition-time requirements and so for any given frequency the error could be as high as ±12.5kHz. This error is corrected by altering the reference frequency to the RF PLL. The FCL supplies the reference frequency and is able to adjust it up to ±300ppm with better than 0.1ppm resolution (equivalent to better than 50Hz resolution at the RF frequency). Fast Frequency Settling Both the FCL and RF PLL employ frequency-acquisition speed-up techniques to achieve fast frequency settling. The frequency-acquisition process of the FCL and RF PLL is able to occur concurrently with minimal loop interaction owing to the very large difference in frequency step size between the loops.Frequency Acquisitionof RF PLLIn the RF PLL the loop bandwidth is initially set high by increasing the charge pump current and reducing time constants in the loop filter. As a result settling to within 1kHz of the final value occurs in under 4ms. In order to meet noise performance requirements the loop parameters are then switched to reduce the loop bandwidth. There is a small frequency kick as the loop bandwidth is reduced. Total settling time is under 4.5ms.Frequency Acquisitionof FCLThe FCL utilises self-calibration techniques that enable it to rapidly settle close to the final value while the loop is open. The loop is then closed and settling to the final value occurs with an associated reduction in noise. The total settling time is typically less than 4 ms.Calibration The following items are calibrated in the frequency synthesizer:■nominal frequency■KVCO■KVCXO■VCO deviationCalibration of the nominal frequency is achieved by adding a fixed offset to the FCL nominal frequency; the TCXO frequency itself is not adjusted. The items KVCO and KVCXO are the control sensitivities of the RF VCO (in MHz/V) and VCXO (in kHz/V) respectively. The latter has temperature compensation.
 30 Functional Description TB7100 Installation and Operation Manual© Tait Electronics Limited December 20053.2.3 RF Power AmplifierRF Power Amplifierand Switching (50W/40W Version)The RF power amplifier and exciter of the 50W/40W radio is a five-stage line-up with approximately 40dB of power gain. The output of the frequency synthesizer is first buffered to reduce kick during power ramping. The buffer output goes to a discrete exciter that produces approximately 300 to 400mW output. This is followed by an LDMOS driver producing up to 8W output that is power-controlled. The final stage consists of two parallel LDMOS devices producing enough power to provide 40 to 50W at the RF connector.RF Power Amplifierand Switching (25W Version)The RF power amplifier of the 25W version is a four-stage line-up with approximately 37dB of power gain. The output of the frequency synthesizer is first buffered to reduce kick during power ramping. The buffer output goes to a broad-band exciter IC that produces approximately 200mW output. This is followed by an LDMOS driver producing up to 2W output that is power-controlled. The final stage consists of two parallel LDMOS devices producing enough power to provide 25W at the RF connector.Output of RFPower Amplifier The output of the RF PA passes through a dual-directional coupler, used for power control and monitoring. Finally, the output is low-pass-filtered to bring harmonic levels within specification.Power Control The steady-state power output of the transmitter is regulated using a hardware control loop. The forward power output from the RF PA is sensed by the directional coupler and fed back to the power control loop. The PA output power is controlled by varying the driver gate bias voltage that has a calibrated maximum limit to prevent overdrive. The power control signal is supplied by a 13-bit DAC driven by custom logic.Ramping Power ramp-up consists of two stages:■bias■power rampingThe timing between these two stages is critical to achieving the correct overall wave shape in order to meet the specification for transient ACP (adjacent channel power). A typical ramping waveform is shown in Figure 3.4.
 TB7100 Installation and Operation Manual Functional Description 31© Tait Electronics Limited December 2005Bias Ramp-up The steady-state final-stage bias level is supplied by an 8-bit DAC programmed prior to ramp-up but held to zero by a switch on the DAC output under the control of a TX INHIBIT signal. Bias ramp-up begins upon release by the TX INHIBIT signal with the ramping shape being determined by a low-pass filter. Owing to power leakage through the PA chain, ramping the bias takes the PA output power from less than –20dBm for the 50W/40W version or –10dBm for the 25W version to approximately 25dB below steady-state power.Power Ramp-up The power ramp signal is supplied by a 13-bit DAC that is controlled by custom logic. The ramp is generated using a look-up table in custom logic memory that is played back at the correct rate to the DAC to produce the desired waveform. The ramp-up and ramp-down waveforms are produced by playing back the look-up table in forward and reverse order respectively. For a given power level the look-up table values are scaled by a steady-state power constant so that the ramp waveform shape remains the same for all power levels.Figure 3.4 Typical ramping waveformsPowerrampHigh powerpowerLowPowerTimeBiasrampBiasramp Powerramp
 32 Functional Description TB7100 Installation and Operation Manual© Tait Electronics Limited December 20053.3 User Interface OperationThis section describes the programming/microphone connector and the controls of the user interface, and the function of the UI board.Figure 3.5 shows the controls and indicators of the user interface.Programming/Microphone ConnectorThe PROG/MIC connector can be used to connect a handset or a programming cable.TX/RX Switch The TX/RX switch changes the LCD display to show either the transmitter or the receiver channel. The TX/RX switch also determines which board will be programmed by the programming or calibration applications.The programming application is a program on a PC that is connected to the base station via the PROG/MIC connector. The programming application enables the user to program the base station with the required channels and subaudible signalling settings. The transmitter and receiver modules are programmed individually according to the setting of the TX/RX switch.The calibration application is a program on a PC that is connected to the base station via the PROG/MIC connector. The transmitter and receiver modules are designed to be totally electronically tuned. No physical tuning is required, as all tuning is done by electronic trimming. The calibration application can assist in the tuning of:■AD6521 CODEC voltage reference■TCXO frequency ■receiver front end■transmitter driver and final gate bias limit■transmitter power control■deviation and squelch.Figure 3.5 User interfacevolume controlfunction keys and LEDsinternal speakerstatus LEDs2-digit LCDdisplayTx/Rx switchprogramming/microphone connector
 TB7100 Installation and Operation Manual Functional Description 33© Tait Electronics Limited December 2005Function Keys Pressing the function keys will activate the functions assigned using the programming application. Function keys may have functions assigned to both short and long key presses. A short key press is less than one second, and a long key press is more than one second.Volume Control and Internal Speaker Rotate the volume control potentiometer clockwise to increase the speaker volume and counterclockwise to decrease the volume. By default, the base station is programmed not to generate any audible indicators.UI Board The UI board is connected to the receiver and transmitter modules via separate 18-way ribbon cables. The internal speaker is connected to the UI board via a cable with a mating connector for easy disconnection. If an internal AC Power supply is fitted, a fan power signal is routed from the fan power board to the fan via the UI board. For more information on the connectors and their signals, refer to “UI Board Connectors” on page 75.Figure 3.6 on page 34 shows a block diagram of the UI board.The UI board does not include a microprocessor. A synchronous bi-directional serial interface provides communication of key status, LCD and LED-indicator data between the transmitter/receiver modules and the UI board. The serial data is converted to or from a parallel form by a number of shift registers for the function keys and indicators. For the LCD, the serial data is fed to a driver IC that converts the serial data to a form suitable for the LCD. The keys are scanned and the LCD and LED indicators updated approximately every 50ms. The TX/RX switch controls what is displayed on the LCD and also whether the transmitter module or the receiver module will be programmed.
 34 Functional Description TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Figure 3.6 UI board block diagramReceiverModule+13V8+3V3SpeakerAudioVolume Level (DC)Rx SPI DataRx Prog DataReceiverSPI ShiftRegisters+13V8+3V3TransmitterSPI ShiftRegistersTransmitterModule ElectronicSwitchingRx SPI DataRx Prog DataSpeakerFunctionKeys andLEDsVolumeControlPowerLEDBusyLEDTxLEDLCDTx/RxSwitchProg/MicConnectorFanConnector+13V8PTTMicAudioFan PowerBoardFan Power+3V3UI Board
 TB7100 Installation and Operation Manual Functional Description 35© Tait Electronics Limited December 20053.4 System Interface OperationThis section describes the functioning of the system interface. The system interface provides:■internal power distribution■internal AC/external DC switching■serial data connection (THSD or FFSK)■fan control■general purpose IO■receiver audio processing■transmitter audio processing■opto-isolated keying■relay output■received signal strength indication (RSSI)■receiver gate output■receiver inhibit input■13.8VDC (1.5A) output■tone on idle (TOI).These functional parts are described in detail below.
 36 Functional Description TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Figure 3.7 SI board block diagram13.8V9V4.5V3.3V13.8V outPower Supplies9V 4.5VRXAUDIO OUTRX LINE OUTTX INAUDIOTX LINE INTOITONEAUD IN13.8V13.8V9V4.5V3.3VAudioControlandSignallingAUX IOTX KEYTX DATAAUX IORX GATERSSIRX DATAAUD OUTTransmitterModuleReceiverModuleTemperatureSensorFan PowerBoardFan ControlSerial DataConnectorRXDTXD13.8V outSystemConnector13.8V 3.3VRSSIRX GATEDIG IOOPTORELAY DRIVERRX INHIBITTX KEYTX DIG IORX DIG IODC PowerConnectorMains fail signal13.8VAC PowerSupply UnitFuse13.8V13.8VAGND INSI Board
 TB7100 Installation and Operation Manual Functional Description 37© Tait Electronics Limited December 20053.4.1 Internal Power DistributionThis section details how the input power feed is distributed throughout the base station to power its various sub-systems. Refer to Figure 3.8 for more information.13.8V DC This is from either the DC input on the rear of the base station, or from an optional internal AC power supply unit. When AC mains is present, power will not be drawn from the DC input. The DC power input of the base station is protected by a rear panel fuse. The 13.8V is distributed directly to Figure 3.8 Power distributionDataCircuitryControlCircuitryAudioCircuitryCWIDPowerSupplyCircuitryFan ControlCircuitryAC PowerSupply Unit Mains fail signalDCPowerSource13.8VFuseDC PowerConnectorSI BoardFanPowerBoardReceiverModule4.5V3.3V9V13.8V PowerSupplyCircuitry13.8V9V6V3.3VFrequencySynthesizerCODECandAudioReceiverDigitalBoardInterface3V2.5VTransmitterModulePowerSupplyCircuitry13.8V9V6V3.3VFrequencySynthesizerCODECandAudioTransmitterDigitalBoardInterface3V2.5VProg/MicConnectorUI BoardACPowerSource
 38 Functional Description TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005the receiver and transmitter boards and to the 13.8VDC output on the SYSTEM connector, rated at 1.5A. The 13.8VDC is also used to power the fans, via control circuitry.Note The UI board obtains 13.8V and 3.3V from the receiver module and outputs 13V8_SW to the PROG/MIC connector.3.3V, 4.5V, 9V, 13.8V The other voltages derived on the SI board are used only on the SI board.3.4.2 Serial DataTHSD Tait High Speed Data (THSD) is a proprietary protocol of Tait Electronics Limited that can be used with the base station. This allows the base station configured in either data repeater or data modem modes to pass data speeds up to 12kbps on a narrow-band channel and 19.2kbps on a wide-band channel. 1200-baud Fast Frequency Shift Keyed (FFSK) data is also available as an option.3.4.3 General Purpose IOThe transmitter and receiver boards can be programmed to act upon signals from the SI board and also outputs signals for certain conditions. These settings are discussed in “Preparation for Operation” on page 77.3.4.4 Receiver Audio ProcessingThe SI board provides an external 600Ω balanced 4-wire line for connecting 4-wire circuits of which two are used by the receiver for receive audio.The SI board provides an unbalanced audio output for connecting to other devices. Output levels can be set via the rear panel.3.4.5 Tone On IdleThe tone-on-idle (TOI) frequency is generated by the SI board and fed directly to the receiver line out. It is enabled using links on the SI board. These settings are discussed in “Preparation for Operation” on page 77. If enabled, the output of the TOI is switched by the receiver gate.3.4.6 Transmitter Audio ProcessingThe SI board provides an external 600Ω balanced 4-wire line for connecting 4-wire circuits of which two are used by the transmitter for transmit audio.
 TB7100 Installation and Operation Manual Functional Description 39© Tait Electronics Limited December 2005The SI board provides an unbalanced audio input and output for connecting to other devices.3.4.7 Opto Isolated KeyingExternal keying of the base station can be achieved using the current regulated optically isolated keying connections.3.4.8 Relay OutputThe SI board can provide a relay output with a load voltage of 350V or load current of 120mA continuous. The SI board can also provide a relay driver output. Both these options are configurable and these settings are discussed in “Preparation for Operation” on page 77.3.4.9 Fan ControlThere are three modes of operation for the fans. The modes are:■on continuous■on when transmitting■on at a pre-defined temperature.The modes of operation are selected by links on the SI board. These settings are discussed in “Preparation for Operation” on page 77.3.4.10 RSSIA received signal strength indication (RSSI) voltage is developed by the receiver module and applied directly to the SI board rear panel.3.4.11 Receiver GateThe receiver gate signal is used by the SI board to control TOI and a relay output. The receiver gate output on the SYSTEM connector can be used for external equipment such as TaitNet trunking controllers.3.4.12 Receiver InhibitThe receiver inhibit input on the SYSTEM connector is used to control the receiver gate signal. This may be used in linking applications to prevent unwanted receiver audio signals from appearing at the SI board output connector.
 40 Functional Description TB7100 Installation and Operation Manual© Tait Electronics Limited December 20053.5 Fan OperationThe cooling fans are mounted behind the front panel. All fans in the chassis must be of the same type.Dissipation of Heat Heat needs to be dissipated from a number of components within the internal AC power supply unit, transmitter and receiver modules, including the following:■9V regulator■RF PA■driver for RF PA■audio PAThe mechanisms by which the heat is conducted away in each case are described below.Dissipation of Heatfrom Transmitter The transmitter board is mounted directly onto a heatsink through which the forced air from the fans is ducted.Dissipation of Heat from Regulator and Audio PAHeat from the audio PA and 9V regulator on the receiver board is conducted away by a small aluminium heatsink and mounting boss. The heatsink and boss contact the underside of the board where the components are mounted and thermal paste ensures a good thermal transfer between the two surfaces.Dissipation of Heat from RF PAs and DriverHeat from the RF PAs and driver is conducted to the heatsink through a copper separator plate. The copper plate is fixed to the underside of the board and the components soldered directly to it. The copper plate is mounted directly to the main heatsink boss and a coating of thermal paste ensures good thermal transfer between these two surfaces.Dissipation of Heat from Internal AC Power Supply UnitAir is forced round major components within the internal AC power supply unit to keep them cool. Some air is passed through a small heatsink to keep the current-carrying semiconductor devices cool.
 TB7100 Installation and Operation Manual Installation 41© Tait Electronics Limited December 20054 InstallationThis section describes how to install the base station in a standard 19-inch rack or cabinet. It also provides some general information on safety precautions and site requirements. We recommend that you read the entire section before beginning the installation.4.1 Personal Safety4.1.1 Lethal VoltagesThe base station may be fitted with an internal AC power supply unit. If an internal AC power supply unit is fitted, a standard ICE AC power connector is fitted in the rear panel of the base station (refer to “AC Power Connection” on page 66).Warning!! The internal AC power supply unit contains voltages that may be lethal. Refer to the ratings label on the rear of the base station. The internal AC power supply contains no user-servicable parts.Important Wrong mains voltage! Before connecting to the AC power connector, ensure that the internal 115V/230V voltage mains selector switch is set to the correct mains voltage.The voltage selector switch is located under the base station cover. (Refer to “Setting the AC Mains Input Voltage” on page 50.)The base station must be installed so that the rear of the base station is located in a service access area. The internal AC power supply unit must be connected to the mains supply source by trained personnel in accordance with local and national regulations.Ensure that all power sources (AC and DC) are disconnected before opening the base station.
 42 Installation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20054.1.2 Explosive EnvironmentsWarning!! Do not operate base station equipment near electrical blasting caps or in an explosive atmosphere. Operating the equipment in these environments is a definite safety hazard.4.1.3 Proximity to RF TransmissionsDo not operate the transmitter when someone is standing within 90cm (3ft) of the antenna. Do not operate the transmitter unless you have checked that all RF connectors are secure.4.1.4 High TemperaturesTake care when handling a base station which has been operating recently. Under extreme operating conditions (+60°C [+140°F] ambient air temperature) or high duty cycles the external surfaces of the base station can reach temperatures of up to +80°C (+176°F).4.2 Equipment Safety4.2.1 ESD PrecautionsImportant This equipment contains devices which are susceptible to damage from static charges. You must handle these devices carefully and according to the procedures described in the manufacturers’ data books.We recommend you purchase an antistatic bench kit from a reputable manufacturer and install and test it according to the manufacturer’s instructions. Figure 4.1 shows a typical antistatic bench set-up.You can obtain further information on antistatic precautions and the dangers of electrostatic discharge (ESD) from standards such as ANSI/ESD S20.20-1999 or BS EN 100015-4 1994.
 TB7100 Installation and Operation Manual Installation 43© Tait Electronics Limited December 20054.2.2 Antenna LoadThe base station has been designed to operate safely under a wide range of antenna loading conditions. However, damage will occur if the load is removed while the base station is transmitting. Transmitting into a low VSWR will maximise the power delivered to the antenna.4.2.3 Equipment GroundingTo ensure safe operation, the base station must be correctly grounded as described in these installation instructions.4.2.4 Installation and Servicing PersonnelThe base station should be installed and serviced only by qualified personnel.4.3 Regulatory Information4.3.1 Distress FrequenciesThe 406 to 406.1MHz frequency range is reserved worldwide for use by Distress Beacons. Do not program transmitters to operate in this frequency range.Figure 4.1 Typical antistatic bench set-upcommon point ground (building ground or mains ground via 1MΩ series resistor)conductive wrist strap dissipative rubber bench mat
 44 Installation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20054.3.2 FCC Compliance1This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.4.3.3 Unauthorised ModificationsAny modifications you make to this equipment which are not authorised by Tait Electronics Ltd. may invalidate your compliance authority’s approval to operate the equipment.4.3.4 Health, Safety and Electromagnetic Compatibility in EuropeIn the European Community, radio and telecommunications equipment is regulated by Directive 1999/5/EC, also known as the Radio and Telecommunications Terminal Equipment (R&TTE) directive. The requirements of this directive include protection of health and safety of users, as well as electromagnetic compatibility.Intended Purpose of Product This product is an FM radio transceiver. Its intended purpose is for radio communication in Private Mobile Radio (PMR) services or Public Access Mobile Radio (PAMR) services.Important This product can be programmed for frequencies or emis-sions that may make its use illegal. A license must be obtained before this product is used. All license require-ments must be observed. Limitations may apply to transmit-ter power, operating frequency, channel spacing, and emis-sion.Declaration of Conformity Brief Declarations of Conformity appear on page 141. You can download the formal Declaration of Conformity from http://eudocs.taitworld.com/. You can also obtain a signed and dated paper copy of the Declaration of Conformity from Tait Europe Ltd.1. Refer to the specifications manual for more information on the compliance standards to which the base station has been tested and approved.
 TB7100 Installation and Operation Manual Installation 45© Tait Electronics Limited December 20054.4 Environmental Conditions4.4.1 Operating Temperature RangeThe operating temperature range is –30°C to +60°C (–22°F to +140°F) ambient temperature for the 25W base station and –30°C to +50°C (–22°F to +122°F) ambient temperature for the 50W and 40W base stations. Ambient temperature is defined as the temperature of the air at the intake to the cooling fans.4.4.2 HumidityThe humidity should not exceed 95% relative humidity through the specified operating temperature range.4.4.3 Dust and DirtFor uncontrolled environments, the level of airborne particulates must not exceed 100µg/m3.4.5 Grounding and Lightning Protection4.5.1 Electrical GroundThe base station modules are grounded by physical contact between the module mounting points and the chassis. To ensure a good ground connection you must tighten each module securely (for the correct torque refer to “Replacing Modules” in the installation and operation manual).A threaded grounding connector is provided on the rear of the tray for connection to the site ground point (for more details refer to “Connections” on page 65).4.5.2 Lightning GroundIt is extremely important for the security of the site and its equipment that you take adequate precautions against lightning strike. Because it is outside the scope of this manual to provide comprehensive information on this subject, we recommend that you conform to your country's standards organisation or regulatory body.
 46 Installation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20054.6 Recommended ToolsIt is beyond the scope of this manual to list every tool that an installation technician should carry. However, the following tools are specifically required for installing the base station:■Philips #2 tip screwdriver used to connect the DC power cables to the DC power terminals■Pozidriv PZ3 screwdriver for the M6 screws used to secure the tray to the cabinet in Tait factory-assembled systems■Torx T10 screwdriver for the M3 pan head screws with captured shake-proof washer and flat washer used to secure the modules in the tray■Torx T10 screwdriver for the M3 countersunk screws used to secure the cover and the heatsink channels to the tray■Pozidriv PZ1 screwdriver for the M3 pan head self-tapping screws used to secure the fans.You can also obtain the TBA0ST2 tool kit from your nearest Tait dealer or Customer Service Organisation. It contains the basic tools needed to install, tune and service the base station.4.7 VentilationAlways ensure there is adequate ventilation around the base station. Do not operate at high duty cycles in a sealed cabinet. You must keep the ambient temperature within the specified range, and we strongly recommend you ensure that the cooling airflow is not restricted.Important The cooling fans are mounted behind the front panel. To ensure adequate airflow through the base station, do not operate it for more than a few minutes with the fans discon-nected (e.g. for servicing purposes). 4.7.1 Cabinet and Rack VentilationRefer to Figure 4.2 on page 47.Adequate cooling airflow is critical to the performance of the base station. The cooling airflow for the base station enters through the front panel and exits at the rear of the tray. For optimum thermal performance, the heated air that has passed through a base station must not be allowed to re-enter the air intakes on the front panel. Each base station requires an unobstructed airflow of 18m3/h (11cfm).To allow enough cooling airflow through a cabinet mounted base station we recommend the following:
 TB7100 Installation and Operation Manual Installation 47© Tait Electronics Limited December 2005Figure 4.2 Typical cabinet ventilation requirementsbventilation slots dairflow entrycblanking panels eairflow exitBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUMEBUSY TF1 TF2 RF2RF1 VOLUME20cm(8in)2U≥10cm(≥4in)side view front viewtop viewccdebcc
 48 Installation TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005■a distance of 5cm minimum clearance to any obstruction to the front of the tray.■an open area of at least 50cm2 (8in2) per tray of ventilation slots or louvres in front of the air intakes for the fans for each tray; for example ten 6×85mm (0.25×3.3in) slots will allow the recommended airflow.■a distance of 10cm minimum clearance to any obstruction to the rear of the tray.■an open area of at least 50cm2 (8in2) per tray of ventilation slots or louvres in the top of the cabinet, or to the rear of each tray.■a 2U gap at the top of the cabinet.Note The ventilation opening must be unrestricted. If the slots or holes are covered with a filter, mesh or grille, the open area must be increased to allow the same airflow as an unrestricted opening.The maximum ambient temperature entering the cabinet must not exceed the maximum temperature specified for the base station.If the base station is installed in a rack or cabinet with other equipment with different ventilation requirements, we recommend that the base station be positioned below this equipment. Auxiliary Extractor Fans If multiple base stations are fitted in a cabinet, auxiliary extractor fans may be required to ensure adequate cooling. If fitted they should be capable of extracting 18m3/h (11cfm) per base station in the cabinet.If you have any other configuration, the performance of your system will depend on how closely you comply with the base station airflow requirements described above.
 TB7100 Installation and Operation Manual Installation 49© Tait Electronics Limited December 20054.8 Installing the Base Station4.8.1 Unpacking the EquipmentUnpacking the Base Station The base station is packed in a strong corrugated cardboard carton with top and bottom foam cushions.1. Cut the tape securing the flaps at the top of the carton and fold them flat against the sides.2. Rotate the carton carefully onto its side and then onto its top, ensuring that none of the flaps is trapped underneath.3. Slide the carton upwards over the foam cushions and lift it away. Remove the cushion from the bottom of the base station.4. Lift the base station clear of the remaining cushion.Disposal of Packaging If you do not need to keep the packaging, we recommend that you recycle it according to your local recycling methods. The foam cushions are CFC- and HCFC-free and may be burnt in a suitable waste-to-energy combustion facility, or compacted in landfill.4.8.2 Identifying the Mechanical ConfigurationThe base station is available in two different mechanical configurations—with or without provision for an internal AC power supply unit.The mechanical configuration with provision for an internal AC power supply has the following distinguishing features:■larger air intake on the right-hand side of the front panel■provision for AC connector on the left-hand side of the rear panel (refer to Figure 6.2 on page 66)■ground point on the right-hand side of the rear panel rather than on the left-hand side■different SI board and internal cables.
 50 Installation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20054.8.3 Power Supply OptionsThe base station is available with or without an internal AC power supply unit.All base stations have an external DC input power connector which is used as main power supply when no internal AC power supply unit is fitted.When the internal AC power supply unit is fitted, the DC input can be used as a DC backup power option. In case of AC mains failure the base station will automatically and seamlessly switch to DC power input.If no internal AC power supply unit is fitted, an external Tait T809-10-87xx power supply can be used to supply the DC voltage required.4.8.4 Setting the AC Mains Input VoltageWarning!! The internal AC power supply unit contains voltages that may be lethal. Refer to the ratings label on the rear of the base station.Ensure that all power sources (AC and DC) are disconnected before opening the base station.1. Disconnect all power sources before opening the base station.2. Use a Torx T10 screwdriver to remove the 15 countersunk screws securing the cover to the tray.3. Set the 115V/230V AC mains voltage selector switch to the correct AC mains input voltage (Figure 4.3).Figure 4.3 115/230V AC mains voltage selector switch115/230V AC mains voltage selector switch
 TB7100 Installation and Operation Manual Installation 51© Tait Electronics Limited December 20054.8.5 Mounting the Base Station1. Fit the base station into the cabinet or rack and secure it firmly with an M6 (or 0.25in if you are using imperial fittings) screw, flat and spring washer in each of the four main mounting holes b, as shown in Figure 4.4 on page 51.2. The base station can be wall-mounted by rotating the front mounting brackets and fitting the optional rear brackets (TBBA03-01). When the base station is wall-mounted ensure the airflow is from bottom to top (front panel mounted down) or side to side.3. For transport or in installations subject to vibration, the base station should be supported at the rear using a transit bracket (Tait recommends to use the TB7100 transit bracket, Tait part number 302-05282-00).Figure 4.4 Base station mounting points (configuration with AC power supply unit shown)bmain mounting holes eDC power connectorcbase station fAC power connectordground point Grack frameGEcbfD
 52 Installation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20054.8.6 CablingWe recommend that you route all cables to and from the base station along the side of the cabinet so the cooling airflow is not restricted.Cables should be well supported so that the connectors or terminals on the base station and on the ends of the cables do not have to support the full weight of the cables.Cables must be routed so that they do not restrict the air outlets at the rear of the base station. 4.8.7 AccessoriesThe base station can use the following accessories:■T809-10-87xx power supply■TBBA03-01 wall mounting kit■TBBA03-02 duplexer kit(mechanical configuration without internal AC power supply unit)■TBBA03-03 duplexer kit(mechanical configuration with internal AC power supply unit)■TMAA02-01 fist microphone.
 TB7100 Installation and Operation Manual Replacing Modules 53© Tait Electronics Limited December 20055 Replacing ModulesThis section describes how to:■remove and open and close the base station■remove and fit the modules and componentsGeneral Important Before disassembling the base station, disconnect the base station from any test equipment or power supply.Disassemble only as much as necessary to replace the defective parts. Inspect all disassembled parts for damage and replace them, if necessary.Observe the torque settings indicated in the relevant figures.Important To ensure adequate airflow through the base station, do not cover the fan intake grill on the front panel. Do not operate for more than a few minutes with the fan intake covered.Important The transmitter and receiver modules must only be replaced with base station modules.Saving the Base Station ConfigurationBefore replacing a module in the base station, you should decide whether you need to save its configuration data. If you are unsure whether you have a record of the configuration, use the Programming Application to read the base station and save the configuration files before removing any modules. Once you have replaced the module, you will be able to restore the original configuration by programming the saved configuration back into the base station. If one or more of the modules is faulty, you may be unable to read the base station. In this case, you will have to restore the configuration from a back-up file. Refer to the section “Preparation for Operation” on page 77 for more information.
 54 Replacing Modules TB7100 Installation and Operation Manual© Tait Electronics Limited December 20055.1 Removing the Base Station and Opening the TrayImportant The modules in the base station are not hot-pluggable. It is recommended the tray is removed from the rack before any modules are replaced.1. If an internal AC Power supply is fitted, disconnect the base station from AC power g.2. Remove the fuse e at the rear of the base station to disconnect the base station from DC power.3. Use a Philips #2 screwdriver to disconnect the cables from the DC power connector f.4. Disconnect the antenna connectors for transmit and receive d.5. Disconnect any other connectors.6. Disconnect the ground cable from the ground point c.7. Use a PZ2 Pozidriv screwdriver to remove the four M6 screws, and remove the base station from the rack.8. Use a Torx T10 screwdriver to remove the 15 countersunk screws. Remove the tray cover b.Figure 5.1 Opening the traybefdcConfiguration with internal AC power supply unit shown g
 TB7100 Installation and Operation Manual Replacing Modules 55© Tait Electronics Limited December 20055.2 Replacing the UI BoardRemoval 1. Remove the volume knob by pulling slowly but firmly. The knob is a friction fit and can leave the collet behind on the shaft. If this happens, remove the collet from the shaft and place inside the knob.2. Disconnect the speaker connector b.3. Use a Torx T10 screwdriver to remove the three screws c together with the spring washers and flat washers.4. Insert the card remover tool (220-02034-xx) from the tool kit (TBA0ST2), or a small flat-bladed screwdriver into the two small holes at the bottom of the UI board. Lever the board completely off the spring clips d.5. Carefully slide the UI board towards the rear of the base station until the volume-control shaft clears the front panel. Lift the UI board clear of the chassis.6. Disconnect the two Micro-MaTch connectors e.Fitting 1. Plug the two Micro-MaTch connectors e into the UI board. The Micro-MaTch connector for the transmitter is closest to the edge of the UI board.2. Align the volume-control shaft with the hole in the front panel, also align the programming/microphone connector and function buttons as the board is slid into place.3. Gently slide the UI board into position so that the spring clips d are engaged. Press firmly around the spring clips to ensure they are engaged fully.4. Use a Torx T10 screwdriver to fasten the three screws c to 4.5lb·in (0.5N·m).5. Plug the speaker connector b into the UI board.6. Fit the volume knob onto the shaft and press firmly until fully seated.Figure 5.2 Removing the UI boardedcbCables not shown.Torx T104.5lb·in (0.5N·m)
 56 Replacing Modules TB7100 Installation and Operation Manual© Tait Electronics Limited December 20055.3 Replacing the Receiver ModuleRemoval Note Release the latch underneath the DC power connector before attempting to disconnect it.1. Disconnect the cables to the RF b, DC power c, system interface d, and the user interface e connectors.2. Use a Torx T10 screwdriver to remove the five screws f and g together with the spring washers and flat washers.3. Lift the receiver module clear of the chassis.4. Make sure not to lose the metal heatsink g for the audio PA.Note Although the boards of the transmitter and receiver modules look alike, the board on the transmitter module can not replace a receiver module. There is no heat transfer plate on the receiver module. Check that the replacement module has links LK2, LK3 and LK4 not fitted as shown in Figure 5.3.Fitting Note Before fitting the receiver module, make sure that the metal heat-sink h for the audio PA is fitted to the tray chassis.1. Place one screw g into the hole above the metal heatsink plate by:a. holding the module at a 60° angleb. fitting the screw on the Torx driverc. slipping it through the shield hole and into the board hole.2. Position the receiver module inside the tray chassis.3. Use a Torx T10 torque-driver to tighten the screws f and g to 4.5lbf·in (0.5N·m).4. Connect the cables to the RF b, DC power c, system interface d, and user interface e connectors.Figure 5.3 Replacing the receiver modulefgebcdfCheck that links LK2, LK3 and LK4 are not fitted.Torx T104.5lb·inTorx T104.5lb·inhCables not shown.
 TB7100 Installation and Operation Manual Replacing Modules 57© Tait Electronics Limited December 20055.4 Replacing the Transmitter ModuleRemoval Note Release the latch underneath the DC power connector before attempting to disconnect it.1. Disconnect the cables to the RF b, DC power c, system interface d, and the user interface f connectors.2. Use a Torx T10 screwdriver to remove the screw h fastening the temperature sensor to the heatsink.3. Use a Torx T10 screwdriver to remove the four screws g fastening the heatsink to the tray chassis.4. Lift the transmitter module clear of the tray chassis.Fitting Note Although the boards of the transmitter and receiver modules look alike, the board on the transmitter module can not replace a receiver module. There is no heat transfer plate on the receiver module. Check that the replacement module has links LK2, LK3 and LK4 not fitted as shown in Figure 5.4.1. Position the transmitter module inside the tray chassis.2. Use a Torx T10 torque-driver to fasten the four screws g to 4.5lbf·in (0.5N·m).3. Use a Torx T10 torque-driver to fasten the temperature sensor with the screw h to 4.5lbf·in (0.5N·m).4. Connect the cables to the RF b, DC power c, system interface d, and the user interface f connectors.Figure 5.4 Replacing the transmitter modulegfbcdgeCheck that links LK2, LK3 and LK4 are not fitted.ggghTorx T104.5lb·inTorx T104.5lb·in Cables not shown.
 58 Replacing Modules TB7100 Installation and Operation Manual© Tait Electronics Limited December 20055.5 Replacing the SI BoardRemoval 1. Disconnect the system interface cables e to the transmitter and the receiver, the fan control cable f, the temperature sensor cable g, and the mains power present cable, and move them to one side.2. Remove the DC power cables h and move them to one side. Note the connection positions.3. Use a Torx T10 screwdriver to remove the two screws j.Use a PZ1 Pozidriv screwdriver to remove the screw i on the heatsink of U406.4. Carefully lift the front of the SI board off the spring clips 1).5. Carefully slide the SI board towards the front of the base station until the connectors b, c and d clear the rear panel. Lift the SI board clear of the chassis.Fitting 1. Slide the SI board into the tray chassis by fitting the connectors b, c and d into the rear panel.2. Press down firmly on the front of the SI board to engage the two spring clips j.Important Make sure that the thermal pad is fitted under and the plastic insulating washer is fitted on U406.3. Use a torque-driver to fasten the two screws j (Torx T10) the screw i (PZ1) on the heatsink of U406 to 4.5lb·in (0.5N·m). 4. Connect the system interface cables e to the transmitter and the receiver, the fan control cable f, the temperature sensor cable g, and the DC power cables h.Figure 5.5 Replacing the SI boardghbc dTorx T104.5lb·injji1)1) efPZ14.5lb·inCables not shown.
 TB7100 Installation and Operation Manual Replacing Modules 59© Tait Electronics Limited December 20055.6 Replacing the Transmitter and Receiver FansRemoval 1. Use a Torx T10 screw driver to remove the four screws b securing the fan duct d in the tray chassis.2. Disconnect the fan control loom from the fan power board c. Slide back the fan duct d and lift clear.3. Unplug the fan to be replaced from the fan power board c on the fan duct d.4. Use a PZ1 Pozidriv screwdriver to remove the two M3×25mm screws e and remove the fan.Fitting 1. Place the fan into position on the fan duct e and use a PZ1 screwdriver to fasten the two M3×25 screws e to 4.5lb·in (0.5N·m).2. Thread the fan cable through the hole in the side of the fan duct. Plug the fan into the fan power board c.3. Slide the fan duct d into the chassis. Plug the fan control loom into the fan power board c.4. Use a Torx T10 screwdriver to fasten the four screws b to 4.5lb·in (0.5N·m).Figure 5.6 Replacing the transmitter and receiver fansbbcdefTorx T104.5lb·inPZ14.5lb·in
 60 Replacing Modules TB7100 Installation and Operation Manual© Tait Electronics Limited December 20055.7 Replacing the Fan Power BoardNote The fan power board is manufactured as part of the UI board and cannot be ordered separately. For more information, refer to “Spare Parts” in the service manual.The circled numbers in this section refer to the items in Figure 5.6 on page 59.1. Disconnect the fan control cable and the fan cables from the fan power board c.2. Use a Torx T10 screwdriver to remove the screw f attaching the fan power board c to the fan duct d.3. Fitting is carried out in reverse order.5.8 Replacing the Temperature Sensor BoardNote The temperature sensor board is manufactured as part of the SI board and cannot be ordered separately. For more information, refer to “Spare Parts” in the service manual.1. Disconnect the temperature sensor cable from the SI board (Figure 5.5, g).2. Use a Torx T10 screwdriver to remove the screw (Figure 5.4, h) attaching the temperature sensor board to the transmitter module.3. Fitting is carried out in reverse order.
 TB7100 Installation and Operation Manual Replacing Modules 61© Tait Electronics Limited December 20055.9 Replacing the AC Power Supply Unit, Fan and Filter ModuleRemoval 1. Disconnect the base station from AC mains power.2. Remove the fuse at the rear of the base station to disconnect the base station from DC power.3. Disconnect the fan g at connector PL7 1! of the UI board.4. Use a Torx T10 screwdriver to remove the two screws e that hold the AC power supply f unit to the main chassis.5. Slide the AC power supply unit from its position to gain access to the fan.6. Use a PZ1 Posidriv screwdriver to remove the two M3 x 25mm screws h that hold the fan in place, and remove the fan.7. Disconnect the cable for the mains fail signal at J110 c and the DC power cable at J102 b of the SI board.8. Disconnect the connection (not shown) from the AC filter module d to the AC power supply unit, and remove the AC power supply unit.9. Slide the AC filter module from its position and remove it.Figure 5.7 Replacing the AC power supply unit, fan, filter module, and speakerheTorx T104.5lb·in dfe1)bcgPZ14.5lb·ini1!jTorx T104.5lb·inCables not shown.
 62 Replacing Modules TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Fitting 1. Slide the AC filter module d into the securing tabs at the rear of the tray.2. Place the fan g into position on the AC power supply unit f and use a PZ1 screwdriver to fasten the two M3×25 screws h to 4.5lb·in (0.5N·m).3. Connect the AC power supply unit to the AC filter module.4. Slide the AC power supply unit into position on the tray and connect the fan to connector PL7 1! on the UI board.5. Use a Torx T10 screwdriver to fasten the two screws e that hold the AC power supply unit in place to 4.5lb·in (0.5N·m).6. Connect the cable for the mains fail signal at J110 c and the DC power cable at J102 b of the SI board.5.10 Replacing the SpeakerThe circled numbers in this section refer to the items in Figure 5.7 on page 61.1. Disconnect the speaker cable from connector PL2 1) on the UI board.2. Use a Torx T10 screw driver to remove the two screws and washers i securing the speaker i to the tray.3. Fitting is carried out in reverse order. The torque for the Torx T10 screws i is 4.5lb·in (0.5N·m).
 TB7100 Installation and Operation Manual Replacing Modules 63© Tait Electronics Limited December 20055.11 Final ReassemblyFigure 5.8 shows the assembled configuration with internal AC power supply unit. Figure 5.9 shows the assembled configuration without internal AC power supply unit.1. Ensure all internal cables are connected correctly as shown below.2. Place the tray cover onto the chassis.3. Use a Torx T10 torque-driver to fasten the tray cover with the 15 countersunk screws to 4.5lb·in (0.5N·m).4. Fit the fuse b at the rear of the base station.Figure 5.8 Final reassembly (configuration with internal AC power supply unit)Fuse
 64 Replacing Modules TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Figure 5.9 Final reassembly (configuration without internal AC power supply unit)Fuse
 TB7100 Installation and Operation Manual Connections 65© Tait Electronics Limited December 20056 ConnectionsOverview This section gives an overview of looms and cables, and describes the specifications and pinouts of the external and internal connectors.Figure 6.1 provides an overview of the connections.For information on the factory connector and the internal options connector of the transmitter and receiver, refer to the PCB information.Figure 6.1 Connectors, looms and cables DC InputConnector SystemConnector Serial DataConnector AC InputConnectorRxConnectorTx/AntConnectorGroundPointTransmitterModuleUI BoardACPower SupplyUnitFanFanFanFan Power BoardSpeakerTemperatureSensorProg/MicConnectorReceiver/SIDC powerRFTransmitter/SIRFReceiver/UITransmitter/UIAC Input FilterModule115V/230VSelectorSwitchSI BoardFuseMains fail signalSK100PL100 SK101 SK103SK100PL100 SK101 SK103RF connectorDC powerconnectorAuxiliaryconnectorUser interfaceconnectorReceiverModuleRF connectorDC powerconnectorAuxiliaryconnectorUser interfaceconnectorJ102 J103J105 J106 J104J201J200J110J100 J202J101DC powerFan powerSK1SK3SK2PL2PL7PL8PL4PL3PL5PL6FactoryonlyPL101J600DC OutputAC powerConfiguration with internal AC power supply unit shown
 66 Connections TB7100 Installation and Operation Manual© Tait Electronics Limited December 20056.1 External ConnectorsFigure 6.2 shows the external connectors:AC Power Connection If an internal AC power supply unit is fitted, AC power is available in 195VAC to 264VAC or 99VAC to 135VAC. The voltage selector switch is located under the base station cover. (Refer to “Setting the AC Mains Input Voltage” on page 50.)The AC power connector at the rear of the base station is a standard 3-way AC pin connector.Warning!! The internal AC power supply unit contains voltages that may be lethal. Refer to the ratings label on the rear of the base station. The internal AC power supply contains no user-servicable parts.Important Wrong mains voltage! Before connecting to the AC power connector, ensure that the internal 115V/230V voltage mains selector switch is set to the correct mains voltage.The base station must be installed so that the rear of the base station is located in a service access area. The internal AC power supply unit must be connected to the mains supply source by trained personnel in accordance with local and national regulations.Ensure that all power sources (AC and DC) are disconnected before opening the base station.Figure 6.2 External connectors (configuration with internal AC Power supply unit shown)programming/microphone connector (PROG/MIC)groundpointserial data connector(IOIOI)system connector(SYSTEM)DC power connector(13.8VDC 13A MAX)receiver antenna connector(RX)transmitter antennaconnector(TX/ANT)* *Tx/ANT is Tx and Rx, if the duplexer is fitted.AC power connector
 TB7100 Installation and Operation Manual Connections 67© Tait Electronics Limited December 2005DC Power Connection The base station is designed to accept a nominal 13.8V DC, with negative ground.The DC power connector (J105) at the rear of the base station is a heavy-duty M4 screw terminal connector suitable for many forms of connection.You must connect the DC supply from the battery to the base station via a readily accessible disconnect device such as a fuse or DC-rated circuit breaker with the appropriate rating, as shown in the table below. The DC input leads should be of a suitable gauge to ensure less than 0.2V drop at maximum load over the required length of lead. Terminate the DC input leads with a suitable crimp connector for attaching to the J105 M4 screws.Ground Point The ground point is a terminal for grounding the tray to the mounting rack.Pin Signal Name Signal Type Notes1 13.8VDC input2 ground inputexternal viewNominal Supply Voltage Input Voltage RangeCircuit Breaker/Fuse RatingRecommended Wire Gaugeaa. For a length of 1.5m to 2m (5ft to 6.5ft) (typical).13.8VDC 10VDC to 16VDC 20A 8AWG / 8.35mm2Figure 6.3 Recommended DC power connectionBatteryTB7100base stationCircuit Breakeror Fuse
 68 Connections TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005RF Connections (RXand TX/ANT)The RF input to the base station is via the RX connector (N-type) on the rear panel of the base station. The RF output is via the TX/ANT connector (N-type) on the rear panel of the base station.The RF connector is an N-type connector with an impedance of 50Ω.Important The maximum RF input level is +27dBm. Higher levels may damage the radio.Pin Signal Name Signal Type Notes1 RF RF analog2 GND RF groundBCrear view
 TB7100 Installation and Operation Manual Connections 69© Tait Electronics Limited December 2005System Connector (SYSTEM)The system connector (J106) at the rear of the base station is a 25-way standard-density D-range socket.Pin Signal Name Signal Type Notes1 Rx line output + audio output transformer isolated line <6dBm2 Tx/Rx digital input 1(AUX_GPI1) input high ≥1.7 V, low ≤0.7 V3 Tx/Rx digital input 2(AUX_GPI2)4 Rx line output – audio output transformer isolated line5 Tx line input + audio input transformer isolated line6 Tx/Rx digital input 3(AUX_GPI3) input high ≥1.7 V, low ≤0.7 V7 Tx/Rx digital input 4 (AUX_GPIO4) input output: high ≥3.1 V (no load), low <0.6 V (10mA sink)input: high ≥1.7 V, low ≤0.7 V8 Tx line input – audio input transformer isolated line9 RSSI output DC signal, 0.6 to 2.5V10 Tx digital in/out 1(TX_AUX_GPIO5) input/output output: high ≥3.1 V (no load), low <0.6 V (10mA sink)input: high ≥1.7 V, low ≤0.7 V11 Tx audio input audio input12 Tx digital in/out 2(TX_AUX_GPIO6) input/output output: high ≥3.1 V (no load), low <0.6 V (10mA sink)input: high ≥1.7 V, low ≤0.7 V13 ground ground14 Rx gate output open collector15 Tx key input active low16 Rx relay (comm) output opto-isolated17 Rx relay (NO or NC) output18 Rx Inhibit input 0 to 3.3V, active low19 Rx digital in/out 1(RX_AUX_GPIO5) input/output output: high ≥3.1 V (no load), low <0.6 V (10mA sink)input: high ≥1.7 V, low ≤0.7 V20 Tx Opto input + input input voltage range 10VDC to 60VDC21 Tx Opto input – input22 Rx digital in/out 2(RX_AUX_GPIO6) input/output output: high ≥3.1 V (no load), low <0.6 V (10mA sink)input: high ≥1.7 V, low ≤0.7 V23 Digital output/Tx relay output active low, sinks up to 250mA24 Rx audio output output <4.4Vpp25 13.8 volt output power output resetable SMD fuse 1.5Aexternal viewBCDEFGHIJ1)1!1@1#1$1%1^1&1*1(2)2!2@2#2$2%
 70 Connections TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Serial Data Connector (IOIOI)The serial data connector (J1054) labelled IOIOI is a 9-way female D-range connector, which provides a data connection to the base station.Programming/Microphone Connector (PROG/MIC)The PC running the programming and calibration application is connected to the base station via the programming/microphone connector (SK3) of the UI board. The programming/microphone connector is an 8-way RJ45 socket. Use the TPA-SV-006 or the T2000-A19 programming lead and a TMAA20-04 adapter to connect the PC to the base station. It is possible to plug the RJ11 directly into the RJ45 socket without the use of the adapter, but this is not recommended. A microphone can also be connected to the base station via this connector. Pin Signal Name Signal Type Notes1 not connected not used2 receive data output data transmitted by TB71003 transmit data input data received by TB71004 not connected not used5 ground ground6 not connected not used7 ready to transmit output request to send8 clear to send input clear to send9 not connected not usedhjbgicdefexternal viewPin Signal Name Signal Type Notes1 not connected not connected2 +13V8_SW output +13.8V, 250mA3 TXD input transmit data4 PTT input PTT5 MIC_AUD_IN input voice band (microphone) input6 GND ground7 RXD output  receive data8 not connected not connected12345678external view
 TB7100 Installation and Operation Manual Connections 71© Tait Electronics Limited December 20056.2 Internal Connectors6.2.1 Transmitter and Receiver ConnectorsThe internal connectors of the transmitter and receiver are the same for both modules. Note The signals on the user interface connectors are different for the transmitter and the receiver.RF Connectors The RF connectors of the transmitter and the receiver are N-type connectors with an impedance of 50Ω.DC Power Connectors The DC power connectors of the transmitter and the receiver are the interface for the primary 13.8V power source. There are different DC power connectors for the 50W/40W and 25W versions.Pin Signal name Signal type Notes1AGND ground2 SPK– analog output not connected3 SPK+ analog output not connected4 13.8VDC DC power inputexternal view50W/40W1 2 3 4external view25W
 72 Connections TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Auxiliary Connectors The auxiliary connectors of the transmitter and receiver are 15-way standard-density D-range sockets.User Interface Connector  The user interface connectors (SK100) of the transmitter and the receiver is a 15-way moulded plastic connector.Pin Signal Name Signal Type Notes1 AUX GPIO72 AUX GPIO43 AUX RXD input4 AUX GPI35 AUX GPI26 RSSI output7 AUX TAP IN input8 13.8VDC SW output9 AUX GPIO610 AUX GPIO411 AUX TXD output12 AUX GPI113 AUD TAP OUT output14 AUX MIC AUD input15 AGND groundexternal viewJBCDEFGHI1)1!1@1#1$1%Pin Signal Name Signal Type NotesTransmitter Receiver1 RX AUD no connection no connection no connection2 13.8VDC no connection output +13V8DC for UI board3 CH TXD input input programming data4 CH PTT input no connection microphone PTT5 CH MIC AUD input output audio from microphone6 AGND ground ground analog ground7 CH RXD output output programming data8 DGND ground ground digital ground9 CH ON OFF output output digital ground10 VOL WIP DC input input volume control11 CH SPI D0 output output12 CH LE output output13 CH GPIO1 output output digital ground14 3.3VDC no connection output +3V3DC for UI board15 CH SPI D1 input input16 CH SPI CLK output output17 SPK- no connection output speaker audio18 SPK+ no connection output speaker audio123456781012141618911131517external viewpin 1 closest to PCB
 TB7100 Installation and Operation Manual Connections 73© Tait Electronics Limited December 20056.2.2 SI Board ConnectorsDC Power Connectors The two DC power connectors (J102 and J103) on the SI board are heavy-duty M4 screw terminals. J102 (if fitted) accepts power from the internal AC power supply unit. J103 distributes the DC power to the transmitter and the receiver.System Interface Connector to TransmitterThe system interface connector (J101) to the transmitter is a 16-way surface-mounted connector.Pin Signal Name Signal Type Notes1 Tx and Rx 13.8VDC J102 :inputJ103: output2 Tx and Rx ground J102 :inputJ103: outputexternal viewPin Signal Name Signal Type Notes1 TX_AUX_GPIO7 output Tx key signal2 TX_AUX_GPIO6 bidirectional digital input/output3 TX_AUX_GPIO5 bidirectional digital input/output4 TX_AUX_GPIO4 bidirectional digital input/output5 TX_AUX_RXD input data6 TX_AUX_TXD output data7 TX_AUX_GPI3 input digital input8 TX_AUX_GPI1 input digital input9 TX_AUX_GPI2 input digital input10 TX_AUD_TAP_OUT no connection11 TX_RSSI no connection12 TX_MIC_AUD output13 TX_AUD_TAP_IN output Tx audio14 TX_GND ground ground15 TX_13V8 no connection16 N/C no connectionexternal view121615
 74 Connections TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005System Interface Connector to ReceiverThe system interface connector (J100) to the receiver is a 16-way surface-mounted connector.Pin Signal Name Signal Type Notes1 RX_AUX_GPIO7 input gate signal2 RX_AUX_GPIO6 bidirectional digital input/output3 RX_AUX_GPIO5 bidirectional digital input/output4 RX_AUX_GPIO4 bidirectional digital input/output5 RX_AUX_RXD input data6 RX_AUX_TXD output data7 RX_AUX_GPI3 input digital input8 RX_AUX_GPI1 input digital input9 RX_AUX_GPI2 input digital input10 RX_AUD_TAP_OUT input receive audio11 RX_RSSI input RSSI12 RX_MIC_AUD no connection13 RX_AUD_TAP_IN no connection14 RX_GND ground ground15 RX_13V8 no connection16 N/C no connection121615external view
 TB7100 Installation and Operation Manual Connections 75© Tait Electronics Limited December 20056.2.3 UI Board ConnectorsUser Interface Connector to TransmitterThe user interface connector (SK1) to the transmitter is a 16-way MicroMaTch connector..User Interface Connector to ReceiverThe user interface connector (SK2) to the receiver is a 16-way MicroMaTch connector.Pin Signal Name Signal Type Notes1 TX_RX_AUD no connection no connection2 TX_+13V8_SW no connection no connection3 TX_CH_TXD output programming data4 TX_CH_PTT output microphone PTT5 TX_MIC_AUD_OUT output audio from microphone6 TX_AGND ground analogue ground7 TX_CH_RXD input programming data8 TX_DGND ground digital ground9 TX_CH_ON_OFF input digital ground10 TX_VOL_WIP_DC output no connection11 TX_CH_SPI_D0 input12 TX_CH_LE input13 TX_CH_SPIO1 input digital ground14 TX_+3V3 no connection no connection15 TX_CH_SPI_DI output16 TX_CH_SPI_CLK input17 TX_CH_SPK- no connection no connection18 TX_CH_SPK+ no connection no connection12external viewPin Signal Name Signal Type Notes1 RX_RX_AUD no connection no connection2 RX_+13V8_SW input +13V8DC for PCB3 RX_CH_TXD output programming data4 RX_CH_PTT no connection no connection5 RX_MIC_AUD_OUT input no connection6 RX_AGND ground analogue ground7 RX_CH_RXD input programming data8 RX_DGND ground digital ground9 RX_CH_ON_OFF input digital ground10 RX_VOL_WIP_DC output volume control11 RX_CH_SPI_D0 input12 RX_CH_LE input13 RX_CH_GPIO1 input digital ground14 RX_+3V3 input +3V3DC for PCB15 RX_CH_SPI_DI output16 RX_CH_SPI_CLK input17 RX_CH_SPK- input speaker audio18 RX_CH_SPK+ input speaker audioexternal view12
 76 Connections TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005
 TB7100 Installation and Operation Manual Preparation for Operation 77© Tait Electronics Limited December 20057 Preparation for Operation7.1 IntroductionThe base station operation can be modified by the use of links and programmable settings.The base station can be configured for operation in the following basic modes of operation:■Line-controlled base: The base station transmit audio and key is derived via the system interface. Audio response is link-selectable.■Talk through repeater (voice): The receiver audio is directly connected to the transmitter and the transmitter is keyed by the receiver gate. Audio response in this mode is software-selectable.■Data repeater: The received data line is connected to the transmit data line. receiver gate and transmitter key signals are not used.■RF modem: Data on the serial interface is connected to the transmitter and the receiver.■TaitNet trunking.7.2 Mode of OperationThis section shows how to set up the base station for various modes of operation.Examples are:■line-controlled base■talk through repeater■RF modem■data repeater■TaitNet trunking.Where applicable, the procedure for setting any of the audio levels or other adjustment points will be described, along with the procedure for measuring a variety of parameters commonly monitored. To verify the operation of the base station it is best to configure it as a line-controlled base first. In this mode of operation the receiver and transmitter modules can be independently tested because all the audio inputs and outputs are accessible via the system interface connector. When the base station has been tested as a line-controlled base, it is then a simple process to change the links to the required mode of operation and perform any additional functional testing required for that mode of operation.
 78 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20057.3 Line-controlled BaseIn the line-controlled base mode the audio and control signals are routed from the external 25-way D-range connector through the system interface to the receiver and transmitter modules. External equipment is used to control the operation of the base station.7.3.1 Test Equipment RequiredThe following test equipment is used to setup the base station for line-controlled base operation: ■TBA0STU calibration test unit (CTU) which includes the CTU adaptor and CTU cable, or■TBA0ST1 calibration test unit (CTU), TBB0STU-TBB CTU adaptor (220-02068-xx) and CTU cable (219-02888-xx)■PC, programming cables and the TB7100 programming application■digital voltmeter■DC power supply (not necessary with internal AC power supply unit option)■RF test set with:■RF power meter■modulation analyser■RF signal generator■sinad meter■audio distortion meterFigure 7.1 Line-controlled baseSystem InterfaceReceiver TransmitterRF In RF OutRx AudioRx GateTx AudioTx Key
 TB7100 Installation and Operation Manual Preparation for Operation 79© Tait Electronics Limited December 2005■audio level meter■audio signal generator.Calibration Test Unit (CTU) The CTU is used to configure and test the base station. The same CTU is used for TB8000 and TB9000 base station equipment, so only some of the features on the CTU apply to the TB7100 base station. The CTU adaptor is plugged into the system connector of the CTU. The CTU cable is plugged into the system connector of the base station.For more information on the CTU refer to the TBA0STU/TBA0STP Calibration and Test Unit Operation Manual (MBA-00013-xx).7.3.2 Test Equipment Setup1. Connect the PC to the programming port on the front panel of the base station. See “Connecting to the PC” on page 105.2. Plug the adaptor into the system connector on the CTU. Connect the adaptor cable to the system connector of the base station.Note Connections between the CTU and the test equipment will vary and are described in the relevant test steps.3. Ensure all switches on the CTU are in the 1 or OFF position (inactive).4. Connect the receiver N-type connector to the RF test set (signal generator) output port.5. Connect the transmitter N-type connector to the RF test set (power and modulation meter) input port, check the test set is rated for the transmit power of the base station.6. Connect the 13.8V power supply to the DC input on the base station, ensuring correct polarity.
 80 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20057.3.3 Link Settings Remove the cover as detailed in “Removing the Base Station and Opening the Tray” on page 54 and set the following links on the SI board.Links of the mandatory settings must be in the position indicated. Links of the optional settings must be in one of the positions listed. The defaults are generally recommended.Replace the cover as detailed in “Final Reassembly” on page 63.Table 7.1 Line-controlled base—mandatory settingsLINK Name Pins Position Function CommentsJ400 Tx Key Source 3 1-2 Line-controlled Base mode External PTT signal to transmitterJ502 Tx Audio Source 3 1-2 Line-controlled Base mode Balanced and unbalanced audio inputs to transmitterJ503 Rx AudioDestination 3 2-3 Line-controlled Base mode Received audio to balanced and unbalanced audio outputsW401W402 TOI 9V EnableTOI 4.5V Enable 22Notfitted Tone on Idle disable Refer “Tone On Idle (TOI)” on page 118 to enable idle tone.Table 7.2 Line-controlled base—optional settingsLINK Name Pins Position Function CommentsJ500 Line Out Frequency Response31-22-3 Flat responseDe-emphasis Default position is 2-3J501 Line In Frequency Response31-22-3 Flat responseDe-emphasis Default position is 2-3J507 Line In Destination 31-22-3 Tx Line In to Aux MicTx Line In to Audio Tap In Default position is 2-3.Position 1-2 is usually used only by trunking systems.J206 Fan Control 1 3 1-22-3 Fan controlled by J207Fan always on Default position is 1-2J207 Fan Control 2 3 1-22-3 Fan Tx key-controlledFan temperature-controlled Default position is 2-3
 TB7100 Installation and Operation Manual Preparation for Operation 81© Tait Electronics Limited December 20057.3.4 Applying PowerBefore turning on the base station, check that:■all looms and cables at the front and rear of the base station are fitted correctly■all connectors are secure■the 20A fuse is fitted.Turn on the power supply and check that the base station powers up correctly:■The power LED on the user interface lights up.■The LCD indicates the current channel number.Figure 7.2 System interface link positionsJ400J500 J502J503J207W401W402J206J507J501
 82 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20057.3.5 ProgrammingTo program a base station for line-controlled base operation follow the instructions below. Do not add CTCSS or any additional settings at this stage. These are covered in “Programmable Features” on page 105. See “Connecting to the PC” on page 105 before beginning.Transmitter 1. Place the transmit/receive programming switch on the user interface into the transmit position.2. Read the transmitter or start with a new transmitter data file.3. Use the reset to defaults command under the file menu to ensure all the mandatory and recommended settings are in their correct default states. 4. Open the specifications form and select the correct RF band, not required if the transmitter file was read.5. Open the channels form and add as many channels as are required. For each channel enter the:■transmit frequency■Tx subaudible signalling value (leave as “None”)■power level■bandwidth.6. Open the key settings form and select the required function for each function key.For example:■FN1 = Preset Channel ■FN2 = Preset Channel ■FN3 = Preset Channel ■FN4 = None7. Program the transmitter.Receiver 1. Place the transmit/receive programming switch on the user interface into the receive position.2. Read the receiver or start with a new receiver data file. 3. Use the reset to defaults command under the file menu to ensure all the mandatory and recommended settings are in their correct default states.4. Open the specifications form and select the correct RF band, not required if the receiver file was read.5. Open the channels form and add as many channels as are required. For each channel enter:
 TB7100 Installation and Operation Manual Preparation for Operation 83© Tait Electronics Limited December 2005■receive frequency■Rx subaudible signalling value (leave as “None”)■squelch setting■bandwidth.6. Open the key settings form and select the required function for each function key. For example:■FN1 = Preset Channel (same as transmitter)■FN2 = Preset Channel (same as transmitter)■FN3 = Preset Channel (same as transmitter)■FN4 = Monitor / Squelch override7. Program the receiver.7.3.6 Receiver Audio Level AdjustmentUnbalanced Line 1. Connect the unbalanced output from the CTU to the audio input port on the test set and set up the test set to measure the audio level.2. Set the RF signal generator to the correct RF frequency, modulated with a 1kHz audio tone at 60% of full system deviation.3. Set the RF output level to -70dBm.4. Verify that the receiver gate opens and the busy LED turns on.5. Adjust RV502 (UNBAL OUT) on the rear panel to set the unbalanced output to the required level (typically 1Vp-p).Balanced Line 1. Connect the line output from the CTU to the audio input port on the test set and set up the test set to measure the audio level.2. Turn the CTU 600 ohm switch on.3. Set the RF signal generator to the correct RF frequency modulated with a 1kHz audio tone at 60% of full system deviation.4. Set the RF output level to -70dBm.5. Verify that the receiver gate opens and the busy LED turns on.6. Adjust RV503 (BAL OUT) on the rear panel to set the balanced output to the required level (typically -10dBm).
 84 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20057.3.7 Receiver Functional TestingThis section describes how to test some parameters which are commonly monitored.Sensitivity The sensitivity can be measured using either the balanced or unbalanced audio output.1. Connect the required audio output from the CTU to the audio input port on the test set.2. Connect the RF output from the test set to the Rx input on the rear panel.3. Set up the test set to measure the SINAD level.4. Set the RF signal generator to the correct RF frequency, modulated with a 1kHz audio tone at 60% of full system deviation.5. Set the RF output level to -70dBm.6. Verify that the receiver gate opens and the busy LED turns on.7. Reduce the RF level until 12dB SINAD is obtained. Note This level will vary depending on the bandwidth and frequency response of the channel. Consult the specifications manual for val-ues.Note If the mute closes before 12dB SINAD is reached then squelch override may be programmed to a function key.Pressing this key will prevent the mute from closing.RSSI Level 1. Connect a voltmeter to the RSSI test point on the CTU.2. Set the RF signal generator to the correct RF frequency.3. Set the RF level to -100dBm.4. Verify the RSSI voltage is 1.1V±300mV.Note If necessary adjust the RF level from –50dBm to –115dBm and verify that the RSSI voltage changes at 25mV/dB.Mute Thresholds  The mute thresholds can be measured using either the balanced or unbalanced output.1. Connect the required audio output from the CTU to the audio input port on the test set.2. Set up the test set to measure the SINAD level.
 TB7100 Installation and Operation Manual Preparation for Operation 85© Tait Electronics Limited December 20053. Set the RF signal generator to the correct RF frequency, modulated with a 1kHz audio tone at 60% of full system deviation.4. Set the RF output level to –70dBm.5. Verify that the receiver gate opens and the busy LED turns on.6. Reduce the RF level until the mute closes. This RF level is the mute close threshold.7. Increase the RF level until the mute opens. This RF level is the mute open threshold.8. The difference between these two levels is the mute hysteresis.Note The mute thresholds are determined by the squelch setting pro-grammed in the receiver’s channel table.Note If the thresholds are not suitable use the calibration application to change the squelch setting on the channel table.Distortion The Rx Distortion can be measured using either the balanced or unbalanced output.Note Before beginning this test verify the test set is rated to handle the transmit power being tested.1. Connect the required audio output from the CTU to the audio input port on the test set.2. Set up the test set to measure the distortion level.3. Set the RF signal generator to the correct RF frequency, modulated with a 1kHz audio tone at 60% of full system deviation.4. Set the RF output level to –70dBm.5. The measured distortion level should be within the receiver specifications as detailed in the specifications manual.7.3.8 Transmitter Audio Level AdjustmentBalanced Line 1. Set up the test set to measure the transmitter modulation level.2. Connect the CTU line input to the audio output port on the test set.3. Set up the test set audio output to be 1kHz at the required line level (typically –10dBm).4. Activate the Tx Key switch and verify that the transmission is at the programmed power and frequency.
 86 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20055. Adjust RV500 (BAL IN) on the rear panel to the required deviation (typically 60% of full system deviation).Unbalanced Line 1. Set up the test set to measure the transmitter modulation level.2. Connect the CTU unbalanced input to the audio output port on the test set.3. Set up the test set audio output to be 1kHz at the required line level (typically 1Vp-p).4. Activate the Tx Key switch and verify that the transmission is at the programmed power level and frequency.5. Adjust RV501 (UNBAL IN) on the rear panel to the required deviation (typically 60% of full system deviation).7.3.9 Transmitter Functional TestingThis section describes how to test some parameters commonly found on RF channel test sheets.Tx Power and Frequency 1. Set up the test set to measure frequency and power level.2. Activate the Tx Key switch on the CTU.3. Verify that the measured power level and frequency match the programmed settings, within the expected accuracy of the test set and taking into account cable losses.Note If the measured value does not agree with the programmed set-tings, the transmitter module is either faulty or needs recalibrating.Audio Distortion When measuring the transmitter audio distortion, the audio input signal can be via either the balanced or unbalanced audio input.1. Connect the audio output from the test set to the required CTU audio input.2. Set up the modulation analyser in the test set to measure the distortion of the modulated audio signal.3. Set up the test set audio generator output to be 1kHz and at the level required to produce 60% full system deviation (this is the same level used in the audio level adjustment section).4. Activate the Tx Key switch and verify that the measured deviation is 60% of full system deviation.5. The measured distortion level should be within the transmitter specifications as detailed in the specifications manual.
 TB7100 Installation and Operation Manual Preparation for Operation 87© Tait Electronics Limited December 2005Note If the measured value does not agree with the programmed set-tings, the transmitter module is either faulty or needs recalibrating.Maximum Deviation When measuring the maximum deviation, the audio input signal can be via either the balanced or unbalanced audio input.If CTCSS is to be added, this should be done before carrying out this test. Refer to “Enabling Subaudible Signalling” on page 115 for instructions.1. Set up the test set to measure the deviation of the RF signal.2. Connect the audio output from the test set to the required CTU audio input.3. Set up the test set audio generator output to be 1kHz and at the required level to produce 60% full system deviation (this is the level used in the audio level adjustment section).4. Activate the Tx Key switch and verify that the measured deviation is 60% of full system deviation.5. Increase the test set audio generator output level by 20dB and sweep the audio frequency from 100Hz to 4kHz.6. The maximum measured deviation level should not exceed the full system deviation programmed for the channel.Note If the measured value exceeds the programmed settings, the trans-mitter module is either faulty or needs recalibrating.
 88 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20057.4 Talk Through RepeaterOnce the base station has been set up and tested as a line-controlled base, it is simple to convert it into a talk through repeater. In this mode of operation the received audio and receiver gate from the receiver module are looped back to the transmitter.7.4.1 Test Equipment RequiredThe following test equipment is used to setup the base station for talk through repeater operation: ■PC, programming cables and the TB7100 programming application■digital voltmeter■DC power supply■RF test set with:■RF power meter■modulation analyser■RF signal generator■sinad meter■audio distortion meter■audio level meter■audio signal generator.Figure 7.3 Talk through repeaterReceiver TransmitterSystem InterfaceRF In RF OutRx AudioRx GateTx AudioTx Key
 TB7100 Installation and Operation Manual Preparation for Operation 89© Tait Electronics Limited December 20057.4.2 Test Equipment Setup1. Connect the PC to the programming port on the front panel of the base station. See “Connecting to the PC” on page 105.2. Connect the receiver N-type connector to the RF test set (signal generator) output port.3. Connect the transmitter N-type connector to the RF test set (power and modulation meter) input port, check the test set is rated for the transmit power of the base station.4. Connect the 13.8V power supply to the DC input on the base station, ensuring correct polarity.7.4.3 Link SettingsRemove the cover as detailed in “Removing the Base Station and Opening the Tray” on page 54 and set the following links on the SI board.Links of the mandatory settings must be in the position indicated. Links of the optional settings must be in one of the positions listed. The defaults are generally recommended.Replace the cover as detailed in “Final Reassembly” on page 63.Table 7.3 Talk through repeater—mandatory settingsLINK Name Pins Position Function CommentsJ400 Tx Key Source 3 2-3 Talk Through Repeater mode Receiver gate keys transmitterJ502 Tx Audio Source 3 2-3 Talk Through Repeater mode Transmitter audio taken from the receiverJ503 Rx AudioDestination 3 1-2 Talk Through Repeater mode Received audio to the transmitterW401W402 TOI 9V EnableTOI 4.5V Enable 22Notfitted Tone on Idle disable Tone on idle not used in repeater configurationTable 7.4 Talk through repeater—optional settingsLINK Name Pins Position Function CommentsJ507 Line In Destination 31-22-3 Tx Line In to Aux MicTx Line In to Audio Tap In Default position is 2-3J206 Fan Control 1 3 1-22-3 Fan controlled by J207Fan always on Default position is 1-2J207 Fan Control 2 3 1-22-3 Fan Tx key-controlledFan temperature-controlled Default position is 2-3
 90 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Note By default the audio frequency response will be flat. 7.4.4 Applying PowerBefore turning on the base station, check that:■all looms and cables at the front and rear of the base station are fitted correctly■all connectors are secure■the 20A fuse is fitted.Turn on the power supply and check that the base station powers up correctly:■The power LED on the user interface lights up.■The LCD indicates the current channel number.7.4.5 Programming No changes to the values programmed for line-controlled base operation are required. See “Programming” on page 82 for details.Note If a soft tail setting is required see later in this chapter “Soft Off (Tx Tail Time)” on page 118.Figure 7.4 System interface link positionsJ400J500 J502J503 J501
 TB7100 Installation and Operation Manual Preparation for Operation 91© Tait Electronics Limited December 20057.4.6 Audio Level AdjustmentThere is no audio level adjustment necessary in repeater mode. The internal linking is designed to produce a repeater with no talk through gain. If talk through gain is required it can be implemented by linking back the audio using a DB25 connector on the system interface and setting the audio levels as required, see “Alternate Talk Through Repeater Configuration” on page 92 for a more detailed explanation.7.4.7 Talk Through Repeater Functional TestingThe basic operation of the base station has already been tested as a line-controlled base. This section describes the additional functional tests required to verify that the base station is operating correctly as a repeater.Repeater Key With the test set in duplex mode: 1. Set up the test set to measure the transmitter power and frequency output.2. Set the RF signal generator to the correct frequency for the receiver.Note If subaudible signalling has been added, also modulate the carrier with the required signal.3. Set the RF level to -70dBm.4. The receiver busy LED turns on and the transmitter keys up and transmits at the programmed power level and frequency. When the RF source is removed, the transmitter will stop transmitting.Talk Through  With the test set in duplex mode: 1. Set up the test set to measure the modulation level and frequency.2. Set the RF signal generator to the correct frequency for the receiver. 3. Modulate the RF carrier with a 1kHz audio tone at 60% full system deviation.Note If subaudible signalling has been added, also modulate the carrier with the required signal.4. Set the RF level to –70dBm.5. The receiver busy LED turns on and the transmitter keys up and transmits at the programmed power level and frequency. The transmitted signal will be the same as received. If subaudible signalling has been enabled, the required sub-tone will also be transmitted.6. Ensure the deviation is at the desired level.
 92 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20057.4.8 Alternate Talk Through Repeater ConfigurationAudio Frequency Response When a talk through repeater is created by linking the audio path using links J502 and J503, the default frequency response is flat audio. The pre/de- emphasis links J500 and J501 are not in the audio path and have no effect.Repeater Talk Through Gain When a talk through repeater is created by linking the audio path using links J502 and J503, the repeater will have no talk through gain. If talk through gain is required internally link the base station for line-controlled base operation. Then externally configure it to operate as a repeater by linking the following pins on a 25pin male D-range connector and plugging the connector into the system connector on the rear panel of the base station.When configured as described above:■The base station will operate as a repeater.■The Talk through gain can be set by adjusting the line output level and line input sensitivity RV500 (BAL IN) and RV503 (BAL OUT) on the rear panel.■The pre/de emphasis links J500 and J501 can be used to set the audio frequency response.Pins Function1 to 5 Rx Line Out+ to Tx Line In+4 to 8 Rx Line Out- to Tx Line In-14 to 15 Rx Gate to Tx Key
 TB7100 Installation and Operation Manual Preparation for Operation 93© Tait Electronics Limited December 20057.5 RF ModemIn RF modem mode the transmitter and receiver are connected to the serial interface and any data on the serial interface is transmitted. Any data received is forwarded to the PC.7.5.1 Test Equipment RequiredThe following test equipment is used to setup the base station for RF modem operation: ■TBA0STU calibration test unit (CTU) which includes the CTU adaptor and CTU cable, or■TBA0ST1 calibration test unit (CTU), TBB0STU-TBB CTU adaptor (220-02068-xx) and CTU cable (219-02888-xx)■PC, programming cables and the TB7100 programming application■digital voltmeter■DC power supply■RF test set with:■RF power meter■modulation analyser■RF signal generator■sinad meter■audio distortion meter■audio level meter■audio signal generatorFigure 7.5 RF modemSerial InterfaceReceiver TransmitterRF In RF OutRx DataTx Data
 94 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Calibration Test Unit (CTU) The CTU is used to configure and test the base station. The same CTU is used for TB8000 and TB9000 base station equipment, so only some of the features on the CTU apply to the TB7100 base station. The CTU adaptor is plugged into the system connector of the CTU. The CTU cable is plugged into the system connector of the base station.For more information on the CTU refer to the TBA0STU/TBA0STP Calibration and Test Unit Operation Manual (MBA-00013-xx).7.5.2 Test Equipment Setup1. Connect the PC to the programming port on the front panel of the base station. See “Connecting to the PC” on page 105.2. Connect the receiver N-type connector to the RF test set (signal generator) output port.3. Connect the transmitter N-type connector to the RF test set (power and modulation meter) input port, check the test set is rated for the transmit power of the base station.4. Connect the 13.8V power supply to the DC input on the base station, ensuring correct polarity.7.5.3 Link SettingsRemove the cover as detailed in “Removing the Base Station and Opening the Tray” on page 54 and set the following links on the SI board.Links of the mandatory settings must be in the position indicated. Links of the optional settings must be in one of the positions listed. The defaults are generally recommended.Replace the cover as detailed in “Final Reassembly” on page 63.Table 7.5 RF modem—mandatory settingsLINK Name Pins Position Function CommentsJ221 RS232 Loop Back 3 1-2 RS-232 out data connectorJ400 Tx Key Source 3 1-2 External Tx key source Use this setting because the transmitter will automatically key up when there is data to send so should not be keyed by the receiver gate.
 TB7100 Installation and Operation Manual Preparation for Operation 95© Tait Electronics Limited December 20057.5.4 Applying PowerBefore turning on the base station, check that:■all looms and cables at the front and rear of the base station are fitted correctly■all connectors are secure■the 20A fuse is fitted.Turn on the power supply and check that the base station powers up correctly:■The power LED on the user interface lights up.■The LCD indicates the current channel number.Table 7.6 RF modem—optional settingsLINK Name Pins Position Function CommentsJ206 Fan Control 1 3 1-22-3 Fan controlled by J207Fan always on Default position is 1-2J207 Fan Control 2 3 2-3 Fan temperature-controlled Do not use position 1-2 (Tx key-activated fan). The transmitter will automatically key up when there is data to send. This will not activate the Tx key line and therefore will not activate the fan.Figure 7.6 System interface link positionsJ221
 96 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20057.5.5 ProgrammingPlease see the line-controlled base “Programming” on page 82 for details on how to program the base station for RF modem operation.7.5.6 Audio Level AdjustmentIn this configuration the system interface connector is not used, so it is not necessary to set the line output level or line input sensitivity.7.5.7 Programming for FFSK OperationTo program a base station for FFSK operation:Transmitter  1. Read the transmitter or start with a new transmitter data file.2. Use the reset to defaults command under the file menu to ensure all the mandatory and recommended settings are in their correct default states.3. Open the specifications form and select the correct RF band4. Open the channels form summary tab. Add as many channels as are required and for each channel enter the following:■transmit frequency■Tx subaudible signalling value■power level■bandwidth.5. Open the channels form details tab and for each channel check the Use channel for data check box.6. Open the key settings form and select the required function for each function key. For example:■FN1 = Preset Channel■FN2 = Preset Channel■FN3 = Preset Channel■FN4 = None.7. Open the data form and in the general tab:■In the command mode section disable all check boxes.■In the transparent mode section select transparent mode enabled and de-select the other check boxes.■Set Power Up State to FFSK transparent mode.8. Open the data form and in the serial communications tab:■In the serial communications setup field set the FFSK transparent
 TB7100 Installation and Operation Manual Preparation for Operation 97© Tait Electronics Limited December 2005mode baud rate to 1200, the Flow control to None and the data port to the required data port.■Ensure hardware flow control is set to None.9. Open the data form RF modems tab. The THSD modem settings do not apply and can be ignored. In the FFSK modem section set up the following:■Ignore CTCSS/DCS can be disabled (CTCSS/DCS is not used in this example).■Enable Check Packet Length.■Disable FFSK Tone Blanking.■FFSK Lead-In Delay default of 500ms is suitable but can be changed.■FFSK Lead-Out Delay default of 200ms is suitable but can be changed.10. Program the transmitterReceiver 1. Read the receiver or start with a new receiver data file.2. Use the reset to defaults command under the file menu to ensure all the mandatory and recommended settings are in their correct default states.3. Open the specifications form and select the correct RF band.4. Open the channels form summary tab. Add as many channels as are required and for each channel enter the following:■receive frequency■Rx subaudible signalling value■squelch setting■bandwidth.5. Open the channels form details tab and for each channel check the use channel for data check box.6. Open the key settings form and select the required function for each function key. For example:■FN1 = Preset Channel (same as transmitter)■FN2 = Preset Channel (same as transmitter)■FN3 = Preset Channel (same as transmitter)■FN4 = Monitor / Squelch override7. Open the data form and in the general tab:■In the command mode section disable all check boxes.■In the transparent mode section select transparent mode enabled and de-select the other check boxes.■Set Power Up State to FFSK transparent mode.
 98 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20058. Open the data form and in the serial communications tab:■In the serial communications setup field set the FFSK transparent mode baud rate to 1200, the Flow control to None and the data port to the required data port.■Ensure hardware flow control is set to None.9. Open the data form RF modems tab. The THSD modem settings do not apply and can be ignored. In the FFSK modem section set up the following:■Ignore CTCSS/DCS can be disabled (CTCSS/DCS is not used in this example).■Enable Check Packet Length.■Disable FFSK Tone Blanking.■FFSK Lead-In Delay default of 500ms is suitable but can be changed.■FFSK Lead-Out Delay default of 200ms is suitable but can be changed.10. Program the receiver.7.5.8 Programming for THSD OperationTransmitter 1. Read the transmitter or start with a new transmitter data file.2. Use the reset to defaults command under the file menu to ensure all the mandatory and recommended settings are in their correct default states.3. Open the specifications form and select the correct RF band.4. Open the channels form summary tab. Add as many channels as are required and for each channel enter the following:■transmit frequency■Tx subaudible signalling value = Ignored in THSD Mode■power level■bandwidth.5. Open the channels form details tab and for each channel check the use channel for data check box.6. Open the key settings form and select the required function for each function key. For example:■FN1 = Preset Channel■FN2 = Preset Channel■FN3 = Preset Channel■FN4 = None
 TB7100 Installation and Operation Manual Preparation for Operation 99© Tait Electronics Limited December 20057. Open the data form and in the general tab:■In the command mode section disable all check boxes.■In the transparent mode section select transparent mode enabled and THSD modem enabled and de-select the ignore escape sequence check box.■Set Power Up State to THSD transparent mode.8. Open the data form and in the serial communications tab:■In the serial communications setup field set the THSD transparent mode baud rate to 9600, the Flow control to None and the data port to the required data port.■Ensure hardware flow control is set to None.9. Open the data form RF modems tab. The FFSK modem settings do not apply and can be ignored. In the THSD modem section set up the following:■Wide band modem enabled■Layer 2 Protocol enabled■Forward Error Correction disabled■THSD Lead-in Delay default of 30ms is acceptable.10. Program the transmitter.Receiver 1. Read the receiver or start with a new receiver data file.2. Use the reset to defaults command under the file menu to ensure all the mandatory and recommended settings are in their correct default states.3. Open the specifications form and select the correct RF band.4. Open the channels form summary tab. Add as many channels as are required and for each channel enter the following:■receive frequency■Rx subaudible signalling value = Ignored in THSD Mode■squelch setting■bandwidth.5. Open the channels form details tab and for each channel check the use channel for data check box.6. Open the key settings form and select the required function for each function key. For example:■FN1 = Preset Channel (same as transmitter)■FN2 = Preset Channel (same as transmitter)■FN3 = Preset Channel (same as transmitter)■FN4 = Monitor / Squelch override.
 100 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20057. Open the data form and in the general tab:■In the command mode section disable all check boxes.■In the transparent mode section select transparent mode enabled and THSD modem enabled and de-select the ignore escape sequence check box.■Set Power Up State to THSD transparent mode.8. Open the data form and in the serial communications tab:■In the serial communications setup field set the THSD transparent mode baud rate to 9600, the Flow control to None and the data port to the required data port.■Ensure hardware flow control is set to None.9. Open the data form RF modems tab. The FFSK modem settings do not apply and can be ignored. In the THSD modem section set up the following:■Wide band modem enabled■Layer 2 Protocol enabled■Forward Error Correction disabled■THSD Lead-In Delay default of 30ms is acceptable.10. Program the receiver.7.5.9 VerificationIn order to verify the correct operation as an RF modem a basic functional test can be carried out by sending data between the TB7100 base station and a TM8000 mobile radio.The following equipment will be required:■DC power supply■antenna for receiver input■dummy load for transmitter output■a PC running the terminal application connected to the serial data port on the base station with a 9-pin serial cable■a second PC running the terminal application connected to a TM8000 mobile radio which has been programmed to send and receive the required data modulation (FFSK or THSD).The test setup is shown in “RF modem test setup” on page 101.
 TB7100 Installation and Operation Manual Preparation for Operation 101© Tait Electronics Limited December 2005The correct operation of the base station as an RF modem can be verified by transferring text files between the two PCs. 7.6 Data RepeaterIn data repeater mode the base station will transmit all valid received data.Figure 7.7 RF modem test setupReceiverTransmitter System Interface TerminalApplicationDummy LoadAntennaTerminalApplicationTM8000 MobileRadioPROG/MIC Tx/Rx CHANNEL POWER Tx BUSY F1 F3 F4F2 VOLUMEFigure 7.8 Data repeaterReceiver TransmitterSystem InterfaceRF In RF OutRx DataTx Data
 102 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20057.6.1 Link Settings Remove the cover as detailed in “Removing the Base Station and Opening the Tray” on page 54 and set the following links on the SI board.Links of the mandatory settings must be in the position indicated. Links of the optional settings must be in one of the positions listed. The defaults are generally recommended.Replace the cover as detailed in “Final Reassembly” on page 63.Table 7.7 Data repeater—mandatory settingsLINK Name Pins Position Function CommentsJ221 RS232 Loop Back 3 2-3 RS-232 looped backJ400 Tx Key Source 3 1-2 External Tx key source Use this setting because the transmitter will automatically key up when there is data to send so should not be keyed by the receiver gate.Table 7.8 Data repeater—optional settingsLINK Name Pins Position Function CommentsJ206 Fan Control 1 3 1-22-3 Fan controlled by J207Fan always on Default position is 1-2J207 Fan Control 2 3 2-3 Fan temperature-controlled Do not use position 1-2 (Tx key-activated fan). The transmitter will automatically key up when there is data to send. This will not activate the Tx key line and therefore will not activate the fan.
 TB7100 Installation and Operation Manual Preparation for Operation 103© Tait Electronics Limited December 20057.6.2 Applying PowerBefore turning on the base station, check that:■all looms and cables at the front and rear of the base station are fitted correctly■all connectors are secure■the 20A fuse is fitted.Turn on the power supply and check that the base station powers up correctly:■The power LED on the user interface lights up.■The LCD indicates the current channel number.7.6.3 ProgrammingPlease see the line-controlled base “Programming” on page 82 for details on how to program the base station for RF modem operation.7.6.4 Audio Level AdjustmentIn this configuration the system interface connector is not used, so it is not necessary to set the line level or line Sensitivity.Figure 7.9 System interface link positionsJ400J500 J502J503 J501J221
 104 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20057.6.5 Data Repeater Functional TestingIn order to verify the correct operation as a data repeater a basic functional test can be carried out. This involves sending data from one TM8000 mobile radio to another TM8000 through the TB7100 base station.The following equipment will be required:■DC power supply■antenna for receiver input■dummy load for transmitter output■two TM8000 mobile radios capable of sending and receiving the required data format.■two PCs running the terminal application.■programming cables for the TM8000 mobile radios.The test set-up is shown in Figure 7.10 on page 104. The correct operation of the base station as an RF modem can be verified by transferring text files between the two PCs.7.7 TaitNet TrunkingThe TB7100 base station can be configured to work with a T1810 or T1711 to form part of a TaitNet MPT1327 Trunking System.For more information, refer to the technical note TN-1033-AN “Using the Tait TB7100 in TaitNet MPT1327 Trunked Networks” available from http://support.taitworld.com.Figure 7.10 Data repeater test setupReceiverTransmitter System InterfaceDummy LoadAntennaTM8000 MobileRadioPROG/MIC Tx/Rx CHANNEL POWER Tx BUSY F1 F3 F4F2 VOLUMETM8000 MobileRadioTerminalApplication TerminalApplication
 TB7100 Installation and Operation Manual Preparation for Operation 105© Tait Electronics Limited December 20057.8 Programmable FeaturesThe programmable features are applied to the transmitter and receiver modules by using the TB7100 programming application. 7.8.1 Connecting to the PC1. Plug the TPA-SV-006 or T2000-A19 programming lead into the RS-232 serial port on a PC. Note A USB-to-RS-232 adaptor can be used if the PC does not have a built in serial port.2. Connect the TMAA20-04 adaptor cable (RJ12 socket to RJ45 plug) to the RJ12 plug on the TPA-SV-006 or T2000-A19 programming lead.3. Plug the RJ45 plug on the TMAA20-04 adaptor cable into the PROG/MIC connector located on the front panel of the base station. Select whether the TB7100 programming application communicates with the transmitter or receiver module by using the receiver/transmitter programming switch located on the user interface next to the PROG/MIC connector.7.8.2 TB7100 Programming Application The TB7100 programming application allows the configuration parameters of receiver or transmitter to be read out of a module, edited and written back into the module. It is also possible the save the data files, so if a module ever needs to be replaced, the previously saved data file can be programmed into the new module. The model toolbar, indicates whether the data file is for a receiver or transmitter module.Appearance The TB7100 programming application has been optimised for mouse navigation. Most features can be easily enabled and configured using a check box or drop down list and the frequencies for each channel are simply typed into a table.
 106 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Separate Data Files The base station has separate transmitter and receiver modules, which are independently programmed with their required settings. This means that the base station will have two data files, one for the transmitter and one for the receiver.New Data Files  The reset to defaults feature in the TB7100 programming application makes it easy to create a new data file. The required module type (receiver or transmitter) is selected by pressing the appropriate button on the radio model toolbar. The reset to defaults feature under the file menu is used to reset all the settings to their default states. This ensures all the mandatory and recommended settings are correct before starting to create a new data file. The customer-specific settings for the current application are entered. reset to defaults only affects the currently active radio model, so the correct radio model must be selected first. If “reset to defaults” is greyed out, then the settings are already in their default states.Existing Data Files An existing data file can be read out of a transmitter or receiver module or loaded from file. The radio model toolbar in the TB7100 programming application will automatically update when a data file is loaded or read out of a module to indicate whether the file is for a receiver or transmitter module. The file can then be edited and saved or programmed back into the module.Note It is possible to read the receiver module and then the transmitter module and have both data files loaded at the same time. The radio model toolbar can then be used to toggle between the two data files.When editing is complete, it is important to ensure the receiver/transmitter programming switch position matches the currently active data file before programming the module.Feature FunctionMenus Located along the top of the screen, these allow the user to perform functions such as opening or saving data files, and reading or programming the modules.Toolbar Located just below the menu bar, the toolbar allows easy access to the most commonly used menu items.Radio Model Toolbar Located just below the toolbar, this indicates whether a newly loaded file type is for a receiver or transmitter module. It also allows the required module type to be selected when a new data file is being created.Forms Tree Located on the left side of the screen, the Forms Tree lists all the forms that are available for editing.Forms Displayed beside the Forms Tree is the Active Form. The TB7100 programming application is made up of several Forms (a page of parameters). All the configuration parameters related to a particular feature are grouped together in one form. Each form is intuitively labelled and easily accessible from a Forms Tree
 TB7100 Installation and Operation Manual Preparation for Operation 107© Tait Electronics Limited December 20057.8.3 Mandatory SettingsThe mandatory settings must not be changed from their default states or the base station will not operate correctly. The mandatory settings in the receiver module are not the same as those in the transmitter module. The reset to defaults feature in the TB7100 programming application will ensure all mandatory settings are correct for the selected module type. The mandatory settings are not locked out. It is possible to change a mandatory setting from its required state.Receiver Mandatory Settings The mandatory settings for the receiver are shown below. If these change, the receiver will no longer operate.Form Tab Item Name SettingData General Output SDMs Automatically DisabledData Serial Communications Data_Port AUXData Serial Communications XON_Character 11Data Serial Communications XOFF_Character 13Basic Settings Basic Network Settings TX Timer Duration 1Basic Settings Basic Network Settings TX Lockout Duration 250Basic Settings Sub Audible Signalling CTCSS Lead Out Delay 0Basic Settings Sub Audible Signalling Invert Tx DCS DisabledBasic Settings Sub Audible Signalling DCS Lead Out Delay 0Channels Detailed TX_Frequency 000.000000Channels Detailed TX Sig noneChannels Detailed Power offUI Preferences User Interface Confidence Tones DisabledUI Preferences User Interface Silent Mode DisabledUI Preferences Audible Indicators Enabled All DisabledStartup Startup Power On Mode Power onStartup Startup Reset On Error EnabledPTT MIC PTT PTT Priority highPTT MIC PTT Audio Source CH MICPTT External PTT 1 PTT Transmission Type nonePTT External PTT 1 PTT Priority mediumPTT External PTT 1 Audio Source CH MIC
 108 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Transmitter Mandatory Settings The mandatory settings for the transmitter are shown below, if these change the transmitter will no longer operate.7.8.4 User-defined SettingsThe user-defined settings are specific to the customers application. These are the only settings that need to be changed when configuring a base station for operation. To set up a basic voice repeater or base station only the channel information needs to be entered:■frequency■power level■bandwidth ■squelch threshold■sub-audible signalling.If the system is to be used for data then the data parameters also need to be set correctly:■baud rate■flow control■error correction.Form Tab Item Name SettingData General Output SDMs Automatically DisabledData Serial Communications Data_Port AUXData Serial Communications XON_Character 11Data Serial Communications XOFF_Character 13Basic Settings Sub Audible Signalling Invert Rx DCS DisabledChannels Detailed RX_Frequency 000.000000Channels Detailed RX Sig noneChannels Detailed Squelch hardUI Preferences User Interface Confidence Tones DisabledUI Preferences User Interface Silent Mode DisabledUI Preferences Audible Indicators Enabled All DisabledStartup Startup Power On Mode Power onStartup Startup Reset On Error EnabledPTT MIC PTT PTT Priority highPTT MIC PTT Audio Source CH MicPTT External PTT 1 PTT Priority mediumPTT External PTT 1 Audio Source Audio Tap In
 TB7100 Installation and Operation Manual Preparation for Operation 109© Tait Electronics Limited December 2005Receiver User-defined Settings The user-defined settings for the receiver are shown below. The cells in grey denote that the value should stay as detailed because of other constraining settings.Form Tab Item Name Value Range RecommendedData General Transparent Mode Enabled Enabled / Disabled EnabledData General THSD_Modem_Enabled Enabled / Disabled EnabledData Serial Communications FFSK_Transparent_Mode_Baudrate 1200, 2400, 4800, 9600, 14400, 19200, 28800 19200Data Serial Communications THSD_Transparent_Mode_Baudrate 1200, 2400, 4800, 9600, 14400, 19200, 28800 19200Basic Settings Basic Network Settings Squelch Detect Type Noise level, Signal strength Noise LevelBasic Settings Sub Audible Signalling Invert Rx DCS Enabled, Disabled DisabledChannels Detailed RX_Frequency 000.000000…999.999999  000.000000Channels Detailed RX Sig CTCSS tone OR DCS tone noneChannels Detailed Network 1…4 1Channels Detailed Bandwidth 12.5, 20, 25 12.5Channels Detailed Squelch country, city, hard cityChannels Detailed Use_Channel_For_Data Enabled, Disabled DisabledKey Settings Key 1 Key Action see Key Action type noneKey Settings Key 2 Key Action see Key Action type noneKey Settings Key 3 Key Action see Key Action type noneKey Settings Key 4 Key Action see Key Action type noneUI Preferences User Interface Backlight Mode off, activity, continuous offUI Preferences User Interface Backlight Duration 0…15 5PTT MIC PTT PTT Transmission Type none, voice, data none
 110 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Transmitter User-defined Settings The user-defined settings for the transmitter are shown below. The cells in grey denote that the value should stay as detailed because of other constraining settingsForm Tab Item Name Value Range TxData General Transparent Mode Enabled Enabled / Disabled EnabledData General THSD_Modem_Enabled Enabled / Disabled EnabledData Serial Communications FFSK_Transparent_Mode_Baudrate 1200, 2400, 4800, 9600, 14400, 19200, 28800 19200Data Serial Communications THSD_Transparent_Mode_Baudrate 1200, 2400, 4800, 9600, 14400, 19200, 28800 19200Basic Settings Basic Network Settings TX Timer Duration 0…250 0Basic Settings Basic Network Settings TX Lockout Duration 0…250 0Basic Settings Sub Audible Signalling CTCSS Lead Out Delay 0…1000 0Basic Settings Sub Audible Signalling Invert Tx DCS Enabled, Disabled DisabledBasic Settings Sub Audible Signalling DCS Lead Out Delay 0…1000 0Channels Detailed TX_Frequency 000.000000…999.999999  See Note 1Channels Detailed TX Sig CTCSS tone OR DCS tone noneChannels Detailed Power off, very low, low, medium, high highChannels Detailed Network 1…4 1Channels Detailed Bandwidth 12.5, 20, 25 12.5Channels Detailed Use_Channel_For_Data Enabled, Disabled DisabledKey Settings Key 1 Key Action see Key Action type noneKey Settings Key 2 Key Action see Key Action type noneKey Settings Key 3 Key Action see Key Action type noneKey Settings Key 4 Key Action see Key Action type noneUI Preferences User Interface Backlight Mode off, activity, continuous offUI Preferences User Interface Backlight Duration 0…15 5PTT MIC PTT PTT Transmission Type none, voice, data VoicePTT External PTT 1 PTT Transmission Type none, voice, data Voice
 TB7100 Installation and Operation Manual Preparation for Operation 111© Tait Electronics Limited December 2005ReceiverDigital IO The user-defined settings for the receiver digital IO are shown below. The cells in grey denote mandatory settings.TransmitterDigital IO The user-defined settings for the transmitter digital IO are shown below. The cells in grey denote mandatory settings.Receiver Audio The user-defined settings for the receiver audio IO are shown below. The cells in grey denote mandatory settings.Pin Direction Label Action Active Debounce Signal State Mirrored ToAUX_GPI1 Input BIN_0 BCD_Pin_0 Low 10 None NoneAUX_GPI2 Input BIN_1 BCD_Pin_1 Low 10 None NoneAUX_GPI3 Input BIN_2 BCD_Pin_2 Low 10 None NoneAUX_GPIO4 Input BIN_4 BCD_Pin_3 Low 10 None NoneAUX_GPIO5 None RX_DO_1 No Action Low None None NoneAUX_GPIO6 None RX_DO_2 No Action Low None None NoneAUX_GPIO7 Output RXGATE Busy Status High None None NonePin Direction Label Action Active Debounce Signal State Mirrored ToAUX_GPI1 Input BIN_0 BCD_Pin_0 Low 10 None NoneAUX_GPI2 Input BIN_1 BCD_Pin_1 Low 10 None NoneAUX_GPI3 Input BIN_2 BCD_Pin_2 Low 10 None NoneAUX_GPIO4 Input BIN_4 BCD_Pin_3 Low 10 None NoneAUX_GPIO5 None TX_DO_1 No Action Low None None NoneAUX_GPIO6 None TX_DO_2 No Action Low None None NoneAUX_GPIO7 Input TXKEY External PTT 1High 2None NoneRx/PTT Type Tap In Tap In Type Tap In Unmute Tap Out Tap Out Type Tap Out UnmuteRx None A-Bypass In On PTT R4 D-Split Busy detect + SubaudMic PTT None A-Bypass In On PTT None C-Bypass Out On PTTEPTT1 None A-Bypass In On PTT None C-Bypass Out On PTTEPTT2 None A-Bypass In On PTT None C-Bypass Out On PTT
 112 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Transmitter Audio The user-defined settings for the transmitter audio IO are shown below. The cells in grey denote mandatory settings.7.8.5 Recommended SettingsRecommended settings provide system designers with an extra level of flexibility to meet a specific operational requirement. In general, recommended settings should not be changed from the recommended default value. However unlike mandatory settings, the user is permitted to make changes, providing they verify the correct operation of the enabled or modified feature.No guarantee is given that a feature will work if the recommended settings disable the feature, or if a recommended value is changed.Although the individual modules are capable of these features, they cannot be fully supported by the base station because of its two-module configuration. A few examples of features that are not fully supported by the base station are:■selcall ■two tone ■emergency mode ■scanning■encryption (voice inversion).The reset to defaults feature in the TB7100 programming application will ensure all recommended settings are in their recommended default state. Recommended Settings Examples To explain recommended settings more clearly, two Selcall examples are given below. The first example shows that, although Selcall is not a supported feature of the base station, systems designers have much more flexibility to meet a customer’s requirement.Example One A customer has a requirement to remotely turn on external lighting at the base station site.Although Selcall is not a supported feature of the base station, it is likely that enabling Selcall in the receiver could meet this customer’s requirement. With Selcall enabled, a control status could be programmed to turn on a Rx/PTT Type Tap In Tap In Type Tap In Unmute Tap Out Tap Out Type Tap Out UnmuteRx None A-Bypass In On PTT None D-Split On PTTMic PTT None A-Bypass In On PTT None C-Bypass Out On PTTEPTT1 T8 A-Bypass In On PTT None C-Bypass Out On PTTEPTT2 None A-Bypass In On PTT None C-Bypass Out On PTT
 TB7100 Installation and Operation Manual Preparation for Operation 113© Tait Electronics Limited December 2005Programmable I/O line. This line could be connected to the lighting control circuit at the site via the system interface connector.Example Two The customer also wants an acknowledgement sent back to confirm that the command to turn on the lights was received.At first the solution would appear to be to enable Selcall auto acknowledgments. However this would not work, because the base station has separate receiver and transmitter modules. The receiver module will decode the selcall and enable the I/O line, but has no method of informing the transmitter to send back an acknowledgment. In fact the receiver module would attempt to transmit the acknowledgment itself, but would be inhibited by other mandatory settings.7.8.6 Function KeysThe base station also has four user-defined function keys on the user interface, and programmable digital input and output lines on the system connector.The tables below list the options that can be assigned to the function keys and the digital input and output lines. The grey cells can be programmed but are not recommended (see “Recommended Settings” on page 112).Function Key OptionsNone Monitor / Squelch OverrideAudible Indicators Volume Network Preset Calls Action Digital Output Line  Nuisance DeleteBacklighting Timer  Phone Patch Call Request / ReleaseBacklighting Toggle Preset ChannelBacklighting Timer / Toggle Public AddressCall Cleardown Quiet Operation Channel Preset Call  Repeater Access Tone Tx Emergency Mode Repeater Talkaround Encryption Reset Monitor Group Scanning Activity Reset Monitor / Call CleardownIgnore Two-Tone Silent Operation Keypress Tones Toggle  Single In-Band ToneKeypress Tones Volume  Squelch Override Low Power Transmit Scanning / Nuisance DeleteMonitor
 114 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Digital Input Line ActionsNo Action  Preset Channel Toggle Stand-by Mode  Mute External Audio Input Power Sense (Ignition)  Mute Audio Output Path Enter Emergency Mode  Unmute Audio Output PathSend Channel Preset Call  Send Mic Audio To Spkr Send Network Preset Call 1 Force Audio PA On External PTT 1 and 2  Force Audio PA Off Inhibit PTT  Simulate F1 to F4 Key Toggle Tx RF Inhibit  Toggle F1 to F4 Key LED Decrement Channel  Toggle Alarm Mode Increment Channel  Activate THSD Modem Home Channel  RTS Control (DCE) BCD Pin 0 to 4 Digital Output Line ActionsNo Action  Signalling Audio Mute Status Busy Status  SIBT Received Radio Transmission Status  Monitor Status Channel Lock Status  Hookswitch Status Reflect PTT Status  Call Setup Status External Alert 1 and 2  Control Status Rx (Line 1 to 3) Public Address Status  Radio Stunned Serial Data Tx In Progress  F1 to F4 Key Status Reflect PTT Inhibit Status  FFSK Data Received Status Reflect THSD Modem Status CTS Control (DCE)
 TB7100 Installation and Operation Manual Preparation for Operation 115© Tait Electronics Limited December 20057.9 Additional SettingsThe additional link settings control the following functions:■subaudible signalling■CTCSS (continuous tone controlled squelch system) ■DCS (digital coded squelch)■soft off (tx tail time)■tone on idle■fan operation■channel ID■relay polarity■channel increment and decrement by function buttons■CWID (carrier wave identification).7.10 Adding Subaudible SignallingThe base station is able to decode one CTCSS or DCS tone per channel. It can also generate one CTCSS or DCS tone per channel. The generated tone can be the same as the received tone or can be a different tone. 7.10.1 Enabling Subaudible SignallingTransmitter Module 1. Read the data file out of the transmitter module. Figure 7.11 System interface link positionsJ206RV200J207W401RV401W402J401W302W300W301RV400 J222
 116 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20052. Open the channels form and select the required tone in the Tx Sig column.3. Open the Networks > Basic Settings > Subaudible Signalling tab and configure the subaudible signalling settings (the defaults are suitable for most applications).4. Program the new settings into the transmitter.Receiver Module 1. Read the data file out of the receiver module. 2. Open the channels table and select the required tone in the Rx Sig column.3. Open the Networks > Basic Settings > Subaudible Signalling tab and configure the subaudible signalling settings (the defaults are suitable for most applications).4. The Rx tap out point in the receiver (Programmable I/O audio tab) must be changed to R5. This means that a incoming tone/code is filtered out by the receiver. 5. Program the new settings into the receiver.7.10.2 Testing Subaudible SignallingBefore carrying out these tests, the base station must be configured as a line-controlled base. It must also be connected to the test equipment as described in “Test Equipment Setup” on page 79.Tx Subaudible Signalling Deviation 1. Set up the test set to measure the modulation level and frequency.2. Ensure the test set audio output is turned off, or disconnect the CTU audio input from the test set.3. Activate the Tx Key switch on the CTU.4. Verify that the measured frequency and deviation of the CTCSS match the programmed settings.Note If the measured value does not agree with the programmed set-tings, the transmitter module is either faulty or needs recalibrating.Rx Subaudible Signalling Decode 1. Connect the balanced audio output from the CTU to the audio input port on the test set.2. Set up the test set to measure the audio level and distortion.3. Set the RF signal generator to the correct RF frequency, modulated with a 1kHz audio tone at 60% of full system deviation.
 TB7100 Installation and Operation Manual Preparation for Operation 117© Tait Electronics Limited December 20054. Set the RF output level to -70dBm.5. Verify that the busy LED on the front panel of the base station turns on but the Rx gate LED on the CTU does not turn on, and no audio output is detected from the balanced line output.6. Modulate the carrier with the required subaudible signalling.7. Verify that the Rx gate LED on the CTU turns on, and that the 1kHz audio tone is detected by the test set, and that the measured distortion level is within the receiver specifications.8. Turn off the subaudible signal and check that the audio output mutes again.Note If high distortion is measured, it is likely that the subaudible signal is not being filtered out. Verify that the receiver is programmed with the correct audio tap out point.7.10.3 Multiple Subaudible TonesThe base station cannot decode multiple subaudible tones on a single channel. This can be overcome by two methods:Method 1 1. Third-party equipment is available that can be connected to the base station to perform the decoding and regeneration of multiple tones.2. The base station repeater can be configured to simply pass through any subaudible tone. Method 2 1. The receiver must not be programmed with any subaudible tones in the channel table.2. The Rx tap out point in the receiver (Programmable I/O audio tab) must be left as the default value of R4. This means that a incoming tone/code is not filtered out by the receiver. 3. The transmitter must be programmed not to generate any subaudible tones. 4. The Tx Tap In point in the transmitter (Programmable I/O audio tab) must be left as the default value of T8. This means that a incoming tone/code is not filtered out by the transmitter and will be re-transmitted.Potential Problems 1. The Rx gate may close before end of reverse tone burst (RTB). This means the re-transmitted RTB may be shorter than incoming RTB. A Tx tail (soft off) should be added to overcome this. 2. There is no security for repeaters, as any on-frequency transmission will be repeated, even if it has no subaudible tone.
 118 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20057.11 Soft Off (Tx Tail Time)If subaudible signalling is used, a Tx tail time can be added using the Networks > Basic Settings > Subaudible Signalling tab. A lead out delay can be entered in the appropriate field. 7.11.1 Link Settings Remove the cover as detailed in “Removing the Base Station and Opening the Tray” on page 54 and set the jumper positions on the system interface to match the table below. Replace the cover as detailed in “Final Reassembly” on page 63. Refer to Figure 7.11 on page 115 for the link location.Note When link W302 is fitted, resistor R300 must be fitted.However, if subaudible signalling is not used, adding a lead out delay will have no effect. If soft off operation is still required, a Tx tail time can be created by:1. Linking AUX_GPIO6 and AUX_GPIO7 of the transmitter with link W302 on the system interface as above.2. Adding the following to the default Tx configuration:■AUX_GPIO6 >Direction = input■AUX_GPIO6 >Action = External PTT 2■AUX_GPIO6 >Active = High■AUX_GPIO6 >Debounce = 200 (or smaller if desired)■External PTT (2) > Transmission Type = None.Note A maximum of 200 ms tail time can be achieved using this method.7.12 Tone On Idle (TOI)The tone on idle provides a tone that can be used for indicating when the base station is not transmitting or receiving. The links to enable or disable the tone on idle are shown in the table below. Both links must be in for the TOI to work.Table 7.9 Soft off—link settingsLINK Name Pins Position Function CommentsW302 TX_Key to TX_GPIO6 link 2 FittedNot fitted When fitted this allows two external PTT to control the transmitter; used for soft off modeDefault is fitted
 TB7100 Installation and Operation Manual Preparation for Operation 119© Tait Electronics Limited December 20057.12.1 Link Settings Remove the cover as detailed in “Removing the Base Station and Opening the Tray” on page 54 and set the jumper positions on the system interface to match the table below. Replace the cover as detailed in “Final Reassembly” on page 63. Refer to Figure 7.11 on page 115 for the link location.The potentiometers for the tone on idle adjustments shown in the table below can be found on the system interface module. Refer to Figure 7.11 on page 115 for the potentiometer location.Table 7.10 Ton on idle (TOI)—link settingsLINK Name Pins Position Function CommentsW401 TOI 9V Enable 2 FittedNot fitted Tone on Idle enableTone on Idle disable Default is fittedW402 TOI 4.5V Enable 2 FittedNot fittedTone on Idle oscillator enableTone on Idle oscillator disableDefault is fittedPotentiometer FunctionRV400 Frequency adjustRV401 level adjust
 120 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20057.13 Fan OperationThe fans can be made to operate in three modes:■continuous■on when base station transmits■on at a set temperature.The fan operation can be set as shown in the table below.7.13.1 Link Settings Remove the cover as detailed in “Removing the Base Station and Opening the Tray” on page 54 and set the jumper positions on the system interface to match the table below. Replace the cover as detailed in “Final Reassembly” on page 63. Refer to Figure 7.11 on page 115 for the link location.Table 7.11 Fan operation—link settingsLINK Name Pins Position Function CommentsJ206 Fan Control 1 3 1-22-3 Fan controlled by J207Fan always on Default position is 1-2J207 Fan Control 2 3 1-22-3 Fan Tx key-controlledFan temperature-controlled Default position is 2-3Figure 7.12 System interface link positionsJ400J500 J502J503 J501J221
 TB7100 Installation and Operation Manual Preparation for Operation 121© Tait Electronics Limited December 2005The temperature threshold is set at the factory to 40°C. The potentiometer and test point to adjust the temperature threshold can be found on the system interface module. Refer to Figure 7.11 on page 115 for the location.When adjusting the temperature threshold the fans must be off. The temperature threshold to voltage relationship is shown in Figure 7.13 on page 121.Important When using THSD and the user interface PTT, the fan set-ting should be temperature controlled or always on. This is because the user interface PTT line does not toggle the TX-key line on the system interface and the THSD is only on for short burst of time never allowing the fan time to spin up.Designator FunctionRV200 temperature threshold adjustJ222 test point for temperature thresholdFigure 7.13 temperature threshold to voltage relationship0.92 0.98 1.04 1.10 1.16 1.22 1.28 1.34 1.40 1.46 1.520102030405060708090VoltageTemperature50688610412214015817619432FahrenheitCelsius
 122 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20057.14 Channel IDChannel ID can be enabled using the links as below.7.14.1 Link Settings Remove the cover as detailed in “Removing the Base Station and Opening the Tray” on page 54 and set the jumper positions on the system interface to match the table below. Replace the cover as detailed in “Final Reassembly” on page 63. Refer to Figure 7.11 on page 115 for the link location.Note When link W300 is fitted, resistor R304 must be fitted.When link W301 is fitted, resistor R302 must be fitted.When Tx/Rx digital input 1-4 are used for channel selection only 16 binary or 10 BCD channels are available.When Tx/Rx digital input 1-4 and another line, made from the shorting of Tx digital in/out 1 and Rx digital in/out 1 on the system interface connecter are used then a total of 32 binary or 20 BCD channels are selectable. Requires link W300 to be fitted.Table 7.12 Channel ID—link settingsLINK Name Pins Position Function CommentsW300 2 FittedNot fitted When fitted this allows both transmit and receive modules to be controlled by the same external digital IO lines, used for BCD; used with W301Default is fittedW301 2 FittedNot fitted When fitted this allows both transmit and receive modules to be controlled by the same external digital IO lines; used with W300Default is fitted
 TB7100 Installation and Operation Manual Preparation for Operation 123© Tait Electronics Limited December 20057.15 Relay PolarityRelay operation can be configured to be energised when the receiver gate is active or inactive.7.15.1 Link SettingsRemove the cover as detailed in “Removing the Base Station and Opening the Tray” on page 54 and set the jumper positions on the system interface to match the table below. Replace the cover as detailed in “Final Reassembly” on page 63. Refer to Figure 7.11 on page 115 for the link location.7.16 Channel Increment and Decrement by Function KeysFunction button one and two can be configured to increment and decrement the channels. This requires two links fitted to the rear of the user interface board, this will hard wire the F1 and F2 buttons to the increment/decrement function. It is recommended F1 & F2 have no other programmed action.This option will allow all 99 channels to be selected from the function buttons. For more information, refer to the technical note TN-1032-AN “Implementing Channel Increment and Decrement on the TB7100” available from http://support.taitworld.com.Table 7.13 Relay polarity—link settingsLINK Name Pins Position Function CommentsW401 Relay Polarity Control 31-22-3Energised for receiver active gateEnergised for receiver inactive gateDefault is 1-2
 124 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 20057.17 Carrier Wave Identification (CWID)CWID is a morse identification feature that can be setup using the TB7100 programming application.7.17.1 Station IDCan contain a preprogrammed station ID of up to 16 characters in length. The user may wish to prefix the letters DE before the message, meaning “from”.7.17.2 Station ID 2/MessageCan contain a second preprogrammed station ID or a message of up to 130 characters.7.17.3 Tone FrequencyThe Morse tone frequency is programmable from 1Hz to 3000Hz in one cycle increments. FCC rules state that the frequency shall be 800Hz to 1200Hz.7.17.4 ID Repeat TimeA programmable repeat time from 1 to 99 minutes. This allows the user to program how often the ID or message is sent. Setting the output control to “After PTT” will cause the ID message to be sent following the last activation of the COR/COS/CTCSS, Inhibit or PTT inputs, provided the time is met that is programmed in this register.7.17.5 Speed (Words per Minute)The speed is programmable from 1 to 99 words per minute (WPM).7.17.6 Wait Period after Loss of COR/COS/CTCSS Input Before IDingThis register allows from 1 to 99 seconds of delay before the Morse ID will transmit after COR/COS/CTCSS loss assuming the repeat interval in ID Repeat Time has expired.7.17.7 Transmit Key-Up DelayProgrammable key-up delay from 0.0 to 9.9 seconds. This allows for a front porch delay time before the ID or message is sent. This gives receiving units
 TB7100 Installation and Operation Manual Preparation for Operation 125© Tait Electronics Limited December 2005with CTCSS decoders time to un-squelch before any Morse code is transmitted.7.17.8 Transmit Time Out TimeIf programmed to 0 this function is off. Programming from 1 to 999 seconds will set the repeater to drop out after the number of seconds programmed in this register. The time out timer is designed to limit conversation length.7.17.9 Transmit PTT Drop Out TimeThis register programs how many seconds the repeater’s transmitter will stay keyed after loss of COR/COS/CTCSS input. Normally this is programmed for 2 to 7 seconds. After PTT In is detected, the ID-1 will turn on its PTT out, as long as the PTT In remains active. After loss of the PTT In, the PTT out will remain active for the programmed period of time before dropping, thus allowing another unit to answer before the repeater drops. The ID-1 must be installed in series with the PTT line (i.e. ID-1 installed at break in station PTT line) for this function to operate.7.17.10 Output ControlSetting the output Control to “After PTT” will cause the ID message to be sent following the last activation of the COR/COS/CTCSS, inhibit or PTT inputs, provided the time is met that is programmed in the register ID repeat time. setting the output control to “continuous” will cause the ID or message to be sent at the expiration of a period equal to the delay time. For example, if register ID repeat time is programmed as 10, the ID or message will be sent every 10 minutes. This will occur during a conversation if one is in progress when the timer goes off.
 126 Preparation for Operation TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005
 TB7100 Installation and Operation Manual Maintenance Guide 127© Tait Electronics Limited December 20058 Maintenance GuideThe base station is designed to be very reliable and should require little maintenance. However, performing regular checks will prolong the life of the equipment and prevent problems from happening. It is beyond the scope of this manual to list every check that you should perform on your base station. The type and frequency of maintenance checks will depend on the location and type of your system. The checks and procedures listed below can be used as a starting point for your maintenance schedule.Performance Checks We suggest you monitor the following operational parameters:■VSWR■DC input voltage, especially on transmit■receiver sensitivity■the setting of the receiver gate opening■transmit deviationThese basic checks will provide an overview of how well your base station is operating.Receiver There are no special maintenance requirements for the receiver.Transmitter There are no special maintenance requirements for the transmitter.System Interface There are no special maintenance requirements for the System interface.Ventilation The base station has been designed to have a front-to-back cooling airflow. We strongly recommend that you periodically check and maintain the ventilation requirements described in “Ventilation” on page 46 to ensure a long life and trouble-free operation for your base station.Cooling Fans The cooling fans have a long service life and have no special maintenance requirements.Battery If you are using battery, you should check the batteries regularly in accordance with the manufacturer’s recommendations.
 128 Maintenance Guide TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005
 TB7100 Installation and Operation Manual Glossary 129© Tait Electronics Limited December 2005GlossaryThis glossary contains an alphabetical list of terms and abbreviations related to the TB7100 base station. For information about trunking, mobile, or portable terms, consult the glossary provided with the relevant documentation.Aaccessory An accessory is an ancillary device fitted externally to a base station, such as an external microphone.active Digital outputs are active when the base station pulls their voltage low and current is flowing. Digital inputs are active when external equipment is pulling them to ground. All base station digital outputs are open collector.ADC Analog-to-Digital Converter.  A device for converting an analog signal to a digital signal that represents the same information.air intake temperature The temperature of the air as measured at the transmitter’s air intake.anti-kerchunking Anti-kerchunking is a base station feature that discourages users from “pinging” (kerchunking) the repeater with short bursts of RF. audible indicators The radio’s audible indicators are used in combination with visual indicators to provide feedback to the radio user. Types of audible indicators are incoming call tones, warning tones, confirmation tones, keypress confidence tones and signalling sidetones.Bbacklighting The radio’s display or keypad lights up when there is activity on the radio, such as when a key is pressed or when a call is received. The value of the backlighting timer and how backlighting was activated determine how long backlighting remains on.backlighting timer The backlighting timer determines how long backlighting remains on once it is activated.
 130 Glossary TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005balanced line A balanced line has two wires carrying equal and opposite signals. It is typically used in a line-connected base station for connecting to the despatcher console. The system interface identifies the balanced line out as Rx line output + and Rx line output -, and the balanced line in as Tx line input + and Tx line input -.base station A base station is a tray containing transmitter, receiver and system interface modules. BCD BCD (binary coded decimal) is a code in which a string of four binary digits represents a decimal number.birdie A birdie is a desensitised channel caused by internal interference. A birdie can be eliminated by activating a birdie killer on the channel.birdie killer A birdie killer is an internal circuitry switch that greatly reduces the effect of a birdie on a channel.brownout A dip in the supply voltage sufficient to put the control section into hardware reset.CCalibration Application The Calibration Application is a utility for calibrating various parts of the receiver and transmitter circuitry.CCDI2  CCDI2 (computer controlled data interface version 2) is a proprietary Tait command protocol used between computer equipment and a Tait radio. The TB7100 base station does not support CCDI2.CCI  CCI (computer controlled interface) is a proprietary Tait command protocol used between computer equipment and a Tait radio.channel A channel is a frequency pair (or just a single frequency in a simplex system).Note: Different channels may have identical frequencies, while other operating parameters may be different.channel profile A channel profile is a named set of configuration items relating to the base station’s RF configuration, transmitter power output and power saving modes. Like the signalling profile, it can be applied to any channel. Together, these profiles define most configuration items.channel spacing Channel spacing is the frequency difference between adjacent channels. channel table The channel table is the base station’s database of channel configurations.
 TB7100 Installation and Operation Manual Glossary 131© Tait Electronics Limited December 2005city squelch When a radio’s noise mute threshold is programmed for city squelch, the radio is less sensitive to interference than if programmed for country squelch and so stronger signals are required for the radio’s speaker to unmute.City squelch is also known as local squelch.CODEC An IC which combines analog-to-digital conversion (coding) and digital-to-analog conversion (decoding).configuration file A configuration file consists of all the configuration settings needed for a base station, stored as a file in the configurations folder. Configuration files have the extension *.t7p. The TB7100 uses two files, one for the receiver and one for the transmitter.country squelch When a radio’s squelch threshold is programmed for country squelch, the radio is more sensitive than if programmed for city squelch and so the radio’s speaker unmutes more readily. When programmed for country squelch, the radio can be used in areas where the signal may be weak and where maximum range is desirable.Country squelch is also known as distant squelch.CTCSS CTCSS (continuous tone controlled squelch system), also known as PL (private line), is a type of signalling that uses subaudible tones to segregate groups of users.CTCSS/DCS filter The CTCSS/DCS filter removes any CTCSS or DCS tones that may be present on the received audio. The filter limits the range of frequencies the radio passes from the incoming signal to the speaker and so in some situations affects signal quality. Filtering can be automatically switched off for channels that do not have CTCSS or DCS.CTU A Calibration Test Unit (CTU) is a device used to assist in making testing and calibration of the TB7100 easier.CWID CWID (Continuous Wave IDentification) is a method of automatically identifying the base station using a Morse code.DDAC Digital-to-Analog Converter. A device for converting a digital signal to an analog signal that represents the same information.data call A data call is a call or part of a call between two radio units that carries data rather than speech communications. A data call can be a status message, short data message or non-prescribed data (NPD) call.DCS DCS (digital coded squelch), also known as DPL (digital private line), is a type of subaudible signalling used for segregating groups of users.  DCS codes are identified by a three-digit octal number, which forms part of the
 132 Glossary TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005continuously repeating code word.  When assigning DCS signalling for a channel, you specify the three-digit code.de-emphasis De-emphasis is a filtering process in the receiver that attenuates higher frequency audio. It restores pre-emphasised audio to its original relative proportions. digital signal processor The device in a radio that analyses and processes signals in the digital domain. Also known as DSP.Duplexer A duplexer is a device for connecting one antenna to a transmitter and receiver at the same time.duty cycle Duty cycle is used in relation to the transmitter. It is the proportion of time (expressed as a percentage) during which the transmitter is keyed. The transmitter can be operated continuously. Eeconomy cycling Economy cycling is the switching between states that occurs when economy mode is active and after there is no valid activity on a channel for a preprogrammed time (the economy mode timer). Economy cycling consists of two states, the receive state and the standby state. The amount of time the radio spends in each state is determined by the economy duty cycle.economy duty cycle The economy duty cycle is the amount of time the radio spends in the receive and standby states during economy cycling.economy mode Economy mode reduces the radio’s power consumption when it is idle. When economy mode is active, and there has been no valid activity on a channel for the duration of the economy mode timer, the radio begins economy cycling.economy mode timer The economy mode timer sets the time between when valid activity was last detected on a channel and the start of economy cycling. EIA Electronic Industries Alliance.  Accredited by the American National Standards Institute (ANSI) and responsible for developing telecommunications and electronics standards in the USA.EMC Electromagnetic Compatibility. The ability of equipment to operate in its electromagnetic environment without creating interference with other devices or being susceptible to disturbance in the presence of other equipment.ETSI European Telecommunications Standards Institute.  The non-profit organisation responsible for producing European telecommunications standards.
 TB7100 Installation and Operation Manual Glossary 133© Tait Electronics Limited December 2005FFFSK FFSK (fast frequency shift keying). In Trunking applications this is the method by which code words are sent over the control channel. In 1200 baud FFSK, a 1200 Hz tone represents a zero and an 1800 Hz tone represents a one.frequency band The range of frequencies that the equipment is capable of operating on.front panel The part of the chassis that has the user interface on it.Full Duplex Full duplex is the action of receiving and transmitting at the same time.function key A function key is a key on a radio or radio accessory that can have functions assigned to it. Ggating Gating is the process of opening and closing the receiver audio path. When a valid signal is received, the receiver audio path opens. GPIO General Purpose Input Output (GPIO) lines are used on the TB7100 to configure it for different modes. Hhysteresis Hysteresis is the difference between the upper and lower trigger points.  For example, the receiver gate opens when the upper trigger point is reached, but will not close until the level falls to the lower trigger point.  An adequate hysteresis prevents the receiver gate from repeatedly opening and closing when the level is about that of the trigger point. Iinactive Digital outputs are inactive if the base station is doing nothing to them. They are floating, open collector outputs. Digital inputs are inactive when they are open circuit. indicator Indicators provide feedback to the radio user on how the current operation is proceeding and on the operating state of the radio. For example, keypress confidence tones are the tones heard when a keypad key or a function key is pressed and tell the user that an action is permitted. Tait radios use combinations of audible indicators and visual indicators.inhibit Prevents the radio state changing.
 134 Glossary TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005isolator An isolator is a passive two-port device which transmits power in one direction, and absorbs power in the other direction. It is used in a PA to prevent damage to the RF circuitry from high reverse power, and reduces the generation of spurious product due to the ingress of signals from other transmitters.Kkerchunking Kerchunking is transmitting for a second or less without saying anything in order to test the base station. This results in a ‘kerchunk’ sound.keypress confidence tone A keypress confidence tone is a type of audible indicators given each time the user presses a key to confirm that the action selected is valid.LLCD A Liquid Crystal Display (LCD) is used on the TB7100 user interface to display channel number.line-controlled base station A TB7100 is a line-controlled base station when it receives audio (sending it out via its systems interface), transmits audio received over its systems interface, and its transmitter is keyed via the Tx Key line.local squelch See city squelch.MMandatory Settings The mandatory settings are settings in the programming application that must not be changed from their default states or the TB7100 will not operate correctly. The Mandatory Settings in the receiver module are not the same as those in the transmitter module.mute A mute controls the circumstances under which a received signal is passed to the radio’s audio output. When a mute is active, the radio’s speaker audio path opens under certain conditions, determined by the type of signalling operating on a channel and the noise mute threshold.Nnoise mute The noise mute feature ensures that the radio’s speaker only unmutes when an intelligible signal is received. A signal is considered intelligible when it is strong enough to exceed a predetermined noise mute threshold.noise mute threshold The noise mute threshold is the level the signal must reach before it is regarded as intelligible and the radio’s mute is opened.
 TB7100 Installation and Operation Manual Glossary 135© Tait Electronics Limited December 20050operating range Operating range is another term for switching range.PPA The PA (power amplifier) is a part of the transmitter that boosts the exciter output to a certain level sufficient to transmit via the antenna.power down Radio is switched off.power up Radio is switched on.pre-emphasis Pre-emphasis is a process in the transmitter that boosts higher audio frequencies. programming manipulating calibration database, radio database.Programming Application The programming application is used to create configuration files for the base station. The programming application can read files from the base station or load new files onto the base station.programming database The programming database is the information that is altered using the radio programming application. For trunked radios, each programming database consists of separate network, fleet and radio information.programming mode The mode of operation of the radio in which computer equipment can read from and write to the radio database.Qquiet operation When quiet operation is active, all audible indicators except incoming call alerts, sidetones and warning tones are disabled. Contrast with silent operation.quiet state The quiet state is the state the radio is in when monitor is inactive the radio user does not have to listen to traffic that is not intended for them.RRecommended Settings Recommended settings are settings in the programming application that should not be changed from the recommended default value, but unlike mandatory settings, the user is permitted to make changes; providing they verify the correct operation of the enabled or modified feature. No guarantee is given that a feature will work if the recommended settings disable the feature or if a recommended value is changed.
 136 Glossary TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005repeater A repeater receives a radio signal and re-transmits it. Use of a repeater increases the coverage area of a two-way radio system and ensures more reliable performance in areas where signals are reflected or attenuated by buildings or terrain.In a repeater-based system, the radio’s transmit frequency is the frequency the repeater is listening on, and the radio’s receive frequency is the frequency the repeater re-broadcasts signals on.receive (Rx) frequency The receive frequency is the frequency that a radio is currently tuned to.reverse tone burst Reverse tone bursts (RTB) can be used with CTCSS. When reverse tone bursts are enabled, the phase of the generated tones is reversed for a number of cycles just before transmission ceases. If the receiver is configured for reverse tone burst, it responds by closing its gate faster than if the RTB were not transmitted.RF RF stands for radio frequency and refers to the part of the electromagnetic spectrum used to transmit radio and television signals.RSSI RSSI (Received Signal Strength Indicator) feature that indicates the strength of the received signal. Rx Rx is an abbreviation for receive or receiver.Ssensitivity The sensitivity of a radio receiver is the minimum input signal strength required to provide a useable output.SINAD SINAD (Signal plus Noise and Distortion) is a measure of signal quality. It is the ratio of (signal + noise + distortion) to (noise + distortion). A SINAD of 12dB corresponds to a signal to noise voltage ratio of 4:1.subaudible signalling Subaudible signalling is signalling that is at the bottom end of the range of audible frequencies. The base station supports CTCSS and DCS subaudible signalling. subtone A subtone (subaudible signalling tone) is a CTCSS tone or a DCS code. switching range The switching range is the range of frequencies that the equipment is tuned to operate on.system interface The system interface is the set of inputs to and outputs from the base station (excluding RF), provided by a module inside the tray.
 TB7100 Installation and Operation Manual Glossary 137© Tait Electronics Limited December 2005TTB7100 Base Station A TB7100 base station consists of the equipment necessary to receive and transmit on one channel. Generally, this means receiver, transmitter and system interface modules. Often abbreviated to TB7100 or base station. TCXO Temperature compensated crystal oscillator (voltage controlled). The frequency reference for the RF part of the radio.Talk Through Repeater A TB7100 is a talk through repeater when its audio path is configured to pass the audio it receives on to the transmitter, and its receiver gate signal is configured to key the transmitter.THSD Tait High Speed Data (THSD) is a proprietary data protocol. THSD uses a four level frequency shift keying modulation scheme.toggle The term toggle is used to describe the switching between two states.TOI Tone On Idle (TOI) is an audio tone used on the receiver output to indicate when the base station is idle.transmit (Tx) frequency The transmit frequency is the frequency that all outgoing transmissions are made on.transmit inhibit The transmit inhibit feature determines under what conditions a transmission request does not result in the radio transmitting.transmit lockout The transmit lockout feature prevents the base station from transmitting for a time once the transmit timer has expired.Tx Tx is an abbreviation for transmit or transmitter.
 138 Glossary TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Uunbalanced line An unbalanced line has one wire earthed. It is typically used for short connections, for example, between a base station and a repeater on the same site. The system interface identifies the wires of unbalanced lines with Rx audio output, Tx audio input, and Ground.User Defined Settings The User Defined Settings are settings in the programming application that are specific to the customers application. These are the only settings that need to be changed when configuring a TB7100 for operation.user interface The user interface panel is an area at the front of the base station with buttons, LEDs and other controls that let you interact with the base station.Vvalid signal A valid signal is a signal that the receiver responds to by opening the receiver gate. A signal is valid for example when it is stronger than a minimum level and when it has the specified subtone.visual indicator The term “visual indicator” refers to a visual cue the radio gives to provide feedback to the user. Visual indicators are used in combination with audible indicators. Visual indicators include LEDs and LCD display text.VSWR Voltage Standing Wave Ratio (VSWR) is the ratio of the maximum peak voltage anywhere on the line to the minimum value anywhere on the line.  A perfectly matched line has a VSWR of 1:1.  A high ratio indicates that the antenna subsystem is poorly matched.WWatchdog A watchdog circuit checks that the system is still responding.  If the system does not respond (because the firmware has locked up), the circuit resets the system.
 TB7100 Installation and Operation Manual 139© Tait Electronics Limited December 2005Tait General Software Licence AgreementThis legal document is an Agreement between you (the “Licensee”) and Tait Electronics Limited (“Tait”). By using any of the Software or Firmware items prior-installed in the related Tait product, included on CD or downloaded from the Tait website, (hereinafter referred to as “the Software or Firmware”) you agree to be bound by the terms of this Agreement. If you do not agree to the terms of this Agreement, do not install and use any of the Software or Firmware. If you install and use any of the Software or Firmware that will be deemed to be acceptance of the terms of this licence agreement.The terms of this Agreement shall apply subject only to any express written terms of agreement to the contrary between Tait and the Licensee.LicenceTAIT GRANTS TO YOU AS LICENSEE THE NON-EXCLUSIVE RIGHT TO USE THE SOFTWARE OR FIRMWARE ON A SINGLE MACHINE PROVIDED YOU MAY ONLY:1. COPY THE SOFTWARE OR FIRMWARE INTO ANY MACHINE READABLE OR PRINTED FORM FOR BACKUP PURPOSES IN SUPPORT OF YOUR USE OF THE PROGRAM ON THE SINGLE MACHINE (CERTAIN PROGRAMS, HOWEVER, MAY INCLUDE MECHANISMS TO LIMIT OR INHIBIT COPYING, THEY ARE MARKED “COPY PROTECTED”), PROVIDED THE COPYRIGHT NOTICE MUST BE REPRODUCED AND INCLUDED ON ANY SUCH COPY OF THE SOFTWARE OR FIRMWARE; AND / OR2. MERGE IT INTO ANOTHER PROGRAM FOR YOUR USE ON THE SINGLE MACHINE (ANY PORTION OF ANY SOFTWARE OR FIRMWARE MERGED INTO ANOTHER PROGRAM WILL CONTINUE TO BE SUBJECT TO THE TERMS AND CONDITIONS OF THIS AGREEMENT).THE LICENSEE MAY NOT DUPLICATE, MODIFY, REVERSE COMPILE OR REVERSE ASSEMBLE ANY SOFTWARE OR FIRMWARE IN WHOLE OR PART.Important NoticeTHE SOFTWARE OR FIRMWARE MAY CONTAIN OPEN SOURCE SOFTWARE COMPONENTS (“OPEN SOURCE COMPONENTS”). OPEN SOURCE COMPONENTS ARE EXCLUDED FROM THE TERMS OF THIS AGREEMENT EXCEPT AS EXPRESSLY STATED IN THIS AGREEMENT AND ARE COVERED BY THE TERMS OF THEIR RESPECTIVE LICENCES WHICH MAY EXCLUDE OR LIMIT ANY WARRANTY FROM OR LIABILITY OF THE DEVELOPERS AND/OR COPYRIGHT HOLDERS OF THE OPEN SOURCE COMPONENT FOR THE PERFORMANCE OF THOSE OPEN SOURCE COMPONENTS. YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF EACH SUCH LICENCE. FOR MORE INFORMATION SEE:http://support.taitworld.com/go/opensourceTitle to Software THIS AGREEMENT DOES NOT CONSTITUTE A CONTRACT OF SALE IN RELATION TO THE SOFTWARE OR FIRMWARE SUPPLIED TO THE LICENSEE. NOT WITHSTANDING THE LICENSEE MAY OWN THE MAGNETIC OR OTHER PHYSICAL MEDIA ON WHICH THE SOFTWARE OR FIRMWARE WAS ORIGINALLY SUPPLIED, OR HAS SUBSEQUENTLY BEEN RECORDED OR FIXED, IT IS A FUNDAMENTAL TERM OF THIS AGREEMENT THAT AT ALL TIMES TITLE AND OWNERSHIP OF THE SOFTWARE OR FIRMWARE, WHETHER ON THE ORIGINAL MEDIA OR OTHERWISE, SHALL REMAIN VESTED IN TAIT OR THIRD PARTIES WHO HAVE GRANTED LICENCES TO TAIT.Term and Termination THIS LICENCE SHALL BE EFFECTIVE UNTIL TERMINATED IN ACCORDANCE WITH THE PROVISIONS OF THIS AGREEMENT. THE LICENSEE MAY TERMINATE THIS LICENCE AT ANY TIME BY DESTROYING ALL COPIES OF THE SOFTWARE OR FIRMWARE AND ASSOCIATED WRITTEN MATERIALS. THIS LICENCE WILL BE TERMINATED AUTOMATICALLY AND WITHOUT NOTICE FROM TAIT IN THE EVENT THAT THE LICENSEE FAILS TO COMPLY WITH ANY TERM OR CONDITION OF THIS AGREEMENT. THE LICENSEE AGREES TO DESTROY ALL COPIES OF THE SOFTWARE OR FIRMWARE AND ASSOCIATED WRITTEN MATERIALS IN THE EVENT OF SUCH TERMINATION.
 140 TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005Limited Warranty THE SOFTWARE OR FIRMWARE (INCLUDING OPEN SOURCE COMPONENTS) IS SUPPLIED BY TAIT AND ACCEPTED BY THE LICENSEE “AS IS” WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT BEING LIMITED TO ANY IMPLIED WARRANTIES AS TO MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. THE LICENSEE ACKNOWLEDGES THAT THE SOFTWARE OR FIRMWARE (INCLUDING OPEN SOURCE COMPONENTS) IS USED BY IT IN BUSINESS AND ACCORDINGLY TO THE MAXIMUM EXTENT PERMITTED BY LAW NO TERMS OR WARRANTIES WHICH ARE IMPLIED BY LEGISLATION SHALL APPLY TO THIS AGREEMENT. TAIT DOES NOT WARRANT THAT THE FUNCTIONS CONTAINED IN THE SOFTWARE OR FIRMWARE (INCLUDING OPEN SOURCE COMPONENTS) WILL MEET THE LICENSEE’S REQUIREMENTS OR THAT THE OPERATION OF THE SOFTWARE OR FIRMWARE (INCLUDING OPEN SOURCE COMPONENTS) WILL BE UNINTERRUPTED OR ERROR FREE.Exclusion of LiabilityIN NO CIRCUMSTANCES SHALL TAIT BE UNDER ANY LIABILITY TO THE LICENSEE, OR ANY OTHER PERSON WHATSOEVER, WHETHER IN TORT (INCLUDING NEGLIGENCE), CONTRACT (EXCEPT AS EXPRESSLY PROVIDED IN THIS AGREEMENT), EQUITY, UNDER ANY STATUTE, OR OTHERWISE AT LAW FOR ANY LOSSES OR DAMAGES WHETHER GENERAL, SPECIAL, EXEMPLARY, PUNITIVE, DIRECT, INDIRECT OR CONSEQUENTIAL ARISING OUT OF OR IN CONNECTION WITH ANY USE OR INABILITY OF USING THE SOFTWARE OR FIRMWARE (INCLUDING OPEN SOURCE COMPONENTS).THE LICENSEE’S SOLE REMEDY AGAINST TAIT WILL BE LIMITED TO BREACH OF CONTRACT AND TAIT’S SOLE AND TOTAL LIABILITY FOR ANY SUCH CLAIM SHALL BE LIMITED AT THE OPTION OF TAIT TO THE REPAIR OR REPLACEMENT OF THE SOFTWARE OR FIRMWARE OR THE REFUND OF THE PURCHASE PRICE OF THE SOFTWARE OR FIRMWARE.GeneralTHE LICENSEE CONFIRMS THAT IT SHALL COMPLY WITH THE PROVISIONS OF LAW IN RELATION TO THE SOFTWARE OR FIRMWARE.Law and Jurisdiction THIS AGREEMENT SHALL BE SUBJECT TO AND CONSTRUED IN ACCORDANCE WITH NEW ZEALAND LAW AND DISPUTES BETWEEN THE PARTIES CONCERNING THE PROVISIONS HEREOF SHALL BE DETERMINED BY THE NEW ZEALAND COURTS OF LAW. PROVIDED HOWEVER TAIT MAY AT ITS ELECTION BRING PROCEEDINGS FOR BREACH OF THE TERMS HEREOF OR FOR THE ENFORCEMENT OF ANY JUDGEMENT IN RELATION TO A BREACH OF THE TERMS HEREOF IN ANY JURISDICTION TAIT CONSIDERS FIT FOR THE PURPOSE OF ENSURING COMPLIANCE WITH THE TERMS HEREOF OR OBTAINING RELIEF FOR BREACH OF THE TERMS HEREOF.No Dealings THE LICENSEE MAY NOT SUBLICENSE, ASSIGN OR TRANSFER THE LICENCE OR THE PROGRAM EXCEPT AS EXPRESSLY PROVIDED IN THIS AGREEMENT. ANY ATTEMPT OTHERWISE TO SUBLICENSE, ASSIGN OR TRANSFER ANY OF THE RIGHTS, DUTIES OR OBLIGATIONS HEREUNDER IS VOID.No Other Terms THE LICENSEE ACKNOWLEDGES THAT IT HAS READ THIS AGREEMENT, UNDERSTANDS IT AND AGREES TO BE BOUND BY ITS TERMS AND CONDITIONS. THE LICENSEE FURTHER AGREES THAT SUBJECT ONLY TO ANY EXPRESS WRITTEN TERMS OF AGREEMENT TO THE CONTRARY BETWEEN TAIT AND THE LICENSEE THIS IS THE COMPLETE AND EXCLUSIVE STATEMENT OF THE AGREEMENT BETWEEN IT AND TAIT IN RELATION TO THE SOFTWARE OR FIRMWARE WHICH SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT, ORAL OR WRITTEN AND ANY OTHER COMMUNICATIONS BETWEEN THE LICENSEE AND TAIT RELATING TO THE SOFTWARE OR FIRMWARE.
 TB7100 Installation and Operation Manual 141© Tait Electronics Limited December 2005Directive 1999/5/EC Declaration of Conformityda DanskUndertegnede Tait Electronics Limited erklærer herved, at følgende udstyr TBBA4A, TBBB1A & TBBH5A overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.Se endvidere: http://eudocs.taitworld.com/de DeutschHiermit erklärt Tait Electronics Limited die Übereinstimmung des Gerätes TBBA4A, TBBB1A & TBBH5A mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG.Siehe auch: http://eudocs.taitworld.com/el ΕλληνικόςΜε την παρουσα Tait Electronics Limited δηλωνει οτι TBBA4A, TBBB1A & TBBH5A συµµορφωνεται προσ τισ ουσιωδεισ απαιτησεισ και τισ λοιπεσ σχετικεσ διαταξεισ τησ οδηγιασ 1999/5/ΕΚ.βλέπε και: http://eudocs.taitworld.com/en EnglishTait Electronics Limited declares that this TBBA4A, TBBB1A & TBBH5A complies with the essential requirements and other relevant provisions of Directive 1999/5/EC. See also: http://eudocs.taitworld.com/es EspañolPor medio de la presente Tait Electronics Limited declara que el TBBA4A, el TBBB1A y el TBBH5A cumplen con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.Vea también: http://eudocs.taitworld.com/fi SuomiTait Electronics Limited vakuuttaa täten että TBBA4A, TBBB1A & TBBH5A tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.Katso: http://eudocs.taitworld.com/fr FrançaisPar la présente, Tait Electronics Limited déclare que l'appareil TBBA4A, TBBB1A & TBBH5A est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.Voir aussi: http://eudocs.taitworld.com/it ItalianoCon la presente Tait Electronics Limited dichiara che questo TBBA4A, TBBB1A & TBBH5A è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.Vedi anche: http://eudocs.taitworld.com/nl NederlandsHierbij verklaart Tait Electronics Limited dat het toestel TBBA4A, TBBB1A & TBBH5A in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/ EG.Zie ook: http://eudocs.taitworld.com/pt PortuguêsTait Electronics Limited declara que este TBBA4A, TBBB1A & TBBH5A está conforme com os requisitos essenciais e outras provisões da Directiva 1999/5/CE.Veja também: http://eudocs.taitworld.com/sv SvenskHärmed intygar Tait Electronics Limited att denna TBBA4A, TBBB1A & TBBH5A står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.Se även: http://eudocs.taitworld.com/
 142 TB7100 Installation and Operation Manual© Tait Electronics Limited December 2005

Navigation menu